OWNER’S MANUAL HOVERTRAX™ HOVERTRAX DLX™

OWNER’S MANUAL HOVERTRAX™ HOVERTRAX DLX™
HOVERTRAX™
HOVERTRAX DLX™
OWNER’S MANUAL
Read and understand this entire manual before using
this product! For assistance contact Razor.
DO NOT RETURN TO STORE.
NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.
Specifications subject to change without notice.
Please have your product along with the 19 character product I.D. code with you
before contacting Razor for warranty assistance and/or replacement parts.
Product I.D. Code: _____________ - ____________ - ____________
CONTENTS
Introduction ...................................................................................................... 1
Safety Warnings ...........................................................................................2-3
Pre-Ride Checklist ............................................................................................ 3
Before You Begin.............................................................................................. 4
Charging the Battery ........................................................................................ 5
Power Level Indicators ................................................................................ 5
How to Operate .............................................................................................6-8
Hovertrax Parts................................................................................................. 9
Warranty and Customer Service Contact Information................................... 10
INTRODUCTION
This manual will help you understand, set up and safely use the Razor® Hovertrax™. It is important that you adhere to all
safety warnings and cautions that appear throughout and that you use good judgment when riding, so keep reading!
A NEW TECHNOLOGY, WITH NEW
CONCEPTS FOR CONTROL AND SAFETY
As is obvious the first time you see it, the Razor Hovertrax is different from things you may have ridden before. No
handlebars. No front or rear wheel. No brake. It is new and it moves, which means if you are interested in riding it you
should be interested in learning how to do that properly – and if you are interested in minimizing the risk of falling off or
being injured, you should be very interested in focusing on how to ride this new product as safely as possible. Helping you
do that is the goal of this Manual and other warnings. THIS PRODUCT IS NEW, IT IS DIFFERENT, BUT IT MOVES
AND YOU MUST UNDERSTAND AND FOLLOW THE INSTRUCTIONS IN ORDER TO MAXIMIZE YOUR FUN AND
MINIMIZE RISKS OF INJURY PRESENTED BY RIDING THIS NEW MOVING PRODUCT.
MOVEMENT OF THE RAZOR HOVERTRAX IS CONTROLLED BY THE ANGLE OF THE FOOT PLATFORMS,
WHICH IS DETERMINED BY PRESSURE APPLIED BY THE RIDER’S FEET ON THE PLATFORMS.
Different? Well, yes, the Hovertrax is “different.” It is an electrically motorized, computerized, gyroscopically-balanceassisted, independently articulated, dual-platform two wheeled personal mobility system. If that sounds unlike any bicycle,
scooter, RipStik, roller skate or water ski you have ever used, you’re on the right track.
However, the Razor Hovertrax does not operate “magically” and it does not fly, float or disappear. It’s movements are
not controlled remotely, or by the rider’s brainwaves or earnest good wishes. And it has neither a steering wheel, nor
a brake, nor external stabilizers of any kind. Yet it can go, stop, turn and back up – and all of this is controlled solely by
the rider's feet moving at angles relative to the ground. THIS IS CRUCIAL TO RECOGNIZE AND TO REMEMBER AT
ALL TIMES. The angle of your feet – forward, level or rearward – on each foot platform is how Hovertrax
receives, processes and executes instructions from the rider. This will affect the operation of the Razor
Hovertrax far more than leaning or "shifting body weight" alone.
WARNING: Read this manual – including both "Safety Warnings" (pages 2-3) and "How to Operate" (pages 6-8)
and learn to ride safely!
1
SAFETY WARNINGS
WARNING: Whenever you ride the Hovertrax you risk serious injury or death from collisions, falls or loss of control. To ride
safely, YOU MUST READ AND FOLLOW THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL.
WARNING: Riding any electric product can be a hazardous activity.
Certain conditions may cause the equipment to fail without fault of the
manufacturer. Like other electric ride-on products, the Razor Hovertrax can and
is intended to move, and it is therefore possible to lose control, fall off and/or
get into dangerous situations that no amount of care, instruction or expertise
can eliminate. If such things occur you can be seriously injured or die, even
when using safety equipment and other precautions. RIDE AT YOUR OWN
RISK AND USE COMMON SENSE.
CHECK AND MAINTAIN RAZOR HOVERTRAX
WARNING: Always inspect the Razor Hovertrax prior to use.
Properly inspecting and maintaining your product can reduce the risk of injury.
Before use, check to confirm that any and all guards or covers are in place and
in serviceable condition. Check that the parts are functioning properly, that
the tires are not damaged or worn excessively. The Razor Hovertrax should be
maintained and repaired in accordance with the manufacturer’s specifications,
using only the manufacturer’s authorized replacement parts, and should not be
modified from the manufacturer’s original design and configuration. Replace
worn or broken parts immediately.
WARNING: Failure to read and understand "How to Operate"
section of this manual (pages 6-8) increases risk of injury due to falls or
other incidents.
Always check the battery charge before using the Razor Hovertrax. Do not
ride the Razor Hovertrax when its battery is low, as indicated by a solid red
indicator light or shaking of the wheels during operation. The Razor Hovertrax
may stop operating and cause you to fall.
WARNING: NOT FOR RIDERS UNDER AGE 13 OR HEAVIER
THAN 220 LB (100 KG). DO NOT EXCEED THE WEIGHT LIMIT OF 220 lb
(100 kg) – including backpacks and other items that might be carried.
Exceeding the weight limit could injure the rider and damage the Razor
Hovertrax. Rider weight alone also does not necessarily mean a person’s
size is appropriate to fit or maintain control of the Razor Hovertrax. Keep this
product away from small children and remember that this product is intended
for use only by persons who are, at a minimum, completely comfortable and
competent while operating the product.
WARNING: Check local laws and regulations to see where and
how you may use your Razor Hovertrax legally. Follow all applicable laws for
vehicles and pedestrians.
SAFETY GUIDELINES FOR CONTINUED USE:
An important message to all users
Razor recommends that children under the age of 13 not be permitted to
use this product. This recommendation is based not just on age or weight
or height – it reflects consideration of expected maturity and skills as well
as physical size. The recommended rider age of 13 years or older is only
an estimate and can be affected by the rider’s size, weight, or skills – not
every rider 13 years old or older will be suited to the product. Certainly, any
rider unable to fit comfortably on the Razor Hovertrax should not attempt
to ride it, but a parent’s decision to allow his or her child to ride this
product should be based on the child’s maturity, skill, and ability to
follow rules. Razor emphasizes that adults are strongly advised not to
disregard Razor’s recommendations or permit younger children to ride
the Razor Hovertrax.
Periodically review this information and make sure that you understand all
warnings, cautions, instructions and safety topics. Do not let others ride the
Razor Hovertrax until they have read this manual. Any type of wheeled activity
can be hazardous. Wheels can, and are intended to move and it is therefore
possible to get into dangerous situations and/or lose control and/or fall off. In
such situations serious injury or death could occur.
Always be aware of the activity around you. Use the Razor Hovertrax in areas
free from fixed or moving hazards. Watch your surroundings for pedestrians,
animals and riders of other wheeled devices.
Because products, like the Razor Hovertrax, can and do present potential
hazards plainly associated with their use, it is well recognized THE NEED FOR
EXERCISE OF PARENTAL RESPONSIBILITY IN SELECTING RIDING PRODUCTS
APPROPRIATE TO THE AGE OF A RIDER, OR PARENTAL SUPERVISION IN
SITUATIONS IN WHICH CHILDREN OF VARIOUS AGES MAY HAVE ACCESS
TO THE SAME RIDING PRODUCTS, IS IMPORTANT. Not every product is
appropriate for every age or size of rider, and recommendations are intended
to reflect the nature of the hazards and the expected mental or physical
ability, or both, of a rider to cope with the hazards.
WARNING: Only use the Razor Hovertrax indoors or on completely
smooth surfaces. Avoid obstacles and slippery surfaces, which could result in
a loss of balance or traction and cause a fall. See the section on Terrain for
more guidelines.
Persons with any mental or physical conditions that may make them
susceptible to injury, impair their physical dexterity or mental capabilities
to recognize, understand, and follow safety instructions, and to be able to
understand the hazards inherent in a product’s use, should not use or be
permitted to use products inappropriate for their abilities. Persons with heart
conditions, head, back or neck ailments (or prior surgeries to these areas of the
body), or pregnant women, should be cautioned not to operate this product.
Ride defensively. Watch out for potential obstacles that could catch your
wheel(s) or force you to swerve suddenly or lose control. Be careful to avoid
pedestrians, skaters, skateboards, scooters, bikes, children or animals who
may enter your path, and respect the rights and property of others.
WARNING: Do not lift the Razor Hovertrax off the ground when the
unit is turned on. Do not turn on the Razor Hovertrax in mid-air. This will cause
the wheels to spin freely which could result in injury to yourself or damage to
things around you.
Never carry passengers or allow more than one person at a time to ride the
electric product.
NOTICE: This manual contains many warnings and cautions concerning the consequences of failing to maintain, inspect or properly use your Razor Hovertrax
product. Because any incident can result in serious injury or even death, we do not repeat the warning of possible serious injury or death each time such a
possibility is mentioned.
2
SAFETY WARNINGS
USING THE CHARGER
The charger supplied with the electric product should be regularly examined
for damage to the cord, plug, enclosure and other parts. In the event of such
damage, the product must not be charged until the charger has been repaired
or replaced.
Never use headphones or a cell phone when riding. Never hitch a ride with
another product.
Do not ride the Razor Hovertrax in wet or icy weather and never immerse this
electric product in water, as the electrical and drive components could get
damaged by water or possibly create other unsafe conditions.
Use only with the recommended charger.
Wet, slick, bumpy, uneven or rough surfaces may increase risks. Do not
ride this electric product in mud, ice, puddles or water. Avoid excessive
speeds that can be associated with downhill rides. Never use near steps or
swimming pools.
Use caution when charging.
The charger is not a toy. Charger should be operated by an adult.
Do not operate charger near flammable materials.
Do not ride at night or when visibility is limited.
Unplug charger and disconnect from product when not in use.
Be careful and know your limitations. Risk of injury increases as the degree
of riding difficulty increases. The rider assumes all risk associated with
aggressive riding activities.
Always disconnect from the charger prior to wiping down and cleaning your
product with damp cloth.
WARNING: Never operate any moving product, including the Razor
Hovertrax, while under the influence of drugs or alcohol.
PROPER RIDING ATTIRE
Always wear proper protective equipment such as an approved safety
helmet (with chin strap securely buckled). A helmet may be legally required
by local law or regulation in your area. Elbow pads, kneepads, wrist guards,
a long-sleeved shirt, long pants and gloves are recommended. Always
wear athletic shoes (lace-up shoes with rubber soles) and keep shoelaces
tied and out of the way of the wheels, motor and drive system. Never ride
barefooted or in sandals.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS INCREASES RISK OF SERIOUS INJURY.
USE WITH APPROPRIATE CAUTION AND SERIOUS ATTENTION TO SAFE OPERATION.
PRE-RIDE CHECKLIST
Wheels
Safety Gear
Hardware/Loose Parts
Laws and Regulations
Practice riding only in wide open areas clear from curbs, parking
blocks and other obstacles, including things you may fall on or
into if you lose your balance. Impacting the wheels against any
hard surface can damage the wheels. Wheels are not covered
under your limited warranty.
Always wear proper protective gear, such as an approved safety
helmet. Elbow pads, kneepads and wrist guards are recommended.
Always wear athletic shoes (lace-up shoes with rubber soles) and
keep shoelaces tied and out of the way of the wheels, motor and
drive system. NEVER RIDE BAREFOOTED OR IN SANDALS.
Before every ride, check all parts, such as nuts, bolts, fasteners,
etc., to ensure they are secure and assembled correctly. There
should not be any unusual rattles or sounds from loose parts
or broken components. If the unit is damaged, do not ride.
Reference “Safety Warnings” on pages 2 and 3 of
this manual.
Always check and obey any local laws or regulations.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
3
BEFORE YOU BEGIN
Remove contents from box. Remove the separators that protect the components from damage during shipping. Inspect
the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping.
Because the Hovertrax was assembled and packed at the factory, there should not be any problems, even if the box has
a few scars or dents. Please keep this box in case you need to send the Hovertrax back for service or repairs. If you use
another box, Razor will not be responsible for any damage caused during shipping.
MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY MAINTENANCE PROCEDURES.
Estimated Set-Up Time
Allow up to 6 hours for initial charge (see page 5 for charging information).
WARNING:
DO NOT USE NON-RAZOR PARTS
WITH YOUR PRODUCT.
The Hovertrax has been built to
certain Razor design specifications.
The original equipment supplied
at the time of sale was selected
on the basis of its compatibility
with the frame and all other parts.
Certain aftermarket components
may not be compatible and will
void the warranty.
Product ID Locations:
See locations to the left
1. Frame (Underneath Unit)
On/Off Switch
2. Charger
Charge Port
Anti-Slip Foot Platforms
3. Box - Side of UPC (Not Shown)
Battery Power
Level Indicator
Balance Level
Indicator
Rubber Tires
Charger
(Note: Charger design may
vary from one shown)
Box Contents:
• Hovertrax
• Charger
• Owner’s Manual
2.
4
CHARGING THE BATTERY
Your Hovertrax comes with a built-in LiFeP04 (lithium ion phosphate) battery pack. Your Hovertrax may not have a fully
charged battery; therefore you must charge the battery prior to use. Be sure to charge the battery in a clean, dry location
away from direct sunlight, flames or sparks.
• Initial charge time: 6 hours.
• Make sure the Hovertrax power switch is turned OFF
when unit is not in use. If the power switch is left on
• Recharge time: up to 4 hours, even if the light turns green.
for an extended period of time, the battery may reach a
Recommended maximum charging time is 24 hours.
stage at which it will no longer hold a charge.
• Always charge the battery immediately after riding.
• Run time: Up to 115 minutes of continuous ride time.
• Fully charge battery before storing for extended periods
Run time may vary depending on riding conditions, rider
of time.
weight, climate, and/or proper maintenance.
• Unplug charger from the wall outlet when not in use.
• Constant stopping and starting may shorten ride time.
• Failure to recharge battery periodically may result in a
battery that will not accept a charge.
WARNING:
Use ONLY with the recommended
charger. Batteries are only to be
charged under adult supervision.
The charger is not a toy. Always
disconnect the charger before wiping
down and/or cleaning the Hovertrax
with a damp cloth.
The charger supplied with the
Hovertrax should be regularly
examined for damage to the cord,
plug, enclosure and other parts.
In the event of such damage, the
Hovertrax must not be charged until
it has been repaired or replaced.
Chargers have built-in overcharge
protection to prevent battery from
being overcharged.
Note: If the charger gets warm
during regular use, this is a normal
response and is no cause for
concern. If your charger does not get
warm during use, it does not mean
that it is not working properly.
Charger
Wall outlet - Green (stand by)
Wall outlet and unit - Red (charging)
Wall outlet and unit - Green (charged)
LED
Note: Make sure the power switch
is in the OFF position.
Note: Continue charging unit even if
light turns green prior to 3 hours.
2 Plug the charger into the charger
1 Plug the charger plug into wall
port on the Hovertrax. The light on
the charger should turn red during
charging. The light will turn green
again when charging is complete.
outlet. The light on the charger
should be green.
Note: If green light (LED) does not
turn on, try a different outlet.
Battery Power Level Indicators
• Solid Green: Battery power level is 15 to 100 percent.
• Flashing Green: Battery power level is 5 to 15 percent, recommend charging.
• Solid Red: Battery power level is below 5 percent. Do not ride and charge immediately.
WARNING: Failure to
recharge the battery at least once a
month may result in a battery that
will no longer accept a charge.
WARNING: The
Hovertrax will notify you when the
battery charge is dangerously low
by slowing down and shaking the
wheels when you are riding it. If
these warnings occur, immediately
slow down and safely step off.
Turn the product off. Do not
attempt to ride again until the
battery is recharged.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
5
HOW TO OPERATE
HOW IT WORKS
The Hovertrax responds to the rider's foot movements. Remember this. The Hovertrax moves due to fore and aft foot
platform tilt caused by the rider’s foot (or feet).
Movement, speed, and stopping are controlled by the degree to which the rider’s feet cause the foot platforms of the
Hovertrax to no longer be parallel to the ground.
When the product is “on”, the gyroscopic mechanized balancing feature of the Hovertrax tries to keep the foot platforms
of the product parallel to the ground. In use, Hovertrax then detects changes from "level" which are caused by fore
and aft pressure on the foot platform(s) applied by the rider’s feet. Such changes are interpreted by the Hovertrax as
instructions to make the wheels move. Hovertrax tries to re-level a forward tilt by accelerating, and tries to level a
rearward tilt by decelerating.
Note: Do not lift the Hovertrax off
the ground when it is turned on. Do
not turn on the Hovertrax in mid-air.
Moving and Changing Direction:
When a rider stands on the Hovertrax with an evenly weighted foot "level" on either foot platform:
• Pressing toes on both feet downward moves Hovertrax forward
• Pressing heels on both feet downward moves Hovertrax backward
• Turns are done by putting more downward pressure on the front side of the foot platform on the outside
of the turn.
• A rider can spin in place by pushing downward on the front edge of one foot platform while simultaneously
pushing downward on the rear edge of the other foot platform.
Accelerating and Stopping:
• To go faster or to slow down, press the foot platforms at a greater angle for “more” and reduce the angles
for “less”.
• When slowing or stopping, if you continue to apply force to the edges opposite the direction of travel, you may
not only stop but continue on to reverse your direction.
How does this happen? The fundamental principle is that the Hovertrax is designed to be “at rest” when the foot
platforms are level – and the gyroscopic mechanized balancing feature detects the “levelness” of the product. This
same feature detects foot movements which cause a foot platform to no longer be “level” and it interprets these
changes as orders to move.
That’s it. That’s how it works. It does what your feet tell it to do, and the product “self-balances” itself in order to be
ready to detect and implement the instructions provided by a rider’s feet.
Understanding this principle is important for obvious reasons. It also suggests some obvious warnings for riding the
Hovertrax, such as:
• Do not jump up and down on it: If you remove a foot (or both feet), if you then land back on the Hovertrax and
cause the foot platform(s) to change position relative to “level” in any degree, the machine could and will react by
moving immediately in response to an “instruction”, which can result in loss of rider stability, balance or control.
• Shifting Weight Alone is not the Issue: Do not presume that shifting weight alone controls motion – or, for
that matter, that not shifting weight equals “stability”. Shifting of rider weight may be associated with increase or
decrease of foot pressures on the foot platforms, but it is the action of the feet on the foot platforms which instructs
Hovertrax to move. Conversely, if you were to shift your weight without altering the placement or angle of your feet,
so that the foot platforms remain level, the Hovertrax does not receive any “signal” to interpret.
HOW TO GET ON
Once you have charged the battery (see page 5 for charging information):
1. Power On: Set the Hovertrax on the ground and turn the power on. The green light on the top of the unit will light
up. The Hovertrax can face in either direction.
2. First Foot: While standing behind the Hovertrax, put one foot on a foot platform, closer to the wheel than to the
center. Use that foot to activate the foot platform by bringing that foot platform to a balanced, level position.
3. Confirm Activation: Confirm the first foot platform is activated. Move your foot back and forth and feel the
response from the unit. Play with this single foot platform until you are comfortable keeping the foot platform
motion minimal.
4. Step Up: With the first foot platform stable and still, step up on the second foot platform with your second foot.
Do this away from furniture and other large objects. Don’t use a fixed object to brace or lift yourself – Keep your
weight evenly distributed between the two foot platforms. If you are uncomfortable; step back off and repeat from
step 2. Try to stand on the Hovertrax without moving.
6
Riding Tip: Certainly the rider may
"lean" on the Hovertrax, but leaning
only affects the foot platform's
position to the extent the rider's feet
change their position. If the rider's
ankles are held at a consistent 90°
angle, leaning will result in tilting.
Note that leaning can exaggerate
shifting of weight, which may affect
the ability of a rider to recover to
a level posture – increasing the
possibility of loss of balance.
Riding Tip: Before your very
first ride, expect to spend up
to ten minutes in this stage
of learning how to stand
comfortably on the Hovertrax.
HOW TO OPERATE
HOW TO RIDE:
5. Stand in Place: Hovertrax is unique among two-wheeled items in that the active stabilization it provides allows
you to stand in place. A scooter or bicycle may balance more easily when it moves, but a Hovertrax can balance
even while stationary.
6. Move Forward: To move forward, press down gradually with your feet on the fronts of both foot platforms. Do not
lunge forward or lean excessively, as you may lose your balance.
7. Slow Down: To slow down or stop, apply pressure to the rear edges of the foot platforms by pushing down with
your heels. Leaning back somewhat may be useful but remember your feet are giving the instructions! If you
continue pushing the rear edges with your heels, you will be able to travel backwards.
8. Turn: To turn right, slightly push your right foot down on the front of the right foot platform; to turn left, push down
on the front of the left foot platform. This idea is to make one wheel turn a little bit faster than the other wheel.
9. Rotate in Place: To rotate in place, push down on the front of one foot platform while pushing down with equal
force on the rear of the other foot platform.
Riding Tip: Your practice on
Hovertrax should be to keep
the platform in place and get
a feel for the motions that are
generated from small changes in
your fore/aft foot pressure.
HOVERTRAX SPEED CONTROL
10. Not too fast: The recommended top speed of the Hovertrax is approximately six miles per hour (9 km/hr). Speed
may be affected by rider weight, surface conditions, battery charge, etc. The Hovertrax has a “limiter” feature
which may engage to warn against further acceleration beyond recommended levels. This safety feature causes
the front edge of the foot platforms to "push back" against the rider's feet to caution about excessive speed. Do not
attempt to override this safety feature by continuing acceleration because risks of falling may greatly increase.
HOW TO GET OFF:
11. Slow down and stop
12. Step to the back
13. Power down
PRODUCT WARNING SIGNALS
The Hovertrax has several built in protection features, which include:
• Level alert: if the product is not level enough for the balancing feature to engage, a level indicator light will turn red
and the product will not be operable until properly level.
• Low or charging battery: The battery indicator light will indicate insufficient charge for operation by turning red.
• Excessive angle shutoff: At excessively steep foot platform angles, the unit will stop powered operation.
RIDING TIPS
• Learn to ride the Hovertrax in a large, safe area free from all forms of interference.
• Keep your posture upright, but relaxed. Align your body over the Hovertrax and use a wide stance with your feet close
to the wheels.
• Be alert. Scan both far ahead and in front of you - your eyes are your best tool for safely avoiding obstacles and
slippery surfaces.
• Hold your arms comfortably at your side.
• Start at a slow and comfortable pace. Never aggressively accelerate or lunge forward.
• Be careful and considerate of others.
• Always ride under control at a speed that is safe for you and those around you.
• Always be prepared to stop.
• Respect pedestrians by always yielding the right of way.
• Avoid startling pedestrians. When approaching from behind, announce yourself and slow down to walking speed
when passing. Pass on the left whenever possible. When approaching a pedestrian from the front, stay to the right
and slow down.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
7
HOW TO OPERATE
HOVERTRAX TIPS
Once you have charged the battery, follow these six easy steps:
• Remember to check for the green battery indicator light before you get on. If it is not lit, the unit is not on and you
will fall.
• Do not stand on or near the center or rotating portion of the foot platform.
• Remember to keep your body relaxed through your back and legs. Stand naturally.
• Practice controlled stopping.
• If you stand with one foot on the foot platform with the unit on, keep that foot level, or the Hovertrax will move.
• Be aware of the width of the Hovertrax and the path you are traveling. Make sure you will fit.
TERRAIN AND AVOIDING HAZARDS, SLIPS AND TRIPS
The Hovertrax is intended for indoors or use on smooth, flat surfaces. However, to prevent loss of traction, you must
always be careful when riding and learn to identify and avoid slippery and wet surfaces, loose materials, slopes,
potholes and other obstacles.
Stop and step off the Hovertrax over unsafe surfaces or terrain.
The Hovertrax wheels must be able to grip the ground for you to stay upright. Slips occur when the Hovertrax loses
traction, potentially causing loss of control and a fall. Abrupt maneuvers and riding over slippery surfaces, bumps, and
loose objects and materials may cause the Hovertrax to lose traction.
• Keep alert.
• Never jump on or off the Hovertrax with both feet.
• Please don’t ride transversely on a hillside or turn on a slope. This may cause Hovertrax's balance sensors to be
unable to orient themselves to "level" state, impairing rider control.
• Avoid riding over any surface where the undercarriage may strike an object.
• Use caution when riding over any change in terrain.
8
HOVERTRAX PARTS
Keep your Hovertrax running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability.
(Specifications subject to change without notice.)
1. Rubber Footplate
1-1 Footplate support
2. LED Indicator Cover
3. Warning Indicator LED
4. Battery Indicator LED
5. Plastic Cover (Top) (Right/Left)
6. Headlight (Left) (Hovertrax DLX only)
6-1 Headlight Cover (Left)
7. Headlight (Right) (Hovertrax DLX only)
7-1 Headlight Cover (Right)
8. Charger Port
9. On/Off Switch
10. Wheel w/ Hub Motor (Right/Left)
11. Torsion Bar
11-1 C-clip (x2)
11-2 Washer (x2)
12.
13.
14.
15.
16.
17.
18.
15
Control Module
Battery (36V)
Lock Block for Hub Motor (x2)
Plastic Cover (Induction Contactor)
Bottom Cover (Left)
Bottom Cover (Right)
36V Charger (Not Shown)
15
13-1
13
10
10
11-1
14
11-2
12
14
11
8
9
16
17
6-1
6
7
7-1
5
4
3
2
1
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
9
WARRANTY
Razor Limited Warranty
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
The manufacturer warranties this product to be free of manufacturing defects
for a period of 90 days from date of purchase. This Limited Warranty does not
cover normal wear and tear, tires, tubes or cables, or any damage, failure or
loss caused by improper assembly, maintenance, storage or use of the Razor
Hovertrax and Hovertrax DLX.
Razor does not offer an extended warranty. If you have purchased an extended
warranty, it must be honored by the store at which it was purchased.
For your records, save your original sales receipt with this manual and write
the serial number below.
This Limited Warranty will be void if the product is ever:
• used in a manner other than for recreation or transportation;
• modified in any way;
• rented.
__________________________________________
NOTICE: INSURANCE
YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR
ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC
RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED,
YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
CUSTOMER SERVICE CONTACT INFORMATION
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed below:
AMERICAS
EUROPE
ASIA
Razor USA LLC
P.O. Box 3610
Cerritos, CA 90703
USA
Razor USA LLC (Europe)
Handelsweg 2
2742 RD Waddinxveen
Netherlands
Razor USA LLC (Asia)
P.O. Box 3610
Cerritos, CA 90703
USA
+1 866 467 2967
Monday - Friday
8:00 AM - 5:00 PM Pacific Time
+44 (0) 120 267 2702
+81 50 7579 6622
info@razor-asia.com
DISTRIBUTED IN THE UK BY:
DISTRIBUTED IN AUSTRALIA BY:
Re:creation Limited
2 Meadows Business Park
Station Approach, Blackwater
Camberley, Surrey GU17 9AB
United Kingdom
Funtastic Limited
Level 2, Tower 2, Chadstone Place
1341 Dandenong Road
Chadstone VIC 3148
Australia
+44 (0) 118 973 6222 Tel
+44 (0) 118 973 6220 Fax
sales@recreationltd.co.uk
+1 800 244 543
info@funtastic.com.au
US Patent No.: 8,738,278
Chinese Patent No.: CN203158157
Printed in China for Razor USA LLC.
Copyright © 2003-2015 Razor USA LLC. All rights reserved. Razor® and the Razor logo design are
among the registered trademarks of Razor USA LLC in the United States and/or select foreign
countries. Patents and Hovertrax™ trademark licensed from Inventist, Inc.
10
US_151124
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising