VHDL Handbok

VHDL Handbok
VHDL
handbook
Contents
Contents
Lexical elements.............................................................. 4
Definition.................................................................................................4
Character set............................................................................................4
Separators................................................................................................4
Delimiters................................................................................................4
Identifiers.................................................................................................4
Literals................................................................................... 5
Numerical literals....................................................................................5
Enumeration literals.................................................................................5
String literals............................................................................................5
Bit string literals......................................................................................5
The NULL literal.....................................................................................5
Reserved words.................................................................. 6
Syntax....................................................................................... 7
Standards.................................................................................................7
The Backus-Naur-format.........................................................................7
Types and objects.............................................................. 8
Predefined types.......................................................................................8
Predefined subtypes.................................................................................8
Types and subtypes..................................................................................9
ARRAY..................................................................................................10
RECORD...............................................................................................11
ACCESS TYPES (pointers)..................................................................12
Aggregates.............................................................................................13
GROUP..................................................................................................14
ATTRIBUTE.........................................................................................15
Constant declaration..............................................................................16
Variable declaration...............................................................................17
Signal declaration..................................................................................18
File declaration/File handling................................................................19
File reading (TEXTIO)..........................................................................20
File writing (TEXTIO)..........................................................................21
ALIAS...................................................................................................22
Libraries............................................................................... 23
LIBRARY and USE...............................................................................23
Design units......................................................................... 24
PACKAGE DECLARATION................................................................24
PACKAGE BODY.................................................................................25
ENTITY.................................................................................................26
ARCHITECTURE.................................................................................27
CONFIGURATION...............................................................................28
Sequential statements................................................ 29
WAIT.....................................................................................................29
IF............................................................................................................30
CASE.....................................................................................................31
LOOP, NEXT and EXIT........................................................................32
FUNCTION...........................................................................................33
PROCEDURE.......................................................................................34
Version 3.1
Copyright © 1997-2000 HARDI Electronics AB
Contents
RETURN...............................................................................................35
Variable assignment...............................................................................36
Signal assignment..................................................................................37
Concurrent and sequential statements......... 38
ASSERT/REPORT................................................................................38
Subprogram call.....................................................................................39
Concurrent statements............................................. 40
PROCESS..............................................................................................40
WHEN...................................................................................................41
SELECT.................................................................................................42
BLOCK..................................................................................................43
Generic parameters and GENERATE...................... 44
GENERIC/GENERIC MAP..................................................................44
GENERATE...........................................................................................45
Components......................................................................... 46
Component declaration..........................................................................46
Component instantiation........................................................................47
Default configuration.............................................................................48
Configuration specification....................................................................49
Configuration declaration......................................................................50
Predefined attributes................................................. 51
Attributes on types.................................................................................51
Attributes on arrays...............................................................................52
Attributes on signals..............................................................................53
Attributes on named entities..................................................................54
IEEE............................................................................................ 56
VHDL standards....................................................................................56
Predefined packages..............................................................................56
STANDARD.....................................................................................................56
TEXTIO............................................................................................................57
STD_LOGIC_1164...........................................................................................58
NUMERIC_BIT................................................................................................60
NUMERIC_STD...............................................................................................61
MATH_REAL...................................................................................................63
MATH_COMPLEX..........................................................................................64
VHDL guide............................................................................ 66
Introduction...........................................................................................66
File notation...........................................................................................66
Predefined packages..............................................................................66
VHDL syntax.........................................................................................66
Simulation and synthesis.......................................................................69
VHDL’87 and VHDL’93, differences............................ 70
Index......................................................................................... 74
Copyright © 1997-2000 HARDI Electronics AB
Lexical elements
Lexical elements
Definition
LRM
§ 13
• The text of a design file is a sequence of lexical elements.
• Lexical elements are divided into the following groups:
- delimiter
- identifier (may be a reserved word)
- abstract literal (integer or floating point type)
- character literal (a graphical character surrounded by ‘, e.g.: ‘H’)
- string literal (a sequence of graphical characters surrounded by ”, e.g.: ”HARDI”)
- bit string literal (a sequence of extended digits* surrounded by ”, e.g.: ”011”)
- comment (preceded by -- and is valid until the end of the line)
Character set
The character set in VHDL’87 is 128 characters, in VHDL’93 it is 256
characters (see page 8, 56). The character set is divided into seven groups
– Uppercase letters, Digits, Special characters, The space characters, Lowercase letters, Other special characters and format effector.
Separators
Separators are used to separate lexical elements. An example is the space
character (SPACE).
Delimiters
A delimiter is one of the following characters or character combinations:
& ‘ ( ) * + , - . / : ; < = > | [ ]
=> ** := /= >= <= <>
Identifiers
An identifier is either a name or a reserved word (see page 6). There are
two kinds of identifiers:
• Basic identifiers
- Must begin with a letter.
- May contain letters and digits.
- May contain the character ‘_’, but not as first or last character and not more than
one in a row.
- Are not case-sensitive.
• Extended identifiers**
- May contain letters and digits.
- Begins and ends with the character ‘\’.
- The \ character may be included in the identifier, but must then be doubled, e.g.:
\ab\\cd\
- May include an unlimited amount of all graphical characters and in any order.
- Are case-sensitive.
*
**
Possible values for an extended digit is determined by the base for the bit
string literal (see page 5).
New to VHDL’93
Copyright © 1997-2000 HARDI Electronics AB
Literals
Literals
LRM
§ 7.3.1, 13.4-7
A literal is a written value of a type. The are in total five different kinds
of literals.
Numerical literals
[universal_integer, universal_real, literals of physical types]
Numerical literals of universal_integer do not include a point, literals of
universal_real do include a point, while literals of physical types may
include a point and must include a unit.
All numerical literals may include:
• ‘_’ to increase readability, e.g.: 1_000
• ‘E’ or ‘e’ to include an exponent, e.g.: 5E3 (i.e. 5000).
• ‘#’ to describe a base, e.g.: 2#1010# (i.e. 10). It is possible to have a base
between 2 and 16.
A physical type must include a space between its value and its unit, e.g.:
1 ns
Enumeration literals
[e.g.: BIT, BOOLEAN, CHARACTER]
Enumeration literals are graphical characters or identifiers (see page 4), e.g.:
(reset, start, ‘a’, ‘A’).
String literals
[e.g.: STRING)
String literals are one-dimensional arrays including character literals. They
always begin end end with a ” (the ” character may be included in the literal,
but must then be doubled, e.g.: ”A ”” character”).
Bit string literals
[e.g: BIT_VECTOR, STD_LOGIC_VECTOR*]
Bit string literals are one-dimensional arrays including extended digits (see
page 4). They always begin and end with a ”.
It is possible to include a base for a bit string literal. There are three bases:
B- Binary (possible values: 0 - 1).
O- Octal (possible values: 0 - 7). Each value is replaced by three
values (‘0’ or ‘1’).
X- Hexadecimal (possible values: 0 - 9, A - F, a - f). Each value is
replaced by four values (‘0’ or ‘1’).
A bit string literal may include ‘_’ to increase readability, e.g.: ”0100_
0111”.
The NULL literal
[NULL]
The NULL literal is only used for access types, i.e. pointers (see page 12),
and imply that the pointer is empty, i.e. not pointing anywhere.
*
New to VHDL’93 (see page 73)
Copyright © 1997-2000 HARDI Electronics AB
Reserved words
Reserved words
LRM
§ 13.9
abs
if
register
access
impure*
reject*
after
in
rem
alias
inertial*
report*
all
inout
return
and
is
rol*
architecture
label
ror*
array
library
select
assert
linkage
severity
attribute
literal*
signal
begin
loop
shared*
block
map
sla*
body
mod
sll*
buffer
nand
sra*
bus
new
srl*
case
next
subtype
component
nor
then
configuration
not
to
constant
null
transport
disconnect
of
type
downto
on
unaffected*
else
open
units
elsif
or
until
end
others
use
entity
out
variable
exit
package
wait
file
port
when
for
postponed*
while
function
procedure
with
generate
process
xnor*
generic
pure
xor
group
range
*
guarded
*
*
record
New to VHDL’93
Copyright © 1997-2000 HARDI Electronics AB
Syntax
Syntax
Standards
The syntax in this handbook describes VHDL’93. At pages 70-73 the main
differences between VHDL’87 and VHDL’93 are explained.
The Backus-Naur-format
All syntax in this handbook is described using the so called Backus-Naurformat. Here follows a short summary of the format:
• Words written using lower-case letters and possibly one or many hyphens,
are used to denote a syntactical category, for example: entity-declaration.
• Reserved words are written with bold characters, for example: entity.
• Every replacement rule contains a left hand side expression and a right
hand side expression separated by the sign –›, which means ”looks as”
or ”may be replaced with”. The left hand side of the expression is always
a syntactical category and may be replaced by the right hand side of the
expression.
• |, a vertical line (the pipe sign) is used to separate many mutually exclusive
alternatives.
• [], square brackets surround optional things that may occur once or not at
all.
• {}, braces surround optional things that may occur once, many times or
not at all.
• (), parenthesis are used to clarify how and in which order a rule is evaluated.
• Reserved words and characters surrounded by apostrophes, ‘ ’, are included
”as is” in the source code.
• Italicized words in the beginning of the name of a syntactical category
give semantic information and have no syntactical meaning. For example
entity-name-identifier is the same as identifier.
Copyright © 1997-2000 HARDI Electronics AB
Types and objects
Types and objects
LRM
Predefined types
§ 3, 4.3
Type
Possible values
INTEGER
At least:
-2147483647 -
2147483647
ABS **
* / MOD REM
+ - (sign)
+ = /= < <= > >=
REAL
At least:
-1.0E38 -
1.0E38
ABS **
* /
+ - (sign)
+ = /= < <= > >=
TIME
At least:
-2147483647 -
2147483647
(fs, ps, ns,
us, ms, sec,
min, hr)
ABS
* /
+ - (sign)
+ = /= < <= > >=
BIT
‘0’,’1’
NOT
= /= < <= > >=
AND NAND OR NOR XOR XNOR*
BOOLEAN
FALSE, TRUE
NOT
= /= < <= > >=
AND NAND OR NOR XOR XNOR*
BIT_VECTOR
Unconstrained
array of BIT
NOT
&
SLL* SRL* SLA* SRA* ROL* ROR*
= /= < <= > >=
AND NAND OR NOR XOR XNOR*
Type
Possible values
CHARACTER
128 characters in VHDL’87 [ISO 646-1983]
256 characters in VHDL’93 [ISO 8859-1 : 1987(E)]
SEVERITY_LEVEL
*
FILE_OPEN_KIND (by priority)
NOTE, WARNING, ERROR, FAILURE
READ_MODE, WRITE_MODE, APPEND_MODE
FILE_OPEN_STATUS*OPEN_OK, STATUS_ERROR, NAME_ERROR, MODE_ERROR
STRING
Unconstrained array of CHARACTER
Predefined subtypes
Type
Possible values
NATURAL
0 - INTEGER’HIGH The same as for INTEGER
POSITIVE
1 - INTEGER’HIGH The same as for INTEGER
*
DELAY_LENGTH *
Operators (by priority)
0 fs - TIME’HIGH The same as for TIME
New to VHDL’93
Copyright © 1997-2000 HARDI Electronics AB
Types and objects
Types and subtypes
LRM
Syntax
§ 4.1, 4.2
type-declaration –›
type identifier is type-indication ‘;’
subtype-declaration –›
subtype identifier is subtype-indication ‘;’
subtype-indication, type-indication –›
[ resolution-function-name ] type-name [ range-constraint | index-constraint ]
Examples
TYPE Weight IS RANGE 0 TO 10_000
UNITS
gr;
kg = 1000 gr;
ton = 1000 kg;
END UNITS;
ARCHITECTURE Behave OF Design IS
TYPE StateMachine IS (start,count,steady);
SIGNAL state, nextState : StateMachine;
BEGIN
...
END ARCHITECTURE Behave;
PROCESS
SUBTYPE MyArray IS BIT_VECTOR(7 DOWNTO 3);
BEGIN
...
END PROCESS;
Operators (by priority)
• Only relational operators (=, /=, <, <=, > and >=) are predefined for user-defined
enumerated types. Other operators must be defined by the user.
• Logical operators are predefined for the predefined enumerated types BIT and
BOOLEAN (see page 7).
• A subtype shares the same operators as its base type, including their priority.
Comments
• Operators must be defined by the user for user-defined enumerated types (except
for the relational operators). It is therefore preferable to use subtypes since they
share the same operators as their base type.
• Other relational operators than ’=’ and ’/=’ are dependant upon the order in the
enumerated type. They shall therefore be used with care.
• A new type that is a part of an existing type, for example a part of the predefined
unconstrained array BIT_VECTOR, must be declared as a subtype.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
Types and objects
ARRAY
LRM
Syntax
§ 3.2.1
array-type-declaration –›
type identifier is array ‘(’ type-name range ‘<>’ { ‘,’ type-name range ‘<>’ } ‘)’
of element-subtype-indiciation ‘;’ |
type identifier is array index-constraint of element-subtype-indication ‘;’
element-subtype-indication –›
[ resolution-function-name ] type-name [ range-constraint | index-constraint ]
Examples
TYPE ArrayType IS ARRAY(4 DOWNTO 0) OF BIT;
SIGNAL myArray : ArrayType;
...
myArray(3) <= ‘0’;
myArray <= myArray ROL 2; -- Rotate two steps to the left
myArray <= myArray(2 DOWNTO 0) & myArray(4 DOWNTO 3); -- The same
TYPE ThreeDim IS ARRAY(1 TO 2, 1 TO 3) OF BIT_VECTOR(1 TO 4);
SIGNAL complex : ThreeDim := ((”0000”,”0001”,”0010”),
(”1000”,”1001”,”1010”));
TYPE Index IS (A,B,C,D); -- Enumerated type
TYPE AnArray IS ARRAY(Index) OF INTEGER; -- Array with four
-- elements
SIGNAL myArray : AnArray;
...
myArray(B) <= 7;
TYPE UnconstrainedArray IS ARRAY (NATURAL RANGE <>) OF REAL;
Operators (by priority)
1. NOT
2. &
3. SLL*, SRL*, SLA*, SRA*, ROL*, ROR*
4. =, /=, <, <=, >, >=
5. AND, OR, NAND, NOR, XOR, XNOR*
*
New to VHDL’93
(only for BIT and BOOLEAN)
(only for BIT and BOOLEAN)
(only for BIT and BOOLEAN)
Comments
• The logical operators and the shift operators are only defined for arrays with
elements of the types BIT or BOOLEAN.
• An array may be indexed in an unlimited amount of dimensions.
• The shift operators shifts either arithmetically (for example SLA) or logically (for
example SLL). An arithmetic shift fills the last element with the same value it had
before the shift, a logic shift fills it with ‘0’ or FALSE.
• An array may be indexed by any discrete type.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
10
Copyright © 1997-2000 HARDI Electronics AB
Types and objects
RECORD
LRM
Syntax
§ 3.2.2
record-type-declaration –›
type identifier is record
element-declaration
{ element-declaration }
end record [ record-type-name-identifier ] ‘;’
Examples
TYPE Clock IS RECORD
Hour : INTEGER RANGE 0 TO 23;
Min : INTEGER RANGE 0 TO 59;
Sec : INTEGER RANGE 0 TO 59;
END RECORD Clock;
ARCHITECTURE Behave OF Design IS
SIGNAL intTime : Clock := (0,0,0);
BEGIN
PROCESS(clk)
BEGIN
IF clk’EVENT AND clk = ‘1’ THEN
IF intTime.Hour = 23 THEN
...
REPORT ”The time is ” & INTEGER’IMAGE(intTime.Hour) & ”:” &
INTEGER’IMAGE(intTime.Min) & ”:” &
INTEGER’IMAGE(intTime.Sec);
END PROCESS;
END ARCHITECTURE Behave;
Operators (by priority)
• Only the relational operators (=, /=) are predefined for records.
Comments
• There are no predefined records in VHDL, but user-defined records can be very
useful. A record holds several units within a ”group” and the code gets easier to
read.
• A record may contain an unlimited amount of elements.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
11
Types and objects
ACCESS TYPES (pointers)
Syntax
LRM
§ 3.3
access-type-declaration –›
type identifier is access subtype-indication ‘;’
subtype-indication –›
[ resolution-function-name ] type-name [ range-constraint | index-constraint ]
Examples
TYPE ListElement; -- Incomplete type declaration
TYPE ListPointer IS ACCESS ListElement;
TYPE ListElement IS RECORD
Data : INTEGER RANGE 0 TO 31;
NextPoint : ListPointer;
END RECORD ListElement;
VARIABLE list1, list2 : ListPointer;
...
list1 := NEW ListElement;
list1.Data := inData;
list1.NextPoint := NEW ListElement’(inData2,NULL);
IF list1.ALL = list2.ALL THEN ... -- If the elements pointed out
-- have the same values IF list1 = list2 THEN ... -- If the pointers point at the same
-- object
...
DEALLOCATE(list1.NextPoint); -- Remove ”list1.NextPoint”
DEALLOCATE(list1); -- Remove the pointer ”list1”
Operators (by priority)
• Only the relational operators (=, /=) are predefined for access types (pointers).
• Two pointers are equal only if they point at the same object.
Comments
• Access types (pointers) are not synthesizable.
• An object of an access type must be a variable.
• Access types are for example used when flexible handling of the computers’
memory is desired, for example when simulating large memories.
• There is one predefined access type in the package TEXTIO (see page 57). It is
the type LINE that specifies which line that has been read or that shall be written
to.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
12
Copyright © 1997-2000 HARDI Electronics AB
Types and objects
Aggregates
LRM
Syntax
§ 7.3.2
aggregate –›
‘(’ element-association { ‘,’ element-association } ‘)’
element-association –›
[ choices ‘=>’ ] expression
choices –› choice { | choice }
choice –› simple-expression | discrete-range | element-simple-name | others
Examples
TYPE Clock IS RECORD
Hour : INTEGER RANGE 0 TO 23;
Min : INTEGER RANGE 0 TO 59;
Sec : INTEGER RANGE 0 TO 59;
END RECORD Clock;
TYPE Matrix IS ARRAY (0 TO 1, 0 TO 1) OF BIT;
SUBTYPE MyArray IS BIT_VECTOR(2 TO 5);
CONSTANT allZero : MyArray := (OTHERS => ‘0’);
...
SIGNAL currentTime, alarmTime : Clock;
...
VARIABLE m1, m2 : Matrix;
VARIABLE v1, v2 : MyArray;
...
currentTime <= (10,15,5);
alarmTime <= (Hour => 10, Min => 15, Sec => 5);
m1 := ((‘0’,’1’),(OTHERS => ‘0’)); -- ”01”,”00”
m2 := (OTHERS => (OTHERS => ‘1’)); -- ”11”,”11”
v1 := (‘0’, ‘1’, ‘1’, ‘1’); -- ”0111”
v2 := (3 => ‘0’, OTHERS => ‘1’); -- ”1011”
(v1,v2) := (”0000”,”1111”); -- v1 = ”0000”, v2 = ”1111”
-- For a BIT_VECTOR this assignment is easier to write:
v2 := ”1011”;
Comments
• Aggregates are used to assign values to arrays and records. Both types and
objects can get values using aggregates.
• It is possible to use named association (for example ”alarmTime” above) or
positional association (for example ”currentTime” above). Named association is
preferable since then the order of the parameters does not impact the assignment.
• OTHERS is used to assign values to the elements not already assigned. OTHERS
must be placed as the last association in the aggregate.
• For records, but not for arrays, it is possible (but not recommendable) to mix
named and positional association. The only rule is that the positional associations
must be placed before the named. Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
13
Types and objects
GROUP
Syntax
LRM
§ 4.6, 4.7
group-template-declaration –›
group identifier is ‘(’ entity-class [ ‘<>’ ] { ‘,’ entity-class [ ‘<>’ ] } ‘)’ ‘;’
group-declaration –›
group identifier ‘:’ group-template-name ‘(’ ( name | character-literal )
{ ‘,’ ( name | character-literal ) } ‘)’ ‘;’
Examples
ENTITY Mux IS
PORT(a, b, c : IN STD_ULOGIC;
choose : IN STD_ULOGIC_VECTOR(1 DOWNTO 0);
q : OUT STD_ULOGIC);
END ENTITY Mux;
ARCHITECTURE Behave OF Mux IS
GROUP Ports IS (SIGNAL <>); -- Create a group template
GROUP InPorts : Ports (a,b,c);-- Create a group of the template
GROUP OutPort : Ports (q); -- Create another group
GROUP InToOut IS (GROUP,GROUP); -- A 2-dim group template
GROUP Timing : InToOut (InPorts,OutPort); -- The final group
ATTRIBUTE synthesis_maxdelay : TIME; -- Use the groups
ATTRIBUTE synthesis_maxdelay OF Timing : GROUP IS 9 ns;
BEGIN
PROCESS(a,b,c,choose)
BEGIN
CASE choose IS
WHEN ”00” => q <= a;
WHEN ”01” => q <= b;
WHEN ”10” => q <= c;
WHEN OTHERS => NULL;
END CASE;
END PROCESS;
END ARCHITECTURE Behave;
Comments
• Groups are new to VHDL’93. They are intended to make the user-defined attributes (see page 15) more powerful by giving the possibility to set an attribute for a
whole group, not just on named entities each by each.
• The usage of a group contains two parts – group template declaration and group
declaration. The group template declaration creates a template defining the
design of the group, while the group declaration creates the group and includes
its members.
• ‘<>’ (pronounced: box) , means that any number of elements of an entity class
may be included in the group. ‘<>’ may only be used as the last element in a
template list.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
14
Copyright © 1997-2000 HARDI Electronics AB
Types and objects
ATTRIBUTE
LRM
Syntax
§ 4.4, 5.1
attribute-declaration –›
attribute identifier ‘:’ ( type-name | subtype-name ) ‘;’
attribute-specification –›
attribute attribute-name-identifier of entity-class-name-list ‘:’ ( entity | architec.|
configuration | procedure | function | package | type | subtype | constant | signal
| variable | component | label | literal | units | group | file ) is expression ‘;’
entity-class-name-list –›
entity-class-tag [ signature ] { ‘,’ entity-class-tag [ signature ] } | others | all
Examples
TYPE StateMachine IS (start,count,stop);
ATTRIBUTE syn_encoding : STRING; -- State machine encoding
ATTRIBUTE syn_encoding OF StateMachine : TYPE IS ”onehot”;
ARCHITECTURE Behave OF Mux IS
GROUP Ports IS (SIGNAL <>);
GROUP InPorts : Ports (a,b,c);
GROUP OutPort : Ports (q);
GROUP InToOut IS (GROUP,GROUP);
GROUP Timing : InToOut (InPorts,OutPort);
ATTRIBUTE synthesis_maxdelay : TIME; -- Maximum delay
ATTRIBUTE synthesis_maxdelay OF Timing : GROUP IS 9 ns;
BEGIN
...
END ARCHITECTURE Behave;
ENTITY Count IS
PORT(clock : IN BIT;
counter : OUT INTEGER RANGE 0 TO 15);
ATTRIBUTE pinnum : STRING; -- Pin numbering
ATTRIBUTE pinnum OF clock : SIGNAL IS ”P2”;
ATTRIBUTE pinnum OF counter : SIGNAL IS ”P12,P14,P17,P21”;
END ENTITY Count;
Comments
• The usage of attributes contains two parts – attribute declaration and attribute
specification. The attribute declaration defines the attribute while the attribute
specification uses the attribute on a named entity, for example a signal, a variable,
a function, a type etc.
• In VHDL’93 it is possible to group (GROUP, see page 14) a number of named
entities and then define an attribute for the whole group.
• Attributes are used for documentation purposes, but above all to give commands
to downstream tools, for example synthesis tools. Attributes used for downstream
tools are not defined in the VHDL standard and differ between different tools.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
Only spec.!
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
15
Types and objects
Constant declaration
Syntax
LRM
§ 4.3.1.1
constant-declaration –›
constant identifier { ‘,’ identifier } ‘:’ subtype-indication [ ‘:=’ expression ] ‘;’
subtype-indication –›
[ resolution-function-name ] type-name [ range-constraint | index-constraint ]
Examples
CONSTANT zero : STD_LOGIC_VECTOR(0 TO 3) := (OTHERS => ‘0’);
SIGNAL data : STD_LOGIC_VECTOR(zero’RANGE) := zero;
CONSTANT bits : BIT_VECTOR := x”0FA3”;
PACKAGE Useful IS
CONSTANT pi
: REAL; -- declare pi here ...
CONSTANT one : NATURAL := 1;
CONSTANT two : NATURAL := 2*one;
CONSTANT four : NATURAL := two + one + one;
END PACKAGE Useful;
PACKAGE BODY Useful IS
CONSTANT pi : REAL := 3.1415; -- ... and give it its value here
END PACKAGE BODY Useful;
Comments
• A constant gets its value when it is declared and may only be read.
• A constant can be declared using a so called deferred constant declaration. It is
then declared and named in the package declaration, but gets its value first in the
package body. This coding style hides the value of the constant, it is not shown in
the package declaration, and the user is not tempted to use the value directly. Another advantage is if the value of the constant is modifed. Then only the package
body needs to be recompiled.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
16
Copyright © 1997-2000 HARDI Electronics AB
Types and objects
Variable declaration
LRM
Syntax
§ 4.3.1.3
variable-declaration –›
[ shared ] variable identifier { ‘,’ identifier } ‘:’ subtype-indication
[ ‘:=’ expression ] ‘;’
subtype-indication –›
[ resolution-function-name ] type-name [ range-constraint | index-constraint ]
Examples
VARIABLE databus : STD_LOGIC_VECTOR(3 DOWNTO 0);
Clocked: PROCESS(clk)
VARIABLE internal : REAL := 0.0;
BEGIN
IF clk’EVENT AND clk = ‘1’ THEN
internal := internal + 1.0;
output <= internal;
END IF;
END PROCESS Clocked;
ARCHITECTURE Behave OF Design IS
SHARED VARIABLE data : INTEGER := 0;
BEGIN
One: PROCESS
BEGIN
data := 0;
...
END PROCESS One;
Another: PROCESS
BEGIN
IF data = 0 THEN
...
END PROCESS Another;
END ARCHITECTURE Behave;
Comments
• Variables are local in processes or subprograms and are therefore declared there.
The exception is shared variables that are global just as signals. Since variables
do not have the possibility to handle concurrent assignment from more than one
process, as signals can, shared variables are to be avoided.
• A variable has no direction and may therefore be both read and written.
• Variables are both assigned and get default values using ‘:=’.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
Shared
... ... BEGIN
Shared
Shared
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION
Conf OF Ent IS
Shared
Shared
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
Local
Local
Local
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
17
Types and objects
Signal declaration
Syntax
LRM
§ 4.3.1.2
signal-declaration –›
signal identifier { ‘,’ identifier } ‘:’ subtype-indication [ register | bus ]
[ ‘:=’ expression ] ‘;’
subtype-indication –›
[ resolution-function-name ] type-name [ range-constraint | index-constraint ]
Examples
SIGNAL data : STD_LOGIC_VECTOR(3 DOWNTO 0);
ENTITY Fir IS
PORT(dataIn : IN MyDataType;
dataOut : OUT MyDataType;
clock : IN STD_ULOGIC);
END ENTITY Fir;
ENTITY Design IS
PORT(clock : IN STD_ULOGIC;
result : OUT MyResultType);
TYPE ThreeDim IS ARRAY(1 TO 2, 1 TO 3) OF BIT_VECTOR(1 TO 4);
SIGNAL complex : ThreeDim := ((”0000”,”0001”,”0010”),
(”1000”,”1001”,”1010”));
END ENTITY Design;
Comments
• Signals are global in an architecture or in a block. They may therefore not be
locally declared in a process or in a function.
• A signal declared in a PORT must have a direction, while an internal signal
(declared in an architecture, a block or in a package) does not have a direction.
• Ports of the mode OUT may only be assigned, not read. The workaround is to use
internal variables or the attribute ‘DRIVING_VALUE (see page 54).
• Signals are assigned using ‘<=’ but get default values using ‘:=’.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
18
Copyright © 1997-2000 HARDI Electronics AB
Types and objects
File declaration/File handling
LRM
Syntax
§ 3.4, 4.3.1.4
file-declaration –›
file identifier { ‘,’ identifier } ‘:’ subtype-indication
[ [ open file-open-kind-expression ] is string-expression ] ‘;’
subtype-indication –›
type-name [ range-constraint | index-constraint ]
Examples
ARCHITECTURE Behave OF Files IS
TYPE Times
IS FILE OF TIME;
TYPE Stimuli IS FILE OF BIT_VECTOR(3 DOWNTO 0);
FILE outFile : Stimuli OPEN WRITE_MODE IS ”C:\proj\out.bin”;
FILE timeFile : Times
OPEN READ_MODE IS ”C:\proj\time.bin”;
FILE inData : Stimuli;
BEGIN
...
VARIABLE ok : FILE_OPEN_STATUS;
VARIABLE t : TIME;
VARIABLE bv : BIT_VECTOR(3 DOWNTO 0);
...
FILE_OPEN(ok,inData,”C:\proj\indata.bin”,READ_MODE); IF ok = OPEN_OK THEN
WHILE (NOT ENDFILE(inData) AND NOT ENDFILE(timeFile)) LOOP
READ(timeFile,t);
READ(inData,bv);
WAIT FOR t;
WRITE(outFile,bv);
...
FILE_CLOSE(outFile);
FILE_CLOSE(timeFile);
FILE_CLOSE(inData);
...
END ARCHITECTURE Behave;
Comments
• A file may contain all types in VHDL except for files, access types (pointers) and
multidimensional arrays.
• The VHDL standard does not define how data shall be stored in a file. It is
therefore preferable to use text files since they are easy to read and since there is
a number of predefined procedures to handle them. The procedures are defined
in the package TEXTIO (see page 57). By using this standardized package it is
possible to move the files between different simulation environments.
• File handling in VHDL has been considerably modified between VHDL’87 and
VHDL’93 (see page 71). The modifications are not backwards compatible.
• FILE_OPEN and FILE_CLOSE are new to VHDL’93.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
19
Types and objects
File reading (TEXTIO)
Syntax
LRM
§ 14.3
(No syntax)
Examples
USE STD.TEXTIO.ALL; -- Make TEXTIO accessible
ARCHITECTURE Behave OF Filehandling IS
TYPE Reg IS RECORD
Number : POSITIVE;
Sum : NATURAL;
END RECORD;
FILE MyFile : TEXT OPEN READ_MODE IS ”data.txt”;
BEGIN
PROCESS
VARIABLE l : LINE; -- declare a line variable
VARIABLE fNumber : POSITIVE;
VARIABLE fSum : NATURAL;
BEGIN
IF NOT ENDFILE(MyFile) THEN -- If the file is not empty ...
READLINE(MyFile,l); -- ... read a line ...
ASSERT l’LENGTH /= 0; -- ... if it isn’t empty ..
READ(l,fNumber); -- ... read the 1st element ...
READ(l,fSum); -- ... and then the 2nd element
...
END ARCHITECTURE Behave;
VARIABLE l : LINE;
l := NEW STRING’(”My question”);
WRITELINE(OUTPUT,l); -- Writes ”My question” in the simulator
READLINE(INPUT,l); -- Reads the answer from the keyboard
Comments
• When reading a text file, a whole line must first be read. That is done using
READLINE. After that each element in the line is read using a number of READ
operations. Each object assigned by a value from the file must be of the same type
as the value. It is therefore important to know the order of the elements in the file.
• The predefined file INPUT (see example above) reads a value from the keyboard
or from an input file during simulation. The handling of INPUT is tool dependant.
• Files are not synthesizable.
• File handling in VHDL has been considerably modified between VHDL’87 and
VHDL’93 (see page 71). The modifications are not backwards compatible. The
examples above are according to VHDL’93.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
20
Copyright © 1997-2000 HARDI Electronics AB
Types and objects
File writing (TEXTIO)
LRM
Syntax
§ 14.3
(No syntax)
Examples
USE STD.TEXTIO.ALL; -- Make TEXTIO accessible
ARCHITECTURE Behave OF Filehandling IS
TYPE Reg IS RECORD
Number : POSITIVE;
Sum : NATURAL;
END RECORD;
FILE MyFile : TEXT OPEN WRITE_MODE IS ”data.txt”;
BEGIN
PROCESS
VARIABLE l : LINE; -- declare a line variable
VARIABLE fNumber : POSITIVE;
VARIABLE fSum : NATURAL;
BEGIN
WRITE(l,fNumber); -- Write an element to a line ...
WRITE(l,’ ‘); -- ... separate with a blank ...
WRITE(l,fSum); -- ... another element to the same line ...
WRITELINE(MyFile,l); -- ... and write the line to the file
...
END PROCESS;
END ARCHITECTURE Behave;
VARIABLE l : LINE;
l := NEW STRING’(”My question”);
WRITELINE(OUTPUT,l); -- Writes ”My question” in the simulator
READLINE(INPUT,l); -- Reads the answer from the keyboard
Comments
• When writing text to a text file, all elements are first written to a line using
WRITE and finally the whole line is written to the file using WRITELINE.
• The predefined file OUTPUT (see example above) writes to the screen or to an
output file during simulation. No information is given about the current simulation time as it is when using REPORT (see page 38). The handling of OUTPUT is
tool dependant.
• Files are not synthesizable.
• File handling in VHDL has been considerably modified between VHDL’87 and
VHDL’93 (see page 71). The modifications are not backwards compatible. The
examples above are according to VHDL’93.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
21
Types and objects
ALIAS
Syntax
LRM
§ 4.3.3
alias-declaration –›
alias ( identifier | character-literal | operator-symbol ) [ ‘:’ subtype-indication ]
is name [ signature ] ‘;’
signature –› ‘[’ [ type-name { ‘,’ type-name } ] [ return type-name ] ‘]’
subtype-indication –›
[ resolution-function-name ] type-name [ range-constraint | index-constraint ]
Examples
SIGNAL data : SIGNED(7 DOWNTO 0);
ALIAS sign : BIT IS data(7);
...
REPORT ”The sign bit is ” & BIT’IMAGE(sign);
-- The alias below gives a certain index range to be able to
-- calculate n not depending on v’s index range
FUNCTION Bv2Natural(v : IN BIT_VECTOR) RETURN NATURAL IS
ALIAS aliasV : BIT_VECTOR(v’LENGTH - 1 DOWNTO 0) IS v;
VARIABLE n : NATURAL;
BEGIN
...
FOR i IN aliasV’RANGE LOOP
IF aliasV(i) = ‘1’ THEN
n := n + 2**i;
...
RETURN n;
END FUNCTION Bv2Natural;
CONSTANT MaxDelayClockToPad : TIME := 15 ns;
ALIAS MDC2P : TIME IS MaxDelayClockToPad;
-- MDC2P = MaxDelayClockToPad
SUBTYPE MyVeryVeryLongTypeName IS BIT_VECTOR(3 DOWNTO 0);
ALIAS ShortName IS MyVeryVeryLongTypeName;
Comments
• An alias creates an alternative name for an existing object. It does not create a
new object. It is often used to easier get access to elements in one-dimensional
arrays.
• In VHDL’87 it is only possible to declare aliases for objects. In VHDL’93 it is
possible also for subprograms, operators, types and for all named entities except
”labels”, ”loop parameters” and ”generate parameters”.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
22
Copyright © 1997-2000 HARDI Electronics AB
Libraries
Libraries
LIBRARY and USE
LRM
Syntax
§ 11.2, 10.4
library-clause –›
library logical-name-identifier { ‘,’ logical-name-identifier } ‘;’
use-clause –›
use selected-name { ‘,’ selected-name } ‘;’
selected-name –› prefix ‘.’ suffix
Examples
LIBRARY IEEE, HARDI;
USE IEEE.STD_LOGIC_1164.ALL;
USE IEEE.NUMERIC_STD.ALL, HARDI.Devices.ALL;
LIBRARY PACK;
USE WORK.OnePackage.MyType; -- Select a unit from the package
USE PACK.AnotherPackage.ALL; -- Select the whole package
-- The following declarations exist implicitely:
LIBRARY WORK, STD;
USE STD.STANDARD.ALL;
Comments
• The LIBRARY clause declares the name of a library. After that the desired parts
of the library are selected using USE.
• Via ALL everything in a library or package is selected.
• The libraries WORK and STD and also the package STD.STANDARD are
always accessible.
• LIBRARY must be placed before the design unit that shall use it, but USE can
also be placed within the design units. It is however good practice to place both
LIBRARY and USE before the design units that shall use them.
• An architecture has the same LIBRARY and USE as its entity. A package body
has the same as its package declaration. A configuration declaration has the
same as its entity and architecture.
Placement
Blk:BLOCK
LIBRARY, USE
LIBRARY, USE
PACKAGE Pack IS PACKAGE BODY Pack IS ...
USE
... ... BEGIN
USE
USE
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
LIBRARY, USE
LIBRARY, USE
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS LIBRARY, USE
... ... CONFIGURATION
Conf OF Ent IS
USE
USE
BEGIN BEGIN ...
USE
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
USE
USE
USE
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
23
Design units
Design units
PACKAGE DECLARATION
Syntax
LRM
§ 2.5
package-declaration –›
package identifier is
{subprogram-declaration | type-declaration | subtype-declaration |
constant-declaration | signal-declaration | shared-variable-declaration |
file-declaration | alias-declaration | component-declaration |
attribute-declaration | attribute-specification | disconnect-specification |
use-clause | group-template-declaration | group-declaration }
end [ package ] [ package-name-identifier ] ‘;’
Examples
LIBRARY IEEE;
USE IEEE.STD_LOGIC_1164.ALL;
PACKAGE Various IS
CONSTANT hold : TIME; -- deferred constant
PROCEDURE Push(SIGNAL button : INOUT STD_LOGIC; hold : TIME);
TYPE Display IS RECORD
...
END RECORD;
COMPONENT Clock IS
PORT(mode, set, reset, clk : IN STD_LOGIC;
LCD : OUT Display;
backPlane, alarmSignal : OUT STD_LOGIC);
END COMPONENT Clock;
END PACKAGE Various;
Comments
• A package is used for declarations that shall be shared by several design units.
The package contains two parts – package declaration that contains the declarations and package body that implements the contents of the package.
• A package declaration does not need a package body.
• There is a number of packages available in VHDL. The packages standardized by
IEEE are listed on pages 56-65.
Design unit
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
24
Copyright © 1997-2000 HARDI Electronics AB
Design units
PACKAGE BODY
LRM
Syntax
§ 2.6
package-body –›
package body package-name-identifier is
{subprogram-declaration | subprogram-body | type-declaration |
subtype-declaration | constant-declaration | shared-variable-declaration |
file-declaration | alias-declaration | use-clause | group-template-declaration |
group-declaration }
end [ package body ] [ package-name-identifier ] ‘;’
Examples
LIBRARY IEEE; -USE IEEE.STD_LOGIC_1164.ALL; - - --
These two lines could have been
left out since they already are
declared in the package
declaration
PACKAGE BODY Various IS
CONSTANT hold : TIME := 100 ns; -- deferred constant
PROCEDURE Push(SIGNAL button : INOUT STD_LOGIC; hold : TIME) IS
BEGIN
button <= ‘0’, ‘1’ AFTER hold;
WAIT FOR 2*hold;
END PROCEDURE Push;
END PACKAGE BODY Various;
Comments
• A package body is used to implement a package. Usually subprograms are im-
plemented and so called deferred constants, constants declared but not assigned
values in a package declaration, are assigned values.
• It is possible to declare types and subprograms in a package body, but they are
then only accessible within the package body.
• There is a number of packages available in VHDL. The packages standardized
by IEEE are listed on pages 56-65.
• A package body must have a package declaration and they must have the same
name. The package body is compiled after its package declaration.
Design unit
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
25
Design units
ENTITY
Syntax
LRM
§ 1.1
entity-declaration –›
entity identifier is
[ formal-generic-clause ]
[ formal-port-clause ]
{subprogram-decl. | subprogram-body | type-decl. | subtype-decl. | constant decl. | signal-decl. | shared-variable-decl. | file-decl. | alias-decl. | attribute decl. | attribute-spec. | disconnect-spec. | use-clause | group-template-decl. |
group-decl. }
[ begin
{ concurrent-assertion-statement | passive-procedure-call |
passive-process-statement } ]
end [ entity ] [ entity-name-identifier ] ‘;’
Examples
LIBRARY IEEE, TYPES, HARDI;
USE IEEE.STD_LOGIC_1164.ALL;
USE TYPES.TypePackage.ALL;
USE HARDI.Timing.ALL;
ENTITY Design IS
GENERIC (n : NATURAL);
PORT (data : IN STD_LOGIC_VECTOR(n DOWNTO 0);
clk : IN STD_LOGIC;
outData : OUT OutDataType);
BEGIN
PeriodCheck(clk, MaxPeriod); -- Passive procedure call
END ENTITY Design;
Comments
• An entity is the interface of a design.
• The entity contains a declaration part and a statement part. The declaration part
declares the interface of the design, the statement part may contain passive statements, i.e. statements not assigning signals. The purpose of the statement part is
to be able to verify the behavior of the signals declared in the declaration part, i.e.
the ports.
• Each entity in a design must have a unique name while each entity can have
several architectures. Everything declared in an entity is automatically accessible
in its architectures.
• Note the order of the declarations in the declaration part of the entity.
Design unit
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
26
Copyright © 1997-2000 HARDI Electronics AB
Design units
ARCHITECTURE
LRM
Syntax
§ 1.2
architecture-body –›
architecture identifier of entity-name is
{subprogram-declaration | subprogram-body | type-declaration |
subtype-declaration | constant-declaration | signal-declaration |
shared-variable-declaration | file-declaration | alias-declaration |
component-declaration | attribute-declaration | attribute-specification |
configuration-specification | disconnect-specification | use-clause |
group-template-declaration | group-declaration }
begin
{ concurrent-statement }
end [ architecture ] [ architecture-name-identifier ] ‘;’
Examples
ARCHITECTURE Behave OF Design IS
FUNCTION InternalCalc(v : STD_LOGIC_VECTOR(7 DOWNTO 0))
RETURN BIT_VECTOR(1 TO 4) IS
BEGIN
...
END FUNCTION InternalCalc;
SUBTYPE MyArray IS BIT_VECTOR(3 DOWNTO 0);
SIGNAL internal : MyArray;
SHARED VARIABLE data : STD_LOGIC_VECTOR(1 TO 8);
BEGIN
PROCESS(clk)
BEGIN
...
END PROCESS;
internal <= InternalCalc(data);
END ARCHITECTURE Behave;
Comments
• An architecture is the implementation of an entity. It contains a declaration
part and a statement part. The declaration part may for example declare types,
components and subprograms that shall be internal within the architecture.
• An entity may have an unlimited amount of architectures. The architectures associated with the same entity must have unique names.
• An entity and its architectures belong to the same declarative region. Everything
declared in the entity is therefore accessible in its architectures.
• At synthesis or simulation an architecure must be selected for each entity. If
nothing else is specified, for example using a configuration (see page 28, 49-50),
the last compiled architecture is used.
Design unit
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
27
Design units
CONFIGURATION
Syntax
LRM
§ 1.3
configuration-declaration –›
configuration identifier of entity-name is
{ use-clause | attribute-specification | group-declaration }
for block-specification
{ use-clause }
{ block-configuration | component-configuration }
end [ configuration ] [ configuration-name-identifier ] ‘;’
block-specification –›
architecture-name | block-statement-label |
generate-statement-label [ ‘(’ index-specification ‘)’ ]
Examples
LIBRARY COMP;
CONFIGURATION MyConfiguration OF MyEntity IS
FOR MyArchitecture
FOR ALL : SubBlock USE ENTITY WORK.Ent(Arc)
GENERIC MAP(...)
PORT MAP(...);
END FOR;
FOR SubBlock2
FOR C1 : AComponent USE ENTITY COMP.Ent2(Arc2);
END FOR;
END FOR;
END FOR;
END CONFIGURATION MyConfiguration;
Comments
• A CONFIGURATION (configuration declaration) is a separate design unit and is
used to associate the entities and architectures in a design. It can also give values
to generic parameters (see page 44-45).
• A CONFIGURATION is the most powerful of the three available configurations
in VHDL. In VHDL’93 it may connect unconnected ports, ports that was not connected by a configuration specification (see page 49). That is called incremental
binding.
• A CONFIGURATION connects all parts of a design and shall therefore be compiled as the last design unit.
• All three possible configurations are described on pages 48-50.
Design unit
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
28
Copyright © 1997-2000 HARDI Electronics AB
Sequential statements
Sequential statements
WAIT
LRM
Syntax
§ 8.1
wait-statement –›
[ label ‘:’ ] wait [ on sensitivity-list ] [ until boolean-expression ]
[ for time-expression ] ‘;’
sensitivity-list –› signal-name { ‘,’ signal-name }
Examples
SIGNAL s, p : BIT;
...
VARIABLE v : BIT;
VARIABLE t : TIME;
...
WAIT ON s; -WAIT ON s UNTIL s = ‘1’; -WAIT UNTIL s = ‘1’; -WAIT; -WAIT UNTIL v; -WAIT UNTIL NOW = t; -WAIT ON s UNTIL p = ‘1’ FOR t; - - - -WAIT FOR 10 ns; -WAIT FOR t - NOW; - --
Wait for value changes on s
Wait for a rising edge on s
Wait for a rising edge on s
Never passed
Never passed
Never passed
Wait for value changes on s,
then verify that p = ‘1’, or
wait at maximum the time t
(timeout)
Pass WAIT after 10 ns
Pass WAIT after the time t
minus current simulation time
Comments
• The WAIT statement has three conditional parts that may be combined: ON that
detects value changes, UNTIL that verifies a logical expression and FOR that
limits in time (timeout).
• A WAIT statement may exist without a condition and will then never be passed.
• A variable does not have an event and does therefore not work in a WAIT ON
statement. For the same reason expressions without signals do not work in a
WAIT UNTIL statement. Such WAIT statements are suspended forever.
• Most synthesis tools accept just one WAIT statement for each process. The
number is unlimited for simulation. See also page 40 (PROCESS).
• At simulation start every process executes until it reaches its first WAIT statement.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
29
Sequential statements
IF
Syntax
LRM
§ 8.7
if-statement –› [ if-label ‘:’ ]if boolean-expression then
{ sequential-statement }
{ elsif boolean-expression then
{ sequential-statement } }
[ else {sequential-statement } ]
end if [ if-label ] ‘;’
Examples
PROCESS(reset,clk)
BEGIN
IF reset = ‘1’ THEN
...
ELSIF clk’EVENT AND clk = ‘1’ THEN
...
END IF;
END PROCESS;
ANDgate: IF en = ‘1’ THEN
q <= d;
ELSE
q <= ‘0’;
END IF;
Latch: IF en = ‘1’ THEN
q <= d;
END IF;
IF a = Func(i*2#01001001#) THEN
...
END IF;
Comments
• All conditions in an IF statement must be of the type BOOLEAN.
• The syntax for the IF statement is quite odd – ELSIF is spelled as one word
without an intermediate ’E’. END IF is two separate words.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
30
Copyright © 1997-2000 HARDI Electronics AB
Sequential statements
CASE
LRM
Syntax
§ 8.8
case-statement –› [ case-label ‘:’ ]case expression is
when choices ‘=>’ { sequential-statement }
{ when choices ‘=>’ { sequential-statement }
}
end case [ case-label ] ‘;’
choices –› choice { | choice }
Examples
PROCESS
BEGIN
WAIT ON number;
CASE number IS
WHEN 0 =>
WHEN 2 | 5 | 243 =>
WHEN 6 TO 18 =>
WHEN OTHERS =>
END CASE;
END PROCESS;
... -... -... -NULL; --
When ”number” is 0
When ”number” is 2, 5 or 243
In the interval 6 to 18
At all other values, do nothing
SIGNAL s : STD_ULOGIC;
...
CASE s IS
WHEN ‘0’ => ...
WHEN ‘1’ => ...
WHEN OTHERS => NULL; -- Must exist (or a compilation error
-- will occur)
END CASE;
Comments
• The CASE statement must specify all possible values of the expression. If not
all possible values are covered, a compilation error will occur. OTHERS may be
used to cover ”all other values”.
• The expression can be of an integer type, an enumerated type or a one-dimensional array with elements written as characters (for example STRING, BIT_VECTOR, STD_LOGIC_VECTOR etc.).
• Note that the types STD_LOGIC and STD_ULOGIC have more possible values
than ‘0’ and ‘1’. They must also be included in the CASE statement (see above).
• The reserved word NULL is useful in combination with OTHERS. Together they
specify that ”at all other values nothing shall happen”.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
31
Sequential statements
LOOP, NEXT and EXIT
Syntax
LRM
§ 8.9-8.11
loop-statement –›
[ loop-label ‘:’ ] [ while boolean-expression | for identifier in discrete-range ]
loop
{ sequential statement }
end loop [ loop-label ] ‘;’
exit-statement –› [ label ‘:’ ] exit [ loop-label ] [ when boolean-expression ] ‘;’
Examples
L1: LOOP
L2: WHILE count < 15 LOOP
NEXT L2 WHEN value = 12;
count := count + Func(value);
END LOOP L2;
END LOOP L1;
FOR i IN anArray’RANGE LOOP
EXIT WHEN IS_X(anArray(i)); -- Exit if the array contains any
-- ‘U’, ‘X’, ‘Z’, ‘W’ or ‘-’
IF anArray(i) = ‘1’ THEN
REPORT ”There is a 1 at position ” & INTEGER’IMAGE(i);
END IF;
END LOOP;
factorial := 1;
FOR j IN 1 TO n LOOP
factorial := factorial*j;
END LOOP;
Comments
• FOR loops are in general synthesizable, but not WHILE loops.
• FOR loops loop according to a loop variable that shall be an integer or an enumerated type. The loop variable shall not be declared.
• WHILE loops loop as long as a BOOLEAN expression is true.
• EXIT jumps out of the loop and NEXT goes directly to the next iteration, not
executing any code between NEXT and END LOOP.
• It is useful to name loops since it then is possible to specify what loop to exit or
iterate using EXIT or NEXT.
• It is not possible to affect the length of the steps in a FOR loop.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
32
Copyright © 1997-2000 HARDI Electronics AB
Sequential statements
FUNCTION
Syntax
LRM
§ 2.1-2.3
function-declaration –› function-specification ‘;’
function-specification –› [ pure | impure ] function ( identifier | operator )
[ ‘(’ interface-list ‘)’ ] return type-name
function-body –›function-specification is { subprogram-declarative-item }
begin { sequential-statement }
end [ function ] [ function-identifier | operator ] ‘;’
interface-list –› [ constant | signal | file ] identifier { ‘,’ identifier } ‘:’ [ in ]
subtype-indication [ := static_expression ]
Examples
-- declaration
FUNCTION AnyZeros(CONSTANT v : IN BIT_VECTOR) RETURN BOOLEAN;
-- implementation
FUNCTION AnyZeros(CONSTANT v : IN BIT_VECTOR) RETURN BOOLEAN IS
BEGIN
FOR i IN v’RANGE LOOP
IF v(i) = ‘1’ THEN
RETURN TRUE;
END IF;
END LOOP;
RETURN FALSE;
END FUNCTION AnyZeros;
-- Function call
q <= Func(p1 => v1, p2 => v2); -- Named association
q <= Func(v1, v2); -- Positional association
FUNCTION ”AND”(...) RETURN ...; -- A userdefined operator
FUNCTION ”+”(...) RETURN ...; -- Another one
-- Operator call
q <= a + b; -- The types of a, b and q determine which ”+” to
-- call (eventually a user-defined operator)
Comments
• A function returns a single value.
• The formal parameters of a function (the interface-list) are handled as constants
with mode IN if nothing else is specified. Possible parameters are constants and
signals, with mode IN, and files. Parameters with mode IN may only be read.
• A function may not include any WAIT statements.
• It is not permitted to declare signals in subprograms.
• Functions are either PURE or IMPURE. A PURE FUNCTION has no side-effects, i.e. it will always return the same value with the same input parameters, while
an IMPURE FUNCTION may have side-effects (for example assigning signals,
opening files etc.). If nothing else is said the function is considered PURE.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ... Decl,Body
... ... BEGIN
Decl,Body
Decl
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION
Conf OF Ent IS
Decl,Body
Decl,Body
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
Decl,Body
Decl,Body
Decl,Body
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
33
Sequential statements
PROCEDURE
Syntax
LRM
§ 2.1-2.3
procedure-declaration –› procedure-specification ‘;’
procedure-specification –› procedure identifier [ ‘(’ interface-list ‘)’ ]
procedure-body –› procedure-specification is { subprogram-declarative-item }
begin { sequential-statement }
end [ procedure ] [ procedure-identifier ] ‘;’
interface-list –› [ constant | signal | variable | file ] identifier { ‘,’ identifier } ‘:’
[ in | out | inout | buffer | linkage ] subtype-indication [ bus ]
[ := static_expression ]
Examples
-- declaration
PROCEDURE AnyZeros(CONSTANT inArray : IN
VARIABLE result : OUT
-- implementation
PROCEDURE AnyZeros(CONSTANT inArray : IN
VARIABLE result : OUT
BEGIN
result := FALSE; -- default assignment
FOR i IN inArray’RANGE LOOP
IF inArray(i) = ‘1’ THEN
result := TRUE;
END IF;
END LOOP;
END PROCEDURE AnyZeros;
BIT_VECTOR;
BOOLEAN);
BIT_VECTOR;
BOOLEAN) IS
PROCEDURE Finish IS
BEGIN
REPORT ”The simulation stopped at the time ” & TIME’IMAGE(NOW);
END PROCEDURE Finish;
-- The procedure ”Finish” is called when executing the line:
Finish;
Comments
• A procedure may contain a number of parameters that are read and/or modified at
a procedure call. All parameters shall be declared in the procedure’s interface-list
and separated by a ‘;’. If nothing else is specified the parameters are handled as
constants with the mode IN. It is possible to not have any parameters at all.
• The parameters can be constants, variables, signals or files. All parameters with
the mode OUT or INOUT are as default variables, while parameters with the
mode IN are constants. Constants do always have the mode IN, while variables
and signals may be of the modes IN, INOUT or OUT. Files do not have a mode.
• A procedure may contain WAIT statements.
• It is not permitted to declare signals in subprograms.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ... Decl,Body
... ... BEGIN
Decl,Body
Decl
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION
Conf OF Ent IS
Decl,Body
Decl,Body
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
Decl,Body
Decl,Body
Decl,Body
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
34
Copyright © 1997-2000 HARDI Electronics AB
Sequential statements
RETURN
LRM
Syntax
§ 8.12
return-statement –›
[ label ‘:’ ] return [ expression ] ‘;’
Examples
FUNCTION AnyZeros(CONSTANT v : IN BIT_VECTOR) RETURN BOOLEAN IS
BEGIN
FOR i IN v’RANGE LOOP
IF v(i) = ‘1’ THEN
RETURN TRUE; -- Return the value TRUE
END IF;
END LOOP;
RETURN FALSE; -- Return the value FALSE
END FUNCTION AnyZeros;
PROCEDURE AnyZeros(CONSTANT inArray : IN STD_LOGIC_VECTOR;
VARIABLE result : OUT BOOLEAN) IS
BEGIN
IF IS_X(inArray) THEN
REPORT ”Unacceptable values”;
RETURN; -- Exit the procedure
END IF;
result := FALSE; -- default assignment
FOR i IN inArray’RANGE LOOP
IF inArray(i) = ‘1’ THEN
result := TRUE;
END IF;
END LOOP;
END PROCEDURE AnyZeros;
Comments
• RETURN is used to exit subprograms. A RETURN statement in a function must
return a value, while a RETURN statement in a procedure must not have a value.
A procedure returns all values via its formal parameters.
• A function should contain at least one RETURN statement (without RETURN
the function is rather meaningless). It determines what value that will be returned
from the function.
• A procedure may contain RETURN, but it is not necessary. If it is included it is
used to exit the procedure. If no RETURN statement exists, the procedure will
end after the final line has been executed. RETURN can not return any value in a
procedure as it can in a function.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
35
Sequential statements
Variable assignment
Syntax
LRM
§ 8.5
variable-assignment-statement –›
[ label ‘:’ ] ( variable-name | variable-aggregate ) ‘:=’ expression ‘;’
Examples
ARCHITECTURE Behave OF Design IS
SHARED VARIABLE globalVariable : INTEGER;
BEGIN
PROCESS
VARIABLE internalVariable : REAL;
BEGIN
sharedVariable := INTEGER(internalVariable);
...
END PROCESS;
END ARCHITECTURE Behave;
PROCESS
VARIABLE a : INTEGER := 0;
BEGIN
First : a := a + 2;
Second: a := a + 4;
Final : a := a - 3;
REPORT INTEGER’IMAGE(a); -- a = 3 (i.e. 0 + 2 + 4 - 3)
END PROCESS;
v := (2#0100# + Func(2.0*3.14))/ABS(x);
Comments
• A variable assignment immediately updates the value of the variable. The assignment uses ‘:=’, i.e. the same sign used for default assignments.
• A variable can be assigned the value of a signal and vice versa.
• The expression in the variable assignment may be arbitrarily complex and for
example include subprogram calls.
• A variable may be assigned using a so called ”aggregate” (see page 13).
• Shared variables (see page 17) are global just as signals. Since variables do
not have the possibility to handle concurrent assignments from more than one
process, as signals can, shared variables are to be avoided.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
36
Copyright © 1997-2000 HARDI Electronics AB
Sequential statements
Signal assignment
LRM
Syntax
§ 8.4, 9.5
signal-assignment-statement –›
[ label ‘:’ ] ( signal-name | signal-aggregate ) ‘<=’ [ delay-mechanism ]
waveform ‘;’
delay-mechanism –› transport | [ reject time-expression ] inertial
waveform –› waveform-element { ‘,’ waveform-element } | unaffected
waveform-element –› ( value-expression | null ) [ after time-expression ]
Examples
ENTITY Design IS
PORT(externalSignal : OUT INTEGER);
END ENTITY Design;
ARCHITECTURE Behave OF Design IS
SIGNAL internalSignal : REAL;
BEGIN
externalSignal <= INTEGER(internalSignal);
...
END ARCHITECTURE Behave;
SIGNAL a : INTEGER := 0;
...
PROCESS
BEGIN
First : a <= a + 2;
Second: a <= a + 4;
Final : a <= a - 3;
WAIT FOR 5 ns;
REPORT INTEGER’IMAGE(a); -- a = -3 (i.e. 0 - 3)
END PROCESS;
s1 <= INERTIAL s AFTER 10 ns;
s2 <= REJECT 5 ns INERTIAL s AFTER 10 ns;
s3 <= TRANSPORT s AFTER 10 ns;
Comments
• A signal assignment immediately puts a value in the signal’s queue, but its driver
is updated first when the process finishes its execution, i.e. when it reaches a
WAIT statement or reaches the final line (when using a sensitivity list).
• A signal can be assigned the value of a variable and vice versa.
• The expression in the signal assignment may be arbitrarily complex and for
example include subprogram calls.
• A signal may be assigned using a so called ”aggregate” (see page 13).
• TRANSPORT generates a transmission delay of a signal.
• REJECT specifies pulses to be filtered (must be combined with INERTIAL).
• INERTIAL both filters and delays. INERTIAL is default.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
37
Concurrent and sequential statements
Sequential and concurrent statements
ASSERT/REPORT
Syntax
LRM
§ 8.2, 8.3, 9.4
assertion-statement –›
[ label ‘:’ ] [ postponed* ] assert boolean-expression [ report string-expression ]
[ severity expression ] ‘;’
report-statement –›
[ label ‘:’ ] report string-expression [ severity expression ] ‘;’
*
postponed is only allowed in a concurrent ASSERT statement
Examples
ARCHITECTURE Behave OF Design IS
BEGIN
PROCESS
BEGIN
ASSERT a = b -- sequential ASSERT
REPORT “a and b are not equal”
SEVERITY WARNING;
WAIT ON a, b;
REPORT ”WAIT was just passed”;
END PROCESS;
Control: POSTPONED ASSERT a = 12 -- Concurrent ASSERT
REPORT “a is not 12”;
END ARCHITECTURE Behave;
ASSERT ...
REPORT ”xxx”; -- The ASSERT statement ends here!
REPORT ”yyy” -- This line has nothing to do with ASSERT
SEVERITY NOTE;
-- NOTE defined for the second REPORT
ASSERT ...
REPORT ”xxx” & ”yyy” -- Here both REPORT and SEVERITY are
SEVERITY FAILURE; -- connected to ASSERT
Comments
• With an ASSERT statement a logical expression is claimed to be true. If it is false
the rest of the ASSERT statement is executed.
• SEVERITY has four possible values – NOTE, WARNING, ERROR and FAI-
LURE (see page 7, 57). In most simulators it is possible to set at which severity
level the simulation shall be stopped.
• ASSERT has default severity level ERROR while REPORT has NOTE.
• ASSERT is both a sequential and a concurrent statement while REPORT only is
a sequential statement. However a concurrent ASSERT statement may include a
REPORT statement.
• When using REPORT it is convenient to concatanate text strings using ‘&’.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ... Concurrent Assert
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END
CONFIGURATION Conf;
Conc. Assert
Concurrent Assert
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
Assert,
... ... ...
Assert, Report
Assert, Report
Report
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
38
Copyright © 1997-2000 HARDI Electronics AB
Sequential and concurrent statements
Subprogram call
LRM
Syntax
§ 7.3.3, 8.6, 9.3
function-call –› function-name [ ‘(’ parameter-association-list ‘)’ ]
procedure-call-statement –›
[ label ‘:’ ] [ postponed* ] procedure-name [ ‘(’ parameter-association-list ‘)’ ] ‘;’
parameter-association-list –›
[ formal-part ‘=>’ ] actual-part { ‘,’ [ formal-part ‘=>’ ] actual-part }
*
postponed is only allowed in a concurrent function call
Examples
ENTITY Design IS
PORT(d, clk : IN BIT; q : OUT BIT);
BEGIN
PeriodCheck(clk); -- Passive procedure call
END ENTITY Design;
-- This function adds two arrays
FUNCTION ”+”(a,b : MyArray) RETURN MyArray IS
BEGIN
...
END FUNCTION ”+”;
SIGNAL d1, d2, sum : MyArray;
...
sum <= d1 + d2; -- The function ”+” above is called
PROCEDURE Add(a,b : IN MyArray; sum : OUT MyArray) IS
BEGIN
...
END PROCEDURE Add;
Add(data1,data2,sum); -- Positional assoc.
Add(sum => sum, a => data1, b => data2); -- Named association
outData := AFunction(x,3.14,16#02AE#);
Comments
• A subprogram is called via its name. In the call actual parameters can be associated with the formal parameters declared in the subprogram. The association may
be done named or positional where positional is preferable since the order of the
parameters then does not impact the association.
• It is permitted to call passive procedures in the statement part of an entity, i.e.
procedures not assigning signals. This is useful when verifying timing for ports
declared in the entity. If any parameter is modified, the procedure is called.
• A concurrent subprogram call is executed whenever an input signal gets a new
value.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END
CONFIGURATION Conf;
Passive
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
39
Concurrent statements
Concurrent statements
PROCESS
Syntax
LRM
§ 9.2
process-statement –›
[ process-label ‘:’ ] [ postponed ] process [ ‘(’ sensitivity-list ‘)’ ] [ is ]
{subprogram-decl. | subprogram-body | type-decl. | subtype-decl. |
constant-decl. | variable-decl. | file-decl. | alias-decl. | attribute-decl. |
attribute-spec. | use-clause | group-template-decl. | group-decl. }
begin
{ sequential-statement }
end [ postponed ] process [ process-label ] ‘;’
Examples
ARCHITECTURE Behave OF Design IS
BEGIN
FlipFlop: PROCESS(reset,clk)
BEGIN
IF reset = ‘1’ THEN
q <= ‘0’;
ELSIF clk’EVENT AND clk = ‘1’ THEN
q <= d;
END IF;
END PROCESS FlipFlop;
END ARCHITECTURE Behave;
-- These two processes are equivalent
PROCESS PROCESS(s)
BEGIN BEGIN
REPORT ”s has a new value”; REPORT ”s has a new value”;
WAIT ON s; END PROCESS;
END PROCESS;
Comments
• A PROCESS holds a number of sequential statements and executes parallell
towards its environment.
• A PROCESS functions as an eternal loop. It must include at least one WAIT sta-
tement (see page 29) or a sensitivity list that specifies when the PROCESS shall
execute its sequential statements.
• A sensitivity list is equivalent to a WAIT ON statement placed as the final line in
the PROCESS. All sequential statements will execute once at simulation startup
in such processes and after that the processes will suspend.
• POSTPONED defines that the PROCESS shall be executed as the final delta at a
specific occasion.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END
CONFIGURATION Conf;
Passive
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
40
Copyright © 1997-2000 HARDI Electronics AB
Concurrent statements
WHEN
LRM
Syntax
§ 9.5.1
conditional-signal-assignment-statement –›
[ label ‘:’ ] [ postponed ] ( signal-name | signal-aggregate ) ‘<=’
[ guarded ] [ delay-mechanism ]
{ waveform when boolean-expression else }
waveform [ when boolean-expression ] ‘;’
delay-mechanism –› transport | [ reject time-expression ] inertial
waveform –› waveform-element { ‘,’ waveform-element } | unaffected
waveform-element –› ( value-expression | null ) [ after time-expression ]
Examples
-- This architecture contains three processes. ”One” is an
-- ordinary process including a sequential signal assignment
-- while ”Two” and ”Three” are concurrent signal assignments
ARCHITECTURE Behave OF Design IS
BEGIN
One: PROCESS(data)
BEGIN
outputSignal <= data;
END PROCESS One;
Two: s <= ‘1’
WHEN sel = ”00” ELSE
UNAFFECTED WHEN sel = ”11” ELSE
‘0’;
Three: s2 <= REJECT 3 ns INERTIAL d AFTER 5 ns;
END ARCHITECTURE Behave;
MyBlock: BLOCK(en = ‘1’)
BEGIN
Latch: q <= GUARDED d;
END BLOCK MyBlock;
Comments
• A concurrent signal assignment is placed directly in an ARCHITECTURE or in a
BLOCK without using a PROCESS.
• A concurrent signal assignment may preferably be named with a label. This label
simplifies simulation since the assignment then can be identified just as a named
PROCESS.
• The WHEN statement is the concurrent equivalent to the sequential IF statement.
• UNAFFECTED is new to VHDL’93 and may be used to specify that a signal
shall be left unaffected at a specific occasion, i.e. to keep its previous value.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
41
Concurrent statements
SELECT
Syntax
LRM
§ 9.5.2
selected-signal-assignment-statement –›
[ label ‘:’ ] [ postponed ] with expression select
( signal-name | signal-aggregate ) ‘<=’ [ guarded ] [ delay-mechanism ]
{ waveform when choices ‘,’ } waveform when choice { | choice } ‘;’
delay-mechanism –› transport | [ reject time-expression ] inertial
waveform –› waveform-element { ‘,’ waveform-element } | unaffected
waveform-element –› ( value-expression | null ) [ after time-expression ]
choice –› simple-expression | discrete-range | element-name-identifier | others
Examples
ARCHITECTURE Behave OF Design IS
BEGIN
Choose: WITH sel SELECT
s <= ‘1’
WHEN ”00”,
UNAFFECTED WHEN ”11”,
‘0’ WHEN OTHERS;
END ARCHITECTURE Behave;
Comments
• A concurrent signal assignment is placed directly in an ARCHITECTURE or in a
BLOCK without using a PROCESS.
• A concurrent signal assignment may preferably be named with a label. This label
simplifies simulation since the assignment then can be identified just as a named
PROCESS.
• The SELECT statement is the concurrent equivalent to the sequential CASE
statement.
• UNAFFECTED is new to VHDL’93 and may be used to specify that a signal
shall be left unaffected at a specific occasion, i.e. to keep its previous value.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
42
Copyright © 1997-2000 HARDI Electronics AB
Concurrent statements
BLOCK
LRM
Syntax
§ 9.1
block-statement –› block-label ‘:’ block [ ‘(’ guard-expression ‘)’ ] [ is ]
[ generic-clause [ generic-map ‘;’ ] ]
[ port-clause [ port-map ‘;’ ] ]
begin
{ subprog.-decl. | subprog.-body | type/subtype-decl. | constant-decl. | signal decl. | shared-variable-decl. | file-decl. | alias-decl. | component-decl. | attribute decl. | attribute-spec. | config.-spec. | use-clause | group-temp.-decl. | group-decl.}
end block [ block-label ] ‘;’
Examples
ARCHITECTURE Behave OF Design IS
CONSTANT holdTime : TIME := 5 ns;
SIGNAL output : BIT;
BEGIN
Block1: BLOCK(en = ‘1’)
GENERIC t : TIME;
GENERIC MAP(t => holdTime);
PORT(d : IN BIT;
q : OUT BIT);
PORT MAP(d => data, q => output);
BEGIN
q <= GUARDED d AFTER t;
END BLOCK Block1;
END ARCHITECTURE Behave;
OneBlock: BLOCK(en = ‘1’)
BEGIN
Latch: q <= GUARDED d;
END BLOCK OneBlock;
Comments
• A BLOCK has two purposes – to introduce a structure in the design and to be
used in combination with guarded signals.
• A BLOCK may have generic parameters and a port list just as an ENTITY. It is
however most common to use components when structure is desired. The advantage of components is that it exists powerful methods to instantiate and configure
them (see pages 28, 46-50).
• Declarations inside a BLOCK are local in the BLOCK.
• A BLOCK must be named by a label.
• It is possible to declare a BLOCK inside another BLOCK. That creates a structure in the design.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
43
Generic parameters and GENERATE
Generic parameters and generate
GENERIC/GENERIC MAP
LRM
Syntax
§1.1.1.1,5.2.1.2
generic-clause –› generic ‘(’ generic-interface-list ‘)’ ‘;’
generic-map –› generic map ‘(’ generic-association-list ‘)’ ‘;’
interface-list –› interface-element { ‘;’ interface-element }
interface-element –›interface-constant-declaration | interface-signal-declaration |
interface-variable-declaration | interface-file-declaration
association-list –›
[ formal-part ‘=>’ ] actual-part
{ ‘,’ [ formal-part ‘=>’ ] actual-part }
Examples
ENTITY LargeFlipFlop IS
GENERIC(n : NATURAL;
t : TIME);
PORT(d : IN BIT_VECTOR(n DOWNTO 0);
clk : IN BIT;
q : OUT BIT_VECTOR(n DOWNTO 0));
END ENTITY LargeFlipFlop;
ARCHITECTURE Behave OF LargeFlipFlop IS
BEGIN
q <= d AFTER t WHEN (clk’EVENT AND clk = ‘1’);
END ARCHITECTURE Behave;
-- The entity LargeFlipFlop may be
ARCHITECTURE Behave OF Top IS
COMPONENT LargeFlipFlop IS
... -- The same declaration as
END COMPONENT LargeFlipFlop;
BEGIN
C1 : LargeFlipFlop GENERIC MAP(n
PORT MAP(d =>
END ARCHITECTURE Behave;
instantiated like this:
in the ENTITY LargeFlipFlop
=> 5, t => 12 ns)
dtop, clk => clk, q => qtop);
Comments
• Generic parameters are used to create parameterizable units in a design. First
when the unit shall be used the parameters must get values. Generic parameters
may for example be used to define bus widths and delay parameters. Delay parameters are useful when generating backannotated VHDL files from synthesis and
Place&Route tools.
• Generic parameters are ”connected” to values using a GENERIC MAP that
functions just as a PORT MAP does for signals (see page 47).
• A GENERIC MAP may exist in a component instantiation (see page 47), in a
configuration declaration (see page 50) or in a BLOCK instantiation (see page
43). The generic parameters may also be assigned values in the simulator or in
the synthesis tool.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
GENERIC
... ... BEGIN
GENERIC
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
&
MAP
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION
Conf OF Ent IS
GENERIC
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
44
Copyright © 1997-2000 HARDI Electronics AB
Generic parameters and generate
GENERATE
LRM
Syntax
§ 9.7
generate-statement –› generate-label ‘:’
( for identifier in discrete-range | if boolean-expression ) generate
[ subprog.-decl. | subprog.-body | type/subtype-decl. | constant-decl. | signal decl. | shared-variable-decl. | file-decl. | alias-decl. | component-decl. | attribute decl. | attribute-spec. | config.-spec. | use-clause | group-temp.-decl. | group-decl.
begin ]
{ concurrent-statement }
end generate [ generate-label ] ‘;’
Examples
ENTITY FlipFlop IS
PORT(d, clk : IN BIT;
q : OUT BIT);
END ENTITY FlipFlop;
ARCHITECTURE Behave OF FlipFlop IS ...
ENTITY LargeFlipFlop IS
GENERIC(n : NATURAL);
PORT(d : IN BIT_VECTOR(n DOWNTO 0);
clk : IN BIT;
q : OUT BIT_VECTOR(n DOWNTO 0));
END ENTITY LargeFlipFlop;
ARCHITECTURE Behave OF LargeFlipFlop IS
COMPONENT FlipFlop ... -- The same as in the ENTITY FlipFlop
BEGIN
Build: FOR i IN d’RANGE GENERATE
FOR ALL : FlipFlop USE ENTITY WORK.FlipFlop(Behave);
BEGIN
D : FlipFlop PORT MAP(d => d(i), clk => clk, q => q(i));
END GENERATE Build;
END ARCHITECTURE Behave;
Comments
• GENERATE is used to conditionally create processes. FOR GENERATE is
useful to create a number of copies of processes, while IF GENERATE is useful
when a part of a design shall be excluded during simulation or synthesis.
• The GENERATE statement must be named by a label. This label can be addressed in a configuration declaration (see page 50) and by that parameters in the
GENERATE statement can be modified or completed.
• A configuration specification (see page 49) for components in a GENERATE
statement must be placed between GENERATE and BEGIN in the statement (see
example above).
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
45
Components
Components
Component declaration
Syntax
LRM
§ 4.5
component-declaration –›
component identifier [ is ]
[ local-generic-clause ]
[ local-port-clause ]
end component [ component-name-identifier ] ‘;’
Examples
COMPONENT LargeFlipFlop IS
GENERIC(n : NATURAL;
t : TIME);
PORT(d : IN BIT_VECTOR(n DOWNTO 0);
clk : IN BIT;
q : OUT BIT_VECTOR(n DOWNTO 0));
END COMPONENT LargeFlipFlop;
Comments
• A COMPONENT declares an ”empty socket”. There is no specification of what
to be placed in the ”socket”, i.e. which ENTITY and ARCHITECTURE that will
specify the functionality.
• Components are used to achieve a structure in a design. The number of hierarchical levels is unlimited.
• Three steps are performed when working with components – component declaration, component instantiation (see page 47) and component configuration (see
page 48-50). In VHDL’93 it is also possible to directly instantiate an ENTITY, a
so called direct instantiation (see page 47). This method is however not recommended since the design then loses in reuseability.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
46
Copyright © 1997-2000 HARDI Electronics AB
Components
Component instantiation
LRM
Syntax
§ 9.6
component-instantiation-statement –›
instantiation-label ‘:’ instantiated-unit [ generic-map ] [ port-map ] ‘;’
instantiated-unit –›
[ component ] component-name |
entity entity-name [ ‘(’ architecture-identifier ‘)’ ] |
configuration configuration-name
Examples
ENTITY LargeFlipFlop IS
GENERIC(n : NATURAL; t : TIME);
PORT(d : IN BIT_VECTOR(n DOWNTO 0);
clk : IN BIT;
q : OUT BIT_VECTOR(n DOWNTO 0));
END ENTITY LargeFlipFlop;
ARCHITECTURE Behave OF LargeFlipFlop IS
...
ENTITY Design IS ...
ARCHITECTURE Behave OF Design IS
COMPONENT LargeFlipFlop IS
GENERIC(n : NATURAL; t : TIME);
PORT(d : IN BIT_VECTOR(n DOWNTO 0);
clk : IN BIT;
q : OUT BIT_VECTOR(n DOWNTO 0));
END COMPONENT LargeFlipFlop;
BEGIN
C1 : LargeFlipFlop GENERIC MAP(t => 12 ns, n => 5)
PORT MAP(clk => clk, q => q1, d => d1);
C2 : ENTITY WORK.LargeFlipFlop(Behave) GENERIC MAP(7, 15 ns)
PORT MAP(d2, clk, q2);
END ARCHITECTURE Behave;
Comments
• A component instantiation specifies how a component, an entity (only in
VHDL’93) or a configuration declaration is connected in a design. It is not
recommended to directly instantiate entities, so called direct instantiation (’C2’
above), since the design then loses in reuseability.
• Components are used to achieve structure in a design. The number of hierarchical
levels is unlimited. Three steps are performed when working with components
– component declaration (see page 46), component instantiation and component
configuration (see page 48-50).
• A PORT MAP connects ports from inside and out (component port => signal).
• Using OPEN specifies that a port shall be unconnected.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
47
Components
Default configuration
Syntax
LRM
§ 5.2.2
(No syntax)
Examples
ENTITY LargeFlipFlop IS
GENERIC(n : NATURAL; t : TIME);
PORT(d : IN BIT_VECTOR(n DOWNTO 0);
clk : IN BIT;
q : OUT BIT_VECTOR(n DOWNTO 0));
END ENTITY LargeFlipFlop;
ARCHITECTURE Behave OF LargeFlipFlop IS ...
ENTITY Design IS ...
ARCHITECTURE Behave OF Design IS
COMPONENT LargeFlipFlop IS
GENERIC(n : NATURAL; t : TIME);
PORT(d : IN BIT_VECTOR(n DOWNTO 0);
clk : IN BIT;
q : OUT BIT_VECTOR(n DOWNTO 0));
END COMPONENT LargeFlipFlop;
BEGIN
-- The entity ”LargeFlipFlop” and its architecture ”behave”
-- will be used for C1 provided that they are compiled to WORK
-- and that ”behave” is the last compiled architecture
C1 : LargeFlipFlop GENERIC MAP(n => 5, t => 12 ns)
PORT MAP(d1, clk, q1);
END ARCHITECTURE Behave;
Comments
• A default configuration implies that the simulator or the synthesis tool automati-
cally will connect a COMPONENT to an ENTITY. This requires that they match
perfectly regarding names, port names, port types, port directions, generic parameter names and generic parameter types. The latest compiled ARCHITECTURE
for the ENTITY is used.
• The advantages by using a default configuration are that it is simple (no explicit
configuration is needed) and that it may be overwritten by a configuration
declaration (see page 50). The disadvantages are that the ENTITY must match
the COMPONENT perfectly and that it is not unambigously defined which
ARCHITECTURE that will be used.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
48
Copyright © 1997-2000 HARDI Electronics AB
Components
Configuration specification
LRM
Syntax
§ 5.2
configuration-specification –›
for ( instantiation-label { ‘,’ instantiation-label } | others | all ) ‘:’
component-name [ use entity-aspect ] [ generic-map ] [ port-map ] ‘;’
Examples
ENTITY LargeFlipFlop IS
GENERIC(t : TIME; n : NATURAL);
PORT(clk
: IN BIT;
d : IN BIT_VECTOR(n DOWNTO 0);
q, qinv : OUT BIT_VECTOR(n DOWNTO 0));
END ENTITY LargeFlipFlop;
ARCHITECTURE Behave OF LargeFlipFlop IS ...
ENTITY Design IS ...
ARCHITECTURE Behave OF Design IS
COMPONENT LargeFlipFlop IS
GENERIC(n : NATURAL; t : TIME);
PORT(d : IN BIT_VECTOR(n DOWNTO 0);
clk : IN BIT;
q : OUT BIT_VECTOR(n DOWNTO 0));
END COMPONENT LargeFlipFlop;
FOR C1 : LargeFlipFlop USE ENTITY WORK.LargeFlipFlop(Behave)
GENERIC MAP(12 ns, 5) PORT MAP(clk, d, q, OPEN);
FOR OTHERS : LargeFlipFlop USE ...
BEGIN
C1 : LargeFlipFlop GENERIC MAP(n => 5, t => 12 ns) PORT MAP ...
C2 : LargeFlipFlop GENERIC MAP(...) PORT MAP (...);
END ARCHITECTURE Behave;
Comments
• A configuration specification connects a specific ENTITY and a specific ARCHI-
TECTURE to a COMPONENT. The configuration specifies in detail how the
connection shall be and that excludes the demand of perfect match. OPEN in a
PORT MAP defines that a port shall be unconnected.
• The configuration specification is the mid alternative among the three possible
configurations (see pages 48, 50). It is more powerful than a default configuration
since the demand of perfect match between the ENTITY and the COMPONENT
is excluded. It may on the other hand not configure sub blocks in the design hierarchy as a configuration declaration can. Modifications imply a recompilation of
the whole architecture and since the component is locked to a specific entity/architecture pair it is not well suited for multilevel simulations.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
Copyright © 1997-2000 HARDI Electronics AB
49
Components
Configuration declaration
Syntax
LRM
§ 1.3
configuration-declaration –› configuration identifier of entity-name is
{ use-clause | attribute-specification | group-declaration }
block-configuration
end [ configuration ] [ configuration-name-identifier ] ‘;’
block-configuration –›for ( architecture-name | block-statement-label |
generate-statement-label [ ‘(’ index-specification ‘)’ ] ) { use-clause }
{ block-configuration | component-configuration }
end for ‘;’
Examples
CONFIGURATION MyConfiguration OF Design IS
FOR Behave
FOR C1 : LargeFlipFlop USE ENTITY WORK.LargeFlipFlop(Behave)
GENERIC MAP(7, 20 ns) PORT MAP(...);
END FOR;
FOR OTHERS : LargeFlipFlop USE ENTITY
WORK.LargeFlipFlop(Structure);
FOR Structure
FOR A1 : SubComponent USE ENTITY ...
END FOR;
FOR OTHERS : SubComponent USE CONFIGURATION ...
END FOR;
END FOR;
END FOR;
END FOR;
END CONFIGURATION MyConfiguration;
Comments
• A configuration declaration is a separate design unit in VHDL (see page 28).
It is the most powerful of the three possible configurations (see pages 48-49)
and it can modify previously performed configuration specifications (so called
incremental binding).
• The configuration declaration is well suited for multilevel simulations since it
can configure sub blocks in a design. It can also modify generic parameters, e.g.
timing parameters, and also configure GENERATE statements (see page 45).
• The disadvantage with the configuration declaration is its complicated syntax.
• A configuration declaration connects an entire design and is therefore compiled
as the final design unit.
Placement
Blk:BLOCK
PACKAGE Pack IS PACKAGE BODY Pack IS ...
... ... BEGIN
END PACKAGE Pack; END PACKAGE BODY Pack; ...
END BLOCK Blk;
ENTITY Ent IS ARCHITECTURE Arc OF Ent IS ... ... CONFIGURATION Conf OF Ent IS
BEGIN BEGIN ...
... ... END CONFIGURATION Conf;
END ENTITY Ent; END ARCHITECTURE Arc;
Proc:PROCESS(...) PROCEDURE P(...) IS FUNCTION F(...) RETURN Tp IS
... ... ...
BEGIN BEGIN BEGIN
... ... ...
END PROCESS Proc; END PROCEDURE P; END FUNCTION F;
50
Copyright © 1997-2000 HARDI Electronics AB
Predefined attributes
Predefined attributes
LRM
§ 14.1
Attributes on types
T’BASE
Gives the base type of a type T. Can only be used as a
prefix for another attribute.
Example:
SUBTYPE MyNat IS NATURAL RANGE 5 TO 15;
MyNat’BASE’LOW = -2_147_483_647 (=INTEGER’LOW)
T’LEFT
Gives the leftmost value in the type T.
Example:
T’RIGHT
Gives the rightmost value in the type T.
Example:
TYPE State IS (reset,start,count);
State’LEFT = reset
TYPE State IS (reset,start,count);
State’RIGHT = count
T’HIGH
Gives the largest value in the type T.
Example:
SUBTYPE MyNat IS NATURAL RANGE 5 TO 15;
MyNat’HIGH = 15
T’LOW
Gives the smallest value in the type T.
Example:
SUBTYPE MyNat IS NATURAL RANGE 5 TO 15;
MyNat’LOW = 5
T’ASCENDING Returns a value of the type BOOLEAN that is TRUE if
the type T is defined with an ascending range.
Example:
SUBTYPE MyNat IS NATURAL RANGE 5 TO 15;
MyNat’ASCENDING = TRUE
T’IMAGE(X)* Converts the value X, that is of the type or subtype T,
to a text string. T must be a scalar type, i.e. an integer, a
real, a physical type or an enumerated type.
Example:
TYPE State IS (reset,start,count);
State’IMAGE(start) = ”start”
T’VALUE(X)* Converts the text string X to a value of the type T. T
must be a scalar type, i.e. an integer, a real, a physical
type or an enumerated type.
Example:
TYPE State IS (reset,start,count);
State’VALUE(”reset”) = reset
T’POS(X)
Returns the position number of X within the type T.
Example:
*
TYPE State IS (reset,start,count);
State’POS(start) = 1
New to VHDL’93
Copyright © 1997-2000 HARDI Electronics AB
51
Predefined attributes
T’VAL(X)
Returns the value on position X in the type T.
Example:
TYPE State IS (reset,start,count);
State’VAL(0) = reset
T’SUCC(X)
Returns the value, of the type T, with the position number one greater than that of the parameter X.
Example:
T’PRED(X)
Returns the value, of the type T, with the position number one less than that of the parameter X.
Example:
TYPE MyInteger IS RANGE 5 DOWNTO -5;
MyInteger’SUCC(0) = 1
TYPE MyInteger IS RANGE 5 DOWNTO -5;
MyInteger’PRED(0) = -1
T’LEFTOF(X) Returns the value to the left of the value X in the range
of the type T.
Example:
TYPE MyInteger IS RANGE 5 DOWNTO -5;
MyInteger’LEFTOF(0) = 1
T’RIGHTOF(X) Returns the value to the right of the value X in the range
of the type T.
Example:
TYPE MyInteger IS RANGE 5 DOWNTO -5;
MyInteger’RIGHTOF(0) = -1
Attributes on arrays
(All attributes on arrays are valid for both types and objects)
A’HIGH[(N)]
Returns the numerical largest index limit in the array A
for its index range N. N may be omitted and its default
value is 1.
Example:
TYPE M IS ARRAY (0 TO 3, 2 DOWNTO 1) OF BIT;
VARIABLE matrix : M;
M’HIGH = 3
matrix’HIGH(2) = 2
A’LOW[(N)]
Returns the numerical smallest index limit in the array A
for its index range N. N may be omitted and its default
value is 1.
Example:
TYPE M IS ARRAY (0 TO 3, 2 DOWNTO 1) OF BIT;
VARIABLE matrix : M;
M’LOW = 0
matrix’LOW(2) = 1
A’LEFT[(N)]
Returns the left index limit for the array A for its index
range N. N may be omitted and its default value is 1.
Example:
52
TYPE M IS ARRAY (0 TO 3, 2 DOWNTO 1) OF BIT;
VARIABLE matrix : M;
M’LEFT = 0
matrix’LEFT(2) = 2
Copyright © 1997-2000 HARDI Electronics AB
Predefined attributes
A’RIGHT[(N)] Returns the right index limit for the array A for its index
range N. N may be omitted and its default value is 1.
Example:
TYPE M IS ARRAY (0 TO 3, 2 DOWNTO 1) OF BIT;
VARIABLE matrix : M;
M’RIGHT = 3
matrix’RIGHT(2) = 1
A’RANGE[(N)] Returns the index range as a RANGE for the array A
for its index range N. N may be omitted and its default
value is 1.
Example:
TYPE M IS ARRAY (0 TO 3, 2 DOWNTO 1) OF BIT;
VARIABLE matrix : M;
M’RANGE = 0 TO 3
matrix’RANGE(2) = 2 DOWNTO 1
A’REVERSE_RANGE[(N)]
Returns the index range as a RANGE, but with opposite
direction, for the array A for its index range N. N may
be omitted and its default value is 1.
Example:
TYPE M IS ARRAY (0 TO 3, 2 DOWNTO 1) OF BIT;
VARIABLE matrix : M;
M’REVERSE_RANGE = 3 DOWNTO 0
matrix’REVERSE_RANGE(2) = 1 TO 2
A’LENGTH[(N)]
Returns the number of elements in the array A for its
index range N. N may be omitted and its default value is
1.
Example:
TYPE M IS ARRAY (0 TO 3, 2 DOWNTO 1) OF BIT;
VARIABLE matrix : M;
M’LENGTH = 4
matrix’LENGTH(2) = 2
A’ASCENDING[(N)]*
Returns a value of the type BOOLEAN that is TRUE
if the index range N for array A is ascending. N may be
omitted and its default value is 1.
Example:
TYPE M IS ARRAY (0 TO 3, 2 DOWNTO 1) OF BIT;
VARIABLE matrix : M;
M’ASCENDING = TRUE
matrix’ASCENDING(2) = FALSE
Attributes on signals
S’STABLE[(T)] Creates a new signal of the type BOOLEAN that returns
TRUE as long as the signal S does not change its value.
The signal gets FALSE when S changes value and is
FALSE during the time T. T may be omitted and its
default value i 0 ns.
S’DELAYED[(T)]
*
New to VHDL’93
Copyright © 1997-2000 HARDI Electronics AB
53
Predefined attributes
S’QUIET[(T)]
Functions exactly as ‘STABLE but reacts on all updates
of S from its driver queue, also when the signal is assigned the value it already has.
S’DELAYED[(T)]
Creates a copy of the signal S delayed the time T. T may
be omitted and its default value is 0 ns, i.e. exactly S.
S’TRANSACTION
Creates a new signal of the type BIT that changes value
every time the signal S gets a new value from its driver
queue, i.e. also when it gets the same value as it already
has. The initial value of the new signal is not specified.
S’
A function of the type BOOLEAN that returns TRUE
during exactly one delta cycle when the signal S gets a
new value.
S’ACTIVE
Functions exactly as ‘EVENT but reacts on all updates
of S from its driver queue, also when the signal is assigned the value it already has.
S’LAST_EVENT
A function of the type TIME returning the time since the
last change of the value of the signal S.
S’LAST_ACTIVE
A function of the type TIME returning the time since the
the last update of the signal S.
S’LAST_VALUE
A function of the same base type as S returning the
value the signal S had before its last value change.
S’DRIVING*
A function of the type BOOLEAN returning TRUE if
the driver for the signal S is on.
S’DRIVING_VALUE*
A function of the same type as S returning the current
value in the driver for the signal S in the current process.
Attributes on named entities
E’SIMPLE_NAME*
*
Returns the name, in a text string with lower-case letters, of a named entity.
New to VHDL’93
54
Copyright © 1997-2000 HARDI Electronics AB
Predefined attributes
E’INSTANCE_NAME*
Returns the hierarchical path including instances higher
in the hierarchy, in a string with lower-case letters, to a
named entity.
E’PATH_NAME*
Returns the hierarchical path not including instances
higher in the hierarchy, in a string with lower-case letters, to a named entity.
*
Example:
ENTITY E IS
...
END ENTITY E;
ARCHITECTURE A OF E IS
BEGIN
P: PROCESS(clock)
VARIABLE inVar : NATURAL RANGE 0 TO 255;
BEGIN
...
-- inVar’SIMPLE_NAME = ”invar”
-- inVar’INSTANCE_NAME = ”:e(a):p:invar”
-- inVar’PATH_NAME = ”:e:p:invar”
END PROCESS P;
END ARCHITECTURE A;
New to VHDL’93
Copyright © 1997-2000 HARDI Electronics AB
55
IEEE
IEEE
There is a number of predefined packages in VHDL. All packages standardized by IEEE are described in this chapter. Further there are a number of non
standardized packages, e.g. STD_LOGIC_ARITH, STD_LOGIC_SIGNED,
NUMERIC_SIGNED, STD_LOGIC_UNSIGNED and NUMERIC_UNSIGNED, but they are not recommended to be used since they are not
standardized and may differ between different tools.
VHDL standards
VHDL is built upon a number of standards from IEEE:
• IEEE std 1076-1987 The first standard of VHDL. It is commonly abbreviated VHDL’87.
• IEEE std 1076-1993 The second standard of VHDL. It is commonly
abbreviated VHDL’93.
• IEEE std 1164-1993 The package STD_LOGIC_1164 (see page 58).
Includes hardware related types and conversion
functions.
• IEEE std 1076a
Intended to improve the usage of shared variables
(see page 17).
• IEEE std 1076.1
VHDL-AMS, analog extensions.
• IEEE std 1076.2
Mathematical packages (see page 63-65). Divided
into one package for real numbers and one for
imaginary numbers.
• IEEE std 1076.3
Describes for example types and operators intended
for synthesis.
• IEEE std 1076.4
VITAL (VHDL Initiative Towards ASIC Libraries).
For example used to specify timing parameters for
backannotated simulation.
• IEEE std 1076.5
Guidelines for modeling of libraries in VHDL.
• IEEE std 1076.6
Defines the part of VHDL intended for RTL synthesis.
Predefined packages
LRM
STANDARD
§ 14.2
The standard of VHDL. Is precompiled into the library ”STD” (accessed via USE STD.
STANDARD.ALL that is implicitely declared).
package standard is type BOOLEAN is (FALSE,TRUE); type bit is (‘0’, ‘1’); type character is (
nul, soh, stx, etx, eot, enq, ack, bel,
BS, HT, LF, VT, FF, CR, SO, SI,
DLE, DC1, DC2, DC3, DC4, NAK, SYN, ETB,
can, em, sub, esc, fsp, gsp, rsp, usp, ‘ ‘,
‘(‘,
‘0’,
‘8’,
‘!’,
‘)’,
‘1’,
‘9’,
‘”’,
‘*’,
‘2’,
‘:’,
‘#’,
‘+’,
‘3’,
‘;’,
‘$’,
‘,’,
‘4’,
‘<’,
‘%’,
‘-’,
‘5’,
‘=’,
‘&’,
‘.’,
‘6’,
‘>’,
‘’’,
‘/’,
‘7’,
‘?’,
‘@’,
‘H’,
‘P’,
‘X’,
‘A’,
‘I’,
‘Q’,
‘Y’,
‘B’,
‘J’,
‘R’,
‘Z’,
‘C’,
‘K’,
‘S’,
‘[‘,
‘D’,
‘L’,
‘T’,
‘\’,
‘E’,
‘M’,
‘U’,
‘]’,
‘F’,
‘N’,
‘V’,
‘^’,
‘G’,
‘O’,
‘W’,
‘_’,
56
Copyright © 1997-2000 HARDI Electronics AB
IEEE
‘`’,
‘h’,
‘p’,
‘x’,
‘a’,
‘i’,
‘q’,
‘y’,
‘b’,
‘j’,
‘r’,
‘z’,
‘c’,
‘k’,
‘s’,
‘{‘,
‘d’,
‘l’,
‘t’,
‘|’,
‘e’,
‘m’,
‘u’,
‘}’,
‘f’,
‘n’,
‘v’,
‘~’,
‘g’,
‘o’,
‘w’,
del,
c128, c129, c130, c131, c132, c133, c134, c135,
c136, c137, c138, c139, c140, c141, c142, c143,
c144, c145, c146, c147, c148, c149, c150, c151,
c152, c153, c154, c155, c156, c157, c158, c159,
‘ ‘,
‘¨’,
‘°’,
‘¸’,
‘¡’,
‘©’,
‘±’,
‘¹’,
‘¢’,
‘ª’,
‘²’,
‘º’,
‘£’,
‘«‘,
‘³’,
‘»’,
‘¤’, ‘¥’, ‘¦’, ‘§’,
‘¬’, ‘­‘, ‘®’, ‘¯’,
‘´’, ‘µ’, ‘¶’, ‘·’,
‘¼’, ‘½’, ‘¾’, ‘¿’,
‘À’,
‘È’,
‘Ð’,
‘Ø’,
‘Á’,
‘É’,
‘Ñ’,
‘Ù’,
‘Â’,
‘Ê’,
‘Ò’,
‘Ú’,
‘Ã’,
‘Ë’,
‘Ó’,
‘Û’,
‘Ä’,
‘Ì’,
‘Ô’,
‘Ü’,
‘Å’,
‘Í’,
‘Õ’,
‘Ý’,
‘Æ’,
‘Î’,
‘Ö’,
‘Þ’,
‘Ç’,
‘Ï’,
‘×’,
‘ß’,
‘à’, ‘á’, ‘â’, ‘ã’, ‘ä’, ‘å’, ‘æ’, ‘ç’,
‘è’, ‘é’, ‘ê’, ‘ë’, ‘ì’, ‘í’, ‘î’, ‘ï’,
‘ð’, ‘ñ’, ‘ò’, ‘ó’, ‘ô’, ‘õ’, ‘ö’, ‘÷’,
‘ø’, ‘ù’, ‘ú’, ‘û’, ‘ü’, ‘ý’, ‘þ’, ‘ÿ’ );
type severity_level is (note, warning, error, failure);
type integer is range implementation_defined; type real is range implementation_defined;
type time is range implementation_defined
units fs;
ps = 1000 fs;
ns = 1000 ps;
us = 1000 ns; ms = 1000 us; sec = 1000 ms;
min = 60 sec; hr = 60 min; end units;
subtype delay_length is time range 0 fs to time’high;
impure function now return delay_length; subtype is integer range 0 to integer’high; subtype positive is integer range 1 to integer’high; type string is array (positive range <>) of character; type bit_vector is array (natural range <>) of bit; type file_open_kind is (read_mode, write_mode, append_mode);
type file_open_status is (open_ok, status_error, name_errOR,
mode_error);
attribute foreign : string;
end package standard;
LRM
TEXTIO
§ 14.3
Types and subprograms to handle text files. Is precompiled into the library ”STD (accessed via USE STD.TEXTIO.ALL).
package TEXTIO is
type LINE is access STRING;
type TEXT is file of STRING;
type SIDE is (right, left);
subtype WIDTH is natural;
file input : TEXT open read_mode is ”STD_INPUT”;
file output : TEXT open write_mode is ”STD_OUTPUT”;
procedure READLINE(file F:TEXT; L:out LINE);
procedure READ(L:inout LINE; VALUE:out BIT;
GOOD:out BOOLEAN);
procedure READ(L:inout LINE; VALUE:out BIT);
procedure READ(L:inout LINE; VALUE:out BIT_VECTOR;
GOOD:out BOOLEAN);
procedure READ(L:inout LINE; VALUE:out BIT_VECTOR);
procedure READ(L:inout LINE; VALUE:out BOOLEAN;
GOOD:out BOOLEAN);
procedure READ(L:inout LINE; VALUE:out BOOLEAN);
Copyright © 1997-2000 HARDI Electronics AB
57
IEEE
procedure READ(L:inout LINE; VALUE:out CHARACTER;
GOOD:out BOOLEAN);
procedure READ(L:inout LINE; VALUE:out CHARACTER);
procedure READ(L:inout LINE; VALUE:out INTEGER;
GOOD:out BOOLEAN);
procedure READ(L:inout LINE; VALUE:out INTEGER);
procedure READ(L:inout LINE; VALUE:out real;
GOOD:out BOOLEAN);
procedure READ(L:inout LINE; VALUE:out real);
procedure READ(L:inout LINE; VALUE:out STRING;
GOOD:out BOOLEAN);
procedure READ(L:inout LINE; VALUE:out STRING);
procedure READ(L:inout LINE; VALUE:out time;
GOOD:out BOOLEAN);
procedure READ(L:inout LINE; VALUE:out time);
procedure WRITELINE(file f:TEXT; L:inout LINE);
procedure WRITE(L:inout LINE; VALUE:in BIT;
JUSTIFIED:in SIDE := right;
FIELD:in WIDTH := 0);
procedure WRITE(L:inout LINE; VALUE:in BIT_VECTOR;
JUSTIFIED:in SIDE := right;
FIELD:in WIDTH := 0);
procedure WRITE(L:inout LINE; VALUE:in BOOLEAN;
JUSTIFIED:in SIDE := right;
FIELD:in WIDTH := 0);
procedure WRITE(L:inout LINE; VALUE:in CHARACTER;
JUSTIFIED:in SIDE := right;
FIELD:in WIDTH := 0);
procedure WRITE(L:inout LINE; VALUE:in INTEGER;
JUSTIFIED:in SIDE := right;
FIELD:in WIDTH := 0);
procedure WRITE(L:inout LINE; VALUE:in real;
JUSTIFIED:in SIDE := right;
FIELD:in WIDTH := 0;
DIGITS:in NATURAL := 0);
procedure WRITE(L:inout LINE; VALUE:in STRING;
JUSTIFIED:in SIDE := right;
FIELD:in WIDTH := 0);
procedure WRITE(L:inout LINE; VALUE:in time;
JUSTIFIED:in SIDE := right;
FIELD:in WIDTH := 0;
UNIT:in TIME := ns);
-- function ENDFILE(file F:TEXT) return BOOLEAN;
end package TEXTIO;
STD_LOGIC_1164
Hardware related, resolved types and conversion functions for them. Is precompiled
into the library ”IEEE” (accessed via USE IEEE.STD_LOGIC_1164.ALL).
package STD_LOGIC_1164 is
type STD_ULOGIC is (‘U’, -- Uninitialized
‘X’, -- Forcing Unknown
‘0’, -- Forcing 0
‘1’, -- Forcing 1
‘Z’, -- High Impedance ‘W’, -- Weak Unknown
‘L’, -- Weak 0
‘H’, -- Weak 1
‘-’ -- Don’t care);
type STD_ULOGIC_VECTOR is array (NATURAL RANGE <>) of
STD_ULOGIC;
function resolved (s : STD_ULOGIC_VECTOR) return STD_ULOGIC;
subtype STD_LOGIC is resolved STD_ULOGIC;
type STD_LOGIC_VECTOR is array (NATURAL range <>) of STD_LOGIC;
subtype
subtype
subtype
subtype
X01
X01Z
UX01
UX01Z
is
is
is
is
resolved
resolved
resolved
resolved
STD_ULOGIC
STD_ULOGIC
STD_ULOGIC
STD_ULOGIC
range
range
range
range
‘X’
‘X’
‘U’
‘U’
to
to
to
to
‘1’;
‘Z’;
‘1’;
‘Z’;
function ”and” (l:STD_ULOGIC; r:STD_ULOGIC) return UX01;
58
Copyright © 1997-2000 HARDI Electronics AB
IEEE
function
function
function
function
function
function
function
function
”nand” (l:STD_ULOGIC; r:STD_ULOGIC) return UX01;
”or” (l:STD_ULOGIC; r:STD_ULOGIC) return UX01;
”nor” (l:STD_ULOGIC; r:STD_ULOGIC) return UX01;
”xor” (l:STD_ULOGIC; r:STD_ULOGIC) return UX01;
”xnor” (l:STD_ULOGIC; r:STD_ULOGIC) return ux01;
”not” (l:STD_ULOGIC)
return UX01;
”and” (l,r:STD_LOGIC_VECTOR) return STD_LOGIC_VECTOR;
”and” (l,r:STD_ULOGIC_VECTOR)
return STD_ULOGIC_VECTOR;
function ”nand” (l,r:STD_LOGIC_VECTOR)
return STD_LOGIC_VECTOR;
function ”nand” (l,r:STD_ULOGIC_VECTOR)
return STD_ULOGIC_VECTOR;
function ”or” (l,r:STD_LOGIC_VECTOR)
return STD_LOGIC_VECTOR;
function ”or” (l,r:STD_ULOGIC_VECTOR)
return STD_ULOGIC_VECTOR;
function ”nor” (l,r:STD_LOGIC_VECTOR)
return STD_LOGIC_VECTOR;
function ”nor” (l,r:STD_ULOGIC_VECTOR)
return STD_ULOGIC_VECTOR;
function ”xor” (l,r:STD_LOGIC_VECTOR)
return STD_LOGIC_VECTOR;
function ”xor” (l,r:STD_ULOGIC_VECTOR)
return STD_ULOGIC_VECTOR;
function ”xnor” (l,r:STD_LOGIC_VECTOR)
return STD_LOGIC_VECTOR;
function ”xnor” (l,r:STD_ULOGIC_VECTOR)
return STD_ULOGIC_VECTOR;
function ”not” (l:STD_LOGIC_VECTOR)
return STD_LOGIC_VECTOR;
function ”not” (l:STD_ULOGIC_VECTOR)
return STD_ULOGIC_VECTOR;
function To_bit (s:STD_ULOGIC; xmap:BIT := ‘0’) return BIT;
function To_bitvector (s:STD_LOGIC_VECTOR ; xmap:BIT := ‘0’)
return BIT_VECTOR;
function To_bitvector (s:STD_ULOGIC_VECTOR; xmap:BIT := ‘0’)
return BIT_VECTOR;
function To_StdULogic (b:BIT) return STD_ULOGIC;
function To_StdLogicVector (b:BIT_VECTOR)
return STD_LOGIC_VECTOR;
function To_StdLogicVector (s:STD_ULOGIC_VECTOR)
return STD_LOGIC_VECTOR;
function To_StdULogicVector (b:BIT_VECTOR)
return STD_ULOGIC_VECTOR;
function To_StdULogicVector (s:STD_LOGIC_VECTOR)
return STD_ULOGIC_VECTOR;
function To_X01 (s:STD_LOGIC_VECTOR) return STD_LOGIC_VECTOR;
function To_X01 (s:STD_ULOGIC_VECTOR) return STD_ULOGIC_VECTOR;
function To_X01 (s:STD_ULOGIC)
return X01;
function To_X01 (b:BIT_VECTOR)
return STD_LOGIC_VECTOR;
function To_X01 (b:BIT_VECTOR)
return STD_ULOGIC_VECTOR;
function To_X01 (b:BIT)
return X01;
function To_X01Z (s:STD_LOGIC_VECTOR) return STD_LOGIC_VECTOR;
function To_X01Z (s:STD_ULOGIC_VECTOR) return STD_ULOGIC_VECTOR;
function To_X01Z (s:STD_ULOGIC) return X01Z;
function To_X01Z (b:BIT_VECTOR)
return STD_LOGIC_VECTOR;
function To_X01Z (b:BIT_VECTOR)
return STD_ULOGIC_VECTOR;
function To_X01Z (b:BIT)
return X01Z;
function To_UX01 (s:STD_LOGIC_VECTOR) return STD_LOGIC_VECTOR;
function To_UX01 (s:STD_ULOGIC_VECTOR) return STD_ULOGIC_VECTOR;
function To_UX01 (s:STD_ULOGIC) return UX01;
function To_UX01 (b:BIT_VECTOR) return STD_LOGIC_VECTOR;
function To_UX01 (b:BIT_VECTOR) return STD_ULOGIC_VECTOR;
function To_UX01 (b:BIT) return UX01;
function rising_edge (signal s:STD_ULOGIC) return BOOLEAN;
function falling_edge (signal s:STD_ULOGIC) return BOOLEAN;
function Is_X (s:STD_ULOGIC_VECTOR) return BOOLEAN;
function Is_X (s:STD_LOGIC_VECTOR) return BOOLEAN;
function Is_X (s:STD_ULOGIC) return BOOLEAN;
end package STD_LOGIC_1164;
Copyright © 1997-2000 HARDI Electronics AB
59
IEEE
NUMERIC_BIT
Types and subprograms for designing with arrays of BIT. Is precompiled into the library
”IEEE” (accessed via USE IEEE.NUMERIC_BIT.ALL).
package NUMERIC_BIT is
type UNSIGNED is array (NATURAL range <>) of BIT;
type SIGNED
is array (NATURAL range <>) of BIT;
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
function
60
“abs” (ARG:SIGNED) return SIGNED;
“-” (ARG:SIGNED) return SIGNED;
“+” (L,R:UNSIGNED) return
“+” (L,R:SIGNED) return
“+” (L:UNSIGNED; R:NATURAL) return
“+” (L:NATURAL; R:UNSIGNED) return
“+” (L:INTEGER; R:SIGNED) return
“+” (L:SIGNED; R:INTEGER) return
“-” (L,R:UNSIGNED) return
“-” (L,R:SIGNED) return
“-” (L:UNSIGNED; R:NATURAL) return
“-” (L:NATURAL; R:UNSIGNED) return
“-” (L:SIGNED; R:INTEGER) return
“-” (L:INTEGER; R:SIGNED) return
“*” (L,R:UNSIGNED) return
“*” (L,R:SIGNED) return
“*” (L:UNSIGNED; R:NATURAL) return
“*” (L:NATURAL; R:UNSIGNED) return
“*” (L:SIGNED; R:INTEGER) return
“*” (L:INTEGER; R:SIGNED) return
“/” (L,R:UNSIGNED) return
“/” (L,R:SIGNED) return
“/” (L:UNSIGNED; R:NATURAL) return
“/” (L:NATURAL; R:UNSIGNED) return
“/” (L:SIGNED; R:INTEGER) return
“/” (L:INTEGER; R:SIGNED) return
“rem” (L,R:UNSIGNED) return
“rem” (L,R:SIGNED) return
“rem” (L:UNSIGNED; R:NATURAL) return
“rem” (L:NATURAL; R:UNSIGNED) return
“rem” (L:SIGNED; R:INTEGER) return
“rem” (L:INTEGER; R:SIGNED) return
“mod” (L,R:UNSIGNED) return
“mod” (L,R:SIGNED) return
“mod” (L:UNSIGNED; R:NATURAL) return
“mod” (L:NATURAL; R:UNSIGNED) return
“mod” (L:SIGNED; R:INTEGER) return
“mod” (L:INTEGER; R:SIGNED) return
“>” (L,R:UNSIGNED) return
“>” (L,R:SIGNED) return
“>” (L:NATURAL; R:UNSIGNED) return
“>” (L:INTEGER; R:SIGNED) return
“>” (L:UNSIGNED; R:NATURAL) return
“>” (L:SIGNED; R:INTEGER) return
“<” (L,R:UNSIGNED) return
“<” (L,R:SIGNED) return
“<” (L:NATURAL; R:UNSIGNED) return
“<” (L:INTEGER; R:SIGNED) return
“<” (L:UNSIGNED; R:NATURAL) return
“<” (L:SIGNED; R:INTEGER) return
“<=” (L,R:UNSIGNED) return
“<=” (L,R:SIGNED) return
“<=” (L:NATURAL; R:UNSIGNED) return
“<=” (L:INTEGER; R:SIGNED) return
“<=” (L:UNSIGNED; R:NATURAL) return
“<=” (L:SIGNED; R:INTEGER) return
“>=” (L,R:UNSIGNED) return
“>=” (L,R:SIGNED) return
“>=” (L:NATURAL; R:UNSIGNED) return
“>=” (L:INTEGER; R:SIGNED) return
“>=” (L:UNSIGNED; R:NATURAL) return
“>=” (L:SIGNED; R:INTEGER) return
“=” (L,R:UNSIGNED) return
“=” (L,R:SIGNED) return
“=” (L:NATURAL; R:UNSIGNED) return
“=” (L:INTEGER; R:SIGNED) return
Copyright © 1997-2000 HARDI Electronics AB
UNSIGNED;
SIGNED;
UNSIGNED;
UNSIGNED;
SIGNED;
SIGNED;
UNSIGNED;
SIGNED;
UNSIGNED;
UNSIGNED;
SIGNED;
SIGNED;
UNSIGNED;
SIGNED;
UNSIGNED;
UNSIGNED;
SIGNED;
SIGNED;
UNSIGNED;
SIGNED;
UNSIGNED;
UNSIGNED;
SIGNED;
SIGNED;
UNSIGNED;
SIGNED;
UNSIGNED;
UNSIGNED;
SIGNED;
SIGNED;
UNSIGNED;
SIGNED;
UNSIGNED;
UNSIGNED;
SIGNED;
SIGNED;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
BOOLEAN;
IEEE
function “=” (L:UNSIGNED; R:NATURAL) return BOOLEAN;
function “=” (L:SIGNED; R:INTEGER) return BOOLEAN;
function “/=” (L,R:UNSIGNED) return BOOLEAN;
function “/=” (L,R:SIGNED) return BOOLEAN;
function “/=” (L:NATURAL; R:UNSIGNED) return BOOLEAN;
function “/=” (L:INTEGER; R:SIGNED) return BOOLEAN;
function “/=” (L:UNSIGNED; R:NATURAL) return BOOLEAN;
function “/=” (L:SIGNED; R:INTEGER) return BOOLEAN;
function SHIFT_LEFT (ARG:UNSIGNED; COUNT:NATURAL)
return UNSIGNED;
function SHIFT_RIGHT (ARG:UNSIGNED; COUNT:NATURAL)
return UNSIGNED;
function SHIFT_LEFT (ARG:SIGNED; COUNT:NATURAL) return SIGNED;
function SHIFT_RIGHT (ARG:SIGNED; COUNT:NATURAL) return SIGNED;
function ROTATE_LEFT (ARG:UNSIGNED; COUNT:NATURAL)
return UNSIGNED;
function ROTATE_RIGHT (ARG:UNSIGNED; COUNT:NATURAL)
return UNSIGNED;
function ROTATE_LEFT (ARG:SIGNED; COUNT:NATURAL) return SIGNED;
function ROTATE_RIGHT (ARG:SIGNED; COUNT:NATURAL) return SIGNED;
function “sll” (ARG:UNSIGNED; COUNT:INTEGER) return UNSIGNED;
function “sll” (ARG:SIGNED; COUNT:INTEGER) return SIGNED;
function “srl” (ARG:UNSIGNED; COUNT:INTEGER) return UNSIGNED;
function “srl” (ARG:SIGNED; COUNT:INTEGER) return SIGNED;
function “rol” (ARG:UNSIGNED; COUNT:INTEGER) return UNSIGNED;
function “rol” (ARG:SIGNED; COUNT:INTEGER) return SIGNED;
function “ror” (ARG:UNSIGNED; COUNT:INTEGER) return UNSIGNED;
function “ror” (ARG:SIGNED; COUNT:INTEGER) return SIGNED;
function RESIZE (ARG:SIGNED; NEW_SIZE:NATURAL) return SIGNED;
function RESIZE (ARG:UNSIGNED;NEW_SIZE:NATURAL) return UNSIGNED;
function TO_INTEGER (ARG:UNSIGNED) return NATURAL;
function TO_INTEGER (ARG:SIGNED) return INTEGER;
function TO_UNSIGNED (ARG,SIZE:NATURAL) return UNSIGNED;
function TO_SIGNED (ARG:INTEGER; SIZE:NATURAL) return SIGNED;
function “not” (L:UNSIGNED) return UNSIGNED;
function “and” (L,R:UNSIGNED) return UNSIGNED;
function “or” (L,R:UNSIGNED) return UNSIGNED;
function “nand” (L,R:UNSIGNED) return UNSIGNED;
function “nor” (L,R:UNSIGNED) return UNSIGNED;
function “xor” (L,R:UNSIGNED) return UNSIGNED;
function “xnor” (L,R:UNSIGNED) return UNSIGNED;
function “not” (L:SIGNED) return SIGNED;
function “and” (L,R:SIGNED) return SIGNED;
function “or” (L,R:SIGNED) return SIGNED;
function “nand” (L,R:SIGNED) return SIGNED;
function “nor” (L,R:SIGNED) return SIGNED;
function “xor” (L,R:SIGNED)
return SIGNED;
function “xnor” (L,R:SIGNED)
return SIGNED;
function RISING_EDGE (signal S:BIT) return BOOLEAN;
function FALLING_EDGE (signal S:BIT) return BOOLEAN;
end package NUMERIC_BIT;
NUMERIC_STD
Types and subprograms for designing with arrays of STD_LOGIC. Is precompiled into
the library ”IEEE” (accessed via USE IEEE.NUMERIC_STD.ALL).
library IEEE;
use IEEE.std_logic_1164.all;
package NUMERIC_STD is
type UNSIGNED is array (NATURAL range <>) of STD_LOGIC;
type SIGNED
is array (NATURAL range <>) of STD_LOGIC;
function
function
function
function
function
function
function
function
function
function
function
”abs” (X:SIGNED)
”-” (ARG:SIGNED)
”+” (L,R:UNSIGNED)
”+” (L,R:SIGNED)
”+” (L:UNSIGNED; R:NATURAL)
”+” (L:NATURAL; R:UNSIGNED)
”+” (L:INTEGER; R:SIGNED)
”+” (L:SIGNED; R:INTEGER)
”-” (L,R:UNSIGNED)
”-” (L,R:SIGNED)
”-” (L:UNSIGNED; R:NATURAL)
return
return
return
return
return
return
return
return
return
return
return
SIGNED;
SIGNED;
UNSIGNED;
SIGNED;
UNSIGNED;
UNSIGNED;
SIGNED;
SIGNED;
UNSIGNED;
SIGNED;
UNSIGNED;
Copyright © 1997-2000 HARDI Electronics AB
61
IEEE
function ”-” (L:NATURAL; R:UNSIGNED) return UNSIGNED;
function ”-” (L:SIGNED; R:INTEGER) return SIGNED;
function ”-” (L:INTEGER; R:SIGNED)
return SIGNED;
function ”*” (L,R:UNSIGNED)
return UNSIGNED;
function ”*” (L,R:SIGNED) return SIGNED;
function ”*” (L:UNSIGNED; R:NATURAL) return UNSIGNED;
function ”*” (L:NATURAL; R:UNSIGNED) return UNSIGNED;
function ”*” (L:SIGNED; R:INTEGER) return SIGNED;
function ”*” (L:INTEGER; R:SIGNED)
return SIGNED;
function ”/” (L,R:UNSIGNED) return UNSIGNED;
function ”/” (L,R:SIGNED)
return SIGNED;
function ”/” (L:UNSIGNED; R:NATURAL) return UNSIGNED;
function ”/” (L:NATURAL; R:UNSIGNED) return UNSIGNED;
function ”/” (L:SIGNED; R:INTEGER) return SIGNED;
function ”/” (L:INTEGER; R:SIGNED)
return SIGNED;
function ”rem” (L,R:UNSIGNED)
return UNSIGNED;
function ”rem” (L,R:SIGNED)
return SIGNED;
function ”rem” (L:UNSIGNED; R:NATURAL) return UNSIGNED;
function ”rem” (L:NATURAL; R:UNSIGNED) return UNSIGNED;
function ”rem” (L:SIGNED; R:INTEGER) return SIGNED;
function ”rem” (L:INTEGER; R:SIGNED)
return SIGNED;
function ”mod” (L,R:UNSIGNED) return UNSIGNED;
function ”mod” (L,R:SIGNED)
return SIGNED;
function ”mod” (L:UNSIGNED; R:NATURAL) return UNSIGNED;
function ”mod” (L:NATURAL; R:UNSIGNED) return UNSIGNED;
function ”mod” (L:SIGNED; R:INTEGER) return SIGNED;
function ”mod” (L:INTEGER; R:SIGNED)
return SIGNED;
function ”>” (L,R:UNSIGNED)
return BOOLEAN;
function ”>” (L,R:SIGNED)
return BOOLEAN;
function ”>” (L:NATURAL; R:UNSIGNED) return BOOLEAN;
function ”>” (L:INTEGER; R:SIGNED)
return BOOLEAN;
function ”>” (L:UNSIGNED; R:NATURAL) return BOOLEAN;
function ”>” (L:SIGNED; R:INTEGER) return BOOLEAN;
function ”<” (L,R:UNSIGNED)
return BOOLEAN;
function ”<” (L,R:SIGNED)
return BOOLEAN;
function ”<” (L:NATURAL; R:UNSIGNED) return BOOLEAN;
function ”<” (L:INTEGER; R:SIGNED)
return BOOLEAN;
function ”<” (L:UNSIGNED; R:NATURAL) return BOOLEAN;
function ”<” (L:SIGNED; R:INTEGER) return BOOLEAN;
function ”<=” (L,R:UNSIGNED) return BOOLEAN;
function ”<=” (L,R:SIGNED)
return BOOLEAN;
function ”<=” (L:NATURAL; R:UNSIGNED) return BOOLEAN;
function ”<=” (L:INTEGER; R:SIGNED)
return BOOLEAN;
function ”<=” (L:UNSIGNED; R:NATURAL) return BOOLEAN;
function ”<=” (L:SIGNED; R:INTEGER) return BOOLEAN;
function ”>=” (L,R:UNSIGNED)
return BOOLEAN;
function ”>=” (L,R:SIGNED)
return BOOLEAN;
function ”>=” (L:NATURAL; R:UNSIGNED) return BOOLEAN;
function ”>=” (L:INTEGER; R:SIGNED)
return BOOLEAN;
function ”>=” (L:UNSIGNED; R:NATURAL) return BOOLEAN;
function ”>=” (L:SIGNED; R:INTEGER) return BOOLEAN;
function ”=” (L,R:UNSIGNED)
return BOOLEAN;
function ”=” (L,R:SIGNED)
return BOOLEAN;
function ”=” (L:NATURAL; R:UNSIGNED) return BOOLEAN;
function ”=” (L:INTEGER; R:SIGNED)
return BOOLEAN;
function ”=” (L:UNSIGNED; R:NATURAL) return BOOLEAN;
function ”=” (L:SIGNED; R:INTEGER) return BOOLEAN;
function ”/=” (L,R:UNSIGNED)
return BOOLEAN;
function ”/=” (L,R:SIGNED)
return BOOLEAN;
function ”/=” (L:NATURAL; R:UNSIGNED) return BOOLEAN;
function ”/=” (L:INTEGER; R:SIGNED)
return BOOLEAN;
function ”/=” (L:UNSIGNED; R:NATURAL) return BOOLEAN;
function ”/=” (L:SIGNED; R:INTEGER) return BOOLEAN;
function SHIFT_LEFT (ARG:UNSIGNED; COUNT:NATURAL)
return UNSIGNED;
function SHIFT_RIGHT (ARG:UNSIGNED; COUNT:NATURAL)
return UNSIGNED;
function SHIFT_LEFT (ARG:SIGNED; COUNT:NATURAL) return SIGNED;
function SHIFT_RIGHT (ARG:SIGNED; COUNT:NATURAL) return SIGNED;
function ROTATE_LEFT (ARG:UNSIGNED; COUNT:NATURAL)
return UNSIGNED;
function ROTATE_RIGHT (ARG:UNSIGNED; COUNT:NATURAL)
return UNSIGNED;
function ROTATE_LEFT (ARG:SIGNED; COUNT:NATURAL) return SIGNED;
function ROTATE_RIGHT (ARG:SIGNED; COUNT:NATURAL) return SIGNED;
62
Copyright © 1997-2000 HARDI Electronics AB
IEEE
function “sll” (ARG:UNSIGNED; COUNT:INTEGER) return UNSIGNED;
function “sll” (ARG:SIGNED; COUNT:INTEGER) return SIGNED;
function “srl” (ARG:UNSIGNED; COUNT:INTEGER) return UNSIGNED;
function “srl” (ARG:SIGNED; COUNT:INTEGER) return SIGNED;
function “rol” (ARG:UNSIGNED; COUNT:INTEGER) return UNSIGNED;
function “rol” (ARG:SIGNED; COUNT:INTEGER) return SIGNED;
function “ror” (ARG:UNSIGNED; COUNT:INTEGER) return UNSIGNED;
function “ror” (ARG:SIGNED; COUNT:INTEGER) return SIGNED;
function RESIZE (ARG:SIGNED; NEW_SIZE:NATURAL) return SIGNED;
function RESIZE (ARG:UNSIGNED;NEW_SIZE:NATURAL) return UNSIGNED;
function TO_INTEGER (ARG:UNSIGNED)
return NATURAL;
function TO_INTEGER (ARG:SIGNED)
return INTEGER;
function TO_UNSIGNED (ARG,SIZE:NATURAL) return UNSIGNED;
function TO_SIGNED (ARG:INTEGER; SIZE:NATURAL) return SIGNED;
function ”not” (L:UNSIGNED)
return UNSIGNED;
function ”and” (L,R:UNSIGNED) return UNSIGNED;
function ”or” (L,R:UNSIGNED) return UNSIGNED;
function ”nand” (L,R:UNSIGNED) return UNSIGNED;
function ”nor” (L,R:UNSIGNED) return UNSIGNED;
function ”xor” (L,R:UNSIGNED) return UNSIGNED;
function ”xnor” (L,R:UNSIGNED) return UNSIGNED;
function ”not” (L:SIGNED)
return SIGNED;
function ”and” (L,R:SIGNED)
return SIGNED;
function ”or” (L,R:SIGNED)
return SIGNED;
function ”nand” (L,R:SIGNED)
return SIGNED;
function ”nor” (L,R:SIGNED)
return SIGNED;
function ”xor” (L,R:SIGNED)
return SIGNED;
function ”xnor” (L,R:SIGNED)
return SIGNED;
function STD_MATCH (L,R:STD_ULOGIC) return BOOLEAN;
function STD_MATCH (L,R:UNSIGNED) return BOOLEAN;
function STD_MATCH (L,R:SIGNED)
return BOOLEAN;
function STD_MATCH (L,R:STD_LOGIC_VECTOR) return BOOLEAN;
function STD_MATCH (L,R:STD_ULOGIC_VECTOR) return BOOLEAN;
function TO_01 (S:UNSIGNED;XMAP:STD_LOGIC:=’0’) return UNSIGNED;
function TO_01 (S:SIGNED; XMAP:STD_LOGIC:=’0’) return SIGNED;
end package NUMERIC_STD;
MATH_REAL
Constants and subprograms for real numbers. Is precompiled into the library ”IEEE”
(accessed via USE IEEE.MATH_REAL.ALL).
package MATH_REAL is
constant MATH_E :
constant MATH_1_OVER_E :
constant MATH_PI :
constant MATH_2_PI :
constant MATH_1_OVER_PI :
constant MATH_PI_OVER_2 :
constant MATH_PI_OVER_3 :
constant MATH_PI_OVER_4 :
constant MATH_3_PI_OVER_2 :
constant MATH_LOG_OF_2 :
constant MATH_LOG_OF_10 :
constant MATH_LOG2_OF_E :
constant MATH_LOG10_OF_E :
constant MATH_SQRT_2 :
constant MATH_1_OVER_SQRT_2:
constant MATH_SQRT_PI :
constant MATH_DEG_TO_RAD :
constant MATH_RAD_TO_DEG :
function
function
function
function
function
function
function
function
SIGN (X :REAL)
CEIL (X :REAL)
FLOOR (X :REAL)
ROUND (X :REAL)
TRUNC (X :REAL)
“MOD” (X,Y:REAL)
REALMAX (X,Y:REAL)
REALMIN (X,Y:REAL)
REAL
REAL
REAL
REAL
REAL
REAL
REAL
REAL
REAL
REAL
REAL
REAL
REAL
REAL
REAL
REAL
REAL
REAL
:=
:=
:=
:=
:=
:=
:=
:=
:=
:=
:=
:=
:=
:=
:=
:=
:=
:=
return
return
return
return
return
return
return
return
2.71828_18284_59045_23536;
0.36787_94411_71442_32160;
3.14159_26535_89793_23846;
6.28318_53071_79586_47693;
0.31830_98861_83790_67154;
1.57079_63267_94896_61923;
1.04719_75511_96597_74615;
0.78539_81633_97448_30962;
4.71238_89803_84689_85769;
0.69314_71805_59945_30942;
2.30258_50929_94045_68402;
1.44269_50408_88963_4074;
0.43429_44819_03251_82765;
1.41421_35623_73095_04880;
0.70710_67811_86547_52440;
1.77245_38509_05516_02730;
0.01745_32925_19943_29577;
57.29577_95130_82320_87680;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
procedure UNIFORM (variable SEED1,SEED2:inout POSITIVE;
variable X:out REAL);
Copyright © 1997-2000 HARDI Electronics AB
63
IEEE
function SQRT (X:REAL) return
function CBRT (X:REAL) return
function “**” (X:INTEGER; Y:REAL) return
function “**” (X:REAL; Y:REAL) return
function EXP (X:REAL) return
function LOG (X:REAL) return
function LOG2 (X:REAL) return
function LOG10 (X:REAL) return
function LOG (X:REAL; BASE:REAL) return
function SIN (X:REAL) return
function COS (X:REAL) return
function TAN (X:REAL) return
function ARCSIN (X:REAL) return
function ARCCOS (X:REAL) return
function ARCTAN (Y:REAL) return
function ARCTAN (Y:REAL; X:REAL) return
function SINH (X:REAL) return
function COSH (X:REAL) return
function TANH (X:REAL) return
function ARCSINH (X:REAL) return
function ARCCOSH (X:REAL) return
function ARCTANH (X:REAL) return
end package MATH_REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
REAL;
MATH_COMPLEX
Constants and subprograms for complex numbers. Is precompiled into the library
”IEEE” (accessed via USE IEEE.MATH_COMPLEX.ALL).
use IEEE.MATH_REAL.all;
package MATH_COMPLEX is
type COMPLEX is record
RE : REAL; -- Real part
IM : REAL; -- Imaginary part
end record;
subtype POSITIVE_REAL is REAL range 0.0 to REAL’HIGH;
subtype PRINCIPAL_VALUE is REAL range -MATH_PI to MATH_PI;
type COMPLEX_POLAR is record
MAG : POSITIVE_REAL; -- Magnitude
ARG : PRINCIPAL_VALUE; -- Angle in radians
end record;
constant MATH_CBASE_1 : COMPLEX := COMPLEX’(1.0, 0.0);
constant MATH_CBASE_J : COMPLEX := COMPLEX’(0.0, 1.0);
constant MATH_CZERO : COMPLEX := COMPLEX’(0.0, 0.0);
function “=” (L:COMPLEX_POLAR; R:COMPLEX_POLAR)
return BOOLEAN;
function “/=” (L:COMPLEX_POLAR; R:COMPLEX_POLAR)
return BOOLEAN;
function CMPLX (X:REAL; Y:REAL:=0.0) return COMPLEX;
function GET_PRINCIPAL_VALUE(X:REAL) return PRINCIPAL_VALUE;
function COMPLEX_TO_POLAR (Z:COMPLEX) return COMPLEX_POLAR;
function POLAR_TO_COMPLEX (Z:COMPLEX_POLAR) return COMPLEX;
function “ABS” (Z:COMPLEX) return POSITIVE_REAL;
function “ABS” (Z:COMPLEX_POLAR) return POSITIVE_REAL;
function ARG (Z:COMPLEX) return PRINCIPAL_VALUE;
function ARG (Z:COMPLEX_POLAR)
return PRINCIPAL_VALUE;
function “-” (Z:COMPLEX) return COMPLEX;
function “-” (Z:COMPLEX_POLAR)
return COMPLEX_POLAR;
function CONJ (Z:COMPLEX) return COMPLEX;
function CONJ (Z:COMPLEX_POLAR)
return COMPLEX_POLAR;
function SQRT (Z:COMPLEX) return COMPLEX;
function SQRT (Z:COMPLEX_POLAR)
return COMPLEX_POLAR;
function EXP (Z:COMPLEX) return COMPLEX;
function EXP (Z:COMPLEX_POLAR)
return COMPLEX_POLAR;
function LOG (Z:COMPLEX) return COMPLEX;
function LOG2 (Z:COMPLEX) return COMPLEX;
function LOG10 (Z:COMPLEX) return COMPLEX;
function LOG (Z:COMPLEX_POLAR)
return COMPLEX_POLAR;
function LOG2 (Z:COMPLEX_POLAR)
return COMPLEX_POLAR;
function LOG10 (Z:COMPLEX_POLAR)
return COMPLEX_POLAR;
function LOG (Z:COMPLEX; BASE:REAL) return COMPLEX;
64
Copyright © 1997-2000 HARDI Electronics AB
IEEE
function LOG (Z:COMPLEX_POLAR; BASE:REAL)
return COMPLEX_POLAR;
function SIN (Z:COMPLEX) return COMPLEX;
function SIN (Z:COMPLEX_POLAR)
return COMPLEX_POLAR;
function COS (Z:COMPLEX) return COMPLEX;
function COS (Z:COMPLEX_POLAR)
return COMPLEX_POLAR;
function SINH (Z:COMPLEX) return COMPLEX;
function SINH (Z:COMPLEX_POLAR)
return COMPLEX_POLAR;
function COSH (Z:COMPLEX) return COMPLEX;
function COSH (Z:COMPLEX_POLAR)
return COMPLEX_POLAR;
function “+” (L:COMPLEX; R:COMPLEX) return COMPLEX;
function “+” (L:REAL; R:COMPLEX) return COMPLEX;
function “+” (L:COMPLEX; R:REAL) return COMPLEX;
function “+” (L:COMPLEX_POLAR; R:COMPLEX_POLAR)
return COMPLEX_POLAR;
function “+” (L:REAL; R:COMPLEX_POLAR) return COMPLEX_POLAR;
function “+” (L:COMPLEX_POLAR; R:REAL) return COMPLEX_POLAR;
function “-” (L:COMPLEX; R:COMPLEX) return COMPLEX;
function “-” (L:REAL; R:COMPLEX) return COMPLEX;
function “-” (L:COMPLEX; R:REAL) return COMPLEX;
function “-” (L:COMPLEX_POLAR; R:COMPLEX_POLAR)
return COMPLEX_POLAR;
function “-” (L:REAL; R:COMPLEX_POLAR) return COMPLEX_POLAR;
function “-” (L:COMPLEX_POLAR; R:REAL) return COMPLEX_POLAR;
function “*” (L:COMPLEX; R:COMPLEX) return COMPLEX;
function “*” (L:REAL; R:COMPLEX) return COMPLEX;
function “*” (L:COMPLEX; R:REAL) return COMPLEX;
function “*” (L:COMPLEX_POLAR; R:COMPLEX_POLAR)
return COMPLEX_POLAR;
function “*” (L:REAL; R:COMPLEX_POLAR) return COMPLEX_POLAR;
function “*” (L:COMPLEX_POLAR; R:REAL) return COMPLEX_POLAR;
function “/” (L:COMPLEX; R:COMPLEX) return COMPLEX;
function “/” (L:REAL; R:COMPLEX) return COMPLEX;
function “/” (L:COMPLEX; R:REAL) return COMPLEX;
function “/” (L:COMPLEX_POLAR; R:COMPLEX_POLAR)
return COMPLEX_POLAR;
function “/” (L:REAL; R:COMPLEX_POLAR) return COMPLEX_POLAR;
function “/” (L:COMPLEX_POLAR; R:REAL) return COMPLEX_POLAR;
end package MATH_COMPLEX;
Copyright © 1997-2000 HARDI Electronics AB
65
VHDL guide
VHDL guide
Introduction
This chapter describes how VHDL code is written at HARDI Electronics
AB. This coding method is used and taught at the training course ”VHDL
for design and modelling”.
File notation
Files for the five design units in VHDL are named according to the following:
Entity
Architecture
Package
Package Body
Configuration
Name_e.vhd
Name_a.vhd
Name_p.vhd
Name_b.vhd
Name_c.vhd
Libraries are named arbitrarily.
Predefined packages
It is recommended to use the packages standardized by IEEE (see pages
56-65). Non standardized packages, for example STD_LOGIC_ARITH,
STD_LOGIC_SIGNED, NUMERIC_SIGNED, STD_LOGIC_UNSIGNED
and NUMERIC_UNSIGNED, are to be avoided.
VHDL syntax
Reserved words and objects
All reserved words are written with upper-case letters. Objects (constants,
variables, signals and files) are written with lower-case letters as compound
words, and with upper-case letters separating the words. The first letter is
always lower-case.
Counter: PROCESS
BEGIN
WAIT UNTIL clock = ‘1’;
numberOfCycles <= numberOfCycles + 1;
END PROCESS Counter;
Types
Predefined types are written with upper-case letters. Userdefined types are
written just as objects, but with the first letter as upper-case.
TYPE Matrix IS ARRAY (NATURAL RANGE <>, NATURAL RANGE <>) OF BIT;
SUBTYPE MyNumbers IS NATURAL RANGE 0 TO 7;
Attributes, packages and libraries
Attributes, packages and libraries are written with upper-case letters except for user-defined attributes and packages that are written with lowercase letters (packages start with an upper-case letter).
WAIT UNTIL clk’EVENT AND clk = ‘1’;
LIBRARY IEEE;
USE IEEE.STD_LOGIC_1164.ALL;
ATTRIBUTE syn_encoding OF State : TYPE IS ”onehot”;
66
Copyright © 1997-2000 HARDI Electronics AB
VHDL guide
Hexadecimal values
Hexadecimal values are written using upper-case letters.
myVariable := X”AB14”;
Replacement characters
Replacement characters are not used (LRM 13.10).
Indentation
Indentation is used to make the VHDL code well structured and easy to read.
Declarative regions and expressions are indented two spaces. TAB is not used
since the TAB setting may differ between different computers.
ARCHITECTURE Behave OF Counter IS
BEGIN
Count: PROCESS(choose)
VARIABLE myNumber : INTEGER := 0;
BEGIN
IF choose = ‘1’ THEN
myNumber := myNumber + 1;
REPORT ”Adding”;
ELSE
myNumber := myNumber - 1;
REPORT ”Subtracting”;
END IF;
outputData <= myNumber;
END PROCESS Count;
END ARCHITECTURE Behave;
Indentation of the CASE statement
CASE statements are indented to clearly show the different conditions.
CASE state IS
WHEN Start => IF i = ‘0’ THEN
nextState <= Stop;
ELSE
nextState <= Start;
END IF;
WHEN Stop => nextState <= Start;
END CASE;
Line construction
A line shall not include more than 80 characters. Longer lines shall be divided
into several lines and all new lines shall continue at a similar expression
on the previous line.
IF myVeryVeryLongVariableName AND
mySecondVeryVeryLongVariableName THEN ...
PORT (clk : IN BIT;
myNumber : IN INTEGER;
ok : OUT BOOLEAN);
Comments
Comments are placed either before the code to be commented, or on the
same line.
-- This process adds two numbers
Adder: PROCESS(number1, number2) IS
BEGIN
sum <= number1 + number2; -- Here is the addition
END PROCESS Adder;
Concurrent statements
Concurrent statements are separated by an empty line.
Copyright © 1997-2000 HARDI Electronics AB
67
VHDL guide
ARCHITECTURE Behave OF Design IS
BEGIN
ASSERT a = b
REPORT ”a is not equal to b”;
clock <= NOT clock AFTER 20 ns;
PROCESS(clock)
BEGIN
IF clock = ‘1’ THEN
q <= d;
END IF;
END PROCESS;
END ARCHITECTURE Behave;
Operators
Space is used to separate operators binding harder or as hard as binary ’+’
and ’-’. Operators written as text are always preceded by a space.
With space
Without space
+
-
MOD, REM, ABS
shift, rotation
logical
comparison
*
/
**
mySignal <=
myArray :=
myLogicalSignal <=
myBoolean <=
((in1 + in2 - in3)*in4**2)/in5;
myArray SLA 2;
in4 AND in5;
a > b;
Assignments
Every assignment is written on a separate line justified vertically according
to equal lines.
outData <= inData AFTER 5 ns;
dataBus <= GUARDED memory(address);
Declarations
Each declaration is written on a separate line justified vertically according
to equal lines.
SIGNAL outData : BIT;
SIGNAL dataBus : Resolve INTEGER BUS;
Associations
Named associations using more than one line are justified vertically. Named
association is preferably used instead of positional association since the association then is independent of the order of the associations.
PORT MAP(data => outData, address => address,
wr => wr, rd => rd);
Naming of concurrent statements
Concurrent statements shall be named to simplify simulation. The name shall
directly be followed by a ‘:’, then a space and then the named concurrent
statement. The name is always started by an upper-case letter.
Clockpulse: clock <= NOT clock AFTER 5 ns;
Adder: PROCESS(number1, number2) IS
BEGIN
sum <= number1 + number2;
END PROCESS Adder;
68
Copyright © 1997-2000 HARDI Electronics AB
VHDL guide
Loops
Nested loops shall be named. NEXT and EXIT shall denote which loop
they belong to.
L1: WHILE a > b LOOP
L2: FOR i IN a TO b LOOP
a := i - b;
b := b - 1;
EXIT L1 WHEN a = b;
END LOOP L2;
END LOOP L1;
END
END shall be qualified when the syntax permits it.
ENTITY Adder IS
PORT(number1, number2 : IN INTEGER;
sum : OUT INTEGER);
END ENTITY Adder;
Simulation and synthesis
Variables and signals
Variables are prefered over signals since they need less simulation memory
and are handled faster.
Enumerated types
Enumerated types are prefered for state machines.
TYPE state IS (Start, Glitch, Pulse, Stop);
Constraints
Integers must be constrained to avoid 32 bit data paths in code written for
synthesis.
SIGNAL data : INTEGER RANGE 0 TO 255;
Named constants are used when constraining parameters.
CONSTANT length : NATURAL := 5;
SUBTYPE MyArrayType IS BIT_VECTOR(length - 1 DOWNTO 0);
SIGNAL myArray : MyArrayType;
Copyright © 1997-2000 HARDI Electronics AB
69
VHDL’87 and VHDL’93
VHDL’87 and VHDL’93, differences
This chapter describes the most essential differences between VHDL’87
and VHDL’93.
Syntax
VHDL’93 has a more symmetric syntax, especially for the conclusion of
composite statements and the five design units. Below follow examples
of conclusions different in the two versions of the standard (note that the
VHDL’87 syntax is permitted also in VHDL’93):
VHDL’87
end
end
end
end
end
end
end
end
end
entity_name;
arch_name;
pck_name;
pck_name;
conf_name;
component;
fn_name;
proc_name;
record;
VHDL’93
See page
end
end
end
end
end
end
end
end
end
24
25
22
23
26, 48
44
31
32
9
entity entity_name;
architecture arch_name;
package pck_name;
package body pck_name;
configuration conf_name;
component comp_name;
function fn_name;
procedure proc_name;
record rec_name;
Below follow examples where the start of statements differ:
VHDL’87
VHDL’93
blk_name: block
blk_name: block is
proc_name: process proc_name: process is
component comp_name component comp_name is
See page
41
38
44
Above the previous examples VHDL’93 permits labeling of all statements.
Composite statements may then use the label also at the end of the statement,
for example:
Control: IF a > b THEN
...
END IF Control;
That is not permitted in VHDL’87.
GENERATE
The GENERATE statement (see page 45) has in VHDL’93 been enhanced
with a declarational part and has also been raised to a block with a local
scope. The GENERATE statement in VHDL’87 does not have a declarational
part. It is however possible to write code compatible with both standards by
avoiding the declarational part and by putting a BLOCK statement within
the GENERATE statement.
Concurrent signal assignment
Conditional concurrent signal assignments (see page 41) must in VHDL’87
have an concluding ELSE condition. The reserved word UNAFFECTED,
that is new to VHDL’93, was included to be able to leave a signal unaffected
during an assignment, i.e. to keep its previous value:
a <= b WHEN s=’1’ ELSE a; -- VHDL’87 requires a concluding ELSE
a <= b WHEN s=’1’; -- Works in VHDL’93
a <= b
WHEN t=”00” ELSE -- Works in VHDL’93
UNAFFECTED WHEN t=”01” ELSE
c;
70
Copyright © 1997-2000 HARDI Electronics AB
VHDL’87 and VHDL’93
Files
The handling of files differ quite a lot between VHDL’87 and VHDL’93 (see
page 19-21). Most changes are not backwards compatible. Below follow
examples of the different versions of file declarations:
-- VHDL’87:
FILE f1 : myFile IS IN ”name_in_file_system”;
FILE f2 : mySecondFile IS OUT ”name_in_file_system”;
-- VHDL’93:
FILE f1 : myFile OPEN READ_MODE IS ”name_in_file_system”;
FILE f2 : mySecondFile OPEN WRITE_MODE IS ”name_in_file_system”;
Input files may be written in VHDL code compatible with both VHDL’87
and VHDL’93, but for output files that is not possible:
-- Declaration of an input file both for VHDL’87 and VHDL’93
FILE f : myFile IS ”name_in_file_system”;
The predefined subprograms FILE_OPEN and FILE_CLOSE does not
exist in VHDL’87.
File parameters for subprograms do not have a mode in VHDL’93 as they
do in VHDL’87. Input files for subprograms may be written in VHDL code
compatible with both VHDL’87 and VHDL’93:
-- Subprogram with a file parameter for both VHDL’87 and VHDL’93
PROCEDURE ReadFile(FILE f : myFile; value : OUT INTEGER);
Functions using files outside their local scope must in VHDL’93 be declared
as IMPURE. IMPURE does not exist in VHDL’87.
Character set
The character set in VHDL’93 (see page 7, 56-57) is completely ISO
8859-1 : 1987(E) compatible and includes 256 characters. The character
set in VHDL’87 is limited to the first 128 characters and does not include
international characters, not even in comments. Many VHDL’87 tools do
however support international charactersr in comments.
Extended identifiers
VHDL’93 permits the usage of extended identifiers. An extended identifier
always starts and ends with a ‘\’ (backslash) and may include for example spaces and reserved words. Note that extended identifiers are case sensitive.
Shared variables
VHDL’93 permits shared variables (see page 17) in concurrent declaration
statements.
Impure functions
An impure function does not only work via its parameters and may therefore
return different values with identical input parameters. A function calling
an impure function, or a procedure with side-effects (a procedure not only
working via its parameters), must be declared as impure. The function NOW,
that returns current simulation time, is an impure function in VHDL’93. All
functions utilizing NOW must therefore be declared as impure.
Copyright © 1997-2000 HARDI Electronics AB
71
VHDL’87 and VHDL’93
Direct instantiation
In VHDL’93 it is permitted to exclude the component declaration and directly
instantiate an ENTITY or a CONFIGURATION DECLARATION. This is
called direct instantiation (see pages 46, 47). In VHDL’87 a component
declaration is needed.
Port associations
In VHDL’93 it is permitted to have a constant value as actual parameter for
an input port in a parameter association list (see pages 47-50). In VHDL’87
an actual parameter must be a signal.
VHDL’93 does also permit, above type conversion functions, that direct type
conversion (type conversion functions between closely related types) is used
between formal and actual parameters (see pages 43, 44, 47). In VHDL’93
it is also possible to have a slice as formal parameter.
Attributes
A number of new attributes (see pages 51-55) are added to VHDL’93. They
are ‘ASCENDING, ‘IMAGE, ‘VALUE, ‘DRIVING, ‘DRIVING_VALUE,
‘SIMPLE_NAME, ‘INSTANCE_NAME and ‘PATH_NAME.
The lack of the attribute ‘IMAGE in VHDL’87 may be quite annoying and
one must write functions that convert values to text strings. In some cases
it is possible to utilize STD.TEXTIO.READ and STD.TEXTIO.WRITE to
create such functions, at least for the predefined types:
FUNCTION INTEGER_IMAGE(i : INTEGER) RETURN STRING IS
USE STD.TEXTIO.ALL;
-- Determines the number of characters in the string
FUNCTION length(i : INTEGER) RETURN NATURAL IS
VARIABLE l : LINE;
VARIABLE tmp : NATURAL;
BEGIN
WRITE(l,i);
tmp := l’LENGTH;
DEALLOCATE(l); -- Remove the line pointer
RETURN tmp;
END FUNCTION length;
VARIABLE st : STRING(1 TO length(i));
VARIABLE l : LINE;
BEGIN
WRITE(l,i);
st := l.ALL;
DEALLOCATE(l); -- Remove the line pointer
RETURN st;
END FUNCTION INTEGER_IMAGE;
The attributes ‘STRUCTURE and ‘BEHAVIOR were removed to
VHDL’93.
REPORT
The REPORT statement is new to VHDL’93. In VHDL’87 it is possible to
utilize REPORT in combination with ASSERT:
ASSERT FALSE REPORT ”...”;
72
Copyright © 1997-2000 HARDI Electronics AB
VHDL’87 and VHDL’93
Signal delay mechanisms
INERTIAL is new to VHDL’93 and is used to express an inertial delay (see
page 37). In VHDL’93 it is possible to combine INERTIAL and TRANSPORT in a signal assignment using REJECT. That is not possible in VHDL’87
and an extra signal is needed to obtain the same functionality:
-- VHDL’93:
a <= REJECT 2 ns INERTIAL b AFTER 5 ns;
-- VHDL’87:
tmp <= b AFTER 2 ns;
a <= TRANSPORT tmp AFTER 3 ns;
Delayed concurrent statements
In VHDL’93 it is possible to declare all concurrent statements active during
simulation (see pages 38-42) as POSTPONED which means that they are
executed as the final delta at a specific occasion. VHDL’87 does not have
that functionality and there are no tricks to manually create it.
Alias
In VHDL’87 aliases (see page 22) may be declared only for objects, while it
in VHDL’93 is possible to declare aliases also for subprograms, operators,
types and for all named entities except ”labels”, ”loop parameters” and
”generate parameters”.
Bit string literals
In VHDL’87 a bit string literal is always of the type BIT_VECTOR. In
VHDL’93 the bit string literals have been generalized to be an alternative
way to write an aggregate of any array type whose elements can have the
values ‘0’ or ‘1’.
-- Permitted in VHDL’93
LIBRARY IEEE;
USE IEEE.STD_LOGIC_1164.ALL;
...
SIGNAL s : STD_LOGIC_VECTOR(0 TO 15);
...
s <= x”A1B0”;
Unfortunately this generalization may arise ambiguousnesses when overloaded subprograms are used. The assignment above should be written like
this in VHDL’87:
s <= TO_STDLOGICVECTOR(x”A1B0”);
This will however result in a compilation error in VHDL’93 since the bit
string literal fits many different array types, and it is therefore not possible
for the compiler to determine which of all conversion functions named
TO_STDLOGICVECTOR to use.
The following line works fine both for VHDL’87 and for VHDL’93:
s <= TO_STDLOGICVECTOR(BIT_VECTOR’(x”A1B0”));
Copyright © 1997-2000 HARDI Electronics AB
73
Index
Index
A
’ACTIVE 54
’ASCENDING Arrays 53
’ASCENDING Types 51
ACCESS 12
Actual parameters 39
AFTER 37, 41, 73
Aggregates 13
ALIAS 22, 73
ARCHITECTURE 27
ARRAY 10
ASSERT 38
ATTRIBUTE 15
Attributes
Predefined 51, 72
User-defined 15
B
‘BEHAVIOR 72
’BASE 51
Backus-Naur-format 7
BIT 8, 56
BIT_VECTOR 8, 57
Bit string literals 73
BLOCK 43
BOOLEAN 8, 56
C
CASE 31
CHARACTER 8, 56, 71
Component configuration 48, 49, 50
Component declaration 46
Component instantiation 47
Concatenation operator (&) 10
Concurrent signal assignment 41, 42, 70
Configuration (default) 48
CONFIGURATION (design unit) 28
Configuration declaration 28, 50
Configuration specification 49
CONSTANT 16
D
’DELAYED 54
’DRIVING 54
’DRIVING_VALUE 18, 54
DEALLOCATE 12
Default configuration 48
Deferred constant declaration 16
DELAY_LENGTH 8, 57
Delay mechanisms 37, 73
Direct instantiation 46, 47, 72
E
’EVENT 54
ENTITY 26
EXIT 32
Extended identifiers 4, 71
F
FILE_OPEN_KIND 8, 57, 71
FILE_OPEN_STATUS 8, 57, 71
74
Copyright © 1997-2000 HARDI Electronics AB
File declaration 19, 71
File handling 19, 71
File reading, TEXTIO 20
File writing, TEXTIO 21
Formal parameters 33, 34, 39
FUNCTION 33
G
GENERATE 45, 70
GENERIC 44
GENERIC MAP 44
Generic parameters 44
GROUP 14
GUARD 43
H
’HIGH, Arrays 52
’HIGH, Types 51
I
’IMAGE 51, 72
’INSTANCE_NAME 55
Identifier 4
IEEE standards 56
IF 30
IMPURE FUNCTION 33, 71
Incremental binding 50
INERTIAL 37, 73
INPUT 20
INTEGER 8, 57
L
’LAST_ACTIVE 54
’LAST_EVENT 54
’LAST_VALUE 54
’LEFT, Arrays 52
’LEFT, Types 51
’LEFTOF 52
’LENGTH 53
’LOW, Arrays 52
’LOW, Types 51
Lexical elements 4
LIBRARY 23
LINE 12, 20, 21, 57
Literals 5
LOOP 32
M
MATH_COMPLEX package 64
MATH_REAL package 63
N
Named association
Aggregates 13
Generic parameters 44
Ports 43, 47, 48, 49, 50
Subprograms 33, 34, 39
NATURAL 8, 57
NEW 12
NEXT 32
NOW 29, 71
NULL 5, 12, 31
NUMERIC_BIT package 60
NUMERIC_STD package 61
Index
O
OPEN 47, 49
Operators
Comparing 8, 10, 11, 12
Concatenation (&) 10
Logical 8, 10
Predefined 8
Rotation 8, 10
Shift 8, 10
OTHERS 13, 31
OUTPUT 21
P
’PATH_NAME 55
’POS 51
’PRED 52
PACKAGE BODY 25
PACKAGE DECLARATION 24
Pointers 12
PORT MAP 43, 44, 47, 72
Positional association
Aggregates 13
Generic parameters 44
Ports 43, 47, 48, 49, 50
Subprograms 33, 34, 39
POSITIVE 8, 57
POSTPONED 38, 40, 41, 42, 73
POSTPONED ASSERT 38, 73
POSTPONED PROCESS 40, 73
Predefined attributes on:
Arrays 52
Named entities 54
Signals 53
Types 51
Predefined operators 9
Predefined packages 56
MATH_COMPLEX 64
MATH_REAL 63
NUMERIC_BIT 60
NUMERIC_STD 61
STANDARD 56
STD_LOGIC_1164 58
TEXTIO 57
Predefined subtypes 8, 56
Predefined types 8, 56
PROCEDURE 34
PROCESS 40
PURE FUNCTION 33
Q
’QUIET 54
R
’RANGE 53
’REVERSE_RANGE 53
’RIGHT, Arrays 53
’RIGHT, Types 51
’RIGHTOF 52
READ 20
READLINE 20
REAL 8, 57
RECORD 11
REJECT 37, 73
REPORT 38, 72
Reserved words 6
RETURN 35
Rotation operators 8, 10
S
’SIMPLE_NAME 54
’STABLE 53
’STRUCTURE 72
’SUCC 52
SELECT 42
Sensitivity list 40
SEVERITY 8, 38, 57
SHARED VARIABLE 17, 71
Shift operators 8, 10
SIGNAL 18
Signal assignment 37, 41, 42
Signal declaration 18
Slice 10, 72
STANDARD package 56
STD_LOGIC_1164 package 58
STRING 8, 57
Subprograms
Call 39, 71
Function 33
Procedure 34
Subtypes
Declaration 9
Predefined 8, 56
Syntax description 7
T
’TRANSACTION 54
TEXTIO 19, 20, 21
TEXTIO package 57
TIME 8, 57
TRANSPORT 37, 73
Types
Declaration 9
Predefined 8, 56
U
UNAFFECTED 41, 42
USE 23
V
’VAL 52
’VALUE 51
VARIABLE 17
Variable assignment 36
Variable declaration 17
VHDL’87/93, differences 70
VHDL guide 66
W
WAIT 29
WHEN 41
WORK 23
WRITE 21
WRITELINE 21
Copyright © 1997-2000 HARDI Electronics AB
75
A wealth of
experience
Founded in 1987, in the same year that saw the
standardization of the origi­nal version of VHDL
by the IEEE, HARDI Electronics is a pioneer
in the field of structured design. Our knowledge
and experience ranges from ASIC design with
silicon compilers, to the synthesis of programmable devices and the creation of VHDL
designs – the first of which was produced a few
months after the company’s founding.
We work in the fields of design, training and
consultancy and carry out this work both according to the methods that we teach and with
the tools that we sell. It is this philosophy that
has provided us with the kind of in-depth, expert
knowledge of EDA tools and rational working
methods that has contributed to our holding
a position as one of the market leaders in the
structured hardware design industry.
Those Nordic companies benefiting from our
services include Ericsson, Nokia, ABB, Volvo
and SAAB.
Since the year 2000 we develop
hardware platforms for ASIC Prototyping.
Visit www.hardi.com for info about HAPS,
our ASIC Prototyping System.
The four lane highway towards
hardware
designs
Weerror-free
have
moved!
Address: Derbyvägen
6 B,Electronics
SE-212 35 MALMÖ,
Sweden
HARDI
AB
Tel: +46-40-59 29
• Fax:78
+46-40-59
01
Kalkstensvägen
3,00
SE-224
LUND,29
Sweden
info@hardi.se
http://www.hardi.se
Tel:Internet:
+46-(0)46-16
29 00 • •Fax:
+46-(0)46-16 29 01
www.hardi.com • info@hardi.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising