286 3 en~v~Specification Sheet

286 3 en~v~Specification Sheet
HEAT RECOVERY VENTILATOR
Venmar AVS E10 HRV
Part no. 41126
50 to 105 CFM (0.4 in. w.g.)
Controls
• This unit is very simple to operate. Once it is installed, press on its
push button, located under the unit, to activate it. Press once for low
speed, once again for high speed, and once more to stop it.
• For more convenience, this unit can also be controlled by an optional
main control. For a complete list of optional main and auxiliary
controls available, refer to the Wall Control Compatibility Chart
on last pages of wall controls specification sheet, available at
www.venmar.ca.
• For more details about controls, refer to the Main and auxiliary wall
controls user guide, also available at www.venmar.ca.
Options
• Complete line of registers and diffusers
• Electric duct heater
VB0212
THE LATEST ADDITION TO OUR NEW E SERIES
This new model is designed to provide a superior heat recovery,
meeting the highest requirements of energy-efficient home
programs. By getting more points from it’s category in the builder option
packages*, it represents a cost-effective solution for efficent home
contractors.
The E10 HRV offers all the basic features for the new
construction market, such as integrated balancing dampers
and a defrosting system without negative pressure. Moreover, all aspects
of its design were thought to ease balancing of air flow and simplify
installation; it also offers easy access to electronic components.
This unit does not only improve the indoor air quality, it also lowers the
customer’s energy bills while bringing added value to the contractor.
*Applies to certain energy-efficient building programs.
• Features pressure taps, balancing dampers and port straps to
simplify installation
• Easy to access electronic module
• Homeshield™ defrosting system (no negative pressure)
• Heat recovery core offers greater comfort
• Designed with 2 PSC high-pressure blowers
• Integrated draining system
• ENERGY STAR® qualified
REPAIRS AND MAINTENANCE
The E10 HRV’s low power consumption PSC motors are
permanently lubricated. The electronic circuit board eliminates
electromechanical parts, reducing repair time to a minimum.
WARRANTY
The E10 HRV is protected by a 5-year warranty on parts only,
except for the heat recovery core, which is covered by a limited lifetime
warranty, with the original proof of purchase.
Available at:
Homeshield™ Defrosting System
The E10 HRV uses a unique defrosting method. No negative
pressure is created by air exhausted to the outdoors, as the air is
recirculated into the house, helping to prevent any backdraft.
STALE AIR
FILTERED AIR
FROM BUILDING
TO BUILDING
OUTSIDE TEMPERATURE DEFROST CYCLE MIN./
°C
°F
OPERATING MIN.
WARMER
WARMER
NO DEFROST
THAN -5
THAN 23
-5 TO -15 23 TO 5
5/40
-15 TO -27 5 TO -17
5/25
- 27
-17
8/22
AND LESS
AND LESS
VF0046
Heat Recovery Core
Dimensions: 10” x 10” x 14.25” (25.4 cm x 25.4 cm x 36.2 cm)
Exchange surface: 100 ft.2 (9.3 m2)
Weight: 7.26 lb. (3.3 kg)
Material: Polypropylene
Type: Cross flow
Warranty: Limited lifetime
Requirements and standards
• Complies with the UL 1812 requirements regulating the installation
of Heat Recovery Ventilators
• Complies with the CSA C22.2 no. 113 Standard applicable to ventilators
• Complies with CSA C444 requirements regulating the installation of
Heat Recovery Ventilators
• Technical data was obtained from published results of tests relating
to CSA C439 Standards
• HVI certified and ENERGY STAR® qualified
DIMENSIONS: E10 HRV
23 9/16”
(599 mm)
2 ¹/16”
(53 mm)
3 13/16”
(97 mm)
24 9/16”
(624 mm)
1
3 FT.
22 ½”
(572 mm)
3
7 7/16”
(189 mm)
POWER CORD
2
NOTE: Every port fits 6” round duct.
18 ¼”
(464 mm)
14 1/16”
(358 mm)
4
14 15/16”
(380 mm)
VK0066A
1:
2:
3:
4:
EXHAUST AIR TO OUTSIDE PORT
FRESH AIR FROM OUTSIDE PORT
EXHAUST AIR FROM BUILDING PORT
FRESH AIR TO BUILDING PORT
NOTE: ALL UNITS PORTS WERE CREATED TO BE CONNECTED TO DUCTS HAVING A MINIMUM OF 6” DIAMETER, BUT IF NEED BE, THEY CAN BE CONNECTED TO BIGGER SIZED DUCTS BY
USING AN APPROPRIATE TRANSITION (E.G.: 6” DIAMETER TO 7” DIAMETER TRANSITION).
EXTERNAL
STATIC PRESSURE
PA
IN. W.G.
25
0.1
50
0.2
75
0.3
100
0.4
125
0.5
150
0.6
175
0.7
200
0.8
NET SUPPLY
AIR FLOW
SUPPLY
L/S
CFM
M3/H
L/S
CFM
74
66
58
50
42
35
28
20
157
139
122
105
90
74
59
43
267
236
207
178
153
126
100
73
75
66
58
50
42
35
28
21
158
140
122
106
90
75
59
44
GROSS AIR FLOW
EXHAUST
M3/H
L/S
CFM
268 77 164
238 70 148
207 63 132
180 55 117
153 49 104
127 42
90
100 37
78
75
31
66
M3/H
279
251
224
199
177
153
133
112
ENERGY PERFORMANCE
SUPPLY
TEMPERATURE
°C
°F
HEATING
0
32
0
32
0
32
-25 -13
NET AIR FLOW
POWER
SENSIBLE
APPARENT
LATENT RECOVERY/
CONSUMED
RECOVERY
SENSIBLE
MOISTURE
L/S
CFM
M3/H
WATTS
EFFICIENCY
EFFECTIVENESS
TRANSFER
24
31
40
30
50
65
84
64
85
110
143
109
42
54
66
72
75
75
73
70
84
83
80
84
0
0
0
0.05
EXTERNAL STATIC PRESSURE (IN. W.G.)
VENTILATION PERFORMANCE
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
VG0095A
SUPPLY
EXHAUST
0 15 30 45 60 75 90 105 120 135 150 165 180
GROSS AIR FLOW (CFM)
NOTE: All specifications are subject to change without notice.
SPECIFICATIONS
• Model: AVS E10 HRV
• Part Number: 41126
• Total Assembled Weight (including
polypropylene core): 52 lb. (23.6 kg)
• Oval shaped ports; fit 6” round ducts
• Drain: 1/2” (1.2 cm) integrated fittings with
10 ft. (3 m) PVC drain hose
• Core Filters: 2 washable Merv 7 filters,
9.2” x 14.25” x 0.38”
(23.4 cm x 36.2 cm x 1 cm)
Project:
Location:
Part no.: 41126
Qty.:
Submitted by:
•
•
•
•
Housing: Pre-painted steel
• Speed Control on Unit:
Insulation: Expanded polystyrene
- Low speed and high speed
Mounting: Suspension by chains and springs - Other modes available with Altitude,
Supply and Exhaust Blower Motors:
Deco-Touch or Lite-Touch Constructo
2 PSC motors
main controls
- Protection type: Thermally protected
- Insulation class: F
• Heat Recovery Core:
• Unit Electrical Characteristics:
- Heat Exchange Surface Area: 100 ft.2 (9.3 m2)
Volts Frequency Ampere Watts
- Type/Material: Crossflow/Polypropylene
120
60 Hz
0.9
84
REMARKS
Date:
Residential Products Group, 550 Lemire Blvd., Drummondville, Qc, Canada J2C 7W9 - Tel.: 1-800-567-3855 Fax: 1-800-567-1715
www.venmar.ca
AVSE10HRVd151014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement