4821-A2-GN20
BitStorm™ 4800
Installation Guide
Document No. 4821-A2-GN20-00
April 2002
Copyright © 2002 Paradyne Corporation.
All rights reserved.
Printed in U.S.A.
Notice
This publication is protected by federal copyright law. No part of this publication may be copied or distributed,
transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or
by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express
written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.
Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation
reserves the right to revise this publication and to make changes from time to time in the contents hereof without
obligation of Paradyne Corporation to notify any person of such revision or changes.
Changes and enhancements to the product and to the information herein will be documented and issued as a new
release to this manual.
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor directly for any help needed. For additional
information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or
Paradyne worldwide office locations, use one of the following methods:
„
„
Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at
www.paradyne.com/warranty.)
Telephone: Call our automated system to receive current information by fax or to speak with a company
representative.
—
Within the U.S.A., call 1-800-870-2221
—
Outside the U.S.A., call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail them to Technical Publications,
Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to userdoc@paradyne.com. Include the
number and title of this document in your correspondence. Please include your name and phone number if you are
willing to provide additional clarification.
Trademarks
ACCULINK, COMSPHERE, FrameSaver, Hotwire, MVL, NextEDGE, OpenLane, Performance Wizard are registered
trademarks of Paradyne Corporation. BitStorm, EtherLoop, ReachDSL, StormPort, StormSystem, StormTracker, and
TruePut are trademarks of Paradyne Corporation. All other products and services mentioned herein are the
trademarks, service marks, registered trademarks, or registered service marks of their respective owners.
A
April 2002
4821-A2-GN20-00
! Important Safety Instructions
1. Read and follow all warning notices and instructions marked on the product or included in the manual.
2. This product is intended to be used with a 3-wire grounding type plug — a plug which has a grounding pin. This is
a safety feature. Equipment grounding is vital to ensure safe operation. Do not defeat the purpose of the grounding
type plug by modifying the plug or using an adapter.
Prior to installation, use an outlet tester or a voltmeter to check the AC receptacle for the presence of earth ground.
If the receptacle is not properly grounded, the installation must not continue until a qualified electrician has
corrected the problem.
If a 3-wire grounding type power source is not available, consult a qualified electrician to determine another
method of grounding the equipment.
3. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to
protect it from overheating, these slots and openings must not be blocked or covered.
4. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power
cord.
5. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous high
voltage points or other risks. Refer all servicing to qualified service personnel.
6. General purpose cables are described for use with this product. Special cables, which may be required by the
regulatory inspection authority for the installation site, are the responsibility of the customer. To reduce the risk of
fire, use a UL Listed or CSA Certified, minimum No. 26 AWG (0.128 mm2) telecommunication cable.
7. When installed in the final configuration, the product must comply with the applicable Safety Standards and
regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory
agencies and inspection authorities to ensure compliance.
8. A rare phenomenon can create a voltage potential between the earth grounds of two or more buildings. If products
installed in separate buildings are interconnected, the voltage potential may cause a hazardous condition.
Consult a qualified electrical consultant to determine whether or not this phenomenon exists and, if necessary,
implement corrective action prior to interconnecting the products.
9. In addition, if the equipment is to be used with telecommunications circuits, take the following precautions:
—
Never install telephone wiring during a lightning storm.
—
Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
—
Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the
network interface.
—
Use caution when installing or modifying telephone lines.
—
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of
electric shock from lightning.
—
Do not use the telephone to report a gas leak in the vicinity of the leak.
10. This product has provisions for the customer to install Class 1 laser transponders which provide optical coupling to
the telecommunication network. Once a Class 1 laser product is installed, the equipment is to be considered to be
a Class 1 Laser Product (Appareil à Laser de Classe 1). The customer is responsible for selecting and installing
the laser transponders and for insuring that the Class 1 AEL (Allowable Emission Limit) per EN/IEC 60825 is not
exceeded after the laser transponders have been installed. Do not install laser products whose class rating is
greater than 1. Refer to all important safety instructions that accompanied the transponder prior to installation.
Only laser Class 1 devices, certified for use in the country of installation by the cognizant agency are to be utilized
in this product.
11. Input power to the ALARM interface (located on the front panel of the enclosure) must not exceed 30V rms or
60V dc.
12. The equipment is intended for installation in a max. 50° C ambient temperature, in an environment that is free of
dust and dirt.
13. The power supply cord for countries other than North America is to be a minimum H05 V V-F type, min. 0.75 mm2,
2-conductor and earth ground terminated in an IEC 320 connector on one end, and a plug which is certified for use
in the country of installation at the other end.
4821-A2-GN20-00
April 2002
B
14. Do not physically stack the Model 4821 units more than eight (8) units high. Physical stability has not been
evaluated for a stack higher than eight units, and a configuration higher than eight units might be unstable and
prone to tipping over. Ensure that the four (4) rubber feet provided with the product have been installed on the
bottom of each unit before stacking one atop another.
EMI Notices
! UNITED STATES – EMI NOTICE:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
The authority to operate this equipment is conditioned by the requirements that no modifications will be
made to the equipment unless the changes or modifications are expressly approved by Paradyne
Corporation.
! CANADA – EMI NOTICE:
This Class A digital apparatus meets all requirements of the Canadian interference-causing equipment
regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du réglement sur le matérial
brouilleur du Canada.
Notices to Users of the Canadian Telephone Network
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is
confirmed by the registration number. The abbreviation IC before the registration number signifies that registration was
performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It
does not imply that Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is labeled on the equipment and includes
the effect of the POTS splitter. The REN assigned to each terminal equipment provides an indication of the maximum
number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of
any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the
devices does not exceed five.
Notice to Users of the United States Telephone Network
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for
Terminal Attachment (ACTA). On the bottom side of this equipment is a label that contains, among other information, a
product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone
company.
This equipment is intended to connect to the Public Switched Telephone Network through the Model 6051 POTS
splitter using a Universal Service Order Code (USOC) type RJ21X jack. Refer to the Installation Instructions for details.
The Ringer Equivalence Number (or REN) is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that
may be connected to a line, as determined by the total RENs, contact the local telephone company. The REN for this
product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point. For example, 03 represents a REN of 0.3.
C
April 2002
4821-A2-GN20-00
If the BitStorm 4800 causes harm to the telephone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will
notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you
believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the
operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
If trouble is experienced with the BitStorm 4800, refer to the repair and warranty information on Page A. If the
equipment is causing harm to the telephone network, the telephone company may request that you disconnect the
equipment until the problem is resolved.
The user may make no repairs to the equipment.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service
commission or corporation commission for information.
If the site has specially wired alarm equipment connected to the telephone line, ensure the installation of the
BitStorm 4800 does not disable the alarm equipment. If you have questions about what will disable alarm equipment,
consult your telephone company or a qualified installer.
Supplier’s Declaration of Conformity
Place of Issue:
Paradyne Corporation
8545 126th Avenue North
Largo, FL 33773-1502
USA
Date of Issue:
3/28/2002
Paradyne Corporation, located at the above address, hereby certifies that the BitStorm 4800, Model Number
4821-AX-XXX, bearing labeling identification number US:AW2HN04B4821 complies with: the Federal Communications
Commission’s (“FCC”) Rules and Regulations 47 CFR Part 68 and the Administrative Council on Terminal Attachments
(“ACTA”)-adopted technical criteria TIA/EIA/IS-968, “Telecommunications – Telephone Terminal Equipment – Technical
Requirements for Connection of Terminal Equipment To the Telephone Network, July 2001.”
Patrick Murphy
Senior Vice President, Chief Financial Officer
CE Marking
When the product is marked with the CE mark, this demonstrates full compliance with the following European
Directives:
„
„
Directive 72/73/EEC: Council Directive of 19 February 1973 on the harmonization of the laws of the member
states relating to electrical equipment designed for use within certain voltage limits, as amended by Directive
93/68EEC.
Directive 89/336/EEC: Council Directive of 3 May 1989 on the approximation of the laws of the member states
relating to Electro-Magnetic Compatibility (EMC), as amended by Directive 93/68/EEC.
4821-A2-GN20-00
April 2002
D
Japan
Class A ITE
This is a Class A product based on the standard of the Voluntary Control Council for interference by Information
Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When
such trouble occurs, the user may be required to take corrective actions.
E
April 2002
4821-A2-GN20-00
Contents
About This Guide
„
„
„
„
1
iii
Document Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iii
Related Product Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv
Related Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv
Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
Cables Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2
Unpacking the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3
Mounting Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5
Rack or Wall Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5
Shelf or Desktop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5
Mounting Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6
Installing the Mounting Brackets for Rack Mounting . . . . . . . . . . . . . .
1-7
Installing the BitStorm 4800 Into a Rack . . . . . . . . . . . . . . . . . . . . . . .
1-8
Installing the Mounting Brackets for Wall Mounting . . . . . . . . . . . . . . .
1-10
Installing the BitStorm 4800 on a Shelf or Desktop . . . . . . . . . . . . . . .
1-12
Installing the Management Module . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-13
Cabling Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
DSL Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2
Downlink GigE Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4
Uplink Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5
Uplink GigE Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6
V.35/X.21 Connector (4804 Management Module) . . . . . . . . . . . .
2-7
Chaining Units Together . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-8
Management Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-9
Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-10
Modem Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-11
Installation
„
„
„
„
„
„
„
„
„
„
„
2
Document Purpose and Intended Audience . . . . . . . . . . . . . . . . . . . .
Cabling
„
„
„
„
„
„
„
„
4821-A2-GN20-00
April 2002
i
Contents
„
„
„
3
2-12
Grounding Lug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-13
Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-14
LED Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1
Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3
System LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
Conventions Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
Using the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2
Logging In to the BitStorm 4800. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3
Setting the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4
Setting the Serial Interface Type and Rate . . . . . . . . . . . . . . . . . . . . .
4-5
LEDs
„
„
„
4
Alarm Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration
„
„
„
„
A Connectors, Cables, and Pin Assignments
„
„
„
„
„
„
„
„
„
„
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-1
Management Port Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-2
Ethernet Uplink and Downlink Connectors. . . . . . . . . . . . . . . . . . . . . .
A-3
Uplink and Downlink – 8-Pin Modular Jacks . . . . . . . . . . . . . . . . .
A-3
Uplink and Downlink – Cable Connectors . . . . . . . . . . . . . . . . . . .
A-3
DSL Network Interface Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-4
V.35/X.21 (EIA-530-A) Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-5
EIA-530-A to X.21 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-6
EIA-530-A to V.35 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-8
Alarm Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-10
Modem Port Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-11
Console Port Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-11
B Equipment List
C Technical Specifications
Index
ii
April 2002
4821-A2-GN20-00
About This Guide
Document Purpose and Intended Audience
This document is written for technicians who install the BitStorm 4800 IP access
concentrator, Model 4821.
Document Summary
Section
Description
Chapter 1, Installation
Describes the physical installation of the BitStorm 4800 into
a rack.
Chapter 2, Cabling
Describes how to install all cables for the BitStorm 4800
and Management Module.
Chapter 3, LEDs
Explains the meaning and usage of the front panel LEDs.
Chapter 4, Configuration
Describes the minimal configuration steps required to
prepare the BitStorm 4800 for remote access.
Appendix A, Connectors,
Cables, and
Pin Assignments
Provides pinouts for all connectors on the BitStorm 4800
and 4800 and 4804 Management Modules.
Appendix B, Equipment List
Provides part numbers for the BitStorm 4800 and related
products.
Appendix C, Technical
Specifications
Lists the technical characteristics of the BitStorm 4800.
Index
Lists key terms, acronyms, concepts, and sections in
alphabetical order.
A master glossary of terms and acronyms used in Paradyne documents is
available on the World Wide Web at www.paradyne.com. Select Library →
Technical Manuals → Technical Glossary.
4821-A2-GN20-00
April 2002
iii
About This Guide
Related Product Documents
Documentation for the BitStorm 4800 IP access concentrator is available on the
World Wide Web at www.paradyne.com. Select Library → Technical Manuals→
BitStorm DSL Products.
Document Number
Document Title
4800-A2-GB20
BitStorm 4800 User’s Guide
Describes how to use the web interface, the command line
interface (CLI), and Simple Network Management Protocol
(SNMP) to configure the BitStorm 4800. Lists and explains all
CLI commands.
4800-A2-GN10
BitStorm 4800 Management Module, Models 4800-B1-000 and
4804-B1-000, Installation Instructions
Describes how to install the 4800 and 4804 Management
Modules in the BitStorm 4800.
6051-A2-GZ40
BitStorm 6051 POTS Splitter Installation Instructions
Describes how to install the POTS splitter card and chassis used
with the BitStorm 4800 in North America.
To order a paper copy of a Paradyne document:
„
„
Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)
Outside the U.S.A., call 1-727-530-8623
Related Specifications
iv
Document Number
Document Title
–
Small Form-factor Pluggable (SFP) Transceiver MultiSource
Agreement (MSA)
ANSI/EIA-310-D-1992
Cabinets, Racks, Panels, and Associated Equipment
IEEE 802.1D
Media Access Control (MAC) Bridges
IEEE 802.1Q
Virtual Bridged Local Area Networks
April 2002
4821-A2-GN20-00
Installation
1
Preparation
Consider the following before installing the BitStorm™ 4800:
„
Installation Site
Your installation site should be well ventilated, clean, and free of
environmental extremes.
„
Installation Options
The BitStorm 4800 may be:
— Mounted with the included mounting brackets in a standard 483 mm (19″)
or 584 mm (23″) rack, or, with separately purchased mounting brackets, in
a 535 mm (21″) ETSI or 610 mm (24″) EIA rack. ETSI brackets are
available from Paradyne. See Appendix B, Equipment List.
As many BitStorm 4800 units may be mounted in a standard rack as there
are 44.45 mm (1.75″ ) spaces in the rack, so long as adequate cooling is
provided.
— Mounted vertically against a wall.
The standard mounting brackets provided can be fastened to the base of
the unit for wall mounting.
— Set on a shelf or desktop.
Up to eight BitStorm 4800 units may be stacked on a shelf or desktop.
„
Management Module
A 4800 or 4804 Management Module must be installed in each BitStorm 4800.
„
Power
The BitStorm 4800 operates from a standard AC power supply (90 to
264 VAC at 47 to 63 Hz).
„
Fiber Optic Uplink and Downlink
Use of either of the fiber optic ports requires use of a Small Form-factor
Pluggable (SFP) transceiver, not included. It must be compliant with the SFP
Transceiver MultiSource Agreement of September 14, 2000, and provide a
1000BaseX interface.
„
Other Cabling
With the exception of the power cord, no cables are provided with the
BitStorm 4800. See Cables Required on page 1-2 to determine what cables
you need to procure before installation.
4821-A2-GN20-00
April 2002
1-1
1. Installation
Cables Required
Table 1-1 shows all the cables that may be required for your installation.
Table 1-1.
Cable Descriptions
Connector Name
Connector and Cable
For Connecting . . .
DSL PORTS 1–24
50-pin RJ21X Telco-type
straight connector and
50-wire cable. Two cables
required for 48 ports.
Up to 24 DSL ports to Main
Distribution Frame,
punchdown block, or splitters.
DOWNLINK GigE (RJ45)
8-position modular plug and
8-wire Category 5 or better
twisted pair cable.
An upstream BitStorm 4800 to
a downstream BitStorm 4800,
or the BitStorm 4800 to an
adjunct server.
DOWNLINK GigE (SFP)
Duplex modular plug and
fiber optic cable. Socket
requires a 1000BaseX SFP
transceiver, not supplied.
An upstream BitStorm 4800 to
a downstream BitStorm 4800,
or the BitStorm 4800 to an
adjunct server.
UPLINK GigE (RJ45)
8-position modular plug and
8-wire Category 5 or better
twisted pair cable.
A downstream BitStorm 4800
to an upstream BitStorm 4800,
or the subtending or only
BitStorm 4800 to the Wide
Area Network (WAN) via an
Ethernet switch.
UPLINK GigE (SFP)
Duplex modular plug and
fiber optic cable. Socket
requires a 1000BaseX SFP
transceiver, not supplied.
A downstream BitStorm 4800
to an upstream BitStorm 4800,
or the subtending or only
BitStorm 4800 to the WAN via
an Ethernet switch.
MGMT
8-position modular plug and
8-wire Category 5 or better
unshielded twisted pair
(UTP) cable.
The BitStorm 4800 to a
Network Management System
over a Local Area Network
(LAN) employing 10BaseT or
100BaseT.
CONSOLE
(4800 and 4804
Management Modules)
DB9 plug connector and
shielded cable. The other
connector depends on the
serial port on your terminal
or PC, but normally is a DB9
socket.
The Management Module to a
terminal or a PC with a
terminal emulation program.
MODEM
(4800 and 4804
Management Modules)
DB9 socket connector and
shielded cable. The other
connector depends on your
modem, but normally is a
DB25 plug.
The Management Module to
an external modem. The
connector can also be used to
connect a terminal or PC.
ALARM
(4800 and 4804
Management Modules)
8-position modular plug and
8-wire cable.
The Management Module to
an alarm system.
V.35/X.21
(4804 Management
Module)
DB25 socket with V.35,
EIA-530-A, or X.21 adapter
or adapter cable.
The subtending or only
BitStorm 4800 to the WAN via
a CSU or router.
DSL PORTS 25–48
1-2
April 2002
4821-A2-GN20-00
1. Installation
Unpacking the Hardware
HANDLING PRECAUTIONS FOR
! STATIC-SENSITIVE DEVICES
This product is designed to protect sensitive components from damage
due to electrostatic discharge (ESD) during normal operation. When
performing installation procedures, however, take proper static control
precautions to prevent damage to equipment. If you are not sure of the
proper static control precautions, contact your nearest sales or service
representative.
The BitStorm 4800 is shipped in a cardboard shipping container. Carefully remove
the unit from its shipping container and check for physical damage. If the unit
shows signs of shipping damage, notify your sales representative.
Package Contents
In addition to this installation guide, the BitStorm 4800 shipping carton should
contain:
„
„
„
„
BitStorm 4800
Mounting brackets (one left and one right)
Power cord
Hardware kit (see Table 1-2, Contents of Hardware Kit Shipped with the
BitStorm 4800)
If anything is missing, notify your sales representative.
Before installing the BitStorm 4800, read the Important Safety Instructions in the
beginning of this document.
Be sure to register your warranty at www.paradyne.com/warranty.
4821-A2-GN20-00
April 2002
1-3
1. Installation
Table 1-2.
Contents of Hardware Kit Shipped with the BitStorm 4800
Appearance
Description
Quantity
Self-retaining nut for racks without threaded holes
5
Dress screw (12-24 x 1/2″ ) for use with self-retaining
nuts
5
Machine screw with captive starwasher (10-32 x 1/2″ )
for use with racks with threaded holes
5
Flat-head screw for attaching mounting brackets to unit 7
1-4
Jackscrew for attaching Telco connectors with short
mounting screws
2
Rubber foot for desk-mount and stacking of units
4
Cable tie (8″) for strain relief and cable management
3
April 2002
4821-A2-GN20-00
1. Installation
Mounting Configurations
Three basic installation configurations are available:
„
„
„
Rack mount
Wall mount
Shelf or desktop
Rack or Wall Mount Installation
The BitStorm 4800 is shipped with mounting brackets suitable for a 483 mm (19″ )
or 584 mm (23″) rack. The same brackets may be used to attach the unit to a wall.
Brackets suitable for a 535 mm (21″ ) rack are available from Paradyne (see
Appendix B, Equipment List), and brackets suitable for a 610 mm (24″) rack can
be obtained from other sources.
NOTE:
In this guide, the term rack refers to any rack, cabinet, frame, or bay suitable
for mounting telecommunications equipment.
Shelf or Desktop Installation
The BitStorm 4800 may also be placed on a shelf or desktop. If you will not mount
the BitStorm 4800 in a rack or on a wall, proceed to Installing the BitStorm 4800
on a Shelf or Desktop on page 1-12.
4821-A2-GN20-00
April 2002
1-5
1. Installation
Mounting Brackets
The right-angle mounting brackets have a long side and a short side.
„
„
„
„
For 483 mm (19″) racks, the long side of a supplied bracket is fastened to the
side of the unit.
For 584 mm (23″ ) racks, the short side of a supplied bracket is fastened to the
side of the unit.
For wall mounting, the long side of a supplied bracket is fastened to the
bottom of the unit.
The optional ETSI brackets are always installed with the short side fastened to
the BitStorm 4800.
Both the supplied brackets and the optional ETSI brackets are marked LEFT SIDE
and RIGHT SIDE, with reference to the left and right sides of the BitStorm 4800
when viewed from the front.
For wall mounting, proceed to Installing the Mounting Brackets for Wall Mounting
on page 1-10.
For rack mounting, proceed to Installing the BitStorm 4800 Into a Rack on
page 1-8.
1-6
April 2002
4821-A2-GN20-00
1. Installation
Installing the Mounting Brackets for Rack Mounting
Procedure
To install the mounting brackets for rack mounting:
1. Identify the flat-head screws provided in the hardware kit. Six screws are
required for the 483 mm (19″) configuration, and four screws for the other
configurations.
2. Attach the brackets appropriate to your rack size. Tighten all screws firmly.
483 mm (19 inch) Rack Mount
with Supplied Brackets
535 mm (21.1 inch) Rack Mount
with Optional ETSI Brackets
4821-A2-GN20-00
April 2002
584 mm (23 inch) Rack Mount
with Supplied Brackets
02-17067
1-7
1. Installation
Installing the BitStorm 4800 Into a Rack
Two types of mounting screws are provided. Use:
„
„
#10-32 mounting screws for rails with threaded screw holes
#12-24 mounting screws and self-retaining nuts for rails with unthreaded
screw holes
Procedure
To install the BitStorm 4800 into a rack:
1. Determine where in the rack you will mount the BitStorm 4800. If your rack
does not have threaded screw holes, slip self-retaining nuts onto the rails
where the BitStorm 4800 will be fastened.
02-17070
1-8
April 2002
4821-A2-GN20-00
1. Installation
2. Place the BitStorm 4800 so that the brackets rest against the front of the rails.
Insert screws in the bottom screw positions and hand-tighten them.
3. Insert and tighten the screws in the top screw positions, then tighten the
bottom screws.
V.35/X.21
OK
ALARM
TEST
1
2
3
4
5
6
7
8
9
10
11
12
ALARM
13
14
15
16
17
18
19
20
21
22
MODE
M
23
24
25
26
27
28
CONSOL
E
29
30
MGMT
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
UPLIN
K
GigE
DOWN
LIN
GigE K
1
2
3
4
5
6
7
8
STACK
POS
ITION
V.35/X.21
ALARM
MODEM
4804
OK
ALARM
TEST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
CONSOLE
MGMT
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
UPLINK
GigE
DOWN LINK
GigE
47
48
4821
1
STACK POSITION
2
3
4
5
6
7
8
02-17071
4. Do not plug in the unit. Proceed to Installing the Management Module on
page 1-13.
4821-A2-GN20-00
April 2002
1-9
1. Installation
Installing the Mounting Brackets for Wall Mounting
Wall mounting requires two wood screws suitable for the weight of the fully cabled
unit. These are not included. Use at a minimum 6 mm (.25″ ) diameter screws in
19 mm (.75″ ) plywood.
Procedure
To install the mounting brackets for wall mounting:
1. Identify the flat-head screws provided in the hardware kit. Two screws are
required for each bracket.
2. Orient the unit so that the bottom is facing you and the faceplate is at the top.
3. Locate the supplied Right Side mounting bracket and fasten it to the right side
of the unit.
02-17146
4. Locate the supplied Left Side mounting bracket and fasten it to the left side of
the unit.
5. Tighten all screws firmly.
1-10
April 2002
4821-A2-GN20-00
1. Installation
6. Install two wood screws (not provided) at the same height at least 760 mm
(30″ ) above the floor and 453 mm (17.85″) apart. Do not completely tighten
the screws. Leave them so their heads are about 6 mm (.25″ ) from the wall.
453 mm (17.85 in)
02-17147
7. Hang the unit from the wood screws to verify that the screws are properly
placed. The screws should freely slide into the top of the key slots in the
brackets.
8. Do not fasten the unit to the wall until after it is completely cabled and tested.
Proceed to Installing the Management Module on page 1-13.
4821-A2-GN20-00
April 2002
1-11
1. Installation
Installing the BitStorm 4800 on a Shelf or Desktop
If the BitStorm 4800 will be placed on a shelf or desktop, install the provided
rubber feet before putting the BitStorm 4800 in position.
Procedure
To install the BitStorm 4800 on a shelf or desktop, as a standalone unit or in a
stack:
1. Locate the rubber feet in the hardware kit provided with the BitStorm 4800.
2. Turn the BitStorm 4800 upside down on a work surface. Squares stamped into
the bottom of the BitStorm 4800 show the proper positions for the feet.
3. Remove the protective sheet from the bottom of each foot, then press the foot
onto a corner of the bottom of the BitStorm 4800.
RTS 25
DSL PO
DSL PO
-48
RTS 1-2
4
02-17072
4. Turn the BitStorm 4800 right side up and place it in position on a shelf or
desktop.
If the installation includes more than one unit, one can be stacked atop
another. Up to eight units can be stacked together.
5. Do not plug in the unit. Proceed to Installing the Management Module on
page 1-13.
1-12
April 2002
4821-A2-GN20-00
1. Installation
Installing the Management Module
Each BitStorm 4800 requires a Model 4800 Management Module or a Model 4804
Management Module with V.35/X.21 uplink. If your Management Module was
shipped separately from the BitStorm 4800, install the Management Module
before you connect the BitStorm 4800 to a power source.
HANDLING PRECAUTIONS FOR
! STATIC-SENSITIVE DEVICES
This product is designed to protect sensitive components from damage
due to electrostatic discharge (ESD) during normal operation. When
performing installation procedures, however, take proper static control
precautions to prevent damage to equipment. If you are not sure of the
proper static control precautions, contact your nearest sales or service
representative.
Procedure
To install a Management Module:
1. Remove the two screws holding the slot cover on the BitStorm 4800.
OK
ALARM
TEST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
MGMT
33
34
35
36
37
38
39
40
41
42
43
44
45
46
UPLIN
K
GigE
47
48
02-17068
2. Store the slot cover; retain the screws.
4821-A2-GN20-00
April 2002
1-13
1. Installation
3. Slide the Management Module into the guide rails just inside the opening.
Press the Management Module firmly into place until it is fully seated and the
faceplate of the Management Module is flush against the faceplate of the
BitStorm 4800.
Guide Rails
OK
ALARM
V.35/X.2
1
4804
TEST
1
2
3
4
5
6
ALARM
7
8
9
10
11
12
13
14
MODEM
15
16
17
18
19
20
21
22
23
24
CONSO
LE
25
26
27
28
29
30
31
32
MGMT
33
34
35
36
37
38
39
40
41
42
43
44
45
46
UPLIN
K
GigE
47
48
02-17069
4. Replace and fasten the two screws.
Do not plug in the unit. Proceed to Chapter 2, Cabling.
1-14
April 2002
4821-A2-GN20-00
Cabling
2
Cabling Overview
The BitStorm 4800 has a large variety of possible cabling configurations. This
chapter describes all possible connections, not all of which are required:
„
„
„
DSL Ports on page 2-2
Downlink GigE Connectors on page 2-4
Uplink ports:
— Uplink GigE Connectors on page 2-6
— V.35/X.21 Connector (4804 Management Module) on page 2-7
„
„
„
„
„
„
4821-A2-GN20-00
Chaining Units Together on page 2-8
Console Port on page 2-10
Modem Port on page 2-11
Alarm Port on page 2-12
Grounding Lug on page 2-13
Power Cord on page 2-14
April 2002
2-1
2. Cabling
DSL Ports
The BitStorm 4800 has two DSL connectors, each supporting the tip and ring
connections of up to 24 DSL ports over a 50-position cable. These must be
connected to a POTS (plain old telephone service) splitter.
In North America, the BitStorm 6051 POTS Splitter must be used. (See the
BitStorm 6051 POTS Splitter Installation Instructions for information.) Elsewhere
the splitter must conform to all regional regulatory requirements.
Procedure
To cable the DSL Ports:
1. Insert a cable tie (provided) through the top of the anchor mount next to the
DSL PORTS 1–24 connector.
2. If the connector for your cable has a long captive screw, attach it to the DSL
PORTS 1–24 connector and fasten it with the captive screw.
Anchor
Mount
Long
Screw
50-Pin
Connector
02-17082
3. If the connector for your cable has a short captive screw, install the provided
jack screw in the threaded hole next to the DSL PORTS 1–24 connector.
Attach the cable to the DSL PORTS 1–24 connector and fasten it to the jack
screw with its short captive screw.
#4-40
Jack Screw
Anchor
Mount
Short
Screw
50-Pin
Connector
2-2
April 2002
02-17083
4821-A2-GN20-00
2. Cabling
4. Tighten the cable tie around the connector and trim the excess.
02-17084
5. If ports 25–48 are used, repeat Step 1 through Step 4, substituting
DSL PORTS 25–48 for DSL PORTS 1–24.
6. Connect the 48 tip and ring connections to a POTS splitter. See the
documentation that came with your POTS splitter for more information.
7. Secure the cables as required for strain relief.
TS 25-4
DSL POR
POTS Splitter
Card in 1-Slot
Chassis
8
TS 1-24
DSL POR
BitStorm 4800
Rear
UPLINK
GigE
K
DOWNLIN
GigE
STACK
POSIT
ION
Front
02-17158
4821-A2-GN20-00
April 2002
2-3
2. Cabling
Downlink GigE Connectors
There are two DOWNLINK GigE connectors on the unit. Only one can be active.
For the wire connection, either a straight-through or a crossover cable can be
used. The wiring is automatically detected and, if necessary, compensated for.
A DOWNLINK GigE connector can be used to connect to:
„
„
An adjunct server to provide caching, video on demand, or gateway services
The UPLINK GigE connector of a downstream BitStorm 4800 (see Chaining
Units Together on page 2-8)
Procedure
To attach an adjunct server:
1. Determine the interface type to be used (wire or fiber), and procure the
appropriate copper cable, or fiber optic cable and SFP transceiver.
2. For a wire connection, plug the 8-position modular plug into the DOWNLINK
GigE modular jack.
MGMT
UPLIN
K
GigE
DOWN
LIN
GigE K
1
8-Position
Modular
Plug
02-17150
3. For a fiber connection, plug your transceiver into the DOWNLINK GigE SFP
socket. Plug your fiber optic cable into the cable socket of the transceiver.
MGMT
UPLIN
K
GigE
DOWN
LIN
GigE K
1
SFP
Transceiver
LC
Connector
02-17148
4. Connect the other end of the cable to your adjunct server.
2-4
April 2002
4821-A2-GN20-00
2. Cabling
Uplink Options
The Wide Area Network (WAN) uplink can be:
„
„
Provided by an upstream BitStorm 4800 (see Chaining Units Together on
page 2-8)
An Ethernet switch, connected to the UPLINK GigE modular jack on the
BitStorm 4800, or to a Small Form-factor Pluggable (SFP) transceiver plugged
into the UPLINK GigE SFP socket, providing the appropriate interface:
— 100BaseFX
— 100BaseTX
— 1000BaseT
— 1000BaseSX
— 1000BaseLX
„
A CSU or router with an integral CSU connected to the V.35/X21 connector of
the 4804 Management Module with an adapter or adapter cable, if necessary,
providing the appropriate interface:
— V.35
— EIA-530-A
— X.21
4821-A2-GN20-00
April 2002
2-5
2. Cabling
Uplink GigE Connectors
There are two UPLINK GigE connectors on the unit. Only one can be active. For
the wire connection, either a straight-through or a crossover cable can be used.
The wiring is automatically detected and, if necessary, compensated for.
Procedure
To connect to an Ethernet switch:
1. Determine the interface type, and procure the appropriate copper cable, or
fiber optic cable and SFP transceiver.
2. For a wire connection, plug the 8-position modular plug into the UPLINK
GigE modular jack.
MGMT
UPLIN
K
GigE
DOWN
LIN
GigE K
1
8-Position
Modular
Plug
02-17149
3. For a fiber connection, plug your transceiver into the UPLINK GigE SFP
socket. Plug your fiber optic cable into the cable socket of the transceiver.
MGMT
UPLIN
K
GigE
DOWN
LIN
GigE K
1
SFP
Transceiver
02-17076
LC
Connector
4. Connect the other end of the cable to the Ethernet switch.
2-6
April 2002
4821-A2-GN20-00
2. Cabling
V.35/X.21 Connector (4804 Management Module)
Procedure
To connect to a CSU or router:
1. Determine the electrical interface required: V.35, EIA-530-A, or X.21.
2. Connect the appropriate adapter or adapter cable to the V.35/X.21 connector
of the 4804 Management Module.
3. Fasten the connector to the Management Module with its captive screws.
4. If you are using a short adapter and a separate cable, connect a cable to the
adapter and fasten the two together with screws or cable ties.
5. If the BitStorm 4800 is in a rack, dress the cable to the left side of the rack, and
fasten it to the rail with cable ties.
6. Connect the other end of the cable to the CSU or router. Fasten the connector
to the CSU or router with its captive screws or a cable tie.
Router
V.35/X.2
1
ALARM
4804
OK
ALARM
TEST
1
2
3
4
5
6
MODEM
CONSOL
E
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
MGMT
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
02-17078
The default interface for the BitStorm 4800 software is V.35. If you use a V.35
interface you do not need to configure the software to accommodate it. For an
EIA-530-A or X.21 interface, see Chapter 4, Configuration.
4821-A2-GN20-00
April 2002
2-7
2. Cabling
Chaining Units Together
Up to eight BitStorm 4800 units may be chained together by their UPLINK and
DOWNLINK ports. One unit provides the uplink for the stack.
Procedure
To chain together a group of BitStorm 4800 units:
1. Plug an 8-pin modular cable into the DOWNLINK GigE jack of the
BitStorm 4800 that will provide the uplink.
2. Plug the other end of the cable into the UPLINK GigE jack of the next
BitStorm 4800 in the stack.
3. If there is another BitStorm 4800 below this one in the logical stack, plug an
8-pin modular cable into the DOWNLINK GigE jack of this BitStorm 4800.
4. Repeat Step 2 and Step 3 until all units in the stack are cabled together.
V.35/X.21
ALARM
4804
OK
ALARM
OK
ALARM
OK
ALARM
1
2
TEST
1
2
TEST
TEST
3
4
1
2
5
6
3
4
3
4
7
8
5
6
5
6
7
8
7
8
9
10
9
10
9
10
11
12
11
12
11
12
13
14
13
14
13
14
15
16
17
18
19
20
21
22
MODE
M
23
24
25
26
27
28
CONSOL
E
MGMT
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
UPLIN
K
GigE
47
48
DOWN
LIN
GigE K
1
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MGMT
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
UPLIN
K
GigE
47
48
2
1
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MGMT
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
UPLIN
K
GigE
3
4
5
6
7
8
STACK
POS
ITION
DOWN
LIN
GigE K
2
3
4
5
6
7
8
STACK
POS
ITION
DOWN
LIN
GigE K
1
2
3
4
5
6
7
8
STACK
POS
ITION
02-17077
In Release 1, all units must have a Management Module installed.
2-8
April 2002
4821-A2-GN20-00
2. Cabling
Management Port
The MGMT (management) port can be used to connect the BitStorm 4800 to a
network management system using a 10BaseT or 100BaseT LAN. The MGMT
port is isolated and no user data is accessible over it.
Either a straight-through or a crossover cable can be used. The wiring is
automatically detected and, if necessary, compensated for.
Procedure
To use the MGMT port:
1. Connect a modular 8-pin cable to the MGMT port.
2. If the BitStorm 4800 is in a rack, fasten the cable to a rail with a cable tie.
3. Connect the other end of the cable to your Ethernet hub or to a network
interface card in a PC.
Hub Device
V.35/X.2
1
ALARM
4804
OK
ALARM
TEST
1
2
3
4
5
6
MODEM
CONSOL
E
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
MGMT
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
02-17085
4821-A2-GN20-00
April 2002
2-9
2. Cabling
Console Port
The CONSOLE port on the Management Module normally serves as the primary
user interface with the BitStorm 4800 during installation.
Procedure
To connect a terminal or PC to the CONSOLE port:
1. Configure the terminal or terminal emulation program to use the following
parameters:
— Maximum speed: 9600 bps
— Data bits: 8
— Parity: None
— Stop bits: 1
2. Determine and procure the proper Data Terminal Equipment (DTE) cable type.
The CONSOLE port requires a DB9 plug connector. The other connector
depends on the serial port on your terminal or PC.
3. Connect the DB9 plug connector to the CONSOLE port socket. The
CONSOLE port is ordinarily used only during installation, so do not fasten the
connector.
4. Connect the other end of the cable to the serial port of your terminal or PC.
Serial
Port
V.35/X.2
1
ALARM
4804
OK
ALARM
TEST
1
2
3
4
5
6
MODEM
CONSOL
E
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
MGMT
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
02-17075
2-10
April 2002
4821-A2-GN20-00
2. Cabling
Modem Port
The MODEM port on the Management Module can be used to attach a modem for
remote dial-in management of the BitStorm 4800. The MODEM port can also be
used to attach a terminal or PC to the Management Module using a Data
Communications Equipment (DCE) cable.
Procedure
To connect a modem to the MODEM port:
1. Determine and procure the proper DCE cable type. The MODEM port requires
a DB9 socket connector. The other connector depends on the serial port on
your modem, but normally a DB25 plug is required.
2. Connect the DB9 socket connector to the MODEM port socket.
3. If the modem will be permanently connected, fasten the connector to the
Management Module with its captive screws. If the BitStorm 4800 is in a rack,
dress the cable to the left and attach it to the rail with a cable tie.
4. Connect the other end of the cable to the serial port of your modem.
Serial Port
Modem
PWR
ALM
TST
LINE
ETHER
NET
V.35/X.2
1
ALARM
4804
OK
ALARM
TEST
1
2
3
4
5
6
MODEM
CONSOL
E
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
MGMT
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
02-17074
4821-A2-GN20-00
April 2002
2-11
2. Cabling
Alarm Port
The ALARM port provides a normally-on circuit and a normally-off circuit that
reverse their states in response to an alarm. This interface can be used to set off a
physical alarm.
Procedure
To use the ALARM port:
1. Connect a modular 8-pin cable to the ALARM port.
2. If the BitStorm 4800 is in a rack, dress the cable to the left and secure it to the
rail with a cable tie.
3. Connect the other end of the cable to your alarm monitoring system.
CO Alarm
Monitoring System
V.35/X.2
1
ALARM
4804
OK
ALARM
TEST
1
2
3
4
5
6
MODEM
CONSOL
E
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
MGMT
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
02-17079
2-12
April 2002
4821-A2-GN20-00
2. Cabling
Grounding Lug
Procedure
To connect the unit to a ground:
1. Strip back the insulation approximately 8 mm (5/16″ ) on 14 AWG (2.08 mm2)
copper ground wire.
2. Loosen the screw on the grounding lug located on the back panel next to the
power switch.
3. Insert the stripped end of the wire through the bottom of the grounding lug and
tighten the screw. Ensure that the screw makes contact with the stripped
portion of the wire.
4. Attach the ground wire to an earth ground.
-48
RTS 25
DSL PO
4
RTS 1-2
DSL PO
To
Ground
02-17081
4821-A2-GN20-00
April 2002
2-13
2. Cabling
Power Cord
The BitStorm 4800 can be powered by any AC source providing 90 to 264 VAC at
47 to 63 Hz.
Procedure
To connect the BitStorm 4800 to a power source:
1. Verify that the switch on the rear panel is in the Off (0) position.
2. Insert the power cord into the socket under the switch.
3. If the BitStorm 4800 is in a rack, dress the power cord to the left and fasten it
to the rail with a cable tie.
4. Connect the other end of the power cord to a grounded AC power source.
5. Press the On (1) position of the switch to turn on the BitStorm 4800.
4
RTS 1-2
DSL PO
02-17080
When power is appplied to the BitStorm 4800, the front panel Light-Emitting
Diodes (LEDs) convey the state of the unit and its interfaces. See Chapter 3,
LEDs.
2-14
April 2002
4821-A2-GN20-00
LEDs
3
LED Locations
The small black rectangles in the following illustrations denote the locations of the
front panel LEDs, including the LED on the 4804 Management Module.
V.35/X.2
1
ALARM
4804
OK
ALARM
TEST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
MODEM
23
24
25
26
27
28
29
30
CONSOL
E
31
32
MGMT
33
34
35
36
37
38
39
40
41
42
43
44
45
46
UPLINK
GigE
47
48
DOWNLIN
GigE K
1
ALARM
V.35/X.21
2
3
4
5
6
7
8 STACK
POSITI
ON
MODEM
CONSOLE
4804
OK
ALARM
TEST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
02-17086
Figure 3-1.
4821-A2-GN20-00
V.35/X.21, System, and DSL Port LEDs
April 2002
3-1
3. LEDs
V.35/X.2
1
ALARM
4804
OK
ALARM
TEST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
MODEM
23
24
25
26
27
28
29
30
CONSOL
E
31
32
MGMT
33
34
35
36
37
38
39
40
41
42
43
44
45
46
UPLINK
GigE
47
48
DOWNLIN
GigE K
1
MGMT
UPLINK
GigE
2
3
4
5
6
7
8 STACK
POSITI
ON
DOWNLINK
GigE
1
2
3
4
5
6
7
8 STACK POSITION
02-17087
Figure 3-2.
3-2
MGMT, UPLINK, DOWNLINK, and Stack Position LEDs
April 2002
4821-A2-GN20-00
3. LEDs
Front Panel LEDs
When power is first applied to the BitStorm 4800 it performs a self-test. When this
test is successfully completed, the OK LED lights. The meaning of all the LEDs is
as shown in Table 3-1, Front Panel LEDs.
Table 3-1.
Front Panel LEDs
LED
Color
State
Meaning
ALARM
Amber
Off
No Alarms.
On
Unit failed self-test, or the unit has exceeded a
safe temperature, or a fan has failed.
Off
The port is disabled, or no physical connection
exists.
On
A physical connection is detected.
Off
The port is disabled or no signal is detected on
the line.
On
Port has successfully trained with the remote and
is active.
Blinking
Port is attempting to train.
Off
The port is disabled, or no physical connection
exists.
On
A physical connection is detected.
Off
No power, or the unit has not completed
initialization.
On
Unit has power and has completed initialization.
DOWNLINK
DSL Port
(1–48)
MGMT
OK
Green
Green
Green
STACK
POSITION
Green
On
Indicates the logical position in a stack of up to
eight units. (Future use.)
TEST
Amber
Off
Normal operating mode.
On
At least one port is in test mode.
Off
The port is disabled, or no physical connection
exists.
On
A physical connection is detected.
Off
The port is disabled, or no physical connection
exists.
On
A physical connection is detected.
Blinking
The port is in test mode.
UPLINK
V.35
(on 4804
Management
Module only)
4821-A2-GN20-00
Green
Green
Green
April 2002
3-3
3. LEDs
System LEDs
The three system LEDs, OK, TEST, and ALARM, have meaning at all times, as
shown in Table 3-2, System LEDs.
Table 3-2.
3-4
System LEDs
OK
ALARM
TEST
Description
Off
Off
Off
Unit is powered Off.
Off
Off
ON
Unit Failed – LEDs should never be in this state.
Notify your service representative.
Off
ON
Off
Unit Failed – The unit has power, but never
completed its initialization process. Notify your
service representative.
Off
ON
ON
Self-Test – The LEDs should be in this state
only during self-test, immediately after the unit is
turned on.
ON
Off
Off
Normal Operation – Unit has successfully
passed self-test, there are no alarms in the
system, and none of the ports is in test mode.
ON
Off
ON
Test Mode – At least one port is in test mode.
ON
ON
Off
Alarm – Unit has failed self-test, or a major
alarm condition exists. Notify your service
representative.
ON
ON
ON
Alarm – At least one port is in test mode, and a
major alarm condition exists. Notify your service
representative.
April 2002
4821-A2-GN20-00
Configuration
4
Overview
The BitStorm 4800 is designed to require minimal configuration before it can be
accessed by a Network Operations Center (NOC). You may need to configure:
„
„
„
„
The IP address for the Management Module if the default address
(10.10.10.10) is not usable
The default gateway address
The data rate for the V.35/X.21 port, if used
The serial interface type for the V.35/X.21 port if you use an EIA-530-A or X.21
uplink
Initial configuration can be performed using the Command Line Interface (CLI).
The CLI is available from a terminal or PC connected to the CONSOLE port of the
Management Module.
See the BitStorm 4800 User’s Guide for detailed information about the CLI.
Conventions Used
In this book, the Enter key means whatever key you use to submit data to your
terminal or PC. It may be called the Return key on older devices.
Characters displayed on your screen, including those you type, are shown in the
Courier font in this book.
4821-A2-GN20-00
April 2002
4-1
4. Configuration
Using the CLI
The CLI provides automatic command completion. You need to type only enough
of a command to make it unique. The CLI then completes each word in the
command.
For example, if you enter:
sh man i
the CLI expands it to:
show management ip
You can obtain help with CLI commands by typing a ? (question mark). A question
mark alone lists all commands. A command followed by a question mark lists all
usages of the command.
For example, if you enter:
sh ?
the CLI lists all the possible show commands.
4-2
April 2002
4821-A2-GN20-00
4. Configuration
Logging In to the BitStorm 4800
When the BitStorm 4800 is turned on, the following prompt is displayed on the
terminal:
Login>
Procedure
To log in to the BitStorm 4800:
1. Type admin at the login prompt and press Enter. The following prompt is
displayed:
Password>
2. The default user password is null, so simply press Enter. The following prompt
is displayed:
IAC>
IAC stands for IP Access Concentrator.
3. Type privilege and press Enter to enter administrator mode. The following
prompt is displayed:
Password>
4. The default administrator password is null, so simply press Enter. The
following prompt is displayed:
IAC#
This shows that you are in administrator mode.
4821-A2-GN20-00
April 2002
4-3
4. Configuration
Setting the IP Address
The IP address of the Management Module must be set before the BitStorm 4800
can be remotely managed.
Procedure
To set the IP address of the Management Module:
1. At the IAC# prompt, type:
configure management address address mask gateway
Where:
— address is the IP address to be assigned to the Management Module
— mask is the IP subnet mask for the specified address
— gateway is the default gateway IP address
For example:
conf man addr 135.26.10.37 255.255.255.0 135.26.10.254
2. Press Enter. The prompt changes to IAC#! to show that the configuration
change has yet to be saved.
3. Type save and press Enter.
4. To verify that the address has been set, type:
show management ip
The CLI displays the IP address, subnet mask, and default gateway address.
4-4
April 2002
4821-A2-GN20-00
4. Configuration
Setting the Serial Interface Type and Rate
The 4804 Management Module has a DB25 interface (labeled V.35/X.21) that can
be defined as V.35 (the default), EIA-530-A, or X.21. If you intend to use the
connector for a V.35 or X.21 uplink, you must change the software setting.
The V.35/X.21 port has a default rate of 2048 Kbps. You must change the setting if
the interface is configured for internal clocking and you require a different rate.
Procedure
To set the serial interface type and rate for the V.35/X.21 uplink port:
1. At the IAC# prompt, type:
configure interface v35 type interface_type
Where:
— interface_type is the type of interface required by the device connected to
the V.35/X.21 uplink port. It must be one of:
— eia530a
— v35
— x21
For example:
conf int v35 typ x
2. Press Enter. The prompt changes to IAC#! to show that the configuration
change has yet to be saved.
3. At the IAC#! prompt, type:
configure interface v35 rate data_rate
Where:
— data_rate is the rate in Kbps. It must be a multiple of 8 between 64 and
8192.
For example:
conf int v35 ra 1536
4. Type save and press Enter.
5. To verify that the type and rate have been set, type:
show int v35 conf
The CLI displays all configuration options for the V.35/X.21 uplink port,
including the type and rate.
4821-A2-GN20-00
April 2002
4-5
4. Configuration
4-6
April 2002
4821-A2-GN20-00
Connectors, Cables, and
Pin Assignments
A
Overview
The following sections provide pin assignments for:
„
„
„
„
„
„
„
„
„
Management Port Connector on page A-2
Ethernet Uplink and Downlink Connectors on page A-3
DSL Network Interface Cable on page A-4
V.35/X.21 (EIA-530-A) Port on page A-5
EIA-530-A to X.21 Interface on page A-6
EIA-530-A to V.35 Interface on page A-8
Alarm Port on page A-10
Modem Port Connector on page A-11
Console Port Connector on page A-11
ALARM
V.35/X.21
MODEM
CONSOLE
MGMT
OK
ALARM
TEST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
UPLINK
GigE
47
48
DOWNLINK
GigE
1
2
3
4
5
6
8 STACK POSITION
7
02-17065-01
Figure A-1.
BitStorm 4800 Front Panel (with 4804 Management Module)
DSL PORTS 1-24
DSL PORTS 25-48
02-17066-01
Figure A-2.
4821-A2-GN20-00
BitStorm 4800 Rear Panel
April 2002
A-1
A. Connectors, Cables, and Pin Assignments
Management Port Connector
The Management (MGMT) connector is an 8-pin
unkeyed modular jack for a 10/100BaseT
management interface. Either a straight-through
or a crossover cable can be used. The wiring is
automatically detected and, if necessary,
compensated for.
Table A-1.
A-2
Pin 1
Pin 8
97-15449
Management Port Pinouts
Signal
Pin
Transmitted Data +
1
Transmitted Data –
2
Received Data +
3
Unused
4
Unused
5
Received Data –
6
Unused
7
Unused
8
April 2002
4821-A2-GN20-00
A. Connectors, Cables, and Pin Assignments
Ethernet Uplink and Downlink Connectors
Ethernet UPLINK and DOWNLINK ports are provided in two forms: 8-pin modular
jacks, and sockets for Small Form-factor Pluggable (SFP) transceivers. For the
wire connection, either a straight-through or a crossover cable can be used. The
wiring is automatically detected and, if necessary, compensated for.
Uplink and Downlink – 8-Pin Modular Jacks
The UPLINK and DOWNLINK wire connectors are
8-pin unkeyed modular jacks for 1000BaseT.
Table A-2.
Uplink and Downlink Pinouts
Pair
Tip/Ring
Designation
Pin
1
Tip (+)
1
1
Ring (–)
2
2
Tip (+)
3
3
Tip (+)
4
3
Ring (–)
5
2
Ring (–)
6
4
Tip (+)
7
4
Ring (–)
8
Pin 1
Pin 8
97-15449
Uplink and Downlink – Cable Connectors
The UPLINK and DOWNLINK SFP sockets accept SFP transceivers compliant
with the SFP Transceiver MultiSource Agreement of September 14, 2000. The
SFP transceivers provide cable jacks for 1000BaseLX or 1000BaseSX
connections. See the specifications of your transceiver for more information.
4821-A2-GN20-00
April 2002
A-3
A. Connectors, Cables, and Pin Assignments
DSL Network Interface Cable
The 50-pin RJ21X Telco connectors at the rear of
the BitStorm 4800 provide the 2-wire loop interface
from each DSL port to the demarcation point. (The
Canadian designation for this connector is
CA21A.) There is one connector or two connectors
depending on whether the BitStorm 4800 supports
24 or 48 DSL ports, respectively.
Table A-3, DSL Connector Pinouts, lists the pin
assignments for each of these interfaces. Note that
Pins 25 and 50 are not used.
Table A-3.
A-4
1
25
50
26
02-17151
DSL Connector Pinouts
DSL Port
Connector Pins
(Tip, Ring)
1
1, 26
2
2, 27
3
3, 28
4
4, 29
5
5, 30
6
6, 31
7
7, 32
8
8, 33
9
9, 34
10
10, 35
11
11, 36
12
12, 37
13
13, 38
14
14, 39
15
15, 40
16
16, 41
17
17, 42
18
18, 43
19
19, 44
20
20, 45
21
21, 46
22
22, 47
23
23, 48
24
24, 49
April 2002
4821-A2-GN20-00
A. Connectors, Cables, and Pin Assignments
V.35/X.21 (EIA-530-A) Port
The V.35/X.21 port is on the faceplate of the 4804 Management Module. It
provides the EIA-530-A interface shown in Table A-4, V.35/X.21 (EIA-530-A) Port
Interface Connector.
Table A-4.
V.35/X.21 (EIA-530-A) Port Interface Connector
Circuit
ITU-T
Mnemonic Number
Signal
4821-A2-GN20-00
Direction
Pin
Shield
—
—
—
1
Signal Common
AB
102A
—
7
Signal Common
AC
102B
—
23
Transmitted Data
BA
103
To DSU/CSU
2 (A)
14 (B)
Received Data
BB
104
From DSU/CSU
3 (A)
16 (B)
Request to Send
CA
105
To DSU/CSU
4 (A)
19 (B)
Clear to Send
CB
106
From DSU/CSU
5 (A)
13 (B)
Received Line Signal Detector
CF
109
From DSU/CSU
8 (A)
10 (B)
DCE Ready
CC
107
From DSU/CSU
6
DTE Ready
CD
108/1, /2
To DSU/CSU
20
Transmit Signal Element
Timing (DTE Source)
DA
113
To DSU/CSU
11 (B)
24 (A)
Transmit Signal Element
Timing (DCE Source)
DB
114
From DSU/CSU
12 (B)
15 (A)
Receiver Signal Element
Timing (DCE Source)
DD
115
From DSU/CSU
17 (A)
9 (B)
Local Loopback
LL
141
To DSU/CSU
18
Remote Loopback
RL
140
To DSU/CSU
21
Test Mode
TM
142
From DSU/CSU
25
April 2002
A-5
A. Connectors, Cables, and Pin Assignments
EIA-530-A to X.21 Interface
The EIA-530-A to X.21 adapter (4800-F1-502) or adapter cable (4800-F1-503)
are DB25-to-DB15 connectors that, connected to the V.35/X.21 port of the
4804 Management Module, provide the X.21 interface shown in Table A-5, X.21
Cable Interface.
Pin 25
Pin 1
Pin 1
02-17090
Pin 15
530 DB25
SIGNAL SOCKET
TD-A
TD-B
RD-A
RD-B
RXC-A
RXC-B
RTS-A
RTS-B
RLSD-A
RLSD-B
SIG. COMMON
TT-A
TT-B
DB15
PLUG
2
14
3
16
17
9
4
19
8
10
7
24
11
2
9
4
11
6
13
3
10
5
12
8
7
14
X.21
SIGNAL
TD-A
TD-B
RD-A
RD-B
RXC-A
RXC-B
RTS-A
RTS-B
RLSD-A
RLSD-B
SIG. COMMON
TT-A
TT-B
02-17091
Figure A-3.
A-6
EIA-530-A to X.21 Adapter and Adapter Cable Pinouts
April 2002
4821-A2-GN20-00
A. Connectors, Cables, and Pin Assignments
Table A-5.
X.21 Cable Interface
ITU-T
Number
Signal
4821-A2-GN20-00
Direction
Pin
Signal Common
102
—
Transmitted Data
103
To DSU/CSU
2 (A)
9 (B)
Received Data
104
From DSU/CSU
4 (A)
11 (B)
Request to Send
105
To DSU/CSU
3 (A)
10 (B)
Data Channel Received Line Signal Detector
109
From DSU/CSU
5 (A)
12 (B)
Transmit Signal Element Timing (DTE Source)
113
To DSU/CSU
7 (A)
14 (B)
Receiver Signal Element Timing (DCE Source)
115
From DSU/CSU
6 (A)
13 (B)
April 2002
8
A-7
A. Connectors, Cables, and Pin Assignments
EIA-530-A to V.35 Interface
The EIA-530-A to V.35 adapter (4800-F1-500) and adapter cable (4800-F1-501)
are DB25-to-MS34 connectors that, connected to the V.35/X.21 port of the
4804 Management Module, provide the V.35 interface shown in Table A-6, V.35
Cable Interface.
Pin 25
Pin 1
A
MM
B
NN
530 DB25
SIGNAL SOCKET
SHIELD
TD-A
TD-B
RD-A
RD-B
TXC-A
TXC-B
RXC-A
RXC-B
RTS
CTS
RLSD
DSR
SIG. COMMON
TT-A
TT-B
DTR
RL
LL
TM
SIG. COMMON
02-17088
MS34
PLUG
1
2
14
3
16
15
12
17
9
4
5
8
6
7
24
11
20
21
18
25
23
A
P
S
R
T
Y
AA
V
X
C
D
F
E
B
U
W
H
N
L
NN
V.35
SIGNAL
SHIELD
TD-A
TD-B
RD-A
RD-B
TXC-A
TXC-B
RXC-A
RXC-B
RTS
CTS
RLSD
DSR
SIG. COMMON
TT-A
TT-B
DTR
RL
LL
TM
02-17089
Figure A-4.
A-8
EIA-530-A to V.35 Adapter and Adapter Cable Pinouts
April 2002
4821-A2-GN20-00
A. Connectors, Cables, and Pin Assignments
Table A-6.
V.35 Cable Interface
ITU-T
Number
Signal
Shield
Pin
—
—
A
Signal Common
102
—
B
Transmitted Data
103
To DSU/CSU
P (A)
S (B)
Received Data
104
From DSU/CSU
R (A)
T (B)
Request to Send
105
To DSU/CSU
C
Clear to Send
106
From DSU/CSU
D
Data Channel Received Line Signal Detector
109
From DSU/CSU
F
Data Set Ready
107
From DSU/CSU
E
108/1, /2
To DSU/CSU
H
Transmit Signal Element Timing (DTE Source)
113
To DSU/CSU
U (A)
W (B)
Transmit Signal Element Timing (DCE Source)
114
From DSU/CSU
Y (A)
AA (B)
Receiver Signal Element Timing (DCE Source)
115
From DSU/CSU
V (A)
X (B)
Local Loopback
141
To DSU/CSU
L
Loopback/Maintenance
140
To DSU/CSU
N
Test Indicator
142
From DSU/CSU
Data Terminal Ready
4821-A2-GN20-00
Direction
April 2002
NN
A-9
A. Connectors, Cables, and Pin Assignments
Alarm Port
The alarm relay reports major alarms through the ALARM port on the faceplate of
the 4800 or 4804 Management Module. The ALARM port is an 8-pin modular
connector; only Pins 2, 3, and 4 may be used.
Maximum ratings for the ALARM connector are:
„
„
„
30 VAC
60 VDC
0.5 A
Table A-7.
Alarm Connector Pinouts
Signal
Pin
None
1
Closed on Alarm (Normally Open) 2
Common
3
Open on Alarm (Normally Closed) 4
A-10
None
5
Future Use
6
Future Use
7
None
8
April 2002
4821-A2-GN20-00
A. Connectors, Cables, and Pin Assignments
Modem Port Connector
The MODEM port connector is a DB9 female connector on the faceplate of the
4800 or 4804 Management Module. It supports an EIA-232 circuit as shown in
Table A-8, Modem Port Connector.
Table A-8.
Modem Port Connector
Signal
Direction Pin Number
—
—
1
Receive Data
In
2
Transmit Data
Out
3
DCE Data Terminal Ready
Out
4
Ground
—
5
Data Set Ready
In
6
—
—
7
—
—
8
—
—
9
Console Port Connector
The CONSOLE port connector is a DB9 male connector on the faceplate of the
4800 or 4804 Management Module. It supports an EIA-232 circuit as shown in
Table A-9, Console Port Connector.
Table A-9.
4821-A2-GN20-00
Console Port Connector
Signal
Direction
—
—
1
Transmit Data
Out
2
ReceiveData
In
3
—
—
4
Ground
—
5
—
—
6
—
—
7
—
—
8
—
—
9
April 2002
Pin Number
A-11
A. Connectors, Cables, and Pin Assignments
A-12
April 2002
4821-A2-GN20-00
Equipment List
B
Table B-1.
Equipment List (1 of 2)
Description
Model Number
Allied Data ADSL Modem – 10BaseT Ethernet and USB port
CJ810
BitStorm 4800 (48-Port)
4821-A1-440
Includes BitStorm 4800, mounting brackets and hardware, and
Installation Guide.
BitStorm 4800 (48-Port, with Management Module and V.35/X.21
Uplink)
4821-A1-441
Includes BitStorm 4800 with Model 4804-B1-000 Management
Module installed, EIA-530-A to V.35 Adapter, mounting brackets and
hardware, and Installation Guide.
BitStorm 4800 (48-Port, with Management Module)
4821-A1-442
Includes BitStorm 4800 with Model 4800-B1-000 Management
Module installed, mounting brackets and hardware, and Installation
Guide.
BitStorm 4800 User’s Guide (paper copy)
4800-A2-GB20
BitStorm 6051 POTS Splitter
6051-B1-001
EIA-530-A to V.35 Adapter
4800-F1-500
EIA-530-A to V.35 Adapter Cable
4800-F1-501
EIA-530-A to X.21 Adapter
4800-F1-502
EIA-530-A to X.21 Adapter Cable
4800-F1-503
Hospitality VBN Server
01-00159-01
In-Line Phone Filter for ADSL
Z-200SM
LEA POTS Splitter Card, 24-port, 600 ohm – Europe
PCO600P24-02
LEA POTS Splitter Card, 24-port, 900 ohm – U.S.
PCO900P24-02
LEA Splitter Chassis, 2-slot, 48-port capacity
RK0215U235
Management Module with V.35/X.21 Uplink
4804-B1-000
Includes EIA-530-A to V.35 Adapter, Installation Instructions.
4821-A2-GN20-00
April 2002
B-1
B. Equipment List
Table B-1.
Equipment List (2 of 2)
Description
Model Number
Management Module
4800-B1-000
Includes Installation Instructions.
B-2
Mounting Brackets for ETSI 535 mm (21″) Rack
4800-F1-011
Splitter Block for ADSL
KHZ-023-6625FF
Subscriber Gateway Server
901-1011-001
April 2002
4821-A2-GN20-00
Technical Specifications
C
Technical specifications are subject to change without notice.
Table C-1. Technical Specifications (1 of 2)
Specifications
Criteria
Cooling and Air
Handling
Each BitStorm 4800 is independently cooled with integral fans and
does not rely on vertical air flow.
Electrical Safety
All interfaces are Safety Extra-Low Voltage (SELV) circuits except:
„
„
DSL ports
Power supply
These are designed in accordance with IEC 60950.
Electromagnetic
Compatibility
(EMC)
Network
Approvals
DSL
Compatibility
Installation
Options
Meets the following standards:
„
„
„
„
„
„
„
EN 50082-1
EN 55022
FCC Part 15, Class A
VCCI Class A
FCC Part 68
Industry Canada CS-03
The BitStorm 4800 supports:
„
„
„
G.dmt (G.992.1)
G.lite (G.992.2)
ANSI T1.413-1998
The Bitstorm 4800 can be:
„
„
„
4821-A2-GN20-00
CISPR 22, Class A
Installed on a desktop and stacked up to eight units high
Mounted with the included mounting brackets in a standard 483 mm
(19″ ) or 584 mm (23″) rack, or, with separately purchased mounting
brackets, in a 535 mm (21″) or 610 mm (24″) rack
Attached vertically to a wall
April 2002
C-1
C. Technical Specifications
Table C-1. Technical Specifications (2 of 2)
Specifications
Criteria
Interfaces
BitStorm 4800:
„
„
DSL PORTS (2): 50-pin RJ21X Telco-type connector
DOWNLINK GigE:
– 8-pin modular jack (10/100/1000BaseT)
– Small Form-factor Pluggable (SFP) socket (1000BaseX)
„
UPLINK GigE:
– 8-pin modular jack (10/100/1000BaseT)
– Small Form-factor Pluggable (SFP) socket (1000BaseX)
„
MGMT: 8-pin modular jack (10/100BaseT)
4800 and 4804 Management Modules:
„
„
„
CONSOLE: DB9 socket, EIA-232
MODEM: DB9 plug, EIA-232
ALARM: 8-pin modular jack
4804 Management Module:
„
V.35/X.21: DB25 socket, EIA-530-A
Operating
Environment
Ambient Temperature: 0° to 50° C (32° to 122° F)
Relative Humidity: 5% to 95% noncondensing
Storage Temperature: –40° to 70° C (–40° to 158° F)
Shock and vibration tolerance sufficient to withstand normal shipping
Physical
Dimensions
Height:
Width:
Depth:
Weight:
Power
90 to 264 VAC at 47 to 63 Hz
Power
Consumption
100 VAC, 1.0A: 95W maximum
44.0 mm (1.72″, or 1U as defined in EIA-310-C) without feet
440.0 mm (17.32″) without mounting brackets
409.7 mm (16.13″)
3.85 kg (8.5 lb)
120 VAC, 0.8A: 95W maximum
240 VAC, 0.5A: 95W maximum
C-2
April 2002
4821-A2-GN20-00
Index
A
D
adapter
EIA-530-A to V.35, A-8
EIA-530-A to X.21, A-6
installing, 2-7
administrator
login, 4-3
mode, 4-3
ALARM port
cabling, 2-12
description, 1-2
pin assignments, A-10
audience for this document, iii
data rate, configuring, 4-5
default
gateway, 4-4
password, 4-3
desktop installation, 1-12
dimensions, C-2
document purpose, iii
documents
related, iii
downlink and uplink pin assignments, A-3
DOWNLINK GigE ports
cabling, 2-4
description, 1-2
pin assignments, A-3
DSL PORTS
cabling, 2-2
description, 1-2
pin assignments, A-4
B
brackets
installation for rack mount, 1-7
C
cables, A-1
DOWNLINK GigE, A-3
DSL PORTS, A-4
EIA-530-A to V.35 adapter, A-8
EIA-530-A to X.21 adapter, A-6
MGMT port, A-2
required, 1-2
UPLINK GigE, A-3
V.35/X.21 port, A-5
CO alarm system, 2-12
CO ground lug, 2-13
Command Line Interface (CLI)
help command, 4-2
using, 4-2
configuration, 4-1
mounting brackets, 1-5
connectors, A-1
front panel, A-1
CONSOLE port
cabling and settings, 2-10
description, 1-2
pin assignments, A-11
cooling and air handling, C-1
CSU cabling, 2-7
4821-A2-GN20-00
E
earth ground, 2-13
EIA-530-A
to V.35 interface, A-8
to X.21 interface, A-6
electrical safety, C-1
Electromagnetic Compatibility (EMC), C-1
Enter key, 4-1
environment, C-2
equipment list
package contents, 1-3
part numbers, B-1
Ethernet ports
pin assignments, A-3
F
fasteners provided, 1-4
feature numbers, B-1
feet, 1-12
fiber optic cable
installing, 2-4
front panel (illustration), A-1
front panel LEDs, 3-3
April 2002
IN-1
Index
G
O
gateway, 4-4
glossary URL, iii
grounding lug, 2-13
operating environment, C-2
optional mounting brackets, 1-5
order numbers, B-1
overview
configuration, 4-1
of book, iii
H
hardware kit contents, 1-4
I
installation options, 1-1
installing
feet for shelf installation, 1-12
in rack, 1-8
Management Module, 1-13
mounting brackets for rack mount, 1-7
mounting brackets for wall mount, 1-10
on shelf or desktop, 1-12
screws for wall mount, 1-11
self-retaining nuts, 1-8
unit into rack, 1-8
unit on wall, 1-10
interfaces, C-2
IP address
Management Module, 4-4
L
LC uplink and downlink, A-3
LEDs, 3-1
descriptions, 3-3
system, 3-1
login, 4-3
lug for grounding, 2-13
M
Management Module
installation, 1-13
setting IP address, 4-4
MGMT port
description, 1-2
pin assignments, A-2
MODEM port
cabling, 2-11
description, 1-2
pin assignments, A-11
mounting brackets
description, 1-6
positioning, 1-6
mounting configurations, 1-5
IN-2
P
package contents, 1-3
part numbers, B-1
password, 4-3
PC cabling and settings, 2-10
physical dimensions, C-2
pin assignments, A-1
power, C-2
connecting cord, 2-14
consumption, C-2
requirements, C-2
switch, 2-14
preinstallation, 1-1
preparation, 1-1
product-related documents, iv
purpose of this document, iii
R
rack installation, 1-8
bracket installation, 1-7
example, 1-9
procedure, 1-8
rate, configuring, 4-5
rear panel (illustration), A-1
related documents, iv
related specifications, iii
requirements, 1-1
Return key, 4-1
router cabling, 2-7
S
save command, 4-4
screws provided, 1-4
serial interface
configuring type and rate, 4-5
SFP transceiver
installing, 2-4–2-5
requirements, 1-1
shelf installation, 1-12
shipping carton, 1-3
site
preparation, 1-1
requirements, 1-1, C-2
April 2002
4821-A2-GN20-00
Index
specifications
related, iii
subnet mask, 4-4
synopsis of chapters, iii
system LEDs, 3-1
T
technical specifications, C-1
Telco connectors
fastening, 2-2
terminal cabling and settings, 2-10
transceive requirements, 1-1
troubleshooting
LEDs, 3-1, 3-3
typographic conventions, 4-1
U
unpacking, 1-3
uplink
configuring interface type, 4-5
options, 2-5
uplink and downlink pin assignments, A-3
UPLINK GigE ports
cabling, 2-5
description, 1-2
pin assignments, A-3
4821-A2-GN20-00
V
V.35 adapter
installing, 2-7
V.35/X.21 port
cabling, 2-7
configuring interface type and rate, 4-5
description, 1-2
pin assignments, A-5
V.35 adapter, A-8
X.21 adapter, A-6
VT100 cabling and settings, 2-10
W
wall mount
bracket installation, 1-10
screw positions, 1-11
weight, C-2
X
X.21 adapter
installing, 2-7
April 2002
IN-3
Index
IN-4
April 2002
4821-A2-GN20-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising