901 - 1351 Troubleshooting Guide

901 - 1351 Troubleshooting Guide
MULTIFUNCTIONAL DIGITAL SYSTEMS
Operator's Manual
Troubleshooting
Introduction
This manual contains detailed instructions and notes on the operation and use of this machine. For your
safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy
place for quick reference.
Do not copy or print any item for which reproduction is prohibited by law.
Copying or printing the following items is generally prohibited by local law:
bank notes, revenue stamps, bonds, stock certificates, bank drafts, checks, passports, driver's licenses.
The preceding list is meant as a guide only and is not inclusive. We assume no responsibility for its
completeness or accuracy. If you have any questions concerning the legality of copying or printing certain items, consult with your legal advisor.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.
Notes:
Some illustrations in this manual might be slightly different from the machine.
Depending on which country you are in, certain units may be optional. For details, please contact your
local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the inch version.
For good copy quality, the supplier recommends that you use genuine toner from the supplier.
The supplier shall not be responsible for any damage or expense that might result from the use of parts
other than genuine parts from the supplier with your office products.
Power Source
208-240 V, 50/60 Hz, 20 A or more.
Please be sure to connect the power cord to a power source as shown above. For details about power
source, see p.105 “Power Connection”.
Trademarks
Microsoft®, Windows® and Windows NT® are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
TrueType is registered trademarks of Apple Computer, Inc.
PostScript® and Acrobat® are registered trademarks of Adobe Systems, Incorporated.
PCL is a registered trademark of Hewlett-Packard Company.
Other product names used herein are for identification purposes only and might be trademarks of their
respective companies. We disclaim any and all rights to those marks.
The proper names of the Windows operating systems are as follows:
• The product name of Windows® 95 is Microsoft® Windows 95.
• The product name of Windows® 98 is Microsoft® Windows 98.
• The product name of Windows® Me is Microsoft® Windows Millennium Edition (Windows Me).
• The product names of Windows® 2000 are as follows:
Microsoft® Windows® 2000 Advanced Server
Microsoft® Windows® 2000 Server
Microsoft® Windows® 2000 Professional
• The product names of Windows® XP are as follows:
Microsoft® Windows® XP Professional
Microsoft® Windows® XP Home Edition
• The product names of Windows ServerTM 2003 are as follows:
Microsoft® Windows ServerTM 2003 Standard Edition
Microsoft® Windows ServerTM 2003 Enterprise Edition
Microsoft® Windows ServerTM 2003 Web Edition
• The product names of Windows NT® 4.0 are as follows:
Microsoft® Windows NT® Server 4.0
Microsoft® Windows NT® Workstation 4.0
Manuals for This Machine
Refer to the manuals that are relevant to what you want to do with the machine.
❖ About This Machine
Be sure to read the Safety Information in this manual before using the machine.
This manual provides an introduction to the functions of the machine. It also
explains the control panel, preparation procedures for using the machine,
how to enter text, and how to install the CD-ROMs provided.
❖ General Settings Guide
Explains User Tools settings, and Address Book procedures such as registering e-mail addresses, and user codes. Also refer to this manual for explanations on how to connect the machine.
❖ Troubleshooting
Provides a guide to solving common problems, and explains how to replace
paper, toner, staples, and other consumables.
❖ Security Reference
This manual is for administrators of the machine. It explains security functions that the administrators can use to protect data from being tampered, or
prevent the machine from unauthorized use.
Also refer to this manual for the procedures for registering administrators, as
well as setting user and administrator authentication.
❖ Copy/ Document Server Reference
Explains Copier and Document Server functions and operations. Also refer to
this manual for explanations on how to place originals.
❖ Printer Reference
Explains Printer functions and operations.
❖ Scanner Reference
Explains Scanner functions and operations.
❖ Network Guide
Explains how to configure and operate the machine in a network environment, and use the software provided.
This manual covers all models, and includes descriptions of functions and
settings that might not be available on this machine. Images, illustrations, and
information about operating systems that are supported might also differ
slightly from those of this machine.
❖ Other manuals
• PostScript3 Supplement
• Manuals for DeskTopBinder Lite
i
Note
❒ Manuals provided are specific to machine types.
❒ Adobe Acrobat Reader/Adobe Reader must be installed in order to view the
manuals as PDF files.
❒ “PostScript3 Supplement” includes descriptions of functions and settings
that might not be available on this machine.
ii
TABLE OF CONTENTS
Manuals for This Machine ......................................................................................i
How to Read This Manual .....................................................................................1
Symbols .....................................................................................................................1
Names of Major Items ................................................................................................2
1. When the Machine Does Not Operate As Wanted
Indicators................................................................................................................3
Panel Tone..............................................................................................................4
Checking Machine Status and Settings...............................................................5
When an Indicator to the Left of a Function Key is Lit.......................................8
When You Have Problems Operating the Machine.............................................9
When a Job is Not Performed.............................................................................14
2. Troubleshooting When Using the Copy Function
When a Message Appears...................................................................................17
Display During Connect Copy ............................................................................22
If Connect Copy is Cancelled .............................................................................23
If You Cannot Exit from Connect Copy..............................................................24
When You Cannot Make Clear Copies ...............................................................25
When You Cannot Make Copies As Wanted .....................................................27
When Memory is Full ...............................................................................................30
3. Troubleshooting When Using the Printer Function
When a Message Appears during Installation of the Printer Driver................31
Windows 95/98/Me...................................................................................................31
Windows 2000..........................................................................................................32
Windows XP, Windows Server 2003........................................................................32
Windows NT 4.0.......................................................................................................33
If USB Connection Fails ......................................................................................34
When a Message Appears...................................................................................35
Status Messages...................................................................................................... 35
Alert Messages ........................................................................................................36
Checking the Error Log ............................................................................................37
When You Cannot Print.......................................................................................38
Other Printing Problems .....................................................................................40
4. Troubleshooting When Using the Scanner Function
When Scanning is Not Done as Expected .........................................................45
When You Cannot Send Scanned Files .............................................................46
When Stored Files Cannot be Accessed .................................................................46
When You Cannot Browse the Network to Send a Scan file ................................... 46
When the TWAIN Driver Cannot be Started ............................................................ 46
When Stored Files Cannot be Edited.......................................................................47
Operations are not possible when messages appear .............................................. 47
iii
When a Message is Displayed ............................................................................48
When a Message is Displayed on the Control Panel ...............................................48
When a Message is Displayed on the Client Computer...........................................54
5. Adding paper, Toner and Staples
Loading paper ...................................................................................................... 59
Loading paper into Tray 1 (Tandem Tray) ............................................................... 59
Loading Paper into the A3/11” × 17” Tray Unit.........................................................61
Loading Paper into Tray 2 and 3..............................................................................62
Loading Paper into the Large Capacity Tray (LCT) ................................................. 63
Loading Paper into the Wide Large Capacity Tray (Wide LCT) ...............................64
Loading Paper into the Multi Bypass Tray (Tray 7)..................................................65
Loading Paper in the Interposer...............................................................................67
Changing the Paper Size.....................................................................................70
Changing the Paper Size in Tray 2 and 3 ................................................................70
Changing the Paper Size in the Large Capacity Tray (Tray 4 and 5) ......................72
Changing the Paper Size in the Wide Large Capacity Tray.....................................76
Changing to a Size that is Not Automatically Detected............................................78
Pausing Copy When Using Finisher ..................................................................81
Adding Toner........................................................................................................82
Inserting Toner ......................................................................................................... 84
Used Toner ..............................................................................................................84
Adding Staples.....................................................................................................85
Finisher .................................................................................................................... 85
Booklet Finisher (Saddle Stitch)...............................................................................86
6. Clearing Misfeeds
Removing Jammed Paper ...................................................................................87
Locating Jammed Paper ..........................................................................................88
Removing Jammed Paper........................................................................................ 90
When Z-folded paper is not properly aligned ...........................................................99
Removing Jammed Staples .............................................................................. 100
Finisher .................................................................................................................. 100
Booklet Finisher (Saddle Stitch).............................................................................101
Removing Punch and Staple Waste.................................................................102
Finisher .................................................................................................................. 102
7. Remarks
Where to Put Your Machine .............................................................................. 103
Machine Environment ............................................................................................103
Moving....................................................................................................................104
Power Connection..................................................................................................105
Access to the Machine ...........................................................................................106
Maintaining Your Machine ................................................................................107
Cleaning the Exposure Glass.................................................................................107
Cleaning the Auto Document Feeder.....................................................................108
Earth Leakage Circuit Breaker..........................................................................109
INDEX....................................................................................................... 111
iv
How to Read This Manual
Symbols
This manual uses the following symbols:
Indicates important safety notes.
Ignoring these notes could result in serious injury or death. Be sure to read these
notes. They can be found in the “Safety Information” section of About This Machine.
Indicates important safety notes.
Ignoring these notes could result in moderate or minor injury, or damage to the
machine or to property. Be sure to read these notes. They can be found in the
“Safety Information” section of About This Machine.
Indicates points to pay attention to when using the machine, and explanations
of likely causes of paper misfeeds, damage to originals, or loss of data. Be sure
to read these explanations.
Indicates supplementary explanations of the machine’s functions, and instructions on resolving user errors.
This symbol is located at the end of sections. It indicates where you can find further relevant information.
[]
Indicates the names of keys that appear on the machine’s display panel.
{}
Indicates the names of keys on the machine’s control panel.
1
Names of Major Items
Major items of this machine are referred to as follows in this manual:
• Auto Document Feeder → ADF
• Finisher SR5000 → Finisher
• Booklet Finisher BK5000 → Booklet Finisher
2
1. When the Machine Does
Not Operate As Wanted
This chapter explains basic troubleshooting procedures that are applicable to all
functions of this machine.
Indicators
This section explains Indicators displayed when the machine requires the user
to remove misfed paper, add paper, or perform other procedures.
x: Misfeed indicator
Appears when a misfeed occurs.
See p.87 “Removing Jammed Paper”.
B: Add Paper indicator
Appears when paper-out condition occurs.
See p.59 “Loading paper”.
D: Add Toner indicator
Appears when toner runs out.
See p.82 “Adding Toner”.
d: Add Staple indicator
Appears when staples run out.
See p.85 “Adding Staples”.
y: Empty Hole Punch Receptacle
indicator
Appears when the hole punch receptacle is full.
See p.102 “Removing Punch and Staple Waste”
0: Empty Waste Staple Receptacle
indicator
Appears when the waste staple receptacle is full.
L: Service Call indicator
Appears when the machine is mulfuncitoning, or needs
repairing.
M: Open Cover indicator
Appears when the front cover, etc, is open.
See p.102 “Removing Punch and Staple Waste”
3
When the Machine Does Not Operate As Wanted
Panel Tone
The following table explains the meaning of the various beep patterns that the
machine produces to alert users about left originals and other machine conditions.
1
Beep pattern
Meaning
Cause
Two long beeps.
Machine has warmed up. After cooling or being switched on, the
machine has fully warmed up and is
ready for use.
Single short beep.
Panel/screen input accepted.
A control panel or screen key was
pressed. Single short beeps are produced only when valid keys are
pressed.
Single long beep.
Job completed.
A Copier/Document Server Features
job has finished.
Four long beeps.
Soft alert.
The screen changes back to the initial
screen after the machine shifts to energy-saving mode, or the setting was reset at the simplified display.
Four long beeps repeated
five times.
Soft alert.
An original has been left on the exposure glass, paper is empty, or the punch
waste box is full.
Five short beeps repeated
five time.
Strong alert.
The machine requires user attention because paper have jammed, the toner
needs replenishing, or other troubles
have occurred.
Note
❒ Users cannot mute the machine's beep alerts. When the machine beeps to alert
users of a paper jam or toner request, if the machine's covers are opened and
closed repeatedly within a short space of time, the beep alert might continue,
even after normal status has resumed.
Reference
For details about enabling or disabling beep alerts, see “The System Settings”,
General Settings Guide.
4
Checking Machine Status and Settings
Checking Machine Status and Settings
You can check the machine's system status.
1
❖ Maintenance Info
You can check the following items under [Maintenance Info]:
• [Remaining Toner]
Displays the amount of remaining toner.
• [No Staples]
Displays where the staple is empty.
• [Punch Receptacle Full]
Displays whether the hole punch receptacle is full.
• [Waste Staple Receptcl Full]
Displays whether the waste staple receptacle is full.
• [Paper Tray]
Displays the paper type and size loaded in the paper tray.
• [Output Tray Full]
Displays whether the output tray is overloaded.
• [Original Misfeed]
Displays state of and solutions for original misfeeds.
• [Paper Misfeed]
Displays state of and solutions for paper jams.
• [Cover Open]
Indicates whether front cover, duplex unit, etc, is open.
❖ Data Storage
You can check the following items under [Data Storage]:
• [HDD Remaining Memory]
Displays the amount of available hard disk drive memory.
• [HDD File(s)]
Displays the total number of jobs stored in the hard disk drive.
• [Print Job(s)]
Displays the number of jobs for Hold print/Saved print/Locked
print/Sample print.
• [Memory Erase Status]
Displays the state of the memory data.
❖ Machine Address Info
You can check the following items under [Machine Address Info]:
• [Machine IPv4 Address]
Displays the machine's IPv4 address.
• [Machine IPv6 Address]
Displays the machine's IPv6 address.
5
When the Machine Does Not Operate As Wanted
❖ Inquiry
You can check the following items under [Inquiry]:
• [Machine Repairs]
Displays the machine number and contact number that are required for
service.
• [Sales Representative]
Displays the sales representative's telephone number.
• [Supply Order]
Displays the contact number for placing supply orders.
• [Supply Details]
Displays the name of toner, staples, etc, used on the machine.
1
A On the control panel, press [System Status] on the control panel.
B Press each tab and check the contents.
C After checking the information, press [Exit]. The previous screen returns.
6
Checking Machine Status and Settings
Note
❒ [Output Tray Full], [Original Misfeed], [Paper Misfeed], and [Cover Open] appear
only when these errors occur.
❒ For details about how to locate and remove misfeeds, see “Checking
Jammed Paper” or “Removing Jammed Paper”.
1
Reference
p.88 “Locating Jammed Paper”.
p.87 “Removing Jammed Paper”.
7
When the Machine Does Not Operate As Wanted
When an Indicator to the Left of a Function
Key is Lit
1
When an indicator to the left of a function key lights up, press the corresponding
function key. Then, follow the instructions displayed on the control panel.
Problem
Cause
Solution
Documents and reports
do not print out.
The paper output tray is
full.
Remove the paper from the tray.
Documents and reports
do not print out.
There is no copy paper
left.
Add more paper. See p.59 “Loading paper”.
An error has occurred.
The function whose indicator is lit is defective.
Record the code number shown in the
display and contact your service representative. See “When a Message displayed” of each chapter.
You can use other functions normally.
The machine is unable to
connect to the network.
A network error has occurred.
• Check the displayed message and
take an appropriate action. See
“When a Message displayed” of
each chapter.
• Check that the machine is correctly
connected to the network, and that
the machine is correctly set. See
“Network Settings”, General Settings Guide.
• Contact the administrator.
• When the function key is still lit,
even if you take the measures
above, contact your service representative.
Note
❒ If an error occurs in the function you are using, check the message that appears on the control panel, and then refer to “When a Message is Displayed”
for the relevant function.
Reference
p.17 “Troubleshooting When Using the Copy Function”.
p.31 “Troubleshooting When Using the Printer Function”.
p.45 “Troubleshooting When Using the Scanner Function”.
8
When You Have Problems Operating the Machine
When You Have Problems Operating the
Machine
1
The following chart gives explanations of common problems and messages.
If other messages appear, follow the instructions displayed.
Important
❒ Check the contact address and Serial No. of Machine shown in the call service
message, and then contact your service representative.
Problem
Cause
Solution
Although the copier
Functions other than the
screen appears when the copier function are not
machine is turned on us- yet ready.
ing the main power
switch, it cannot be
switched to another
screen by pressing the
{Printer} or {Scanner} key.
Wait a little longer.
The machine has just
been turned on and the
User Tools screen is displayed, but the User
Tools menu has items
missing.
Functions other than the
copier function are not
yet ready. Time required
varies by function. Functions appear in the User
Tools menu when they
become ready for use.
Wait a little longer.
The main power indicator continues blinking
and does not turn off
when pressed.
This occurs in the follow- Close ADF, and check if the machine is
ing cases:
communicating with a computer.
• ADF is open.
• The machine is communicating with external equipment.
• The hard disk is active.
The display is off.
The machine is in Energy
Saver mode.
Press the {Energy Saver} key to cancel
Energy Saver Mode. mode.
The display is off.
The operation switch is
turned off.
Turn on the operation switch.
Nothing happens when
the operation switch is
turned on.
The main power switch is
turned off.
Turn on the main power switch.
“Please wait.” appears.
This message appears
Wait for the machine to get ready.
when you turn on the operation switch.
“Please wait.” appears.
This message appears
Wait for the machine to get ready.
when you change the toner bottle.
9
When the Machine Does Not Operate As Wanted
Problem
“Memory is full.
Do you want to
store scanned
file?” appears.
1
Cause
Solution
The scanned originals ex- • Press [Store File] to store pages that
ceed the number of
have been scanned. Delete unnecessheets/pages that can be
sary files with [Delete File].
stored in the hard disk.
• Press [No] if you are not storing pages that have been scanned. Delete
unnecessary files with [Delete File].
“Self checking...” appears.
The machine is perform- The machine may perform periodic
ing image adjustment op- maintenance during operations. The
erations.
frequency and duration of maintenance
depends on the humidity, temperature,
and printing factors such as number of
prints, paper size, and paper type. Wait
for the machine to get ready.
The user code entry
screen is displayed.
Users are restricted by
user management.
Enter the user code (up to eight digits),
and then press [OK].
The Authentication
screen appears.
Basic Authentication,
Windows Authentication, LDAP Authentication or Integration Server
Authentication is set.
Enter your login user name and user
password. See “When the Authentication Screen is Displayed”, About This
Machine.
“You do not have
The use of the function is
restricted to authenticated users only.
Contact the administrator.
This user code is not allowed to use the function
selected.
Press the {Energy Saver} key. Confirm
that the display goes off, and then press
the {Energy Saver} key again. The display will return to the user code entry
display. When printing under the copier or printer function, press the {Energy
Saver} key only after printing has finished.
• When a misfeed message appears, it remains until you open
and close the cover as
required.
Clear misfed paper, and then open and
close the front cover. see p.87 “Clearing
Misfeeds”.
the privileges to
use this function.” is displayed.
“You do not have
the privileges to
use this function.” continues to be
displayed even though
you have entered a valid
user code.
An error message remains, even if misfed paper is removed.
• Paper is still jammed
in the tray.
Original images are
printed on the reverse
side of the paper.
You may have loaded the
paper incorrectly.
Misfeeds occur frequently. The tray's side fences
may not be locked.
Load paper correctly. Place paper in the
paper tray with the print side up. Load
paper into the bypass tray with the
print side down. See p.68 “OrientationFixed Paper or Two-Sided Paper”.
• Remove the paper. See p.87 “Removing Jammed Paper”.
• Check the side fences are locked.
See p.70 “Changing the Paper Size”.
10
When You Have Problems Operating the Machine
Problem
Cause
Misfeeds occur frequently. The tray's end fence may
not be set properly.
Solution
• Remove the paper. See p.87 “Removing Jammed Paper”.
• Check the end fence is set properly.
See p.70 “Changing the Paper Size”.
Misfeeds occur frequently. Paper of undetectable
size has been loaded.
1
• Remove the paper. See p.87 “Removing Jammed Paper”.
• When loading the paper of undetectable size, specify the paper size
in “Tray Paper Size”. See “Paper
Size: Tray 1-7”, General Settings
Guide and “Copy Paper”, About
This Machine.
Misfeeds occur frequently. There is a foreign object
on the finisher tray.
• Remove the paper. See p.87 “Removing Jammed Paper”.
• Do not place anything on the finisher tray. It may cause a paper jam.
Misfeeds occur frequently. The staple cartridge is not
set correctly.
The Booklet Finisher requires the saddle stitch stapler cartridge also. See p.85
“Adding Staples”.
Cannot print in duplex
mode.
[1 Sided Copy] is selected
for Paper Type: Tray 1-7.
Select [2 Sided Copy] for Paper Type:
Tray 1-7 See “Paper Size: Tray 1-7”,
General Settings Guide.
Cannot print in duplex
mode.
You cannot select duplex
printing if the paper type
is set to [OHP], [Tab Stock],
[Translucent] or [Label Paper].
Select a paper type that allows duplex
printing. See “Paper Size: Tray 1-7”,
General Settings Guide.
Authentication failed.
The entered login user
name or login password
is not correct.
Inquire the user administrator for the
correct login user name and login password.
Authentication failed.
The machine cannot perform authentication.
Contact the administrator.
The selected file(s) contained file(s) without access privileges. Only
file(s) with access privileges will be deleted.
You have tried to delete
files without the authority to do so.
Files can be deleted by the person who
created the file. To delete a file which
you are not authorized to delete, contact the person who created the file.
11
When the Machine Does Not Operate As Wanted
❖ Document Server
Problem
Cause
Solution
The number of scanned
pages exceeds the capacity per file of the Document Server.
To store scanned pages as a file, press
[Store File]. Scanned data is stored as a
file in the Document Server. If you do
not want to store scanned pages, press
[No]. Scanned data is deleted.
You forgot your password.
You cannot access a protected file without entering the password.
Contact the administrator.
You cannot find out what
is stored in a file.
You may not be able to
ascertain the contents of a
file simply from the file
name.
You can switch the Select File screen between [List] and [Thumbnail] display to
check the contents of the file. In list display, the file name, date and time of
storage, and user name are shown. In
thumbnail display, an image of the
stored file appears. You can enlarge the
image by pressing [Preview]. Use the Select File screen to check information
other than the file name. See “Checking
the Details of a Stored Document”,
Copy/Document Server Reference.
Memory frequently becomes full.
The document server
memory is full.
Delete unnecessary files. On the file selection display, select unnecessary files,
and then press [Delete File]. If this does
not increase available memory, do the
following.
“Exceeded max.
number of pages
per file. Do you
want to store the
scanned pages as
1 file?” appears.
1
To delete the files stored in the document server, select [Delete All Files in Document Server]. As this will permanently
delete every single file, make sure the
document server does not contain any
files you want to keep. See “Delete All
Files in Document Server”, General Settings Guide.
• Switch to the scanner screen, and
then delete unnecessary files stored
under the scanner function.
• Switch to the printer screen, and
then delete unnecessary files stored
under Sample Print, Locked Print,
Hold Print, or Stored Print.
You want to check print
quality before making a
large print run.
12
You can print a single
copy without specifying
the setting again.
Check print quality by printing out
only the first set using the {Sample
Copy} key.
When You Have Problems Operating the Machine
Problem
“Original is be-
ing scanned by
another function.
Please wait.” ap-
Cause
Copier or Scanner function is in use.
preview of this
page.” appears, and
To cancel a job in progress, first press
[Exit], and then press the {Copy} key or
{Scanner} key. Next, press the {Stop}
key. When the message “The Stop
1
key was pressed. Stop copying appears?” press [Stop].
pears.
“Cannot display
Solution
The image data may have
been corrupted.
Pressing [Exit] displays the preview
screen without a thumbnail.
you can not check the
thumbnail image.
Note
❒ If you cannot make copies as you want because of paper type, paper size, or
paper capacity problems, use recommended paper. See “Copy Paper”, About
This Machine.
❒ Using curled paper often causes misfeeds, soiled paper edges, or slipped positions while performing staple or stack printing. When using curled paper,
take the stiffness out of the paper with your hands to straighten out the curl,
or load the paper up side down. Also, to prevent paper from curling, lay paper on a flat surface, and do not lean it against the wall.
13
When the Machine Does Not Operate As Wanted
When a Job is Not Performed
If you cannot execute a function, it may be that the machine is being held up by
another function.
If you cannot execute a function, terminate any other functions currently active,
and then try executing the function again. In certain cases, you can carry out another job (copier, document server, printer, scanner) without canceling the current job being performed. Performing multiple functions simultaneously like
this is called “Multi-accessing”.
Combination Chart
1
❖ Function Compatibility
The chart shows Function Compatibility when print priority is set to “Interleave”. See “Print Priority”, General Settings Guide.
: Simultaneous operations are possible.
: Operation is enabled when the relevant function key is pressed and remote switching (of the scanner/external extension) is done.
: Operation is enabled when the {Interrupt} key is pressed to interrupt the
preceding operation.
→ : Operation is performed automatically once the preceding operation ends.
× : The operation must be started once the preceding operation ends. (Simultaneous operations are not possible.)
14
*1
*1
×
×
×
×
Print
*3
Web Document Server
Printing
Printing from Document Server
Document Server
Operations for Document Server
Printing from Document Server
TWAIN
Scanning
Scanner
Operations for Scanning
Scanning
*2
→ →
×
×
×
×
×
×
→ →
*3
*3
→ →
→
→ →
*4
Operations for
scanning
Scanning
Scanning
*3
→ → →
Stapling
DeskTopBinder Printing from
Document Server
Web Document Printing
Server
*2
*3
×
Data Reception
Document Server Operations for
Document Server
Scanning a Document to Store in
Document Server
Printing from
Document Server
*1
*2
*2
Printing
TWAIN
*2
1
×
*4
*1
Interrupt Copy- Operations for
ing
Copying
Copying
Scanner
Stapling
→
*1
Scanning a Document to Store in Document Server
*1
→ →
Sort
Printer
Print
→ →
*1
Printing
×
Data Reception
Sort
×
Copying
Stapling
×
Operations for Copying
Operations for Copying
Mode before you select
Copy
Operations for
Copying
Stapling
Printer
Interrupt Copying
Mode after you select Copy
DeskTopBinder
When a Job is Not Performed
×
*2
*2
×
×
×
×
×
×
×
*3
×
*2
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
*5
*5
*5
*2
×
×
Simultaneous operations are only possible after the preceding job documents are all
scanned and [New Job] key appears.
You can scan a document after the preceding job documents are all scanned.
During stapling, printing automatically starts after the current job.
15
When the Machine Does Not Operate As Wanted
*4
*5
Stapling is not available.
Simultaneous operation become possible after you press [New Job] key.
Note
❒ Stapling cannot be used at the same time for multiple functions.
❒ If the machine is capable of executing multiple functions simultaneously,
specify which function should have priority in “Print Priority”. This setting is
factory-preset to “Display Mode”. For setting of Printing Priority Function,
see “Print Priority”, General Settings Guide.
❒ When Finisher or Booklet Finisher is installed on the machine, you can specify
the output tray where documents are delivered. See “Output tray settings”,
General Settings Guide.
❒ Operation speed might be reduced if you scan originals while a print job is in
progress.
1
16
2. Troubleshooting When
Using the Copy Function
This chapter explains likely causes of and possible solutions for copier function
problems.
When a Message Appears
This section explains the machine's main messages. If other messages appear,
follow the instructions they contain.
Important
❒ For messages that are not listed here, see p.9 “When You Have Problems Operating the Machine”.
Message
Cause
Solution
Cannot detect
original size.
Improper original is
placed.
Select paper manually, not in Auto Paper Select mode, and do not use Auto
Reduce/Enlarge function. See “Sizes
difficult to detect”, Copy/Document
Server Reference.
Cannot detect
original size.
Improper original is
placed.
Place the original on the exposure glass.
See “Placing Originals on the Exposure
Glass” and “Sizes difficult to detect”,
Copy/Document Server Reference.
Cannot detect
original size.
Original is not placed.
Place your originals.
Check original
orientation.
Original is not placed in a
proper orientation.
Change the orientation of the original.
Check paper size. Improper paper size is set. If you press the {Start} key, copy will
start onto the selected paper.
Rotate Sort is
not available
with this paper
size.
A size of paper for which
Rotate Sort is not available is selected.
Select the proper paper size. See “Sort”,
Copy/Document Server Reference.
Rotate Sort is
not available
with this paper
size.
A size of paper for which
Rotate Sort is not available is selected.
Select the proper paper size. See “Sort”,
Copy/Document Server Reference.
17
Troubleshooting When Using the Copy Function
Message
Cause
Solution
Cannot punch this
paper size.
The Punch function cannot be used with paper
size selected.
The following paper sizes are available
for Punch mode:
2
• 2 holes:
A3L, B4L, A4KL, B5KL,
A5KL, B6L, A6L, 12”×18”L,
11”×17”L, Legal(81/2”×14”)L, Letter(81/2”×11”)KL, Half Letter
(51/2”×81/2”)KL, Executive
(71/4”×101/2”)KL, F/GL
(8”×13”)L, Foolscap (81/2”×13”)L,
Folio (81/4”×13”)L, 11”×15”L,
11”×14”L, 10”×15”L, 10”×14”L,
81/4”×14”L, 8”×10”L, 8KL,
16KKL. Select one of these sizes.
• 3 holes:
A3L, B4L, A4K, B5K, 12”×18”L,
11”×17”L, Letter(81/2”×11”)K, Executive (71/4”×101/2”)K,
11”×15”L, 11”×14”L, 8KL,
16KK. Select one of these sizes.
Stapling capacity
exceeded.
The number of sheets per
set is over the staple capacity.
Cannot staple pa- The Staple function canper of this size. not be used with paper
size selected.
Select a paper size that can be used in
Staple mode. See “Supplementary Informations”, Copy/Document Server
Reference.
Duplex is not
available with
this paper size.
A paper size not available
in Duplex mode has been
selected.
Maximum number of
sets is nn.
The number of copies ex- You can change the maximum copy
ceeds the maximum copy quantity. See “Max. Number of Sets”,
quantity.
General Settings Guide.
(A figure is placed at n.)
File being stored
exceeded max.
number of pages
per file. Copying
will be stopped.
18
Check the stapler capacity. See “Supplementary Informations”, Copy/Document Server Reference.
The scanned originals
have too many pages to
store as one document.
The following paper sizes are available
for Duplex mode: A3L, B4L, A4KL,
B5KL, A5KL, B6L, A6L,
12”×18”L, 11”×17”L, Legal
(81/2”×11”)L, Letter (81/2”×11”)KL,
Half Letter (51/2”×81/2”)KL, Executive (71/4”×101/2”)KL, F/GL
(8”×13”)L, Foolscap (8”×13”)L, Folio
(81/4”×13”)L, 11”×15”L, 11”×14”L,
10”×14”L, 81/4”×14”L, 8”×10”L,
8KL, 16KKL. Select one of these sizes.
Press [Exit], and then store again with
an appropriate number of pages.
When a Message Appears
Message
Magazine or Booklet mode is not
available due to
mixed image mode.
Cause
Solution
You selected the MagaMake sure originals for the Magazine
zine or Booklet function
or Booklet function are scanned using
for originals scanned us- the same function.
ing different functions,
such as copy and printer.
Document Server or
Orig. is being
scanned by anoth- Scanner function is in
use.
er function.
Please wait.
To cancel the job in process, press [Exit],
and then press the {Document Server} or
{Scanner} key. Next, press the {Stop}
key. When the message “The Clear
2
/ Stop key was pressed. Are
you sure you want to stop
scanning?” appears, press [Cancel].
You do not have
the privileges to
use this function.
This user code is not allowed to use the function
selected.
Contact the administrator.
You do not have
the privileges to
use this function.
This user code is not allowed to use the function
selected.
If the message continues to be displayed and you cannot switch the
screen, press the {Energy Saver} key.
Confirm that the display goes off, and
then press the {Energy Saver} key again.
The display will return to the user code
entry display. When printing under the
copier or printer function, press the
{Energy Saver} key only after printing
has finished.
Authentication
has failed.
The entered login user
name or login password
is not correct.
Inquire the user administrator for the
correct login user name and login password.
Authentication
has failed.
The machine cannot perform authentication.
Contact the administrator.
You have tried to delete
The selected
file(s) contained files without the authority to do so.
file(s) without
access privileges. Only file(s)
with access privileges will be
deleted.
Files can be deleted by the person who
created the file. To delete a file which
you are not authorized to delete, contact the person who created the file.
19
Troubleshooting When Using the Copy Function
Message
Please wait.
2
Cause
Solution
The destination list is be- Wait until the message disappears. Do
ing updated from the net- not switch off the power while this
work using
message is displayed.
SmartDeviceMonitor for
Admin. Depending on
the number of destinations to be updated, there
may be some delay before you can resume operation. Operations are
not possible while this
message is displayed.
It will be neces- A misfeed occurred when
unneeded tab stock was
sary to start
ejected.
over and reload
the tab stock to
the trays.
Remove the jammed sheet.
If cycle printing is specified for tab
stock sheets, both needed and unneeded tab stock is ejected when copying restarts. Reload the tab stock trays before
the new print cycle begins.
After resetting the tab stock pages,
press [Exit]. To resume printing, press
the {Start} key.
❖ Connect Copy
Message
Cause
Solution
Cannot connect to
the sub-machine.
Check the status
of the sub-machine.
• The L indicator is lit.
Press [Exit] on the main machine and
follow the instructions on the display.
Cannot print from
the sub-machine.
Check the status
of the sub-machine.
A paper misfeed has occurred on the sub-machine, or toner or other
supplies need to be replenished.
Follow the instructions displayed. For
details, see p.82 “Adding Toner”, p.87
“Removing Jammed Paper”, p.100 “Removing Jammed Staples”.
Cannot print from
the sub-machine.
Check the status
of the sub-machine.
The sub-machine's User
Tools menu is open.
Press the {User Tools} key to close the
User Tools menu.
Sub-machine is in
Interrupt mode.
The sub-machine is in In- Press the {Interrupt} key on the sub-materrupt mode.
chine to cancel Interrupt mode.
• The hard disk of the
sub-machine is malfunctioning.
Sub-machine does Paper type or tray setnot have the same tings on the two mapaper setting(s). chines do not match.
20
If the sub-machine's display indicates
that a cover is open, follow the instructions displayed.
Make the same settings on both machines.
When a Message Appears
Message
Cause
Solution
Cover settings on the two Make the same settings on both maThe Cover Sheet
setting(s) of the machines do not match. chines.
sub-machine is
different from
the main machine.
Slip Sheet settings on the Make the same settings on both maThe Slip Sheet
chines.
setting(s) of the two machines do not
match.
sub-machine is
different from
the main machine.
The Designation
Sheet setting(s)
of sub-machine is
different from
main machine.
Designation Sheet settings on the two machines do not match.
Make the same settings on both machines.
Sub-machine paper
settings must be
the same to use
this tray.
Paper tray settings on the
two machines do not
match.
Make the same settings on both machines.
No stamp data in
the sub-machine.
Stamp data on the submachine has been deleted.
Reprogram the stamp on the sub-machine.
Cannot print from
the sub-machine.
Sub-machine will
be disconnected.
The sub-machine has
stopped due to power
failure or communication
error.
Continue copying using the main machine.
Z-fold is available only when
Sort mode is selected in Connect
Copy.
Sort has not been selected
with Z-fold.
Select the Sort function.
2
Reference
p.9 “When You Have Problems Operating the Machine”
21
Troubleshooting When Using the Copy Function
Display During Connect Copy
This section explains about the display during Connect Copy.
2
22
Problem
Cause
Solution
[Connect Copy] is not displayed.
The sub-machine's main
power is off.
Turn on the sub-machine's main power.
[Connect Copy] is not displayed.
Functions that cannot be Cancel the functions selected on the
used with Connect Copy main machine.
are selected on the main
machine (such as storing
or copying the first page
of a document in the Document Server).
[Connect Copy] is not displayed.
The main machine is in
Interrupt mode.
[Connect Copy] is not displayed.
The [Connect Copy Key Dis- Select [Display] for the [Connect Copy Key
play] setting is off.
Display] setting.
[Connect Copy] is not displayed.
The cable connecting the
two machines is damaged.
Contact your service representative.
[Connect Copy] is not displayed.
The L is lit.
Follow the instructions displayed.
[Connect Copy] appears
faded.
Functions that cannot be
used with Connect Copy
have been set.
Press the {Clear Modes} key to clear the
settings.
Press the {Interrupt} key on the sub-machine to cancel Interrupt mode.
If Connect Copy is Cancelled
If Connect Copy is Cancelled
This section explains about causes and remedies when Connect Copy is cancelled.
Problem
Cause
Solution
The machine cancels
Connect Copy.
The main machine's
main power is off, or the
operation switch has
been pressed.
Turn on the sub-machine's main power
or operation switch, and then press
[Connect Copy].
The machine cancels
Connect Copy.
The sub-machine's main
power is off.
A message instructing you to check the
sub-machine appears on the display of
the main machine. Press [Cancel] to clear
Connect Copy. Turn on the sub-machine's main power, press [Connect
Copy] and then make your settings
again.
The machine cancels
Connect Copy.
The Weekly Timer setting is coming into effect
on the main machine.
Turn on the main machine's operation
switch , and then press [Connect Copy].
An error message indicates the main machine
has broken down.
The L is lit.
Copying is not possible. Follow the instructions displayed.
2
23
Troubleshooting When Using the Copy Function
If You Cannot Exit from Connect Copy
This section explains about causes and remedies if you cannot exit from Connect
Copy.
Problem
2
Cause
Solution
There is no response when
you press [Connect Copy].
Scanning is in progress.
Press the {Stop} key on the main machine, and then press [Stop].
There is no response when
you press [Connect Copy].
Copying is in progress.
Press the {Stop} key on the main machine, and then press [Stop].
There is no response when
you press [Connect Copy].
A paper misfeed has occurred on either the main
machine or sub-machine.
Follow the instructions displayed.
For details, see p.87 “Removing
Jammed Paper” and p.100 “Removing
Jammed Staples”.
If the sub-machine's display indicates
that a cover is open, follow the instructions displayed.
There is no response when
you press [Connect Copy].
A paper misfeed has occurred on either the main
or sub-machine.
To cancel Connect Copy, Press the
{Stop} key on the main machine, and
then press [Stop].
There is no response when
you press [Connect Copy].
A paper misfeed has occurred on one of the machine, or toner or other
supplies need to be replaced.
Follow the instructions displayed.
There is no response when
you press [Connect Copy].
A paper misfeed has occurred on one of the machine, or toner or other
supplies need to be replaced.
To cancel Connect Copy, press the
{Stop} key on the main machine, and
then press [Stop].
There is no response when
you press [Connect Copy].
A paper misfeed has occurred during stapling.
Removed the jammed paper.
For details, see p.59 “Loading paper”,
p.82 “Adding Toner”, and p.87 “Removing Jammed Paper”.
For details, see p.100 “Removing
Jammed Staples”.
To cancel Connect Copy, press the
{Stop} key on the main machine, and
then press [Stop].
24
When You Cannot Make Clear Copies
When You Cannot Make Clear Copies
This section explains likely causes of and possible solutions for unclear copies.
Problem
Cause
Solution
Copies appear dirty.
Image density is too high. Adjust the image density. See “Adjusting Copy Image Density”, Copy/Document Server Reference.
Copies appear dirty.
Auto Image Density is
not selected.
The reverse side of an
original image is copied.
Image density is too high. Adjust the image density. See “Adjusting Copy Image Density”, Copy/Document Server Reference.
The reverse side of an
original image is copied.
Auto Image Density is
not selected.
A shadow appears on
copies if you use pasted
originals.
Image density is too high. Adjust the image density. See “Adjusting Copy Image Density”, Copy/Document Server Reference.
2
Adjust the auto density. See “Adjusting
Copy Image Density”, Copy/Document Server Reference.
Adjust the auto density. See “Adjusting
Copy Image Density”, Copy/Document Server Reference.
Change the orientation of the original.
Put mending tape on the pasted part.
The same copy area is
dirty whenever making
copies.
The exposure glass or
ADF is dirty.
Clean them. See p.107 “Maintaining
Your Machine”.
The same copy area is
dirty whenever making
copies.
The original that has already been printed is
scanned.
Select [Generation Copy], and then begin
copying. See “Generation Copy”,
Copy/Document Server Reference.
Copies are too light.
Image density is too light. Adjust the image density. See “Adjusting Copy Image Density”, Copy/Document Server Reference.
Copies are too light.
A light copy may result
when you use damp or
rough grain paper.
Use the recommended paper. also, use
paper that has been stored in the recommended temperature and humidity
condition. See “Copy Paper”, About
This Machine.
Contact your service representative.
Copies are too light.
Toner bottle is almost
empty.
Add toner. See p.82 “Adding Toner”.
Parts of images are not
copied.
The original is not set cor- Set originals correctly. See “Placing
rectly.
Originals”, Copy/Document Server
Reference.
Parts of images are not
copied.
The correct paper size is
not selected.
Select the proper paper size.
25
Troubleshooting When Using the Copy Function
Problem
2
Cause
Solution
Images appear only partially.
The paper is damp.
Use paper that has been stored in the
recommended temperature and humidity condition. See “Copy Paper”,
About This Machine.
Black lines appear.
The exposure glass is
dirty.
Clean them. See p.107 “Maintaining
Your Machine”.
White lines appear.
The exposure glass is
dirty.
Clean them. See p.107 “Maintaining
Your Machine”.
White lines appear.
When D is blinking, ton- Add toner. See p.82 “Adding Toner”.
er is beginning to run out.
Copies are blank.
The original is not set cor- When using the exposure glass, face the
rectly.
originals down. When using the ADF,
face them up.
A moiré pattern is produced on copies.
Your original has a dot
pattern image or many
lines.
Black spots appear on the
copy of a photographic
print.
Because of high humidi- Place the print on the exposure glass in
ty, the photographic print either of the following ways:
has stuck to the exposure • Place an OHP transparency on the
glass.
exposure glass, and then place the
print on top of the OHP transparency.
Place the original on the exposure glass
at a slight angle.
• Place the print on the exposure
glass, and then place two or three
sheets of white paper on top of it.
Leave the auto-document feeder
(ADF) open when copying.
26
When You Cannot Make Copies As Wanted
When You Cannot Make Copies As Wanted
This section explains likely causes of and possible solutions for unclear copies.
❖ Basic
Problem
Cause
Solution
2
Misfeeds occur frequently. The number of sheets
Load paper only as high as the upper
loaded exceeds the capac- limit markings on the side fence of the
ity of the machine.
paper tray or bypass tray. See “Copy
Paper”, About This Machine.
Misfeeds occur frequently. The paper is damp.
Use paper that has been stored in the
recommended temperature and humidity condition. See “Copy Paper”,
About This Machine.
Misfeeds occur frequently. The paper is too thick or
too thin.
Use recommended paper. See “Copy
Paper”, About This Machine.
Misfeeds occur frequently. The copy paper is wrinkled or has been folded/creased.
Use recommended paper. Use paper
that has been stored in the recommended temperature and humidity condition. See “Copy Paper”, About This
Machine.
Misfeeds occur frequently. Printed paper is being
used.
Use recommended paper. Do not use
paper that has been already copied or
printed onto. See “Copy Paper”, About
This Machine.
Copy paper becomes
creased.
The paper is damp.
Use paper that has been stored in the
recommended temperature and humidity condition. See “Copy Paper”,
About This Machine.
Copy paper becomes
creased.
The paper is too thin.
Use recommended paper. See “Copy
Paper”, About This Machine.
Copies are not stapled.
There are jammed staples
in the stapler.
Remove jammed staples. See p.100 “Removing Jammed Staples”.
Copies are not stapled.
The number of copies ex- Check the stapler capacity. See “Supceeds the capacity of the plementary Informations”, Copy/Docstapler.
ument Server Reference.
Copies are not stapled.
Copy paper is curled.
Turn the copy paper over in the tray.
Staples are wrongly posi- Originals are not set cortioned.
rectly.
Check the correct position to place the
originals. See “Staple”, Copy/Document Server Reference.
You cannot combine sev- Selected functions cannot
eral functions.
be used together.
Check the combination of functions
and make the settings again. See “Function Compatibility”, Copy/Document
Server Reference.
27
Troubleshooting When Using the Copy Function
2
Problem
Cause
Solution
When sorting, the pages
are divided into two
blocks.
The memory became full
in the middle of sorting
and the pages were delivered in two blocks.
You can interrupt copying when the
memory becomes full. See “Memory
Full Auto Scan Restart”, General Settings Guide.
Paper does not output
during printing with stapling.
When you stop printing
while using the staple
function, paper not stapled during printing may
be left in the staple unit.
Press the {Clear Modes} key and cancel
copy settings, including stapling.
Images are skewed.
The side fences in the pa- Make sure the paper guide is locked.
per feed tray is not
See p.70 “Changing the Paper Size”.
locked.
Images are skewed.
The paper is feeding in at
a slant.
Load the paper correctly. See p.59
“Loading paper”.
❖ Edit
Problem
In Double Copies mode,
parts of the original image are not copied.
Cause
Solution
Combination of original Select A3L for A4K originals and A4
and copy paper is not cor- for A5 originals.
rect.
In Border, Centre, or Cen- You set a wide erased
tre/ Border mode, parts
margin.
of the original image are
not copied.
Make the margin width narrower. You can
adjust it between 2 - 99 mm (0.1” - 3.9”).
See “Erase Border Width” and “Erase Centre Width”, General Settings Guide.
In Border, Centre, or Cen- Originals are not scanned
tre/ Border mode, parts
correctly.
of the original image are
not copied.
Place the originals correctly.
In Margin Adjustment
You set a wide erased
mode, parts of the origi- margin.
nal image are not copied.
Set a narrower margin with User Tools.
You can set the width between 0 - 30
mm (0” - 1.2”).
See “Front Margin: Left/Right”, “Back
Margin: Left/Right”, “Front Margin:
Top/Bottom” and “Back Margin:
Top/Bottom”, General Settings Guide.
In Margin Adjustment
There is a lack of margin
mode, parts of the origi- space on the opposite
nal image are not copied. side of the binding position.
In Image Repeat mode,
the original image is not
copied repeatedly.
28
Set a narrower margin with User Tools.
You can set the width between 0 - 30
mm (0” - 1.2”).
See “Front Margin: Left/Right”, “Back
Margin: Left/Right”, “Front Margin:
Top/Bottom” and “Back Margin:
Top/Bottom”, General Settings Guide.
You selected copy paper Select copy paper larger than the origithe same size as the origi- nals or select the proper reproduction
nals, or you did not select ratio.
the proper reproduction
ratio.
When You Cannot Make Copies As Wanted
❖ Stamp
Problem
Cause
Solution
The stamp position is
wrong.
The paper orientation is
wrong.
Check the paper orientation and stamp
position.
The stamp is not printed
on the back side of sheets
when duplex copying.
The back side stamp posi- Reset the back side stamp position. See
tion is incorrect for the
“Back Side Stamp Position in Duplex”,
paper size.
General Settings Guide.
2
❖ Combine
Problem
Cause
Solution
You cannot make a book
from Booklet or Magazine mode by folding
copies.
You selected a setting
(“Open to left”or “Open
to right”) that does not
match the orientation of
originals.
Change the setting. See “Orientation:
Booklet, Magazine”, General Settings
Guide.
When using Combine,
parts of the image are not
copied.
You specified a reproduction ratio that does not
match the sizes of your
originals and copy paper.
When you specify a reproduction ratio
using Manual Paper Select mode, make
sure that the ratio matches your originals and the copy paper. Select the correct reproduction ratio before using
Combine mode.
Copies are not in correct
order.
You placed the originals
in the incorrect order.
When placing a stack of originals in the
ADF, the last page should be on the bottom.
If you place an original on the exposure
glass, start with the first page to be copied.
❖ Duplex
Problem
Cause
Solution
Cannot print in duplex
mode.
You have selected a tray
which is set to [1 Sided
Copy] in [Tray Paper Settings] in [System Settings].
Set the tray to [2 Sided Copy] in [Tray Paper Settings] in [System Settings]. See
“System Settings”, General Settings
Guide.
Copies are not in correct
order.
You placed the originals
in the incorrect order.
When placing a stack of originals in the
ADF, the last page should be on the bottom.
If you place an original on the exposure
glass, start with the first page to be copied.
When using Duplex,
copy is made Top to Bottom even though [Top to
Top] is selected.
You placed the originals
in the wrong orientation.
Place the original in the correct orientation. See “Original Orientation”,
Copy/Document Server Reference.
29
Troubleshooting When Using the Copy Function
❖ Connect Copy
Problem
You cannot staple,
punch, or Z-fold.
Cause
The main and sub-machines do not have the
same option installed.
You get different copy re- The Copy Quality setting
sults from the main and
differs on the two masub-machines.
chines.
2
Solution
Press [Connect Copy] to cancel Connect
Copy.
Make the same Copy Quality setting
one the two machines.
When Memory is Full
This section explains likely causes of and possible solutions for problems related
to full memory.
Message
Cause
Solution
Memory is full.
nn originals have
been scanned.
Press [Print] to
copy scanned
originals. Do not
remove remaining
originals.
The scanned originals exceeds the number of pages that can be stored in
memory.
Press [Print] to copy scanned originals
and cancel the scanning data. Press
[Stop] to cancel the scanning data and
not copy.
The machine checked if
the remaining originals
should be copied, after
the scanned originals was
printed.
To continue copying, remove all copies,
and then press [Continue]. To stop copying, press [Stop].
Cause
Solution
“n” in the message represents a changeable number.
Press [Continue]
to scan and copy
remaining originals.
❖ Connect Copy
Message
Sub-machine memo- The quantity of data exry is full. Sub- ceeds the capacity of the
sub-machine.
machine will be
disconnected.
Continue printing on the main machine.
Note
❒ If you set [Memory Full Auto Scan Restart] in User Tools to [On], even if the memory becomes full, the memory overflow message will not be displayed. The
machine will make copies of the scanned originals first, then automatically
proceed scanning and copying the remaining originals. In this case, the resulting sorted pages will not be sequential. See “Input / Output”, General Settings Guide.
30
3. Troubleshooting When
Using the Printer Function
This chapter explains likely causes of and possible solutions for printer function
problems.
When a Message Appears during
Installation of the Printer Driver
This section explains what to do if a message appears when installing the printer
driver.
The following describes operations when a message appears during installation
of the printer driver. Message number 58 or 34 indicates that the printer driver
cannot be installed using Auto Run. Install the printer driver using [Add Printer]
or [Install Printer].
Message number 58 appears if there is a newer version of the printer driver already installed.
Windows 95/98/Me
This section explains the procedure under Windows 95/98/Me.
A On the [Start] menu, point to [Settings], and then click [Printers].
B Double-click the Add Printer icon.
C Follow the instructions in Add Printer Wizard.
If the CD-ROM drive is D, the source files of the printer driver are stored in
the following location:
• RPCS (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\RPCS\WIN9X_ME\(Language)\DISK1
• PCL 5e (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\PCL5E\WIN9X_ME\(Language)\DISK1
• PCL 6 (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\PCL6\WIN9X_ME\(Language)\DISK1
• PostScript 3 (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\PS\WIN9X_ME\(Language)\DISK2
If the installer starts, click [Cancel] to quit.
31
Troubleshooting When Using the Printer Function
Windows 2000
This section explains the procedure under Windows 2000.
A On the [Start] menu, point to [Settings], and then click [Printers].
B Double-click the Add Printer icon.
C Follow the instructions in Add Printer Wizard.
If the CD-ROM drive is D, the source files of the printer driver are stored in
the following location:
• RPCS (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\RPCS\WIN2K_XP\(Language)\DISK1
• PCL 5e (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\PCL5E\WIN2K_XP\(Language)\DISK1
• PCL 6 (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\PCL6\WIN2K_XP\(Language)\DISK1
• PostScript 3 (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\PS\WIN2K_XP\(Language)\DISK2
If the installer starts, click [Cancel] to quit.
3
Windows XP, Windows Server 2003
This section explains the procedure under Windows XP or Windows Server
2003.
A On the [Start] menu, click [Printers and Faxes].
B Click [Add a printer].
C Follow the instructions in Add Printer Wizard.
If the CD-ROM drive is D, the source files of the printer driver are stored in
the following location:
• RPCS (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\RPCS\WIN2K_XP\(Language)\DISK1
• PCL 5e (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\PCL5E\WIN2K_XP\(Language)\DISK1
• PCL 6 (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\PCL6\WIN2K_XP\(Language)\DISK1
• PostScript 3 (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\PS\WIN2K_XP\(Language)\DISK2
If the installer starts, click [Cancel] to quit.
32
When a Message Appears during Installation of the Printer Driver
Windows NT 4.0
This section explains the procedure under Windows NT 4.0.
A On the [Start] menu, point to [Settings], and then click [Printers].
B Double-click the Add Printer icon.
C Follow the instructions in Add Printer Wizard.
If the CD-ROM drive is D, the source files of the printer driver are stored in
the following location:
• RPCS (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\RPCS\NT4\(Language)\DISK1
• PCL 5e (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\PCL5E\NT4\(Language)\DISK1
• PCL 6 (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\PCL6\NT4\(Language)\DISK1
• PostScript 3 (“Printer Drivers and Utilities” CD-ROM)
D:\DRIVERS\PS\NT4\(Language)\DISK2
If the installer starts, click [Cancel] to quit.
3
33
Troubleshooting When Using the Printer Function
If USB Connection Fails
This section explains how to troubleshoot a problem related to USB connection.
Problem
3
Cause
Solution
The machine is not automatically recognized.
The USB cable is not con- Turn off the power of the machine, renected properly.
connect the USB cable, and then turn it
on again.
Windows has already
configured the USB settings.
Check whether the computer has identified the
machine as an unsupported device.
Open Windows' Device Manager, and
then, under [Universal Serial Bus controllers], remove any conflicting devices.
Conflicting devices have a [!] or [?] icon
by them. Take care not to accidentally
remove required devices. For details,
see Windows Help.
When using Windows 2000 / XP or
Windows Server 2003, an erroneous device is displayed under [USB Controller]
in the [Device Manager] dialog box.
Windows Me and the ma- You need to download
chine cannot be connect- USB Printing Support for
ed.
Windows Me.
34
Download USB Printing Support from
the supplier's website.
Search the model name you use on the
supplier's website, and download USB
Printing Support.
When a Message Appears
When a Message Appears
This section describes the principal messages that appear on the panel display.
If a message not described here appears, act according to the message.
Reference
Before turning the main power off, see “Turning On/Off the Power”, About
This Machine.
Status Messages
3
This section describes the machine status messages.
Message
Problem
Ready
This is the default ready message. The machine is ready
for use. No action is required.
Printing...
The machine is printing. Wait a while.
Waiting...
The machine is waiting for the next data to print. Wait a
while.
Offline
The machine is offline. To start printing, switch the machine online by pressing {Online} key.
Please wait.
The machine is preparing the development unit. Wait a
while.
Resetting job...
The machine is resetting the print job. Wait until
“Ready” appears on the display panel.
Setting change...
The machine is setting changing. Wait a while.
Hex Dump Mode
In the Hex Dump mode, the machine receives data in
hexadecimal format. Turn off the machine after printing, and then turn back on.
35
Troubleshooting When Using the Printer Function
Alert Messages
This section describes the machine Alert messages.
Message
Cause
Solution
Problem with Hard
Disk.
An error has occurred in
the hard disk drive.
Turn off the main power switch, and
back on again. If the message appears
again, contact your service representative.
The entered pass- The password of the en- Enter the correct password.
crypted PDF file has been
word is incorentered incorrectly.
rect.
3
USB has a problem. An error has occurred in
the USB interface.
Hardware Problem:
Ethernet
An error has occurred in
the Ethernet board.
Turn off the main power switch, and
back on again. If the message appears
again, contact your service representative.
Turn off the main power switch, and
back on again. If the message appears
again, contact your service representative.
Use of this function is re- Contact the administrator.
You do not have
the privileges to stricted.
use this function.
Authentication
has failed.
• The login user name
or password entered
is incorrect.
• Check your login user name and
password.
• Contact the administrator.
• The machine currently cannot perform authentication.
An error has occurred in
Parallel I/F
board has a prob- the parallel interface
board.
lem.
Turn off the main power switch, and
back on again. If the message appears
again, contact your service representative.
Printer font error. An error has occurred in
Contact your service representative.
the font settings.
Memory Overflow
36
Maximum capacity of
PCL 5e/6 or PostScript 3
list display has been exceeded.
Reduce the value of [Resolution] in the
printer driver. Alternatively, select
[Frame Priority] from [Memory Usage] in
[System]. If this message continues to
appear after taking these steps, decrease the number of files sent to the
machine.
When a Message Appears
Checking the Error Log
If files could not be stored due to printing errors, identify the cause of the errors
by checking the error log on the control panel.
A Press the {Printer} key to display the printer screen.
3
ANR103S
B Press [Error Log].
An error log list appears.
Note
❒ The most recent 50 errors are stored in the error log. If a new error is added
when there are 50 errors already stored, the oldest error is deleted. However, if the earliest error is a Sample Print, Locked Print, Hold Print, or
Stored print error, it is not deleted. The error is stored separately until the
number of errors reaches 30.
❒ If the main power switch is turned off, the log is deleted.
37
Troubleshooting When Using the Printer Function
When You Cannot Print
Use the following procedures if printing does not start even after performing
[Print].
Problem
3
Cause
Solution
Printing does not start.
The power is off.
Check the cable is securely plugged
into the power outlet and the machine.
Turn on the main power switch.
Printing does not start.
The machine is set to “Of- Press the {Online} key.
fline”.
Printing does not start.
The cause is displayed on
the display of the control
panel.
Check the error message or warning
status on the display panel and take the
required action.
Printing does not start.
The interface cable is not
connected correctly.
Connect the interface cable securely. If
it has a fastener, fasten that securely as
well. See “Connecting to the Interfaces”, General Settings Guide.
Printing does not start.
The correct interface cable is not being used.
The type of interface cable you should
use depends on the computer. Be sure
to use the correct one. If the cable is
damaged or worn, replace it. See “Connecting to the Interfaces”, General Settings Guide.
Printing does not start.
The interface cable was
connected after the machine was switched on.
Connect the interface cable before turning on the machine.
Printing does not start.
The login user name, log- Check the login user name, login passin password, or driver
word, or driver encryption key.
encryption key is invalid.
Printing does not start.
Advanced encryption has Check the settings of the Extended Sebeen set using the Excurity function with the administrator.
tended Security function.
Data-in lamp does not
blink or light up.
If the data-in lamp is unlit
or not flashing even after
performing [Print], the
machine has not received
the data.
• When the machine is connected to a
computer via a cable, check the
computer print port settings are correct. See “Confirming the Connection Method”, Printer Reference.
• When it is networked with a computer, Contact the administrator.
The status indicator of
the printer is lit.
38
The cause is displayed on
the display of the control
panel.
Check the error message on the display
panel and take required action. See p.35
“When a Message Appears”.
When You Cannot Print
Problem
“Updating the
destination
list... Please
wait. Specified
destination(s) or
sender's name has
been cleared.” ap-
Cause
Solution
The destination list is being updated from the network using
SmartDeviceMonitor for
Admin.
Wait until the message disappears. Do
not switch off the power while this
message is displayed. Depending on
the number of destinations to be updated, there may be some delay before you
can resume operation. Operations are
not possible while this message is displayed.
A mechanical error might
have occurred.
Contact your service representative.
See “List/Test Print”, General Settings
Guide.
pears.
[List / Test Print] is disabled.
3
If the printing does not start, consult your service representative.
❖ When the machine is connected to the computer using the interface cable
The following shows how to check the print port when the data-in lamp does
not light up or blink.
Check if the print port setting is correct. When it is connected using a parallel
interface, connect it to LPT1 or LPT2.
For Windows 95/98/Me
A Click the [Start] button, point to [Settings], and then click [Printers].
B Click the icon of the machine. On the [File] menu, click [Properties].
C Click the [Details] tab.
D In the [Print to the following port:] list, confirm the correct port is selected.
For Windows 2000 or Windows NT 4.0
A Click the [Start] button, point to [Settings], and then click [Printers].
B Click the icon of the machine. On the [File] menu, click [Properties].
C Click the [Ports] tab.
D In the [Print to the following port(s)] list, confirm the correct port is selected.
For Windows XP
A Click the [Start] button, and then click [Printers and Faxes].
B Click the icon of the machine. On the [File] menu, click [Properties].
C Click the [Ports] tab.
D In the [Print to the following port(s)] list, confirm the correct port is selected.
For Windows Server 2003
A Click the [Start] button, point to [Settings], and then click [Printers and Faxes].
B Click the icon of the machine. On the [File] menu, click [Properties].
C Click the [Ports] tab.
D In the [Print to the following port(s)] list, confirm the correct port is selected.
39
Troubleshooting When Using the Printer Function
Other Printing Problems
This section explains likely causes of and possible solutions for problems that
can occur when printing from a computer.
Problem
Print has smudges.
3
40
Cause
Settings for thick paper have not been
made when printing
on thick paper in the
bypass tray.
Solution
• PCL 5e/6 and PostScript 3
Select [Thick] in the [Type:] list on the [Paper]
tab.
• RPCS
Select [Thick] in the [Paper type:] list on the
[Print Settings] tab.
The print on the entire
page is faded.
When D is blinking,
toner is beginning to
run out.
Add toner. See p.82 “Adding Toner”.
The print on the entire
page is faded.
The paper is damp.
Use paper that has been stored in the recommended temperature and humidity condition.
See “Copy Paper”, About This Machine.
The print on the entire
page is faded.
The paper is unsuitable.
Use the recommended paper. (Printing on
coarse or treated paper might result in faint
print image.) See “Copy Paper”, About This
Machine.
The print on the entire
page is faded.
If the [Toner saving]
check box is selected
in the printer driver
settings, the entire
page will be faded
when printed.
For the RPCS printer driver, [Toner saving] is located on the [Print Quality] tab. For the PostScript 3 printer driver, see PostScript 3
Supplement. See the printer driver Help.
Image bleeds when
rubbed.
If you are using thick
paper, [Paper type:]
might not be set to
[Thick].
On the printer driver's [Setup] tab, set [Paper
type:] to [Thick]. See the printer driver Help.
Paper is not fed from
the selected tray.
When you are using a
Windows operating
system, printer driver
settings override
those settings using
the display panel.
Set the desired input tray using the printer
driver. See the printer driver Help.
The printed image is
different from the image on the computer's
display.
With certain funcIn the application, change the layout, character
tions, such as enlarge- size, and character settings.
ment and reduction,
image layout might
be different to that on
the computer display.
The printed image is
different from the image on the computer's
display.
You might have selected to replace True
Type fonts with machine fonts in the
printing process.
To print an image similar to that of the computer display, make settings to print True
Type fonts as an image. See the printer driver
Help.
Other Printing Problems
Problem
Cause
Solution
Images are printed at
slant.
The tray's side fences
might not be locked.
Check the side fences are locked. See p.70
“Changing the Paper Size”.
Print is slanted.
The paper is feeding
in at a slant.
Load the paper correctly. See p.59 “Loading
paper”.
Misfeeds occur frequently.
The number of sheets Load paper only as high as the upper limit
loaded exceeds the ca- markings on the side fences of the paper tray
pacity of the machine. or bypass tray. See “Copy Paper”, About This
Machine.
Misfeeds occur frequently.
The paper is damp.
Use paper that has been stored in the recommended temperature and humidity condition.
See “Copy Paper”, About This Machine.
Misfeeds occur frequently.
The paper is too thick
or too thin.
Use recommended paper. See “Copy Paper”,
About This Machine.
Misfeeds occur frequently.
The copy paper is
wrinkled or has been
folded/creased.
Use recommended paper. Use paper that has
been stored in the recommended temperature
and humidity condition. See “Copy Paper”,
About This Machine.
Misfeeds occur frequently.
Printed paper is being
used.
Use recommended paper. See “Copy Paper”,
About This Machine.
Copy paper becomes
creased.
The paper is damp.
Use paper that has been stored in the recommended temperature and humidity condition.
See “Copy Paper”, About This Machine.
Copy paper becomes
creased.
The paper is too thin.
Use recommended paper. See “Copy Paper”,
About This Machine.
White lines appear.
When D is blinking,
toner is beginning to
run out.
Add toner. See p.82 “Adding Toner”.
When printing graph- If the printer driver is
ics, the output and the configured to use the
screen are different.
graphics command,
the graphics command from the machine is used to print.
If you want to print accurately, set the printer
driver to print without using the graphics
command. See the printer driver Help.
Garbled characters
are printed.
The correct printer
language might have
not been selected.
Set the correct printer language.
Images are printed in
the wrong orientation.
The feed orientation
you selected and the
feed orientation selected in the printer
driver's option setup
might not be the
same.
Set the machine's feed orientation and the
printer driver's feed orientation accordingly.
See the printer driver Help.
There is considerable
delay between the
print start instruction
and actual printing.
“Off mode / Sleep
mode” might be set.
The machine requires time to warm up if it has
been in “Off mode/Sleep mode”. Specify “Off
mode/Sleep mode” in [System Settings], [Auto
Off Timer].
3
41
Troubleshooting When Using the Printer Function
Problem
Cause
There is considerable
delay between the
print start instruction
and actual printing.
Processing time depends on data volume. High volume
data, such as graphics-heavy documents,
take longer to process.
Solution
If the data-in lamp is blinking, data has been
received by the printer. Wait for a moment.
Making the following setting on the printer
driver may reduce the computer's workload.
❖ PCL 5e/6
Select the lower value for [Resolution] on
the [Print Quality] tab in the printer properties dialog box.
❖ PostScript 3
3
Select the lower value in [Resolution]. The
location of this setting is given below. If
your operating system is Windows, select
[PostScript (optimize for speed)] in [PostScript
Output Option]. [PostScript Output Option] is
located as follows:
• Windows 95 / 98 / Me
[Print Quality] tab in the printer properties dialog box.
• Windows 2000 / XP, Windows Server
2003
[PostScript Output Option] in [PostScript
Options] on [Advanced...] on [Layout] tab
in the printing preferences dialog box.
• Windows NT 4.0
[File] on [Advanced...] on [Document Defaults] tab in the printing preferences dialog box.
• Mac OS 9.x
[Printer Specifications] in the print dialog
box.
• Mac OS X
[Set 3] tab in [Printer Features] in the print
dialog box.
If you use Windows, select [PostScript (optimize for speed)].
• Windows 95 / 98 / Me
[PostScript output format:] on the [PostScript] tab in the printer properties dialog box.
• Windows 2000 / XP, Windows Server
2003
[PostScript Output Option] in [PostScript
Options] on [Advanced...] on [Layout] tab
in the printing preferences dialog box.
• Windows NT 4.0
[File] on [Document Defaults] on [Advanced...] tab in the printing preferences
dialog box.
42
Other Printing Problems
Problem
Cause
There is considerable
delay between the
print start instruction
and actual printing.
Processing time depends on data volume. High volume
data, such as graphics-heavy documents,
take longer to process.
Solution
❖ RPCS
Select the lower value for [Resolution:] on
the [Print Quality] tab in the printer driver's
dialog box.
Select [Fast] for the [Document type] list on
the [Print Quality] tab in the printer driver's
dialog box.
To enable [Change User Settings...], select the
[User settings] check box.
See the printer driver Help.
Images are cut off, or
excess is printed.
You may be using paper smaller than the
size selected in the application.
Use the same size paper as that selected in the
application. If you cannot load paper of the
correct size, use the reduction function to reduce the image, and then print. See the printer
driver Help.
Page layout is not as
expected.
Print areas differ depending on machine
used. Information
that fits on a single
page on one machine
may not fit on a single
page of another machine.
Adjust the [Printable area:] setting in the [Printer
Configuration...] dialog box on the [Print Settings]
tab in the RPCS printer driver. See the printer
driver Help.
Photo images are
coarse.
Some applications
print at lower resolution.
Use the application's settings to specify a higher resolution.
Solid lines are printed
as broken lines.
Dither patterns do not
match.
Make the following settings with the printer
driver: Change the [Dithering:] setting on the
[Image Adjustments] tab in the [Change User Settings...] dialog box, on the [Print Quality] tab in
the RPCS printer driver. See the printer driver
Help.
Optional components
connected to the machine are not recognized when using
Windows 95 / 98 /
Me, Windows 2000 /
XP, Windows Server
2003, and Windows
NT 4.0.
Bidirectional communication is not working.
Set up optional devices on the Properties of the
printer.
Duplex printing is
malfunctioning.
Duplex printing cannot be done with paper set in the bypass
tray.
When using duplex printing, make settings to
use paper from a tray other than the bypass
tray.
Duplex printing is
malfunctioning.
The upper tray cannot
be used as an output
destination in duplex
mode.
Specify a another output tray.
3
See the printer driver Help.
43
Troubleshooting When Using the Printer Function
Problem
3
Cause
Solution
Duplex printing is
malfunctioning.
Duplex printing cannot be done with a
tray for which [1 Sided
Copy] has been specified as Paper Type on
the System Settings
menu.
Change the Paper Type setting for the tray to
[2 Sided Copy] on the System Settings menu.
See “System Settings”, General Settings
Guide.
When using Windows 95 / 98 / Me /
2000 / XP, Windows
Server 2003, or Windows NT 4.0, combined printing or
booklet printing does
not come out as expected.
The correct applicaMake sure the application's paper size and orition or printer driver entation settings match those of the printer
settings are not made. driver. If a different paper size and orientation
are set, select the same size and orientation.
A print instruction
was issued from the
computer, but printing did not start.
User Authentication
may have been set.
Contact the administrators.
PDF files do not print
out/cannot perform
[PDF Direct Print].
PDF files are password-protected.
To print password-protected PDF files, enter
the password in the [PDF Menu] or on Web Image Monitor.
• For details about [PDF Menu], see “PDF
Menu”, General Settings Guide.
• For details about Web Image Monitor, see
the Web Image Monitor Help.
PDF files do not print
out/cannot perform
[PDF Direct Print].
PDF files cannot be
printed if they are
print-disabled via
PDF File Security.
Change the PDF File Security setting.
PDF files do not print
out/cannot perform
[PDF Direct Print].
High compression
PDF files created using the machine's
scanner function cannot print directly.
Open the application used to create the PDF,
and then print the file using the application's
driver.
Re-save the file in normal (non-compressed)
PDF format.
Some types of High Compression PDF files are
not supported. Consult your sales representative about the supported file types.
[PDF Direct Print] produces strange or malformed characters.
Fonts were not embedded.
Embed fonts in the PDF file you want to print
and then print.
If the problem cannot be solved, contact your service representative.
44
4. Troubleshooting When
Using the Scanner Function
This chapter explains likely causes of and possible solutions for scanner function
problems.
When Scanning is Not Done as Expected
This section explains causes and remedies when scan results are not as expected.
Problem
Cause
Solution
The scanned image is
dirty.
The exposure glass or ADF is
dirty.
Clean these parts. See p.107
“Maintaining Your Machine”.
The image is distorted
or out of position.
The original was moved during
scanning.
Do not move the original during
scanning.
The image is distorted
or out of position.
The original was not pressed flat
against the exposure glass.
Make sure that the original is
pressed flat against the exposure
glass.
The scanned image is
upside down.
The original was placed upside
down.
Place the original in the correct
orientation. See “Placing Originals”, Copy/Document Server
Reference.
No image results from
scanning.
The original was placed with the
front and back reversed.
When the original is placed directly on the exposure glass, the
side to be scanned must face
down. When the original is fed
via the ADF, the side to be
scanned must face up. See “Placing Originals”, Copy/Document
Server Reference.
Images are scanned in
rotated.
If you set the original with its up- When placing a stack of originals
per edge backward and save full in the ADF, place their lower edgcolor/grey scale images as a TIFF es first.
or JPEG file, they are scanned in
rotated.
The scanned image
contains white spaces.
• If you scan originals using
functions other than the network TWAIN scanner function, certain paper size and
resolution settings may produce scanned images that are
larger than the specified size
because of margins being
added to the sides.
Scanning at a higher resolution
may reduce the margins.
• If the Printer/Scanner Unit
(optional ) is installed, the
margins may become wider.
45
Troubleshooting When Using the Scanner Function
When You Cannot Send Scanned Files
The following sections explain likely causes of and solutions for Network Delivery and E-mail Sending-related problems.
When Stored Files Cannot be Accessed
This section explains likely causes of and possible solutions for job access-related problems.
Problem
The stored file is locked
and is not accessible.
4
Cause
Solution
The file, which is password pro- Contact the administrator.
tected, is locked because the password was incorrectly entered ten
times.
When You Cannot Browse the Network to Send a Scan file
This section explains likely causes of and possible solutions for the Browse Network failing to operate when files are sent.
Problem
Cause
The network cannot be The following machine settings
browsed when specify- may not be correct:
ing the destination fold- • IPv4 address
er.
• Subnet Mask
Solution
Check the settings. See “Network
Settings ”, General Settings
Guide.
When the TWAIN Driver Cannot be Started
This section explains likely causes of and possible solutions for the TWAIN driver failing to operate.
46
Problem
Cause
Solution
The Scanner Properties
dialog box cannot be
displayed.
Advanced encryption has been
specified in the extended security
setting.
For details about the extended security setting, contact an administrator.
When You Cannot Send Scanned Files
When Stored Files Cannot be Edited
This section explains likely causes of and possible solutions for the TWAIN driver failing to operate.
Problem
Cause
Stored files cannot be
deleted. File names and
passwords cannot be
changed. Files cannot
be redelivered.
Limits have been imposed using
the available extended security
function.
Solution
Contact the administrator.
Operations are not possible when messages appear
4
This section explains likely causes of and possible solutions for messages that
appear and when the machine fails to operate.
Message
Cause
Solution
Destination list
/ machine settings are updated. Selected
destinations or
function settings have been
cleared. Please
re-select the
settings.
The destination list is being updated from the network using
SmartDeviceMonitor for Admin.
Depending on the number of destinations to be updated, there
may be some delay before you
can resume operation. Operations are not possible while this
message is displayed.
Wait until the message disappears. Do not switch off the power while this message is
displayed.
47
Troubleshooting When Using the Scanner Function
When a Message is Displayed
This section explains likely causes of and possible solutions for error messages
that may appear on the machine's control panel.
When a Message is Displayed on the Control Panel
This section explains causes and remedies if an error message appears on the
display of the control panel.
Important
❒ If a message not described here appears, act according to the message. For information about how to turn off the main power switch, see About This Machine.
4
Message
Cause
Solution
Connection with
LDAP server has
failed. Check the
server status.
A network error has occurred and connection
has failed. Try the operation once more.
Try the operation once more. If the message is still shown, the network may be
crowded. Check the information of System Settings. See “System Settings”,
General Settings Guide.
LDAP server authentication has
failed. Check the
settings.
The user name and pass- Make settings correctly for the user
word differ from those
name and the password for LDAP servset for LDAP Authentica- er authentication.
tion.
Updating the des- A network error has octination list has curred.
failed. Try
again?
Check whether the server is connected.
A network error has ocThe destination
list has been up- curred.
dated. Specified
destination(s) or
sender's name has
been cleared.
If a destination or sender's name was already selected, re-select it after this
message disappears.
Exceeded max.
number of files
which can be sent
at the same time.
Reduce the number
of the selected
files.
48
The number of files exceeded the maximum
number possible.
Reduce the number of files and send
them again.
When a Message is Displayed
Message
Cause
Solution
Cannot detect
original size.
Place original
again, then press
the Start key.
You have loaded paper of
a size not shown on the
paper size selector.
• Place the original correctly.
Exceeded max. No.
of results to
display. Max.:
Search results have exceeded the max. displayable number.
Search again after changing the search
conditions.
You do not have
the privileges to
use this function.
The machine has not been Contact the administrator.
set to allow you to use the
function.
Exceeded max.
number of standby
files.Try again
after the current
file is sent.
The maximum number of There are 100 files waiting in the sendstandby files was exceed- ing queue for e-mail, Scan to Folder, or
ed.
delivery functions. Wait until files have
been sent.
Exceeded time
limit for LDAP
server search.
Check the server
status.
A network error has occurred and connection
has failed.
Try the operation once more. If the message is still shown, the network may be
crowded. Check the information of System Settings. See “System Settings”,
General Settings Guide.
The specified
group contains
some destination(s) that do
not have access
privileges. Do
you want to select only the
privileged destination(s)?
The specified group contains some destinations
for sending by e-mail and
some destinations for
sending by Scan to Folder.
To select destinations for sending by email, press [Select] for the message displayed on the e-mail screen. To select
destination for sending by Scan to Folder, press [Select] for the message displayed on the Scan to Folder screen.
Cannot find the
specified path.
Please check the
settings.
The destination computer name or folder name is
invalid.
Check whether the computer name and
the folder name for the destination are
correct.
Exceeded max.
number of alphanumeric characters for the
path.
The maximum number of
specifiable alphanumeric
characters in a path has
been exceeded.
The maximum number of characters
which can be entered for the path is 128.
Check the number of character you entered, and then enter the path again.
See “Transmission function”, Scanner
Reference.
• Specify the scan size.
• When placing an original directly
on the exposure glass, the lifting/
lowering action of the ADF triggers
the automatic original size detection
process. Lift the ADF by more than
30 degrees. See “Placing Originals”,
Copy/Document Server Reference.
4
49
Troubleshooting When Using the Scanner Function
Message
4
Cause
Solution
You have tried to delete
The selected
file(s) contained files without the authority to do so.
file(s) without
access privileges. Only file(s)
with access privileges will be
deleted.
The files can be deleted by the file administrator. To delete a file which you
are not authorized to delete, contact the
administrator.
Some of selected
files are currently in use.
They could not be
deleted.
You cannot delete a file
which is waiting to be
transmitted (“Waiting...”
status displayed) or
whose information is being changed with DeskTopBinder.
Cancel transmission (“Waiting...”status
cleared) or the DeskTopBinder setting,
and then delete the file.
Selected file is
currently in use.
Cannot change
file name.
You cannot change the
name of a file whose status is “Waiting...” or that
is being edited with
DeskTopBinder.
Change the file name after canceling
delivery or completing editing.
Selected file is
currently in use.
Cannot change
password.
You cannot change the
name of a file whose status is “Waiting...” or that
is being edited with
DeskTopBinder.
Delete the password after canceling delivery or completing editing.
Selected file is
currently in use.
Cannot change
user name.
You cannot change the
password of a file whose
status is “Waiting...” or
that is being edited with
DeskTopBinder.
A sender's name should be specified
before sending e-mail. Send e-mail after
specifying the sender's name.
Connection with
the destination
has failed. Check
the status and
connection. To
check the current
status, press
[Scanned Files
Status].
The correct Network settings are not made.
• Check the network settings of the
client computer.
• Check that components such as the
LAN cable are connected properly.
• Check that the server settings are
correct and the server is working
properly.
The entered user name or • Check that the user name and passAuthentication
word are correct.
with the destina- password was invalid.
tion has failed.
• Check that the ID and password for
the destination folder are correct.
Check settings.
To check the cur• A password of 128 or more characrent status,
ters may not be recognized.
press [Scanned
Files Status].
50
When a Message is Displayed
Message
Sender has not
been specified.
Cause
The sender's name was
not specified.
Exceeded max. E- The maximum e-mail size
mail size. Send- has been exceeded.
ing E-mail has
been cancelled.
Check [Max. Email Size] in
Scanner Features.
Solution
A sender's name should be specified
before sending e-mail. Send e-mail after
specifying the sender's name.
• Increase the size of [Max. E-mail Size].
• Set [Divide & Send E-mail] to [Yes (per
Page)] or [Yes (per Max. Size)].
See “Send Settings”, General Settings
Guide.
Sending the data
has failed. The
data will be resent later.
A network error has occurred and a file was not
sent correctly.
Wait until sending is retried automatically after the preset interval. If sending
fails again, contact the administrator.
Transmission has
failed. To check
the current status, press
[Scanned Files
Status].
While a file was being
sent, a network error occurred and the file could
not be sent correctly.
Try the operation once more. If the message is still shown, the network may be
crowded. Contact the administrator. If
multiple files were sent, use the
Scanned Files Status screen to check for
which file the problem occurred.
Transmission has
failed. Insufficient memory in
the destination
hard disk. To
check the current
status, press
[Scanned Files
Status].
Transmission has failed. Allocate sufficient space.
There was not enough
free space on the hard
disk of the SMTP server,
FTP server, or client computer at the destination.
Output buffer is
full. Sending the
data has been
cancelled. Please
try again later.
The file being stored has
exceeded the max. number of pages for one file.
Specify whether to use the data or not.
Scan the pages that were not scanned
and store them as a new file. See Storing
Files Using the Scanner Function Scanner Reference.
Exceeded maximum
number of file to
store. Delete all
unnecessary
files.
Too many files are waiting to be delivered.
Please try again after they have been
delivered.
Too many files are waitExceeded max.
number of stored ing to be delivered.
files. Cannot
send the scanned
data as capturing
files is unavailable.
Please try again after they have been
delivered.
4
51
Troubleshooting When Using the Scanner Function
4
Message
Cause
Solution
Exceeded max.
number of files
which can be used
in Document Server at the same
time.
The maximum number of
files that can be stored in
the document server has
been exceeded.
Check the files stored by the other functions, and then delete unneeded files.
See “Document Server”, Copy/Document Server Reference.
Entered protection code for
destination is
incorrect. Please
re-enter.
The correct protect destination code was not entered.
Make sure the protection code is correct, and then enter it again. See “Registering a Protection Code”, General
Settings Guide.
Entered user code
is not correct.
The entered user code is
incorrect.
Check the authentication setting, and
then specify a correct user code.
Exceeded max.
number of alphanumeric characters.
The maximum enterable
number of alphanumeric
characters has been exceeded.
Make sure the maximum number of
characters which can be entered, and
then enter it again. See “Values of various set items for transmission/storage
function”, Scanner Reference.
Authentication
has failed.
The entered login user
name or login password
is incorrect.
Check the login user name and login
password. The machine is unable to authenticate. Contact an administrator.
The entered path
is not correct.
Please re-enter.
The entered path format
is incorrect.
Confirm the destination computer and
the path, and then enter it again.
Captured file ex- The maximum number of
ceeded max. num- pages per file has been
ber of pages per exceeded.
file. Cannot send
the scanned data.
Reduce the number of pages in the
transmitted file, and then resend the
file. See “Storage function”, Scanner
Reference.
Original is being The machine is using an- Retry scanning after the operation with
the other function is completed.
scanned by anoth- other function such as
copying.
er function.
Please wait.
[Copier][Document Server]...
52
E-mail address
entered is not
correct. Please
re-enter.
The entered e-mail address is incorrect.
Make sure the e-mail address is correct,
and then enter it again.
Memory is full.
Scanning has been
cancelled. Press
[Send] to send
the scanned data,
or press [Cancel]
to delete.
Because there is not
enough free hard disk
space in the machine for
delivering or sending by
e-mail while storing in
the Document Server,
only some of the pages
could be scanned.
Specify whether to use the data or not.
When a Message is Displayed
Message
Cause
Memory is full.
Cannot scan. The
scanned data will
be deleted.
Because of insufficient
hard disk space, the first
page could not be
scanned.
Solution
Try one of the following measures:
• Wait for a while, and then retry the
scan operation.
• Reduce the scan area or scanning
resolution. See “Setting items for
Scan Settings”, Scanner Reference.
• Delete unneeded stored files. See
“Deleting a Stored File”, Scanner
Reference.
Memory is full.
Do you want to
store scanned
file?
Because there is not
enough free hard disk
space in the machine for
storing in the Document
Server, only some of the
pages could be scanned.
No paper is set in the
No paper. Load
specified paper tray.
paper of one of
the following
sizes, then press
[Start Printing].
Specify whether to use the data or not.
4
Load paper of the sizes listed in the
message.
Exceeded max.
data capacity.Check the
scanning resolution, then reset
original(s).
The scanned original exceeded maximum data
capacity.
Exceeded max.
data capacity.Check scanning
resolution, then
press Start key
again.
The scanned data exceed- Specify the scan size and resolution
ed maximum data capac- again. Note that it may not be possible
ity.
to scan very large originals at a high
resolution. See “Relationship between
Resolution and File Size”, Scanner Reference.
Exceeded max.
page capacity per
file. Press
[Send] to send
the scanned data,
or press [Cancel]
to delete.
The number of scanned
pages exceeded maximum page capacity.
Specify the scan size and resolution
again. Note that it may not be possible
to scan very large originals at a high
resolution. See “Relationship between
Resolution and File Size”, Scanner Reference.
Select whether to send the data so far.
53
Troubleshooting When Using the Scanner Function
When a Message is Displayed on the Client Computer
This section explains likely causes of and possible solutions for the main error
messages displayed on the client computer when using the TWAIN driver.
Important
❒ If a message not described here appears, act according to the message. For information about how to turn off the main power switch, see About This Machine.
Message
Clear Misfeed(s)
in ADF.
Cause
A paper misfeed has occurred inside the ADF.
Solution
Remove jammed originals, and place
them again.
Check whether the originals are suitable to be scanned by the machine.
4
54
Invalid Winsock
version. Please
use version 1.1
or higher.
You are using an invalid
version of Winsock.
Install the operating system of the computer or copy Winsock from the operating system CD-ROM.
The name is already in use.
Check the registered names.
You tried to register a
name that is already in
use.
Use another name.
Cannot detect the
paper size of the
original. Specify
the scanning
size.
The set original was misaligned.
• Place the original correctly.
Cannot add any
more scanning
mode.
The maximum number of
registerable scan modes
has been exceeded.
The maximum number of modes that
can be stored is 100. Delete unneeded
modes.
Cannot specify
any more scanning
area.
The maximum number of
registerable scan areas
has been exceeded.
The maximum number of scanning areas that can be stored is 100. Delete unneeded scanning area.
• Specify the scan size.
• When placing an original directly
on the exposure glass, the lifting/lowering action of the ADF
triggers the automatic original size
detection process. Lift the ADF by
more than 30 degrees.
An unrecoverable error
Call Service
Please call your has occurred in the maservice represen- chine.
tative.
Call your service representative.
The TWAIN scanner
Scanner is not
available on the function cannot be used
specified device. on this machine.
Contact your service representative.
When a Message is Displayed
Message
Scanner is not
available. Check
the scanner connection status.
Cause
• The machine's main
power switch is off.
• The machine is not
connected to the network correctly.
Solution
• Set the main power switch to “On”.
• Check whether the machine is connected to the network correctly.
• Deselect the personal firewall function of the client computer.
• Use an application such as telnet to
make sure SNMPv1 or SNMPv2 is
set as the machine’s protocol. See
“Network Settings”, General Settings Guide and “Using telnet”,
Network Guide.
No response from
the scanner.
The machine or client
Check whether the machine or client
computer is not connected computer is connected to the network
to the network correctly. correctly.
No response from
the scanner.
The network is crowded.
Wait for a while, and then try to reconnect.
Error has occurred in the
scanner.
The application-specified scan conditions have
exceeded the setting
range of the machine.
Check whether the scanning settings
made with the application exceed the
setting range of the machine.
Fatal error has
occurred in the
scanner.
An unrecoverable error
has occurred on the machine.
An unrecoverable error has occurred in
the machine. Call your service representative.
Cannot connect to
the scanner.
Check the network
Access Mask settings in User
Tools.
An access mask is set.
Contact the network or scanner administrator.
Scanner is not
ready. Check the
scanner and the
options.
The ADF cover is open.
Check whether the ADF cover is closed.
4
Insufficient mem- Scanner memory is insuf- • Reset the scan size.
ficient.
ory. Reduce the
• Lower the resolution.
scanning area.
• Set with no compression. See
TWAIN Driver help.
The problem may be due to the following cause:
• Scanning cannot be performed if
large values are set for brightness
when using halftone or high resolution. See “Relationship between
Resolution and Original Size”, Scanner Reference.
55
Troubleshooting When Using the Scanner Function
Message
Cause
Cannot find "XXX"
scanner used for
the previous
scan. "YYY" will
be used instead.
• The main power
switch of the previously used scanner is
not set to “On”.
(“XXX” and “YYY” indicate scanner names.)
• The machine is not
connected to the network correctly.
Solution
• Check whether the main power
switch of the scanner used for the
previous scan is turned off.
• Check the previously used scanner is
connected to the network correctly.
• Cancel the Personal Firewall of the
client computer.
• Use an application such as telnet to
make sure SNMPv1 or SNMPv2 is
set as the machine’s protocol. See
“Network Settings”, General Settings Guide and “Using telnet”,
Network Guide.
4
• Select the scanner used for the previous scan.
Error has occurred in the
scanner driver.
An error has occurred in
the driver.
• Check whether the network cable is
connected correctly to the client
computer.
• Check whether the Ethernet board
of the client computer is recognized
correctly by Windows.
• Check whether the client computer
can use the TCP/IP protocol.
Communication er- A communication error
ror has occurred has occurred on the network.
on the network.
Scanner is in use
for other function. Please
wait.
A function of the machine
other than the scanner
function is being used
such as the copier function.
Insufficient mem- Memory is insufficient.
ory. Close all
other applications, then restart scanning.
56
Check whether the client computer can
use the TCP/IP protocol.
Wait for a while and reconnect.
• Close all the unnecessary applications running on the client computer.
• Uninstall the TWAIN driver, and
then reinstall it after restarting the
computer.
No User Code is
registered. Consult your system
administrator.
Access is restricted with
user codes.
Contact the administrator of the machine.
Any of Login User
Name, Login Password or Driver
Encryption Key is
incorrect.
The entered login user
• Check the login user name, login
name, password, or drivpassword, and driver encryption
er encryption key was inkey.
valid.
• Permission to use this function has
not been granted. Contact the administrator.
When a Message is Displayed
Message
Cause
Solution
Cannot register
the user because
the scanner's address book is
full.
Failed to authenticate the
user at the authentication
server because the address book is full.
Contact the administrator of the machine.
The user has been
already registered in the
scanner's address
book.
Failed to authenticate the
user at the authentication
server because same user
name has been already
registered in the address
book.
Contact the administrator of the machine.
4
57
Troubleshooting When Using the Scanner Function
4
58
5. Adding paper, Toner and
Staples
This chapter explains troubleshooting procedures that are applicable to all the
machine's functions.
Loading paper
This section explains what to do when paper runs out and needs reloading.
R CAUTION:
• When loading paper, take care not to trap or injure your fingers.
Note
❒ Fan the paper before loading.
❒ Straighten curled or warped paper before loading.
❒ When paper in trays that are set to automatically eject unnecessary tab stock
sheets runs out, reload the tab stock from the beginning of the cycle (the first
sheet).
❒ For paper types and sizes, see “Recommended Paper Sizes and Types”,
About This Machine.
❒ To load paper in the multi bypass tray (Tray 7), see “Using the Multi Bypass
Tray (Tray 7)”, Copy/Document Server Reference.
Loading paper into Tray 1 (Tandem Tray)
The following procedure explains how to load paper into Tray 1.
Important
❒ When paper loaded in the right side of Tray 1 runs out, paper on the left is
automatically shifted to the right. While the paper is moving, a message instructing you to wait appears. Do not pull out the tray at this time.
❒ For the right stack, align the right edge of the copy paper with the right edge
of the tray. For the left stack, align the left edge of the copy paper to the left
edge of the tray.
❒ Tray 1 uses only letter size (81/2”×11”K) paper. If you want to load A4K,
contact your service representative.
❒ Do not stack paper over the limit mark.
59
Adding paper, Toner and Staples
A Carefully pull out the paper tray until it stops.
ANQ001S
B Square the paper and place it print side down.
• Whole tray pulled out
5
ANQ002S
• Left half of the tray pulled out
ANQ003S
C Carefully slide the paper tray fully in.
Note
❒ You can load paper even while making copies from Tray 1. You can pull
out the left half of the tray while copying is in.
❒ The tray can hold up to 1,000 sheets.
60
Loading paper
Loading Paper into the A3/11” × 17” Tray Unit
The following procedure explains how to load paper into the A3/11” × 17” tray
unit. To use the A3/11” × 17” tray unit, you must replace Tray 1.
Important
❒ Make sure that the paper stack is flush to the right side fence.
❒ Do not stack paper over the limit mark.
A Carefully pull out the paper tray until it stops.
5
ANQ008S
B Place the paper in the tray along the edge on the left.
ANQ009S
C Carefully slide the paper tray fully in.
Note
❒ The tray can hold up to 1,000 sheets.
61
Adding paper, Toner and Staples
Loading Paper into Tray 2 and 3
The following procedure explains how to load paper into Tray 2 and 3.
Important
❒ Various sizes of paper can be loaded in Tray 2 and 3 by adjusting the positions
of side fence and end fence.
❒ Check the paper edges are aligned at the right side.
❒ Do not stack paper over the limit mark.
A Carefully pull out the paper tray until it stops.
5
ANQ004S
B Square the paper and load it print side down.
ANQ005S
C Carefully slide the paper tray fully in.
Note
❒ If you load a paper size that is not selected automatically, you will need to
specify the paper size with the control panel.
❒ The tray can hold up to 500 sheets.
Reference
p.70 “Changing the Paper Size”
p.78 “Changing to a Size that is Not Automatically Detected”
62
Loading paper
Loading Paper into the Large Capacity Tray (LCT)
The following procedure explains loading paper into the large capacity tray
(LCT). The LCT is identified as Tray 4, Tray 5, and Tray 6.
Important
❒ Various sizes of paper can be loaded in Tray 4 and Tray 5 by adjusting the positions of side fence and end fence.
❒ If you want to change the paper size of Tray 6, contact your service representative.
❒ Check the paper's edges are aligned at the left side.
❒ Do not stack paper over the limit mark.
A Carefully pull out the paper tray until it stops.
5
ANQ006S
B Load paper into the paper tray by pushing it against to the left side of the
paper tray.
Load the paper print side up.
ANQ007S
C Carefully slide the paper tray fully in.
Note
❒ The tray can hold up to 1,000 sheets in Tray 4 and 5, and 2,550 sheets in
Tray 6.
63
Adding paper, Toner and Staples
Reference
p.70 “Changing the Paper Size”
p.78 “Changing to a Size that is Not Automatically Detected”
Loading Paper into the Wide Large Capacity Tray (Wide LCT)
The following procedure explains loading paper into the wide large capacity
tray (Wide LCT). The Wide LCT is identified as Tray 4, Tray 5, and Tray 6.
Important
❒ Various sizes of paper can be loaded in the Wide LCT by adjusting the positions of side fence and end fence.
❒ Check that the paper edges are aligned at the left side.
❒ Do not load paper above the upper mark in the paper tray
A Carefully pull out the paper tray until it stops.
5
ANQ060S
B Load paper into the paper tray by pushing the paper to the left side of the
paper tray.
Place paper with printing side up.
ANQ065S
C Carefully slide the paper tray fully in.
64
Loading paper
Note
❒ The tray can hold up to 1,000 sheets in Tray 4 and 6, and 2,000 sheets in
Tray 5.
❒ If you load paper that cannot be automatically detected, specify its size using the control panel.
Reference
p.70 “Changing the Paper Size”
p.78 “Changing to a Size that is Not Automatically Detected”
Loading Paper into the Multi Bypass Tray (Tray 7)
The following procedure explains loading paper into the multi bypass tray (Tray 7).
Important
❒ Check that the paper edges are aligned at the left side.
5
❒ The maximum number of sheets you can load into the multi bypass tray (Tray
7) depend on paper type. The number should not exceed the upper limit.
A Set the side fence to the paper size.
APF028S
B Place paper in the multi bypass tray (Tray 7).
65
Adding paper, Toner and Staples
C Set the end fence.
ANQ068S
To remove the end fence, slide it to the right.
5
ANQ069S
D Press the elevator switch on the multi bypass tray (Tray 7).
APF030S
The green lamp of the elevator switch is blinking while the tray is going up
and down, and keeps lit when it stops.
Press the elevator switch to move down original table if you want to either
add paper or remove jammed ones.
Note
❒ The tray can hold up to 500 sheets.
❒ For details about using the multi bypass tray (Tray 7), see “Using the Multi
Bypass Tray (Tray 7)”, Copy/Document Server Reference.
66
Reference
p.78 “Changing to a Size that is Not Automatically Detected”
Loading paper
Loading Paper in the Interposer
The following procedure explains loading paper into the interposer.
Important
❒ Load paper on the side already printed (the front side). If you are using the
Booklet Finisher (Saddle Stitch), load sheets print side down.
❒ Load paper in the interposer in the same orientation as paper in the paper
tray.
❒ The staple or punching location will be on the left side of the paper, when you
are facing the machine.
❒ Do not place anything on top of or leave documents on the sensor. This may
lead to the paper size not being correctly scanned or paper jams.
❒ When using the Z-fold function, the paper in the interposer must be of the
same size as the prints after they have been Z-folded. If the paper in the interposer is larger than the Z-folded sheets, a misfeed might occur.
5
A While pressing the release lever, align the side fence with the paper size to
be loaded.
ANQ010S
B Load paper orderly. Tightly fit the side fence to the loaded paper.
ANQ012S
C When loading paper larger than A4, draw out the paper extender.
67
Adding paper, Toner and Staples
Note
❒ To set the paper in the interposer, align the orientation of originals in the
ADF as shown below.
ANR026S
❒ When paper is loaded which cannot be detected automatically, the user
must set the paper size on the control panel.
5
Reference
p.78 “Changing to a Size that is Not Automatically Detected”
Orientation-Fixed Paper or Two-Sided Paper
The following describes paper with its orientation and printing surface specified
(letterhead paper).
Orientation-fixed (top to bottom) or two-sided paper (for example, letterhead
paper, punched paper, or copied paper) might not print correctly, depending on
how the originals and paper are placed. Select [On] in [Letterhead Setting] under
[Copier / Document Server Features], and then place the original and paper as
shown below. See “Letterhead Setting”, General Settings Guide. When printing
with the printer function, placement orientation is the same.
For printing using the printer function, load paper in the same orientation.
68
Loading paper
❖ Paper orientation
5
Note
❒ Press the {Tray Paper Setting} key, specify Letterhead as “Paper Type” for the
paper tray you want to use. See “Tray Paper Settings”, General Settings
Guide.
69
Adding paper, Toner and Staples
Changing the Paper Size
This section explains how to change a paper size.
Procedures for changing the paper size differ depending on the tray (tray 1 or
other optional paper tray units). Make sure you are following the appropriate
procedure before you begin.
Note
❒ Be sure to select the paper size with User Tools. If you do not, misfeeds might
occur.
❒ Fan the paper before loading.
❒ Straighten curled or warped paper before loading.
❒ For details about paper sizes and types, see “Copy Paper”, About This Machine.
5
Changing the Paper Size in Tray 2 and 3
The following procedure explains how to change a paper size in Tray 2 and 3.
Important
❒ If a paper tray is pushed vigorously when putting it back into place, the position of the tray's side fence may slip out of place.
❒ Check that the paper edges are aligned at the right side.
❒ Do not stack paper over the limit mark.
A Check that paper in the paper tray is not being used for copying, and then
pull the tray carefully out until it stops.
ANQ014S
B Remove paper if loaded.
70
Changing the Paper Size
C Release the lock on the side fence.
ANQ015S
D While pressing down the release lever, slide the side fences until they are
aligned the paper size you want to load.
5
ANQ016S
E Slide the end fence until it is aligned with the size of paper to you want to
load.
ANQ017S
71
Adding paper, Toner and Staples
F Square the paper and load it print side up.
Re-lock the side fences again.
ANQ018S
G Carefully slide the paper tray fully in.
H Check the size on the display.
5
Note
❒ If there is space between the side fence and paper, bring the side fence
flush against the edge of the paper.
Changing the Paper Size in the Large Capacity Tray (Tray 4 and 5)
The following procedure explains how to change a paper size in the LCT (Tray
4 and 5).
Important
❒ As for changing paper sizes of Tray 6, contact your service representative.
❒ Check that the paper edges are aligned at the left side.
❒ Do not stack paper over the limit mark.
A Carefully pull out the paper tray until it stops.
ANQ006S
72
Changing the Paper Size
B Pull out the screws fixing the side fence.
ANQ020S
C Set the side fences to the size you want.
5
ANQ021S
D Fasten the side fence with the screws.
ANQ022S
73
Adding paper, Toner and Staples
E Set the end fence along the paper size.
ANQ023S
F Square the paper and set it in the tray.
5
ANQ024S
G Set the paper size selector in the innermost part of the tray to the new paper
size.
ANQ025S
H Carefully slide the paper tray fully in.
I Check the size on the display.
74
Changing the Paper Size
Load A4K, 81/2” × 11”K into the Large Capacity Tray (Tray 4 and 5)
Follow the procedure below to set the end fence for A4K, 81/2” × 11”K.
A Set the end fence according to the paper size.
ANQ076S
A
B
A4K
81/2” × 11”K
5
B Fasten the end fence using the screw provided.
ANQ077S
Note
❒ When loading index tabs, shift the end fence for A4K, 81/2” × 11”Kto position before setting the end fence for index tabs.
75
Adding paper, Toner and Staples
Changing the Paper Size in the Wide Large Capacity Tray
The following procedure explains how to change a paper size in the wide large
capacity tray (Wide LCT).
Important
❒ Check that the paper edges are aligned at the left side.
❒ Do not stack paper over the limit mark.
A Carefully pull out the paper tray until it stops.
5
ANQ060S
B Pull out the screws fixing the side fence.
ANQ061S
C Take the grip of the side fence with your fingers, and adjust the side fence
to the paper size.
ANQ062S
76
Changing the Paper Size
D Fasten the side fence with the screws.
ANQ063S
E Release the lock on the back fence.
5
ANQ064S
F Square the paper and set it in the tray.
ANQ066S
77
Adding paper, Toner and Staples
G Tightly fit the back fence to the loaded paper and then re-lock the back
fence again.
ANQ067S
H Carefully slide the paper tray fully in.
I Check the size on the display.
5
Changing to a Size that is Not Automatically Detected
If you load a paper size that is not selected automatically, you need to specify the
paper size with the control panel. This section explains how to load these paper
taking 11”× 15”L as an example.
Important
❒ Following paper sizes that are not selected automatically.
• Tray 2, Tray 3:
11” × 15”L, 11” × 14”L, 10” × 15”L, 10” × 14”L, 81/4” × 14”L, 8” × 10”L
• Tray 4, Tray 5, Tray 6 (Wide LCT):
A4L, B5L, A5K, B6L, A6L, 81/2” × 14”L, 81/2” × 13”L, 81/4” × 13”L,
101/2” × 71/4”KL, 11” × 15”L, 10” × 14”L, 81/4” × 14”L
• Multi Bypass Tray (Tray 7), Interposer:
A4L, B5L, A5K, B6L, 81/2” × 14”L, 81/2” × 13”L, 81/4” × 13”L,
101/2” × 71/4”KL, 11” × 15”L, 10” × 14”L, 81/4” × 14”L, 8” × 10”L
A Press the {Tray Paper Setting} key.
ANR102S
78
The Tray Paper Settings screen appears.
Changing the Paper Size
B Select the tray number on the screen.
C Press [Paper Size] tab.
5
D Select a combination of the specified paper size and orientation, and then
press [OK].
The paper size and orientation appear.
79
Adding paper, Toner and Staples
E Press the {Tray Paper Setting} key.
The initial display is shown.
Note
❒ If you want to print on paper that is selected automatically after printing
on a paper size that is not selected automatically, you must return the setting to “Auto Detect”. Reload the paper, select “Auto Detect” in step D. The
setting is returned to “Auto Detect”.
5
80
Pausing Copy When Using Finisher
Pausing Copy When Using Finisher
You can pause a large volume of copies when using Finisher.
A Press the {Suspend/Resume} key.
The key lights up.
ANQ082S
5
B Remove the stack of paper from the finisher shift tray.
ANQ083S
C Press the {Suspend/Resume} key.
The key turns off, and then copying restarts.
Note
❒ You can suspend copy only when the output tray is specified as the finisher shift tray.
81
Adding paper, Toner and Staples
Adding Toner
This section explains adding and storing toner.
R WARNING:
• Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers
in accordance with local regulations.
R CAUTION:
• Keep toner (used or unused) and toner containers out of reach of children.
R CAUTION:
• If toner or used toner is inhaled, gargle with plenty of water and move into a
fresh air environment. Consult a doctor if necessary.
R CAUTION:
• If toner or used toner gets into your eyes, flush immediately with large
amounts of water. Consult a doctor if necessary.
5
R CAUTION:
• If toner or used toner is swallowed, dilute by drinking a large amount of water. Consult a doctor if necessary.
R CAUTION:
• Avoid getting toner on your clothes or skin when removing a paper jam or
replacing toner. If your skin comes into contact with toner, wash the affected
area thoroughly with soap and water.
• If toner gets on your clothing, wash with cold water. Hot water will set the
toner into the fabric and may make removing the stain impossible.
R CAUTION:
• Our products are engineered to meet high standards of quality and functionality, and we recommend that you use only the expendable supplies available at an authorized dealer.
R CAUTION:
• Do not open toner containers forcefully. Toner can spill, dirtying your clothes
or hands, and possibly resulting in accidental ingestion.
82
Important
❒ Faults may occur if you use toner other than the recommended type.
❒ When adding toner, do not turn off the operation switch. If you do, settings
will be lost.
❒ Always add toner when the machine instructs you.
❒ Do not use recycled toner. This will damage the machine.
❒ During toner adding, the toner bottle is rotating. Do not touch the toner bottle.
Adding Toner
❒ If toner remains in the bottle, you cannot remove the bottle. Do not remove
the bottle forcibly.
❒ Be sure to set the new toner bottle in the lower hole first.
❒ Store toner containers in a cool, dry place free from direct sunlight.
❒ Store toner on a flat surface.
Note
❒ If both toner bottles are empty, D will appear.
❒ You can still make about 200 copies after D appears, but replace the toner early to copy degradation.
❒ If one of the toner bottle is empty, you can keep copying by using the other
bottle.
❒ You can change the toner bottle during copying.
❒ If toner remains in the bottle, you cannot pull it out.
❒ When you change one toner bottle, do not touch the other one.
❒ Press [System Status] to check contact number for consumables' order. For system status, see p.5 “Checking Machine Status and Settings”.
5
83
Adding paper, Toner and Staples
Inserting Toner
The following describes how to replace toner.
Important
❒ Do not shake the toner bottle with its mouth down after removing it. Residual
toner may scatter.
5
ANR001S
Used Toner
Toner cannot be re-used.
Bring the stored used container to your sales representative or service representative for recycling through our recycling system. Or, dispose of the stored used
container in accordance with the local regulations.
84
Adding Staples
Adding Staples
This section explains what to do when staples need replacing.
R CAUTION:
• Keep your hands clear of the booklet finisher tray when pulling out or pushing in the finisher's staple unit. You can trap your fingers if you do not.
Important
❒ Stapling failures or jams may occur if you use a staple cartridge other than
that recommended.
Refill the stapler according to the finisher type. (Check the type if you are unsure.) For details about type of finisher, see “Options”, About This Machine.
Finisher
5
The following procedure explains how to add staples to the Finisher.
ANR002S
85
Adding paper, Toner and Staples
Booklet Finisher (Saddle Stitch)
The following procedure explains how to add staples to the Booklet Finisher.
5
ANR003S
86
6. Clearing Misfeeds
This chapter explains what to do when paper or originals misfeed (become
jammed inside the machine).
Removing Jammed Paper
R CAUTION:
• The inside of the machine could be very hot. Do not touch any parts other
than specified in this document when removing misfed paper. Otherwise, it
may cause burn injury.
R CAUTION:
• The fusing section of this machine might be very hot. Caution should be taken when removing misfed paper.
R CAUTION:
• Keep your hands clear of the booklet finisher tray when pulling out or pushing in the finisher's staple unit. You can trap your fingers if you do not.
Important
❒ When clearing misfeeds, do not turn off the operation switch. If you do, your
copy settings will be lost.
❒ To prevent misfeeds, do not leave any torn scraps of paper inside the machine.
❒ Remove the fusing unit only when necessary.
❒ Contact your service representative if misfeeds occur frequently.
Note
❒ For details about how to locate and remove misfeeds, see “Checking Jammed
Paper” or “Removing Jammed Paper”.
Reference
p.88 “Locating Jammed Paper”.
p.90 “Removing Jammed Paper”.
87
Clearing Misfeeds
Locating Jammed Paper
If a misfeed happens, remove the misfed paper or original following the procedures stated on the sticker on the rear of main unit front cover.
A misfeed has occurred in the place corresponding to the letter displayed on the
control panel.
6
ANQ030S
A Press the key of the section from where you want to remove the jammed paper.
88
Removing Jammed Paper
B After each step is complete, press [Next]. To go back to the previous step,
press [Previous].
C Press [Entire View], the entire machine is displayed.
6
D When all jammed paper are removed, restore the machine to the original
state.
Note
❒ More than one misfeed may be indicated. When this happens, check all the
areas indicated.
89
Clearing Misfeeds
Removing Jammed Paper
The following procedure explains how to remove jammed paper.
Important
❒ The fusing section of this machine might be very hot. Caution should be taken
when removing misfed paper.
❒ When removing jammed sheets, take care to touch only those areas explicitly
indicated in the manual.
❒ Do not remove the fusing unit. Doing so will result in loss of print quality.
Note
❒ Your machine might differ from that shown in these illustrations, depending
on the options installed on it.
• When A is lit
6
ANR004S
• When B1 is lit
• When B4 is lit
ANR006S
90
Removing Jammed Paper
• When C is lit
ANR007S
• When D is lit
6
91
Clearing Misfeeds
• When M is lit (when Booklet Finisher is installed)
6
ANR018S
92
Removing Jammed Paper
ANR019S
• When N1 is lit (when Z-Folding Unit is installed)
6
ANS008S
• When N2 or N3 is lit (when Z-Folding Unit is installed)
ANS009S
93
Clearing Misfeeds
• When P1 is lit (when ADF is installed)
ANR011S
• When P2 is lit (when ADF is installed)
ANR027S
6
• When Q1 or Q2 is lit (when Interposer is installed)
ANR016S
94
Removing Jammed Paper
• When Q3 or Q4 is lit (when Interposer is installed)
ANR017S
6
95
Clearing Misfeeds
• When R is lit (when Finisher is installed)
6
ANR021S
96
Removing Jammed Paper
• When U is lit (when Large Capacity Tray is installed)
ANR012S
6
• When U is lit (when Wide Large Capacity Tray is installed)
ANR013S
97
Clearing Misfeeds
• When V is lit (when Multi Bypass Tray (Tray 7) is installed)
ANR020S
• When Z1 is lit
6
ANR009S
• When Z4 is lit
ANR010S
98
Removing Jammed Paper
Note
❒ Inside the finisher, or inside the front cover, there is a sticker explaining how
to remove misfed paper.
❒ If a detailed removal instruction appears on the right of the screen, follow it.
❒ You can also use the procedure indicated in [System Status] to remove jammed
paper.
When Z-folded paper is not properly aligned
The following procedure explains when Z-folded copies are not properly
aligned.
A Press the {Suspend/Resume} key.
The key lights up.
6
ANQ082S
B Remove the copies.
C Set the auxiliary tray for the finisher shift tray.
ANQ075S
99
Clearing Misfeeds
Removing Jammed Staples
This section explains how to remove jammed staples.
R CAUTION:
• Keep your hands clear of the booklet finisher tray when pulling out or pushing in the finisher's staple unit. You can trap your fingers if you do not.
Important
❒ Curled paper may cause staples to jam. To avoid this, turn copy paper over
in the tray.
❒ When the finisher is installed, after removing jammed staples, staples will not
be ejected the first few times you try to use the stapler.
Remove the jammed staples according to the finisher type. (Check the type if
you are unsure.) For details about type of finisher, see “Options”, About This
Machine.
Finisher
6
The following procedure explains how to remove jammed staples from the Finisher.
100
ANR022S
Removing Jammed Staples
Booklet Finisher (Saddle Stitch)
The following procedure explains how to remove jammed staples from the
Booklet Finisher.
6
ANR023S
101
Clearing Misfeeds
Removing Punch and Staple Waste
This section explains how to remove punch and staple waste.
Note
❒ While “Hole Punch Receptacle is full.” or “Waste Staple Receptacle is full.” is displayed, you cannot use the Punch function or the Staple
function.
Finisher
The following procedure explains how to remove punch and staple wastes from
the Finisher.
• Remove punch wastes
6
ANR025
• Remove staple wastes
ANR024
Note
❒ If the message is still displayed, reinstall the waste box.
102
7. Remarks
This chapter describes how to maintain and operate the machine.
Where to Put Your Machine
This section provides precautions for installation, movement and disposal.
Machine Environment
Choose your machine's location carefully.
Environmental conditions greatly affect its performance.
Optimum environmental conditions
The following describes precautions when locating the machine.
R CAUTION:
• Keep the machine away from humidity and dust. Otherwise a fire or an electric shock might occur.
• Do not place the machine on an unstable or tilted surface. If it topples over,
an injury might occur.
R CAUTION:
• After you move the machine, use the caster fixture to fix it in place. Otherwise the machine might move or come down to cause an injury.
R CAUTION:
• Make sure the room where you are using the machine is well ventilated and
spacious. Good ventilation is especially important when the machine is used
heavily.
Temperature: 10-32 °C (50-89.6 °F) (humidity to be 54% at 32 °C, 89.6 °F)
Humidity: 15-80% (temperature to be 27 °C, 80.6 °F at 80%)
A strong and level base.
The machine must be level within 5 mm, 0.2 inches: both front to rear and left
to right.
• To avoid possible buildup of ozone, make sure to locate this machine in a
large well ventilated room that has an air turnover of more than 30
m3/hr/person.
•
•
•
•
103
Remarks
Environments to avoid
• Locations exposed to direct sunlight or other sources of strong light (more
than 1,500 lux).
• Locations directly exposed to cool air from an air conditioner or heated air
from a heater. (Sudden temperature changes can cause condensation to form
inside the machine.)
• Locations close to machines generating ammonia, such as a diazo copy machine.
• Places where the machine will be subject to frequent strong vibration.
• Dusty areas.
• Areas with corrosive gases.
Moving
The following describes precautions when moving the machine.
R CAUTION:
• Contact your service representative if you need to lift the machine (such as
when relocating it to another floor). Do not attempt to lift the machine without
the assistance of your service representative. The machine will be damaged
if it topples or is dropped, resulting in malfunction and risk of injury to users.
The machine's various handling areas are for service engineer use only. Do
not touch these areas.
7
R CAUTION:
• Before moving the machine, be sure to disconnect all external connections,
especially the power cord from the wall outlet. Damaged power cords are a
fire and electric shock hazard.
R CAUTION:
• Unplug the power cord from the wall outlet before you move the machine.
While moving the machine, you should take care that the power cord will not
be damaged under the machine.
Important
❒ Be careful when moving the machine. Take the following precautions:
• Turn off the main power.
• Unplug the power cord from the wall outlet. When you pull out the plug
from the socket, grip the plug to avoid damaging the cord, thereby reducing the risk of fire or electric shock.
• Close all covers and trays, including the front cover and bypass tray.
❒ Keep the machine level and carry it carefully, taking care not to jolt or tip it.
Rough handling may cause a malfunction or damage the hard disk or memory, resulting in loss of stored files.
104
Where to Put Your Machine
❒ Do not take off the holding stand.
❒ Protect the machine from strong shocks. Impact can damage the hard disk
and cause stored files to be lost. As a precautionary measure, files should be
copied to another computer.
Power Connection
The following explains power supply.
R WARNING:
• The supplied power cord is for use with this equipment only. Do not
use with other appliances. Doing so may result in fire, electric shock,
or injury.
R WARNING:
• Connect the machine only to the power source described on the inside
front cover of this manual. Connect the power cord directly into a wall
outlet and do not use an extension cord.
• Do not damage, break or make any modifications to the power cord.
Do not place heavy objects on it. Do not pull it hard nor bend it more
than necessary. These actions could cause an electric shock or fire.
R WARNING:
• If the power cord is damaged (exposure of the core, disconnection,
etc.), contact your service representative to change a new one. Operating the machine with a damaged power cord may cause an electric
shock or fire.
7
R WARNING:
• Pull out the plug from the outlet more than once a year to clean around
the prongs. Accumulating dust and dirt could cause a fire due to the
heat released by electric leakage.
R CAUTION:
• When you disconnect the power plug from the wall outlet, always pull the
plug (not the cable).
R CAUTION:
• To disconnect the power cord, pull it out by plug. Do not drag the code itself.
Doing so may result in damage to the code, leading to fire or electric shock.
R CAUTION:
• Be sure to fix the power cord securely so that no one trips over it.
• Make sure the plug is inserted firmly in the wall outlet.
• Voltage must not fluctuate by more than 10%.
• The wall outlet shall be installed near the machine and shall be easily accessible.
105
Remarks
Access to the Machine
Place the machine near the power source, providing the clearance areas shown.
1. Rear: more than 20 cm (7.8”)
2. Right: more than 3 cm (1.1”)
3. Front: more than 55.5 cm (21.6”)
4. Left: more than 40 cm (15.7”)
Note
❒ For the required space when options are installed, contact your service representative.
7
106
Maintaining Your Machine
Maintaining Your Machine
If the exposure glass or ADF belt is dirty, copy clarity may be reduced. Clean
these parts if they are dirty.
Important
❒ Do not use chemical cleaners or organic solvents, such as thinner or benzene.
If such substances get inside the machine or melt plastic parts, a failure might
occur.
❒ Do not clean parts other than those explicitly specified in this manual. Other
parts should only be cleaned by your service representative.
❖ How to maintain
Cleaning the machine Wipe the machine with a soft, damp cloth, and then
wipe it with a dry cloth to remove the water.
Cleaning the Exposure Glass
The following procedure explains how to clean the exposure glass.
7
ANQ080S
Wipe the surface of the exposure glass.
107
Remarks
Cleaning the Auto Document Feeder
The following procedure explains how to clean the ADF.
ANQ081S
Wipe the surface of the belt, moving it.
7
108
Earth Leakage Circuit Breaker
Earth Leakage Circuit Breaker
This section explains how to test the earth leakage circuit breaker. For details, see
“Guide to Components”, About This Machine.
R WARNING:
• Do not turn the earth leakage circuit breaker from the off to the on position. Otherwise it might lead to an electric shock, fire or smoke, or
cause the circuit breakers to trip.
To prevent electric shock this machine has an earth leakage circuit breaker. The
earth leakage circuit breaker is normally in the on position.
Once a month, check that it functions properly by following the procedure below.
Important
❒ If the earth leakage circuit breaker is not functioning normally, contact your
sales or service representative.
A Turn off the power.
B Using the tip of a ball-point pen, press the test button of the earth leakage
circuit breaker.
7
ANQ087S
C Confirm that the earth leakage circuit breaker switch moves to the off position.
ANQ088S
109
Remarks
D Turn the switch to the on position.
ANQ089S
E Turn on the main power switch of the machine.
Note
❒ If the power does not come on, check if the earth leakage circuit breaker is
in the off position. If so, do not turn it to the on position. Contact your sales
or service representative immediately.
7
110
INDEX
A
Access to the Machine, 106
Adding
Paper, 59
Staples, 85
Toner, 82
Adding Staples
Booklet Finisher, 86
Finisher, 85
Alert Messages, 36
Auto Document Feeder (ADF), 108
B
E
Earth Leakage Circuit Breaker, 109
Edit, 27
Enquiry, 5
Environment, 103
Environments to avoid, 104
Error Log, 37
Exposure Glass, 107
F
Finisher, 81, 85, 100, 102
H
Booklet Finisher, 86, 101
C
Cannot Browse the Network
to Send a Scan File, 46
Cannot Exit from Connect Copy, 24
Cannot Make Clear Copies, 25
Cannot Make Copies As Wanted, 27
Cannot Print, 38
Cannot Send Scanned Files, 46
Changing the Paper Size, 70
LCT (Tray 4 and 5), 72
Tray 2 and 3, 70
Wide LCT, 76
Changing to a Size that is
Not Automatically Detected, 78
Checking Machine Status and Settings, 5
Checking the Error Log, 37
Cleaning
Auto Document Feeder, 108
Exposure Glass, 107
Clearing Misfeeds, 87
Combine, 27
Connect Copy, 22, 23, 24, 30
Connect Copy is Cancelled, 23
Copy Function, 17
D
Data Storage, 5
Display During Connect Copy, 22
Document Server, 9
Duplex, 27
How to Read This Manual, 1
I
If USB Connection Fails, 34
Indicators, 3
Inserting Toner, 84
Interposer, 67
J
Job is Not Performed, 14
L
Large Capacity Tray (LCT), 63, 72
Letterhead, 68
Loading Paper, 59
Interposer, 67
LCT, 63
Multi Bypass Tray (Tray 7), 65
Tray 2 and 3, 62
Wide LCT, 64
Locating Jammed Paper, 88
M
Machine Address Info, 5
Machine environment, 103
Maintaining Your Machine, 107
Maintenance Info, 5
Manuals for This Machine, i
Memory is Full, 30
Moving, 104
Multi-accessing, 14
Multi Bypass Tray (Tray 7), 65
111
N
Names of Major Options, 2
O
Operations are Not Possible
When Messages Appear, 47
Optimum environmental conditions, 103
Other Printing Problems, 40
P
Panel Tone, 4
Pausing Copy When Using Finisher, 81
Power connection, 105
Printer Function, 31
Printing surface, 68
Problems Operating the Machine, 9
Punch Waste, 102
R
W
When a Message Appears
Copy Function, 17
Printer Function, 35
Scanner Function, 48
Scanner Function (Client Computer), 54
When a Message Appears during
Installation of the Printer Driver, 31
When an Indicator to
the Left of a Function Key is Lit, 8
When the Machine
Does Not Operate As wanted, 3
When Z-folded paper is
not properly aligned, 99
Wide Large Capacity Tray (Wide LCT), 64, 76
Windows 2000, 32
Windows 95/98/Me, 31
Windows NT 4.0, 33
Windows Server 2003, 32
Windows XP, 32
Removing Jammed Paper, 87, 90
Removing Jammed Staples, 100
Booklet Finisher, 101
Finisher, 100
Removing Punch and Staple Waste, 102
S
Scanner Function, 45
Scanning is Not Done as Expected, 45
Stamp, 27
Staple Waste, 102
Status Messages, 35
Stored Files Cannot Be Accessed, 46
Stored Files Cannot be Edited, 47
T
Toner, 82
Tray 1 (Tandem Tray), 59
Troubleshooting
Copy Function, 17
Printer Function, 31
Scanner Function, 45
TWAIN, 46, 54
TWAIN Driver Cannot be Started, 46
U
Used Toner, 84
112
EN
USA
B235-7412
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
a means POWER ON.
c means STAND BY.
Copyright © 2006
MULTIFUNCTIONAL DIGITAL SYSTEMS
Operator's Manual Troubleshooting
2-17-2, HIGASHIGOTANDA, SHINAGAWA-KU, TOKYO, 141-8664, JAPAN
R060520B8300-TTEC
OME06008100
Ver00 2006-09
EN
2006 TOSHIBA TEC CORPORATION All rights reserved
B235-7412
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising