DG408409

DG408409
SCOPE: IMPROVED 8-CHANNEL/DUAL 4-CHANNEL
CMOS ANALOG MULTIPLEXER
Device Type
01
02
Generic Number
DG408A(x)/883B
DG409A(x)/883B
Circuit Function
8-Channel Analog Multiplexer
Dual 4-Channel Analog Multiplexer
Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows:
Outline Letter
K
L
Z
Mil-Std-1835
GDIP1-T16 or CDIP2-T16
CDFP4-F16
CQCC1-N20
Case Outline
Package Code
16 LEAD CERDIP
J16
16 LEAD FLATPACK
F16
20-Pin Ceramic LCC
L20
Absolute Maximum Ratings
Voltage Referenced to VV+ to V- ................................................................................................................... -0.3V, 44V
V- to GND ................................................................................................................ -0.3V, 25V
Digital Inputs, S, D 1/ .............................................................................(V -) -2V to (V+ )+2V
or 30mA whichever occurs first
Continuous Current, Any terminal .................................................................................. 30mA
Peak Current, S or D (Pulsed at 1ms, 10% duty cycle max) ......................................... 100mA
Lead Temperature (soldering, 10 seconds) ........................................................................ +300°C
Storage Temperature ........................................................................................... -65°C to +150°C
Continuous Power Dissipation .........................................................................…….... TA=+70°C
16 lead FLATPACK (derate 6.1mW/°C above +70°C) .........................................…….. 485mW
16 lead CERDIP(derate 10.0mW/°C above +70°C) ...............................................……... 800mW
20 lead LCC (derate 9.1mW/°C above +70°C) ......................................................……... 727mW
Junction Temperature TJ ....................................................................................………. +150°C
Thermal Resistance, Junction to Case, ΘJC:
Case Outline 16 lead FLATPACK ........................................................…….... 65°C/W
Case Outline 16 lead CERDIP................................................................…….... 50°C/W
Case Outline 20 lead LCC ....................................................................……..... 20°C/W
Thermal Resistance, Junction to Ambient, ΘJA:
Case Outline 16 lead FLATPACK ......................................................…….... 165°C/W
Case Outline 16 lead CERDIP.............................................................……..... 100°C/W
Case Outline 20 lead LCC ..................................................................……..... 110°C/W
Recommended Operating Conditions
Ambient Operating Range (TA) ........................................................………... -55°C to +125°C
Positive Supply Voltage (V+) ...............................................................................………... +15V
Negative Supply Voltage (V-) ...............................................................................………... -15V
VAL (max) .............................................................................................................……….... 0.8V
VAH (min) ..............................................................................................................……….... 2.4V
1/ Signals on SX, DX, EN, A0, A1, A2 exceeding V+ or V- will be clamped by internal diodes.
Limit forward current to the maximum current ratings.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
----------------------------
Electrical Characteristics of DG408A/DG409A/883B
19-0088
Page 2 of
Rev. C
7
TABLE 1. ELECTRICAL TESTS: DUAL SUPPLIES
TEST
SWITCH
Analog-Signal
Range
Drain-Source On
Resistance
On-resistance
Matching between
Channels
On-resistance
Flatness
Source- Off
Leakage Current
Drain-Off Leakage
Current
Drain-On Leakage
Current
INPUT
Input
Current/Voltage
High
Input
Current/Voltage
Low
SUPPLY
Power Supply
Range
Positive Supply
Current
Negative Supply
Current
DYNAMIC
Transition Time
Break-BeforeMake interval
Symbol
CONDITIONS
-55 °C <=TA<= +125°C
V+=+15V, V-=-15V, GND=0V
VAH=+2.4V, VAL=+0.8V
Unless otherwise specified
VANALOG
rDS(ON)
∆rDS(ON
)
NOTE 3
IS =-1.0mA, VD=±10V
IS =-10mA, VD=±10V
NOTE 4
rFLAT
IS =-10mA, VD=±5V or 0V
IS(OFF)
VD=±10V VS =±10V, VEN=0V
ID(OFF)
ID(ON)
VS =±10mA, VD=±10V, VEN=0V
VD =VS=±10V, sequence each
switch on
Group A
Subgroup
Device
type
1,2,3
All
1
2,3
1
2,3
All
1
2,3
1
2,3
All
All
1
2,3
1
2,3
1
2,3
Limits
Min
2/
Limits
Max
2/
-15
15
Units
V
100
125
8
10
Ω
Ω
-0.5
-50
9
12
0.5
50
01
-1.0
-100
1.0
100
02
-1.0
-50
-1.0
-100
1.0
50
1.0
100
1.0
50
All
01
Ω
nA
nA
nA
1
2,3
02
-1.0
-50
VIN= 2.4V, 15V
1,2,3
All
-1.0
1.0
µA
VEN=0V, 2.4V; VA=0V
1,2,3
All
-1.0
1.0
µA
1,2,3
All
±4.5
±20
V
VEN=VA=0V or 4.5V
1
2,3
All
30
75
µA
VEN=2.4V, VA(ALL)=0V or 2.4V
1
2,3
1
2,3
All
0.5
2.0
1
10
mA
9
10,11
9
All
175
250
ns
IAH
IAL
I+
I-
VEN=2.4V, VA(ALL)=0V or 2.4V
tTRANS
Figure 2
tOPEN
Figure 4
----------------------------
All
-1
-10
All
10
Electrical Characteristics of DG408A/DG409A/883B
19-0088
Page 3 of
µA
ns
Rev. C
7
TABLE 1. ELECTRICAL TESTS: DUAL SUPPLIES
TEST
Enable Turn-On
Time
Enable Turn-Off
Time
Charge Injection
tON(EN)
CONDITIONS
-55 °C <=TA<= +125°C
V+=+15V, V-=-15V, GND=0V
VAH=+2.4V, VAL=+0.8V
Unless otherwise specified
Figure 3
tOFF(EN)
Figure 3
Q
Figure 5, NOTE 3
Symbol
Group A
Subgroup
9
10,11
9
10,11
9
Device
type
Limits
Min
2/
All
Limits
Max
2/
150
225
150
300
15
All
ALL
Units
ns
ns
pC
TABLE 1. ELECTRICAL TESTS: SINGLE SUPPLY
TEST
Symbol
CONDITIONS
-55 °C <=TA<= +125°C
V+=+12V, V-=0V, GND=0V
VAH=+2.4V, VAL=+0.8V
Unless otherwise specified
Group A
Subgroup
Device
type
Limits
Min
2/
Limits
Max
2/
Units
SWITCH
1,2,3
All
Analog Signal
VANALOG NOTE 3
0
12 V
Range
1
All
Drain-Source OnIS=-1.0mA, VD=3V or 10V
175 Ω
rDS(ON)
Resistance
DYNAMIC
9
All
Transition Time
VS1=8V, VS8=0V, VA=0V,
450 ns
tTRANS
NOTE 3
Figure 2
9
All
Enable Turn-On
600 ns
tON(EN) VAL=0V, VS1=5V, Figure 3
Time
NOTE 3
9
All
Enable Turn-Off
300 ns
tOFF(EN) VAL=0V, VS1=5V, Figure 3
Time
NOTE 3
NOTE 2: The algebraic convention where the most negative value is a minimum and the most positive value a
maximum is used in this data sheet.
NOTE 3: Guaranteed by design.
NOTE 4: ∆rDS(ON)= rDS(ON)max-rDS(ON)min. On-resistance match between channels and flatness are guaranteed
only with specified voltages. Flatness is defined as the difference between the maximum and minimum
value of on-resistance as measured at the extremes of the specified analog signal range.
FIGURE 2: Transition Time Diagrams: See Commercial Data Sheet
FIGURE 3: Enable Switching Time Diagrams: See Commercial Data Sheet
FIGURE 4: Break-Before-Make Interval Diagrams: See Commercial Data Sheet
FIGURE 5: Charge Injection Diagrams: See Commercial Data Sheet
----------------------------
Electrical Characteristics of DG408A/DG409A/883B
19-0088
Page 4 of
Rev. C
7
ORDERING INFORMATION:
DG408AL/883B
16 FLATPACK
DG408AK/883B
16 CDIP
DG408AZ/883B
20 LCC
DG409AL/883B
DG409AK/883B
DG409AZ/883B
TRUTH TABLE
A2
X
0
0
0
0
1
1
1
1
A1
X
0
0
1
1
0
0
1
1
A0
X
0
1
0
1
0
1
0
1
EN
0
1
1
1
1
1
1
1
1
DG408A
ON SWITCH
None
1
2
3
4
5
6
7
8
A1
X
0
0
1
1
A0
X
0
1
0
1
EN
0
1
1
1
1
DG409
ON SWITCH
None
1
2
3
4
----------------------------
TERMINAL
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
16 FLATPACK
16 CDIP
20 LCC
TERMINAL CONNECTION
01
01
DG408A
DG408A
F16 & J16
20LCC
A0
NC
EN
A0
VEN
S1
VS2
S1
S3
NC
S4
S2
D
S3
S8
S4
S7
D
S6
NC
S5
S8
V+
S7
GND
S6
A2
S5
A1
NC
V+
GND
A2
A1
Electrical Characteristics of DG408A/DG409A/883B
02
DG409A
F16 & J16
A0
EN
VS1a
S2a
S3a
S4a
Da
Db
S4b
S3b
S2b
S1b
V+
GND
A1
19-0088
Page 5 of
Rev. C
7
02
DG409A
20LCC
NC
A0
EN
VS1a
NC
S2a
S3a
S4a
Da
NC
Db
S4b
S3b
S2b
NC
S1b
V+
GND
A1
QUALITY ASSURANCE
Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in MilStd-883.
Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015:
1. Test Condition, A, B, C, or D.
2. TA = +125°C minimum.
3. Interim and final electrical test requirements shall be specified in Table 2.
Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B,
C, and D inspection.
Group A inspection:
1. Tests as specified in Table 2.
2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted.
Group C and D inspections:
a. End-point electrical parameters shall be specified in Table 1.
b. Steady-state life test, Method 1005 of Mil-Std-883:
1. Test condition A, B, C, D.
2. TA = +125°C, minimum.
3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883.
TABLE 2.
ELECTRICAL TEST REQUIREMENTS
Mil-Std-883 Test Requirements
Interim Electric Parameters
Method 5004
Final Electrical Parameters
Method 5005
Group A Test Requirements
Method 5005
Group C and D End-Point Electrical Parameters
Method 5005
*
Subgroups
per Method 5005, Table 1
1
1*, 2, 3, 9
1, 2, 3, 9, 10, 11
1
PDA applies to Subgroup 1 only.
----------------------------
Electrical Characteristics of DG408A/DG409A/883B
19-0088
Page 6 of
Rev. C
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising