I-P-190: P190 Valve Guide Hone Set

I-P-190: P190 Valve Guide Hone Set
I-P-190B
SPECIAL INSTRUCTIONS
for
P-190 VALVE GUIDE HONE SET
http://www.sunnen.com
GENERAL
Sunnen P-190 Valve Guide Hone Set is designed for
sizing and finishing holes in work too bulky or
heavy to take to your honing machine. It uses the
same mandrels and stones used in Sunnen Honing
Machines. The Adapters listed in Table 1 must be
used as they are different from the adapters used in
Sunnen Honing Machines.
INSTALLATION
To install, proceed as follows:
1. Select correct Mandrel, Sleeve, Stone, Adapter,
and Wedge and assemble to P-190 (see Table 1).
2. Mandrels used with P-190 Valve Guide Set are
supplied with a standard Wedge for use in Sunnen
Honing Machine. To use wedges not supplied, alter
it as shown (see Figure 1).
NOTE: PBL8-W, PBL10-W, and PBL12-W Wedges
(included in P-190 Kit) have already been altered.
3. Snap altered Wedge into Feed Block as shown
(see Figure 2).
FIGURE 1
5. Insert Mandrel into Adapter with Wedge and
Stone Retainer side by side and tighten setscrew
(see Figure 3B, next page).
6. Place Stone in Mandrel (see Figure 3C, next
page).
NOTE: If Wedge sticks out too far, retract it by
turning Stone Feed-Up Knob counterclockwise (see
Figure 4, next page).
4. Attach Adapter to P-180 Head with 2 Capscrews
(see Figure 3A, next page).
INSERT ALTERED WEDGE BY PUSHING IT
STRAIGHT IN AGAINST INCLINED SURFACE OF
FEED BLOCK WHICH COMPRESSES SPRING CLIP
AND ALLOWS WEDGE TO SNAP INTO SLOT.
TO REMOVE WEDGE, PUSH DOWN
ON END AND PULL STRAIGHT OUT.
SPRING CLIP
FIGURE 2
TABLE 1, Valve Guide Hone Set
NOMINAL
FRACTIONAL SIZE
5/16
11/32
3/8
13/32
7/16
1/2
9/16
5/8
21/32
11/16
3/4
RANGE
inches
.308-316
.339-347
.370-385
.400-416
.432-447
.495-526
.557-588
.619-650
.650-681
.681-713
.744-775
millimeters
7.8- 8.0
8.6- 8.8
9.4- 9.8
10.2-10.6
11.0-11.4
12.6-13.4
14.1-14.9
15.7-16.5
16.5-17.3
17.3-18.1
18.9-19.7
1
MANDREL
BL10-308AS
BL10-339AS
BL12-370AS
BL12-400AS
BL12-432AS
BL16-495AS
BL16-557AS
BL16-619AS
BL16-650AS
BL16-681AS
BAL20-744LA*
2
SLEEVE
S-308
S-339
S-370
S-400
S-432
S-495
S-557
S-619
S-650
S-681
S-744
*This is a replaceable shoe type mandrel. Replacement shoe Part No. LA-C (2 required).
“SUNNEN HONALL, SUNNEN AND THE SUNNEN LOGO ARE REGISTERED TRADEMARKS OF SUNNEN PRODUCTS COMPANY.”
3
STONE
L10-J69
L10-J69
L12-J67
L12-J67
L12-J67
L16-J67
L16-J67
L20-J67
L20-J67
L20-J67
L20-J67
4
ADAPTER
PK10-A
PK10-A
PK12-A
PK12-A
PK12-A
PK16-A
PK16-A
PK20-A
PK20-A
PK20-A
PAK20-A
5
WEDGE
BL-10W
BL-10W
BL-12W
BL-12W
BL-12W
BL-16W
BL-16W
BL-16W
BL-16W
BL-16W
BL-20W
FIGURE 3
FIGURE 4
“SUNNEN HONALL, SUNNEN AND THE SUNNEN LOGO ARE REGISTERED TRADEMARKS OF SUNNEN PRODUCTS COMPANY.”
Sunnen® reserves the right to change or
revise specifications and product design
in connection with any feature of our
products contained herein. Such changes
do not entitle the buyer to corresponding
changes, improvements, additions, or
replacements for equipment, supplies or
accessories previously sold. Information
contained herein is considered to be
accurate based on available information
at the time of printing. Should any
discrepancy of information arise, Sunnen
recommends that user verify discrepancy
with Sunnen before proceeding.
PRINTED IN U.S.A.
0602
SUNNEN PRODUCTS LIMITED
No. 1 Centro, Maxted Road
Hemel Hempstead, Herts HP2 7EF ENGLAND
Phone: ++ 44 1442 39 39 39
Fax: ++ 44 1442 39 12 12
www.sunnen.co.uk
e-mail: hemel@sunnen.co.uk
SUNNEN AG
SUNNEN PRODUCTS COMPANY
7910 Manchester Ave., St. Louis, MO 63143 U.S.A.
Phone: 314-781-2100
Fax: 314-781-2268
U.S.A. Toll-Free Sales and Service –
Automotive: 1-800-772-2878 • Industrial: 1-800-325-3670
International Division Fax: 314-781-6128
Fabrikstrasse 1
8586 Ennetaach-Erlen, Switzerland
Phone: ++ 41 71 649 33 33
Fax: ++ 41 71 649 34 34
www.sunnen.ch
e-mail: info@sunnen.ch
SHANGHAI SUNNEN MECHANICAL CO., LTD.
889 Kang Qiao East Road, PuDong
Shanghai 201319, P.R. China
Phone: 86 21 5 813 3322
Fax: 86 21 5 813 2299
www.sunnensh.com
e-mail: sales@sunnensh.com
SUNNEN ITALIA S.R.L.
http://www.sunnen.com
e-mail: sunnen@sunnen.com
Viale Stelvio 12/15
20021 Ospiate di Bollate (MI) Italy
Phone: 39 02 383 417 1
Fax: 39 02 383 417 50
www.sunnenitalia.com
e-mail: sunnen@sunnenitalia.com
©COPYRIGHT SUNNEN® PRODUCTS COMPANY 2006, ALL RIGHTS RESERVED
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising