Blade SR UH-1 Huey Gunship Manual

Blade SR UH-1 Huey Gunship Manual
RTF
SR UH-1 HUEY GUNSHIP
Instruction Manual
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature,
visit horizonhobby.com and click on the support tab for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, serious injury or death
OR create a high probability of superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product
correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this
Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without
direct adult supervision. Do not attempt disassembly, use with incompatible components or augment product in any way without the approval of Horizon Hobby,
Inc. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual,
prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Additional Safety Precautions and Warnings
• Always keep all chemicals, small parts and anything electrical out of the
reach of children.
• Always avoid water exposure to all equipment not specifically designed and
protected for this purpose. Moisture causes damage to electronics.
• Never place any portion of the model in your mouth as it could cause serious
injury or even death.
• Never operate your model with low transmitter batteries.
Age Recommendation: Not for children under 14 years. This is not a toy.
• Always keep a safe distance in all directions around your model to avoid
collisions or injury. This model is controlled by a radio signal subject to
interference from many sources outside your control. Interference can cause
momentary loss of control.
• Always operate your model in open spaces away from full-size vehicles, traffic and people.
• Always carefully follow the directions and warnings for this and any optional
support equipment (chargers, rechargeable battery packs, etc.).
Battery Warnings
• Never leave charging batteries unattended.
• Always charge batteries away from flammable materials.
• Never charge batteries outside safe termpeature range.
• Never charge batteries outside recommended levels.
• Never charge damaged batteries.
• Store batteries safely.
• By handling, charging or using the included Li-Po battery, you assume all
risks associated with lithium batteries.
• If at any time the battery begins to balloon or swell, discontinue use immediately. If charging or discharging, discontinue and disconnect. Continuing
to use, charge or discharge a battery that is ballooning or swelling can result
in fire.
• Always store the battery at room temperature in a dry area for best results.
• Always transport or temporarily store the battery in a temperature range of
40–120º F. Do not store battery or model in a car or direct sunlight. If stored
in a hot car, the battery can be damaged or even catch fire.
• NEVER USE A Ni-Cd OR Ni-MH CHARGER. Failure to charge the battery with
a compatible charger may cause fire resulting in personal injury and/or
property damage.
• Never discharge Li-Po cells to below 3V under load.
• Never cover warning labels with hook and loop strips.
The Battery Charger included with your aircraft is designed to safely charge
the Li-Po battery.
CAUTION: All instructions and warnings must be followed exactly.
Mishandling of Li-Po batteries can result in a fire, personal injury, and/or
property damage.
France RF Setting:
The included transmitter has a France RF setting that complies with French regulations. When in France, always use the France power setting when operating the
transmitter outdoors. See page 7 for more information.
EN
2
Introduction
The UH-1 Huey was the first turbine powered helicopter to enter production for the U.S. Military and is most famously known for it’s service in the Vietnam War.
This scale licensed Huey is based on that famous helicopter. Combined with SR flight characteristics, the Blade® Huey is a great combination of scale and
performance for Ready to Fly helis.
Before you fly the helicopter, you must read this manual. The Blade SR UH-1 Huey is a sophisticated Radio Controlled flying machine that has some features and
pre-flight checks you will need to be familiar with before you fly.
Table of Contents
Blade SR UH-1 Huey Specifications
Charging the Flight Battery............................................................................ 4
Low Voltage Cutoff (LVC)................................................................................ 4
Throttle Hold.................................................................................................. 4
Stunt Mode.................................................................................................... 5
Transmitter and Receiver Binding................................................................... 5
Installing the Flight Battery............................................................................ 5
Control Test................................................................................................... 6
Elevator......................................................................................................... 6
Collective Pitch.............................................................................................. 6
Aileron........................................................................................................... 6
Flying the Blade SR UH-1 Huey...................................................................... 7
Gyro Gain Adjustment.................................................................................... 7
Post-Flight Inspections and Maintenance....................................................... 7
RF Mode........................................................................................................ 7
Limited Warranty........................................................................................... 8
Warranty and Service Contact Information..................................................... 8
Customer Service Information........................................................................ 8
FCC Information............................................................................................. 9
Compliance Information for the European Union............................................. 9
Exploded View............................................................................................. 10
Parts List .................................................................................................... 13
Length
25.8 in (655mm)
Height
9.3 in (235mm)
Main Rotor Diameter
21.8 in (550mm)
Tail Rotor Diameter
3.2 in (80mm)
Gross Weight
12 oz (340 g)
Components
Main Motor
Brushless outrunner, 3900Kv (installed)
Tail Motor
Direct drive N60 (installed)
Onboard Electronics
2-in-1 Mixer/ESC (installed)
Battery
3S 11.1V 1000mAh Li-Po
Charger
DC Li-Po Balancing Charger
Power Supply AC to 12V DC, 1.5A
Transmitter
HP6DSM SR 2.4GHz DSM® 6-Channel
with AA Batteries
Receiver
Spektrum™ 6100e Microlite 6-Channel
DSM® Receiver (installed)
Swash Servos
DS75 Digital Sub-Micro (installed)
Gyro
G110 Micro Heading Lock (installed)
To register your product online, visit www.bladehelis.com
3
EN
Charging the Flight Battery
DC Li-Po Balancing Charger Features
The Blade SR UH-1 Huey comes with a DC balancing charger and 3S Li-Po
battery. You must charge the included Li-Po battery pack with a Li-Po specific
charger only (such as the included charger). Never leave the battery and charger unattended during the charge process. Failure to follow the instructions
properly could result in a fire. When charging, make sure the battery is on a
heat-resistant surface. Fully charge the flight battery before binding the aircraft
or performing control tests.
• Charges 3-cell lithium polymer battery packs
• 800mA charge rate
• LED charge status indicator
• 12V alligator clip input cord
Specifications
• Input power: 12V DC, 1.5-amp
• Charges 3-cell Li-Po packs with minimum capacity of 1000mAh
3S 11.1V 1000mAh Li-Po Battery Pack
The Blade SR UH-1 Huey 3S Li-Po battery pack features a balancing lead that
allows you to safely charge your battery pack when used with the included
Li-Po balancing charger.
WARNING: The balance connector must be inserted into the correct port
of your charger prior to charging.
The Battery Charging Process
1.
Charge only batteries that are cool to the touch and are not damaged. Look at the battery to make sure it is not damaged e.g., swollen,
bent, broken or punctured.
2.
Connect the charger to a 12V power source or the included AC power supply, noting proper polarity. 3.
The red LED flashes.
4.
Connect the battery balance lead to the charger. The balance connector is keyed to prevent reverse polarity.
5.
The red and green LEDs glow solid when the battery is charging.
6.
Charging is complete when only the red LED glows solid.
7.
Always unplug the battery from the charger immediately upon completion of charging.
CAUTION: Overcharging a battery can cause a fire.
NOTICE: Attempting to charge an over-discharged battery will cause the charger to repeatedly flash red and green, indicating an error has occured.
CAUTION: Only use a charger specifically designed to charge a Li-Po battery. Failure to do so could result in fire causing injury or property damage.
CAUTION: Never exceed the manufacturer’s recommended charge rate.
Low Voltage Cutoff (LVC)
Disconnect and remove the Li-Po battery from the aircraft after use to prevent
trickle discharge. Fully charge and store the Li-Po battery in a safe location.
During storage, ensure the battery charge does not fall below 3V per cell.
The ESC will continuously lower power to the motor until complete shutdown occurs once the battery reaches 9V under load. This helps prevent overdischarge of the Li-Po battery. Land immediately when the helicopter requires
increased throttle to maintain hover. Continuing to fly after LVC can damage the
battery, cause a crash or both. Crash damage and batteries damaged due to
over-discharge are not covered under warranty.
Throttle Hold
Throttle hold only turns off the motor on an electric helicopter. You must
maintain pitch and direction control.
The blades will spin if the throttle hold is OFF (0). For safety, turn the throttle
hold ON (1) any time you need to touch the helicopter or check the direction
controls.
Additionally, throttle hold is used to turn off the motor if the helicopter is out
of control, in danger of crashing, or both. Throttle hold will also allow you to
perform an auto-rotation landing once the helicopter has sufficient altitude.
EN
4
Stunt Mode
Change between stunt and idle up modes in a hover with the throttle near the
middle stick position. Stunt Mode allows you to fly aerobatics.
When the helicopter is in stunt mode:
The helicopter may go up or down when you change between modes due to
the difference in the throttle and pitch curves.
- The rotor head speed is constant.
- The main rotor will increase negative pitch as the throttle/collective stick is
moved from the middle stick position to the low stick position. Negative pitch
allows the helicopter to fly upside down and perform mild aerobatics. Turn the SM TCM ADJ knob to the full clockwise (+) position for maximum
throttle in stunt mode.
Transmitter and Receiver Binding
Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. You need to ‘bind’ your
chosen Spektrum™ DSM technology equipped aircraft transmitter to the receiver for proper operation.
If you choose to use a different Spektrum DSM radio than the one included, please follow these binding instructions for proper operation.
Binding Procedure
1.
Read the transmitter instructions for binding to a receiver (location of transmitter’s Bind control).
2.
Make sure the transmitter is powered off.
3.
Install a bind plug in the helicopter’s extension labeled ‘bind’.
4.
Connect the flight battery to the ESC. The receiver LED will begin to flash rapidly.
5.
Move the transmitter controls to neutral (flight controls: rudder, elevators and ailerons) or to low positions (throttle).
6.
Power on the transmitter while holding the transmitter bind button or switch. Refer to your transmitter’s manual for instructions.
7.
When the receiver binds to the transmitter, the receiver light will turn solid.
8.
Disconnect the flight battery from the ESC. Remove the bind plug from the extension.
9.
Safely store the bind plug (some owners attach the bind plug to their transmitter using two-part loops and clips).
10. The receiver will keep the bind to the transmitter until another binding is done.
11. Always perform the control test shown in this manual before flying the helicopter.
If you encounter problems, refer to the transmitter troubleshooting guide for other instructions.
If needed, contact the appropriate Horizon Product Support office.
Installing the Flight Battery
Mode 2 Shown
4. Install the flight battery on the helicopter frame. Secure the battery with a
1. Power on the transmitter.
hook and loop strap. Connect the battery cable to the ESC.
2. Lower throttle and center the throttle trim.
5. Wait 5 seconds while the gyro initializes.
WARNING: After connecting the battery, move Throttle Hold (TH HOLD) switch to position (1).
6. The aircraft will emit 2 tones and a solid red LED on the gyro once it is
ready.
3. Attach loop material to the battery and hook material to the helicopter
frame.
CAUTION: Always disconnect the Li-Po battery from the aircraft receiver when not flying to avoid over-discharging the battery.
Batteries discharged below 9V may become damaged, resulting in loss of performance and potential fire when batteries are charged.
Do not move the helicopter after connecting the flight battery to let the helicopter gyro calibrate. Do not allow the battery to touch the motor.
5
EN
Control Test
WARNING: Stay at least 30 feet (10 meters) away from the helicopter
when the motor is running. Do not attempt to fly the helicopter at this
time.
7. Ensure the throttle is lowered completely. Move the TH HOLD switch to the
(0) position. Slowly increase the throttle until the blades begin to spin. The
main blades spin clockwise when viewing the helicopter from the top. The
tail rotor blades spin counterclockwise when viewing the helicopter from
the right-hand side.
Place the helicopter on a clean and flat ground surface (concrete or asphalt)
free of obstructions. Always stay clear of the moving rotor blades.
CAUTION: Keep pets and other animals away from the helicopter.
Animals may injure themselves if they attack or run toward the
helicopter.
1. Move the throttle stick to idle/low stick position and move all transmitter
switches to the (0) position.
2. Turn the transmitter on.
CAUTION: The transmitter battery alarm beeps when the transmitter
batteries are 4.3V or less. Replace the transmitter batteries when the
alarm beeps.
3. Connect the red JST battery connector to the helicopter’s 2-in-1 unit. Do
not allow the helicopter to move until the red LED on the gyro is solid.
4. The motor beeps twice when the helicopter’s 2-in-1 unit arms properly. Move the Throttle Hold (TH HOLD) switch to the (1) position.
WARNING: The motor, main rotor and tail rotor will spin when the throttle
is increased if the TH HOLD switch is not moved to the (1) position.
5. Check the swashplate directions to ensure they are moving in the correct
direction. Please refer to the diagrams below for reference.
6. Place the helicopter in an open area outdoors.
NOTICE: If the main rotor blades are spinning backward, reduce the throttle to
idle. Move the throttle hold switch to the (1) position. Disconnect the battery
from the helicopter and reverse any two motor wire connections to the 2-in-1
unit.
Trainer TCM knob
CH 5 knob
(not used)
TH Hold
F Mode
Dual
Rate
MODE 2
Elevator
Side View
MODE 1
Side View
Collective Pitch
Rear View
Rear View
Rear View
Rear View
Aileron
EN
6
Flying the Blade SR UH-1 Huey
• Always keep moving parts clean.
• Always keep parts dry.
• Always let parts cool after use before touching.
• Always remove batteries after use.
• Never operate aircraft with damaged wiring
• Never touch moving parts
• Always keep the aircraft in sight and under control.
• Always ensure spectators, especially children, are at least 40 feet away
when the motor is running.
• Always turn on throttle hold at rotor strike.
• Always use fullly charged batteries.
• Always keep transmitter powered on while aircraft is powered.
• Always remove batteries before disassembly
Consult local laws and ordinances before choosing a location
to fly your aircraft.
hile attempting to establish a low-level hover, you can also check to see
W
if any trim adjustments are required to help keep the SR UH-1 Huey from
constantly drifting in various directions. If you find the aircraft drifts without any
directional control input, land the model before making any adjustments to the
trim settings.
Select a large, open area away from people and objects. Your first flights
should be outdoors in low-wind conditions. Do not attempt to fly the Blade SR
UH-1 Huey helicopter indoors. Always stay at least 30 feet (10 meters) away
from the helicopter when it is flying.
- If the helicopter drifts forward or backward, adjust the elevator trim.
- If the helicopter drifts to the left or right, adjust the aileron trim.
The Blade UH-1 Huey is not intended to be flown indoors where it might be
possible to fly a Blade mSR or Blade CX2. Experienced pilots may find it possible to fly the helicopter in a large gymnasium.
CAUTION: Familiarize yourself with the Blade SR UH-1 Huey primary controls before attempting your first flight. The Huey is more responsive than
other Blade helicopters, such as the Blade CX2. We recommend getting
help from an experienced pilot and installing training gear, if you are new
to collective pitch helicopters.
CAUTION: Always fly the helicopter with your back to the sun and wind
to prevent loss of flight control.
Continue making trim adjustments until the helicopter hovers at a low altitude
with very little drifting and directional control input. If the Blade SR UH-1 Huey
is your first helicopter model, seek help from an experienced pilot to trim the
model for you before making your first flight.
Gyro Gain Adjustment
• If the tail wags or oscillates, lower the gain on the gyro. Turn the pot on the gyro counterclockwise. You can access it through
the hole in the side of the fuselage.
• If the tail is drifting while hovering, increase the gain on the gyro.
Turn the pot on the gyro clockwise. You can access it through the hole
in the side of the fuselage.
Stock Dip Switch Settings on Gyro
Servo Mode
STD
Reverse
NOR
Post-Flight Inspections and Maintenance
Ball Links
Make sure the plastic ball link holds the control ball, but is not tight or binding on the ball. When a link is too loose on the ball, it can separate from the ball
during flight and cause a crash. Replace worn ball links before they fail.
Cleaning
Make sure the battery is not connected before cleaning. Remove dust and debris with a soft brush or a dry, lint-free cloth.
Bearings
Replace the bearings when they become sticky in places when turning.
Wiring
Make sure the wiring does not block moving parts. Replace any damaged wiring and loose connectors.
Fasteners
Make sure there are no loose screws, fasteners or connectors. Do not over tighten metal screws in plastic parts. Tighten screws so the parts are mated
together, then turn the screw only 1/8th of a turn more. Make sure the main rotor blade screws are properly tightened. Do not allow main rotor blades to
move freely in the blade grips.
Rotors
Make sure there is no damage to the rotor blades or other parts that move at high speed. Damage to these parts include: cracks, burrs, chips or scratches.
Replace damaged parts before flying.
RF Mode
Standard mode
The included transmitter has a France RF Mode that complies with French
regulations. The transmitter must be in France mode when used outdoors in
France. At all other times, the transmitter should be in Standard mode.
Power on the transmitter. Move the D Rate switch between Hi and Lo until the
screen displays “nF”.
France mode
Power on the transmitter, flip the D/R switch until the screen displays “F”.
7
EN
Limited Warranty
What this Warranty Covers
Horizon Hobby, Inc. (“Horizon”) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date
of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due
to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper
use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center,
or (v) Products not purchased from an authorized Horizon dealer.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY
OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY
MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon
will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be
defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof
of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY,
REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As
Horizon has no control over use, setup, final assembly, modification or misuse, no liability
shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup
or assembly, the user accepts all resulting liability. If you as the purchaser or user are not
prepared to accept the liability associated with the use of the Product, purchaser is advised
to return the Product immediately in new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law principals). This
warranty gives you specific legal rights, and you may also have other rights which vary
from state to state. Horizon reserves the right to change or modify this warranty at any
time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact
your local distributor or Horizon directly. This will enable Horizon to better answer your
questions and service you in the event that you may need any assistance. For questions
or assistance, please direct your email to productsupport@horizonhobby.com, or call
877.504.0233 toll free to speak to a Product Support representative. You may also find
information on our website at www.horizonhobby.com.
Inspection or Services
If this Product needs to be inspected or serviced, please use the Horizon Online Service
Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton.
Please note that original boxes may be included, but are not designed to withstand the
rigors of shipping without additional protection. Ship via a carrier that provides tracking
and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise
until it arrives and is accepted at our facility. An Online Service Request is available at
http://www.horizonhobby.com under the Support tab. If you do not have internet access,
please contact Horizon Product Support to obtain a RMA number along with instructions
for submitting your product for service. When calling Horizon, you will be asked to provide
your complete name, street address, email address and phone number where you can be
reached during business hours. When sending product into Horizon, please include your
RMA number, a list of the included items, and a brief summary of the problem. A copy
of your original sales receipt must be included for warranty consideration. Be sure your
name, address, and RMA number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt verifying
the proof-of-purchase date. Provided warranty conditions have been met, your Product
will be serviced or replaced free of charge. Service or replacement decisions are at the
sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty service will be completed and payment will be required without notification or estimate of the expense unless the
expense exceeds 50% of the retail purchase cost. By submitting the item for service
you are agreeing to payment of the service without notification. Service estimates are
available upon request. You must include this request with your item submitted for service.
Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition
you will be billed for return freight. Horizon accepts money orders and cashiers checks, as
well as Visa, MasterCard, American Express, and Discover cards. By submitting any item
to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our
website http://www.horizonhobby.com/Service/Request/.
Warranty and Service Contact Information
Country of Purchase
Horizon Hobby
Address
Phone Number / Email Address
Horizon Service Center
(Electronics and engines)
4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
877-504-0233
Online Repair Request visit: www.horizonhobby.com/service
Horizon Product Support
(All other products)
4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
877-504-0233
productsupport@horizonhobby.com
United Kingdom
Horizon Hobby Limited
Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex, CM18 7NS, United Kingdom
+44 (0) 1279 641 097
sales@horizonhobby.co.uk
Germany
Horizon Technischer Service
Hamburger Str. 10
25335 Elmshorn, Germany
+49 4121 46199 66
service@horizonhobby.de
France
Horizon Hobby SAS
14 Rue Gustave Eiffel
Zone d’Activité du Réveil Matin
91230 Montgeron
+33 (0) 1 60 47 44 70
infofrance@horizonhobby.com
United States of
America
Customer Service Information
Country of Purchase
EN
Horizon Hobby
Address
Phone Number / Email Address
United States
Sales
4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
(800) 338-4639
sales@horizonhobby.com
United Kingdom
Horizon Hobby Limited
Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex, CM18 7NS, United Kingdom
+44 (0) 1279 641 097
sales@horizonhobby.co.uk
Germany
Horizon Hobby GmbH
Hamburger Str. 10
25335 Elmshorn, Germany
+49 4121 46199 60
service@horizonhobby.de
France
Horizon Hobby SAS
14 Rue Gustave Eiffel
Zone d’Activité du Réveil Matin
91230 Montgeron
+33 (0) 1 60 47 44 70
infofrance@horizonhobby.com
8
FCC Information
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
This product contains a radio transmitter with wireless technology which has been tested and found to be
compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
Antenna Separation Distance
When operating your E-flite transmitter, please be sure to maintain a separation distance of at least 5 cm between
your body (excluding fingers, hands, wrists, ankles and feet) and the antenna to meet RF exposure safety requirements as determined by FCC regulations.
These illustrations show the approximate 5 cm RF exposure area and typical hand placement when operating your
E-flite transmitter.
Compliance Information for the European Union
AT
BG
CZ
CY
DE
DK
ES
FI
FR
GR
LU
HU
IE
IT
LT
LV
MT
NL
PL
PT
RO
SE
SI
SK
UK
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH2011081201
Product(s):
Item Number(s):
Equipment class:
Blade SR UH-1 Huey Gunship RTF
BLH1700EU1, BLH1700EU2, BLH1700UK1, BLH1700UK2
2
The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European
R&TTE Directive 1999/5/EC and EMC Directive 2004/108/EC:
EN 300-328 V1.7.1
EN 301 489-1 V1.7.1: 2006
EN 301 489-17 V1.3.2: 2008
EN 60950-1:2006+A11
EN55022: 2006,
EN55024: 1998+A1: 2001+A2: 2003
(EN61000-4-2: 2001, EN61000-4-3: 2006, EN61000-4-8: 2001)
Signed for and on behalf of:
Horizon Hobby, Inc.
Champaign, IL USA
August 12, 2011
Steven A. Hall
Vice President
International Operations and Risk Management
Horizon Hobby, Inc.
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it
over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your
waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human
health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city
office, your household waste disposal service or where you purchased the product.
9
EN
EN
10
11
EN
EN
12
Parts List
#
Part #
Description
#
Part #
Description
1
BLH1740
SR UH-1 Huey Gunship Body Kit: SR Huey
23
EFLH1323
Direct-Drive Tail Rotor Blade/Prop Adapter: BCPP2, BSR/Huey
2
BLH1741
Landing Gear Set: SR Huey
24
EFLH1322
Direct-Drive N60 Tail Motor: BCPP2, BSR/Huey
3
BLH1742
Tail Motor Mount Assembly: SR Huey
26
EFLH1385
Main Blades, Huey: BCP, CP+, CPPro, CPPro2, BSR/Huey
4
BLH1743
Gun Pods: SR Huey
27
EFLH1387
5
EFLA308H
2-in-1 Helicopter Brushless ESC/Mixer: BSR/Huey
Tail Rotor Blade Black, Huey: BCP,CP+,CPPro,CPPro2, BSR/
Huey
6
EFLB0998
1000mAh 3S 11.1V 20C LiPo 20AWG JST
28
EFLH1409
Pinion Gear, 9T 0.5M: B400, BSR/Huey, B450
7
EFLC3105
3-Cell Li-Po Balancing Charger, 0.8A
29
EFLH1444
Hook and Loop Battery Strap: B400, BSR/Huey
8
EFLC4000
AC to 12VDC, 1.5-Amp Power Supply
30
EFLH1501
Main Frame: BSR/Huey
EFLC4000AU
AC to 12VDC, 1.5 Amp Power Supply AU Plug
31
EFLH1503
Tail Boom, Blue: BSR/Huey
EFLC4000EU
AC to 12VDC, 1.5 Amp Power Supply EU Plug
32
EFLH1508
Main Shaft (2): BSR/Huey
EFLC4000UK
AC to 12VDC, 1.5 Amp Power Supply UK Plug
9
EFLH1057
HP6DSM 6-Channel Transmitter, 2.4GHz DSM2: BSR/Huey
10
EFLH1115
Bearing 3x6x2.5mm (2):BCP/P/B400/BSR/Huey
11
EFLH1523
Spindle/Feathering Shaft (2): BCP/BCPP/BCPP2/BSR/Huey
12
EFLH1146
Rotor Head Set: BCP, BCPP, BSR/Huey
13
EFLH1148
Paddle Control Frame: BCP, BCPP, BSR/Huey
14
EFLH1149
Flybar (2): BCP, BCPP, BSR/Huey
15
EFLH1150
Paddle Set: BCP, BCPP, BSR/Huey
16
EFLH1151
Pitch Control Link Set: BCP, BCPP, BSR/Huey
17
EFLH1163
Paddle Control Frame Pushrod Set: BCP, BCPP, BSR/Huey
18
EFLH1165
Flybar Weight (2): BCP, BCPP, BSR/Huey
19
EFLH1171
Bell Mixer Main Blade Grip Set: BCP, BCPP, BSR/Huey
20
EFLH1172
Bell Mixer Arm & Pushrod Set: BCP, BCPP, BSR/Huey
21
EFLH1215
Bearing 4 x 8 x 3mm (2): BCX/2/3, BSR/Huey
22
EFLH1319
Direct-Drive N60 Tail Motor Heat Sink: BCPP2, BSR/Huey
33
EFLH1509
Main Gear: BSR/Huey
34
EFLH1510
Main Shaft Retaining Collar: BSR/Huey
35
EFLH1511
Swashplate: BSR/Huey
36
EFLH1512
Center Hub: BSR/Huey
37
EFLH1513
O-Ring & Shim Set: BSR/Huey
38
EFLH1514
Hardware Set: BSR/Huey
39
EFLH1515
Servo Pushrod Set: BSR/Huey
40
EFLH1516
3900Kv Brushless Motor: BSR/Huey
41
EFLH1517
Motor Mount: BSR/Huey
42
EFLH1524
Anti-Rotation Bracket/Guide: BSR/Huey
43
EFLH1525
Blade Grip Bolts: BCP/CPP/BSR/Huey
44
EFLRDS75H
7.5-Gram DS75 Digital Sub-Micro Helicopter Servo
45
EFLRG110HL
11.0-Gram G110 Micro Heading Lock Gyro
46
SPMAR6100EB
DSM2 6-CH Replacement Receiver for Blade Heli End Pin
Optional Part
Part #
EFLA625
Description
Light Kit SR UH-1 Huey
13
EN
©2011 Horizon Hobby, Inc.
US 7, 391, 320. Other patents pending.
Blade, DSM and DSM2 are trademarks or registered trademarks of Horizon Hobby, Inc.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Bell, Huey, and UH-1 Iroquois emblems, logos, and body designs are trademarks of Textron Innovations Inc. and are used under license by Horizon Hobby, Inc.
Created 8/11 32619.US BLH1700
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising