TYPE APPROVAL CERTIFICATE This is to certify:

TYPE APPROVAL CERTIFICATE This is to certify:
TYPE APPROVAL CERTIFICATE
Certificate No:
A-14149
File No:
899.30
Job Id:
262.1-016903-2
This is to certify:
That the Personal Computer
with type designation(s)
enix-2067/3067, enix-2077/3077, enix-2087/3087 and enix-4100/41x9
Issued to
Elektronix Com-Scan AS
Lysaker, Norway
is found to comply with
Det Norske Veritas' Rules for Classification of Ships, High Speed & Light Craft and Det Norske
Veritas' Offshore Standards
IEC 60945 Ed. 4 (2002-08) Maritime navigation and radiocommunication equipment and
systems - General requirements - Methods of testing and required test results
Application :
Location classes:
Temperature
Humidity
Vibration
EMC
Enclosure
B*
B
A
B
Required protection according to DNV Rules
shall be provided upon installation on board
*Tested at -15°C
This Certificate is valid until 2018-06-30.
Issued at Høvik on 2015-02-02
DNV GL local station: Oslo Maritime and CAP
for DNV GL
Digitally Signed By: Sneen, Ståle
Location: DNV GL Høvik, Norway
Approval Engineer: Nils Jarem
Signing Date: 2015-02-04, on behalf of
Odd Magne Nesvåg
Head of Section
This Certificate is subject to terms and conditions overleaf. Any significant change in design or construction may render this Certificate invalid.
The validity date relates to the Type Approval Certificate and not to the approval of equipment/systems installed.
Form code: TA 1411a
Revision: 2014-11
© DNV GL 2014. DNV GL and the Horizon Graphic are trademarks of DNV GL AS.
www.dnvgl.com
Page 1 of 3
Certificate No: A-14149
File No:
899.30
Job Id:
262.1-016903-2
Product description
Enix 2067/3067 & 2077/3077
Rating: 24V DC
Compass safe distance :
Standard compass:
Steering compass:
Enix-2087
Rating: 24V DC
Compass safe distance :
45 cm
25 cm
Standard compass:
Steering compass:
240 cm
150 cm
Standard compass:
Steering compass:
170 cm
115 cm
Enix 4100/41x9
Rating: 100-240V AC 50/60Hz
Compass safe distance :
Standard compass:
Steering compass:
200 cm
140 cm
Enix-3087
Rating: 24V DC
Compass safe distance :
Approval conditions
The Type Approval covers hardware listed under Product description. When the hardware is used in
applications to be classed by DNV, documentation for the actual application is to be submitted for
approval by the manufacturer of the application system in each case. Reference is made to DNV Rules
for Ships Pt.4 Ch.9 Control and Monitoring Systems.
Product certificate
If specified in the Rules, ref. Pt.4 Ch.9 Sec.1, the control and monitoring system in which the above
listed hardware is used shall be delivered with a product certificate. For each such delivery the
certification test is to be performed at the manufacturer of the application system before the system is
shipped to the yard. The test shall be done according to an approved test program. After the certification
the clause for application software control will be put into force.
Clause for application software control
All changes in software are to be recorded as long as the system is in use on board. The records of all
changes are to be forwarded to DNV for evaluation and approval. Major changes in the software are to
be approved before being installed in the computer
Type Approval documentation
Data sheets:
enix 3077, enix 3067, enix 2077, enix 2067, enix-41X9/4100
enix-2087, enix-3087
Manuals:
User manual enix-20xx and enix-30xx version 2.0
User manual enix 41xx series version 2.0
User manual enix-2087and enix-3087 version 1.1
Test reports: E12134.05 revision 05, E13045.00 revision 00
E14165.00 revision 00
DNV GL Oslo initial assessment report, dated 2014-02-07.
Tests carried out
Applicable tests according to Standard for Certification No. 2.4, April 2006,
also covering IACS Unified Requirements E10 Rev.5.
Applicable tests for protected equipment according to IEC 60945, 4th edition (2002) and corrigendum 1.
Form code: TA 1411a
Revision: 2014-11
www.dnvgl.com
Page 2 of 3
Certificate No: A-14149
File No:
899.30
Job Id:
262.1-016903-2
Marking of product
The products to be marked with model name, manufacturer name and serial number.
Periodical assessment
The scope of the periodical assessment is to verify that the conditions stipulated for the type are
complied with, and that no alterations are made to the product design or choice of systems, software
versions, components and/or materials.
The main elements of the assessment are:
·
Ensure that type approved documentation is available
·
Inspection of factory samples, selected at random from the production line (where practicable)
·
Review of production and inspection routines, including test records from product sample tests and
control routines
·
Ensuring that systems, software versions, components and/or materials used comply with type
approved documents and/or referenced system, software, component and material specifications
·
Review of possible changes in design of systems, software versions, components, materials and/or
performance, and make sure that such changes do not affect the type approval given
·
Ensuring traceability between manufacturer’s product type marking and the type approval certificate
Periodical assessment is to be performed at least every second year and at renewal of this certificate.
END OF CERTIFICATE
Form code: TA 1411a
Revision: 2014-11
www.dnvgl.com
Page 3 of 3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising