Quick start guide: Sony SNC

Quick start guide: Sony SNC
4-474-879-11(1)
Quick Start Guide
Help
Connecting to a Wi-Fi network
1
1
Connection was successful.
Preparing the camera
Attach the supplied Wi-Fi module to the module connector.
Connect the supplied AC adapter to the power input terminal of this
unit, then connect to a wall outlet.
SNC toolbox
The POWER indicator and NETWORK indicator light green.

Wi-Fi network connection was successful. See 3.
Connection was not successful.
Wi-Fi module
(IFU-WLM3)
The POWER indicator lights green, and the NETWORK indicator flashes orange.

1
*3 If you are using Windows XP Service Pack 2 or later, Windows Vista, Windows 7 or
Windows 8, disable Windows Firewall. For details, refer to the Application Guide.
*5
2
SNC-CX600W
LED indicators
© 2013 Sony Corporation Printed in China
About the manuals
ˎˎ Quick Start Guide (this document)
The Quick Start Guide describes the camera setting method. Be sure to read this
before operating.
ˎˎ Safety Regulations (supplied)
The Safety Regulations describes the secure usage of camera. Be sure to read it.
ˎˎ Installation Manual (supplied)
The Installation Manual describes the camera installation and connection. Be
sure to read it.
ˎˎ On-line manuals
You can download the above manuals from the following URL.
http://www.sony.net/ipela/snc
POWER indicator
Web browser
Download “SNC toolbox” installer from the following URL.
http://www.sony.net/ipela/snc
*6 When you display the camera viewer for the first time, “Security Warning” is
displayed on the monitor. Click [Yes], and install ActiveX Control.
Install SNC toolbox.
Decompress the downloaded installer zip file.
Double-click “SncToolbox_Setup.exe.”
For details on installation and usage, refer to the Application Guide.
NETWORK indicator
1
Connecting to a Wi-Fi network
Set the router’s WPS to valid, and perform the following steps within
one minute.
For details, refer to the operating instructions of your router.
2
Press the WPS button, then confirm that the POWER indicator and
NETWORK indicator flash green.
The camera(s) connected to the local network is detected and its list is
displayed on the Monitor.
4
5
To access the camera, double-click the model name “SNC-CX600W” and
start the web browser.
Confirm the video images via the web browser.
Example
Main menu
Rear panel
Notes
ˎˎ Prepare a Wi-Fi CERTIFIED and WPS compatible router and computer.
ˎˎ The factory setting of Wi-Fi and wired network of the camera is DHCP.
ˎˎ Validate the DHCP setting of your router.
WPS button
Control panel
It may take about 2 minutes to establish a WPS connection.
*8 If installation of ActiveX is prohibited by the pop-up block function of Internet
Explorer or pop-up blocking software, installation of ActiveX is not possible.
*9 If video images are not displayed correctly, set the security level of Internet
Explorer to [Medium] or lower. For details, see the User's Guide.
*11 While accessing this unit, web pages are displayed in JavaScript. If your
computer uses the above anti-virus software, etc., web pages may not be displayed
correctly.
after connecting to the wall outlet, then see 2.
2
Before installing ActiveX Control, log in to your computer as Administrator.
*10 If your computer uses anti-virus software, security software, personal firewall,
or pop up blocker, camera performance (displayed frame rate) may deteriorate.
Start SNC toolbox.
Confirm that the POWER indicator turns green about one minute
About system configuration
Computer
3
Before installing SNC toolbox, log in to your computer as Administrator.
Confirm the camera video images
*7
Network Camera
Router
*2 If your computer uses a personal firewall software or anti-virus software, SNC
toolbox may not operate correctly. In this case, invalidate the corresponding
software.
*4 For details on fixed IP settings, DNS server address, HTTP port settings, or Proxy
Server settings, see the Application Guide.
Return to 2-1.
3
*1 When you begin, “User Account Control – An unidentified program wants access
to your computer” may appear. In this case, click “Allow.”
Monitor
Confirmation of camera video images is finished.
For details, see the User's Guide.
Connecting to a wired network
Confirm radio signal status
Preparing the camera
1
Additional Informations
Connect the network cable to the network port on the rear panel.
1
Click [Setting] in the main menu.
The certificate dialogue is displayed. When you input the administrator’s
user name and password, the administrator setting menu is displayed.
*The factory setting of the administrator’s user name and password is set
to [admin].
Change the password from the factory setting for the security of your
devices.
2
3
Initializing this unit
Troubleshooting
If you experience any difficulties while using this guide, check the following.
POWER indicator and NETWORK indicator are unlit.
ˎˎ The AC adapter is connected correctly.
ˎˎ The supplied AC adapter is used.
ˎˎ Do not use an extension cord or a power strip.
ˎˎ Try another wall outlet.
Video images are not displayed.
Click [Network] of the administrator’s setting menu.
The [Network] menu is displayed.
Click the [Wi-Fi] tab to display the wireless setting menu.The radio
signal level and connection status are displayed.
ˎˎ Check the notes *1 to *11 of “Help.”
ˎˎ Unplug the AC adapter from the wall outlet for 10 seconds, then plug it in again.
If video images are still not displayed, initialize this unit. For details, see “Initializing
this unit.”
Wi-Fi network connection cannot be established.
Note
2
ˎˎ Confirm that your Wi-Fi router is
Check whether the strength of radio wave is fine. If sensitivity is less than
60 %, the following steps may help to improve the reception environment.
Connect the supplied AC adapter to the power input terminal of this
unit, then connect to a wall outlet.
1. Change the camera setting position.
2. Adjust the antenna angle of the Wi-Fi router.
3. Change the setting position of the Wi-Fi router.
4. Install a repeater.
About indicators
The following shows the camera status by the color/lit/flashing/unlit condition of the
POWER indicator and NETWORK indicator.
POWER indicator lit
Camera status
Lights green
Operating normally
Unlit
Not connected to the network
Flashes orange
WPS connection is not successful
POWER indicator flashing
POWER indicator
NETWORK indicator
Camera status
Repeats greenyelloworange
Software version is being upgraded
Flashes green
WPS is connecting
Repeats greenyellowunlitgreenˎ
after connecting to the wall outlet. See 3 of “Connecting to a Wi-Fi
network.”
ˎˎ Validate the DHCP setting of your router.
ˎˎ If Wi-Fi connection is not established via WPS, connect to the Wi-Fi router manually.
For details, refer to User's Guide.
ˎˎ Perform “Connect to a wired network” and check “Confirm radio signal status” of
“Additional Informations.”
If you cannot connect to the network by the above operations, initialize this unit. For
details, see “Initializing this unit.”
ˎˎ Confirm that the network cable is connected correctly to the camera, router, and
computer.
ˎˎ Validate the DHCP setting of your router.
ˎˎ Change the network cable since it may be broken.
If the display flickers, set “Flickerless” to valid.
For details, refer to User's Guide.
This unit is inactive.
Initializing
Unplug the AC adapter from the wall outlet for 10 seconds, then plug it in again.
POWER indicator unlit
NETWORK indicator
Confirm that the POWER indicator turns green about one minute
WPS compatible.
The display flickered.
NETWORK indicator
orangeunlit
Wi-Fi CERTIFIED compatible and
The wired network connection cannot be established.
NETWORK indicator
LED indicators
With the unit turned on, press the reset switch with a ball-point pen, etc. The settings
will return to their factory defaults.
Camera status
Unlit
No power supplied
Lights green
Starting
Lights orange
Preparing to initialize
Reset switch
For the security of your devices
Change the password from the factory setting. The following are the factory settings
of this unit.
Administrator’s user name
IP address
admin
Administrator’s password
IP address assigned automatically (DHCP)
admin
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising