RW32.1 Bullet Style Inwall IR Receiver

RW32.1 Bullet Style Inwall IR Receiver
RW32.1
P
R
O
D
Bullet Style In-Wall IR Receiver
PDP/LCD Friendly and CFL Proof
U
C
T
I
N
F
O
R
M
A
T
I
O
N
A
Overview
RW32.1 IR receiver is ideal for mounting in racks, cabinets, panels, walls, etc for control of A/V
devices behind closed doors and/or mounting on the baffles of In-wall/In-ceiling speakers, anywhere where a stealth look is highly desirable. A white bezel is supplied on the unit as well as an
extra black bezel for select installations.
N
D
I
N
S
T
A
L
L
A
T
I
O
N
G
U
I
Installation Diagram
DC12V
A/V RECEIVER
VOLUME
TUNE
SEARCH
FM
CENTER
STEREO TUNE
TUNE
MODE
STORE
PRESET
PHONES
Product Specifications & Features
EXTRA
SPEAKERS
BASS
BALANCE
TAPE 1
MONITOR
VIDEO
TAPE 2
VCR
LD
AUX
CD
AM
MONO
FM
+12V
GND
ST OUT
1. Infrared Frequency Bandwidth: 38KHz (± 2KHz); operates with most remotes.
2. Reception Distance On-Axis: Up to 50 feet indoor, 15 to 20 feet in direct sunlight. Range
depends on device being controlled and levels of IR and EMI interference.
3. Reception Off-Axis: Up to a distance of 20 feet at ±45 degrees.
4. Visible Blinking-Talk Back LED: Red LED indicator confirms receipt of IR codes.
5. Measurements: 12mm (diameter) x 48.5mm (mounting depth)
6. Power requirement: 12VDC/500mA or higher Power Adaptor.
7. Infrared receiver with 6.5 foot/2.0M length of 3/C ribbon cable; acts as a remote receiver
& control unit.
TREBLE
CD PLAYER
IR IN
Compact Disc Player
MIN
SEC
PLAY PAUSE
STOP
RANDOM
SKIP
OPEN
TIME
REPEAT
SCAN
6 7 8
9 10
DVD PLAYER
DVD PLAYER
Product Installation
1. Drill a 12mm hole in the selected mounting surface to insert the RW33.1 through; pay
attention to any hidden wires, etc behind the drilling area. Once the RW32.1 is installed
through the hole, tighten up the nut supplied on to the threaded body of the RW32.1.
2. Run a length of cable between the RW32.1’s 3/C ribbon cable to the screw terminals of
the C21, C41 or C61 connecting block. Remove about 1/4” of insulation from both ends of
all wires and twist the exposed strands together for termination to these products. Notes: “
V+” - 12V DC Power, “ G ” – Ground and “IR ” - IR signal.
3. It is not recommended to connect without a connecting block or directly to a power adaptor
or battery. Be sure the green LED illuminates on the C21, C41 or C61 when plugging in the
power adaptor.
4. The RS32.1 is PDP/LCD Friendly and CFL Proof; this IR Receiver can be installed within
inches of either a PDP/LCD or in Direct Sunlight and operate effectively! The RS32.1’s may
be connected in parallel sequentially.
RW32.1
V+: BLACK WITH
GREY SOLID STRIPE
G: BLACK
BACK VIEW FOR
CODING & DEFINITION
REMOTE CONTROL
IR: BLACK WITH GREY
DASHED STRIPE
In North America contact:
Trends Electronics International Inc. - 100 – 980 West 1st Street. North Vancouver, B.C. V7P 3N4
Phone: 1 (877) 946-9255 Fax: 1 (800) 618-7363 Email: orders@trendsinc.com
D
E
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising