K-12629T-1 ESCALE Outline SELF-RIMMING LAVATORY

K-12629T-1 ESCALE Outline SELF-RIMMING LAVATORY
Outline
K-12629T-1
ESCALE
SELF-RIMMING LAVATORY
/
CUT-OUT TEMPLATE / INSTALLATION INSTRUCTIONS
BEFORE YOU BEGIN
·
·
·
·
·
·
·
·
·
·
·
·
Observe all local plumbing and building
codes.
Inspect the waste and supply tubing;
replace if necessary.
Prior to installation, unpack the new
lavatory and carefully inspect it for damage.
Return the lavatory to its protective carton
until you are ready to install it.
For replacement installations, make sure
the existing cutout is the same or smaller
size as the new lavatory.
Use the template supplied with the lavatory
to mark correct size cutout.
Kohler lavatory is made according to
American National Standard that it can
match the American lavatory fittings . Any
other lavatory fittings may not fit for kohler
lavatory.
·
·
Faucet
Supply Lines
Shut-off Valve
·
Drain Assembly
·
·
·
·
·
Turn off the water supply to the faucet.
Open the faucet valves, then disconnect the
supply lines.
Disconnect the drain assembly and remove
the trap.
Remove the existing lavatory.
INSTALL NEW LAVATORY
·
·
·
·
·
·
Cut the template on the cutout line.
Position the template on the countertop to
ensure clearance between the lavatory,
faucet, and backsplash.
Verify cabinet clearance beneath the
countertop.
TOOLS AND MATERIALS
·
·
·
·
·
·
·
·
·
·
·
·
·
(Not Supplied)
(
·
·
·
·
·
·
·
·
·
·
·
·
·
)
13mm
(
)
Template(supplied)
Safety glasses
Pencil
Scissors
Tape measure
Putty knife
Plumbers putty
Hacksaw
Keyhole saw or saber saw
Drill (13mm or 1/2 dia. drill bit or larger)
Adjustable wrench
Pipe wrench
Tubing cutter
·
·
·
·
·
·
13mm
·
·
·
·
ROUGHING-IN
Reference Value
CAUTION: Risk of personal
injury or product damage. Large
lavatories are very heavy. Get help
lifting the lavatory into place.
REMOVE EXISTING
LAVATORY
Unit: mm
:
Trace the template on the countertop with a
pencil.
Re-check the clearance between the
lavatory, faucet, backsplash, and cabinet.
Adjust the template accordingly.
Drill a 13mm hole on the inside of the cutout
opening.
Cut the opening in the countertop along the
inside edge of the pencil line.
Temporaily position the lavatory in the
opening, and adjust to fit.
CAUTION: Risk of personal injury or
product damage. Handle with care.
Product can break, chip or cause injury if
handled carelessly. Get help lifting the
lavatory.
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Immediately wipe away any excess
sealant, and fill any voids as needed.
Verify that the lavatory has not moved
out of position.
Allow the sealant to cure for at least
30 minutes before proceeding.
Connect the faucet supply lines.
Connect the drain assembly.
Open the faucet valves, and check for
leakage.
Clean up with a non-abrasive cleaner.
IMPORTANT CONSUMER
INFORMATION (CARE
AND CLEANING)
To keep your lavatory looking new, make sure you
rinse it out thoroughly after each use. DO NOT
USE ABRASIVES on this product, as they will
scratch and ruin the surface. Stubborn stains, paint,
or tar can be removed with turpentine or paint
thinner.
SERVICE PARTS
1074572-**
Overflow Cover
600
60
35
228
·
·
·
·
·
·
·
·
·
·
·
·
450
Trace a pencil line around the outside edge
of the lavatory.
Remove the lavatory.
Install the faucet and drain according to the
manufacturers instructions.
Apply two beads of sealant to the inside of
the pencil line.
Spread the sealant evenly with a putty knife.
Carefully position the lavatory in the cutout,
and press down firmly.
130
185
45
1133435-T01-A
528137
Kohler reserves the right to change marked dimensions without prior notice.
CUT ALONG THIS LINE
540 mm
, 2009
ã
ã Copyright Kohler China Ltd., 2009
400 mm
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising