ComNet™ FVT/FVR107 Optical Video Links

ComNet™ FVT/FVR107 Optical Video Links
FVT/FVR107
Mechanical Installation Instructions
Figure 1: Dimensions are for a standard ComNet™ one slot module.
.156 [3.96 mm]
.313 [7.95 mm]
Installation Considerations
This fiber-optic link is supplied as
a Standalone/Rack module.
Units should be installed in dry
locations protected from extremes
of temperature and humidity.
Standalone Module:
The unit is provided with a mounting plate with holes for two No. 6 pan
head screws (3-mm or 3.55-mm).
Attach the module to a solid piece
of wood using two No. 6 pan head
wood screws with a minimum
penetration into the wood of
3/4 inch. (Screws not supplied)
See figure 1.
1. Determine where the module will
be installed, and ensure that there
is adequate space at both ends
for making the various cable
connections and for reading the
diagnostic LEDs.
2. Attach the module to a flat surface
using two mounting screws.
Rack Module:
The unit is designed to be installed in the ComNet 19-inch (483-mm) EIA standard card-cage rack, the C1-US,
C1-EU, or the C1-CH. Follow these guidelines to install rack cards after performing module setup procedures.
C1-US, C1-EU, or the C1-CH Card Cage Racks
CAUTION: Although the units are hot-swappable and may be installed without turning power off to the rack,
ComNet recommends that the power supply be turned off and that the rack power supply is disconnected
from any power source. Note: Remove electrical connector before installing in card cage rack.
1. Make sure that the card is oriented right side up, and slide it into the card guides in the rack until the
edge connector at the back of the card seats in the corresponding slot in the rack’s connector panel.
Seating may require thumb pressure on the top and bottom of the card’s front panel.
CAUTION: Take care not to press on any of the LEDs.
INS_FVTFVR107_REVA
2. Tighten the two thumb screws on the card until the front
panel of the card is seated against the front of the rack.
07/22/09
Page 1
FVT107
10-BIT DIGITAL VIDEO WITH 1 BI-DIRECTIONAL
DATA CHANNEL/DUAL OPTICAL PORT REDUNDANT
INSTALLATION INSTRUCTIONS
POINT-TO-POINT CONFIGURATION
Communication Networks
+ 8 CONTACT CLOSURES
3 Corporate Drive • Danbury, CT 06810 • USA
Tel: 203-796-5300 • Toll Free: 1-888-678-9427
www.comnet.net
MULTIMODE
OR SINGLE MODE
OPTICAL FIBER
BLACK WITH WHITE STRIPE
BLACK
NOTE: Remove Electrical Connector for
Rack Mount Units
WARNING: Unit is to be used with a Listed Class 2 or LPS power supply rated 9-12 VDC @ 1A.
WARNING: This unit should be installed in a restricted access location; available through the use of a lock and key or other
means of security. Access should be limited to service personnel who have been instructed about the reasons for the restrictions
to the location. Any and all precautions should be taken and controlled by the authority responsible for the location.
IMPORTANT SAFEGUARDS:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly,
the operating ambient temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an environment compatible with
the maximum ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised.
INS_FVTFVR107_REVA
07/22/09
Page 2
FVR107
10-BIT DIGITAL VIDEO WITH 1 BI-DIRECTIONAL DATA
CHANNEL/DUAL OPTICAL PORT REDUNDANT
POINT-TO-POINT CONFIGURATION
Communication Networks
+ 8 CONTACT CLOSURES
3 Corporate Drive • Danbury, CT 06810 • USA
INSTALLATION INSTRUCTIONS
Tel: 203-796-5300 • Toll Free: 1-888-678-9427
www.comnet.net
MULTIMODE
OR SINGLE MODE
OPTICAL FIBER
BLACK WITH WHITE STRIPE
BLACK
NOTE: Remove Electrical Connector for
Rack Mount Units
WARNING: Unit is to be used with a Listed Class 2 or LPS power supply rated 9-12 VDC @ 1A.
WARNING: This unit should be installed in a restricted access location; available through the use of a lock and key or other
means of security. Access should be limited to service personnel who have been instructed about the reasons for the restrictions
to the location. Any and all precautions should be taken and controlled by the authority responsible for the location.
IMPORTANT SAFEGUARDS:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly,
the operating ambient temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an environment compatible with
the maximum ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised.
INS_FVTFVR107_REVA
07/22/09
Page 5
FVT/FVR107
10-BIT DIGITAL VIDEO WITH 1 BI-DIRECTIONAL
DATA CHANNEL/DUAL OPTICAL PORT REDUNDANT
POINT-TO-POINT CONFIGURATION
Communication Networks
+ 8 CONTACT CLOSURES
3 Corporate Drive • Danbury, CT 06810 • USA
INSTALLATION INSTRUCTIONS
Tel: 203-796-5300 • Toll Free: 1-888-678-9427
www.comnet.net
LED INDICATORS
GREEN
RED
OPTIC
VIDEO
POWER
Communication link has
An active video signal is Unit powered up
been established over
present on the BNC
optical fiber
connector.
Communication link has
No video signal
–
not been established.
OFF
Not powered up correctly –
Unit powered down
INS_FVTFVR107_REVA
07/22/09
Page 6
FVTFVR107
10-BIT DIGITAL VIDEO WITH 1 BI-DIRECTIONAL
DATA CHANNEL/DUAL OPTICAL PORT REDUNDANT
POINT-TO-POINT CONFIGURATION
+ 8 CONTACT CLOSURES
SWITCH POSITIONS
FIG. A
RS-232 DATA
1
2
RS-422, BI-PHASE or
MANCHESTER DATA
1
2
SWITCH
RS-485, 2-WIRE
SENSORNET DATA
1
LINK A, LINK B RELAY OUTPUTS:
Terminal pairs are closed when
the corresponding Optical Port
has established LINK.
Terminal pairs are open when
the corresponding Optical Port
has lost LINK.
2
RS-485, 4-WIRE
DATA
1
2
ALARM RELAY OUTPUT,
FVR107 ONLY:
Terminal pair is closed
when BOTH Optical
Ports have established
LINK.
Terminal pair is
open when either
Optical Port has
lost LINK.
INS_FVT107_REVA
07/22/09
Communication Networks
3 Corporate Drive • Danbury, CT 06810 • USA • Tel: 203-796-5300 • Toll Free: 1-888-678-9427 • www.comnet.net
Page 7
FVT107
FVR107
FVT107
DATA
CONNECTIONS
RS-232*
RS-422*
Bi-phase or
Manchester*
2-Wire
RS-485,
Sensornet*
4-Wire
RS-485*
Customer
Equipment
FVT107
FVR107
Customer
Equipment
Data Transmit
DIN(-)
DOUT(-)
Data Receive
Data Receive
DOUT(-)
DIN(-)
Data Transmit
Signal Ground
GND
GND
Signal Ground
Data Out (+)
DIN(+)
DOUT(+)
Data In (+)
Data Out (-)
DIN(-)
DOUT(-)
Data In (-)
Data In (+)
DOUT(+)
DIN(+)
Data Out (+)
Data In (-)
DOUT(-)
DIN(-)
Data Out (-)
Data Out (+)
DIN(+)
DOUT(+)
Data In (+)
Data Out (-)
DIN(-)
DOUT(-)
Data In (-)
Data (A)
DIN(+)
DIN(+)
Data (A)
Data (B)
DIN(-)
DIN(-)
Data (B)
Data Out (A)
DIN(+)
DOUT(+)
Data In (A)
Data Out (B)
DIN(-)
DOUT(-)
Data In (B)
Data In (A)
DOUT(+)
DIN(+)
Data Out (A)
Data In (B)
DOUT(-)
DIN(-)
Data Out (B)
* See Fig. A, Page 6 for Switch Settings
INS_FVT107_REVA
Communication Networks
3 Corporate Drive • Danbury, CT 06810 • USA • Tel: 203-796-5300 • Toll Free: 1-888-678-9427 • www.comnet.net
07/22/09
Page 8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising