datasheet for OTS-S5-0710-00-10-FA-12-1-35

datasheet for OTS-S5-0710-00-10-FA-12-1-35
Optiva OTS-2: X-Band
RF Fiber Optic Transport System
DATASHEET | JUNE 2013
SATCOM
X-Band RF Fiber Optic Transport System
The Optiva OTS-2 X-Band transmitter and receiver are ideal to
construct 7.000 to 10.000 GHz transparent fiber optic links for
antenna remoting, electronic warfare systems, broadband delay
lines, signal processing systems and other high-dynamic-range
applications.
Optiva satellite and microwave transmitters and receivers are
SNMP compliant. They can be housed in the same chassis and monitored by the
same Network Management System (NMS) as Optiva HD video, audio, serial data,
and USB extension / distribution cards to provide multiple format and frequency
Applications
„ Satcom X-Band Antenna Signal Distribution
„ Ground Terminal & Intra-Facility Links
„ Site Diversity Systems
transport in a single flexible platform.
System Design
The Optiva platform includes a wide range fiber
optic transport products for satellite and microwave
„ Electronic Warfare (EW) Systems
communications from 1 MHz to 40 GHz. These units can be used to construct
„ Broadband Delay Line and Signal Processing
Systems
transparent inter- and intra-facility links from 1 meter to >100 km for RF and
microwave signal transport, antenna remoting, video transport, electronic
warfare systems and other high-dynamic-range applications.
Features / Benefits
Optiva is a completely modular, hot-swappable platform. Both 19” rack-mount
„ X-Band Link - Eliminates the performance and
cost penalty of block conversion
and compact tabletop, or wall-mountable enclosures are available. The 3RU 19”
„ Low RIN Source Laser - Provides highdynamic-range of >102 dB Hz2/3.
up to 16 insert cards and utilize two dual-redundant, hot-swappable, 100 or 200
„ Microprocessor-Based Transmitter Control
for Laser Bias, Modulator Bias & Link Gain
- Provides consistent high performance
operation and allows for modulator low-bias
operation and SFDR >102 dB Hz2/3
CC-6-1U) can accommodate 6 insert cards and utilizes two hot-swappable 60 watt
„ SNMP V.1 and RS-232 Monitor & Control
Interface - Flexible user interface options
Enclosure Options
rack-mount, fan-cooled enclosures (Model OT-CC-16 and OT-CC-16F) can support
watt power supplies. The 1RU 19” rack-mount, fan-cooled enclosure (Model: OTpower supplies. Compact one-slot (OT-DTCR-1), or two-slot (OT-DTCR-2) enclosures
are also available that use an external wall-mount power supply.
„ Compatible with EMCORE’s Modular Optiva
Platform - Allows multiple format and
frequency transport in a single chassis
„ DWDM Operation - Increases transport
capacity without increasing fiber count
© 2013 EMCORE Corporation | REV 2013.06
626-293-3400
satcom-sales@emcore.com
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
Optiva OTS-2: X-Band
RF Fiber Optic Transport System
DATASHEET | JUNE 2013
SATCOM
Performance Highlights
Parameter
Frequency Range
RF Input Power
Min
Typical
Max
Units
7.000
-
10.000
GHz
-
-
5*
dBm
-15^
Wavelength
-
1550
Optical Output Power
9
10
11
dBmo
-10
-
50
°C
Operating Temperature Range
-
nm
*TX: RF amp 15 dB gain, attenuation range 0 to 15 dB
^TX: RF amp 35 dB gain, attenuation range 0 to 15 dB
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only.
Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of the
datasheet. Exposure to absolute maximum ratings for extended periods can adversely affect device reliability.
Symbol
Min
Max
Units
Operating Temperature
Parameter
TOP
-20
60
°C
Storage Temperature
TSTG
-40
85
°C
RF Input
Sin
NA
5*
dBm
-15^
*TX: RF amp 15 dB gain
^TX: RF amp 35 dB gain
Transmitter & Receiver Block Diagram
*
*
*50 Ω SMA female connectors
© 2013 EMCORE Corporation | REV 2013.06
626-293-3400
satcom-sales@emcore.com
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
Optiva OTS-2: X-Band
RF Fiber Optic Transport System
DATASHEET | JUNE 2013
SATCOM
Transmitter & Receiver Optical Characteristics
Parameter
Symbol
Condition
Min
Typical
Max
Units
Wavelength
l
-
1530
1550
1562
nm
Optical Output Power
PL
-
9
10
11
dBmo
Connector Return Loss
-
-
40
-
-
dB
Optical Connector Type
-
SC/APC
-
-
-
-
Pin
-
-
-
+10
dBmo
-
0.7
-
-
A/W
Receiver Optical Input Power
Receiver Responsivity
-
Note: In order to prevent reflection-induced distortion degradation, the laser should be connected to an optical cable having a return loss of at least 55 dB for discrete reflections
and 30 dB for distributed reflections.
X-Band Transmitter & Receiver RF Characteristics
Condition
Min
Typical
Max
Units
Operational Bandwidth
Parameter
-
7.0
-
10.0
GHz
RF Input Impedance
-
-
50
-
RF Return Loss
-
-
-
-15
dB
-22
dB
RF Connectors
SMA Female
RF Test Point Reference Value, Relative to RF input or RF output*
-18
-
-20
*Test point performance beyond the stated frequency range is provided; only the test point reference value tolerance may increase beyond the above stated +/- 1 dB
DC Power Consumption - Max
Module Type
Input Voltage (VDC)
Max Current (@+70°C)
Transmitter
+12
1A
Receiver
+12
750 mA
Environmental Specifications
Parameter
Operating Temperature
Operating Humidity, Maximum Non-Condensing
Operating Altitude, Above Sea Level
Symbol
Min
Max
Units
TOP
-10
50
°C
--
--
95%
--
--
6000
ft
TSTG
-40
70
°C
Storage Humidity, Maximum Non-Condensing
--
--
95%
--
Storage Altitude, Above Sea Level
--
--
50,000
ft
Storage Temperature
© 2013 EMCORE Corporation | REV 2013.06
626-293-3400
satcom-sales@emcore.com
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
Optiva OTS-2: X-Band
RF Fiber Optic Transport System
DATASHEET | JUNE 2013
SATCOM
Link Performance - X-Band
Parameter
Symbol
Condition
Min
RF Bandwidth
-
-
Link Gain (+0 dBmo RX optical input)*^
G
@ 7.0 GHz
G
Link Gain (+10 dBmo RX optical input)*^
Noise Figure (+0 dBmo RX optical input)^
Noise Figure (+10 dBmo RX optical input)^
Input IP3^
Spurious Free Dynamic Range^
Gain Variation
Typical
Max
Units
7.000
-
10.000
GHz
-4
0
-
dB
@ 10.0 GHz
-4
0
-
dB
G
@ 7.0 GHz
16
20
-
dB
G
@ 10.0 GHz
16
20
-
dB
NF
@ 7.0 GHz
12
-
-
dB
NF
@ 10.0 GHzz
12
-
-
dB
NF
@ 7.0 GHz
7
-
-
dB
NF
@ 10.0 GHz
7
-
-
dB
IIP3
@ 7.0 GHz
-
-6
-
dBm
IIP3
@ 10.0 GHz
-
-5
-
dBm
SFDR
@ 0 dBmo RX Optical Input
101
-
-
dB-Hz2/3
SFDR
@ +10 dBmo RX Optical Input
105
-
-
dB-Hz2/3
-
Any 36 MHz
-
-
0.5
dB
-
Any 500 MHz
-
-
1.5
dB
*Receiver RF output will change 2 dB for each 1 dB of RX optical input power level change
^Performance based on OTS-2T/S5 with RF Amp gain of 35 dB, OTS-2R/S5 with RF Amp gain of 15 dB
Typical X-Band Downlink S21 Frequency Response
Network Management
All modules are compliant with SNMP v.1 supported through the Optiva NMS card (OPV-CTLR-IC)
© 2013 EMCORE Corporation | REV 2013.06
626-293-3400
satcom-sales@emcore.com
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
Optiva OTS-2: X-Band
RF Fiber Optic Transport System
DATASHEET | JUNE 2013
SATCOM
Ordering Information: Transmitter
Transmitter
OTS-2T / S5-0710-WW-10-XX-12-YY-Z
„ When ordering replace “WW” with one of the ITU Channel Options
„ When ordering replace “XX” with one of the Optical Connector Options
„ When ordering replace “YY” with one of the Variable Gain RF Amplifier Options
„ When ordering replace “Z” with one of the Enclosure Options
RF Connector
S5 = 50 Ω SMA
X-Band Frequency
(GHz)
0710 = 7.000-10.000
GHz
ITU Channel Options
(THz / nm)
“WW”
Optical Power
(dBmo)
Standard:
00 = non-ITU: 1520-1580 nm
10 = +10 Optical
Output
Optical
Connector
Options
“XX”
Standard:
SA = SC / APC
Optical Output +
RF Test Port (dB)
Variable Gain
RF Amplifier
Options (dB)
“YY”
1 = Single Optical Output +
2 = -20 dB Test Port
15 = 15 dB
35 = 35 dB
Optional:
18 = 191.8 THz/1563.05 nm
19 = 191.9 THz/1562.23 nm
20 = 192 THz/1561.42 nm
21 = 192.1 THz/1560.61 nm
22 = 192.2 THz/1559.79 nm
23 = 192.3 THz/1558.98 nm
24 = 192.4 THz/1558.17 nm
25 = 192.5 THz/1557.36 nm
26 = 192.6 THz/1556.56 nm
27 = 192.7 THz/1555.75 nm
28 = 192.8 THz/1554.94 nm
29 = 192.9 THz/1554.13 nm
30 = 193 THz/1553.33 nm
31 = 193.1 THz/1552.52 nm
32 = 193.2 THz/1551.72 nm
33 = 193.3 THz/1550.92 nm
34 = 193.4 THz/1550.12 nm
35 = 193.5 THz/1549.32 nm
36 = 193.6 THz/1548.51 nm
37 = 193.7 THz/1547.72 nm
38 = 193.8 THz/1546.92 nm
39 = 193.9 THz/1546.12 nm
40 = 194 THz/1545.32 nm
41 = 194.1 THz/1544.53 nm
42 = 194.2 THz/1543.73 nm
43 = 194.3 THz/1542.94 nm
44 = 194.4 THz/1542.14 nm
45 = 194.5 THz/1541.35 nm
46 = 194.6 THz/1540.56 nm
47 = 194.7 THz/1539.77 nm
48 = 194.8 THz/1538.98 nm
49 = 194.9 THz/1538.19 nm
50 = 195 THz/1537.4 nm
51 = 195.1 THz/1536.61 nm
52 = 195.2 THz/1535.82 nm
53 = 195.3 THz/1535.04 nm
54 = 195.4 THz/1534.25 nm
55 = 195.5 THz/1533.46 nm
56 = 195.6 THz/1532.68 nm
57 = 195.7 THz/1531.9 nm
58 = 195.8 THz/1531.12 nm
59 = 195.9 THz/1530.33 nm
60 = 196 THz/1529.55 nm
61 = 196.1 THz/1528.77 nm
62 = 196.2 THz/1527.99 nm
© 2013 EMCORE Corporation | REV 2013.06
Optional:
FA = FC / APC
EA = E2000 / APC
626-293-3400
Enclosure Options
“Z”
1 = Optiva Indoor
Rack Mount
Installation
2 = Optiva Outdoor
MiniHub Installation
satcom-sales@emcore.com
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
Optiva OTS-2: X-Band
RF Fiber Optic Transport System
DATASHEET | JUNE 2013
SATCOM
Ordering Information: Receiver
Receiver
OTS-2R / S5-0710-10-WW-XX-2-YY-Z
„ When ordering replace “WW” with one of the Optical Connector Options
„ When ordering replace “XX” with one of the ITU Channel Options
„ When ordering replace “YY” with one of the Variable Gain RF Amplifier Options
„ When ordering replace “Z” with one of the Enclosure Options
ITU Filter Options
for Improved Optical
Isolation in DWDM
Systems (THz / nm)
“XX”
RF Connector
X-Band Frequency
(GHz)
Optical Power (dBmo)
Optical
Connector
Options
“WW”
S5 = 50 Ω SMA
0710 = 7.000-10.000
GHz
10 = +10 Max Optical
Input
Standard:
SA = SC / APC
Standard:
00 = No filter
Optional:
FA = FC / APC
EA = E2000 / APC
Optional:
18 = 191.8 THz/1563.05 nm
19 = 191.9 THz/1562.23 nm
20 = 192 THz/1561.42 nm
21 = 192.1 THz/1560.61 nm
22 = 192.2 THz/1559.79 nm
23 = 192.3 THz/1558.98 nm
24 = 192.4 THz/1558.17 nm
25 = 192.5 THz/1557.36 nm
26 = 192.6 THz/1556.56 nm
27 = 192.7 THz/1555.75 nm
28 = 192.8 THz/1554.94 nm
29 = 192.9 THz/1554.13 nm
30 = 193 THz/1553.33 nm
31 = 193.1 THz/1552.52 nm
32 = 193.2 THz/1551.72 nm
33 = 193.3 THz/1550.92 nm
34 = 193.4 THz/1550.12 nm
35 = 193.5 THz/1549.32 nm
36 = 193.6 THz/1548.51 nm
37 = 193.7 THz/1547.72 nm
38 = 193.8 THz/1546.92 nm
39 = 193.9 THz/1546.12 nm
40 = 194 THz/1545.32 nm
41 = 194.1 THz/1544.53 nm
42 = 194.2 THz/1543.73 nm
43 = 194.3 THz/1542.94 nm
44 = 194.4 THz/1542.14 nm
45 = 194.5 THz/1541.35 nm
46 = 194.6 THz/1540.56 nm
47 = 194.7 THz/1539.77 nm
48 = 194.8 THz/1538.98 nm
49 = 194.9 THz/1538.19 nm
50 = 195 THz/1537.4 nm
51 = 195.1 THz/1536.61 nm
52 = 195.2 THz/1535.82 nm
53 = 195.3 THz/1535.04 nm
54 = 195.4 THz/1534.25 nm
55 = 195.5 THz/1533.46 nm
56 = 195.6 THz/1532.68 nm
57 = 195.7 THz/1531.9 nm
58 = 195.8 THz/1531.12 nm
59 = 195.9 THz/1530.33 nm
60 = 196 THz/1529.55 nm
61 = 196.1 THz/1528.77 nm
62 = 196.2 THz/1527.99 nm
Test Port (dB)
Variable Gain
RF Amplifier
Options (dB)
“YY”
2 = -20 dB Test Port
15 = 15 dB
Enclosure Options
“Z”
1 = Optiva Indoor Rack
Mount Installation
35 = 35 dB
© 2013 EMCORE Corporation | REV 2013.06
626-293-3400
2 = Optiva Outdoor MiniHub
Installation
satcom-sales@emcore.com
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
Optiva OTS-2: X-Band
RF Fiber Optic Transport System
DATASHEET | JUNE 2013
SATCOM
Mechanical Configuration
Each Transmitter and Receiver module occupies two slots in the EMCORE Optiva Chassis.
Laser Safety
This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH Class 1M laser
product. All versions of this laser are Class 1M laser product, tested according to IEC 60825-1:2007 / EN 60825-1:2007. An
additional warning for Class 1M laser products. For diverging beams, this warning shall state that viewing the laser output
with certain optical instruments (for example: eye loupes, magnifiers, and microscopes) within a distance of 100 mm may
pose an eye hazard. For collimated beams, this warning shall state that viewing the laser output with certain instruments
designed for use at a distance (for example: telescopes and binoculars) may pose an eye hazard.
Wavelength = 1.3/1.5 µm.
Maximum power = 30 mW.
*Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
*IEC is a registered trademark of the International Electrotechnical Commision.
© 2013 EMCORE Corporation | REV 2013.06
626-293-3400
satcom-sales@emcore.com
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising