=M1264F SERIES GRAPHIC MODULE VER1.1 REVISION RECORD VER1.1

=M1264F SERIES GRAPHIC MODULE  VER1.1  REVISION RECORD VER1.1
=M1264F SERIES GRAPHIC MODULE VER1.1
REVISION RECORD
REVISION
VER1.1
REVISION DATE
15/6-2006
PAGE
CONTENTS
MODIFY THE COVER,ADD CONTENT AND
REVISION RECORD.
1
=M1264F SERIES GRAPHIC MODULE VER1.1
※ CONTENTS
1.0 MECHANICAL DIAGRAM
2.0 MECHANICAL SPECS
3.0 ABSOLUTE MAXIMUM RATINGS
4.0 ELECTRICAL CHARACTERISTICS
5.0 OPTICAL CHARACTERISTICS
6.0 BLOCK DIAGRAM
7.0 PIN ASSIGNMENT
8.0 POWER SUPPLY
9.0 TIMING CHARACTERISTICS
10.0 RELIABILITY TEST
11.0 RELATION BETWEEN DISPLAY PATTERN AND DRIVERS
12.0 DISPLAY CONTROL INSTRUCTION
2
2.0
=M1264F SERIES GRAPHIC MODULE VER1.1
MECHANICAL SPECS
1. Overall Module Size
93.0mm(W) x 70.0mm(H) x max 14.0mm(D) for LED backlight
version
93.0mm(W) x 70.0mm(H) x max 9.5mm(D) for reflective
version
2. Dot Size
0.48mm(W) x 0.48mm(H)
3. Dot Pitch
0.52mm(W) x 0.52mm(H)
4. Duty
1/64
5. Controller IC
KS0108B
6. LC Fluid Options
STN, FSTN
7. Polarizer Options
Reflective, Transflective, Transmissive
8. Backlight Options
LED
9. Temperature Range Options
Standard (0ºC ~ 50ºC), Wide (-20ºC ~ 70ºC)
3.0 ABSOLUTE MAXIMUM RATINGS
Item
Symbol
Min
Typ
Max
Unit
Operating temperature (Standard)
Top
0
-
50
ºC
Storage temperature (Standard)
Tst
-10
-
60
ºC
Operating temperature (Wide temperature)
Top
-20
-
70
ºC
Storage temperature (Wide temperature)
Tst
-30
-
80
ºC
Input voltage
Vin
Vss
Vdd
V
Supply voltage for logic
Vdd- Vss
-0.3
-
6.0
V
Supply voltage for LCD drive
Vdd- Vo
-
-
15.0
V
4.0 ELECTRICAL CHARACTERISTICS
Item
Symbol
Condition
Min
Typ
Max
Unit
Input voltage (high)
Vih
H level
0.8Vdd
-
Vdd
V
Input voltage (low)
Vil
L level
0
-
0.2Vdd
V
0ºC
-
12.2
12.8
25ºC
-
11.5
-
50ºC
10.2
10.6
-
-20ºC
-
13.0
14.0
0ºC
-
12.2
-
50ºC
10.2
10.6
-
70ºC
9.5
10.0
-
Idd
Vdd=5.0V
-
-
15.0
mA
LED Power Supply Voltage
Vfled
R=6.8Ω
-
4.6
5.0
V
LED Power Supply Current
Ifled
R=6.8Ω
-
470
560
mA
Recommended LC Driving
Voltage (Standard Temp)
Recommended LC Driving
Voltage (Wide Temp)
Power Supply Current
Vdd - Vo
Vdd -Vo
V
V
4
=M1264F SERIES GRAPHIC MODULE VER1.1
5.0 OPTICAL CHARACTERISTICS
Item
Mode
R
S
Cr (Contrast Ratio)
θ (Viewing Angle)
φ (Viewing Angle)
25ºC
25ºC
25ºC
MIN.
TYP.
MIN
TYP.
MIN
TYP.
A
2.8
3.05
80°
85°
-
35°
B
7.10
7.70
80°
85°
-
35°
C
-
-
-
-
-
-
A
2.49
2.99
80°
85°
-
35°
B
7.05
7.55
80°
85°
-
35°
C
-
-
-
-
-
-
Note:
R: Reflective
S: Transflective
A: STN Gray
B: STN Yellow
C: FSTN
At: φ =0°, θ =0°
Item
Symbol
Condition
Min
Typ
Max
Unit
Response time (rise)
Tr
25 ºC
-
140
280
ms
Response time (fall)
Tf
25ºC
-
80
160
ms
6.0
BLOCK DIAGRAM
VLCD
KS0107
BIAS
Back Light
COM0
COM63
S0-S63
KS0108
U1
S0-S63
KS0108
U2
5
7.0
=M1264F SERIES GRAPHIC MODULE VER1.1
PIN ASSIGNMENT
Pin No.
Symbol
Function
Level
1
Vss
Ground
-
2
Vdd
+5V
-
3
Vo
LCD contrast adjust
-
4
D/I
5
R/W
H: Data input
H/L
L: Instruction code input
H: Data read
H/L
L: Data write
8.0
6
E
Enable signal
H,H → L
7
DB0
Data bit 0
H/L
8
DB1
Data bit 1
H/L
9
DB2
Data bit 2
H/L
10
DB3
Data bit 3
H/L
11
DB4
Data bit 4
H/L
12
DB5
Data bit 5
H/L
13
DB6
Data bit 6
H/L
14
DB7
Data bit 7
H/L
15
CS1
Chip selection for IC1
H
16
CS2
Chip selection for IC2
H
17
RST
Reset
L
18
VLCD
Power Supply for LCD Driving
-
19
20
VLED+-
Power Supply for BL-
-
VLED-+
Power Supply for BL+
-
POWER SUPPLY
R=10K~20KΩ
6
=M1264F SERIES GRAPHIC MODULE VER1.1
9.0 TIMING CHARACTERISTICS
Symbol
Test Condition
Min.
Typ.
Max.
Unit
Enable cycle time
Item
tCYC
Fig. a, Fig. b
1000
-
-
ns
E high level width
tWH
Fig. a, Fig. b
450
-
-
ns
E low level width
tWL
Fig. a, Fig. b
450
-
-
ns
Enable rise/fall time
Tr , tf
Fig. a, Fig. b
-
-
25
ns
Address set up time
tAS
Fig. a, Fig. b
140
-
-
ns
Address hold time
tAH
Fig. a, Fig. b
10
-
-
ns
Data delay time
tDDR
Fig. b
-
-
320
ns
Data set up time
tDSW
Fig. a
200
-
-
ns
Data hold time (Write)
tDHW
Fig. a
10
-
-
ns
Data hold time (Read)
tDHR
Fig. b
20
-
-
ns
D/ I
2.2V
2.2V
0.8V
0.8V
CS1~CS2
t AS
2.2V
R/W
2.2V
0.8V
0.8V
t AH
tr
E
2.2V
tf
2.2V
t WL
0.8V
2.2V
t WH
0.8V
0.8V
t DSW
2.2V
DB0~DB7
0.8V
t DHW
2.2V
Valid Data
0.8V
t cyc
Fig. a Interface timing (data write)
D /I
CS1~CS2
2 .2 V
2 .2 V
0 .8 V
0 .8 V
t AS
2 .2 V
R /W
2 .2 V
tAH
tr
E
2 .2 V
2 .2 V
tWL
0 .8 V
tf
2 .2 V
tWH
0 .8 V
2 .2 V
D B0~D B7
0 .8 V
tDHR
t DDR
0 .8 V
V a lid D a ta
2 .2 V
0 .8 V
t cyc
Fig. b Interface timing (data read)
7
=M1264F SERIES GRAPHIC MODULE VER1.1
10.0 RELIABILITY TEST
Evaluations and Assessment*
Storage Condition
Operation at high
temperature and
humidity
High temperature
storage
Low temperature
storage
Content
Current
Consumption
Oozing
Contrast
Other
Appearances
40ºC,90%
RH,240hrs
Twice initial
value or less
none
More than 80% of
initial value
No abnormality
60ºC,
240hrs
-20ºC,
240hrs
Twice initial
value or less
Twice initial
value or less
none
More than 80% of
initial value
No abnormality
More than 80% of
initial value
No abnormality
*Evaluations and assessment to be made two hours after returning to room temperature (25ºC±5ºC).
*The LCDs subjected to the test must not have dew condensation.
11.0 RELATION BETWEEN DISPLAY PATTERN AND DRIVERS
8
=M1264F SERIES GRAPHIC MODULE VER1.1
12.0 DISPLAY CONTROL INSTRUCTION
The display control instructions control the internal state of the KS0108B. Instructions are received
from MPU to KS0108B for the display control.
INSTRUCTION
Display
ON/OFF
D/I
0
R/W
0
DB7
0
DB6
0
DB5 DB4
1
1
DB3
1
DB2
1
DB1 DB0
1
1/0
DESCRIPTION
Controls the display on or off.
Display RAM data and internal
status is not affected.
0: OFF. 1:ON
Set Address
(Y address)
Set Page
(X address)
0
0
0
1
0
0
1
0
0
0
1
1
1
Y address (0~63)
Sets the Y address at the Y
address counter.
1
Sets the X address at the X
address register.
1
Page (0~7)
Display Start
Line
Indicates the display data RAM
displayed at the top of the screen.
Display start line (0~63)
(Z address)
Read status:
BUSY
0
RESET
1
ON/OFF
0
BUSY
Status Read
0:Ready
1:In operation
0
0
0
0
ON/OFF
0:Display ON
1:Display OFF
RESET
0:Normal
1:Reset
Write Display
Data
1
0
Write Data
Writes data DB0~DB7 into display
data RAM. After writing
instruction, Y address is
increased by 1 automatically.
Read Display
Data
1
1
Read Data
Reads data DB0~DB7 from
display data RAM to the data bus.
9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising