Teryx 750 (2008) Coil Kit

Teryx 750 (2008) Coil Kit
Dynatek Coil Kit DCK2-4
Kawasaki Teryx 750 UTV 2008 (Carbureted models)
Congratulations on your purchase of a Dynatek Ignition Coil Kit. Please take a moment to read these instructions
completely before installing the ignition coils. The installation will take about 1 hour.
WARNING: This kit is for carbureted models only. Do not use on fuel injected models or damage to the injection
computer may result. Injected models require kit number DCK2-6 supplied with 3 ohm coils .
This kit includes: (2) Dynatek 0.5 Ohm (one-half ohm)Mini-Coil
(2) Spark plug wires, 16” and 48”
(1) Wire harness adaptor (front cylinder primary)
(1) Wire harness extension (rear cylinder primary)
(2) M6 x 80 long bolts
(2) M6 locking nuts
(4) Flat washers
(4) Mounting Spacers
Note: The stock sparkplug boots will be reused in this application.
Note: Route all wires carefully. Secure wires in factory loops or use cable ties to ensure electrical wires do not chafe or
touch anything hot. Pay close attention to the wiring detail and wire crimping, successful installation depends on this.
Tools Required:
8mm, 10mm socket wrench
1/4” Flat blades, #3 Phillips screw drivers
Center punch, Drill, and .25” drill bit (1/4”)
Installation
1)
Remove seats, air filter cover, engine cover, drive shaft cover, and front engine cover. Do this by removing a lot
of push pins. Push pin center can be lifted out using two 1/4” flat blade screw drivers on either side of the push
pin. Use #3 Phillips to remove 3 screws holding cover over shifter.
2)
The front cylinder coil is located under the driver seat. The rear cylinder coil is located under the passenger seat.
3)
Disconnect the two primary wires from each coil. Unplug the spark plug caps. Remove the mounting screws
and the coils. Hold the stock sparkplug wire near the cap and unscrew the cap counterclockwise. This cap will
be used with the Dyna coils.
4)
Both Dyna coils will be fastened to the sheet metal below the driver seat. Center the Dyna coils, right to left,
below the factory coil tab. This requires two 1/4” holes. Find the metal piece that is 1.5“ tall. It is 1/8” thick
and extends about 8 inches right to left under the driver seat. Mark the hole centers 0.75” up the metal, and
3.25” apart. Then drill thru using .25” bit. (see picture, Step 4) (Use drill template)
5)
Mount a Dyna coil on each side of the metal, so that spark plug towers point toward engine. The aluminum
spacers go between both coils and the sheet metal. Fasten using long M6 bolts with flat washers under the heads
and nuts. Tighten all bolts securely so Dyna coils are not loose (see pictures, Step 5, 6)
6)
Attach primary wires to the Dyna coils. The coil in front of the metal is for the front cylinder. Green/White wire
to terminal without a dot. Black/Yellow wire goes to Orange adapter wire then to terminal with a RED dot. Use
a razor knife to trim the electrical tape and wire sleeve of the factory harness back a few inches. This will relieve
wire strain from the Orange wire. The coil behind the metal is for the rear cylinder. Use the wire harness
extension. Blue/White wire to terminal without a dot. Black/Yellow wire to terminal with a RED dot. Connect
other end of harness extension to same colors of factory harness. (see pictures, Step 6)
7)
Attach the short spark plug wires to the front coil. Route wire thru frame loop and to front spark plug. Trim
length if required. Screw factory cap clockwise onto new wire until bottomed. Then press cap onto spark plug.
Attach the long spark plug wire to the rear coil. Route wire with others thru frame, 90 degree V, and thru factory
loops to rear spark plug. Trim wire length if required. Screw factory cap clockwise onto new wire until
bottomed. Then press cap onto spark plug. (see pictures, Step 7)
8)
Check that all wires are routed and held securely. Use zip-ties. Use the flexible factory cable and hose
restraints. (see pictures, Step 8)
9)
Replace engine covers, and seat.
10)
Start the engine. Installation is complete!
DYNATEK 164 S. Valencia St., Glendora, CA 91741 800-928-3962 www.dynaonline.com
2801376C
Step 4: Drill 2 holes. (0.25 inch dia.)
Step 5: Mount Dyna coils.
Step 6: Attach coil primary wires.
Step 7: Wire routing. (Front Cylinder)
Step 7: Wire routing. (Rear Cylinder)
Step 8: Wire routing. (Rear Cylinder)
DYNATEK 164 S. Valencia St., Glendora, CA 91741 800-928-3962 www.dynaonline.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising