204523A

204523A
MODEL №: 204523A
AMERICAN SPECIALTIES, INC.
441 Saw Mill River Road, NY 10701
(914) 476.9000 • (914) 476.0688
www.americanspecialties.com
ISSUED:
10/09
REVISED:
05/10
ROVAL™ RECESSED AUTOMATIC ROLL PAPER TOWEL DISPENSER
17-3 8" [441]
10" [254]
11-1116" [297]
9
32"
[7] TYP
CONCEALED
PIANO
HINGE
2-15 16"
[75]
10" [254]
13"
[330]
15-3 4" [400]
2-7 8"
[73]
7
32" DIA [Ø5.6]
MOUNTING
HOLES TYP 4
13-3 4"
[349]
NOTE: ALL DIM'S
ARE INCH [MM]
8-116" [205]
712"
[191]
INTERLOCK
SWITCH
ROUGH WALL OPENING
48" AFF [1219]
ADA MAX
40" AFF [1016]
CBC MAX
27-3 4"
[705]
NO TOUCH - PLACE HAND BELOW
TUMBLER
LOCK
FRONT VIEW
26"
[660]
7
DIA
[Ø5.6]
MOUNTING
HOLES
TYP
LED
INDICATOR
32"
MINIMUM DEPTH
10"
[254]
BARRIER FREE MOUNTING HEIGHT MAX AFF
ADA REACH 61-1 4" [1556] •CBC ALL REACH 53-1 4" [1353]
32" [7]
RECOMMENDED MOUNTING HEIGHT AFF
62-1 4" TO 69-14" [1581 TO 1759]
9
SIDE VIEW
SPECIFICATION
Roval™ Collection Recess Mounted Automatic Roll Paper Towel Dispenser shall hold and dispense one 8" wide x 8" diameter (203 x Ø203)
standard towel roll up to 800 ft. (244m) long and one 8" wide (203) stub roll up to 4" diameter (Ø102). Cabinet full door shall be drawn
seamless and shall have bowed front face and gently radiused edges to provide added strength and complimentary appearance for modern
washroom aesthetics. Automatic Touchless Roll Towel Dispenser shall be powered by four (4) D-size batteries (not supplied) and shall operate
automatically to activate towel dispensing when hands are placed in sensor zone. At each activation unit shall feed out a length of towel selected by owner by setting length, delay and paper saver switches. Unit shall have an internal towel cut-off bar. Cabinet and frame shall be 22
gauge type 304 stainless steel alloy 18-8. Towel dispenser door shall be 18 gauge same grade and shall have a full return and formed sill at
bottom edge for user safety. All exposed surfaces shall have satin finish protected by PVC film easily removed after installation. Door shall be
attached to cabinet at side with a full-length 1/8" dia. (Ø3.1) stainless steel multi-staked piano hinge and shall be held closed with a flush rimless tumbler lock keyed alike to other ASI washroom equipment. Internally concealed doorstop shall prevent over-swing when opened rapidly. Face trim shall be 1" (25) wide formed from one piece with no miters, welding or open seams and have 1/8" (3) radiused return to wall.
Structural assembly of all components shall be of welded construction. Cabinet shall have no exposed fastening devices or spot-welded seams.
Roval™ Collection Recess Mounted Automatic Roll Paper Towel Dispenser shall be Model № 204523A of American Specialties, Inc.,
441 Saw Mill River Road, Yonkers, New York 10701-4913
INSTALLATION
Provide adequate in-wall reinforcement (by others) in drywall construction to hold mounted unit in-service after wall is finished. Provide appropriate anchors (by others) to suit wall and field conditions for installation into walls other than new drywall. Mount unit in wall recess using
№ 10 self-tapping screws (by others) through concealed mounting holes provided. Note that top of RWO is 7/8" (22) below top of unit. For
compliance with ICC/ANSI A-117.1-2003 and ADA Accessibility Guidelines install unit so that top edge of towel dispenser opening is
48" (1219) maximum above finished floor (MAX AFF) only if clear floor reach access is provided. Be advised that local codes may require
mounting so that top of towel dispenser opening is 40" (1016) MAX AFF (e.g. California UBC/Title 24). For general utility install unit with
top of towel dispenser opening between 49" and 56" (1245 to 1422) AFF. Sensor ground wire must be connected inside cabinet.
Rough Wall Opening (RWO) required is 15-3/4" W x 26" H x 10" D minimum (400 x 660 x 254)
OPERATION
Towels are dispensed one length at a time automatically when hands are placed in sensor zone until supply is depleted. Owner predetermines
length of towel dispensed by making selections on three (3) three-position switches for length, delay, and economy. Unit may be reloaded
with a full roll to automatically start when finished with an existing partial roll and will continue to feed properly when reloaded with a
full roll and partial roll is transferred to stub roll position. Refill dispenser by unlocking door and replacing towel roll for an empty or
partially empty unit. Dispenser supply is replenished and batteries are replaced manually on cycles determined by maintenance needs.
LED indicates sensing and battery condition. Locking door prevents unauthorized access and roll removal.
THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising