#602 EPOXY SURFACE SEALER

#602 EPOXY SURFACE SEALER
T
E
C
H N I
C
A
L
D
A
T
A
#602 EPOXY SURFACE SEALER
CAUTION
DESCRIPTION
#602 is a 100% solids, non sag epoxy paste used
primarily for sealing cracks prior to injection with
#1001 injection epoxy or #900 polyurethane resin.
This FAST SETTING paste enables the user to inject within 30 minutes.
Manufacturer
CPR Products, Inc.
1315 West Lark Ind. Park.
St. Louis, MO 63026
Telephone: [636] 717-0666
Fax
[636] 717-0665
Toll Free:
[888] 531-8940
THIS MATERIAL IS INTENDED FOR INTERIOR
USE OR EXTERIOR APPLICATIONS WHERE SURFACE SEALER WILL BE
REMOVED AFTER INJECTION RESIN HAS CURED.
PROPERTIES OF #602 EPOXY SURFACE SEALER
Mix Ratio
Pot Life
Injectable Cure Time
Cure Time
1:1 by volume
5-8 minutes
30 minutes
24 hours
@77°F
Benefits
•
•
•
•
•
Easy 1:1 mix ratio
No shrinkage
Excellent adhesion to concrete, wood and metals
Smooth consistency, easy
to feather edge
Non sag
Cured Properties
Compressive Strength
Tensile Strength
Tensile Elongation
Slant Shear Strength
Shore D Hardness
7,920 psi
3,280 psi
.2%
100% concrete failure
85 – 90
How to use
Surface Preparation:
Before application of compound, surface must be clean
and sound. Remove all dirt,
laitance, grease, curing compounds and other foreign matter. Roughen surface with
wire brush or wire wheel.
Mixing:
Blend one Part A with one
Part B by volume until uniform
gray color [no streaks]. Incorrect mix ratio will prevent
proper cure. Do not mix more
than can be used within 5-8
minutes.
Application:
Setting surface mount ports
Prepare a small batch of #602
for use as an adhesive for setting ports. Apply a thin bead of
material around the perimeter of
the ports’ base.
CPR PRODUCTS, INC.
Distributed by: BEST MATERIALS ® LLC
Ph: 800-474-7570, 602-272-8128 Fax: 602-272-8014
www.BestMaterials.com Email: Sales@BestMaterials.com
Application continued:
Center barrel of port over
crack and press into place.
Be careful not to plug the
opening in the bottom of the
port.
Sealing crack
Mix additional surface seal
material as previously described, then, using a putty
knife or margin trowel seal off
the crack and around the
base of each port. Use forceful strokes of the putty knife
or margin trowel while sealing
in order to insure proper bond
to roughened concrete surface. Apply approximately
1/8” thick layer of material by
3” wide over the center of the
crack
Limitations/ Precautions
Temperature of substrate
must be above 40°F. New
concrete must be at least 28
days old. Alteration of #602
with solvents for thinning purposes will prevent proper
cure.
Danger! Causes severe eye
and skin burns. May cause
blindness. Harmful if swallowed. May cause allergic
reaction. Do not get into
eyes, skin or clothing. Use
safety glasses and wear protective rubber gloves. Avoid
breathing vapor or mist. Keep
container closed. Use only in
well ventilated areas. In case
of contact, wash immediately
with soap and water. Keep
away form all food and food
containers.
Cleaning
All tools and equipment
should be cleaned before the
system gels. Use M. E. K. Or
safety solvent when necessary.
Packaging
• 22 oz. Dual Cartridges
packed 12 sets per case
Storage
#602 should be stored in a
dry environment between 6080°F.
Technical Service
Complete technical service
and specification services are
available from the manufacturer and their authorized representatives.
Warranty
All recommendations, statements and technical data contained herein are based on
tests we believe to be reliable
and correct. CPR Products,
Inc. warrants its products to
be free of manufacturing defects and that at the time and/
or place of shipment our material will meet current published physical properties
when applied with ASTM and
CPR Products, Inc. standards. CPR Products, Inc.
liability is limited to the replacement of the material if
found to be defective. As
CPR Products, Inc. has no
control of the use to which
others may put its products, it
is recommended the products
be tested to determine if suitable for specific application
and/or our information is valid
in a particular circumstance.
Responsibility remains with
the architect, engineer, contractor and the owner for the
design, application and proper
installation of each product.
Nothing contained herein
shall be construed to be a
recommendation to use or as
a license to operate under or
to infringe any existing patentents.
CPR PRODUCTS, INC.
Distributed by: BEST MATERIALS ® LLC
Ph: 800-474-7570, 602-272-8128 Fax: 602-272-8014
www.BestMaterials.com Email: Sales@BestMaterials.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising