Jetta J-10V Sanibel Specifications Sheet

Jetta J-10V Sanibel Specifications Sheet
72" x 42" x 27"
Sanibel
(J-10V)
series
The Sanibel's large and
luxurious bath power with
strategically placed back
massage jets and comfortable
arm rests at each end.
Features:
• 13 flow-adjustable and directional jets including:
• 6-pack back jets
• 2 hand jets
Operating Gallons (approx.):
• 3-pack back jets
• 2 hip jets
• Regular Usage - 45 gal.
• 3 B.H.P. pump - 14.4 Amps
• Upper Body Usage - 75 gal.
• Tri-ssage controls for distinct pump flow rates
• High gloss / high impact acrylic in standard colors
Options Available:
• Totally insulated with polyurethane foam
• Upper body jets can be shut down for operation at a • Mood or LED lights
• Whirly triple spinning jets
lower water level
• Bath waste & overflows
• Silent passive warm air induction system
• Decorator and designer colors
• Drain back technology for sanitary bathing
• Contoured neck support pillow
• 5-year limited factory warranty
• Jetted neck pillow
• Anti-microbial flex piping
• Aromatherapy
• Extra thick glassing
• 6" acrylic grab bars
• Pre-leveled base
• Extra jets
• Slip resistant bottom
• Energy efficient
Colors Available:
• Noise absorbtion
• White • Biscuit • Almond (Standard)
• Sandbar • Mexican Sand
• Black • Ice Gray
Stay Hot Guarantee
Jetta guarantees that after 30 minutes of use, the
water temperature will not drop more than two
degrees. Our fully insulated whirlpool baths with
low density foam insulation and passive warm air
induction systems help keep you warmer, longer.
Trim Kit Finishes Available:
• Polished Brass
• Polished Chrome
• Oil Rubbed Bronze
• Satin Nickel
To Order or for More Information, E-mail whirlpool@earthlink.net or call 800-894-1022
© 2007-05 by JETTA CORPORATION. All rights reserved.
whirlpoolbath.net
Sanibel
72" x 42" x 27"
Jetta Corporation
Technical Specifications
(J-10V)
(R/B)
(L/B)
41411/2
30 1/2 20 1/2
30 1/2 20 1/2
41 1/2
10 3/4
(R/F)
(L/F)
10 3/4
*Stand facing bath to determine pump location.
38 1/2
64 1/2
64 1/2
72
21 1/2
Electrical Specifications:
41 1/2
72
30 1/2 20 1/2
20 1/4
Required Electrical Service 20 1/4110/115 Volts
Standard Whirlpool Bath
20 amp GFI
Entire unit must be protected by a dedicated GFI
breaker (refer to local codes).
Codes/Standards Applicable:
38 1/2
(R/F)
(L/F)
4 1/4
Specified model meets or exceeds the requirements
for the following standards: UL Listed, ANSI, ASME,
IAPMO.
4 1/4
Suggested Pump Access Panel:
20" x 12" - Actual recommended size may vary
depending on distance of access to pump location.
CUT OUT DIMENSION:
27
21 1/2
20 1/4
(L/B)
(L/F)
Subtract 2” from edge. Contact Jetta for template.
Shipping Weight: 270 lbs.
*L/B, R/B, L/F, R/F pump position determines suction location.
Installation: Measure tub before building tub deck. Add 1" to 3" of evenly distributed bedding compound under the
base of the tub to provide maximum support. Tub should not be supported by rim in any way and should be level when installed.
Jetta recommends using a quick setting concrete mix. Plastic sheeting should be laid between bedding and bath during installation.
Drawing shows manufacturer's standard pump location. Optional locations available at an additional cost, depending on feasability.
Contact Jetta for details. Dimensional variance on drawings may be +/- 1/2 inch and are subject to change without notice.
© 2007-05 by JETTA CORPORATION. All rights reserved.
whirlpoolbath.net
4 1/4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising