3 C A I/o
Analog I/O
Specifications
Chapter
3
In This Chapter...
Analog I/O Modules Overview................................................................................... 3–2
Analog I/O Modules................................................................................................... 3–3
Analog Input Modules................................................................................................ 3–5
Analog Output Modules........................................................................................... 3–65
Analog Input/Output Modules.............................................................................. 3–107
2000
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Analog I/O Modules Overview
A variety of analog I/O modules are available for use in local I/O bases.
Each I/O module is identified as an “Input”, “Output”, or “Input/Output” module on its
front panel using the color coding scheme listed below. See Chapter 2 for discrete I/O module
specifications, Chapter 4 for specialty module specifications and Chapter 5 for module wiring
and communications. The following pages contain the analog I/O module specifications.
There are twenty-two analog I/O modules available. The specifications and wiring diagrams,
along with configuration and scaling information are in this chapter.
Use the hardware configuration tool in the Productivity Suite programming software to setup
the I/O modules. See the Productivity Suite help file.
Analog Output Modules
Analog Input Modules
Module Type
(Red: Output)
Module Type
(Blue: Input)

 




 


3–2
Module
Part Number
2000
Analog Input/Output Modules
1
2
3
4
5
6
7
8
18.23
14.23
4.00
4.23
13.56
16.32
8.00
7.54
Module Type
(White: Input/Output)
1I00.00
2I04.00
3I00.00
4I04.00
5I00.00
6I04.00
7I00.00
8I SPARE
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
Analog I/O Modules
Analog Input Modules
Productivity2000 Analog Input Modules
of
Part Number Number
Channels

 




 


Description
See Page
P2-04AD
4
Analog Input (Voltage/Current)
3–5
P2-08AD-1
8
Analog Input (Current)
3–11
P2-08AD-2
8
Analog Input (Voltage)
3–16
P2-08ADL-1*
8
Analog Input (Current)
3–21
P2-08ADL-2*
8
Analog Input (Voltage)
3–25
P2-16AD-1
16
Analog Input (Current)
3–29
P2-16AD-2
16
Analog Input (Voltage)
3–34
P2-16ADL-1*
16
Analog Input (Current)
3–39
P2-16ADL-2*
16
Analog Input (Voltage)
3–43
P2-06RTD
6
Analog RTD Input
3–47
P2-08THM
8
Analog Thermocouple Input
3-54
P2-08NTC
8
Analog Thermistor Input
3–61
* Low resolution analog modules without OLED display.
Analog Output Modules
Productivity2000 Analog Output Modules
Number of
Channels
Description
See Page
P2-04DA
4
Analog Output (Voltage/Current)
3–65
P2-08DA-1
8
Analog Output (Current)
3–71
P2-08DA-2
8
Analog Output (Voltage)
3–76
P2-08DAL-1*
8
Analog Output (Current)
3–81
P2-08DAL-2*
P2-16DA-1
P2-16DA-2
8
Analog Output (Voltage)
3–85
16
Analog Output (Current)
3–89
16
Analog Output (Voltage)
3–94
P2-16DAL-1*
16
Analog Output (Current)
3–99
P2-16DAL-2*
16
Analog Output (Voltage)
3–103
Part Number
1 18.23
2 14.23
3
4.00
4
4.23
5 13.56
6 16.32
7
8.00
8
7.54
* Low resolution analog modules without OLED display.
2000
Hardware User Manual, 1st Edition, Rev. B
3–3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Analog Input/Output Modules
Productivity2000 Analog Input/Output Modules
1I00.00
2I04.00
3I00.00
4I04.00
5I00.00
6I04.00
7I00.00
8I SPARE
3–4
Number of
Channels
Description
See Page
P2-08AD4DA-1
8/4
Analog Input/Output (Current)
3–107
P2-8AD4DA-2
8/4
Analog Input/Output (Voltage)
3–113
Part Number
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-04AD Analog Input
The P2-04AD Voltage/Current Analog Input Module provides four channels for receiving ±10
VDC, ±5 VDC, 0–5 VDC, and 0 to 20mA signals.
C
UL
R
US
Input Specifications
1–9.453V
2 18.23
3 UNDER
4 SPARE
Input Channels
4
Module Signal Input Ranges
±10VDC, ±5VDC, 0–5 VDC, 0–10 VDC, 0–20mA
Signal Resolution
16-bit
Resolution Value of LSB
(least significant bit)
1 LSB = 1 count
±10V = 305μV
±5V = 152μV
Data Range
0–65535 counts unipolar
-32768 to +32767 counts bipolar
Maximum Continuous Overload
±31mA, current input
±100V, voltage input
Input Impedance
1MΩ±10% voltage input
250Ω±0.1% 1/4 W current input
Hardware Filter Characteristics
Low Pass 1st order, -3dB @ 48Hz
Sample Duration Time
2ms per channel (does not include ladder scan time)
All Channel Update Rate
8ms
Open Circuit Detection Time
Zero reading within 1s (current input only)
Conversion Method
Successive approximation
Accuracy vs. Temperature
±10PPM / ºC maximum
Maximum Inaccuracy
0.1% of range voltage, 0.2% of range current
(including temperature drift)
Linearity Error (end to end)
±0.01% of range max., ±10V & ±5V
±0.015% of range max., 0–10V, 0–5V & 0–20mA
Monotonic with no missing codes
Input Stability and Repeatability
±0.035% of range (after 10 min. warmup)
Full Scale Calibration Error
±0.2% of range maximum
Offset Calibration Error
±0.065% of range maximum
Max Crosstalk
-96dB, 1 LSB
Recommended Fuse (external)
Edison S500-32-R, 0.032A fuse
on current inputs only
External DC Power Required
24VDC (-20% / +25%) 35mA
0–5V = 76μV
0–10V = 152μV
0–20mA = 0.305 μA
We recommend using pre-wired ZIPLink cables
and connection modules. See Chapter 5.
If you wish to hand-wire your module, removable
terminal blocks are sold separately. Order part
number P2-RTB or P2-RTB-1
2000
Hardware User Manual, 1st Edition, Rev. B
3–5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-04AD Analog Input (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation
1800VAC applied for 1 second
Insulation Resistance
> 10MΩ @ 500VDC
Heat Dissipation
1.4 W
Enclosure Type
Open Equipment
Module Keying to Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Use ZIPLink Wiring System or removable
terminal block (not included). See “Wiring
Options” in Chapter 5.
EU Directive
See the “EU Directive” topic in the
Productivity Suite Help File. Information
can also be obtained at:
www.productivity2000.com
Connector Type (not included)
18-position removable terminal block
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Removable Terminal Block Specifications*
Part Number
P2-RTB
P2-RTB-1
Number of positions
18 Screw Terminals
18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
Conductors
“USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver Width
1/8 in (3.8 mm) Maximum
Screw Size
M2
N/A
Screw Torque
2.5 lb·in (0.28 N·m)
N/A
*Terminal blocks sold separately.
3–6
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-04AD Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Wiring Diagrams
INTERNAL
MODULE CIRCUITRY
3
CH2 ADC
4
5
CH3 ADC
6
7
CH4 ADC
8
9 10 11 12 13 14 15 16 17 18
+
CH1 ADC
2
-
1
COM
V1+
I1+
V2+
I2+
V3+
I3+
V4+
I4+
COM
COM
COM
24VDC24VDC+
ISOLATED
ANALOG
CIRCUIT
POWER
24 VDC User
Supplied Power
ISOLATED ANALOG
CIRCUIT COMMON
2000
Hardware User Manual, 1st Edition, Rev. B
3–7
Chapter 3: Analog I/O Specifications
Current Sinking Input Circuits
An Edison S500-32-R 0.032A fast-acting
fuse is recommended for all current loops.
V+
–
fuse
I+
.032A
2-Wire 4-20 mA
Transmitter
COM
+
+
2-Wire Transmitter
-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-04AD Analog Input (continued)
Power
Supply
fuse
I+
.032A
+
3-Wire Current +
Transmitter
-
V+
+
Voltage Input Circuits
V+
4-Wire Voltage
Transmitter
AC or DC
Optional Transmitter
Power Supply
4-Wire Transmitter
COM
V+
COM
–
3-Wire Transmitter
24VDC User
Supplied Power
3-Wire Voltage +
Transmitter
V+
4-Wire 4-20 mA
Transmitter
AC or DC
+
fuse
.032A
–
User Supplied
Transmitter Power
4-Wire Transmitter
3–8
COM
2000
I+
COM
3-Wire Transmitter
-
+
24 VDC User
Supplied Power
Notes:
1. Shield connected to signal source common.
2. If current is chosen, I+ MUST be jumpered
to V+. For example, when using 4-20 mA
source for Input 3, I3+ must be connected to
V3+.
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-04AD Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-04AD module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. Select Range
type for each input. If desired, assign a User
Tagname to each input point (channel) selected
and to each Status Bit Item.
2000
Hardware User Manual, 1st Edition, Rev. B
3–9
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-04AD Analog Input (continued)
OLED Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
These screens will
then auto cycle
P2-04AD
Fw. Rev.
1.00
5V, 10V,
+/-5V,
+/-10V,
0-20mA
Channels
Enabled:
4
Hold SEL button down to cycle through primary screens. Release button to select screen.
DISPLAY
SETUP
INFO
This screen will
auto cycle with
status information
End of
Status
Menu
List
DISPLAY
STATUS
INFO
Momentarily Press
SEL button to
toggle through
secondary displays
1
2
3
4
00000
00000
SPARE
00000
DISPLAY
UNITS
HEX
COUNTS
1
2
3
4
DISPLAY
UNITS
+/-V,
mA,V
0000H
0000H
SPARE
0000H
1 0.000V
2 +0.00V
3 SPARE
4 00.00
Error Messages:
An existing error will
be inserted into the
cycling Status Info
screen.
MISSING
EXTERNAL
24VDC
SELFTEST
FAIL
REPLACE
MODULE
Fault Messages – Appear in
place of data during a fault
condition.
3–10
DISPLAY
UNITS
DECIMAL
COUNTS
2000
1
2
3
4
OVER
UNDER
MISSING
CONFIG
DATA
End of
Status
Menu
List
Input signal is OVER the maximum detectable by the module.
Input signal < range minimum. (Voltage only)
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08AD-1 Analog Input
The P2-08AD-1 Current Analog Input Module provides 8 channels for receiving 0 to 20mA
signals.
C

 




 


UL
R
US
Input Specifications
Input Channels
8 sinking
Module Signal Input Range
0–20mA
Signal Resolution
16-bit
Resolution Value of LSB
(least significant bit)
0–20mA = 0.305 μA per count
(1 LSB = 1 count)
Data Range
0 to 65535 counts
Input Type
Single-ended (1 common)
Maximum Continuous Overload
±31mA
Input Impedance
250Ω ±0.1% 1/4 W
Filter Characteristics
Low Pass, -3dB @ 100Hz
Sample Duration Time
9ms per channel
(does not include ladder scan time)
All Channel Update Rate
80ms
Open Circuit Detection Time
Zero reading within 1s
Conversion Method
Successive approximation
Accuracy vs. Temperature
±25PPM / ºC maximum
Maximum Inaccuracy
0.1% of range (including temperature drift)
Linearity Error (end to end)
±0.015% of range
Monotonic with no missing codes
Input Stability and Repeatability
±0.015% of range (after 10 min warmup)
Full Scale Calibration Error
(not including offset)
±0.015% of range maximum
Offset Calibration Error
±0.015% of range maximum
Max Crosstalk
-76dB, ±10 LSB
Recommended Fuse (external)
Edison S500-32-R, 0.032 A fuse
External DC Power Required
24VDC (-20% / +25%) 35mA
We recommend using pre-wired ZIPLink cables
and connection modules. See Chapter 5.
If you wish to hand-wire your module, removable
terminal blocks are sold separately. Order part
number P2-RTB or P2-RTB-1
2000
Hardware User Manual, 1st Edition, Rev. B
3–11
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08AD-1 Analog Input (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation
1800VAC applied for 1 second
Insulation Resistance
> 10MΩ @ 500VDC
Heat Dissipation
800mW
Enclosure Type
Open Equipment
Module Keying to
Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Use ZIPLink Wiring System or removable
terminal block (not included). See “Wiring
Options” in Chapter 5.
EU Directive
See the “EU Directive” topic in the
Productivity Suite Help File. Information
can also be obtained at:
www.productivity2000.com
Connector Type (not
included)
18-position removable terminal block
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
*Meets EMC and Safety requirements. See the D.O.C. for details.
Removable Terminal Block Specifications*
Part Number
P2-RTB
P2-RTB-1
Number of positions
18 Screw Terminals
18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
Conductors
“USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver Width
1/8 in (3.8 mm) Maximum
Screw Size
M2
N/A
Screw Torque
2.5 lb·in (0.28 N·m)
N/A
*Terminal block sold separately.
3–12
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08AD-1 Analog Input (continued)
Wiring Diagrams
Current Input Circuits
An Edison S500-32-R 0.032A fast-acting
fuse is recommended for current loops.
–
fuse
+24VDC User
Supplied Power
+
2-Wire Transmitter
INTERNAL
MODULE CIRCUITRY
fuse
–
CH1 ADC
3
CH2 ADC
4
CH3 ADC
5
CH4 ADC
6
CH5 ADC
7
CH6 ADC
8
CH7 ADC
9 10 11 12 13 14 15 16 17 18
CH8 ADC
+24VDC User
Supplied Power
3-Wire Transmitter
4-Wire 4-20 mA
Transmitter
AC or DC
+
I+
.032A
+ –
+
3-Wire Current
Transmitter
2
+
COM
+
1
-
COM
I1+
I2+
I3+
I4+
I5+
I6+
I7+
I8+
COM
COM
COM
COM
COM
COM
COM
0V
24V+
I+
.032A
+ –
2-Wire 4-20 mA
Transmitter
COM
fuse
.032A
–
I+
COM
User Supplied
Transmitter Power
4-Wire Transmitter
Note: Do not connect both ends of shield.
ISOLATED ANALOG
CIRCUIT POWER
24 VDC User
Supplied Power
ISOLATED ANALOG
CIRCUIT COMMON
2000
Hardware User Manual, 1st Edition, Rev. B
3–13
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08AD-1 Analog Input (continued)
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-08AD-1 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each input point
(channel) selected and to each Status Bit Item.
3–14
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08AD-1 Analog Input (continued)
OLED Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
Hold SEL button down to cycle through primary screens. Release button to select screen.
DISPLAY
SETUP
INFO
DISPLAY
STATUS
INFO
DISPLAY
UNITS
HEX
COUNTS
DISPLAY
UNITS
DECIMAL
COUNTS
DISPLAY
UNITS
MILLIAMP
0-20mA
These screens will
then auto cycle
P2-08AD1
Fw. Rev.
This screen will
auto cycle with
status information
Momentarily Press
SEL button to
toggle through
secondary displays
1.00
16-BIT
0-20mA
7 CH
End of
Status
Menu
List
ENABLED
Error Messages:
An existing error will
be inserted into the
cycling Status Info
screen.
MISSING
EXTERNAL
24VDC
Fault Messages – Appear in
place of data during a fault condition.
2000
0
0
0
0
1
2
3
4
0000H
0000H
0000H
SPARE
1
2
3
4
0.00
0.00
0.00
0.00
5
0
6
0
7
0
8 SPARE
5
6
7
8
0000H
0000H
0000H
SPARE
5
6
7
8
0.00
0.00
0.00
0.00
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
0
0
0
0
0
0
0
SPARE
SELFTEST
FAIL
REPLACE
MODULE
5 OVER
6 UNDER
7
8
0000H
0000H
0000H
0000H
0000H
0000H
0000H
SPARE
MISSING
CONFIG
DATA
1
2
3
4
5
6
7
8
0.00
0.00
0.00
0.00
0.00
0.00
0.00
SPARE
End of
Status
Menu
List
Input current 20mA.
Input current = 0.
Hardware User Manual, 1st Edition, Rev. B
3–15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08AD-2 Voltage Analog Input
The P2-08AD-2 Voltage Analog Input Module provides eight channels for receiving
0–10 VDC signals.
C
UL
R
US
Input Specifications
1
2
3
4
5
6
7
8
1.823V
1.423V
4.000V
9.999V
6.175V
8.320V
7.235V
9.936V
Input Channels
8
Module Signal Input Range
0–10 VDC
Signal Resolution
16-bit
Resolution Value of LSB
(least significant bit)
0–10 VDC = 152μV per count
(1 LSB = 1 count)
Data Range
0 to 65535 counts
Input Type
Single-ended (1 common)
Maximum Continuous Overload
±100V
Input Impedance
250kΩ (typical)
Filter Characteristics
Low Pass, -3dB @ 100Hz
Sample Duration Time
7ms per channel
(does not include ladder scan time)
All Channel Update Rate
80ms
Open Circuit Detection Time
Zero reading within 1s
Conversion Method
Successive approximation
Accuracy vs. Temperature
±25PPM / ºC maximum
Maximum Inaccuracy
0.1% of range (including temperature drift)
Linearity Error (end to end)
±0.015% of range
Monotonic with no missing codes
Input Stability and Repeatability
±0.015% of range (after 10 min warmup)
Full Scale Calibration Error
(not including offset)
±0.015% of range maximum
Offset Calibration Error
±0.015% of range maximum
Max Crosstalk
-76dB, ±10 LSB
External DC Power Required
24VDC (-20% / +25%) 35mA
We recommend using pre-wired ZIPLink cables
and connection modules. See Chapter 5.
If you wish to hand-wire your module, removable
terminal blocks are sold separately. Order part
number P2-RTB or P2-RTB-1
3–16
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08AD-2 Voltage Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation
1800VAC applied for 1 second
Insulation Resistance
> 10MΩ @ 500VDC
Heat Dissipation
82mW
Enclosure Type
Open Equipment
Module Keying to
Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Use ZIPLink Wiring System or removable
terminal block (not included). See “Wiring
Options” in Chapter 5.
EU Directive
See the “EU Directive” topic in the
Productivity Suite Help File. Information
can also be obtained at:
www.productivity2000.com
Connector Type (not
included)
18-position removable terminal block
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Removable Terminal Block Specifications*
Part Number
P2-RTB
P2-RTB-1
Number of
positions
18 Screw Terminals
18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
Conductors
“USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver Width
1/8 in (3.8 mm) Maximum
Screw Size
M2
N/A
Screw Torque
2.5 lb in (0.28 N·m)
N/A
*Terminal block sold separately.
2000
Hardware User Manual, 1st Edition, Rev. B
3–17
Chapter 3: Analog I/O Specifications
Wiring Diagrams
INTERNAL
MODULE CIRCUITRY
CH1 ADC
3
CH2 ADC
4
CH3 ADC
5
CH4 ADC
6
CH5 ADC
7
CH6 ADC
8
CH7 ADC
9 10 11 12 13 14 15 16 17 18
+
2
-
COM
V1+
V2+
V3+
V4+
V5+
V6+
V7+
V8+
COM
COM
COM
COM
COM
COM
COM
0V
24V+
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08AD-2 Voltage Analog Input (continued)
CH8 ADC
Voltage Input Circuits
V+
4-Wire Voltage
Transmitter
AC or DC
Transmitter
Power Supply
4-Wire Transmitter
V+
+
3-Wire Voltage +
Transmitter
–
3-Wire Transmitter
ISOLATED ANALOG
CIRCUIT POWER
24 VDC User
Supplied Power
Note: For maximum
accuracy jumper unused
inputs to common.
ISOLATED ANALOG
CIRCUIT COMMON
3–18
COM
2000
Hardware User Manual, 1st Edition, Rev. B
COM
-
+
24 VDC User
Supplied Power
V7+
V8+
COM
Chapter 3: Analog I/O Specifications
P2-08AD-2 Voltage Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-08AD-2 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each input point
(channel) selected and to each Status Bit Item.
2000
Hardware User Manual, 1st Edition, Rev. B
3–19
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08AD-2 Voltgage Analog Input (continued)
OLED Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
Hold SEL button down to cycle through primary screens. Release button to select screen.
DISPLAY
SETUP
INFO
DISPLAY
STATUS
INFO
DISPLAY
UNITS
HEX
COUNTS
DISPLAY
UNITS
DECIMAL
COUNTS
DISPLAY
UNITS
VOLTS
0-10VDC
These screens will
then auto cycle
P2-08AD2
Fw. Rev.
1.00
16-BIT
0-10V
7 CH
ENABLED
This screen will
auto cycle with
status information
Momentarily Press
SEL button to
toggle through
secondary displays
End of
Status
Menu
List
Error Messages:
An existing error will
be inserted into the
cycling Status Info
screen.
MISSING
EXTERNAL
24VDC
2000
0
0
0
0
1
2
3
4
0000H
0000H
0000H
0000H
1
2
3
4
0.00V
0.00V
0.00V
0.00V
5
0
6
0
7
0
8 SPARE
5
6
7
8
0000H
0000H
0000H
SPARE
5
6
7
8
0.00V
0.00V
0.00V
SPARE
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
0000H
0000H
0000H
0000H
0000H
0000H
0000H
SPARE
1
2
3
4
5
6
7
8
0.00V
0.00V
0.00V
0.00V
0.00V
0.00V
0.00V
SPARE
0
0
0
0
0
0
0
SPARE
SELFTEST
FAIL
REPLACE
MISSING
CONFIG
DATA
MODULE
Fault Messages – Appear in
place of data during a fault condition.
3–20
1
2
3
4
5 OVER
6 UNDER
7
8
Input voltage 10V.
Input voltage = 0.
Hardware User Manual, 1st Edition, Rev. B
End of
Status
Menu
List
Chapter 3: Analog I/O Specifications
P2-08ADL-1 Current Analog Input
The P2-08ADL-1 Low Resolution Current Analog Input Module provides eight channels for
receiving 0–20 mA signals for use with Productivity2000 system.
C
UL
R
US
Input Specifications
Input Channels
8 sinking
Module Signal Input Range
0–20mA
Signal Resolution
13-bit
Resolution Value of LSB
(least significant bit)
0–20mA = 2.44 μA per count
(1LSB = 1 count)
Data Range
0–8191 counts
Input Type
Single-ended (1 common)
Maximum Continuous
Overload
±31mA
Input Impedance
124Ω, ±0.5%, 1/2W Current Input
Filter Characteristics
Low Pass, -3dB @ 120Hz
Sample Duration Time
2ms per channel
(does not include ladder scan time)
All Channel Update Rate
20ms
Open Circuit Detection Time
Zero reading within 100ms
Conversion Method
Successive approximation
Accuracy vs. Temperature
±75PPM / ºC maximum
Maximum Inaccuracy
0.5% of range
(including temperature drift)
Linearity Error (end to end)
±0.0037% of range
Monotonic with no missing codes
Input Stability and
Repeatability
Full Scale Calibration Error
(including offset)
Offset Calibration Error
Max Crosstalk at DC, 50Hz
and 60Hz
Recommended Fuse
(external)
External DC Power Required
±0.024% of range
±0.098% of range
±0.098% of range
4 counts / 0.048% of range
Edison S500-32-R, 0.032 A fuse
24VDC (-20% / + 25%), 30mA
We recommend using pre-wired ZIPLink cables
and connection modules. See Chapter 5.
If you wish to hand-wire your module, removable
terminal blocks are sold separately. Order part
number P2-RTB or P2-RTB-1
2000
Hardware User Manual, 1st Edition, Rev. B
3–21
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08ADL-1 Current Analog Input (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation
1800VAC applied for 1 second
Insulation Resistance
>10MΩ @ 500VDC
Heat Dissipation
1200mW
Enclosure Type
Open Equipment
Module Keying to
Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Use ZIPLink Wiring System or removable
terminal block (not included). See “Wiring
Options” in Chapter 5.
See the “EU Directive” topic in the
Productivity Suite Help File. Information
can also be obtained at:
www.productivity2000.com
Field Wiring
EU Directive
Terminal Type
18-position Removable Terminal Block
Weight
100g (3.5 oz)
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Agency Approvals
Removable Terminal Block Specifications*
Part Number
P2-RTB
P2-RTB-1
Number of
positions
18 Screw Terminals
18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in (6– 7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
Conductors
“USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver Width
1/8 in (3.8 mm) Maximum
Screw Size
M2
N/A
Screw Torque
2.5 lb in (0.28 N·m)
N/A
*Terminal block sold separately.
3–22
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08ADL-1 Current Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Wiring Diagrams
INTERNAL
MODULE CIRCUITRY
-
COM
I1+
I2+
I3+
I4+
I5+
I6+
I7+
I8+
COM
COM
COM
COM
COM
COM
COM
24VDC+ 24VDC+
Current Input Circuits
An Edison S500-32-R 0.032A fast-acting
fuse is recommended for current loops.
124Ω
CH1 ADC
124Ω
CH2 ADC
124Ω
CH3 ADC
124Ω
CH4 ADC
124Ω
CH5 ADC
124Ω
CH6 ADC
124Ω
CH7 ADC
124Ω
CH8 ADC
–
fuse
+24VDC User
Supplied Power
+
2-Wire Transmitter
COM
fuse
+
+
3-Wire Current
Transmitter
–
+
AC or DC
+
I+
.032A
–
+24VDC User
Supplied Power
3-Wire Transmitter
4-Wire 4-20 mA
Transmitter
I+
.032A
+ –
2-Wire 4-20 mA
Transmitter
COM
fuse
.032A
–
I+
COM
User Supplied
Transmitter Power
4-Wire Transmitter
Note: Do not connect both ends of shield.
ISOLATED ANALOG
CIRCUIT POWER
24 VDC User
Supplied Power
ISOLATED ANALOG
CIRCUIT COMMON
2000
Hardware User Manual, 1st Edition, Rev. B
3–23
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
c
D
P2-08ADL-1 Current Analog Input (continued)
Module Configuration
Using the Hardware Configuration tool in the Productivity
Suite programming software, drag and drop the
P2-08ADL-1 module into the base configuration.
Select Automatic Module Verification or No Verification and
Enable Hot Swap. If desired, assign a User Tagname to
each input point (channel) selected and to each Status Bit
Item.
3–24
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08ADL-2 Voltage Analog Input
The P2-08ADL-2 Low Resolution Voltage Analog Input Module provides eight channels for
receiving 0–10 VDC signals.
C
UL
R
Input Specifications
US
Input Channels
8
Module Signal Input Range
0–10 VDC
Resolution
13-bit
Data Range
0–8191 counts
Input Type
Single-ended (1 common)
Resolution Value of LSB
0–10 VDC = 1.22 mV per count
(1 LSB = 1 Count)
Maximum Continuous
Overload
±100VDC
Input Impedance
>150kΩ
Filter Characteristics
Low Pass, -3dB @ 500Hz
Sample Duration Time
6.25 ms,
(does not include ladder scan time)
All Channel Update Rate
25ms
Open Circuit Detection Time
Zero reading within 100ms
Conversion Method
Successive approximation
Accuracy vs. Temperature
±75PPM / ºC maximum
Maximum Inaccuracy
0.5% of range
(including temperature drift)
±3 count maximum
Monotonic with no missing codes
Linearity Error (end to end)
Input Stability and
Repeatability
Full Scale Calibration Error
(including offset)
Offset Calibration Error
Max Crosstalk at DC,
50/60Hz
External 24VDC Power
Required
±0.024% of range
±0.097% of range
±0.097% of range
4 counts / 0.048% of range
24VDC (-20% / +25%), 30mA
We recommend using pre-wired ZIPLink cables
and connection modules. See Chapter 5.
If you wish to hand-wire your module, removable
terminal blocks are sold separately. Order part
number P2-RTB or P2-RTB-1
2000
Hardware User Manual, 1st Edition, Rev. B
3–25
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08ADL-2 Voltage Analog Input (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation
1800VAC applied for 1 second
Insulation Resistance
>10MΩ @ 500VDC
Heat Dissipation
1200mW
Enclosure Type
Open Equipment
Module Keying to
Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Use ZIPLink Wiring System or removable
terminal block (not included). See “Wiring
Options” in Chapter 5.
See the “EU Directive” topic in the
Productivity Suite Help File. Information
can also be obtained at:
www.productivity2000.com
Field Wiring
EU Directive
Terminal Type
18-position Removable Terminal Block
Weight
100g (3.5 oz)
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Agency Approvals
Removable Terminal Block Specifications*
Part Number
P2-RTB
P2-RTB-1
Number of positions
18 Screw Terminals
18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
Conductors
“USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver Width
1/8 in (3.8 mm) Maximum
Screw Size
M2
N/A
Screw Torque
2.5 lb·in (0.28 N·m)
N/A
*Terminal block sold separately.
3–26
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08ADL-2 Voltage Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Wiring Diagrams
INTERNAL
MODULE CIRCUITRY
Voltage Input Circuits
2
CH1 ADC
3
CH2 ADC
4
CH3 ADC
5
CH4 ADC
6
CH5 ADC
7
CH6 ADC
8
CH7 ADC
9 10 11 12 13 14 15 16 17 18
+
1
-
COM
V1+
V2+
V3+
V4+
V5+
V6+
V7+
V8+
COM
COM
COM
COM
COM
COM
COM
0V
24V+
CH8 ADC
V+
4-Wire Voltage
Transmitter
AC or DC
COM
Transmitter
Power Supply
4-Wire Transmitter
V+
+
3-Wire Voltage +
Transmitter
_
3-Wire Transmitter
COM
-
+
24 VDC User
Supplied Power
V7+
V8+
COM
ISOLATED ANALOG
Note:
For
maximum
accuracy
jumper
CIRCUIT POWER
unsused inputs to common.
24 VDC User
Supplied Power
ISOLATED ANALOG
CIRCUIT COMMON
2000
Hardware User Manual, 1st Edition, Rev. B
3–27
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08ADL-2 Voltage Analog Input (continued)
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-08ADL-2 module into the
base configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each input point
(channel) selected and to each Status Bit Item.
8CH, 13-BIT, VOLTAGE, ANALOG INPUT
3–28
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16AD-1 Current Analog Input
The P2-16AD-1 Current Analog Input Module provides sixteen channels for receiving
0–20mA input signals.
C
1
2
3
4
5
6
7
8
UL
R
US
Input Specifications
14.54 M
A
03.23 M
A
7.23 M
A
UNDER
M
3.23 A
OVER
2.32 M
A
SPARE
Input Channels
16 sinking
Module Signal Input Range
0–20mA
Signal Resolution
16-bit
Resolution Value of LSB
(least significant bit)
0–20 mA = 305μA per count
(1 LSB = 1 count)
Data Range
0 to 65535 counts
Input Type
Single-ended (1 common)
Maximum Continuous Overload
±31mA
Input Impedance
250Ω ±0.1% 1/4W
Filter Characteristics
Low Pass, -3dB @ 100Hz
Sample Duration Time
4ms per channel
(does not include ladder scan time)
All Channel Update Rate
112ms
Open Circuit Detection Time
Zero reading within 1s
Conversion Method
Successive approximation
Accuracy vs. Temperature
±25PPM / ºC maximum
Maximum Inaccuracy
0.1% of range
(including temperature drift)
Linearity Error (end to end)
±10 LSB maximum (±0.015% of range)
Monotonic with no missing codes
Input Stability and Repeatability
±0.015% of range (after 10 min warmup)
Full Scale Calibration Error
(not including offset)
±10 LSB
Offset Calibration Error
±10 LSB maximum (±0.015% of range)
Max Crosstalk
-76dB, ±10 LSB
Recommended Fuse (external)
Edison S500-32-R, 0.032 A fuse
External DC Power Required
24VDC (-20% / +25%) 35mA
*Meets EMC and Safety requirements. See the Declaration of Conformity for details.
We recommend using pre-wired ZIPLink cables and
connection modules. See Chapter 5.
Module connector type is a 24-pin Molex Style
43025-2400.
2000
Hardware User Manual, 1st Edition, Rev. B
3–29
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16AD-1 Current Analog Input (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation
1800VAC applied for 1 second
Insulation Resistance
> 10MΩ @ 500VDC
Heat Dissipation
800mW
Enclosure Type
Open Equipment
Module Keying to
Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
ZIPLink Wiring System ONLY. See “Wiring
Options” in Chapter 5. Must use copper
conductors 75ºC or equivalent.
EU Directive
See the “EU Directive” topic in the
Productivity Suite Help File. Information
can also be obtained at:
www.productivity2000.com
Connector Type
24-Pin Molex Style 43025-2400
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
Connector Specifications
3–30
Connector Type
24-Pin Molex Style 43025-2400
Number of Pins
24
Pin Spacing
3x3 mm (0.118 x 0.118 in)
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16AD-1 Current Analog Input (continued)
Wiring Diagrams
INTERNAL
MODULE
CIRCUITRY
COM
COM
COM
COM
I1+
I5+
I2+
I6+
I3+
I7+
I4+
I8+
+V
+V
-V
-V
I9+
I13+
I10+
I14+
I11+
I15+
I12+
I16+
ZL-RTB20
Labels
+
13
1
14
2
15
3
16
4
17
5
18
6
19
7
20
8
21
9
22
10
23
11
24
12
CH1 ADC
CH5 ADC
CH2 ADC
CH6 ADC
CH3 ADC
CH7 ADC
CH4 ADC
CH8 ADC
CH9 ADC
CH13 ADC ISOLATED
CH10 ADC ANALOG
CH14 ADC CIRCUIT
CH11 ADC
POWER
CH15 ADC
CH12
ADC
Current
Input Circuits
CH16 ADC
An Edison
S500-32-R 0.032A fast-acting
fuse is recommended for current loops.
–
fuse
2-Wire 4-20 mA
Transmitter
ISOLATED ANALOG
+
CIRCUIT COMMON
+24VDC User
Supplied Power
2-Wire Transmitter
–
fuse
2-Wire Transmitter
COM
fuse
+
+
3-Wire Current
Transmitter
–
–
AC or DC
+
COM
fuse
.032A
–
I+
COM
User Supplied
Transmitter Power
4-Wire Transmitter
+24VDC User
Supplied Power
3-Wire Transmitter
+
I+
.032A
+ –
4-Wire 4-20 mA
Transmitter
I+
+24VDC User
Supplied Power
3-Wire Transmitter
+24VDC User
Supplied Power
+
4-Wire 4-20 mA
Transmitter
I+
.032A
+ –
2-Wire 4-20 mA
Transmitter
fuse
.032A
+ –
+
3-Wire Current
Transmitter
An Edison S500-32-R 0.032A fast-acting
fuse is recommended for current loops.
–
COM
+
Current Input Circuits
I+
.032A
+ –
Note: Do not connect both ends of shield.
COM
fuse
.032A
2000
I+
Hardware User Manual, 1st Edition, Rev. B
COM
3–31
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16AD-1 Current Analog Input (continued)
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-16AD-1 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each input point
(channel) selected and to each Status Bit Item.
3–32
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16AD-1 Current Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
OLED Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
Hold SEL button down to cycle through primary screens. Release button to select screen.
DISPLAY
SETUP
INFO
DISPLAY
UNITS
HEX
COUNTS
DISPLAY
UNITS
DECIMAL
COUNTS
DISPLAY
STATUS
INFO
DISPLAY
UNITS
MILLIAMP
0-20mA
These screens will
then auto cycle
P2-16AD1
Fw. Rev.
1.00
16-BIT
0-20mA
15 CH
ENABLED
This screen will
auto cycle with
status information
Momentarily Press
SEL button to
toggle through
secondary displays
End of
Status
Menu
List
Error Messages – An existing error will be
inserted into the cycling Status Info screen.
MISSING
EXTERNAL
24VDC
SELFTEST
FAIL
REPLACE
MODULE
End of
Status
Menu
List
MISSING
CONFIG
DATA
1
2
3
4
0
0
0
0
1
2
3
4
0000H
0000H
0000H
0000H
1
2
3
4
0.00
0.00
0.00
0.00
5
6
7
8
0
0
0
0
5
6
7
8
0000H
0000H
0000H
0000H
5
6
7
8
0.00
0.00
0.00
0.00
9
10
11
12
0
0
0
0
9
10
11
12
0000H
0000H
0000H
0000H
9
10
11
12
0.00
0.00
0.00
0.00
13
0
14
0
15
0
16 SPARE
13
14
15
16
0000H
0000H
0000H
SPARE
13
14
15
16
0.00
0.00
0.00
SPARE
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
0000H
0000H
0000H
0000H
0000H
0000H
0000H
0000H
1
2
3
4
5
6
7
8
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
9
10
11
12
13
14
15
16
0000H
0000H
0000H
0000H
0000H
0000H
0000H
SPARE
9
10
11
12
13
14
15
16
0.00
0.00
0.00
0.00
0.00
0.00
0.00
SPARE
9
10
11
12
13
14
15
16
Fault Messages – Appear in
place of data during a fault condition.
2000
5
6
7
8
OVER
UNDER
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SPARE
Input current 20mA.
Input current = 0.
Note:
SPARE
denotes
deselected
channel.
Hardware User Manual, 1st Edition, Rev. B
3–33
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16AD-2 Voltage Analog Input
The P2-16AD-2 Voltage Analog Input Module provides sixteen channels for receiving 0 to
10 VDC signals.
C
1
2
3
4
5
6
7
8
UL
R
Input Specifications
US
1.823V
1.423V
4.000V
9.999V
6.175V
8.320V
7.225V
9.936V
Input Channels
16
Module Signal Input Range
0–10 VDC
Signal Resolution
16-bit
Resolution Value of LSB
(least significant bit)
0–10 VDC = 152μV per count
(1 LSB = 1 count)
Data Range
0 to 65535 counts
Input Type
Single-ended (1 common)
Maximum Continuous
Overload
±100V
Input Impedance
250kΩ (typical)
Filter Characteristics
Low Pass, -3dB @ 100Hz
Sample Duration Time
4ms per channel
(does not include ladder scan time)
All Channel Update Rate
112ms
Open Circuit Detection Time
Zero reading within 1s
Conversion Method
Successive approximation
Accuracy vs. Temperature
±25PPM / ºC maximum
Maximum Inaccuracy
0.1% of range
(including temperature drift)
Linearity Error (end to end)
±10 LSB maximum (±0.015% of range)
Monotonic with no missing codes
Input Stability and
Repeatability
Full Scale Calibration Error
(not including offset)
±10 LSB
±10 LSB maximum (±0.015% of range)
Offset Calibration Error
±10 LSB maximum
Max Crosstalk
-76dB, ±10 LSB
External DC Power Required
24VDC (-20% / +25%) 35mA
We recommend using pre-wired ZIPLink cables and
connection modules. See Chapter 5.
Module connector type is a 24-pin Molex Style
43025-2400.
3–34
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16AD-2 Voltage Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation
1800VAC applied for 1 second
Insulation Resistance
> 10MΩ @ 500VDC
Heat Dissipation
59mW
Enclosure Type
Open Equipment
Module Keying to
Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
ZIPLink Wiring System ONLY. See “Wiring
Options” in Chapter 5. Must use copper
conductors 75ºC or equivalent.
EU Directive
See the “EU Directive” topic in the Productivity
Suite Help File. Information can also be
obtained at: www.productivity2000.com
Connector Type
24-Pin Molex Style 43025-2400
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the Declaration of Conformity for details.
Connector Specifications
Connector Type
24-Pin Molex Style 43025-2400
Number of Pins
24
Pin Spacing
3 x 3 mm (0.118 x 0.118 in)
2000
Hardware User Manual, 1st Edition, Rev. B
3–35
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16AD-2 Voltage Analog Input (continued)
Wiring Diagrams
INTERNAL
MODULE
CIRCUITRY
COM
COM
COM
COM
V1+
V5+
V2+
V6+
V3+
V7+
V4+
V8+
+V
24VDC+/-10% +V
-V
-V
V9+
V13+
V10+
V14+
V11+
V15+
V12+
ZL-RTB20
V16+
Labels
+
13
1
14
2
15
3
16
4
17
5
18
6
19
7
20
8
21
9
22
10
23
11
24
12
CH1 ADC
CH5 ADC
CH2 ADC
CH6 ADC
CH3 ADC
CH7 ADC
CH4 ADC
CH8 ADC
CH9 ADC
CH13 ADC
CH10 ADC
CH14 ADC
CH11 ADC
CH15 ADC
CH12 ADC
CH16 ADC
ISOLATED
ANALOG
CIRCUIT
POWER
Voltage Input Circuits
V+
4-Wire Voltage
Transmitter
COM
ISOLATED ANALOG
CIRCUIT COMMON
AC or DC
4-Wire Transmitter
Voltage Input Circuits
V+
4-Wire Voltage
Transmitter
AC or DC
COM
4-Wire Transmitter
3-Wire Transmitter
V+
–
3-Wire Transmitter
3–36
-
+
24 VDC User
Supplied Power
2000
COM
3-Wire Voltage +
Transmitter
–
Note: For+maximum accuracy jumperCOM
unused
inputs+ to common.
3-Wire Voltage
V+
+
Transmitter
Power Supply
Transmitter
Transmitter
Power Supply
-
+
24 VDC User
Supplied Power
V15+
V16+
COM
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16AD-2 Voltage Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-16DA-2 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each output point
(channel) selected and to each Status Bit Item.
2000
Hardware User Manual, 1st Edition, Rev. B
3–37
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16AD-2 Voltage Analog Input (continued)
OLED Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
Hold SEL button down to cycle through primary screens. Release button to select screen.
DISPLAY
SETUP
INFO
DISPLAY
STATUS
INFO
DISPLAY
UNITS
HEX
COUNTS
DISPLAY
UNITS
DECIMAL
COUNTS
DISPLAY
UNITS
VOLTS
+/-10VDC
These screens will
then auto cycle
P2-16DA2
Fw. Rev.
1.00
16-BIT
0-10VDC
15 CH
ENABLED
This screen will
auto cycle with
status information
End of
Status
Menu
List
Error Messages – An existing error will be
inserted into the cycling Status Info screen.
MISSING
EXTERNAL
24VDC
End of
Status
Menu
List
3–38
Momentarily Press
SEL button to
toggle through
secondary displays
2000
SELFTEST
FAIL
REPLACE
MODULE
MISSING
CONFIG
DATA
1
2
3
4
0
0
0
0
1
2
3
4
0000H
0000H
0000H
0000H
1+0.000V
2+0.000V
3+0.000V
4+0.000V
5
6
7
8
0
0
0
0
5
6
7
8
0000H
0000H
0000H
0000H
5+0.000V
6+0.000V
7+0.000V
8+0.000V
9
10
11
12
0
0
0
0
9
10
11
12
0000H
0000H
0000H
0000H
9+0.000V
10+0.00V
11+0.00V
12+0.00V
13
14
15
16
0
0
0
0
13
14
15
16
0000H
0000H
0000H
0000H
13+0.00V
14+0.00V
15+0.00V
16+0.00V
1
2
3
4
5
6
7
8
0
0
0
0
0
0
0
0
1
2
3
4
5
6
7
8
0000H
0000H
0000H
0000H
0000H
0000H
0000H
0000H
1+0.000V
2+0.000V
3+0.000V
4+0.000V
5+0.000V
6+0.000V
7+0.000V
8+0.000V
9
10
11
12
13
14
15
16
0
0
0
0
0
0
0
0
9
10
11
12
13
14
15
16
0000H
0000H
0000H
0000H
0000H
0000H
0000H
0000H
9+0.000V
10+0.00V
11+0.00V
12+0.00V
13+0.00V
14+0.00V
15+0.00V
16+0.00V
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16ADL-1 Current Analog Input
The P2-16ADL-1 Low Resolution Current Analog Input Module provides sixteen channels
for receiving 0–20 mA signals.
C
UL
R
US
Input Specifications
Input Channels
Module Signal Input Range
Signal Resolution
Resolution Value of LSB
(least significant bit)
Data Range
Input Type
Maximum Continuous Overload
Input Impedance
Filter Characteristics
Sample Duration Time
All Channel Update Rate
Open Circuit Detection Time
Conversion Method
Accuracy vs. Temperature
Maximum Inaccuracy
Linearity Error (end to end)
Input Stability and Repeatability
Full Scale Calibration Error
(including offset)
Offset Calibration Error
Max Crosstalk at DC, 50Hz and
60Hz
Recommended Fuse (external)
External DC Power Required
16 sinking
0–20mA
13-bit
0–20mA = 2.44 μA per count
( 1 LSB = 1 count)
0–8191 counts
Single-ended (1 common)
±44mA
124Ω, ±0.5% 1/2W Current Input
Low Pass, -3dB @ 120Hz
2ms per channel
(does not include ladder scan time)
25ms
Zero reading within 100ms
Successive approximation
±75PPM / ºC maximum
0.5% of range
(including temperature changes)
±0.036% count maximum
Monotonic with no missing codes
±0.024% of range
±0.097% of range
±0.097% of range
4 counts / 0.048% of range
Edison S500-32-R, 0.032 A fuse
24VDC (-20% / +25%) @ 35mA
We recommend using pre-wired ZIPLink cables and
connection modules. See Chapter 5.
Module connector type is a 24-pin Molex Style
43025-2400.
2000
Hardware User Manual, 1st Edition, Rev. B
3–39
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16ADL-1 Current Analog Input (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation
1800VAC applied for 1 second
Insulation Resistance
>10MΩ @ 500VDC
Heat Dissipation
1100mW maximum
Enclosure Type
Open Equipment
Module Keying to Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000
System
Field Wiring
Use ZIPLink Wiring System ONLY.
See “Wiring Options” in Chapter 5.
Must use copper conductors 75°C or
equivalent.
EU Directive
See the “EU Directive” topic in
the Productivity Suite Help File.
Information can also be obtained at:
www.productivity2000.com
Terminal Type
24-Pin Molex Style 43025-2400
Weight
100g (3.5 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Connector Specifications
3–40
Connector Type
24-Pin Molex Style 43025-2400
Number of Pins
24
Pin Spacing
3x3 mm (0.118 x 0.118 in)
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16ADL-1 Current Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Wiring Diagrams
INTERNAL
MODULE
CIRCUITRY
COM
COM
COM
COM
I1+
I5+
I2+
I6+
I3+
I7+
I4+
I8+
+V
+V
-V
-V
I9+
I13+
I10+
I14+
I11+
I15+
I12+
I16+
ZL-RTB20
Labels
+
13
1
14
2
15
3
16
4
17
5
18
6
19
7
20
8
21
9
22
10
23
11
24
12
CH1 ADC
CH5 ADC
CH2 ADC
CH6 ADC
CH3 ADC
CH7 ADC
CH4 ADC
CH8 ADC
CH9 ADC
CH13 ADC ISOLATED
CH10 ADC ANALOG
Current
Circuits
CH14 ADCInput
CIRCUIT
CH11
ADC
An Edison
S500-32-R
0.032AR
fast-acting
POWE
CH15 ADC
fuse is recommended
for current loops.
CH12 ADC
– ADC
CH16
fuse
+24VDC User
Supplied Power
+
ISOLATED ANALOG
2-Wire Transmitter
CIRCUIT COMMON
–
fuse
2-Wire Transmitter
COM
fuse
+
+
3-Wire Current
Transmitter
–
–
+24VDC User
Supplied Power
4-Wire 4-20 mA
Transmitter
AC or DC
+
COM
fuse
.032A
–
I+
COM
User Supplied
Transmitter Power
4-Wire Transmitter
+24VDC User
Supplied Power
3-Wire Transmitter
+
I+
.032A
+ –
I+
3-Wire Transmitter
+24VDC User
Supplied Power
+
4-Wire 4-20 mA
Transmitter
I+
.032A
+ –
2-Wire 4-20 mA
Transmitter
fuse
.032A
+ –
+
3-Wire Current
Transmitter
An Edison S500-32-R 0.032A fast-acting
fuse is recommended for current loops.
–
COM
+
Current Input Circuits
I+
.032A
+ –
2-Wire 4-20 mA
Transmitter
Note: Do not connect both ends of shield.
COM
fuse
.032A
2000
I+
COM
Hardware User Manual, 1st Edition, Rev. B
3–41
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16ADL-1 Current Analog Input (continued)
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-16ADL-1 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each input point
(channel) selected and to each Status Bit Item.
13
3–42
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16ADL-2 Voltage Analog Input
The P2-16ADL-2 Low Resolution Voltage Analog Input Module provides sixteen channels for
receiving 0–10 VDC signals.
C
UL
R
US
Input Specifications
Input Channels
16
Module Signal Input Range
0–10 VDC
Signal Resolution
13-bit
Resolution of LSB
(least significant bit)
0–10 VDC = 1.22 mV per count
(1LSB = 1 count)
Data Range
0–8191 counts
Input Type
Single-ended (1 common)
Maximum Continuous
Overload
±100VDC
Input Impedance
>150kΩ
Filter Characteristics
Low Pass, -3dB @ 500Hz
Sample Duration Time
6.25ms per channel
(does not include ladder scan time)
All Channel Update Rate
25ms
Open Circuit Detection Time
Zero reading within 100ms
Accuracy vs. Temperature
±75PPM / ºC maximum
Conversion Method
Successive approximation
Maximum Inaccuracy
0.5% of range
(including temperature drift)
±0.036% count maximum
Monotonic with no missing codes
Linearity Error (end to end)
Input Stability and
Repeatability
Full Scale Calibration Error
(including offset)
±0.024% of range
±0.097% of range
Offset Calibration Error
±0.097% of range
Max Crosstalk
4 counts / 0.048% of range
External 24VDC Power
Required
24VDC (-20% / +25%), 35mA
We recommend using pre-wired ZIPLink cables and
connection modules. See Chapter 5.
Module connector type is a 24-pin Molex Style
43025-2400.
2000
Hardware User Manual, 1st Edition, Rev. B
3–43
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16ADL-2 Voltage Analog Input (continued)
General Specifications
Surrounding Air
Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation
1800VAC applied for 1 second
Insulation Resistance
>10MΩ @ 500VDC
Heat Dissipation
1100mW max
Enclosure Type
Open Equipment
Module Keying to
Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
EU Directive
ZIPLink Wiring System ONLY. See “Wiring
Options” in Chapter 5. Must use copper
conductors 75ºC or equivalent.
See the “EU Directive” topic in the
Productivity2000 Help File. Information
can also be obtained at:
www.productivity2000.com
Terminal Type
24-Pin Molex Style 43025-2400
Weight
102g (3.6 oz)
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Agency Approvals
Connector Specifications
3–44
Connector Type
24-Pin Molex Style 43025-2400
Number of Pins
24
Pin Spacing
3 x 3 mm (0.118 x 0.118 in)
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16ADL-2 Voltage Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Wiring Diagrams
INTERNAL
MODULE
CIRCUITRY
24VDC +/-10%
ZL-RTB20
Labels
COM
COM
COM
COM
V1+
V5+
V2+
V6+
V3+
V7+
V4+
V8+
+V
+V
-V
-V
V9+
V13+
V10+
V14+
V11+
V15+
V12+
V16+
+
13
1
14
2
15
3
16
4
17
5
18
6
19
7
20
8
21
9
22
10
23
11
24
12
CH1 ADC
CH5 ADC
CH2 ADC
CH6 ADC
CH3 ADC
CH7 ADC
CH4 ADC
CH8 ADC
CH9 ADC
CH13 ADC ISOLATED
CH10 ADC ANALOG
CH14 ADC
CIRCUIT
CH11 ADC
POWE R
CH15 ADC
CH12 ADC
CH16
ADC
Voltage
Input Circuits
V+
4-Wire Voltage
Transmitter
COM
ISOLATED ANALOG
CIRCUIT
COMMON
Transmitter
AC or
DC
Power Supply
4-Wire Transmitter
Voltage Input Circuits
V+
4-Wire Voltage
Transmitter
AC or DC
COM
3-Wire Voltage +
Transmitter
Transmitter
Power Supply
–
3-Wire Transmitter
4-Wire Transmitter
+
3-Wire Voltage +
Transmitter
V+
Note: For maximum accuracy jumper
COM
unused inputs to common.
–
3-Wire Transmitter
-
+
V+
+
COM
-
+
24 VDC User
Supplied Power
V15+
V16+
COM
24 VDC User
Supplied Power
2000
Hardware User Manual, 1st Edition, Rev. B
3–45
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16ADL-2 Voltage Analog Input (continued)
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-16ADL-2 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each input point
(channel) selected and to each Status Bit Item.
13
3–46
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-06RTD Analog Input
The P2-06RTD input module provides six differential channels for receiving RTD and
resistance input signals.
C
UL
R
US
1
OVER
2
0526
3
1000 °F
4
UNDER
5
OVER
6 21.35 M
V
RTD Input Specifications
Input Channels
Max. Common Mode
Voltage
Data Format
6 Differential
Common Mode Rejection
Absolute Maximum
Ratings
Internal Resolution
-90dB min. @ DC, -150dB min. @ 50/60 Hz
Floating Point
Fault protected input, ±50V
16-bit, ±0.1°C or °F (up to 100Hz filter)
Pt100
Pt1000
JPt100
10Ω Cu.
25Ω Cu.
120Ω Ni.
Input Ranges
(RTD Types)
Terminal Block Included. Not
Compatible with ZIPLink.
Warranty: Thirty-day moneyback guarantee. Two-year
limited replacement. (See www.
productivity2000.com for details).
5VDC
-200°C/850°C (-328°F/1562°F)
-200°C/595°C (-328°F/1103°F)
-100°C/450°C (-148°F/842°F)
-200°C/260°C (-328°F/500°F)
-200°C/260°C (-328°F/500°F)
-80°C/260°C (-112°F/500°F)
RTD Linearization
Excitation Current (all
ranges)
Accuracy vs. Temperature
Automatic
Full Scale Calibration
±1°C
Offset Calibration Error
±1 count (negligible)
Linearity Error (end to end)
±0.5°C maximum, ±0.01°C typical,
Monotonic with no missing codes
Maximum Inaccuracy
±1°C maximum (excluding RTD error)
(including temperature drift)
Warm-up Time
2 minutes for ±0.2% repeatability
Sample Duration
(Single channel update
rate)
Dependent on digital Filter Settings –
488ms @ 10Hz, 88ms @ 50Hz, 75ms @ 60Hz,
56ms @ 100Hz, 48ms @ 250Hz
Filter Characteristics
Digital filter cutoff frequencies:
10Hz, 50Hz, 60Hz, 100Hz, or 250Hz
All Channel Update Rate
Single channel update rate times the
number of enabled channels
Open Circuit Detection
Time
Conversion Method
External DC Power
Required
2000
200μA
±5PPM per °C (maximum)
Positive full scale reading within 2s
Sigma-Delta
None
Hardware User Manual, 1st Edition, Rev. B
3–47
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-06RTD Analog Input (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Heat Dissipation
300mW
Enclosure Type
Open Equipment
Module Keying to Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Removable terminal block (included).
The P2-06RTD module is not compatible with the
ZIPLink wiring system.
EU Directive
See the “EU Directive” topic in the Productivity Suite
Help File. Information can also be obtained at:
www.productivity2000.com
Connector Type (Included)
18-position removable terminal block
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the Declaration of Conformity for details.
Removable Terminal Block Specifications
Part Number
3–48
P2-RTB (included)
P2-RTB-1
Number of
positions
18 Screw Terminals
18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation
Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation
Maximum
19/64 in (7–8 mm) Strip Length
Conductors
“USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver
Width
1/8 in (3.8 mm) Maximum
Screw Size
M2
N/A
Screw Torque
2.5 lb·in (0.28 N·m)
N/A
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-06RTD Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Resistance Input Specifications
Internal Resolution
16 bit, .0015% of full scale range in ohms
(up to 100Hz filter)
Resistance Input Ranges and
CPU Resolution
0–10,000V,
Resolution 1V
0–6,250V,
Resolution 0.1 V
0–3,125V,
Resolution 0.1 V
0–1,562.5 V, Resolution 0.1 V
0–781.25 V,
Resolution 0.1 V
0–390.625 V, Resolution .01 V
0–195.3125 V, Resolution .01 V
Accuracy vs. Temperature
±25PPM per °C (maximum)
Full Scale Calibration
± 0.02% of full scale range
Offset Calibration Error
± 0.0015% of full scale range in ohms
Linearity Error (end to end)
± 0.0015% of full scale range maximum at
25°C, Monotonic with no missing codes
Maximum Inaccuracy
± 0.10% of full scale range
Diagnostics
Module Diagnostics Failure
1 bit per module
Module Not Ready
1 bit per module
Channel Burn-out (RTD only)
1 bit per channel
Under-range (RTD only)
1 bit per channel
Over-range
1 bit per channel
2000
Hardware User Manual, 1st Edition, Rev. B
3–49
Chapter 3: Analog I/O Specifications
Wiring Diagrams
INTERNAL
MODULE CIRCUITRY
R1+
R1COM
R2+
R2COM
R3+
R3COM
R4+
R4COM
R5+
R5COM
R6+
R6COM
CH1 RTD
INPUT
1
2
3
CH2 RTD
INPUT
4
5
6
CH3 RTD
INPUT
7
8
9 10 11 12 13 14 15 16 17 18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-06RTD Analog Input (continued)
CH4 RTD
INPUT
CH5 RTD
INPUT
CH6 RTD
INPUT
ANALOG CIRCUIT COMMON
R+
RCOM
Note: Jumper unused
inputs to common.
3–50
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-06RTD Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Wiring Diagrams
Resistance Input
RTD Input Circuits
2-wire RTD
R+
R+
R-
RCOM
COM
Note: Connect two wires to
one side of a 2-wire RTD.
3-wire RTD
R+
RCOM
4-wire RTD
R+
RNote:
Leave 4th
wire unattached as shown.
COM
Notes:
For maximum accuracy follow these guidelines.
1. For 2-wire RTD, attach third wire to module common.
2. R+, R-, and COM wires to an RTD must be equal length and type.
Refer to RTD manufacturer’s recommendations.
3. Do not use cable shield as sensing wire.
4. When applicable, connect shield to RTD common only, otherwise
connect to module common only. Do not connect shield at both ends.
2000
Hardware User Manual, 1st Edition, Rev. B
3–51
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-06RTD Analog Input (continued)
Module Configuration
Using the Hardware Configuration tool in the Productivity
Suite programming software, drag and drop the P2-06RTD
module into the base configuration.
Select Automatic Module Verification or No Verification and
Enable Hot Swap. Then select Input Range, Digital Filter,
Temperature Scale and Burnout Detection. If desired, assign
a User Tagname to each input point (channel) selected and
to each Status Bit Item.
3–52
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-06RTD Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
OLED Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
Hold SEL button down to cycle through primary
screens. Release button to select screen.
DISPLAY
SETUP
INFO
DISPLAY
STATUS
INFO
°C/°F/Ω
These screens will
then auto cycle
P2-06RTD
Fw. Rev.
1.00
RTD
Resistor
Module
°C/°F/Ω
Cu10/25
(j)Pt100
Pt1000
Ni120
Channels
AND
BOEnable
Control
Dig.Filt
10/50/60
100/250
Hz
End of
Setup
Menu
List
DISPLAY
UNITS
Momentarily
Press SEL
1 123.4
button to toggle
this secondary 2 56.7
3 1152
display.
4 - 8.4
These screens will
then auto cycle
Channels
Enabled:
5
Range
Resistor
0-10000
Burnout
L
Output
°F
Digital
Filter
60Hz
OR
1
2
3
4
5
6
Software
Configuration
Resistor Range also
includes 0-6250,
0-3125, 0-1562.5,
0-781.25, 0-390.625,
and 0-195.3125.
Data output can also be represented by
°C, °F, or Ω.
Digital Filter can be also be set to 50Hz,
60Hz, 100Hz and 250Hz
123.5
56.7
1152
- 8.4
238.6
SPARE
SELFTEST
FAIL
REPLACE
MODULE
MISSING
CONFIG
DATA
End of
Status
Menu
List
Note: SPARE
denotes
deselected
channel
RTD range also
includes Pt100,
Pt1000, Ni120,
Cu10 or Cu25.
Burnout detection may be set for H (high
side) or L (low side).
2000
5 238.6
6 SPARE
Range
jPt100
Error Messages:
An existing error will
be inserted into the
cycling Status Info
screen.
Fault Messages – Appear in place of data during
a fault condition.
Measured temp. > max. or
resistance >= max. of
selected range
1
2
3
OVER
UNDER
OPEN
Measured temp. < min. of
selected range or resistance
is 0
If open circuit between
differential input
(Rn+ and Rn-)
Hardware User Manual, 1st Edition, Rev. B
3–53
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08THM Analog Input
The P2-08THM Thermocouple Input Module provides eight differential channels for receiving
thermocouple and voltage input signals.
C
UL
R
Thermocouple Input Specifications
US
1
OVER
2J 0526 °C
3E 1000 F°
4
UNDER
5
OVER
V
6 21.35 M
7 1.245 M
V
8
SPARE
Input Channels
8 Differential
Data Format
Floating Point
Common Mode Range
±1.25 V
Common Mode Rejection
100dB @ DC and 130dB @ 60Hz
Input Impedance
>5MΩ
Maximum Ratings
Fault protected inputs to ±50V
Resolution
16-bit, ±0.1°C or °F
Thermocouple Input Ranges
Type J -190° to 760°C (-310° to 1400°F);
Type E -210° to 1000°C (-346° to 1832°F);
Type K -150° to 1372°C (-238° to 2502°F);
Type R 65° to 1768°C (149° to 3214°F);
Type S 65° to 1768°C (149° to 3214°F);
Type T -230° to 400°C (-382° to 752°F);
Type B 529° to 1820°C (984° to 3308°F);
Type N -70° to 1300°C (-94° to 2372°F);
Type C 65° to 2320°C (149° to 4208°F);
Cold Junction Compensation
Automatic
Thermocouple Linearization
Automatic
Accuracy vs. Temperature
±50PPM per °C (maximum)
Linearity Error
±1°C maximum (±0.5°C typical)
Monotonic with no missing codes.
Maximum Inaccuracy
±3°C maximum (including temperature drift
but excluding thermocouple error).
Warm-up Time
30 minutes for ±1% repeatability
2 minutes to reach voltage specifications
Sample Duration Time
270ms
All Channel Update Rate
2.16 s
Open Circuit Detection Time
Within 2s
Conversion Method
Sigma-Delta
External DC Power Required
None
Voltage Input Specifications
Terminal Block Included. Not
Compatible with ZIPLink.
Warranty: Thirty-day moneyback guarantee. Two-year
limited replacement. (See www.
productivity2000.com for details).
3–54
2000
Linear mV Device Input Ranges
0–39.0625 mVDC,
±39.0625 mVDC,
±78.125 mVDC,
0–156.25 mVDC,
±156.25 mVDC,
0–1250 mVDC
Max Voltage Input Offset Error
0.05% @ 0°– 60°C, typical 0.04% @ 25°C
Max Voltage Input Gain Error
0.06% @ 25°C
Max Voltage Input Linearity Error
0.05% @ 0°– 60°C, typical 0.03% @ 25°C
Max Voltage Input Impedance
0.2% @ 0°– 60°C, typical 0.06% @ 25°C
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08THM Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation
1800VAC applied for 1 second
Heat Dissipation
500mW
Enclosure Type
Open Equipment
Module Keying to
Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Removable terminal block (included).
The P2-08THM module is not compatible with
the ZIPLink wiring system.
EU Directive
See the “EU Directive” topic in the Productivity
Suite Help File. Information can also be
obtained at:
www.productivity2000.com
Connector Type (Included)
18-position removable terminal block
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Configuration/Diagnostics
Burn-out Detection: High Side/Disable
1 bit per module
°C/°F (T/C Only)
1 bit per module
Module Diagnostics Failure
1 bit per module
Burn-out (on if T/C input is open – no
connection between TCn+ and TCn-)
1 bit per channel
Channel Under-range (T/C only)
1 bit per channel
Channel Over-range (T/C only)
1 bit per channel
2000
Hardware User Manual, 1st Edition, Rev. B
3–55
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08THM Analog Input (continued)
Removable Terminal Block Specifications
Part Number
P2-RTB (included)
P2-RTB-1
Number of
positions
18 Screw Terminals
18 Spring Clamp Terminals
Wire Range*
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
Conductors*
Use Thermocouple Extension wire for thermocouples.
Use copper conductors, 75°C or equivalent for millivolt inputs.
Screw Driver
Width
1/8 in (3.8 mm) Maximum
Screw Size
M2
N/A
Screw Torque
2.5 lb·in (0.28 N·m)
N/A
* Use shielded, twisted thermocouple wire that matches the thermocouple type.
3–56
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08THM Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Wiring Diagrams
INTERNAL
MODULE CIRCUITRY
CH1 T/C
INPUT
1
TC1+
TC1TC2+
TC2-
2
3
4
CH2 T/C
INPUT
5
CH3 T/C
INPUT
6
TC3+
TC3TC4+
TC4TC5+
TC5TC6+
TC6-
7
8
CH4 T/C
INPUT
9 10 11 12 13 14 15 16 17 18
TC7+
TC7TC8+
TC8-
CH5 T/C
INPUT
CH6 T/C
INPUT
CH7 T/C
INPUT
CH8 T/C
INPUT
TC+
TCNOTE: Install jumper wire on each
unused input; TC+ to TC-.
2000
Hardware User Manual, 1st Edition, Rev. B
3–57
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08THM Analog Input (continued)
Wiring Diagrams
Thermocouple Input Circuits
Ungrounded/Shielded
Thermocouple
TC+
TC-
Voltage Input Circuits
TC+
4-wire
Voltage
Transmitter
TC-
Transmitter
Power Supply
AC or DC
Grounded/Shielded
Thermocouple
TC+
TC-
AC or DC
Infrared
Thermocouple
TC+
Load Cell
or
Strain Gauge
TC-
Excitation
Power Supply
Voltage Divider
TC+
TC-
TC+
TC-
NOTES:
1. Connect shield to thermocouple signal/ground only. Do not connect
to both ends.
2. W
ith grounded thermocouples, take precautions to prevent having
a voltage potential between thermocouple tips. A voltage of 1.25V
or greater between tips will skew measurements.
3. U
se shielded, twisted thermocouple extension wire that matches
the thermocouple type. Use thermocouple-compatible junction
blocks.
3–58
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08THM Analog Input (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Module Configuration
Using the Hardware Configuration tool in the Productivity Suite
programming software, drag and drop the P2-08THM module
into the base configuration.
Select Automatic Module Verification or No Verification and
Enable Hot Swap. Specify Temperature Scale and Burnout
Detection, and use the drop down menu to select module range
and resolution. If desired, assign a User Tagname to each input
point (channel) selected and to each Status Bit Item.
2000
Hardware User Manual, 1st Edition, Rev. B
3–59
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08THM Analog Input (continued)
OLED Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
Hold SEL button down to cycle through primary screens. Release
button to
DISPLAY
DISPLAY
DISPLAY
select
UNITS
SETUP
STATUS
screen.
DECIMAL
INFO
INFO
COUNTS
These screens will
then auto cycle
This screen will
auto cycle with
status information
P2-08THM
Fw. Rev.
1.00
End of
Status
Menu
List
16-BIT
Momentarily
Press SEL
button to
toggle
through
secondary
displays
Error Messages:
An existing error
will be inserted
into the cycling
Status Info screen.
7 CH
ENABLED
SELFTEST
FAIL
REPLACE
MODULE
MISSING
CONFIG
DATA
Fault Messages
– Appear in place
of data during a
fault condition.
3–60
1
2
3
4
OVER
UNDER
OPEN
1J 000°F
2E 000°F
3 00.0mV
4 0.000V
5 00.0mV
6 00.0mV
7 00.0mV
8 SPARE
Note: Volts, Celsius, or
Fahrenheit values are
specified with the P2-08THM
Module Options configuration
dialog box in Productivity Suite
software.
Note: SPARE denotes
deselected channel.
1J 000°F
2E 000°F
3 00.0mV
4 0.000V
5 00.0mV
6 00.0mV
7 00.0mV
8
SPARE
End of
Status
Menu
List
Measured temperature > max. temperature of selected range.
Measured temperature < min. temperature of selected range.
Input signal is OPEN circuit. (Thermocouple only)
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08NTC Thermistor
The P2-08NTC Thermistor Module provides eight channels for receiving thermistor input signals.
C
UL
R
US
NTC Input Specifications
Input Channels
8 Single Ended (Temperature only)
Data Format
Floating Point
Common Mode Rejection
-97dB @ DC, >50dB @ 50/60Hz*
Input Impedance
>5MΩ
Maximum Ratings
Fault protected inputs to ±50V
Resolution
16-bit, ±0.1°C or °F
Thermistor Input Ranges
2252
10K-AN Type 1
10K-CP Type 2
5K
3K
1.8K
Thermistor Linearizion
Automatic
Maximum Inaccuracy
±0.5°C maximum (8, 16 and 33Hz)
±1°C maximum (123 and 470Hz)
(Excluding thermistor error;
Including temperature drift)
Excitation Current
10uA - 210uA autoscaling
Accuracy vs. Temperature
±35PPM per °C (maximum)
Linearity Error
Non-linear
Warm-up Time
30 minutes for ±1°C repeatability
Sample Duration Time
(Single channel update rate)
Dependent on digital filter settings
250ms @ 8Hz, 125ms @ 16Hz, 61ms @ 33Hz,
16ms @123Hz, 4ms @ 470Hz
File Characteristics**
Digital filter cutoff frequencies: 8Hz*, 16Hz*, 33Hz,
123Hz, or 470Hz.
All Channel Update Rate
2.2s @ 16.7 Hz
Open Circuit Detection Time
Within 2s @ 16.7 Hz
Conversion Method
Sigma-Delta
External DC Power Required
None
-40° to 150°C (-40° to 302°F)
* 50/60Hz Noise rejection filtering enabled only when 125ms or 250ms Digital Filter is selected.
** Frequencies <123Hz, Display push button may need to be pressed / held >2 seconds..
Terminal Block Included.
Not Compatible with ZIPLink.
Warranty: Thirty-day money-back guarantee.
Two-year limited replacement.
(See www.productivity2000.com for details).
CPU Firmware Productivity Suite
P2-550
Version 1.2.2.x
Diagnostics
Module Diagnostics Failure
1 bit per module
Module Not Ready
1 bit per module
Channel Burn-out (Thermistor only)
1 bit per channel
Under-range (Thermistor only)
1 bit per channel
Over-range
1 bit per channel
Version 2.2.0.x
2000
Hardware User Manual, 1st Edition, Rev. B
3–61
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
c
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08NTC Thermistor (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation
1000VDC
Heat Dissipation
500mW
Enclosure Type
Open Equipment
Module Keying to
Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Removable terminal block (included).
The P2-08NTC module is not compatible
with the ZIPLink wiring system.
EU Directive
See the “EU Directive” topic in the
Productivity Suite Help File. Information can
also be obtained at:
www.productivity2000.com
Connector Type
(included)
18-position removable terminal block
Weight
136g (4.8 oz)
Agency Approvals**
UL508 File E139594, Canada & USA
CE (EN61131-2*)
*Meets EMC and Safety requirements. See the Declaration of Conformity for details.
**To obtain the most current agency approval information, see the Agency Approval
Checklist section on the specific component part number web page.
Removable Terminal Block Specifications
Part Number
3–62
P2-RTB (included)
P2-RTB-1
Number of
positions
18 Screw Terminals
18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
Conductors
“USE COPPER CONDUCTORS”, 75°C or equivalent.
Screw Driver
Width
1/8 in (3.8 mm) Maximum
Screw Size
M2
N/A
Screw Torque
2.5 lb·in (0.28 N·m)
N/A
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08NTC Thermistor (continued)
Wiring Diagrams
NOTE: At module power-up Channel 1 must have a functional Thermistor connected so internal automatic
calibration is performed.
INTERNAL
MODULE CIRCUITRY
CH1-
3
4
5
6
8
9 10 11 12 13 14 15 16 17 18
Analog Switch
7
CH7+
CH7CH8+
CH8-
2
CH3+
CH3CH4+
CH4CH5+
CH5CH6+
CH6-
CH1+
1
CH1+
CH1CH2+
CH2-
Thermistor Input
Ref. Adj.
A to D
Converter
10 uA
Current
Source
ANALOG CIRCUIT COMMON
2000
Hardware User Manual, 1st Edition, Rev. B
3–63
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08NTC Thermistor (continued)
OLED Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
Hold SEL button down to cycle through primary
screens. Release button to select screen.
DISPLAY
SETUP
INFO
DISPLAY
STATUS
INFO
°C/°F
These screens will
then auto cycle
P2-08NTC
F/W Rev.
1.00
NTC TYPE
THERMIST
MODULE
°C/°F
2252
10K-1/2
5K,3K
1.8k
Channels
and
BOEnable
Control
Filter
8/16/33/
123/
470Hz
End of
Setup
Menu
List
3–64
DISPLAY
UNITS
These screens will
then auto cycle
Channels
Enabled:
7
Momentarily
Press SEL
1 123.4
button to toggle
this secondary 2 56.7
3 1152
display.
4 - 8.4
5 238.6
6 26.2
7 108.3
8 SPARE
Input
Range
2252
Burnout
L
Output
°F
1
2
3
4
5
6
7
8
Software
Configuration
NTC range also
includes 2252,
10K-3, 10K-2,
5K, 3K, 1.8K.
Data output... in °C or °F.
Digital Filter can be set to 16Hz, 33Hz,
123Hz, and 470Hz
2000
SELFTEST
FAIL
REPLACE
MODULE
MISSING
CONFIG
DATA
End of
Status
Menu
List
Note: SPARE
denotes
deselected
channel
Digital
Filter
8Hz
Burnout detection may be set for H (high
side) or L (low side).
123.5
56.7
1152
- 8.4
238.6
26.2
108.3
SPARE
Error Messages:
An existing error will
be inserted into the
cycling Status Info
screen.
Fault Messages – Appear in place of data during
a fault condition.
Measured temp. > max. or
resistance >= max. of
selected range
1
2
3
OVER
UNDER
OPEN
Measured temp. < min. of
selected range or resistance
is 0
If open circuit between
differential input
(Rn+ and Rn-)
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-04DA Analog Output
The P2-04DA Voltage/Current Analog Output Module provides four channels of ±10VDC
or 4–20 mA sinking/sourcing selectable outputs.
C
1+0.100V
2 4.00
3 13.78
4-4.741V
UL
R
US
Output Specifications
Output Channels
4
Module Signal Output Ranges
1) ±10VDC
2) 4–20mA (sinking or sourcing per channel)
Signal Resolution
16-bit
Resolution Value of LSB
(least significant bit)
±10V = 305μV/count
4–20 mA = 0.244 μA/count
1 LSB = 1 count
Data Range
0 to 65535 counts uni-polar and
-32768 to +32767 counts bi-polar
Output Type
Voltage outputs sourcing/sinking at 10mA max, or
Current outputs sinking or sourcing at 20mA max.
Output Value in Fault Mode
Voltage outputs 0V or 0mA current outputs
Load Impedance
(Minimum External Power Supply)
>1000Ω voltage outputs (19.2–30 VDC)
0–755Ω Sinking, 0–600Ω Sourcing (19.2 VDC)
0–875Ω Sinking, 0–700Ω Sourcing (21.6 VDC)
0–1000Ω Sinking, 0–855Ω Sourcing (24VDC)
0–1110Ω Sinking, 0–970Ω Sourcing (26.4 VDC)
0–1350 Ω Sinking, 0–1150Ω Sourcing (30VDC)
Maximum Capacitive Load
0.01 μF maximum voltage outputs
Maximum Inductive Load
1mH maximum current outputs
Allowed Load Type
Grounded
Maximum Inaccuracy (% of range)
0.1% voltage, 0.1% current
(including temperature drift)
Maximum Full Scale Calibration
Error (not including offset error)
±0.025% of range maximum voltage outputs
±0.025% of range maximum current outputs
Maximum Offset Calibration Error
±0.025% of range maximum
Accuracy vs. Temperature
±25PPM/°C max full scale, calibration change
(±0.0025% of range/°C)
Max Crosstalk
-80dB, 6 LSB
Linearity Error (End to End)
±16 LSB maximum (±0.025% of full scale)
Monotonic with no missing codes
Output Stability and Repeatability
±10 LSB after 10 minute warm-up (typical)
Output Ripple
0.05% of full scale
Output Setting Time
0.3 ms max, 5μs min (full scale change)
All Channel Update Rate
0.6 ms
Maximum Continuous Overload
Voltage Outputs current limited to 35mA typical
Current Outputs open circuit protected
Type of Output Protection
15VDC Peak Output Voltage
Current outputs current limited to <=20mA
Output Signal (power-up,-down)
0V voltage outputs, 0mA current outputs
External DC Power Required
94mA voltage operation 4 channels
130mA current operation 4 channels
24VDC -20% / +25%
We recommend using pre-wired ZIPLink cables and connection modules. See Chapter 5.
If you wish to hand-wire your module, removable terminal blocks are sold separately. Order part number P2-RTB or
P2-RTB-1
2000
Hardware User Manual, 1st Edition, Rev. B
3–65
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-04DA Analog Output (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation
1800VAC applied for 1 second
Insulation Resistance
> 10MΩ @ 500VDC
Heat Dissipation
3.6 W
Enclosure Type
Open Equipment
Module Keying to Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Use ZIPLink Wiring System or removable terminal block
(not included). See “Wiring Options” in Chapter 5.
EU Directive
See the “EU Directive” topic in the Productivity Suite Help
File. Information can also be obtained at:
www.productivity2000.com
Connector Type (Not included)
18-position removable terminal block
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Removable Terminal Block Specifications
Part Number
3–66
P2-RTB
P2-RTB-1
Number of
positions
18 Screw Terminals
18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
Conductors
“USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver
Width
1/8 in (3.8 mm) Maximum
Screw Size
M2
N/A
Screw Torque
2.5 lb·in (0.28 N·m)
N/A
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-04DA Analog Output (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Wiring Diagrams
INTERNAL
MODULE CIRCUITRY
4-20 mA current sourcing
CH1
DAC
5
6
7
8
9 10 11 12 13 14 15 16 17 18
24VDC+
4-20 mA current sinking
4
+
voltage sink/source
3
-
2
24 VDC User
Supplied Power
24VDC+
24VDCV3+
I3I3+
COM
V4+
I4I4+
1
24VDC+
V1+
I1I1+
COM
V2+
I2I2+
voltage sink/source
4-20 mA current sinking
4-20 mA current sourcing
CH2
DAC
voltage sink/source
4-20 mA current sinking
4-20 mA current sourcing
CH3
DAC
voltage sink/source
4-20 mA current sinking
4-20 mA current sourcing
CH4
DAC
ANALOG
CIRCUIT
POWER
ANALOG
CIRCUIT COMMON
2000
Hardware User Manual, 1st Edition, Rev. B
3–67
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-04DA Analog Output (continued)
Wiring Diagrams (continued)
Voltage Output
Current Source Output
(Field device is sinking)
V+
0 - 10
VDC Load
COM
I+
4 - 20mA
Load
COM
24 VDC User
Supplied Power
AC or DC
V+
±10 VDC
Load
+
AC or DC
Transmitter
Power Supply
I-
I+
4-wire
4 - 20mA Load
COM
AC or DC
-
COM
-
+
I-
24 VDC User
Supplied Power
Current Sink Output
(Field device is sourcing)
2-wire
4 - 20mA Load
NOTE: Shield is connected to
common at the source device.
+24VDC User
Supplied Power
I-
Install
Jumper
AC or DC
3–68
2000
I+
24VDC+
4-wire
4 - 20mA Load
Transmitter
Power Supply
COM
I-
Install
Jumper
Hardware User Manual, 1st Edition, Rev. B
COM
I+
Chapter 3: Analog I/O Specifications
P2-04DA Analog Output (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Configuration Settings
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-04DA module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each output point
(channel) selected and to each Status Bit Item.
Range with sink/source option and Stop Mode
Value may also be assigned.
2000
Hardware User Manual, 1st Edition, Rev. B
3–69
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-04DA Analog Output (continued)
OLED Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
These screens will
then auto cycle
P2-04DA
Fw. Rev.
1.00
1
2
3
4
+/-10V
mA SRC
mA SNK
+/-10V
3–70
Hold SEL button down to cycle through primary screens. Release button to select screen.
DISPLAY
SETUP
INFO
This screen will
auto cycle with
status information
End of
Status
Menu
List
Error Messages:
An existing error will
be inserted into the
cycling Status Info
screen.
2000
DISPLAY
STATUS
INFO
DISPLAY
UNITS
DECIMAL
COUNTS
Momentarily Press
SEL button to
toggle through
secondary displays
MISSING
EXTERNAL
24VDC
1
2
3
4
00000
00000
00000
00000
SELFTEST
FAIL
REPLACE
MODULE
DISPLAY
UNITS
HEX
COUNTS
1
2
3
4
DISPLAY
UNITS
VOLT OR
MILLIAMP
0000H
0000H
0000H
0000H
MISSING
CONFIG
DATA
1 0.000V
2 4.00
3 13.90
4-4.741V
End of
Status
Menu
List
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08DA-1 Current Analog Output
The P2-08DA-1 Current Analog Output Module provides eight channels of 4 to 20 mA
outputs.
C
1
2
3
4
5
6
7
8
UL
R
Output Specifications
US
18.23
14.23
4.00
4.23
13.56
16.32
8.00
7.54
Output Channels (Commons)
8
Module Signal Output Range
4–20mA
Output Signal Resolution
16-bit
Resolution Value of LSB
(least significant bit)
4–20mA = 0.244 μA/count
1 LSB = 1 count
Data Range
0 to 65535 counts
Output Type (sourcing)
Current: 20mA max
Output Value in Fault Mode
Near 0mA
Load Impedance
(Minimum External Power
Supply)
0–570Ω (19.2 VDC)
0–690Ω (21.6 VDC)
0–810Ω (24VDC)
0–930Ω (26.4 VDC)
0–1100Ω (30VDC)
Minimum Load 0–125Ω @ 0–45°C
250–715Ω @ 0–60°C
Maximum Inductive Load
1mH
Allowed Load Type
Grounded
Maximum Inaccuracy
0.1% of range (Counts TBD)
(including temperature drift)
Maximum Full Scale Calibration
Error (not including offset error)
Maximum Offset Calibration Error
±0.025% of range maximum
±0.025% of range maximum
Accuracy vs. Temperature
±25PPM/°C max full scale calibration
change
(±0.0025% of range/°C)
Max Crosstalk
-96dB, 1 LSB
Linearity Error (End to End)
±16 LSB maximum (±0.025% of full scale)
Monotonic with no missing codes
Output Stability and Repeatability
±10 count after 10 minute warm-up
(typical)
Output Ripple
0.05% of full scale
Output Setting Time
300μs max, 5μs min (full scale change)
All Channel Update Rate
600μs
Maximum Continuous Overload
Outputs open circuit protected
Type of Output Protection
Electronically current limited to 20mA or
less
Output Signal (power-up,-down)
4mA
External DC Power Required
24VDC @ 220mA (Loop Power Included)
We recommend using pre-wired ZIPLink cables
and connection modules. See Chapter 5.
If you wish to hand-wire your module, removable
terminal blocks are sold separately. Order part
number P2-RTB or P2-RTB-1
2000
Hardware User Manual, 1st Edition, Rev. B
3–71
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08DA-1 Current Analog Output (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation
1800VAC applied for 1 second
Insulation Resistance
>10MΩ @ 500VDC
Heat Dissipation
700mW
Enclosure Type
Open Equipment
Module Keying to Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Use ZIPLink Wiring System or removable
terminal block (not included). See “Wiring
Options” in Chapter 5.
EU Directive
See the “EU Directive” topic in the
Productivity Suite Help File. Information
can also be obtained at:
www.productivity2000.com
Connector Type (Not included)
18-position removable terminal block
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Removable Terminal Block Specifications
Part Number
3–72
P2-RTB
P2-RTB-1
Number of
positions
18 Screw Terminals
18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
Conductors
“USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver Width
1/8 in (3.8 mm) Maximum
Screw Size
M2
N/A
Screw Torque
2.5 lb·in (0.28 N·m)
N/A
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08DA-1 Current Analog Output (continued)
Wiring Diagrams
INTERNAL
MODULE CIRCUITRY
2
4-20 mA current sourcing
3
4-20 mA current sourcing
4
4-20 mA current sourcing
5
4-20 mA current sourcing
6
4-20 mA current sourcing
7
4-20 mA current sourcing
8
4-20 mA current sourcing
9 10 11 12 13 14 15 16 17 18
+
1
-
COM
I1+
I2+
I3+
I4+
I5+
I6+
I7+
I8+
COM
COM
COM
COM
COM
COM
COM
0V
24V+
4-20 mA current sourcing
CH1 ADC
CH2 ADC
CH3 ADC
CH4 ADC
CH5 ADC
CH6 ADC
CH7 ADC
CH8 ADC
ISOLATED ANALOG
CIRCUIT POWER
24 VDC User
Supplied Power
ISOLATED ANALOG
CIRCUIT COMMON
Current Source Output Circuit
4 - 20mA
Load
Note: Shield is connected to common at the source device.
2000
Hardware User Manual, 1st Edition, Rev. B
3–73
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08DA-1 Current Analog Output (continued)
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-08DA-1 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each output point
(channel) selected and to each Status Bit Item.
A Stop Mode Value may also be assigned.
3–74
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08DA-1 Current Analog Output (continued)
OLED Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
Hold SEL button down to cycle through primary screens. Release button to select screen.
DISPLAY
SETUP
INFO
DISPLAY
STATUS
INFO
DISPLAY
UNITS
HEX
COUNTS
DISPLAY
UNITS
DECIMAL
COUNTS
DISPLAY
UNITS
MILLIAMP
4-20mA
These screens will
then auto cycle
P2-08DA1
Fw. Rev.
1.00
16-BIT
4-20mA
This screen will
auto cycle with
status information
Momentarily Press
SEL button to
toggle through
secondary displays
End of
Status
Menu
List
Error Messages – An existing error will be
inserted into the cycling Status Info screen.
MISSING
EXTERNAL
24VDC
SELFTEST
FAIL
REPLACE
MODULE
End of
Status
Menu
List
MISSING
CONFIG
DATA
2000
1
2
3
4
0
0
0
0
1
2
3
4
0000H
0000H
0000H
0000H
1
2
3
4
0.00
0.00
0.00
0.00
5
6
7
8
0
0
0
0
5
6
7
8
0000H
0000H
0000H
0000H
5
6
7
8
0.00
0.00
0.00
0.00
1
2
3
4
5
6
7
8
0
0
0
0
0
0
0
0
1
2
3
4
5
6
7
8
0000H
0000H
0000H
0000H
0000H
0000H
0000H
0000H
1
2
3
4
5
6
7
8
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
Hardware User Manual, 1st Edition, Rev. B
3–75
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08DA-2 Voltage Analog Output
The P2-08DA-2 Voltage Analog Output Module provides eight channels of ±10 VDC outputs
for use with the Productivity2000 Ssystem.
C
UL
R
Output Specifications
US
1 +1.823V
2+1.423V
3–4.000V
4–9.999V
5–6.175V
6+8.320V
7–7.235V
8+9.936V
Output Channels (Commons)
8
Module Signal Output Range
±10VDC
Output Signal Resolution
16-bit
Resolution Value of LSB
(least significant bit)
±10V = 305μV/count
1 LSB = 1 count
Data Range
-32768 to +32767 counts
Output Type (sourcing/sinking)
Voltage: 10mA max
Output Value in Fault Mode
0V
Load Impedance
≤1000Ω
Maximum Capacitive Load
0.01 μF
Allowed Load Type
Grounded
Maximum Inaccuracy
0.1% of range
(including temperature drift)
Maximum Full Scale Calibration
Error (not including offset error)
±0.025% of range maximum
Maximum Offset Calibration Error
±0.025% of range maximum
Accuracy vs. Temperature
±25PPM/°C max full scale calibration
change
(±0.0025% of range/°C)
Max Crosstalk
-96dB, 1 LSB
Linearity Error (End to End)
±16 LSB maximum (±0.025% of full scale)
Monotonic with no missing codes
Output Stability and Repeatability
±10 LSB after 10 minute warm-up (typical)
Output Ripple
0.05% of full scale
Output Setting Time
300μs max, 5μs min (full scale change)
All Channel Update Rate
1ms
Maximum Continuous Overload
Outputs current limited to 40mA typical
Continous overloads on multiple outputs
can damage the module.
Type of Output Protection
0.1 μF Transient Suppressor
Output Signal (power-up,-down)
0V
External DC Power Required
24VDC @ 150mA
We recommend using pre-wired ZIPLink cables
and connection modules. See Chapter 5.
If you wish to hand-wire your module, removable
terminal blocks are sold separately. Order part
number P2-RTB or P2-RTB-1
3–76
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08DA-2 Voltage Analog Output (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation
1800VAC applied for 1 second
Insulation Resistance
> 10MΩ @ 500VDC
Heat Dissipation
150mW
Enclosure Type
Open Equipment
Module Keying to Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Use ZIPLink Wiring System or removable
terminal block (not included). See “Wiring
Options” in Chapter 5.
EU Directive
See the “EU Directive” topic in the
Productivity Suite Help File. Information
can also be obtained at:
www.productivity2000.com
Connector Type (Not included)
18-position removable terminal block
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Removable Terminal Block Specifications
Part Number
P2-RTB
P2-RTB-1
Number of positions
18 Screw Terminals
18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
Conductors
“USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver Width
1/8 in (3.8 mm) Maximum
Screw Size
M2
N/A
Screw Torque
2.5 lb·in (0.28 N·m)
N/A
2000
Hardware User Manual, 1st Edition, Rev. B
3–77
Chapter 3: Analog I/O Specifications
Wiring Diagrams
INTERNAL
MODULE CIRCUITRY
voltage sink/source
3
voltage sink/source
4
voltage sink/source
5
voltage sink/source
6
voltage sink/source
7
voltage sink/source
8
voltage sink/source
CH1 DAC
CH2 DAC
CH3 DAC
CH4 DAC
CH5 DAC
CH6 DAC
CH7 DAC
voltage sink/source
9 10 11 12 13 14 15 16 17 18
+
2
-
COM
V1+
V2+
V3+
V4+
V5+
V6+
V7+
V8+
COM
COM
COM
COM
COM
COM
COM
0V
24V+
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08DA-2 Voltage Analog Output (continued)
CH8 DAC
ISOLATED ANALOG
CIRCUIT POWER
24 VDC User
Supplied Power
ISOLATED ANALOG
CIRCUIT COMMON
Voltage Output Circuits
V+
0 - 10
VDC Load
COM
Load
Power Supply
V+
±10 VDC
Load
COM
Load
Power Supply
V+
-10 - 0
VDC Load
COM
Load
Power Supply
3–78
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08DA-2 Voltage Analog Output (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Module Configuration
Using the Hardware Configuration tool in
the Productivity Suite programming software,
drag and drop the P2-08DA-2 module into
the base configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap and Stop
Mode Values. If desired, assign a User
Tagname to each output point (channel)
selected and to each Status Bit Item.
2000
Hardware User Manual, 1st Edition, Rev. B
3–79
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08DA-2 Voltage Analog Output (continued)
OLED Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
Hold SEL button down to cycle through primary screens. Release button to select screen.
DISPLAY
SETUP
INFO
DISPLAY
STATUS
INFO
DISPLAY
UNITS
HEX
COUNTS
DISPLAY
UNITS
DECIMAL
COUNTS
DISPLAY
UNITS
VOLTAGE
+/-9.99V
These screens will
then auto cycle
P2-08DA2
Fw. Rev.
1.00
16-BIT
+/-10V
3–80
This screen will
auto cycle with
status information
End of
Status
Menu
List
Momentarily Press
SEL button to
toggle through
secondary displays
Error Messages – An existing error will be
inserted into the cycling Status Info screen.
MISSING
EXTERNAL
24VDC
SELFTEST
FAIL
REPLACE
MODULE
End of
Status
Menu
List
MISSING
CONFIG
DATA
2000
1
2
3
4
0
0
0
0
1
2
3
4
0000H
0000H
0000H
0000H
1
2
3
4
0.00V
0.00V
0.00V
0.00V
5
6
7
8
0
0
0
0
5
6
7
8
0000H
0000H
0000H
0000H
5
6
7
8
0.00V
0.00V
0.00V
0.00V
1
2
3
4
5
6
7
8
0
0
0
0
0
0
0
0
1
2
3
4
5
6
7
8
0000H
0000H
0000H
0000H
0000H
0000H
0000H
0000H
1
2
3
4
5
6
7
8
0.00V
0.00V
0.00V
0.00V
0.00V
0.00V
0.00V
0.00V
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08DAL-1 Current Analog Output
The P2-08DAL-1 Low Resolution Current Analog Output Module provides eight channels
of 4–20 mA output signals.
C
UL
R
US
Output Specifications
Output Channels
8
Module Signal Output Range
4–20mA
Signal Resolution
Resolution Value of LSB
(least significant bit)
Data Range
12-bit
4–20mA = 3.9 μA / count
1 LSB = 1 count
0 to 4095 counts
Output Type (sourcing)
Current sourcing at 20mA max
Output Value in Fault Mode
Less than 4mA
Load Impedance
0–570Ω (19.2 VDC),
0–690Ω (21.6 VDC),
0–810Ω (24VDC),
0–930Ω (26.4 VDC),
0–1100Ω (30VDC)
Minimum Load: 0Ω @ 0–45°C
125Ω @ 45-60°C ambient temperature
Maximum Inductive Load
1mH
Allowed Load Type
Grounded
Maximum Inaccuracy
1% of range
Maximum Full Scale Calibration Error
(Including Offset)
±0.2% of range minimum
Maximum Offset Calibration Error
±0.2% of range maximum
Accuracy vs. Temperature
±75PPM / °C maximum full-scale
calibration change
(±0.005% of range / °C)
Max Crosstalk at DC, 50/60Hz
-72dB, 1 LSB
Linearity Error (End to End)
±4 LSB max., (±0.1% of full scale)
Output Stability and Repeatability
±2 count after 10 min. warm up (typical)
Output Ripple
±0.1% of full scale
Output Settling Time
300µs max., 5µs min. (full scale range)
All Channel Update Rate
1ms
Maximum Continuous Overload
Outputs open circuit protected
Electronically current limited to 20mA
or less
Type of Output Protection
Output Signal at Power Up
and Power Down
External DC Power Required
4mA
24VDC (-20% / +25%) @ 220mA
(Loop Power Included)
We recommend using pre-wired ZIPLink cables
and connection modules. See Chapter 5.
If you wish to hand-wire your module, removable
terminal blocks are sold separately. Order part
number P2-RTB or P2-RTB-1
2000
Hardware User Manual, 1st Edition, Rev. B
3–81
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08DAL-1 Current Analog Output (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation
1800VAC applied for 1 second
Insulation Resistance
>10MΩ @ 500VDC
Heat Dissipation
6000mW Maximum (Loop Power Included)
Enclosure Type
Open Equipment
Module Keying to
Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Use ZIPLink Wiring System or removable
terminal block (not included). See “Wiring
Options” in Chapter 5.
EU Directive
See the “EU Directive” topic in the
Productivity Suite Help File. Information
can also be obtained at:
www.productivity2000.com
Terminal Type (not
included)
Weight
18-position Removable Terminal Block
90g (3.2 oz)
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Agency Approvals
3–82
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08DAL-1 Current Analog Output (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Wiring Diagrams
INTERNAL
MODULE CIRCUITRY
2
4-20mA current sourcing
3
4-20mA current sourcing
4
4-20mA current sourcing
5
4-20mA current sourcing
6
4-20mA current sourcing
7
4-20mA current sourcing
8
4-20mA current sourcing
9 10 11 12 13 14 15 16 17 18
+
1
-
COM
I1+
I2+
I3+
I4+
I5+
I6+
I7+
I8+
COM
COM
COM
COM
COM
COM
COM
0V
24V+
4-20mA current sourcing
CH1 DAC
CH2 DAC
CH3 DAC
CH4 DAC
CH5 DAC
CH6 DAC
CH7 DAC
CH8 DAC
ISOLATED ANALOG
CIRCUIT POWER
24 VDC User
Supplied Power
ISOLATED ANALOG
CIRCUIT COMMON
Current Source Output Circuit
4 - 20mA
Load
Note: Shield is connected to common at the source device.
2000
Hardware User Manual, 1st Edition, Rev. B
3–83
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08DAL-1 Current Analog Output (continued)
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-08DAL-1 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each output point
(channel selected and to each Status Bit Item.
A Stop Mode Value may also be assigned.
12
3–84
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08DAL-2 Voltage Analog Output
The P2-08DAL-2 Low Resolution Voltage Analog Output Module provides eight channels of
0–10 VDC output signals.
C
UL
R
US
Output Specifications
Output Channels
Module Signal Input Range
8
0–10V
Output Signal Resolution
Data Range
12-bit
0–10V = 2.44 mV per count
1 LSB = 1 count
0 to 4095 counts
Output Type (Sinking/Sourcing)
Voltage: 10mA max
Output Value in Fault Mode
0V
Load Impedance
≥1000Ω
Maximum Capacitive Load
0.01 µF
Allowed Load Type
Grounded
0.5% of range
(including temperature drift)
Resolution Value of LSB
(least significant bit)
Maximum Inaccuracy
Maximum Full Scale Calibration
Error
(Not Including Offset)
Maximum Offset Calibration Error
Accuracy vs. Temperature
Max Crosstalk
±0.2% of range maximum
±0.2% of range maximum
±75PPM / °C maximum full-scale
calibration change
(±0.0025% of range / °C)
-72dB, 1 LSB
Linearity Error (End to End)
±4 LSB maximum, (±0.1% of full scale)
Monotonic with no missing codes
Output Stability and Repeatability
Output Ripple
±2% LSB after 10 min. warm up
(typical)
±0.1% of full scale
Output Settling Time
300µs max., 5µ min. (full scale range)
All Channel Update Rate (typical)
1ms
Outputs current limited to 40mA typical
Continuous overloads on multiple
outputs can damage the module.
0.1 µF Transient Suppressor
Maximum Continuous Overload
Type of Output Protection
Output Signal at Power Up and
Power Down
External 24VDC Power Required
0V
24VDC (-20% / +25%), 150mA
We recommend using pre-wired ZIPLink cables
and connection modules. See Chapter 5.
If you wish to hand-wire your module, removable
terminal blocks are sold separately. Order part
number P2-RTB or P2-RTB-1
2000
Hardware User Manual, 1st Edition, Rev. B
3–85
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-08DAL-2 Voltage Analog Output (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation
1800VAC applied for 1 second
Insulation Resistance
>10MΩ @ 500VDC
Heat Dissipation
3250mW
Enclosure Type
Open Equipment
Module Keying to Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Use ZIPLink Wiring System or removable
terminal block (not included). See “Wiring
Options” in Chapter 5.
EU Directive
See the “EU Directive” topic in the
Productivity Suite Help File. Information
can also be obtained at:
www.productivity2000.com
Connector Type (Not included)
18-position removable terminal block
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Removable Terminal Block Specifications
Part Number
P2-RTB
P2-RTB-1
Number of positions
18 Screw Terminals
18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7– 8 mm) Strip Length
Conductors
“USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver Width
1/8 in (3.8 mm) Maximum
Screw Size
M2
N/A
Screw Torque
2.5 lb·in (0.28 N·m)
N/A
3–86
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-08DAL-2 Voltage Analog Output (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Wiring Diagrams
INTERNAL
MODULE CIRCUITRY
2
voltage sink/source
3
voltage sink/source
4
voltage sink/source
5
voltage sink/source
6
voltage sink/source
7
voltage sink/source
8
voltage sink/source
9 10 11 12 13 14 15 16 17 18
+
1
-
COM
V1+
V2+
V3+
V4+
V5+
V6+
V7+
V8+
COM
COM
COM
COM
COM
COM
COM
0V
24V+
CH1 DAC
CH2 DAC
CH3 DAC
CH4 DAC
CH5 DAC
CH6 DAC
CH7 DAC
voltage sink/source
CH8 DAC
ISOLATED ANALOG
CIRCUIT POWER
24 VDC User
Supplied Power
ISOLATED ANALOG
CIRCUIT COMMON
Voltage Output Circuits
V+
0 - 10
VDC Load
COM
Load
Power Supply
2000
Hardware User Manual, 1st Edition, Rev. B
3–87
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
c
D
P2-08DAL-2 Voltage Analog Output (continued)
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-08DAL-2 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each output point
(channel selected and to each Status Bit Item.
A Stop Mode Value may also be assigned.
3–88
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16DA-1 Current Analog Output
The P2-16DA-1 Current Analog Output Module provides sixteen channels of 4–20 mA
sourcing output.
C
1
2
3
4
5
6
7
8
18.23
14.23
4.00
4.23
13.56
16.32
8.00
7.54
M
A
M
A
M
A
M
A
M
A
M
A
M
A
M
A
UL
R
US
Output Specifications
Output Channels
16
Module Signal Output Range
4–20mA (Sourcing)
Output Signal Resolution
16-bit
Resolution Value of LSB
(least significant bit)
4–20mA = 0.244 μA/count
1 LSB = 1 count
Data Range
0 to 65535 counts
Output Type (sourcing)
Current: 20mA max
Output Value in Fault Mode
Near 0mA
Load Impedance
(Minimum External Power
Supply)
0–570Ω (19.2 VDC)
0–690Ω (21.6 VDC)
0–810Ω (24VDC)
0–930Ω (26.4 VDC)
0–1100Ω (30VDC)
Minimum Load 0Ω @ 0–45°C
125Ω @ 45–60°C
Maximum Inductive Load
1mH
Allowed Load Type
Grounded
Maximum Inaccuracy
0.1% of range
(including temperature drift)
Maximum Full Scale Calibration
Error (not including offset error)
Maximum Offset Calibration Error
±0.025% of range maximum
±0.025% of range maximum
Accuracy vs. Temperature
±25PPM/°C max full scale calibration
change
(±0.0025% of range/°C)
Max Crosstalk
-96dB, 1 LSB
Linearity Error (End to End)
±16 LSB maximum (±0.025% of full scale)
Monotonic with no missing codes
Output Stability and Repeatability
±10 count after 10 minute warm-up
(typical)
Output Ripple
0.05% of full scale
Output Setting Time
300μs max, 5μs min (full scale change)
All Channel Update Rate
3ms
Maximum Continuous Overload
Outputs open circuit protected
Type of Output Protection
Electronically current limited to 20mA or
less
Output Signal (power-up,-down)
4mA
External DC Power Required
24VDC @ 410mA (includes loop power)
We recommend using pre-wired ZIPLink cables and
connection modules. See Chapter 5.
Module connector type is a 24-pin Molex Style
43025-2400.
2000
Hardware User Manual, 1st Edition, Rev. B
3–89
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16DA-1 Current Analog Output (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation
1800VAC applied for 1 second
Insulation Resistance
>10MΩ @ 500VDC
Heat Dissipation
96mW
Enclosure Type
Open Equipment
Module Keying to
Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Use ZIPLink Wiring System ONLY. See
“Wiring Options” in Chapter 5. Must use
copper conductors 75ºC or equivalent.
EU Directive
See the “EU Directive” topic in the
Productivity Suite Help File. Information
can also be obtained at:
www.productivity2000.com
Connector Type
24-Pin Molex Style 43025-2400
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Connector Specifications
3–90
Connector Type
24-Pin Molex Style 43025-2400
Number of Pins
24
Pin Spacing
3x3 mm (0.118 x 0.118 in)
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16DA-1 Current Analog Output (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Wiring Diagrams
INTERNAL
MODULE
CIRCUITRY
ZL-RTB20
Labels
COM
COM
COM
COM
I1+
I5+
I2+
I6+
I3+
I7+
I4+
I8+
+V
+V
-V
-V
I9+
I13+
I10+
I14+
I11+
I15+
I12+
I16+
+
13
1
14
2
15
3
16
4
17
5
18
6
19
7
20
8
21
9
22
10
23
11
24
12
CH1 ADC
CH5 ADC
CH2 ADC
CH6 ADC
CH3 ADC
CH7 ADC
CH4 ADC
CH8 ADC
CH9 ADC
CH13 ADC
CH10 ADC
CH14 ADC
CH11 ADC
CH15 ADC
CH12 ADC
CH16 ADC
ISOLATED
ANALOG
CIRCUIT
POWER
ISOLATED ANALOG
CIRCUIT COMMON
Current Sourcing Output Circuit
4 - 20mA
Load
Note: Shield is connected to common at the source device.
2000
Hardware User Manual, 1st Edition, Rev. B
3–91
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16DA-1 Current Analog Output (continued)
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-16DA-1 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each output point
(channel) selected and to each Status Bit Item.
A Stop Mode Value may also be assigned.
3–92
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16DA-1 Current Analog Output (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
OLED Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
Hold SEL button down to cycle through primary screens. Release button to select screen.
DISPLAY
SETUP
INFO
DISPLAY
UNITS
HEX
COUNTS
DISPLAY
UNITS
DECIMAL
COUNTS
DISPLAY
STATUS
INFO
DISPLAY
UNITS
MILLIAMP
4-20mA
These screens will
then auto cycle
P2-16DA1
Fw. Rev.
1.00
16-BIT
4-20mA
This screen will
auto cycle with
status information
End of
Status
Menu
List
Momentarily Press
SEL button to
toggle through
secondary displays
Error Messages – An existing error will be
inserted into the cycling Status Info screen.
MISSING
EXTERNAL
24VDC
SELFTEST
FAIL
REPLACE
MODULE
End of
Status
Menu
List
MISSING
CONFIG
DATA
1
2
3
4
0
0
0
0
1
2
3
4
0000H
0000H
0000H
0000H
1
2
3
4
4.00
4.00
4.00
4.00
5
6
7
8
0
0
0
0
5
6
7
8
0000H
0000H
0000H
0000H
5
6
7
8
4.00
4.00
4.00
4.00
9
10
11
12
0
0
0
0
9
10
11
12
0000H
0000H
0000H
0000H
9
10
11
12
4.00
4.00
4.00
4.00
13
14
15
16
0
0
0
0
13
14
15
16
0000H
0000H
0000H
0000H
13
14
15
16
4.00
4.00
4.00
4.00
1
2
3
4
5
6
7
8
0
0
0
0
0
0
0
0
1
2
3
4
5
6
7
8
0000H
0000H
0000H
0000H
0000H
0000H
0000H
0000H
1
2
3
4
5
6
7
8
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
9
10
11
12
13
14
15
16
0
0
0
0
0
0
0
0
9
10
11
12
13
14
15
16
0000H
0000H
0000H
0000H
0000H
0000H
0000H
0000H
9
10
11
12
13
14
15
16
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
Note:
SPARE
denotes
deselected
channel.
2000
Hardware User Manual, 1st Edition, Rev. B
3–93
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16DA-2 Voltage Analog Output
The P2-16DA-2 Voltage Analog Output Module provides sixteen channels of
±10VDC outputs.
C
UL
R
US
Output Specifications
1+1.823V
2+1.423V
3–4.000V
4–9.999V
5–6.175V
6+8.320V
7–7.225V
8+9.936V
Output Channels
16
Module Signal Output Range
±10VDC
Output Signal Resolution
16-bit
Resolution Value of LSB
(least significant bit)
±10VDC = 305μV/count
1 LSB = 1 count
Data Range
-32768 to 32767 counts
Output Type (sourcing/sinking)
Voltage: 10mA max current
Output Value in Fault Mode
0V
Load Impedance
≥1000Ω
Maximum Capacitive Load
0.01 μF maximum
Allowed Load Type
Grounded
Maximum Inaccuracy
0.1% of range
(including temperature drift)
Maximum Full Scale Calibration
Error (not including offset error)
Maximum Offset Calibration Error
±0.025% of range maximum
±0.025% of range maximum
Accuracy vs. Temperature
±25PPM/°C max full scale calibration
change
(±0.0025% of range/°C)
Max Crosstalk
-96dB, 1 LSB
Linearity Error (End to End)
±16 LSB maximum (±0.025% of full scale)
Monotonic with no missing codes
Output Stability and Repeatability
±10 LSB after 10 minute warm-up (typical)
Output Ripple
0.05% of full scale
Output Setting Time
300μs max, 5μs min (full scale change)
All Channel Update Rate
3ms
Maximum Continuous Overload
Outputs current limited to 40mA typical.
Continuous overloads on multiple output
can damage the module.
Type of Output Protection
0.1 μF Transient Suppressor
External DC Power Required
24VDC (-20% / +25%), 265mA
We recommend using pre-wired ZIPLink cables and
connection modules. See Chapter 5.
Module connector type is a 24-pin Molex Style
43025-2400.
3–94
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16DA-2 Voltage Analog Output (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation
1800VAC applied for 1 second
Insulation Resistance
>10MΩ @ 500VDC
Heat Dissipation
6.4 W
Enclosure Type
Open Equipment
Module Keying to
Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Use ZIPLink Wiring System ONLY. See
“Wiring Options” in Chapter 5. Must use
copper conductors 75ºC or equivalent.
EU Directive
See the “EU Directive” topic in the
Productivity Suite Help File. Information
can also be obtained at:
www.productivity2000.com
Connector Type
24-Pin Molex Style 43025-2400
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Connector Specifications
Connector Type
24-Pin Molex Style 43025-2400
Number of Pins
24
Pin Spacing
3x3 mm (0.118 x 0.118 in)
2000
Hardware User Manual, 1st Edition, Rev. B
3–95
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16DA-2 Voltage Analog Output (continued)
Wiring Diagrams
INTERNAL
MODULE
CIRCUITRY
COM
COM
COM
COM
V1+
V5+
V2+
V6+
V3+
V7+
V4+
V8+
+V
24VDC+/-10% +V
-V
-V
V9+
V13+
V10+
V14+
V11+
V15+
V12+
ZL-RTB20
V16+
Labels
+
13
1
14
2
15
3
16
4
17
5
18
6
19
7
20
8
21
9
22
10
23
11
24
12
CH1 ADC
CH5 ADC
CH2 ADC
CH6 ADC
CH3 ADC
CH7 ADC
CH4 ADC
CH8 ADC
CH9 ADC
CH13 ADC
CH10 ADC
CH14 ADC
CH11 ADC
CH15 ADC
CH12 ADC
CH16 ADC
ISOLATED
ANALOG
CIRCUIT
POWER
ISOLATED ANALOG
CIRCUIT COMMON
Voltage Output Circuits
V+
V+
0 - 10
VDC Load
COM
±10 VDC
Load
COM
Load
Power Supply
Load
Power Supply
V+
-10 - 0
VDC Load
COM
Load
Power Supply
3–96
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16DA-2 Voltage Analog Output (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-16DA-2 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each output point
(channel) selected and to each Status Bit Item.
2000
Hardware User Manual, 1st Edition, Rev. B
3–97
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16DA-2 Voltage Analog Output (continued)
LCD Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
Hold SEL button down to cycle through primary screens. Release button to select screen.
DISPLAY
SETUP
INFO
DISPLAY
STATUS
INFO
DISPLAY
UNITS
HEX
COUNTS
DISPLAY
UNITS
DECIMAL
COUNTS
DISPLAY
UNITS
VOLTS
+/-10VDC
These screens will
then auto cycle
P2-16DA2
Fw. Rev.
1.00
16-BIT
0-10VDC
15 CH
ENABLED
This screen will
auto cycle with
status information
End of
Status
Menu
List
Error Messages – An existing error will be
inserted into the cycling Status Info screen.
MISSING
EXTERNAL
24VDC
End of
Status
Menu
List
3–98
Momentarily Press
SEL button to
toggle through
secondary displays
SELFTEST
FAIL
REPLACE
MODULE
MISSING
CONFIG
DATA
2000
1
2
3
4
0
0
0
0
1
2
3
4
0000H
0000H
0000H
0000H
1+0.000V
2+0.000V
3+0.000V
4+0.000V
5
6
7
8
0
0
0
0
5
6
7
8
0000H
0000H
0000H
0000H
5+0.000V
6+0.000V
7+0.000V
8+0.000V
9
10
11
12
0
0
0
0
9
10
11
12
0000H
0000H
0000H
0000H
9+0.000V
10+0.00V
11+0.00V
12+0.00V
13
14
15
16
0
0
0
0
13
14
15
16
0000H
0000H
0000H
0000H
13+0.00V
14+0.00V
15+0.00V
16+0.00V
1
2
3
4
5
6
7
8
0
0
0
0
0
0
0
0
1
2
3
4
5
6
7
8
0000H
0000H
0000H
0000H
0000H
0000H
0000H
0000H
1+0.000V
2+0.000V
3+0.000V
4+0.000V
5+0.000V
6+0.000V
7+0.000V
8+0.000V
9
10
11
12
13
14
15
16
0
0
0
0
0
0
0
0
9
10
11
12
13
14
15
16
0000H
0000H
0000H
0000H
0000H
0000H
0000H
0000H
9+0.000V
10+0.00V
11+0.00V
12+0.00V
13+0.00V
14+0.00V
15+0.00V
16+0.00V
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16DAL-1 Current Analog Output
The P2-16DAL-1 Low Resolution Current Analog Output Module provides sixteen
channels of 4–20mA sourcing output signals for use with Productivity2000 system.
C
UL
R
US
Output Specifications
Output Channels
16
Module Signal Output Range
4–20mA Sourcing
Signal Resolution
Resolution Value of LSB
(least significant bit)
Data Range
12-bit
4–20mA = 3.9 μA / count
1 LSB = 1 count
0 to 4095 counts
Output Type (sourcing)
Current: 20mA max
Output Value in Fault Mode
Less than 4mA
Load Impedance
0–570Ω (19.2 VDC),
0–690Ω (21.6 VDC),
0–810Ω (24VDC),
0–930Ω (26.4 VDC),
0–1100Ω (30VDC)
Minimum Load: 0Ω @ 0–45°C
125Ω @ 45–60°C ambient temperature
Maximum Inductive Load
1mH
Allowed Load Type
Grounded
Maximum Inaccuracy
Maximum Full Scale Calibration Error
(Including Offset)
Maximum Offset Calibration Error
1% of range (including temperature drift)
4-20mA ANALOG OUT
Accuracy vs. Temperature
Max Crosstalk at DC, 50/60Hz
±0.2% of range minimum
±0.2% of range maximum
±75 PPM / °C maximum full-scale
calibration change
(±0.005% of range / °C)
Output Stability and Repeatability
-72dB, 1 LSB
±4 LSB max., (±0.1% of full scale)
Monotonic with no missing codes
±2 count after 10 min. warm up (typical)
Output Ripple
±0.1% of full scale
Output Settling Time
0.3 ms max., 5µ min. (full scale range)
All Channel Update Rate
1ms
Maximum Continuous Overload
Outputs open circuit protected
Electronically current limited to 20mA
or less
Linearity Error (End to End)
Type of Output Protection
Output Signal at Power Up and Power
Down
External DC Power Required
4mA
24VDC @ 380mA
(Loop Power Included)
We recommend using pre-wired ZIPLink cables and
connection modules. See Chapter 5.
Module connector type is a 24-pin Molex Style
43025-2400.
2000
Hardware User Manual, 1st Edition, Rev. B
3–99
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16DAL-1 Current Analog Output (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation
1800VAC applied for 1 second
Insulation Resistance
>10MΩ @ 500VDC
Heat Dissipation
10000mW (Loop Power Included)
Enclosure Type
Open Equipment
Module Keying to
Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
EU Directive
Use ZIPLink Wiring System ONLY. See
“Wiring Options” in Chapter 5. Must use
copper conductors 75ºC or equivalent.
See the “EU Directive” topic in the
Productivity Suite Help File. Information can
also be obtained at:
www.productivity2000.com
Connector Type
24-Pin Molex Style 43025-2400
Weight
90g (3.2 oz)
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Agency Approvals
Connector Specifications
3–100
Connector Type
24-Pin Molex Style 43025-2400
Number of Pins
24
Pin Spacing
3x3 mm (0.118 x 0.118 in)
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16DAL-1 Current Analog Output (continued)
Wiring Diagrams
INTERNAL
MODULE
CIRCUITRY
ZL-RTB20
Labels
COM
COM
COM
COM
I1+
I5+
I2+
I6+
I3+
I7+
I4+
I8+
+V
+V
-V
-V
I9+
I13+
I10+
I14+
I11+
I15+
I12+
I16+
+
13
1
14
2
15
3
16
4
17
5
18
6
19
7
20
8
21
9
22
10
23
11
24
12
CH1 ADC
CH5 ADC
CH2 ADC
CH6 ADC
CH3 ADC
CH7 ADC
CH4 ADC
CH8 ADC
CH9 ADC
CH13 ADC
CH10 ADC
CH14 ADC
CH11 ADC
CH15 ADC
CH12 ADC
CH16 ADC
ISOLATED
ANALOG
CIRCUIT
POWE R
ISOLATED ANALOG
CIRCUIT COMMON
Current Sourcing Output Circuit
4 - 20mA
Load
Note: Shield is connected to common at the source device.
2000
Hardware User Manual, 1st Edition, Rev. B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
3–101
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16DAL-1 Current Analog Output (continued)
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-16DAL-1 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each output point
(channel selected and to each Status Bit Item.
A Stop Mode Value may also be assigned.
12
3–102
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16DAL-2 Voltage Analog Output
The P2-16DAL-2 Low Resolution Voltage Analog Output Module provides sixteen channels
of 0–10 VDC outputs for use with Productivity2000 system.
C
UL
R
US
Output Specifications
Output Channels
Module Signal Input Range
16
0–10V
Output Signal Resolution
Data Range
12-bit
0–10V = 2.44 mV per count
1 LSB = 1 count
0 to 4095 counts
Output Type
Voltage sourcing at 10mA max. (1 common)
Output Value in Fault Mode
0V
Output Impedance
0.2 Ω typical
Maximum Capacitive Load
0.01 µF maximum
Allowed Load Type
Grounded
Maximum Inaccuracy
Maximum Full Scale
Calibration Error
Maximum Offset Calibration Error
0.5% of range (including temperature drift)
Accuracy vs. Temperature
±75 PPM / °C maximum full-scale calibration
change (±0.0025% of range / °C)
Max Crosstalk at DC, 50/60Hz
-72dB, 1 LSB
Linearity Error (End to End)
±4 LSB maximum, (±0.1% of full scale)
Monotonic with no missing codes
Output Stability and Repeatability
±2% LSB after 10 min. warm up period
Output Ripple
±0.1% of full scale
Output Settling Time
300µs max., 5µ min. (full scale range)
All Channel Update Rate
1ms
Maximum Continuous Overload
Outputs current limited to 40mA typical;
Continuous overloads on multiple outputs
can damage the module.
Type of Output Protection
0.1 µF Transient Suppressor
External 24VDC Power Required
24VDC (-20% / + 25%), 265mA
Resolution Value of LSB
(least significant bit)
±0.2% of range maximum voltage
±0.2% of range maximum
We recommend using pre-wired ZIPLink cables and
connection modules. See Chapter 5.
Module connector type is a 24-pin Molex Style
43025-2400.
2000
Hardware User Manual, 1st Edition, Rev. B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
3–103
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-16DAL-2 Voltage Analog Output (continued)
General Specifications
Surrounding Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation
1800VAC applied for 1 second
Insulation Resistance
>10MΩ @ 500VDC
Heat Dissipation
8W
Enclosure Type
Open Equipment
Module Keying to Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Use ZIPLink Wiring System ONLY. See “Wiring
Options” in Chapter 5. Must use copper conductors
75ºC or equivalent.
EU Directive
See the “EU Directive” topic in the Productivity
Suite Help File. Information can also be obtained
at: www.productivity2000.com
Terminal Type
24-Pin Molex Style 43025-2400
Weight
100g (3.5 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
Connector Specifications
3–104
Connector Type
24-Pin Molex Style 43025-2400
Number of Pins
24
Pin Spacing
3x3 mm (0.118 x 0.118 in)
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-16DAL-2 Voltage Analog Output (continued)
Wiring Diagrams
INTERNAL
MODULE
INTERNAL
MODULE
CIRCUITRY
CIRCUITRY
COM
COM
COM
COM
COM
COM
COM
COM
V1+
V1+
V5+
V5+
V2+
V2+
V6+
V6+
V3+
V3+
V7+
V7+
V4+
V4+
V8+
V8+
+V+V
++
24VDC +/-10%
+V+V
24VDC +/-10%
-V
-V
-V
-V
V9+
V9+
V13+
V13+
V10+
V10+
V14+
V14+
V11+
V15+
V11+
V12+
V15+
ZL-RTB20
V16+
V12+
Labels
ZL-RTB20
V16+
1
13
1
13
2
14
2
14
CH1 ADC
CH1 ADC
CH5 ADC
CH5 ADC
CH2 ADC
CH2 ADC
CH6
ADC
CH6
ADC
CH3
ADC
CH3
ADC
CH7
ADC
CH7
ADC
CH4
ADC
CH4
ADC
CH8
ADC
CH8
ADC
3
15
15
3
16
16
44
17
17
55
18
18
66
19
19
77
20
8
21
9
22
10
23
11
24
12
8
20
CH9 ADC
CH9 ADC
CH13 ADC ISOLATED
CH13
ADC ISOLATED
CH10
ADC
ANALOG
CH10
ADC ANALOG
CH14
ADC
CIRCUIT
CH14
ADC
CH11
ADC
CIRCUIT
POWE
R
CH11
ADC
CH15
ADC
POWE R
CH12
ADC
CH15
ADC
CH16
ADC
CH12
ADC
9
21
10
22
11
23
CH16 ADC
12
24
Labels
ISOLATED ANALOG
CIRCUIT COMMON
ISOLATED ANALOG
CIRCUIT COMMON
Voltage Output Circuits
V+
V+
0 - 10
VDC Load
COM
±10 VDC
Load
COM
Load
Power Supply
AC or DC
Power Supply
V+
-10 - 0
VDC Load
COM
Load
Power Supply
2000
Hardware User Manual, 1st Edition, Rev. B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
3–105
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
c
D
P2-16DAL-2 Voltage Analog Output (continued)
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-16DAL-2 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each input point
(channel) selected and to each Status Bit Item.
3–106
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-8AD4DA-1 Current Analog Input/Output
The P2-8AD4DA-1 Current Analog Input/Output Module provides eight channels of
current sinking 0–20 mA inputs and four channels of current sourcing 4–20 mA outputs.
C
UL
R
US
Input Specifications
1I00.00
2I04.00
3I00.00
4I04.00
5I00.00
6I04.00
7I00.00
8I SPARE
Input Channels
8 (1 common)
Module Signal Input Range
0–20mA (Sinking)
Signal Resolution
12–16 bit, depending on input resolution
Input Resolution & Update Rate
(See Note 1)
Fine: 8ms, 0.305 μA, 16 bit
Medium: 2ms, 1.22 μA, 14 bit
Coarse: 700μs, 4.88 μA, 12 bit
Data Range
0–65535 counts
Input Type
Single Ended (1 common)
Maximum Continuous Overload
±31mA
Input Impedance
250Ω ±0.1%, 1/4 W
Hardware Filter Characteristics
Low pass 1st order, -3dB @ 48Hz
All Channel Update Rate
(See Note 2)
Fine 57ms
Medium: 17ms
Coarse: 7ms
Open Circuit Detection Time
Zero reading within 1s
Conversion Method
Successive approximation
Accuracy vs. Temperature
±15PPM/°C maximum
Maximum Inaccuracy
0.1% of range
Linearity Error (end to end)
0.015% of range maximum
Monotonic with no missing codes
Input Stability and Repeatability
±0.015% of range (after 10 minute warm-up)
Full Scale Calibration Error
(not including offset)
±0.05% of range maximum
Offset Calibration Error
±0.05% of range maximum
Maximum Crosstalk
-96dB ±1 -0.015% of full scale maximum
Recommended Fuse (external)
Edison S500-32-R, 0.032 A fuse
External DC Power Required
24VDC (-20% / +25%), 145mA
NOTE 1: The Input Resolution of Fine returns 16 bit resolution. Medium and Coarse are 14 and 12 bit
respectively. The 12 and 14 bit input values are scaled to 0–65535.
NOTE 2: Valid when all channels are set for the same Input Resolution.
We recommend using pre-wired ZIPLink cables
and connection modules. See Chapter 5.
If you wish to hand-wire your module, removable
terminal blocks are sold separately. Order part
number P2-RTB or P2-RTB-1
2000
Hardware User Manual, 1st Edition, Rev. B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
3–107
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-8AD4DA-1 Current Analog Input/Output (continued)
Output Specifications
Output Channels
4 (1 common)
Module Signal Output Range
4–20mA Sourcing
Output Signal Resolution
16-bit
Resolution Value of LSB
(least significant bit)
0.244 μA / count
1 LSB = 1 count
Data Range
0–65535 counts
Output Type
Current sourcing: 20mA max
Output Value in Fault Mode
≤ 4mA
Load Impedance
(Minimum External Power Supply)
0–480Ω (19.2 VDC)
0–600Ω (21.6 VDC)
0–715Ω (24VDC)
0–840Ω (26.4 VDC)
0–1010Ω (30VDC)
Maximum Inductive Load
1mH
Allowed Load Type
Grounded
Maximum Inaccuracy
0.1% of range
Maximum Full Scale Calibration
Error (not including offset error)
±0.065% of full scale
Maximum Offset Calibration Error
Accuracy vs. Temperature
±0.065% of full scale
±15PPM/°C max full scale calibration change
(±0.0025% of range/°C)
Max Crosstalk
-96dB, 1 LSB
Linearity Error (End to End)
±0.015% of range maximum
Monotonic with no missing codes
Output Stability and Repeatability
±0.015% after 10 minute warm-up typical
Output Ripple
0.01% of full scale at 50/60 Hz
Rising Time 200μs
Falling Time 135μs
(full scale change)
Output Setting Time
All Channel Update Rate
3.55 ms
Maximum Continuous Overload
Outputs open circuit protected
Type of Output Protection
Electronically current limited to 20mA or less
Output Signal (power-up, -down)
≤4mA
Removable Terminal Block Specifications
Part Number
P2-RTB
P2-RTB-1
Number of positions
18 Screw Terminals
18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
Conductors
“USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver Width
1/8 in (3.8 mm) Maximum
Screw Size
M2
N/A
Screw Torque
2.5 lb·in (0.28 N·m)
N/A
3–108
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-8AD4DA-1 Current Analog Input/Output (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation
1800VAC applied for 1 second
Insulation Resistance
> 10MΩ @ 500VDC
Heat Dissipation
2.47 W
Enclosure Type
Open Equipment
Module Keying to Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Use ZIPLink Wiring System or removable
terminal block (not included). See “Wiring
Options” in Chapter 5.
EU Directive
See the “EU Directive” topic in the
Productivity Suite Help File. Information
can also be obtained at:
www.productivity2000.com
Connector Type (Not included)
18-position removable terminal block
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
2000
Hardware User Manual, 1st Edition, Rev. B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
3–109
Chapter 3: Analog I/O Specifications
Wiring Diagrams
Current Input Circuits
–
.032A
2-Wire 4-20 mA
Transmitter
+
+
–
+24VDC User
Supplied Power
2-Wire Transmitter
fuse
+
.032A
+
3-Wire Current
Transmitter
+
Input Channels
Output Channels
Note: Shield is connected to common at the source device.
-
+
CH6 ADC
CH7 ADC
9 10 11 12 13 14 15 16 17 18
4 - 20mA
Load
CH5 ADC
8
Current Output Circuits
CH4 ADC
7
Note: Do not connect both ends of shield.
CH3 ADC
6
4-Wire Transmitter
CH2 ADC
5
–
User Supplied
Transmitter Power
CH1 ADC
4
.032A
COM
I1+
I2+
I3+
I4+
I5+
I6+
I7+
I8+
COM
I1+
I2+
I3+
I4+
COM
COM
0V
24V+
3
fuse
2
+
–
+24VDC User
Supplied Power
3-Wire Transmitter
Load
Power Supply
INTERNAL
MODULE CIRCUITRY
COM
–
4-Wire 4-20 mA
Transmitter
An Edison S500-32-R
0.032 A fast-acting fuse
is recommended for all
4-20 mA current loops.
fuse
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-8AD4DA-1 Current Analog Input/Output (continued)
CH8 ADC
CH1 DAC
CH2 DAC
CH3 DAC
CH4 DAC
ISOLATED ANALOG
CIRCUIT POWER
24 VDC User
Supplied Power
ISOLATED ANALOG
CIRCUIT COMMON
Note: This module includes input and output channels. Before connecting
field wiring, verify that you are connecting to the appropriate terminals
3–110
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-8AD4DA-1 Current Analog Input/Output (continued)
Module Configuration
Using the Hardware Configuration tool in the Productivity Suite
programming software, drag and drop the P2-8AD4DA-1 module into
the base configuration.
Select Automatic Module Verification or No Verification and Enable Hot
Swap. Also specify Input Resolution for inputs and Stop Mode Value for
outputs. If desired, assign a User Tagname to each input and output
point (channel) selected and to each Status Bit Item.
2000
Hardware User Manual, 1st Edition, Rev. B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
3–111
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-8AD4DA-1 Current Analog Input/Output (continued)
OLED Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
Hold SEL button down to cycle through primary screens. Release button to select screen.
DISPLAY
SETUP
INFO
DISPLAY
STATUS
INFO
DISPLAY
UNITS
DECIMAL
COUNTS
DISPLAY
UNITS
HEX
COUNTS
DISPLAY
UNITS
mA
These screens will
then auto cycle
P28AD4DA-1
Fw. Rev.
1.00
In:
0-20mA
Out:
4-20mA
Channels
Enabled:
7
Fault Messages – Appear
in place of data during a
fault condition.
3–112
This screen will
auto cycle with
status information
End of
Status
Menu
List
Momentarily Press
1I 00000
SEL button to
2I 00000
toggle through
3I 00000
secondary displays
4I 00000
Error Messages – An existing error will
be inserted into the cycling Status Info screen
MISSING
EXTERNAL
24VDC
SELFTEST
FAIL
REPLACE
MODULE
End of
Status
Menu
List
MISSING
CONFIG
DATA
On if input is
greater than or
equal to 20 mA.
1I OVER
2I UNDER
3I
4I
On if input is
less than or
equal to 0 mA.
2000
1I
2I
3I
4I
0000H
0000H
0000H
0000H
1I00.0mA
2I00.0mA
3I00.0mA
4I00.0mA
5I
6I
7I
8I
00000
00000
00000
SPARE
5I
6I
7I
8I
0000H
0000H
0000H
SPARE
5I00.0mA
6I00.0mA
7I00.0mA
8I SPARE
1I
2I
3I
4I
5I
6I
7I
8I
00000
00000
00000
00000
00000
00000
00000
SPARE
1I
2I
3I
4I
5I
6I
7I
8I
0000H
0000H
0000H
0000H
0000H
0000H
0000H
SPARE
1I04.0mA
2I04.0mA
3I04.0mA
4I04.0mA
5I04.0mA
6I04.0mA
7I04.0mA
8I SPARE
1O
2O
3O
4O
00000
00000
00000
00000
1O
2O
3O
4O
0000H
0000H
0000H
0000H
1O04.0mA
2O04.0mA
3O04.0mA
4O04.0mA
Note: SPARE denotes deselected channel
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-8AD4DA-2 Voltage Analog Input/Output
The P2-8AD4DA-2 Voltage Analog Input/Output Module provides eight channels of
0–10 VDC inputs and four channels of 0–10 VDC outputs.
C
UL
R
US
Input Specifications
1I00.00V
2I00.00V
3I00.00V
4I00.00V
5I00.00V
6I00.00V
7I00.00V
8I SPARE
Input Channels
8 inputs (1 common)
Input Ranges
0–5 VDC, 0–10 VDC
Signal Resolution
12–16 bit, depending on input resolution
0–5V Input Resolution & Update
Rate (See Note 1)
Fine: 7.1 ms, 76μV, 16 bit
Medium: 1.78 ms, 305μV, 14 bit
Coarse: 444μs, 1.22 mV, 12 bit
0–10V Input Resolution & Update
Rate (See Note 1)
Fine: 7.1 ms, 152μV, 16 bit
Medium: 1.78 ms, 610μV, 14 bit
Coarse: 444μs, 2.44 mV, 12 bit
Data Range
0–65535 counts
Maximum Continuous Overload
±100V, voltage input
Input Impedance
1MΩ (±10%) voltage input
Hardware Filter Characteristics
Low pass 1st order, -3dB @ 80Hz
All Channel Update Rate
(See Note 2)
Fine 56.8 ms
Medium: 14.24 ms
Coarse: 3.55 ms
Conversion Method
Successive approximation
Accuracy vs. Temperature
±15PPM/°C maximum
Maximum Inaccuracy
0.1% of range
Linearity Error (end to end)
±0.015% of range maximum
Monotonic with no missing codes
Input Stability and Repeatability
±0.025% of range
(after 10 minute warm-up)
Full Scale Calibration Error
(not including offset)
±0.05% of range maximum
Offset Calibration Error
±0.05% of range maximum
Maximum Crosstalk
-96dB, 1LSB
External DC Power Required
24VDC (-20% / +25%), 130mA
NOTE 1: The Input Resolution of Fine returns 16 bit resolution. Medium and Coarse are 14 and 12
bit respectively. The 12 and 14 bit input values are scaled to 0–65535.
NOTE 2: Valid when all channels are set for the same Input Resolution.
We recommend using pre-wired ZIPLink cables
and connection modules. See Chapter 5.
If you wish to hand-wire your module, removable
terminal blocks are sold separately. Order part
number P2-RTB or P2-RTB-1
2000
Hardware User Manual, 1st Edition, Rev. B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
3–113
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-8AD4DA-2 Voltage Analog Input/Output (continued)
Output Specifications
Output Channels
4 (1 common)
Module Signal Output Range
0–10 VDC, 0–5 VDC
Output Signal Resolution
16-bit
Resolution Value of LSB
(least significant bit)
0–5V = 76μV/count
0–10V = 152μV/count
1 LSB = 1 count
Data Range
0–65535 counts
Output Type
Voltage sourcing/sinking at 10mA maximum
Output Value in Fault Mode
0V
Load Impedance
≥1.5 kΩ
Maximum Capacitive Load
0.01 μF
Allowed Load Type
Grounded
Maximum Inaccuracy
0.1% of range
Maximum Full Scale Calibration
Error (not including offset error)
±0.065% of range maximum
Maximum Offset Calibration Error
±0.065% of range maximum
Accuracy vs. Temperature
±25PPM/°C max full scale calibration change
(±0.0025% of range/°C)
Max Crosstalk
-96dB, 1 LSB
Linearity Error (End to End)
±0.015% of full scale
Monotonic with no missing codes
Output Stability and Repeatability
±0.015% after 10 minute warm-up typical
Output Ripple
0.01% of full scale at 50/60 Hz
Output Setting Time
500μs max, 5μs min (full scale change)
All Channel Update Rate
5ms
Maximum Continuous Overload
Outputs current limited to 15mA typical
Type of Output Protection
15VDC peak output voltage
Output Signal (power-up, -down)
0V
Removable Terminal Block Specifications
Part Number
3–114
P2-RTB
P2-RTB-1
Number of positions
18 Screw Terminals
18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
Conductors
“USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver Width
1/8 in (3.8 mm) Maximum
Screw Size
M2
N/A
Screw Torque
2.5 lb·in (0.28 N·m)
N/A
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-8AD4DA-2 Voltage Analog Input/Output (continued)
General Specifications
Operating Temperature
0º to 60ºC (32º to 140ºF)
Storage Temperature
-20º to 70ºC (-4º to 158ºF)
Humidity
5 to 95% (non-condensing)
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation
1800VAC applied for 1 second
Insulation Resistance
>10MΩ @ 500VDC
Heat Dissipation
1.95 W
Enclosure Type
Open Equipment
Module Keying to
Backplane
Electronic
Module Location
Any I/O slot in a Productivity2000 System
Field Wiring
Use ZIPLink Wiring System or removable terminal block
(not included). See “Wiring Options” in Chapter 5.
EU Directive
See the “EU Directive” topic in the Productivity Suite
Help File. Information can also be obtained at:
www.productivity2000.com
Connector Type (not
included)
18-position removable terminal block
Weight
90g (3.2 oz)
Agency Approvals
UL508 File E139594, Canada & USA
CE (EN61131-2*)
* Meets EMC and Safety requirements. See the D.O.C. for details.
2000
Hardware User Manual, 1st Edition, Rev. B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
3–115
Chapter 3: Analog I/O Specifications
Wiring Diagrams
5
CH4 ADC
6
CH5 ADC
7
CH6 ADC
8
CH7 ADC
9 10 11 12 13 14 15 16 17 18
OUTPUT CHANNELS
4
CH3 ADC
CH8 ADC
Voltage Input Circuits
CH1 DAC
CH2 DAC
CH3 DAC
V+
4-Wire Voltage
Transmitter
AC or DC
COM
Transmitter
Power Supply
4-Wire Transmitter
CH4 DAC
3-Wire Voltage
Transmitter
+
V+
–
COM
+
ISOLATED ANALOG
CIRCUIT POWER
3-Wire Transmitter
ISOLATED ANALOG
CIRCUIT COMMON
+
CH2 ADC
-
CH1 ADC
3
COM
V1+
V2+
V3+
V4+
V5+
V6+
V7+
V8+
COM
V1+
V2+
V3+
V4+
COM
COM
0V
24V+
2
INPUT CHANNELS
INTERNAL
MODULE CIRCUITRY
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-8AD4DA-2 Voltage Analog Input/Output (continued)
24 VDC User
Supplied Power
Voltage Output Circuits
V+
0-5 VDC
Load
COM
0-10 VDC
Load
COM
V+
NOTE: This module includes input and output
channels. Before connecting field wiring, verify that
you are connecting to the appropriate terminals.
3–116
2000
Hardware User Manual, 1st Edition, Rev. B
Chapter 3: Analog I/O Specifications
P2-8AD4DA-2 Voltage Analog Input/Output (continued)
Module Configuration
Using the Hardware Configuration tool in the Productivity Suite
programming software, drag and drop the P2-8AD4DA-2 module into
the base configuration.
Select Automatic Module Verification or No Verification and Enable Hot
Swap. Also specify Input Range and Input Resolution for inputs along
with Output Range and Stop Mode Value for outputs. If desired, assign
a User Tagname to each input and output point (channel) selected and
to each Status Bit Item.
2000
Hardware User Manual, 1st Edition, Rev. B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
3–117
Chapter 3: Analog I/O Specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
P2-8AD4DA-2 Voltage Analog Input/Output (continued)
OLED Panel Display
Power On
PASSED
SELF
TEST
Appears
initially
Hold SEL button down to cycle through primary screens. Release button to select screen.
DISPLAY
SETUP
INFO
DISPLAY
STATUS
INFO
DISPLAY
UNITS
DECIMAL
COUNTS
DISPLAY
UNITS
HEX
COUNTS
DISPLAY
UNITS
VOLTS
These screens will
then auto cycle
P28AD4DA-2
Fw. Rev.
1.00
In:
0-5/10V
Out:
0-5/10V
Channels
Enabled:
7
Fault Messages – Appear
in place of data during a
fault condition.
3–118
This screen will
auto cycle with
status information
End of
Status
Menu
List
Momentarily Press
1I 00000
SEL button to
2I 00000
toggle through
3I 00000
secondary displays
4I 00000
Error Messages – An existing error will
be inserted into the cycling Status Info screen
MISSING
EXTERNAL
24VDC
SELFTEST
FAIL
REPLACE
MODULE
End of
Status
Menu
List
MISSING
CONFIG
DATA
Input signal is OVER
the maximum detectable
by the module.
1I OVER
2I UNDER
3I
4I
Input signal = 0(Voltage)
1I
2I
3I
4I
0000H
0000H
0000H
0000H
1I00.00V
2I00.00V
3I00.00V
4I00.00V
5I
6I
7I
8I
00000
00000
00000
SPARE
5I
6I
7I
8I
0000H
0000H
0000H
SPARE
5I00.00V
6I00.00V
7I00.00V
8I SPARE
1I
2I
3I
4I
5I
6I
7I
8I
00000
00000
00000
00000
00000
00000
00000
SPARE
1I
2I
3I
4I
5I
6I
7I
8I
0000H
0000H
0000H
0000H
0000H
0000H
0000H
SPARE
1I00.00V
2I00.00V
3I00.00V
4I00.00V
5I00.00V
6I00.00V
7I00.00V
8I SPARE
1O
2O
3O
4O
00000
00000
00000
00000
1O
2O
3O
4O
0000H
0000H
0000H
0000H
1O00.00V
2O00.00V
3O00.00V
4O00.00V
Note: SPARE denotes deselected channel
2000
Hardware User Manual, 1st Edition, Rev. B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising