Stretch It. Switch It. Split It. Gefen’s Got It.® Home Theater • Computer Audio Video • Pro A/V • Cables • Digital Signage Gefen See what’s new in 2012 8x8 Matrix for HDMI with FST and 3DTV Gefen FST Fast Switching Technology (FST) is a Gefen software implementation for HDMI products. FST was created to improve the lengthy HDMI authentication process, based on the HDMI and HDCP specifications. FST allows for connecting/disconnecting or turning any of the HDTV displays on or off without affecting other displays within the audio/video distribution system. Features* GTB-HDFST-848 Route any eight HDMI Inputs to any eight HDMI Outputs with Gefen FST and support for 3DTV The GefenToolBox 8x8 Matrix for HDMI routes eight Hi-Def sources to any eight HDTV displays. Resolutions up to 1080p Full HD and 1920x1200 plus 3DTV are supported, along with multichannel digital audio formats such as Dolby® True HD and DTS-HD Master Audio™. The 8x8 Matrix eliminates the need to disconnect and reconnect Hi-Def sources. It works with any Hi-Def source that needs to be connected to any display using HDMI. Each source can be routed to any display using the front-panel push buttons, IR remote control, RS-232 interface, or over IP using the built-in Web interface. How It Works Connect the Hi-Def audio/video sources to the eight HDMI inputs using the supplied HDMI cables. Connect up to eight displays to the HDMI outputs. 3D content can be displayed from the 3D source when a 3D-capable display is connected to Output 1. Connect the external power supply to the matrix and plug the power cable into an available electrical outlet. Apply power to all of the sources and displays. • Route any eight Hi-Def sources to any eight HDTV displays • Supports resolutions up to1080p Full HD and 12-bit Deep Color • 3DTV pass-through • Supports LPCM 7.1 audio, Dolby Digital® Plus, Dolby® TrueHD, and DTS-HD Master Audio™ • Advanced EDID Management for rapid integration of sources and displays • Gefen FST speeds up the HDCP authentication process • Fast and Slow FST Modes • Front-Panel Push-Button Switching • Supports the use of DVI sources and displays with HDMI-to-DVI cables or adapters • IP Control via Web Graphical User Interface and Telnet • RS-232 serial control for automation • IR remote control (handheld remote included) • Field-upgradable firmware via built in Web Graphical User Interface • 24V power supply • Wall-mountable • Uses Gefen Mono-LOK HDMI connectors for secure cable connections • Available in Black and White finishes Specifications* • Maximum Pixel Clock: 225 MHz • Video Input Connectors: (8) HDMI Type A 19-pin female, locking • Video Output Connectors: (8) HDMI Type A 19-pin female, locking • IP Connector: (1) RJ-45, female, Shielded • USB Port: (1) Mini-B, female • RS-232 Port: (1) DB-9, female • IR Extender Port: (1) 3.5mm mini-stereo jack • Power Supply: 24V DC • Operating Temperature: 0 - 40 °C • Dimensions (W x H x D): 9.3" x 16.85" x 1.8" (237mm x 428mm x 46mm) • Shipping Weight: 6 lbs (2.7 kg) HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing in the United States and other countries. Dolby®, Pro Logic and the double-D symbol are registered trademarks of Dolby® Laboratories. Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Copyright © 2012 Gefen, LLC All trademarks are the property ofwww.gefentoolbox.com their respective companies. *Features and specifications subject to change without notice. Gefen assumes no responsibility for any thatregistered may be contained in are this properties catalog. Inofnotheir event will Gefen, LLC be liable for direct, indirect, speAll inaccuracies trademarks and trademarks owners. cial, incidental, or consequential damages resulting from any defect or omission in this catalog, even if advised of the possibility of such damages. www.gefen.com(800)545-6900 Mini Professional Automation Control System GTB-MINI-PACS Use the Mini PACS to control your audio and video devices over your local network or over the Web The Mini Professional Automation Control System (Mini PACS) is used to control audio and video devices (such as TVs, Blu-ray players, and set-top boxes) using IP over a network. It allows control of one RS-232 serial-controlled device, three IR-controlled devices, and two relay contacts. The Mini PACS is a scaled-down version of the Gefen PACS, providing the same level of control, but has fewer input and output ports. This makes it more cost-effective for distributed control installations, or where fewer I/O ports are required. The Web user interface allows IR and two-way RS-232 commands to be sent by the Mini PACS to the connected devices to execute the desired functions. The IR and RS-232 ports can be configured, allowing the Mini PACS to be compatible with most audio and video devices. It can learn, store, and manage IR commands from other manufacturers' remotes. Two normally-open relays allow control of screens, blinds, or draperies. The Mini PACS is ideally suited for use with the Gefen Audio/Video Automation (GAVA) System Processor. However, it can be used with other control systems capable of IP communications. The Mini PACS can be mounted on a wall or any flat surface, close to the devices being controlled. Features* • Control A/V devices using IR, RS-232 control, and relays over a Web-based IP control system • Configurable Ethernet input supports Telnet, Web browsers, and TCP/IP • Web Control: User interface designed to be viewed and controlled by home automation devices, computers, and mobile devices (e.g. cell phones with Internet browsers) • Two NO (Normally Open) relay outputs plus +12V DC @ 1A and ground for convenience • Learns IR commands from manufacturer remotes, through front-panel IR receiver • Three discrete IR emitter outputs for multiple device control • Store and manage IR commands from manufacturer remotes and access them via the Web control interface. • IR commands may be uploaded from or downloaded to online libraries or PC files. • Manage RS-232 communications via Web control interface for one RS-232 device • Supports data transfer rates up to 115200 baud • Firmware upgradeable via Web interface • Configurable static IP address for stable operation • Wall-mountable Specifications* How It Works Connect the locking power supply to the Mini PACS and plug it into an available AC outlet. Connect an Ethernet cable between the Mini PACS and the local network. Access the Web interface by typing in the correct IP address on the Web browser. Configure the control interfaces (IR, RS-232, and relays) via your Web browser. Configure your automation system to send commands to the Mini PACS via IP. Connect a serial-controlled device to the RS-232 port on the Mini PACS. Plug the IR emitters into the Mini PACS and place the infrared LEDs close to the IR sensors of the A/V devices to be controlled via IR. Connect to the relay outputs as required (12V DC is also provided for convenience). Two-way RS-232 control allows device feedback to be returned to the control system over the network for accurate control. • RS-232 Serial Control Ports: (1) DB-9, female (supports Tx, Rx, and Gnd only) • IR Emitter Outputs: (3) 3.5mm two-conductor mini-jacks • Relays: (2) NO relay contacts with +12V DC and ground • Relay Connections: 6-position Phoenix terminal block • Relay Contact Rating: 1A @ 30V DC • Ethernet Port: (1) RJ-45 jack, shielded • Default IP Address: 192.168.1.72 (configurable via Web interface) • IR learning window • Power Supply: 12V DC, locking • Power Consumption: 20W (max.) / 1W (idle) • Operating Temperature: 0 - 40° C • Dimensions (W x H X D): 3.4" x 1.2" x 4.9" • (86mm x 31mm x 125mm) • Shipping Weight: 2 lbs. (0.9 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com * Features and specifications are subject to change without notice. Advanced Signal Generator for HDMI with 3D Testing Feature Small, Powerful Signal Generator for HDMI with 3DTV and KSV Testing Gefen's next-generation Mini Pattern Signal Generator for HDMI and 3DTV is designed for easy mobility when installing, designing, or troubleshooting audio/video systems in the field. Real-time testing capability for multiple displays and projectors, support for 3DTV, advanced features, and the small light-weight package, make this Signal Generator a valuable tool for integrators. The GefenTV HD Mini Pattern Signal Generator supplies 25 timings, 6 patterns, and an additional 3D testing pattern, for calibrating and testing video performance. The 3DTV test pattern supports side-by-side, top-and-bottom, and frame-packing 3D formats up to [email protected] It supports HD resolutions up to 1080p Full HD and VESA resolutions up to 1920 x 1200. The built-in audio signal generator provides up to seven channels of LPCM audio. The Audio Return Channel (ARC) can be tested via the TOSLINK digital audio output. Other features include: 12-bit Deep Color, HDCP and EDID analysis, making this device very useful for installers and integrators. This new Signal Generator can also analyze the audio/video signal on the input and display the exact video timing and audio specifications on-screen. Advanced features include a KSV count for the connected source- the HD Mini Pattern Signal Generator for HDMI and 3DTV will identify the maximum number of KSV keys the source can handle. This is extremely valuable when distributing an HDCP-compliant source to multiple displays. This model also allows you to store a display's EDID information and take it to the field. If you experience issues with signal loss when testing displays in the field, you can use either display's EDID or the previously installed EDID to overcome the issue. The easy-to-read OLED display, along with an external On-Screen Display (OSD) menu, accessed through capacitive-touch navigation buttons on top of the unit, guides users through all settings for easy operation. Its ease of use enables a professional on-site evaluation and calibration of HDTV systems, immediately locating where problems lie so they may be quickly solved. How It Works Connect an HDMI cable from the HD Mini Pattern Signal Generator to the output device (e.g. display). If testing ARC (Audio Return Channel), connect an optical cable from the output of the signal generator to the optical input of an audio amplifier.For pass-through signal analysis, from the source to the output device, connect an HDMI cable from the source to the HDMI input on the Analyzer. Connect the 5V DC power supply to the Analyzer. GTV-HD-MPSG Features* • Supports resolutions up to 1080p Full HD and 1920 x 1200 • 3D pattern support for top-bottom, side-by-side, and frame packing 3D formats • Provides 25 timings, 6 patterns and 1 pattern for 3D timing • Up to 12-bit Deep Color support at 1080p Full HD • Built-in "EDID Detective" stores EDID information for later use • Supports LPCM 7.1CH 48/96Khz, LPCM 5.1CH 48/96Khz, and LPCM 2CH 48/96/192Khz • Analyzes input source InfoFrame and output (sink) EDID • KSV (Key Selection Vector) Counter shows how many displays can be connected to an HDCP source • OLED display shows Input and Output timing information • Allows ARC (Audio Return Channel) testing by routing ARC audio to a TOSLINK (Optical) output • Touch-button control functions • Internal / External switch changes between HDMI input signal and internal Audio/Video generator • Firmware upgradeable via 3.5mm RS-232 jack (requires DB-9 to 3.5mm adapter) Specifications* • • • • • • • • • • Maximum Pixel Clock: 225 MHz HDMI Input: (1) Type-A, 19-pin, female HDMI Output: (1) Type-A, 19-pin, female Digital Audio Output: (1) TOSLINK Service Port: (1) 3.5 mm mini-stereo (for firmware upgrade) Display: OLED (Organic Light Emitting Diode) Power Supply: 5V DC Power Consumption: 3W (max.) Operating Temperature: 0° - 40° C Dimensions(W x H x D): 4.7” x 1.0” x 2.7” (120mm x 25mm x 70mm) • Shipping Weight: 1.0 lb. (0.45 kg) Gefen LLC. 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefentv.com *Features and specifications subject to change without notice. www.gefen.com(800)545-6900 4x1 A/V Switcher for HDMI extracts 5.1 Dolby Surround Sound Audio to Discrete Analog Channels GTV-AUDDEC-N Extracts Audio from Hi-Def Sources using HDMI, Delivering Dolby Digital 5.1 Surround Sound The GefenTV 4x1 HD Switcher w/ Audio Decoding is ideal for anyone wanting to create Home Cinema systems using multiple HDMI audio/video sources. It offers an easy-to-use alternative to over-complicated Home Theater Receivers, while supporting 3DTV and the latest Blu-ray audio features, or it can add HDMI connections and audio decoding to existing A/V Receivers that lack HDMI support. It decodes multi-channel surround-sound formatted digital audio from up to four HDMI sources, from coax and optical S/PDIF digital audio sources, plus a stereo analog input. Audio is output on six discrete analog RCA jacks, ready for any 5.1 channel power amplifier, or connects to the “External Processor” input on most existing A/V receivers. Dolby Digital 5.1, Dolby Pro Logic II, LPCM direct stereo and multichannel surround-sound audio formats are supported with up to six (5.1) discrete channels. The front left and front right channels feature dual outputs for bi-amplification. Advanced audio pre-processing insures an optimal surround sound signal, and a bright LCD display guides operations. RS-232 control allows connection to remote control or home automation systems, such as Gefen’s new GAVA automation system and Gefen PACS, with full feedback. How It Works Users can select audio from any one of four connected Hi-Def sources, both digital audio inputs and 2-channel analog audio. A Blu-ray player, gaming console, set-top box, DVD player, CD player and more can all be connected at the same time. If an HDMI source is selected, video is delivered in Hi-Def format to any HDTV display, and audio is delivered as 5.1 channel audio using standard RCA connectors. The HDMI output supports pass-through 3DTV making it ideal for future-proofing systems. Users can also pass-through audio using the digital and/or analog audio inputs, delivering it as up to 5.1-channel audio, enabling high quality surround-sound. When an audio input is selected, the video from the previously-selected video source is still output to the HDMI output, allowing users to watch a video source while listening to a different audio source. Users control all audio features using the IR remote or by front-panel buttons. An RS-232 port and 12V triggers allow interaction with any home automation system for added convenience. HDMI Features Supported • • • • • • 1080p Full HD Deep Color x.v.Color 3DTV pass-through Lip sync CEC pass-through Features* • • • • • • • • • • • • • Switches between four HDMI video sources to one HDMI output Supports resolutions up to 1080p Full HD Dolby Digital and Dolby Pro Logic II certified Supports Dolby® Digital 5.1, Dolby® Pro Logic II, and LPCM 5.1 (up to 6 channels) Audio switching between HDMI sources, Digital (coax and optical), and L/R analog sources Extracts encoded digital audio from HDMI, TOSLINK (Optical), or S/PDIF (Coax) inputs 12V trigger input for remote control (turns unit on when 12V is received) 12V trigger output for power amplifiers (12V DC out when unit is on) IR remote control (included) RS-232 port for automation Front-panel push-button controls Line-level volume control HDCP-compliant Specifications* • Maximum Pixel Clock: 225 MHz • Video Input Connectors: (4) HDMI Type A, 19-pin, female • Audio Input Connectors: (1) S/PDIF (Coax), (1) TOSLINK (Optical), (1) L/R analog audio (2 x RCA female) • Video Output Connector: (1) HDMI Type A, 19-pin, female • Audio Output Connectors: (8) Analog audio (RCA female) (FL, FR, C, SUB, SL, SR, Bi-Amp FL, Bi-Amp FR) • RS-232 Port: (1) DB-9, female • IR Extender Input: 3.5mm mini-stereo jack • Crosstalk: < -90 dB • Maximum Input Level: 2.2V rms • Signal-to-Noise Ratio: > 90 dB (20 Hz – 20 kHz A-weighted) • Frequency Response: 20 Hz - 20 kHz ± 0.5dB • Total Harmonic Distortion (THD+N): < 0.001% 1 kHz 2Vrms • Trigger Input: (1) 12V DC sensor (Phoenix Type terminal block) • Trigger Output: (1) 12V DC trigger (Phoenix Type terminal block) • Power Supply: 24V DC • Power Consumption: 15W (max.), 4W (standby) • Dimensions (W x H x D): 6.9” x 2.1” x 6.9” (175mm x 53mm x 175mm) • Shipping Weight: 6 lbs. (2.7 kg) ® Extend HDMI Wirelessly up to 80 feet GTV-WHD-1080P-SR Wirelessly extend HDMI video at 1080p Full HD with multichannel digital audio up to 80 feet (25 meters) The GefenTV Wireless for HDMI Extender SR system sends high definition audio and video to any HDTV display up to 80 feet (25 meters). It extends HDMI A/V content from computers using HDMI, set-top boxes, Blu-ray players, and other A/V sources to remote HDMI-compliant display(s). This wireless product is comprised of a small Sender unit and one table-top Receiver unit. It supports HD resolutions up to 1080p Full HD along with support for 7.1-channels of digital audio in PCM, Dolby®, or DTS® formats. The Wireless for HDMI Extender SR transmits within the room and does not require line-of-sight placement of transceivers for good reception. Thanks to its small form-factor and easy to plug in Sender unit, this product is ideal for high-definition A/V extension within a conference room or home theater installation that requires the quick addition of portable devices such as a presentation laptop computer or a video camera to an existing A/V system. Additional features allow multiple Sender units where each display can access up to three sources, using the included handheld remote control. How It Works Plug the Sender unit directly into the HDMI output of the source. Connect an HDMI cable from the Receiver unit to the HDTV display. When using a PC as the source, connect the supplied USB-to-mini-USB cable from the PC to the Sender unit. When using sources that do not have an available powered USB port, you will need to use the provided USB power supply. Connect the other power supply to the DC jack on the back of the Receiver unit. Connect the power supplies to available electrical outlets. If the Sender and Receiver units do not pair automatically, point the IR remote at the IR sensor window on the Receiver unit and press the Menu button. Navigate through the on-screen menu and have the Receiver unit look for a Sender unit. Press and hold the pairing button on the Sender unit until the Link LED starts blinking. Press OK on the remote. A message indicating that both the Sender and the Receiver units have been paired will appear on the display. Features* • Wireless extension of HDMI up to 80 feet (25 meters) • Supports resolutions up to 1080p Full HD • HDMI Features Supported • Dolby® TrueHD, DTS-HD® Master Audio™, and PCM digital audio streams up to 7.1 channels are supported • 3DTV pass-through • HDCP pass-through • Lip Sync • Uncompressed High Definition A/V from source to display • No latency • Included IR remote for switching between up to three Sender units • WHDI 1.0, FCC Part 15, and ETSI-compliant Specifications* • Frequency Band Range: 5.15 - 5.850 GHz • Video Input Connector (Sender): (1) HDMI Type A, 19-pin, male • Video Output Connector (Receiver): (1) HDMI Type A, 19-pin, female • USB Connector (Sender / Receiver): (1) Mini-B • Power Supply (Sender): (1) 5V/1A DC with USB jack (can also use powered USB port) • Power Supply (Receiver): (1) 5V/2A DC • Power Consumption (Sender / Receiver): 3W (max.) / 8W (max.) • Dimensions (W x H x D): • Sender Unit: 1.2” x 0.6” x 3.9” (29mm x 14.5mm x 98mm) • Receiver Unit: 5.83” x 0.8” x 3.8” (148mm x 20mm x 96mm) • Shipping Weight: 2.0 lbs. (0.9 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefentv.com *All features and specifications are subject to change without notice. www.gefen.com(800)545-6900 ® Long-Range Wireless Extension for HDMI up to 100 feet GTV-WHD-1080P-LR Wirelessly extend HDMI with multichannel digital audio up to 100 feet (30 meters) The GefenTV Wireless for HDMI Extender LR system sends high definition audio and video to any HDTV display up to 100 feet (30 meters) away. It extends HDMI from computers, set-top boxes, Blu-ray players, and other audio/video sources to a remote HDTV display. The Wireless for HDMI Extender LR supports resolutions up to 1080p Full HD along with support for 7.1-channels of digital audio in PCM, Dolby®, or DTS® formats. An IR emitter can be connected to the Sender unit and attached to the IR sensor lens of the Hi-Def source, allowing full control of the source from another room simply by pointing the IR remote at the Receiver unit. The Wireless for HDMI Extender LR transmits through walls and does not require line-of-sight for good reception. Additional features allow multiple Sender units where each display can access up to three sources, using the included handheld remote control. How It Works Connect an HDMI cable from the Hi-Def source to the Sender unit. Connect an HDMI cable from the Receiver unit to the HDTV display. Connect the included power supplies to both the Sender and Receiver units then connect the power cords to available electrical outlets. Connect an IR emitter from the Sender unit to the IR device to be controlled. Power-up the source and the display. The “Video” indicators on both units should now glow solid blue to indicate a successful connection between the Sender and Receiver unit. If the Sender and Receiver units do not pair automatically, point the IR remote at the IR sensor window on the Receiver unit and press the Menu button. Navigate through the on-screen menu and have the Receiver unit look for a Sender unit. Press and hold the pairing button on the Sender unit until the Link LED starts blinking. Press the OK button on the IR remote. A message indicating that the Sender and the Receiver units have been paired will appear on the display. Point the source’s IR remote at the IR window on the Receiver unit to control the source** that is placed near the Sender unit. Features* • Wireless extension of HDMI up to 100 feet (30 meters) • Supports resolutions up to 1080p Full HD • HDMI Features Supported • Dolby® TrueHD, DTS-HD® Master Audio™, and PCM digital audio streams up to 7.1 channels are supported • 3DTV pass-through • HDCP pass-through • Lip Sync • No latency • Included IR remote for switching between up to three Sender units • WHDI 1.0, FCC Part 15, and ETSI-compliant Specifications* • Frequency Band Range: 5.125 - 5.850 GHz • Video Input Connector (Sender): (1) HDMI Type A, 19-pin, female • Video Output Connector (Receiver): (1) HDMI Type A, 19-pin, female • USB Connector (Sender / Receiver): (1) Mini-B • Power Supply (Sender/Receiver): (2) 5V DC • Power Consumption (Sender / Receiver): 8W (max.) / 8W (max.) • Dimensions (Sender / Receiver) (W x H x D) 5.83” x 0.8” x 3.8” (148mm x 20mm x 96mm) • Shipping Weight: 2.8 lbs. (1.27 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefentv.com *All features and specifications are subject to change without notice. 32x32 Modular Matrix GEF-MOD-32432 Route any 32 DVI Sources to any 32 Displays and extend outputs using CAT-5 or Fiber Optic cables The GefenPRO 32x32 Modular Matrix provides an all-in-one professional-grade solution to route up to 32 DVI sources to any 32 DVI displays with resolutions up to 1920 x 1200. The modular design of this matrix provides the ultimate in flexibility by allowing the use of any combination of DVI, ELR, or 1FO output modules in any of its four output slots. This feature allows the GefenPRO 32x32 Modular Matrix to function as both a Matrix and as an Extender. The front-panel LCD displays the current routing status and each DVI source is accessible to any display by using the front-panel push buttons, via the RS-232 interface, or through IP Control (built-in Web server and Telnet). Hot-swappable dual redundant power supplies allow these matrixes to be used for applications in demanding applications where enhanced reliability, ease of servicing and zero down-time are required. How It Works Connect up to 32 DVI source devices using DVI cables to the inputs on the GefenPRO Modular Matrix. Connect up to 32 displays via DVI, CAT-5, or Fiber Optic cables depending on which output modules are utilized. Connect an Ethernet cable from the network to the RJ-45 connector to use the built-in Web server or Telnet capability to control routing, EDID, and other functions. Connect an RS-232 cable from a RS-232 control device to control the matrix via RS-232. Connect the IEC connectors of the included AC power cords to the matrix and plug the power cords into available electrical outlets. The DVI sources will be routed as selected. Features* • Supports resolutions up to 1920 x 1200 • Modular inputs and outputs organized into banks of 8 • Advanced EDID management for rapid integration of sources and displays • RS-232 Serial interface for remote control via a computer or automation control system • Front-panel LCD display • Front-panel push buttons for local switching • Built-in Web server and Telnet control via IP • Routing states can be stored and recalled at the touch of a button • Dual redundant hot-swappable power supplies • Removable and replaceable fan and filter modules • Output masking command • Standby mode • Power ON / OFF switch • Rack-mountable Specifications* • • • • • • • • • • Maximum Pixel Clock: 165 MHz Input Video Signal: 1.2V p-p DVI Input Connectors: (32) DVI-I 29-pin, female Output Connectors: (32), organized into banks of 8 depending upon the type of output module used: • DVI: (8) DVI-I, 29-pin, female (digital only) • ELR-POL: (8) RJ-45 • Fiber: (8) SC (single fiber) RS-232 serial port: DB-9, female Ethernet (IP control) port: RJ-45 jack (100BaseT) Power Supplies: (2) 100 - 240V AC (dual IEC hot-swappable) Rack-Mountable: 6U rack height, rack ears included Dimensions (W x H x D): 17.6” x 10.5” x 19” D (447mm x 266mm x 482mm ) Shipping Weight: 44 lbs. (20 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefenpro.com www.gefen.com(800)545-6900 ELR-POL Extender for GefenPRO Modular Matrixes GEF-DVI-8ELR-S GEF-DVI-ELRPOL-R Extend DVI from a GefenPRO Modular Matrix up to 330 feet (100 meters) over CAT-5 The GefenPRO Modular Matrix DVI ELR-POL Sender over CAT-5 can be installed in any one (or all) of the output slots on any GefenPRO Modular Matrix, allowing DVI signals to be extended up to 330 feet (100 meters). Use the GefenPRO DVI ELR Receiver with POL to complete the connection to the display. Gefen POL (Power Over Link) technology supplies power to the Receiver unit without the need for a power supply. How It Works Install the Sender module(s) into the GefenPRO Modular Matrix output slot(s). Connect a single CAT-5 cable up to 330 feet (100 meters) in length between each output of the Sender module and a Receiver unit. The Receiver unit will draw power from the Sender module over the CAT-5 cable. Connect the DVI output from the ELR-POL Receiver unit to a Hi-Def display. Power up the source(s), the display(s), and the GefenPRO Modular Matrix. Features* • • • • • • • • Plug-in Sender module for GefenPRO Modular Matrix Extends DVI up to 330 feet (100 meters) Supports resolutions up to 1920 x 1200 Uses Gefen POL (Power Over Link) technology to supply power to the Receiver unit EDID management provides rapid integration between souce and display DDC pass-through LED Indicators for Power, Link Status, and POL Status Firmware can be updated via IP Specifications* • Maximum Pixel Clock: 165 MHz Sender module: • ELR Connectors: (8) RJ-45, shielded per output (1 per output) • Dimensions (W x H x D): 15.75” x 1” x 10.5” (400mm x 26mm x 267mm) • Shipping Weight: 2 lbs (0.9 kg) Receiver unit: • Video Output Connector: (1) DVI-I, 29-pin, female (digital only) • ELR Connector: (1) RJ-45, shielded • Dimensions (W x H x D): 4.3” x 3.4” x 1.1” (110mm x 85mm x 28mm) • Shipping Weight: 1.4 lbs (0.64 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefenpro.com Fiber Optic Extender for GefenPRO Modular Matrixes GEF-DVI-8FO-S GEF-DVI-1FO-R Extend DVI from the Gefen Modular Matrix over Fiber Optic cable up to 6600 feet (2000 meters) The GefenPRO 8 DVI Extender over One Fiber Sender module can be installed in any one (or all) of the output slots on a GefenPRO Modular Matrix, allowing DVI signals to be extended up to 6600 feet (2000 meters). Use the GefenPRO DVI Extender over One Fiber Receiver unit to complete the connection to the display. How It Works Install the Sender module(s) into the GefenPRO Modular Matrix output slot(s). Connect one strand of multimode SC fiber from each fiber optic connector on the Sender module to each Receiver unit. Connect the power supply to the DC jack on the Receiver unit then connect the power supply to an available electrical outlet. Power up the source(s), the display(s), and the GefenPRO Modular Matrix. Features* • Plug-in Sender module for GefenPRO Modular Matrix • Extends DVI up to: • 6600 feet (2000 meters) using 50µ OM3e multi-mode fiber optic cable • 2000 feet (600 meters) using 50µ OM3 multi-mode fiber optic cable • 660 feet (200 meters) using 62.5µ OM1 multi-mode fiber optic cable • Supports resolutions up to 1920 x 1200 • EDID management provides rapid integration between sources and displays • LED Indicators for Power and Link Status • Firmware can be updated via RS-232 or Ethernet ports of a GefenPRO Modular Matrix Specifications* • Maximum Pixel Clock: 165 MHz Sender module: • Fiber Optic Connectors: (1) SC type per output (8 total) • Dimensions (W x H x D): 15.75” x 1” x 10.5” (400mm x 26mm x 267mm) • Shipping Weight: 2 lbs (0.9 kg) Receiver unit: Video Output Connector: (1) DVI-I, 29-pin, female (digital only) Fiber Optic Connector: (1) SC type Power Supply: 5V, locking Power Consumption: 10W (max.) Dimensions (W x H x D): 4.3” x 3.4” x 1.1” (110mm x 85mm x 28mm) • Shipping Weight: 1.4 lbs (0.64 kg) • • • • • Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefenpro.com *Features and specifications are subject to change without notice. www.gefen.com(800)545-6900 8x8 Matrix for HDMI with Four ELR-POL and Four HDMI Outputs Features* • • • • • • • GEF-HDFST-848-4ELR Route any eight HDMI sources to any eight HDMI outputs and extend four HDMI outputs over one CAT-5e cable up to 330 feet (100 meters) The GefenPRO 8x8 Matrix with four ELR and four HDMI outputs routes up to eight Hi-Def sources at resolutions up to 1080p Full HD with Deep Color and multi-channel digital audio to any of eight HDTV displays, eliminating the need to disconnect and reconnect HDMI sources and displays. It features extension of four displays up to 330 feet (100 meters), using Gefen’s ELR (Extra Long Range) and POL (Power Over Link) technologies. ELR extension on four outputs allows installation of displays over a single CAT-5e cable. POL eliminates the need to externally power the four included ELR receivers. The GefenPRO 8x8 Matrix supports 3DTV and advanced digital audio formats such as Dolby® TrueHD and DTS-HD® Master Audio™. Each source is accessible at all times from any display by using the included IR Remote Control, the RS-232 port, IP (Telnet or Web GUI), or by using the front-panel push buttons. How It Works Using HDMI cables, connect up to eight Hi-Def sources to the HDMI inputs on the matrix. Connect up to four HDTV displays to the HDMI outputs on the matrix and up to four HDTV displays to the supplied ELR-POL receivers. Use a single CAT-5e cable to connect each of the receivers to the matrix. An external power supply is not required because power is delivered by the matrix over the CAT-5e cables. 3D content can be displayed when connecting a 3DTV and 3D source.Connect the included AC power cord to the matrix and plug it into an available electrical outlet. Turn on the matrix by pressing the power switch. Apply power to sources and to the displays. The Hi-Def sources can now be routed to any display by using the IR remote control, RS-232 port, IP (Telnet or Web GUI), or by using the front-panel push buttons. Gefen FST Fast Switching Technology (FST) is a Gefen software implementation for HDMI products. FST was created to improve the lengthy HDMI authentication process, based on the HDMI and HDCP specifications. FST allows connecting/disconnecting or turning any of the HDTV displays on or off without affecting other displays within the audio/video distribution system. Routes any eight Hi-Def sources to any of eight HD displays, independently Includes four ELR-POL receivers ELR technology allows extension up to 330 feet (100 meters) POL feature provides power to each ELR receiver Uses HDBaseT® technology Supports resolutions up to 1080p Full HD HDMI Features Supported: • 12-bit Deep Color • x.v. Color • LPCM 7.1 audio, Dolby® TrueHD, Dolby Digital® Plus, and DTS-HD® Master Audio™ • 3DTV pass-through • Lip Sync pass-through • Gefen FST speeds up the HDCP authentication process • Fast and Slow FST Modes • Advanced EDID Management for rapid integration of sources and displays • Ability to save and recall presets • Supports DVI sources and displays • Field-upgradeable firmware via IP • Front Panel Switching • IR Control via front panel sensor and back panel input (using EXT-RMT-EXTIR-N) • Serial (RS-232) control for automation • IP Control via Web Server and Telnet • Rack mountable (2U tall, rack ears included) • Internal power supply with detachable IEC AC cord • Back panel master power switch Specifications* • Maximum Pixel Clock: 225 MHz • Matrix Video Input Connectors: (8) HDMI Type A 19-pin, female, locking • Matrix Video Output Connectors: (4) HDMI Type A 19-pin, female, locking (4) ELR-POL RJ45, female • Receiver ELR-POL Input Connector: (1) RJ45, female • Receiver Video Output Connector: (1) HDMI Type A 19-pin, female, locking • Power Indicator (Matrix/Receiver): LED, blue=On, red=Standby • Lock Indicator (Matrix): LED, blue • USB Port (Matrix): Mini-B, female • Ethernet Port (Matrix): (1) RJ45, female, 10/100 BaseT • RS-232 Port (Matrix): (1) DB-9, female • IR Extender Port (Matrix): (1) 3.5mm mini-stereo jack • Power Supply: Internal, 100V to 240V AC, 50/60 Hz, detachable IEC cord • Power Consumption (Matrix): 120W (max.) • Operating Temperature: 0 to + 40 °C • Rack mounting requirements (Matrix): Standard 19” rack, 2U high • Dimensions (Matrix - W x H x D): 17.25" x 3.5" x 12" (440mm x 89mm x 305mm) • Dimensions (Receivers - W x H x D): 4.4" x 1.1" x 3.35" (110mm x 27mm x 85mm) • Shipping Weight (1 Matrix and 4 Receivers): 37 lbs (16.8 kg) ® ® FAST SWITCHING TECHNOLOGY Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefenpro.com *All features and specifications subject to change without notice. All trademarks and registered trademarks are properties of their respective owners. Digital Audio De-Embedder for SDI GEF-SDI-AUDD Remove and independently route audio data from an SDI source to any four audio outputs The GefenPRO 3GSDI Audio De-Embedder extracts audio from 3GSDI, Single Link HD-SDI, and SDI video signals. Up to four AES/EBU digital audio streams can be de-embedded and routed to any of the four audio outputs. Selection and routing of each audio group / pair can be configured via RS-232. How It Works Connect an SDI source to the SDI In connector. Connect the SDI Loop Out connector to an SDI audio/video device to monitor the original unmodified signal. Connect the Output connector to an SDI acceptor (such as video broadcast equipment). Connect up to four AES/EBU digital audio reproduction devices (such as a DAT recorder or pre-amp) to the Audio Out connectors. Connect the RS-232 cable from the Audio De-Embedder to a PC or automation system to control which audio group will be de-embedded from the video signal. Connect the AC power cord to the 3GSDI Audio De-Embedder and to an available electrical outlet. Once the unit is powered, RS-232 commands can be used to select the audio group and pair to be de-embedded from the video signal. NOTE: This product is not compatible with dual-link HD-SDI sources. Features* • • • • • • • • Supports SDI, ED-SDI, Single-Link HD-SDI, and 3G-SDI Allows individual digital audio channels to be re-arranged on the output Audio delay adjustment for each pair of audio outputs (0 – 150 ms) 3G-SDI detection LED Status Indicators Standby Mode Recovers to the previous state if power is interrupted Firmware upgradeable via RS-232 interface Specifications* • • • • • • • • • • • • Supported formats: • SDI (SMPTE 259M) • ED-SDI (SMPTE 344M) • Single-Link HD-SDI (SMPTE 292M) • 3G-SDI (SMPTE 424M) SDI Input Connector: (1) BNC, female SDI Loop Out Connector: (1) BNC, female SDI Output Connector: (1) BNC, female Digital Audio Output Connectors: (4) BNC, female RS-232 Connector: (1) DB-9, female Power On Indicator: (1) LED, blue 3G-SDI Indicator: (1) LED, blue Audio De-embedder Indicator: (1) LED, blue SDI/HD-SDI Signal Indicator: (1) LED, bi-color (green/blue) Power Supply: 100 - 240V AC (Internal) AC Power Connector: IEC Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefenpro.com www.gefen.com(800)545-6900 Digital Audio Embedder for SDI GEF-SDI-AUDE Embed up to four audio streams onto an SDI signal Features* The GefenPRO 3GSDI Audio Embedder allows you to embed up to four AES/EBU digital audio streams into an SDI, ED-SDI, HD-SDI, or 3G-SDI signal. Selection and routing of each audio group / pair can be configured via RS-232. • • How It Works Connect an SDI source to the SDI input BNC connector. Optionally connect the SDI Loop Out BNC connector to a display for monitoring the unprocessed signal. Connect the Output BNC connector to an SDI + AES/EBU acceptor (such as video broadcast equipment). Connect up to four AES/EBU digital audio sources (such as DAT-Players) to the Audio In BNC connectors. Connect an RS-232 cable from the Audio Embedder to a PC or home automation system. Connect the AC power cord to the Audio Embedder and power on the unit. RS-232 commands can be sent from the PC or automation system to select the audio group and pair to be embedded into the video signal. NOTE: This product is not compatible with dual-link HD-SDI sources. • • • • • • Supports SDI, ED-SDI, Single Link HD-SDI, and 3G-SDI Allows individual digital audio channels to be re-arranged on the output Audio delay adjustment for each pair of audio outputs (0 – 150 ms) 3G-SDI detection LED Status Indicators Standby Mode Recovers to the previous state if power is interrupted Firmware upgradeable via RS-232 interface Specifications* • • • • • • • • • • • • Supported formats: • SDI (SMPTE 259M) • ED-SDI (SMPTE 344M) • Single-Link HD-SDI (SMPTE 292M) • 3G-SDI (SMPTE 424M) SDI Input Connector: (1) BNC, female SDI Loop Out Connector: (1) BNC, female SDI Output Connector: (1) BNC, female Digital Audio Input Connectors: (4) BNC, female RS-232 Connector: (1) DB-9, female Power On Indicator: (1) LED, blue 3G-SDI Indicator: (1) LED, blue Audio Embedder Indicator: (1) LED, blue SDI/HD-SDI Signal Indicator: (1) LED, bi-color (green/blue) Power Supply: 100 - 240V AC (Internal) AC Power Connector: IEC Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefenpro.com 3G-SDI Scaler with Genlock and Frame Synchronization Features* • • • • • • • • • • Digital audio output Adjustable cadence detection Advanced noise reduction and detail enhancement Frame-rate conversion Fully integrated sprite-based Menu System Built-in pattern generator with Color Bars and Hatch Pattern RS-232 Control IR Remote Control (included) Field-upgradeable firmware via USB port Rack-mountable (rack ears included) Specifications* GEF-3GSDI-2-3GSDIS • Scale and synchronize SDI, HD-SDI, or 3G-SDI signals The GefenPRO 3GSDI-2-3GSDIS provides high-performance scaling - including adjustable cadence detection, frame rate conversion, detail enhancement, and advanced noise reduction. • It works with SDI, ED-SDI, HD-SDI, or 3G-SDI signals and supports resolutions up to 1080p Full HD and 2048 x 1080 (2K). This product can be used as a standalone frame synchronizer without scaling if desired. When frame synchronization is required, the video output of one source (or a reference signal) can be used to Genlock another input source. Genlock Mode, as well as all features of this scaler, can be controlled through the built-in menu system using the IR Remote Control or via RS-232 control. • • • How It Works Connect SDI source devices to the SDI inputs and connect downstream equipment to the SDI outputs. Convenient SDI loop-through output connectors and an RCA Coax (S/PDIF) audio output allow monitoring of SDI video and audio. An external Genlock source may also be connected. Configuration may be done using the IR Remote and the On-Screen Display (OSD) menu, or via the RS-232 port. A USB port is also provided for future firmware upgrades. • • • Supported standards: • SD-SDI (SMPTE 259M) • ED-SDI (SMPTE 344M) • HD-SDI (SMPTE 292M) • Dual-Link HD-SDI (SMPTE 372M) • 3G-SDI (SMPTE 424M Supported resolutions: • 525i / 720p / 1080i @ 59.94Hz • 1080p @ 23.98Hz • 625i / 720p / 1080i @ 50Hz • 1080p @ 24Hz • 1080i / 720p @ 60Hz • 2K Input Video Bandwidth: 2 x 2.97 Gbps Output Video Bandwidth: 2 x 2.97 Gbps Connnectors: • SDI Inputs: (2) BNC female • SDI Outputs: (2) BNC female • Genlock Input: (1) BNC female • Digital Audio S/PDIF Output: (1) RCA female • USB Port (1): Type B female • RS-232 Port (1): DB-9 female • AC Inlet: (1) IEC type Power Supply: 110/220V (internal) Dimensions (W x H x D): 16.8” x 1.75” x 7” (428mm x 44.5mm x 178mm) Shipping Weight: 6 lbs (2.72 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefenpro.com www.gefen.com(800)545-6900 Professional Automation Control System EXT-PACS Control any RS-232, IR, or 12V trigger-controlled device through a Web or IP interface The Professional Automation Control System (PACS) allows control of Gefen products and other A/V devices (e.g. displays, Blu-ray players, cable/satellite boxes, Lighting systems, motorized screens, etc.) through any Web-enabled smartphone, WiFi tablet, laptop, or automation system. The Web user interface allows IR, RS-232, and 12V trigger commands to be sent by the PACS to the connected devices to execute the desired functions. The IR, RS-232, and 12V DC triggers can be configured, allowing the PACS to be compatible with most A/V devices. It can learn, store, and manage IR commands of different manufacturers’ remotes. The PACS is particularly suitable for use with the Gefen GAVA Automation System Processor; however it can be used in other systems capable of programmable IP communications or it can be configured as an RS-232-to-IR bridge. • 10 Trigger outputs (+12V, floating, or ground-referenced). • Learns IR commands from manufacturer remotes, through front-panel IR receiver. • Store and manage IR commands from manufacturer remotes and access them via the Web control interface. • Eight discrete IR emitter outputs for multiple device control. • Manage RS-232 commands via Web control interface for up to three RS-232 devices. • Supports data transfer rates up to 115200 baud. • Firmware upgradeable via Web interface. • Rack-mountable using the 1U Rack Tray (Gefen part no. EXT-RACK-1U). How It Works Connect the serial-controlled devices to the PACS RS-232 outputs. Plug the IR emitters into the PACS and place the LED emitters close to the IR sensors of the A/V devices to be controlled. Connect trigger leads of various devices to the trigger outputs on the back panel. Connect the locking power supply to the PACS. Connect an Ethernet cable between the PACS and the local network. Access the Web interface by typing in the correct IP address on the Web browser. Configure the control interfaces (IR, RS-232, 12V triggers) via your Web browser. Configure the Automation System to send commands to the PACS via IP. Specifications* • RS-232 Serial Control Ports: (3) DB-9, female (supports Tx, Rx, and Gnd only) • IR Emitter Outputs: (8) 3.5mm two-conductor mini-jacks • Output Triggers: (10) pairs Phoenix Connectors (+12V DC, 100mA max.) • Ethernet Port: (1) RJ-45 jack, shielded • IR learning window • Power Supply: 12V DC, Locking • Power Consumption: 20W (max.) / 2W (standby) Features • Operating Temperature: 0 - 40° C • Control AV devices using IR, RS-232 control, and 12V triggers over a Web based IP control system. • Dimensions: 8.4” W x 4.3” D x 1.65” H • Configurable Ethernet input supports Telnet, Web browsers, and TCP/IP. • Shipping Weight: 4 lbs. • Web Control: User interface designed to be viewed and controlled by home automation devices, computers, and mobile devices (i.e. cell phones with Internet browsers). Gefen LLC. 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com GAVA Audio/Video Automation System Processor EXT-GAVA Control Your Home A/V and Lighting from your Smartphone, Tablet, or Web Browser Gefen introduces its new GAVA Audio / Video Automation System- a new way to control your home. This new system works in concert with Gefen's PACS (Professional Automation Control System) and Mini-PACS hardware to control all key audio/video features in a home or commercial environment, as well as automation of lighting, temperature, window shades and more. In a typical home entertainment scenario, users have multiple sources, such as Blu-ray players, Apple TV®, iTunes®, satellite or cable set-top boxes, and more, all connected in a system with one or more displays. What makes the Gefen GAVA System unique, is its ability to control applications on a home or business network rather than on a stand-alone controller with dedicated cabling. This makes it ideal for retrofit or distributed systems. Another unique GAVA feature is its ability to connect over your network with Apple TV 2 and computers (Mac or PC) running iTunes, with display of Cover Art and song metadata. The GAVA system is specifically designed to allow control through an interface that works with all smartphones and tablets today. It is optimized for the iPad®, iPod touch®, iPhone®, Android™ phones, and other smartphones, as well as Android™ and other tablets. How It Works Simply connect all your IR and RS-232-controlled equipment to the Gefen EXT-PACS Controller. Then connect the EXT-GAVA Control Processor and PACS to your network. Make sure your mobile devices are configured for WiFi access to your network. Open a Web browser on your PC or Mac to configure your GAVA system. Just select your components from GAVA's library, and configure connections from pull-down menus. Open your mobile device's Web browser and point it to the GAVA Web page and you're ready to go. On iOS devices, click the "Add to Home Screen" button to create a GAVA icon for immediate one-touch access to your system. Features* • Integrated HTML5 Web Server supports any smartphone or Web client • Intuitive Graphical User Interface (GUI) • Local low-power Linux processor contains system controllers, device interface codes, and a web server • Easy Wizard setup with no programming required • Simple configuration interface • Directly controls Gefen IP-controlled devices and other selected IP devices • Offers control (through EXT-PACS) of any IR and RS-232-controlled devices, and trigger contacts. • May be powered over Ethernet cable with optional power adapter • Fan-less, silent, low-power processor may be placed anywhere • Full two-way control of RS-232 and IP devices • 2-way IP interface with Apple TV and computers running iTunes (PC or Mac) • One or more PACS controllers may be located anywhere on the Network • Offers Z-Wave interface for lighting, appliance control, and more • Other lighting and appliance interfaces (Lutron, etc.) coming soon • Supports UPnP IP devices Specifications* GAVA is designed for quick installation- only a single cable is needed, and the Configuration Wizard allows a system to be installed and configured in less than half an hour! • Network Port: RJ-45 • USB Ports: (2) Type A • RS-232 Serial Port: DB-9, female (for future use) • Power Supply: 18V DC 1.2A • Power Consumption: 2.5W (Idle), 25W (max.) • Dimensions: 4.2" W x 6.4" D x 1.2" H • Shipping Weight: 1 lb. Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com *Features and specifications are subject to change without notice. All trademarks are the properties of their respective owners. www.gefen.com(800)545-6900 Distribute a DisplayPort source to four locations EXT-DP-144 Distribute a DisplayPort source to four locations Features* The Gefen 1:4 Splitter for DisplayPort allows a DisplayPort-equipped source to be connected to four DisplayPort displays. EDID management provides rapid integration of source and displays. Two or more of these splitters can be connected together to create larger video distribution networks. • • • • • How It Works Specifications* Connect a DisplayPort source to the input on the splitter using the supplied DisplayPort cable. Connect up to four DisplayPort high-definition displays to the outputs of the 1:4 Splitter for DisplayPort. • • • • • • • • • NOTE: If the source and/or displays are not 100% DisplayPort compliant, a protocol-specific adapter will be required in order to connect the non-compliant source to the splitter, or to connect the splitter to the non-compliant display. Simultaneously displays one DisplayPort source on up to four displays Supports resolutions up to 2560 x 1600 EDID Management for rapid integration of source and displays EDID Reset button Supports up to 7.1 channels of linear PCM audio (32 kHz - 192 kHz sampling rate) • Supports DisplayPort 1.1a Maximum Pixel Clock: 300 MHz Maximum Data Rate: 10.8 Gbps Maximum Resolution: 2560 x 1600 Video Input Connector: (1) DisplayPort, female Video Output Connectors: (4) DisplayPort, female Power Supply: 5V / 3A DC Power Consumption: 15W (max.) Operating Temperature: 0 - 40° C Dimensions (W x H x D): 10.75” x 1.25” x 5.25” (274mm x 32mm x 134mm) • Shipping Weight: 3 lbs. (1.2 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com Extend the range of DisplayPort up to 150 feet EXT-DP-141B Extend the range of copper DisplayPort cables Features* The Gefen DisplayPort Booster allows extension of DisplayPort up to 150 feet at 1920 x 1200 (WUXGA) and 100 feet at 2560 x 1600 (WQXGA), using high-quality copper DisplayPort cables. The Gefen DisplayPort Booster improves the reliability of HDCP and DPCD handshaking and EDID transmission over long distances of copper cable. This product is DisplayPort 1.1-compliant. • • • • • • • Extends DisplayPort up to 150 feet (45 meters) Supports resolutions up to 2560 x 1600 (WQXGA) EQ trim-switch for optimal signal quality at varying distances External 5V DC power supply HDCP, DPCD, and DDC pass-through DisplayPort 1.1-compliant Compact design How It Works Connect a DisplayPort cable between the DisplayPort source and the Gefen DisplayPort Booster input. Connect a short DisplayPort cable from the DisplayPort Booster output to the display. If power from DisplayPort source is insufficient or not available, connect a 5V DC power supply to the DisplayPort booster. Specifications* • • • • • • • • • Video Input Connector: (1) DisplayPort, 20-pin, female Video Output Connector: (1) DisplayPort, 20-pin, female Coarse EQ adjustment: (2) DIP Switches Fine EQ trim adjustment: (1) 8-position rotary switch Power Indicator: (1) LED, blue Power Supply: 5V DC Power Consumption: 5W (max.) Dimensions (W x H x D): 2.2” x 0.8” x 2” (55mm x 20mm x 50mm) Shipping Weight: 1.0 lb. (0.45 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com *All features and specifications are subject to change without notice. All trademarks and registered trademarks are properties of their respective owners. www.gefen.com(800)545-6900 Stay in Sync, EDID Detective for DisplayPort EXT-DP-EDIDP Save the DisplayPort EDID from the display to the source Computers and other Hi-Def video source devices can sometimes lose the EDID (Extended Display Identification Data), when switched away from the source. When displays are switched off (or disconnected and reconnected), EDID can also be lost and a computer or a Hi-Def video device may no longer be able to show the video properly. The Gefen DisplayPort Detective Plus allows an EDID to be pre-set or recorded from a display. The data is then stored in non-volatile memory. The display can then be switched or relocated to a different source, providing the new source with the correct video. External DIP switches can provide instant access to pre-programmed EDID banks, providing rapid integration of your source and display. How It Works Connect a DisplayPort cable from the display to the output port of the DisplayPort Detective Plus. To copy the EDID from the display, connect the included 5V DC power supply or a powered USB port to the DisplayPort Detective Plus. Press and hold the Program button on the front panel to record the EDID of the connected display. Remove the power supply and connect the source to the input port using the included DisplayPort cable. Features* • • • • • • • • • Supports resolutions up to 2560 x 1600 (WQXGA) EDID presets for custom resolution support Supports RGB and YCbCr color spaces Write-protect switch No power supply required after initial EDID programming Can be powered via USB port or the included power supply Upload / download EDID (.bin) files Copy EDID from connected display into non-volatile internal memory Firmware upgradeable Specifications* • • • • • • • • • • Video Input Connector: (1) DisplayPort, 20-pin, female Video Output Connector: (1) DisplayPort, 20-pin, female USB Connector: (1) USB Mini-B DIP Switches: (4) DIP switches, pre-programmed EDID selection Write-protect Switch: (1) 2-position, slide Program button: (1) Push button, momentary Status Indicator: (1) LED, bi-color (blue / red) Power Supply: 5V DC Dimensions (W x H x D): 4.25” x 1” x 3.4” (108mm x 25mm x 87mm) Shipping Weight: 1.5 lbs. (0.70 kg) Note: The 5V power supply is needed only to record the display EDID. For normal operation, leave the power supply disconnected. Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com *All features and specifications are subject to change without notice. All trademarks and registered trademarks are properties of their respective owners. Small Fiber Optic Pigtail Module Extends DisplayPort up to 1000 feet EXT-DP-CP-FM10 Pigtail module DisplayPort extension using a singlestrand multimode fiber optic cable with DPCD support. The DisplayPort fiber optic pigtail module extender with DPCD support extends a DisplayPort up to 1000 feet (300 meters) using a singlestrand 50/125µm multimode (OM2) SC-terminated fiber optic cable with resolutions up to 2560 x 1600 (WQXGA). Optical signal transmission provides galvanic isolation and immunity to electromagnetic interference compared to similar copper based extension modules. The pigtail design of the Sender and Receiver modules relieves stress and clutter on the source and display connector panels. Their compact design makes them ideal for fitting neatly behind equipment for a clean installation, making it a great way to easily extend DisplayPort. How It Works The Sender pigtail end plugs into the DisplayPort source. The Receiver pigtail end plugs into the display. Connect a single-strand 50/125µm multimode (OM2) SC-terminated fiber optic cable from the Sender to the Receiver module. Plug the power supply into the Receiver module and a vibrant Hi-Def picture will appear on your display. Note: The Sender module does not need to be powered externally unless the source does not supply enough power through the DisplayPort connector. Features* • Extends DisplayPort up to 1000 feet (300 meters) over a single-strand 50/125µm multimode (OM2) SC-terminated fiber optic cable • Compliant with DisplayPort 1.1standard • Supports resolutions up to 2560 x 1600 (WQXGA) • Fiber optic transmission eliminates electromagnetic interference (EMI) • Pigtail design relieves stress and clutter on the source and display connector panels • DPCD compliant • DDC bidirectional support • Compact Sender and Receiver modules provide a clean, easy installation • FCC and CE compliant for EMI/RFI emission Specifications* • Video bandwidth: 3.5Gbps/Channel • Video Input Connector (Sender): (1) DP-20-pin, male • Video Output Connector (Receiver): (1) DP-20-pin, male • Link Connector (Sender/Receiver): (1) Type SC fiber (50 /125µm ) • Power Supply (Receiver): 5V DC • Power Supply (Sender): 5V DC (not needed for most applications) • Power Consumption (Receiver): 1.5W (max.) • Operating Temperature: 0° to + 50° C • Storage Temperature: -20° to + 70° C • Relative Humidity: 10 to + 80% • Dimensions (W x H x D): 1.50" x 0.47" x 3.51" (38.10mm x 11.93mm x 89.15 mm) • Shipping Weight: 1lb (0.45 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com *All features and specifications subject to change without notice. All trademarks are the property of their respective owners. www.gefen.com(800)545-6900 l Fiber Optic Pigtail Module Smallfeet Fiber Optic Pigtail Module ends HDMI up to 1000 Extends HDMI up to 1000 feet EXT-HD-CP-FM10 Features* sing a singlee with HDCP Pigtail module •HDMI extension a singleExtends HDMI up tousing 1000 feet (300 meters) using aFeatures* single-strand multimode SC-terminated fiber optic cable strand multimode50/125µm fiber optic cable (OM2) with HDCP • Extends HDMI up to 1000 feet (300 meters) using a single-strand • Supports resolutions up 1080p Full HD with HDCPsupport support • Supports HD lossless audio: LCPM 7.1 audio, Dolby® 50/125µm Digital Plus,multimode (OM2) SC-terminated fiber optic cable using a single-strand • Supports resolutions up 1080p Full HD Dolby® TrueHD, and DTS-HD® Master Audio™ The HDMI fiber optic cable. It fiber optic pigtail module extender with HDCP support • Supports HD • Fiber optic transmission eliminates electromagnetic interference (EMI)lossless audio: LCPM 7.1 audio, Dolby® Digital Plus, extends d HD lossless audioHDMI up to 1000 feet (300 meters) using a single-strand Dolby® TrueHD, and DTS-HD® Master Audio™ • Pigtail design relieves stress and clutter on the source and display 50/125µm Plus, Dolby® TrueHD, multimode (OM2) SC-terminated fiber optic cable. It • Fiber optic transmission eliminates electromagnetic interference (EMI) connector panels supports resolutions up to 1080p Full HD and HD lossless audio al transmission provides • Pigtail design relieves stress and clutter on the source and display • 3DTV formats like LCPM 7.1 audio,pass-through Dolby® Digital Plus, Dolby® TrueHD, agnetic interference connector panels • DDC bidirectional support modules. and DTS-HD® Master Audio™. Optical signal transmission provides • 3DTV pass-through • immunity HDCP pass-through galvanic isolation and to electromagnetic interference • DDC bidirectional support • Supports Deep Color compared modules relieves stressto similar copper based extension modules. • HDCP pass-through • Compact Sender and Receiver modules provide a clean, or panels. Their compact • Supports Deep Color easy installation The for pigtail Sender and Receiver modules relieves stress ind equipment a design of•theFCC • Compact Sender and Receiver modules provide a clean, and CE compliant for EMI/RFI emission and clutter on the source and display connector panels. Their compact easy installation asily extend HDMI. design makes them ideal for fitting neatly behind equipment for a • FCC and CE compliant for EMI/RFI emission Specifications* clean installation, making it a great way to easily extend HDMI. Specifications* How It Works • Maximum Pixel Clock: 225 MHz ource. The Receiver • Video Input Connector (Sender): (1) HDMI-19-pin, male • Maximum Pixel Clock: 225 MHz nect a single-strand • Video Output Connector (Receiver): (1) HDMI 19-pin, male The Sender pigtail end plugs into the HDMI source. The Receiver • Video Input fiber optic cable from Link Connector (1) Type SC fiber (50 /125µm) Connector (Sender): (1) HDMI-19-pin, male end plugs into• the HDTV display.(Sender/Receiver): Connect a single-strand • Video Output Connector (Receiver): (1) HDMI 19-pin, male power supplypigtail into the • Power (Receiver): 5Voptic DC cable from (OM2)Supply SC-terminated fiber •applications) Link Connector (Sender/Receiver): (1) Type SC fiber (50 /125µm) will appear50/125µm on your multimode • Power Supply (Sender): 5V DC (not needed for most the Sender to the Receiver module. Plug the power supply into the • Power Supply (Receiver): 5V DC (max.) Receiver module and• aPower vibrantConsumption Hi-Def picture(Receiver): will appear1.5W on your • Power Supply (Sender): 5V DC (not needed for most applications) • Operating Temperature: 0° to +50° C display. • Power Consumption (Receiver): 1.5W (max.) • Storage Temperature: -20° to +70° C • Operating Temperature: 0° to +50° C be powered externally • Relative Humidity: 10% to 80% • Storage Temperature: -20° to +70° C wer through the HDMI • Dimensions (W x H x D): 1.18" x 0.47" x 10.71" Note: The Sender module does not need to be powered externally • Relative Humidity: 10% to 80% 11.93mm x 272.03mm) unless the source does (29.97mm not supply xenough power through the HDMI • Dimensions (W x H x D): 1.18" x 0.47" x 10.71" • Shipping Weight: 1lb (0.45 kg) connector. (29.97mm x 11.93mm x 272.03mm) • Shipping Weight: 1lb (0.45 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com ® 1080P Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 notice. www.gefen.com All features and specifications subject to change without All trademarks are the property of their respective owners. *All features and specifications subject to change without notice. All trademarks are the property of their respective owners. ® 1080P Small Fiber Optic Pigtail Module Extends DVI up to 1000 feet EXT-DVI-CP-FM10 Pigtail module DVI extension using a singlestrand multimode fiber optic cable with HDCP support. The DVI fiber optic pigtail module extender with HDCP support extends DVI up to 1000 feet (300 meters) using single-strand 50/125µm multimode (OM2) SC-terminated fiber optic cable to a supporting display at 1920 x1200 WUXGA resolution. Optical signal transmission provides galvanic isolation and immunity to electromagnetic interference compared to similar copper based extension modules. The pigtail design of the Sender and Receiver modules relieves stress and clutter on the source and display connector panels. Their compact design makes them ideal for fitting neatly behind equipment for a clean installation, making it a great way to easily extend DVI. How It Works The Sender pigtail end plugs into the DVI source. The Receiver pigtail end plugs into the display. Connect a single-strand 50/125µm multimode (OM2) SC-terminated fiber optic cable from the Sender module to the Receiver module and a vibrant Hi-Def picture will appear on your display. Note: The Sender module does not need to be externally powered unless the source does not supply enough power through the DVI connector. Features* • Extends DVI up to 1000 feet (300 meters) using a single-strand 50/125µm multimode (OM2) SC-terminated fiber optic cable • Supports resolutions up to 1920 x 1200 (WUXGA) • Fiber optic transmission eliminates electromagnetic interference (EMI) • Pigtail design relieves stress and clutter on the source and display connector panels • DDC bidrectional support • HDCP pass-through • Compact Sender and Receiver modules provide a clean, easy installation • FCC and CE compliant for EMI/RFI emission Specifications* • • • • • • • • • • • Maximum Pixel Clock: 165 MHz Video Input Connector (Sender): (1) DVI-D 18-pin, male Video Output Connector (Receiver): (1) DVI-D 18-pin, male Link Connector (Sender/Receiver): (1) Type SC fiber (50 /125µm) Power Supply (Receiver): 5V DC Power Supply (Sender): 5V DC (not needed for most applications) Power Consumption (Receiver): 1.5W (max.) Operating Temperature: 0° to +50° C Storage Temperature: -20° to +70° C Relative Humidity: 10% to 80% Dimensions (W x H x D): 1.54" x 0.63" x 11.49" (39.11mm x 16mm x 291.84mm) • Shipping Weight: 1lb. (0.45 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com *All features and specifications subject to change without notice. All trademarks are the property of their respective owners. www.gefen.com(800)545-6900 Module Extends DVI up to 3300 feet EXT-DVI-FM15 Modular DVI extension using a single-strand multimode fiber optic cable with Virtual EDID. Features* The attractive and compact Sender and Receiver modules fit neatly behind the equipment for a clean installation, making it a great way to extend DVI. • Extends DVI up to 3300 feet (1 km) over a single-strand of OM3 (laser-optimized 50/125µm) multimode fiber optic cable • Extends DVI up to 1650 feet (500 m) over a single-strand of OM2 (conventional 50/125µm) multimode fiber optic cable • Extends DVI up to 1000 feet (300 m) over a single-strand of OM1 (62.5/125µm) multimode fiber optic cable • Supports resolutions up to 1920 x 1200 (WUXGA) • Virtual EDID allows EDID copying from the display to the source • Fiber optic transmission eliminates electromagnetic interference (EMI) • Sturdy metal die-cast enclosures are perfect for professional and industrial applications • Compact Sender and Receiver modules provide a clean, easy installation • Use Gefen CAB-1SC-xxxx OM1 Fiber Optic Link Cables for distances from 30 - 330 feet (9-100 meters) • FCC and CE compliant for EMI/RFI emission How It Works Specifications* The Sender module plugs into the DVI source. The Receiver module plugs into the display. Connect a single-strand multimode SC-terminated fiber optic cable from the Sender to the Receiver module. Plug the power supply into the Receiver module and a vibrant Hi-Def picture will appear on your display. • • • • • • • • • • • The DVI fiber optic module extender with Virtual EDID extends DVI up to 3300 feet (1 km) to a display supporting resolutions up to 1920 x 1200 (WUXGA) using a single-strand 50/125µm laseroptimized multimode (OM3) SC-terminated fiber optic cable. Optical signal transmission provides galvanic isolation and immunity to electromagnetic interference compared to similar copper-based extension modules. The Virtual EDID feature programs the display EDID into the Sender module to ensure fast integration and compatibility between the source and the display. Note: The Sender module does not need to be powered externally unless the source does not supply enough power through the DVI connector. Maximum Pixel Clock: 165 MHz Video Input Connector (Sender): DVI-D, 19-pin, male Video Output Connector (Receiver): DVI-D, 19-pin, male Link Connector (Sender / Receiver): (1) Type SC fiber (50/125µm) Power Supply: (Receiver): 5V DC Power Supply (Sender): 5V DC (not needed for most applications) Power Consumption (Receiver): 0.95 W (max.) Operating Temperature: 0° to +50° C Storage Temperature: -30° to +70° C Relative Humidity: 5% to 85% Dimensions (W x H x D): 1.96" x 0.59" x 2.98" (49.78mm x 14.98mm x 75.69mm) • Shipping Weight: 2 lbs (0.91 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com *All features and specifications subject to change without notice. All trademarks are the property of their respective owners. Extend Dual-Link DVI on Two Displays up to 200 feet over CAT-6a EXT-2DVI-CAT6DL Extend Dual-Link DVI to two displays over four CAT-6a cables The 2x Dual Link DVI Extender over CAT-6a extends two dual-link DVI sources to two Hi-Def displays up to 200 feet (60 meters) away. Dual-link resolutions up to 3840 x 2400 are supported using four CAT-6a cables. Extending dual-link resolutions over standard DVI cables have a limitation of 15 feet. Exceeding this distance requires additional repeaters and/or boosters. The 2x Dual Link DVI Extender over CAT-6a provides a cost-effective easy-to-install solution. How It Works Place the 2X Dual Link DVI Extender over CAT-6a Sender unit next to the source. Use the included DVI cables to connect the DVI sources to the Sender unit. Connect the Receiver unit to the DVI displays using DVI cables. Connect the Sender unit to the Receiver unit using four CAT-6a cables up to 200 feet (60 meters) in length. Connect the included locking power supplies to the Sender and Receiver units and plug both power cords into available electrical outlets. Note: This product supports HDCP pass-through only when using single-link resolutions. Features* • Extends two dual-link DVI sources to two dual-link DVI displays up to 200 feet (60 meters) over four CAT-6a cables • Supports dual-link resolutions up to 3840 x 2400 • EDID management with Local and pass-through modes • EQ adjustment trim pots on Receiver equalize the signal to compensate for cable length and the quality/skew variances found among different CAT-6a cables • Locking Power Supplies • Rack mountable (rack ears included) Specifications* • Maximum Pixel Clock: 2 x 165 MHz • Input Video Signal: 1.2V p-p • Input DDC Signal: 5V p-p (TTL) • Video Input Connector (Sender): (2) DVI-I, 29-pin, female (digital only) • Video Output Connector (Receiver): (2) DVI-I, 29-pin, female (digital only) • Link Connectors (Sender / Receiver): (4) RJ-45 • Power Supply (Sender / Receiver): 5V DC, Locking • Power Consumption: 20W per unit (max.) • Operating Temperature: 0 - 40 °C • Dimensions: (W x H x D): 17.5" x 1.7" x 4.3" (435 mm x 45mm x110mm) • Shipping Weight: 9.5 lbs (4.32 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com(800)545-6900 Extend two Dual Link DVI Displays and USB EXT-2DVI-DLKVM-CAT6 Dual Link DVI KVM Extender over CAT-6 Features: The 2x Dual Link DVI KVM Extender over CAT-6 extends any two DVI and USB sources to a monitor, touch screen display, or other digital signage application over a distance up to 330 feet (100 meters) using four CAT-6a cables. USB 2.0 data rates up to 100 Mbps are supported in addition to backward compatibility with USB 1.1. The Receiver unit allows the connections of up to four USB devices, providing access to printers, scanners, cameras, external storage media, digital signage, and automated control systems. This product uses Gefen ELR technology, allowing DVI and USB signals to travel along four CAT-6a cables. • Supports DVI resolutions up to 1920x1200 or 1080p at 330 feet (100 meters) • Extends two DVI devices up to 330 feet (100 meters) • Extends four USB devices up to 330 feet (100 meters) • Supports USB 2.0 • Backward-compatible with USB 1.1 devices • Field Upgradeable via USB mini-jack • Works with PC and Mac computers • Locking Power Supplies • Wall-mountable How It Works Connect up to two DVI sources to the Sender unit using the supplied DVI cables. Use the supplied USB cables to connect the USB host (source) device to the USB port on the Sender Unit. Connect up to four USB devices to the Receiver unit. Connect the USB Link from the Sender to the Receiver Unit using a CnjhbhAT-6a cable. Connect up two two displays to the Receiver unit using the supplied DVI cables. Use four Cat-6 cables, up to 330 feet (100 meters), to connect the Sender unit to the Receiver unit. Connect the included locking power supplies to the Sender unit and Receiver unit and connect both power cords to available electrical outlets. Note: This product does not support HDCP content with DVI sources.ik Specifications*: • • • • • • • • • • • • Maximum Pixel Clock: 165 MHz Input Video Signal: 1.2V p-p Input DDC Signal: 5V p-p (TTL) DVI Connector (Sender / Receiver): (2) DVI-I 29-pin, female USB Connector (Sender): (1) Type B USB Connector (Receiver): (4) Type A USB Link Connector (Sender / Receiver): (2) RJ-45 (1 per unit) Link Connector ( Sender / Receiver): (4) RJ-45 (2 per unit) Power Supply (Sender / Receiver): 5V DC, Locking Operating Temperature: 0 - 40 °C Dimensions: 8.5" W x 1.75" H x 4.5" D Shipping Weight: 6 lbs. (preliminary) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com *Specifications subject to change without notice. All trademarks are the properties of their respective owners. Extend two DVI displays and USB over two CAT-5 cables up to 330 feet (100 meters) EXT-2DVIKVM-ELR Extra Long Range KVM Extender for two DVI sources and USB peripherals over two CAT-5 cables The 2x DVIKVM Extra Long Range Extender Over One CAT5 extends any two DVI sources and USB to two monitors, touch screen displays, or digital signage applications up to 330 feet (100 meters), using two CAT-5e cables. USB 2.0 data rates up to 100 Mbps are supported in addition to backwardcompatibility with USB 1.1. The Receiver unit allows the connections of up to three USB devices, providing access to printers, scanners, cameras, external storage media, digital signage, and automated control systems. This product uses Gefen ELR technology, allowing DVI and USB signals to travel along the same CAT-5e cables, reducing cabling costs and providing easier installation. Features* • • • • • • • • • • Extends DVI and USB up to 330 feet (100 meters) Supports resolutions up to 1920 x 1200 Supports 100 Mbps using USB 2.0 Backward-compatible with USB 1.1 devices Field-upgradeable via mini-USB service port Supports DDWG standard for DVI-compliant monitors Supports any Operating System (OS) EDID management for rapid integration of source and display devices HDBaseT Certified Rack-mountable Specifications* How It Works Place the 2x DVIKVM Extra Long Range Extender Sender unit next to the DVI sources. Use the included DVI cables to connect the DVI sources to the Sender unit. Use the supplied USB cable to connect the USB host (source) device to the USB port on the Sender unit. Connect the Receiver unit to the displays with DVI cables. Connect the USB devices to the Receiver unit. Use two CAT-5e cables, each up to 330 feet (100 meters), to connect the Sender to the Receiver unit. Connect the included locking power supplies to the Sender and Receiver units and plug both power cords into available electrical outlets. Note: This product does not support HDCP content with DVI sources. • • • • • • • • • • Maximum Pixel Clock: 165 MHz Video Input Connectors (Sender): (2) DVI-I 29-pin, female (digital only) Video Output Connectors (Receiver): (2) DVI-I 29-pin, female (digital only) USB Host Connector (Sender): (1) USB Type B, female USB Device Connectors (Receiver): (3) USB Type A, female Link Connectors (Sender/Receiver): (2) RJ-45, Shielded Service Connector for Field Upgrades: USB Mini-B, female Power Supply (Sender / Receiver): 5V DC, Locking Power Consumption (Sender / Receiver): 20W (max.) Dimensions (Sender / Receiver): 17.1” W x 4.2” D x 1.7” H (434mm x 107mm x 43mm) • Rack Space: 1U (rack ears included) • Shipping Weight: 9 lbs. (4 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com *Featiures and specifications subject to change without notice. www.gefen.com(800)545-6900 Extend DVI and RS-232 over One Fiber Optic cable EXT-DVIRS232-1FO Extends DVI and RS-232 over One Fiber Optic cable up to 1000 feet (300 meters) The Extender for DVI and RS232 over One Fiber Optic cable is a complete extension solution, allowing DVI and RS-232 to be extended to a monitor, touch-screen display, or other DVI device up to 1000 feet (300 meters) from the source. This extender is ideal when the DVI source is located in a machine room or closet and the display is located in an interference-prone environment, far away. A single strand of SC-terminated multi-mode fiber optic cable is used for extension, providing excellent protection from electromagnetic interference (EMI), preserving both DVI and RS-232 signal integrity. Locking DVI, RS-232, and power connectors ensure secure connections. Features: • • • • • • • • • Extends up to 1000 feet (300 meters) over 50/125µm (OM3) fiber Extends up to 330 feet (100 meters) over 62.5/125µm (OM1) fiber Extends DVI and RS-232 over a single fiber strand Supports resolutions up to 1080p Full HD and 1920 x 1200 EDID management for rapid integration of source and display Automatic calibration based on the type and length of fiber optic cable Fiber cable is immune to electromagnetic interference (EMI) Locking power supplies Works with Gefen CAB-1SC-XXXX 1 Strand SC-SC Multimode Fiber Optic Link (Available lengths: 30 - 330 feet) How It Works Specifications*: The Sender unit is placed near the DVI source and the Receiver unit near the Display. Connect the supplied DVI cable between the Sender unit and the DVI source. Connect a second DVI cable between the Receiver unit and the display. Connect the RS-232 cable from the RS-232 source to the Sender unit. Connect the RS-232 cable between the Receiver unit and the RS-232 connection on the display side. Connect one strand of multi-mode fiber optic cable, with SC connectors, between the Sender unit and the Receiver unit. Connect the locking power supplies to both the Sender and Receiver units, and plug into available AC outlets. • • • • • • • NOTE: When HDCP is required, full handshaking is guaranteed up to 1000 feet (300 meters). • • • • Maximum Pixel Clock: 165 MHz Input Video Signal: 1.2V p-p Input DDC Signal: 5V p-p (TTL) DVI Connectors (Sender/Receiver): (1) DVI-I, 29-pin, female (digital only) RS-232 Connector (Sender): (1) DB-9, female RS-232 Connector (Receiver): (1) DB-9, male Link Connectors (Sender/Receiver): SC-terminated (for 50/125µm or 62.5/125µm fiber) Operating Temp: 0° - 40° C Power Supply: 5V DC Dimensions (W x H x D): 5.0" x 1.25" x 3.4" (127mm x 32mm x 86mm) Shipping Weight: 4 lbs. (1.8 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com *Features an d specifications subject to change without notice. Modules Extend Dual-Link DVI up to 3300 feet EXT-DVI-FM2500 Modular Dual-Link DVI extension using a two-strand multimode fiber optic cable with Virtual EDID The Dual Link DVI fiber optic module extender with Virtual EDID extends dual-link DVI up to 3300 feet (1 km) to a display supporting resolutions up to 3840 x 2400 (WQXGA) using a two-strand 50/125µm laser-optimized multimode (OM3) SC-terminated fiber optic cable. Optical signal transmission provides galvanic isolation and immunity to electromagnetic interference compared to similar copper based extension modules. The Virtual EDID feature programs the display EDID into the Sender module to ensure fast integration and compatibility between the source and the display. The attractive and compact Sender and Receiver modules fit neatly behind the equipment for a clean installation, making it a great way to extend dual-link DVI. How It Works The Sender module plugs into the DVI source. The Receiver module plugs into the dual-link display. Connect a two-strand multimode SC-terminated fiber optic cable from the Sender to the Receiver module. Plug the power supply into the Receiver module and a vibrant Hi-Def picture will appear on your display. Note: The Sender module does not need to be powered externally unless the source does not supply enough power through the DVI connector. Features* • Extends dual-link DVI up to 3300 feet (1 km) over two strands of OM3 (laser-optimized 50/125µm) multimode fiber optic cable • Extends dual-link DVI up to 1650 feet (500 m) over two strands of OM2 (conventional 50/125µm) multimode fiber optic cable • Extends dual-link DVI up to 1000 feet (300 m) over two strands of OM1 (62.5/125µm) multimode fiber optic cable • Supports resolutions up to 3840 x 2400 (dual-link DVI) • Virtual EDID allows EDID copying from the display to the source • Fiber optic transmission eliminates electromagnetic interference (EMI) • Sturdy metal die-cast enclosures are perfect for professional and industrial applications • Compact Sender and Receiver modules provide a clean, easy installation • Use Gefen CAB-2SC-xxx OM1 Fiber Optic Link Cables for distances from 30 - 330 feet (9 - 100 meters) • FCC and CE compliant for EMI/RFI emission Specifications* • • • • • • • • • • • Maximum Pixel Clock: 2 x 165 MHz Video Input Connector (Sender): (1) DVI-D 19-pin, male Video Output Connector (Receiver): (1) DVI-D 19-pin, male Link Connector (Sender / Receiver): (1) Type SC fiber (50/125µm) Power Supply (Receiver): 5V DC Power Supply (Sender): 5V DC (not needed for most applications) Power Consumption (Receiver): 1.5W (max.) Operating Temperature: 0° to +50° C Storage Temperature: -30° to +70° C Relative Humidity: 5% to 85% Dimensions (W x H x D): 1.54" x 0.59" x 2.83" (39.11mm x 14.98mm x 71.88mm) • Shipping Weight: 2 lbs (0.91 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com *All features and specifications subject to change without notice. All trademarks are the property of their respective owners. www.gefen.com(800)545-6900 Extend DVI with USB 2.0, Audio, and RS-232 up to 6,600 feet EXT-DVI-3600HD Extend DVI, USB 2.0, RS-232 and Analog Audio up to 6,600 feet (2000 meters) The DVI 3600HD allows you to operate a single DVI-compliant computer from two workstations, by extending DVI, USB 2.0, analog audio, and RS-232 from the computer to the remote workstation. USB peripherals can be placed at either of the two locations, by the Sender or Receiver unit. How It Works The DVI 3600HD consists of a Sender and a Receiver unit. The Sender unit connects to the computer's DVI-compliant video card output, analog audio jack, RS-232 port, and USB 2.0 port. The DVI 3600HD Receiver unit connects to the remote display and peripherals. Four strands of LC fiber optic cable connect the Sender and Receiver units together. The DVI 3600HD has two modes of USB operation. When in local mode, the computer sees USB devices connected to the Sender unit. When in remote mode, the computer sees USB devices connected to the Receiver unit. These two modes are configured using a switch on the front panel of the Sender unit. Note: Extension distance will depend on the type of fiber media used: • • Single-mode fiber: WUXGA (1920 x 1200) resolution @ 6,600 ft. (2000 meters) Multi-mode fiber: WUXGA (1920 x 1200) resolution @ 1,650 ft. (500 meters) Features* • • • • • • • • Extends DVI, USB2.0, RS-232, and analog audio up to 6,600 feet (2000 meters) with single-mode fiber, and up to 1,650 feet (500 meters) with multi-mode fiber Supports video resolutions up to 1920 x 1200 Uses four-strand single-mode or multi-mode LC-terminated fiber cables Supports Virtual DDC1 and DDC2B protocols Supports Local and Virtual EDIDs Supports USB 2.0 and USB 1.1 Configurable to allow access of USB devices located at Sender Side or Receiver Side Rack-mountable (rack ears included) Specifications* • • • • • • • • • • • • • • • • • Maximum Pixel Clock: 165MHz Video Input Connector (Sender): (1) DVI-D (24 pin), female (digital only) Video Monitor Output Connector (Sender): (1) DVI-D (24 pin), female (digital only) Audio Input Connector (Sender) (1) 3.5 mm mini-stereo jack Audio Output Connector (Receiver) (1) 3.5 mm mini-stereo jack USB Host Connector (Sender): (1) USB Type B USB Local Device Connectors (Sender): (2) USB Type A, female USB Device Connectors (Receiver): (4) USB Type A, female RS-232 Port (Sender): (1) DB-9, female RS-232 Port (Receiver): (1) DB-9, male Link Connectors (Sender / Receiver): (4) Type LC fiber connectors (2 x LC Duplex) Fiber Cable: CAB-LC-XXX (62.5µ multi-mode) Console Connector (Sender / Receiver): (1) RJ-45 jack (for future use) Power Supply (Sender / Receiver): 2 x 12V DC Power Consumption: 36W (max.) each Dimensions (Sender / Receiver)(W x H x D): 12.4” x 1.6” x 5” (315mm x 40mm x 127mm) Shipping Weight: 8 lbs. (3.6 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com *Features and specifications subject to change without notice. All trademarks and registered trademarks are properties of their respective owners Extend 3G-SDI Over One Single-Mode Fiber Optic Cable up to 1.25 miles EXT-3GSDI-FOSM 3G-SDI extension using a single-mode fiber optic cable The 3GSDI Fiber Optic Extender extends 3G-SDI over one single-mode ST-terminated fiber optic cable up to 1.25 miles (2 km). It supports SMPTE-424M (3G-SDI), SMPTE-292M (HD-SDI), and SMPTE-259M (SDl). The 3G-SDI BNC connector and the ST-terminated fiber optic signal transmission provide excellent immunity to electromagnetic interference compared to copper based extension modules. The compact design makes the small modules ideal for fitting neatly behind equipment for a clean installation, and a great way to easily extend any SDI signal. How It Works Features* • Supports SMPTE-424M (3G-SDI), SMPTE-292M (HD-SDI), and SMPTE-259M (SDl) specifications • Extends 3G-SDI up to 1.25 miles (2 km) over one single-mode ST-terminated fiber optic cable • Locking power connectors • Robust metal die-cast enclosure for reliable operation in harsh environment • Fiber optic transmission eliminates electromagnetic interference (EMI) • Compact Sender and Receiver modules provide a clean, easy installation • FCC and CE compliant for EMI/RFI emission Specifications* The Sender module plugs into the BNC connector on the SDI source. The Receiver module plugs into the BNC input of the SDI device up to 1.25 miles (2 km) away. Connect one single-mode ST-terminated fiber optic cable from the Sender to the Receiver module. Plug the power connectors from the two power supplies into the locking connectors on the Sender and Receiver modules. • • • • • • • • • • • • • • Input Impedance: 75 Ohm Data Rate: up to 3 Gbps Signal Level: 800mVp-p +/- 50mV Optical Fiber Type: ST (single-mode) Number of Fibers: 1 SDI Connector: BNC Male Range: Up to 1.25 miles (2 km) Propagation Delay (Sender): 1.5 ns Propagation Delay (Receiver): 40 ns Power Supply: (2) 5V DC Power Budget: 12dB Operating Temperature: -20 to + 70C Relative Humidity: 0 to 95% Wavelength (Sender unit): 1290 nm (min), 1310 nm (typical), 1330 nm (max) • Wavelength (Receiver unit): 1100 nm (min), 1310 nm (typical), 1650 nm (max) • Dimensions (W x H x D): 0.77" x 0.77" x 1.97" (19.55mm x 19.55mm x 50.03 mm) • Shipping Weight: 1.3 lbs (0.58 kg) Gefen, LLC 20600 Nordhoff Street, Chatsworth CA 91311 Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 www.gefen.com *All features and specifications subject to change without notice. All trademarks are property of their respective owners. www.gefen.com(800)545-6900 NAB Supplemental Catalog 2012
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement