60-854 Printer Automation Module
SuperBus® 2000 Printer
or Automation Module
SuperBus 2000 Printer or Automation Module
Document Number: 466-1364 Rev. A
May 2000
PARALLEL
PRINTER
CONNECTOR
MODULE
POWER LED
BUS
STATUS LED
CIRCUIT CARD
OUTPUT SELECT
DIP SWITCH
UNIQUE SUPERBUS 2000
ID NUMBER LABEL
RS-232
SERIAL
CONNECTOR
(UNUSED)
PHAST
CONNECTORS
(2) (UNUSED)
ID: XXXXXXXX
60-626
8845G02A.DSF
8718G14A.dsf
WIRING TERMINALS
60-783, 60-854
RS-232 LED
(NOT USED)
8845g03b.dsf
Figure 1. Module Circuit Board Components
Installation
Instructions
Table 1. Module Component Descriptions
Component
Product Summary
Parallel Connector
Provides connection to a
parallel printer.
Power LED
Indicates module power
status.
Bus Status LED
Flashes to indicate normal
communication to the
panel bus.
Output Select DIP Switch
Selects output type.
RS-232 Status LED
Indicates RS-232 transmission. (Not used.)
Unique ID Number Label
Indicates module unique
identification number.
RS-232 Connector
Not used.
Supervised, fire-rated zone input.
PHAST Connectors
Not used.
On-board status indication.
Wiring Terminals
Used for panel SuperBus
and module zone input
connections.
The ITI® SuperBus® 2000 Printer Module allows you to
connect a parallel printer to any compatible system panel.
The module allows you to print (or log) selected system
events as they occur.
For additional security, a magnetic switch can be added and
connected to the built-in input zone to provide module
tamper protection.
Power for the module is provided by the system panel.
Features
O
O
O
O
O
Function
“Centronics™” type parallel printer output.
SuperBus 2000 automatic addressing data bus.
Two case styles:
60-783 - Plastic
60-854 - Metal
Installation Guidelines
Figure 1 shows the main module components and Table 1
describes them.
O
O
Do not exceed the panel total auxiliary output power
when using panel power for bus devices and hardwired
sensors that require panel power (see the specific panel
Installation Instructions).
Maximum current draw of the module (from the panel)
is 100 mA.
Page 1
SuperBus 2000 Printer or Automation Module
O
Use 4-conductor, 18-gauge or larger wire from the
module to the panel.
COVER
Tools and Supplies Needed
O
O
O
O
Small blade and Phillips screwdrivers
Drill and bits for screws and/or anchors
Case tamper switch and magnet (optional)
25-pin “Centronics” parallel printer cable
Plastic case accessory kit includes:
O
O
O
O
CARD LATCHES (2)
3/8-inch self-tapping screws
COVER SCREWS (2)
#6 panhead screws
BACKPLATE
CIRCUIT CARD
2K Ohm EOL resistor (49-467)
8845G1A.DSF
Wall anchors
Figure 2. Removing Plastic Case Cover and
Circuit Card
Metal case accessory kit includes:
O
O
O
O
1/4-inch plastic circuit board spacers (40-178)
3.
6 x 32 x 1/4-inch circuit board mounting screw (40006)
2K Ohm EOL resistor (49-467)
Place the module on the wall and mark the mounting
holes locations (Figure 3).
MOUNTING HOLES (4)
Door key lock and keys (40-577)
WIRE CHANNELS (3)
Installation
The plastic or metal cased module can be mounted on any
interior wall (protected from the elements).
Installing the Plastic Case Module
The plastic case module can be wall or gang-box mounted.
WIRE ACCESS (3)
CAUTION: You must be free of static electricity
before handling circuit boards. Wear a grounding strap or touch a bare metal surface to discharge static electricity.
CARD LATCHES (2)
ENCLOSURE BACKPLATE
(COVER AND CARD REMOVED)
8845G08A.DSF
Figure 3. Plastic Case Mounting Holes
To mount the plastic case module on a wall:
1.
2.
Page 2
Turn off panel power and disconnect backup battery(s).
Remove the module cover and circuit card and set
them aside (Figure 2).
4.
5.
6.
Drill the holes and insert the appropriate anchors.
Secure the back plate to the wall with panhead screws.
Snap the circuit card back into the back plate.
SuperBus 2000 Printer or Automation Module
Installing the Metal Case Module
BOARD MOUNTING SLOTS (3)
To mount the metal case module:
CASE MOUNTING HOLES (4)
CAUTION: You must be free of static electricity
before handling circuit boards. Wear a grounding strap or touch a bare metal surface to discharge static electricity.
1.
2.
3.
4.
5.
6.
Remove the metal case cover and module circuit board
and set them aside.
Hold the case against the mounting surface and mark
the four [larger] mounting holes.
Drill the mounting holes in the wall and insert the
appropriate anchors.
Remove case wiring knockouts as necessary.
Remove case rectangular connector knockout.
Secure the case to the wall with panhead screws.
Mounting the Module Board into the
Metal Case
8845G07A.DSF
Figure 5. Mounting the Board into Metal Case
To mount the board into the metal case:
1.
2.
3.
Snap the included 1/4 inch plastic spacers into the back
of the circuit board as shown in Figure 4.
Slide the board into the three board slots in the left side
of the enclosure as shown in Figure 5. Make sure the
connector fits through the case knockout.
Secure the board to the enclosure with the
included button head machine screw.
Mounting the Optional Key Lock
To mount the optional key lock into the metal
case:
1.
2.
3.
Remove the lock knockout from the panel door.
With the key in the lock, insert the lock into the knockout hole as shown in Figure 6.
Slide the lock clip onto the lock body as shown.
1/4 INCH PLASTIC SPACERS (2)
BACK OF
CIRCUIT BOARD
OPTIONAL
KEY LOCK
LOCK CLIP
8845G05A.DSF
Figure 4. Installing the Board Mounting Spacers
8845G06A.DSF
Figure 6. Optional Key Lock Mounting
Page 3
SuperBus 2000 Printer or Automation Module
Note: Other switch settings are not used.
3. Connect an input device (if used) to the module wiring
terminals as shown in Figure 8.
Advent Panel Wiring
This section describes how to wire the module to the Advent
panel and how to connect hardwire sensors to the module.
Refer to Figure 8 and Table 2 for wiring examples and connection descriptions.
To wire the module to the panel:
1.
2.
3.
4.
Make sure power is turned off to the panel.
Make sure the power transformer and backup
battery(s) are disconnected from the panel.
Wire the module to the panel SuperBus wiring harness
as shown in Figure 7.
Plug the wiring harness into the panel primary
SuperBus connector.
Installing a Case Tamper Switch
If the module is visible, you may want to add case tamper
detection. Then, if someone opens the cover, the switch
opens and causes an alarm.To add module case tampering,
install a magnet in the cover and a reed switch into the back
plate or case. Wire the switch to the module or one of the
panel zone inputs. (See Figure 8 or panel Installation
Instructions.)
Power Up and Bus Communication
SUPERBUS PRINTER
INTERFACE MODULE
TERMINAL STRIP
+12
VDC
BUS
A
BUS
B
GND
1
2
3
4
This section describes how to power up the panel and the
module and get them communicating with each other.
To power up the panel and the module:
1.
BLACK (GND)
WHITE (BUS B)
GREEN (BUS A)
RED (+12 VDC)
PANEL SUPERBUS
WIRING HARNESS 49-462
8543110A.DSF
Figure 7. Advent Panel SuperBus Wiring
2.
3.
Verify that all wiring at the panel and the module are
correct.
Reconnect the panel batteries and plug in the power
transformer. The module power LED should be on.
On initial power up, the panel automatically adds
(learns) the module into panel memory.
After a few seconds, the module bus status LED should
flash to indicate successful communication with the
panel.
If the module bus status LED does not flash, the module must be manually added (learned) into panel memory. (Refer to the panel Installation Instructions for
adding SuperBus modules.)
To connect a device to the module:
1.
2.
Attach the appropriate parallel printer cable to the connector on the module (Figure 8).
Connect an input device (if used) to the module wiring
terminals (Figure 8).
Setting the Output Select
DIP Switch
CAUTION: The module output select DIP switch
must be set before the module is powered up.
To set the DIP switch to “Printer:”
1.
2.
Page 4
Set switch 1 to “off” (down).
Set switch 2 to “on” (up).
Programming/Operating
the Module
Refer to the panel Installation Instructions for module
input/output programming and operation.
SuperBus 2000 Printer or Automation Module
PRINTER MODULE
CIRCUIT BOARD
UL-LISTED 25-PIN PARALLEL PRINTER
CABLE (CENTRONICS TYPE)
UL-LISTED
PARALLEL
PRINTER
PARALLEL
123456
TO PANEL
SUPERBUS
TERMINALS OR
WIRING HARNESS
(SEE OTHER
FIGURE OR TABLE)
+12 VDC
BUS A
BUS B
GND
ZONE 1
ZCOM
< OR >
UL-LISTED
NORMALLY
CLOSED (N/C)
CONTACTS
IN SERIES
UL-LISTED
NORMALLY
OPEN (N/O)
CONTACTS
IN PARALLEL
2K OHM EOL RESISTOR 49-467
(INSTALL AT LAST CONTACT)
8845g04b.dsf
Figure 8. Advent Panel/Module Wiring
Module Wiring Terminal Connections
Table 2. SuperBus 2000 Printer or Automation Module Terminal Connections
Page 5
SuperBus 2000 Printer or Automation Module
Testing
Specifications
To test the module:
Compatibility: Advent (and Custom Versions) fire/security
panels.
1.
2.
3.
Verify that all wiring at the panel and the module is
correct.
Connect panel AC transformer and backup battery.
Press * twice to return to the normal mode of operation
and test for proper parallel printer operation with the
selected system events.
Troubleshooting
Power Requirements: 12 VDC nominal, 100 mA
maximum draw from panel.
Panel Data Bus: ITI SuperBus auto addressing digital data
bus.
Parallel Printer Port: “Centronics” type (DB-25, female
connector).
Zone Input: One supervised, fire-rated zone.
Storage Temperature: -30° to 140° F (-34° to 60° C)
Module POWER LED stays off.
Check module and panel power.
Module BUS STATUS LED stays off.
1.
2.
Check SuperBus wiring and connections.
Check for proper panel/SuperBus module
programming and initialization.
Module BUS STATUS LED stays on.
1.
2.
Reinitialize panel and module by turning panel power
off and on.
Module circuit failure. Replace the module.
Module BUS STATUS LED blinks, but no printer operation.
1.
2.
3.
4.
5.
Check that the printer power is on.
Check for correct module DIP switch setting.
Note: If module DIP switch settings are changed
after initial power up, the module must be powered
down and back up. Then the module must be
deleted and then added (re-learned) into panel
memory (see panel Installation Instructions for
details).
Blinking LED indicates that the panel and module are
communicating correctly by way of the SuperBus.
Check module and device cables and connections.
Check panel/module programming.
Operating Temperature: 32° to 140° F (0° to 60° C)
Maximum Humidity: 85% relative humidity, noncondensing.
Approvals/Listings:
FCC Part 15
UL 365 for Police Connected Burglar Alarm Units and
Systems
UL 609 for Local Burglar Alarm Units and Systems
UL 864 for Control Units for Fire-Protective Signaling
Systems
UL 985 for Household Fire Warning System Units
UL 1023 for Household Burglar Alarm System Units
UL 1610 for Central Station Burglar Alarm System
Units
UL 1635 for Digital Alarm Communications System
Units
UL 1637 for Home Health Care Signaling Equipment
ULC Canada Commercial Fire/Burglary Warning
System (applied for)
CSFM California State Fire Marshall (applied for)
DOD Sensitive Compartment Information Fac. (applied for)
FM Factory Mutual (applied for)
MEA New York City Material Equipment Acceptance
(applied for)
Complies with NFPA 72 for National Fire Alarm
Code
Dimensions:
Plastic case: 6.0" x 8.5" x 1.5" (L x W x D).
Metal case: 11.25" x 9.75" x 4.63" (L x W x D).
Case Material:
60-783 - High-Impact, ABS plastic.
60-854 - 16 Gauge Steel.
Case Color:
60-783 - Belgian gray.
60-854 - “Fire” red.
Installation: Wall mount.
Page 6
SuperBus 2000 Printer or Automation Module
Notices
FCC Notices
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
• Install a quality radio or television outdoor antenna if the
indoor antenna is not adequate.
• Reorient or relocate the panel.
• Move the panel away from the affected equipment.
• Move the panel away from any wire runs to the affected
equipment.
• Connect the affected equipment and the panel to separate
outlets, on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for
help.
• Send for the FCC booklet How to Identify and Resolve RadioTV Interference Problems, available from the U.S. Government Printing Office, Washington, D.C. 20402. Stock Number: 004-000-00345-4.
Changes or modifications not expressly approved by Interactive
Technologies, Inc. can void the user’s authority to operate the
equipment.
Declaration of Conformity (DoC)
Interactive Technologies, Inc. declares that the ITI model no. 60792-95R is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
together. This precaution may be particularly important in rural
areas.
Caution: Users should not attempt to make such connections
themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
Notice: The Ringer Equivalence Number (REN) assigned to
each terminal device provides an indication of the maximum
number of terminals allowed to be connected to a telephone
interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the
sum of the Ringer Equivalence Number of all the devices does
not exceed 5.
AVIS D’INDUSTRIE CANADA
AVIS:
L’étiquette d’Industrie Canada identifie le matériel homologué.
Cette étiquette certifie que le matériel est conforme aux normes
de protection, d’ exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matérial terminal. Le
Ministere n’assure toutefois pas que le matériel fonctionnera à
la satisfaction de l’utilisateur.
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est
permis de le raccorder aux installations de l’enterprise locale de
télécommunication. Le matériel doit également être installé en
suivant une méthode acceptée de raccordement. L’abonné ne
doit pas oublier qu’il est possible que la conformité aux conditions énoncées ci-dessus n’empêche pas le dégradation du service dans certaines situations.
Les réparations de matériel homologué doivent être coordonnées par un représentant désigné par le fournisseur. L’entreprise
de télécommunications peut demander à l’utilisateur de
débrancher un appareil à la suite de réparations ou de modifications effectuées par l’utilisateur ou à cause de mauvais fonctionnement.
Pour sa propre protection, l’utilisateur doit s’assurer que tous les
fils de mise à la terre de la source d’énergie électrique, des
lignes téléphoniques et des canalisations d’eau métalliques, s’il y
en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.
Avertissment: L’utilisateur ne doit pas tenter de faire ces raccordements lui-meme; il doit avoir recours à un service d’inspection
des installations électriques, ou à électricien, selon le cas.
Industry Canada Warnings
Notice:
The Industry Canada Label identifies certified equipment. This
certification means that the equipment meets telecommunications network protective, operational, and safety requirements
as prescribed in the appropriate Terminal Equipment Technical
Requirement document(s). The Department does not guarantee
the equipment will operate to the user’s satisfaction.
In te r a c tiv e T e c h n o lo g ie s , In c .
2 2 6 6 S e c o n d S tre e t N o rth
N o r th S a in t P a u l, M N 5 5 1 0 9 - 2 9 0 0
T : 1 -8 0 0 -7 7 7 -1 4 1 5
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local telecommunications company. The equipment must also be
installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions,
may give the telecommunications company cause to request
the user to disconnect the equipment.
Users should ensure for their own protection that the electrical
ground connections of the power utility, telephone lines, and
internal metallic water pipe system, if present, are connected
F : 6 5 1 -7 7 9 -4 8 9 0
Security
Automation
Fire Protection
Access Control
ITI, Advent, and SuperBus are registered trademarks of
Interactive Technologies, Inc. Centronics is a trademark of
Centronics, Inc.
Page 7
SuperBus 2000 Printer or Automation Module
Page 8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising