datasheet for PSF100-24S by Arch Electronics Corp.
VER : A_2
update : 2013.05.16
LED Power
PSF1 0 0 SERI ES
1 0 0 W atts
KEY FEATURES
 Fully Isolated Plastic Case with IP67 Level
 With Constant Current & Constant Voltage (C.C+C.V mode)
 With P.F.C. Function, PF>0.9
 High Efficiency up to 90%
 Free Air Convection
 Protections: Over Load / Over Voltage / Short Circuit
 High Reliability & Double Layered PCB
 Suitable for LED lighting and moving sign applications
 Isolation Class II
 3-Years Product Warranty
ELECTRICAL SPECIFICATIONS
All specifications valid at normal input voltage, full load and +25°C after warm-up time unless otherwise stated.
Model No.
Max output wattage
(W)
Voltage
Input
(Note2)
PSF100-54S
96W
96W
96W
95.58W
90-295 VAC
50 / 60 Hz
PF>0.9 at Full load (115 VAC / 230 VAC)
Current (Full load)
1.4A (115 VAC) / 0.7A (230 VAC)
(at 230 VAC)
60 A max.
Leakage Current
< 0.7 mA max at 240 VAC
Voltage (V.DC.)
24V
36V
48V
54V
22 ~ 26.5V
33 ~ 39.5V
44 ~ 51.5V
49 ~ 55V
Constant Current Operation Voltage (max)
(CC Mode)
(Note3)
15.6~ 24
VDC
23.4~36
VDC
31.2~48
VDC
35.1~54
VDC
Voltage Tolerance
Preset Current (mA)
(CC Mode) (fixed)
Minimum Load (mA)
±10%
3500 (2600~4000)
2100 (1720~2650)
1750 (1300~2000)
1400 (1150~1770)
2600
1720
1300
1150
89%
90%
Line Regulation (typ.)
Isolation
PSF100-48S
Power factor
Voltage ADJ Range Setup
Protection
PSF100-36S
Frequency (Hz)
Inrush current
Output
PSF100-24S
(CV Mode)
(at 230 VAC)
(110-240 VAC)
±4%
Load Regulation (Min-Max) (typ.)
±5%
Ripple & Noise (typ.) (Note1)
2.7Vp-p
5Vp-p
Efficiency (at 230VAC / Full Load)(typ)
89%
90%
Over current protection
Auto recovery
Over voltage protection
Zener diode clamp
Short circuit protection
Auto recovery
Input-Output (V.AC)
3750V
Operating temperature
-30°C…+70°C (with derating)
Storage temperature
-40°C…+85°C
Temperature coefficient
0.02%/°C
Humidity
95% RH
MTBF
>450,000 h @ 25°C (MIL-HDBK-217F)
Dimension (L x W x H)
5.67 x 2.76 x 1.48 Inches
Weight
640 g
Cooling method
Free air convection
Safety
Agency Approvals
UL8750
EMC
EMI
(Conducted & Radiated Emission)
EMS (Noise Immunity)
EN 6154
Harmonic Current
EN 61000-3-2(at Full Load) EN 61000-3-3
Surge
2KV L-N
Environment
Physical
http://www.archcorp.com.tw
TEL: +886-2-26989508 FAX: +886-2-26981319
( 144.0 x 70.0 x 37.5 mm ) Tolerance 2mm
IEC / EN 61347-2-13
IEC / EN 61347-1
EN 55015
-1-
VER : A_2
update : 2013.05.16
LED Power
PSF1 0 0 SERI ES
1 0 0 W atts
Note:
1. Ripple & Noise are measured at 20MHz of bandwidth with 0.1uF & 47uF parallel capacitor.
2. Please check the derating curve for more details.
3. Input Voltage=115 or 230 VAC
This is the suitable operation region for LED related application.but please reconfirm special electrical requirements
for some specific system design.
MECHANICAL DIMENSION
( Top View )
DERATING
If the output is not connected LEDs, the input voltage must be greater than 180VAC.
BLOCK DIAGRAM
http://www.archcorp.com.tw
TEL: +886-2-26989508 FAX: +886-2-26981319
-2-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising