Onkyo DV-S939 Operating Instructions Manual user guide

Onkyo DV-S939 Operating Instructions Manual user guide
Contents
Before Using Your DVD Player
2
DVD AUDIO/VIDEO Player
Getting Started
8
DV-S939
Basic Playback
20
Advanced Playback
27
Quick Control and
Performance Options
36
Function Setup
44
Remote Controller
56
Others
61
Instruction Manual
Thank you for purchasing the Onkyo DVD AUDIO/
VIDEO Player.
Please read this manual thoroughly before making
connections and turning on the power.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new Player.
Please retain this manual for future reference.
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)Cover.p65
1
10/2/00, 3:23 PM
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING
AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
Important Safeguards
1.
Read Instructions – All the safety and operating instructions should
be read before the appliance is operated.
2.
Retain Instructions – The safety and operating instructions should
be retained for future reference.
3.
Heed Warnings – All warnings on the appliance and in the operating
instructions should be adhered to.
4.
Follow Instructions – All operating and use instructions should be
followed.
5.
Cleaning – Unplug the appliance from the wall outlet before
cleaning. The appliance should be cleaned only as recommended by
the manufacturer.
6.
Attachments – Do not use attachments not recommended by the
appliance manufacturer as they may cause hazards.
7.
Water and Moisture – Do not use the appliance near water –for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming pool; and the like.
8.
9.
Accessories – Do not place the appliance on an unstable cart, stand,
tripod, bracket, or table. The appliance may fall, causing serious injury
to a child or adult, and serious damage to the appliance. Use only with
a cart, stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the appliance. Any mounting of the
appliance should follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the manufacturer.
An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
PORTABLE CART WARNING
14. Lightning – For added protection for the appliance during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the appliance due to
lightning and power-line surges.
15. Overloading – Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of fire or
electric shock.
16. Object and Liquid Entry – Never push objects of any kind into the
appliance through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the appliance.
17. Servicing – Do not attempt to service the appliance yourself as
opening or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.
18. Damage Requiring Service – Unplug the appliance form the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen into the appliance,
C. If the appliance has been exposed to rain or water,
D. If the appliance does not operate normally by following the
operating instructions. Adjust only those controls that are covered
by the operating instructions as an improper adjustment of other
controls may result in damage and will often require extensive
work by a qualified technician to restore the appliance to its
normal operation,
E. If the appliance has been dropped or damaged in any way, and
F. When the appliance exhibits a distinct change in performance –
this indicates a need for service.
S3125A
10. Ventilation – Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the appliance and to
protect it from overheating, and these openings must not be blocked or
covered. The openings should never be blocked by placing the
appliance on a bed, sofa, rug, or other similar surface. The appliance
should not be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided. There should be free space
of at least 5 cm (2 in.) and an opening behind the appliance.
11. Power Sources – The appliance should be operated only from the
type of power source indicated on the marking label. If you are not
sure of the type of power supply to your home, consult your appliance
dealer or local power company.
19. Replacement Parts – When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
20. Safety Check – Upon completion of any service or repairs to the
appliance, ask the service technician to perform safety checks to
determine that the appliance is in proper operation condition.
21. Wall or Ceiling Mounting – The appliance should be mounted to a
wall or ceiling only as recommended by the manufacturer.
22. Heat – The appliance should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
12. Grounding or Polarization – The appliance may be equipped with
a polarized alternating current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the polarized plug.
2
13. Power-Cord Protection – Power-supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the
appliance.
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p02-07.p65
2
10/2/00, 3:23 PM
Precautions
This unit contains a semiconductor laser system and is classified as a
“CLASS 1 LASER PRODUCT”. So, to use this model properly, read
this Instruction Manual carefully. In case of any trouble, please contact
the store where you purchased the unit. To prevent being exposed to the
laser beam, do not try to open the enclosure.
The label on the right is
applied on the rear
panel except for USA
and Canadian models.
“CLASS 1 LASER
PRODUCT ”
CAUTION:
VISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK
FAILED OR DEFEATED. DO NOT STARE INTO BEAM.
CAUTION:
1. This unit is a CLASS 1 LASER PRODUCT and employs a laser
inside the cabinet.
2. To prevent the laser from being exposed, do not remove the
cover. Refer servicing to qualified personnel.
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
For U.S. model
For Canadian model
The laser is covered by a housing which prevents exposure during
operation or maintenance. However, this product is classified as a Laser
Product by CDRH (Center for Devices and Radiological Health) which is a
department of the Food and Drug Administration. According to their
regulations 21 CFR section 1002.30, all manufactures who sell Laser
Products must maintain records of written communications between the
manufacturer, dealers and customers concerning radiation safety. If you
have any complaints about instructions or explanations affecting the use of
this product, please feel free to write to the address on the back page of this
manual. When you write us, please include the model number and serial
number of your unit.
This class B digital apparatus complies with Canadian ICES-003.
In compliance with Federal Regulations, the certification, identification
and the period of manufacture are indicated on the rear panel.
FCC INFORMATION FOR USER
CAUTION:
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT, FULLY INSERT.
Modele pour les Canadien
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
Sur les modeles dont la fiche est polarisee:
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU
FOND.
The user changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
3
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p02-07.p65
3
10/2/00, 3:23 PM
Precautions
1. Regional Restriction Codes (Region Number)
Regional restriction codes are built into DVD Players and DVD-Video
media for each sales region. If the regional code of the DVD Player
does not match one of the regional codes on the DVD-Video, playback
is not possible.
The regional number can be found on the rear panel of the DVD
Player. (e.g.
1
for Region 1)
2. About This Manual
This manual explains the basic procedures for operating the DVD
Player. Some DVD-Video and DVD-Audio discs do not support the
full potential of the DVD technology. Your DVD Player may therefore
not respond to all operating commands. Refer to instruction notes on
discs.
A “ ” mark may appear on the TV screen during operation. It means
that the operation is not permitted by the DVD Player or the disc.
3. Warranty Claim
You can find the serial number on the rear panel of the unit. In case of
warranty claim, please report this number.
4. Recording Copyright
Recording of copyrighted material for other than personal use is illegal
without permission of the copyright holder.
5. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ
THE FOLLOWING SECTION CAREFULLY.
The voltage of the available power supply differs according to country
or region. Be sure that the power supply voltage of the area where the
unit will be used meets the required voltage (e.g., AC 120 V, 60 Hz)
written on the rear panel.
6. Do not touch the unit with wet hands
Do not handle the unit or power cord when your hands are wet or
damp. If water or any other liquid enters the case, take the unit to an
authorized service center for inspection.
7. Location of the unit
• Place the unit in a well-ventilated location.
Take special care to provide plenty of ventilation on all sides of the
unit especially when it is placed in an audio rack. If ventilation is
blocked, the unit may overheat and malfunction.
• Do not expose the unit to direct sunlight or heating units as the unit’s
internal temperature may rise and shorten the life of the pickup.
• Avoid damp and dusty places and places directly affected by
vibrations from the speakers. In particular, avoid placing the unit on
or above one of the speakers.
• Be sure the unit is placed in a horizontal position. Never place it on
its side or on a slanted surface as it may malfunction.
• When you place the unit near a TV, radio, or VCR, the playback
picture may become poor and the sound may be distorted. In this
case, place the unit away from the TV, radio, or VCR.
9. Notes on Handling
• When shipping the unit, use the original shipping carton and
packing materials. For maximum protection, repack the unit as it
was originally packed at the factory.
• Do not use volatile liquids, such as insect spray, near the unit. Do
not leave rubber or plastic products in contact with the unit for a
long time. They will leave marks on the finish.
• The top and rear panels of the unit may become warm after a
long period of use. This is not a malfunction.
• When the unit is not in use, be sure to remove the disc and turn off
the power.
• If you do not use the unit for a long period, the unit may not
function properly in the future. Turn on and use the unit
occasionally.
10. To Obtain a Clear Picture
The unit is a high technology, precision device. If the optical pick-up
lens and disc drive parts are dirty or worn down, the picture quality
becomes poor. To obtain a clear picture, we recommend regular
inspection and maintenance (cleaning or parts replacement) every
1,000 hours of use depending on the operating environment. For
details, contact your nearest dealer.
11. Notes on Moisture Condensation
Moisture condensation damages the unit.
Please read the following carefully.
• What is moisture condensation?
Moisture condensation occurs, for example, when you pour a cold
drink into a glass on a warm day. Drops of water form on the outside
of the glass. In the same way, moisture may condense on the optical
pick-up lens inside the unit, one of the most crucial internal parts of
the unit.
• Moisture condensation occurs in the following cases.
– When you bring the unit directly from a cold place to a warm
place.
– When you use the unit in a room where you just turned on the
heater, or a place where the cold wind from the air conditioner
directly hits the unit.
– In summer, when you use the unit in a hot and humid place just
after you move the unit from an air conditioned room.
– When you use the unit in a humid place.
• Do not use the unit when moisture condensation may
occur.
If you use the unit in such a situation, it may damage discs and
internal parts. Remove the disc, connect the power cord of the unit
to the wall outlet, turn on the unit, and leave it for two or three
hours. After a few hours, the unit will have warmed up and
evaporated any moisture. Keep the unit connected to the wall outlet
and moisture condensation will seldom occur.
8. Care
From time to time you should wipe the front and rear panels and the
cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a
weak solution of mild detergent and water, wring it out dry, and wipe
off the dirt. Following this, dry immediately with a clean cloth.
Do not use rough material, thinners, alcohol or other chemical solvents
or cloths since these could damage the finish or remove the panel
lettering.
4
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p02-07.p65
4
10/2/00, 3:23 PM
Table of Contents
Important Safeguards/Precautions/Table of Contents/Notes on Discs ............ 2 - 6
Getting Started
Features/Supplied Accessories ............................................................................. 8
Preparing the Remote Controller .......................................................................... 9
Making Connections ........................................................................................... 10
Control Position and Names ............................................................................... 14
Connecting the Power/Turning on the DVD Player ............................................. 17
Setting up the DVD Player for Optimal Performance .......................................... 18
Basic Playback
Playing DVD-Video/Audio, Video CD, and CD .................................................... 20
Locating a Specific Title/Chapter/Track/Location ................................................ 24
Advanced Playback
Playing Repeatedly ............................................................................................. 27
Playing in a Favorite Order ................................................................................. 28
Playing in Random Order .................................................................................... 29
Zooming a Picture ............................................................................................... 30
Improving Picture Quality .................................................................................... 31
Selecting the Camera Angle ............................................................................... 32
Selecting the Subtitle Language/Turning On/Off Subtitles .................................. 33
Selecting the Audio Language ............................................................................ 34
Output Sound Conversion Table ......................................................................... 35
Quick Control and Performance Options
Using the Graphic Remote Control - V.REMOTE ............................................... 36
Selecting the Playback Function - QUICK .......................................................... 37
Accessing Playback Features - NAVI .................................................................. 38
Selecting Progressive Video Output ................................................................... 42
Turning Off the Video Signal Output ................................................................... 43
Function Setup
Customizing the Function Settings ..................................................................... 44
Table of Languages ............................................................................................. 55
Remote Controller
Using the Remote Controller ............................................................................... 56
Programming the Commands of Other Remote Controller Units
into the Remote Controller ........................................................................... 58
Others
Troubleshooting .................................................................................................. 61
Specifications ...................................................................................................... 62
5
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p02-07.p65
5
10/2/00, 3:23 PM
Notes on Discs
This section shows you how to handle, clean, and store discs.
Playable Discs
Handling Discs
• Do not touch the playback side of the disc.
This DVD Player can playback the following discs.
Disc mark
DVDVideo
Contents
Disc size
Audio
+
Video
(moving
pictures)
12 cm
Playback side
• Do not attach paper or tape to discs.
8 cm
12 cm
DVDAudio
Cleaning Discs
Audio
8 cm
Video
CD
Audio +
Video
(moving
pictures)
CD
Audio
• Fingerprints and dust on the disc cause picture and sound
deterioration. Wipe the disc from the center outwards with a soft
cloth. Always keep the disc clean.
12 cm
8 cm
12 cm
8 cm (CD single)
• CD-R and CD-RW discs recorded by CD-DA method can also be
played. Some CD-R/RW discs may be incompatible.
• You cannot playback discs other than those listed above.
• You cannot play discs such as CD-ROM, DVD-RAM, DVD-RW,
etc., even if the marks in the above table are labeled on those
discs.
• This DVD Player uses the PAL*/NTSC color system, and cannot
playback video media recorded in any other color system
(SECAM, etc.).
• Avoid using heart-shaped or octagonal discs. Playing irregularly
shaped discs may damage the internal mechanism of the DVD
Player.
Discs with shapes such
as these cannot be
played.
• If you cannot wipe off the dust with a soft cloth, wipe the disc
lightly with a slightly moistened soft cloth and finish with a dry
cloth.
• Do not use any type of solvent such as thinner, benzine,
commercially available cleaners or antistatic spray for vinyl LPs.
It may damage the disc.
Storing Discs
• Do not store discs in a place subject to direct sunlight or near heat
sources.
• Do not store discs in places subject to moisture and dust such as a
bathroom or near a humidifier.
• Store discs vertically in a case. Stacking or placing objects on
discs outside of their case may cause warping.
• Do not use discs that have residue from adhesive tape, rental discs
that have peeling labels, or discs that have custom labels or
stickers. Otherwise, you may not be able to eject the discs or the
DVD Player may become inoperative.
* PAL is not applicable for USA and Canadian models
6
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p02-07.p65
6
10/2/00, 3:23 PM
About Video CDs
This DVD Player supports Video CDs equipped with the PBC
(Version 2.0) function. (PBC is the abbreviation of Playback
Control.) You can enjoy two playback variations depending on the
type of disc.
• Video CD not equipped with PBC function (Version 1.1)
Sound and movies can be played on this DVD Player in the same
way as a CD.
• Video CD equipped with PBC function (Version 2.0)
In addition to operation of the Video CD not equipped with the
PBC function, you can enjoy playback with interactive software
and search function using the menu displayed on the TV screen
(Menu Playback). Some of the functions described in this
Instruction Manual may not work with some discs.
Notes on Copyright
The Structure of the Disc Content
DVD-Video
Normally, the contents of DVD-Video are divided into titles, and the
titles are subdivided into chapters.
Title 1
Chapter 1 Chapter 2
DVD-Audio
The contents of DVD-Audio are divided into groups, and the groups
are subdivided into tracks.
Group 2
Group 1
Track 1
It is forbidden by law to copy, broadcast, show, broadcast on cable,
play in public, and rent copyrighted material without permission.
The video recorded on DVD-Video is copy protected, and any
recordings made from these discs will be distorted.
This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
Title 2
Chapter 1 Chapter 2 Chapter 3
Track 1
Track 2
Track 2
Track 3
Video CD/CD
Video CD and CD are divided into tracks.
Track 1
Track 2
Track 3
Track 4
Track 5
7
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p02-07.p65
7
10/2/00, 3:23 PM
Features/Supplied Accessories
Features
THX*1 Ultra Certified
Plays DVD-Audio & Video Discs, Video CDs, CD-Rs & CDs
54 MHz/10-bit Video DAC
192 kHz/24-bit DACs
DB-25 and RCA-6ch Multichannel Outputs
2 Gold-Plated Progressive Component-Video Outputs
4 Digital Outputs pass DTS®*2, Dolby®*3 Digital and PCM Signals
Dolby® Digital decoder Built In
Separate Transformers for Digital and Analog Sections
Electrical and Magnetic Shielded Mechanism
Heavy-Duty Mechanical Tray Door
Full-function remote controller with “Learning” function for control
of other component
*1 Manufactured under licence from Lucasfilm Ltd. Lucasfilm and
THX are registered trademarks of Lucasfilm Ltd.
*2 Manufactured under license from Digital Theater Systems, Inc.
US Pat. No.5,451,942 and other worldwide patents issues and
pending, “DTS” and “DTS Digital Surround” are trademarks of
Digital Theater Systems, Inc. ©1996 Digital Theater Systems,
Inc. All Rights reserved.
*3 Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks
of Dolby Laboratories. Confidential Unpublished Works.
©1992-1997 Dolby Laboratories, Inc. All rights reserved.
THX Ultra
Before any home theatre component can be THX Ultra certified, it
must pass a rigorous series of quality and performance tests. Only
then can product feature the THX Ultra logo, which is your
guarantee that the Home Theatre products you purchase will give
you superb performance for many years to come.
Supplied Accessories
Make sure your box contains everything listed below.
If any pieces are missing, contact your nearest Onkyo dealer.
The number of accessories is indicated in brackets [ ].
Power cord [1]
Remote controller (RC-438DV) [1]
Audio/video connection cable [1]
Batteries (size AA/UM-3) [2]
S-video cable [1]
DB-25 cable [1]
8
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p08-09.p65
8
10/2/00, 3:23 PM
Preparing the Remote Controller
Inserting the Batteries
Open the battery compartment cover.
Using the Remote Controller
Point the remote controller toward the remote control sensor.
(1
6
30˚
Ab
ou
t5
m
30˚
fe
e
t)
Remote control sensor
Insert the two R6 (size AA) batteries.
Be sure to match the + and – ends of the batteries
with the diagram inside the battery compartment.
Notes
Close the battery compartment cover.
• Place the unit away from strong light such as direct sunlight or inverted
fluorescent light which can prevent proper operation of the remote
controller.
• Using another remote controller of the same type in the same room or using
the unit near equipment which uses infrared rays may cause operational
interference.
• Do not put any object such as a book on the remote controller. The buttons
of the remote controller may be pressed by mistake and drain the batteries.
• Make sure the audio rack doors do not have colored glass. Placing the unit
behind such doors may prevent proper remote controller operation.
• If there is any obstacle between the remote controller and the remote
control sensor, the remote controller will not operate.
Notes
• Do not mix new batteries with old batteries or different kinds of
batteries.
• To avoid corrosion, remove the batteries if the remote controller
is not to be used for a long time.
• Remove dead batteries immediately to avoid damage from
corrosion. If the remote controller does not operate smoothly,
replace both batteries at the same time.
• The life of the batteries supplied is about six months but this
will vary depending on usage.
9
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p08-09.p65
9
10/2/00, 3:23 PM
Making Connections
To accommodate a wide range of home entertainment systems, this player features numerous connection types for both audio and video. Please
refer to the instructions on this and the following pages to determine the best possible type of connections for your system.
Before Connecting
• Refer to the instruction manuals supplied with any and all components that
you plan to connect the DVD Player to.
• Be sure to turn off the power of all components to be connected and unplug
them from the wall outlet before making any connections.
• Connect the DVD Player to the TV directly. If you connect the DVD Player
to a VCR, TV/VCR combination, or video selector, the playback picture may
be distorted as DVD Video images are copy protected.
• Please note that video connections to a TV or monitor are necessary because
some discs require on-screen menu interaction before they can be played.
• Connect the plugs securely.
Incomplete
Inserted completely
Connections to a TV
MULTI CHANNEL OUTPUT
The diagram below shows how to make connections to a TV with built-in stereo speakers using the supplied audio/video cable. After making the
connections on this page, you will be able to start using the DVD Player.
ANALOG OUTPUT
CENTER
SURR
FRONT
CH 1
CH 2
DIGITAL OUTPUT
L
DO NOT connect the
power cord until all
connections are
complete.
AC INLET
R
SUBWOOFER
COAXIAL
COMPONENT
Y
PB
S VIDEO
OPTICAL
CH 1
COAXIAL
OPTICAL
CH 2
VIDEO
PR
RS 232
CH 1
CH 2
VIDEO OUTPUT
Be sure to match the colors of the plugs on the cable with the corresponding
jacks on the DVD Player and the TV: yellow for video, red for R (right)
audio and white for L (left) audio.
L (White)
Note
R (Red)
Using the supplied audio/video cable, make audio connections from
the ANALOG OUTPUT CH1 or CH2 L and R jacks to the
corresponding audio input jacks on the TV. In the same manner,
make video connection from the VIDEO OUTPUT VIDEO CH1 or
CH2 jack to the corresponding video input jack on the TV.
Be sure to set Audio Out Select to “Analog 2Ch” using the onscreen menu explained in “Customizing the Function Settings”
starting on page 44. See page 48 for direct information.
(Yellow)
Using the supplied audio/video connection
cable
: Signal flow
If the TV audio input is monaural, leave the
red plug disconnected.
Audio/video cable (supplied)
To audio inputs
L (White)
R (Red)
To video input (Yellow)
10
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p10-19.p65
10
10/2/00, 3:23 PM
Optional Video Connections
Visible improvements in DVD-Video quality can be achieved by making either S-video or component video connections to a TV or monitor
compatible with these types of connections.
Note
When either S-video or component video connection is made, it is not necessary to make composite video connections using the yellow cord of the audio-video
cable.
Making component video connections
If the TV or monitor has component video inputs, making this type
of video connection will produce the ideal picture quality for the
presentation of DVD-Video. Using a componect video cable (sold
separately), connect the VIDEO OUTPUT COMPONENT CH1 or
CH2 jacks to the corresponding component video input jacks on the
TV.
Actual labels for component video inputs may vary depending on
the TV manufacturer. (e.g. Y, R-Y, B-Y or Y, CB, CR)
In some TVs or monitors, the color levels of the playback picture
may be reduced slightly or the tint may change. In such a case,
adjust the TV or monitor for optimum performance.
Be sure to set Audio Out Select to “Analog 2Ch” using the on-screen
menu explained in “Customizing the Function Settings” starting on
page 44. See page 48 for direct information.
PROGRESSIVE outputs/inputs
Some TVs or monitors are equipped with component video inputs that
are capable of reproducing a progressively scanned video signal.
Connecting to these inputs allows you to view the highest quality
pictures with less flicker.
Interlaced outputs/inputs
Some TVs or monitors are equipped with component video inputs.
Connecting to these inputs allows you to enjoy higher quality picture
playback.
In some TVs or monitors, the color levels of the playback picture may
be reduced slightly or the tint may change. In such a case, adjust the
TV or monitor for optimum performance.
To switch the output signal (Progressive/Interlaced)
Press PROGRESSIVE on the remote control.
The output signal alternates between component progressive and
component interlaced. For details, refer to “Selecting Progressive
Scan Video Output” on page 42.
To component video
inputs
Y
PB
PR
Component video cable
(not supplied)
MULTI CHANNEL OUTPUT
: Signal flow
ANALOG OUTPUT
CENTER
SURR
FRONT
CH 1
CH 2
DO NOT connect the
power cord until all
connections are
complete.
DIGITAL OUTPUT
L
R
SUBWOOFER
COAXIAL
COMPONENT
Y
PB
S VIDEO
OPTICAL
CH 1
COAXIAL
OPTICAL
CH 2
VIDEO
AC INLET
PR
RS 232
CH 1
CH 2
VIDEO OUTPUT
: Signal flow
Making S-video connections
If the TV or monitor has an S-video input, making this type of
video connection will produce improved picture quality. Using an
S-video cable, connect the VIDEO OUTPUT S VIDEO CH1 or
CH2 jack to the corresponding S-video input jack on the TV.
Be sure to set Audio Out Select to “Analog 2Ch” using the onscreen menu explained in “Customizing the Function Settings”
starting on page 44. See page 48 for direct information.
S-video cable
(supplied)
To S-video
input
11
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p10-19.p65
11
10/2/00, 3:23 PM
Making Connections
Optional Audio Connections
This DVD Player provides numerous ways to take full advantage of the digital multi channel sound recorded on DVD media.
When listening to DVD-Audio
For full enjoyment of DVD-Audio media, it is recommended to make connections to the 6-channel ANALOG OUTPUT jacks. Audio output of DVD-Audio cannot
be played back efficiently when output as a bitstream or PCM from the DIGITAL OUTPUT jacks.
Analog connections
In addition to offering two stereo outputs for connection to a stereo system, two types of multi channel analog output allow you to make connections to an AV
component that features multi channel analog input for full enjoyment of multi channel DVD-Audio discs.
Making discrete 6-channel ANALOG
OUTPUT connections
An amplifier with six
channel discrete input
To audio inputs
FRONT L
FRONT R
SURROUND L
SURROUND R
CENTER
SUBWOOFER
The discrete ANALOG OUTPUT jacks are intended to deliver up to
5.1 channels of multi channel audio from DVD-Video and DVDAudio sources. Connections can be made from the ANALOG
OUTPUT FRONT, SURR (surround), CENTER, and SUBWOOFER
jacks to the corresponding input jacks on an AV component with
multi channel discrete audio input jacks.
Be sure to set Audio Out Select to “Analog 6Ch” using the onscreen menu explained in “Customizing the Function Settings”
starting on page 44. See page 48 for direct information.
Notes
• To ensure proper delivery of sound, be sure to match the names of the jacks
on the DVD Player and the component being connected to.
Audio cables
(not supplied)
MULTI CHANNEL OUTPUT
: Signal flow
ANALOG OUTPUT
CENTER
SURR
FRONT
CH 1
CH 2
DO NOT connect the
power cord until all
connections are
complete.
DIGITAL OUTPUT
L
R
SUBWOOFER
COAXIAL
COMPONENT
Y
S VIDEO
OPTICAL
CH 1
COAXIAL
OPTICAL
CH 2
VIDEO
AC INLET
PR
PB
RS 232
CH 1
CH 2
VIDEO OUTPUT
L (White)
R (Red)
: Signal flow
Audio cable
(not supplied)
L (White)
R (Red)
To audio inputs
An amplifier with
stereo inputs
Making stereo audio connections
By making connections to a stereo system, you can improve the
quality of the sound of cinematic presentations as well as make
effective use of the DVD Player’s ability to play back CDs.
Using an audio cable (sold separately), make audio connections
from the ANALOG OUTPUT CH1 or CH2 L and R jacks to the
corresponding jacks on the stereo component.
Be sure to set Audio Out Select to “Analog 2Ch” using the onscreen menu explained in “Customizing the Function Settings”
starting on page 44. See page 48 for direct information.
Notes
• Be sure to match the colors of the plugs on the cable with the
corresponding jacks on the DVD Player and the stereo component: red for
R (right) audio and white for L (left) audio.
• Do not make connections to the PHONO or TUNER jacks on the stereo
component.
• When this type of connection is made, be sure to set Audio Out Select to
“Analog 2Ch” in order to enjoy the Dolby Pro Logic surround sound.
12
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p10-19.p65
12
10/2/00, 3:23 PM
Making MULTI CHANNEL OUTPUT
connection
An amplifier with a multi channel
input jack
The MULTI CHANNEL OUTPUT is a DB-25 port that can output
up to 5.1 channels of decoded analog audio from DVD-Video and
DVD-Audio sources to a receiver or other AV component that
features a similar input port. Ideally you want to connect two
identical ports together via a single DB-25 cable.
Be sure to set Audio Out Select to “Analog 6Ch” using the onscreen menu explained in “Customizing the Function Settings”
starting on page 44. See page 48 for direct information.
DB-25 cable
(supplied)
Notes
Tighten
locking
screws
• When connecting the cable, be sure to secure the locking screws on the
DB-25 connectors.
• The output from this port is the same as from the 6-channel ANALOG
OUTPUT jacks.
MULTI CHANNEL OUTPUT
: Signal flow
ANALOG OUTPUT
CENTER
SURR
FRONT
CH 1
CH 2
DIGITAL OUTPUT
L
DO NOT connect the
power cord until all
connections are
complete.
R
SUBWOOFER
COAXIAL
COMPONENT
Y
PB
S VIDEO
OPTICAL
CH 1
COAXIAL
OPTICAL
CH 2
VIDEO
AC INLET
PR
RS 232
CH 1
CH 2
VIDEO OUTPUT
Optical cable
(not supplied)
Digital connections
Make digital connections from the DVD Player to an AV component
that features digital input capability or one or more multi-channel
audio decoders to realize the full cinematic experience made
possible by the DVD format. This DVD Player features two sets of
optical and coaxial digital audio output jacks and can output Dolby
Digital, DTS, and MPEG2* bitstreams as well as outputting
standard PCM.
Make connections from the DIGITAL OUTPUT OPTICAL CH1 or
CH2 jacks to the digital optical input jack on the AV component
using an optical fiber cable (sold separately). Make connections
from the DIGITAL OUTPUT COAXIAL CH1 or CH2 jacks to the
digital coaxial input jack on the AV component using a coaxial cable
(sold separately). It is not necessary to make more than one type of
digital connection to a single component.
When you are making connections to an amp or receiver that has
internal Dolby Digital, DTS, or MPEG decoding capabilities, set
Audio Out Select to “Bitstream” using the on-screen menu
explained in “Customizing the Function Settings” starting on page
44. See page 48 for direct information.
When you are making connections to an amp or receiver that has
digital input capabilities, but no internal decoder, set Audio Out
Select to “PCM” using the on-screen menu explained in
“Customizing the Function Settings” starting on page 44. See page
48 for direct information. Setting Audio Out Select to any other
setting could result in digital noise being output that
could cause harm your hearing and may also damage your speakers.
Coaxial cable
(not supplied)
To digital audio
input (optical)
To digital audio
input (coaxial)
: Signal flow
An amplifier with a Dolby
Digital, DTS, MPEG1, or
MPEG2* decorder or digital
input jacks
Notes
• Refer to the instructions supplied with the AV component for details on
what digital audio formats it is compatible with.
• After making digital audio connections, be sure to set Audio Out Select
appropriately for the type of digital signal the connected AV component is
compatible with using the on-screen menu explained in “Customizing the
Function Settings” starting on page 44. See page 48 for direct information.
• Even if digital audio connections are made, it is also recommended to
make analog connections, because some conditions or media may prohibit
digital audio output.
* Not applicable for USA and Canadian models
13
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p10-19.p65
13
10/2/00, 3:23 PM
Control Position and Names
Rear panel
MULTI CHANNEL OUTPUT
For operational instructions, see the page indicated in brackets [ ].
ANALOG OUTPUT
CENTER
SURR
FRONT
CH 1
CH 2
DIGITAL OUTPUT
L
R
SUBWOOFER
COAXIAL
COMPONENT
Y
PB
S VIDEO
OPTICAL
CH 1
COAXIAL
OPTICAL
CH 2
VIDEO
AC INLET
PR
RS 232
CH 1
CH 2
VIDEO OUTPUT
5.1-Channel SURROUND AUDIO OUT MULTI CHANNEL OUTPUT terminal [13]
5.1-Channel ANALOG OUTPUT [12]
2-Channel ANALOG OUTPUT [10,12]
DIGITAL OUTPUT COAXIAL, OPTICAL [13]
AC INLET [17]
VIDEO output [10]
S VIDEO output [11]
COMPONENT (PROGRESSIVE) VIDEO output (Y/PB/PR) [11]
RS 232 port (This port is to be used in conjunction with an external controller to control the operation of
the DV-S939 using an external device.)
14
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p10-19.p65
14
10/2/00, 3:23 PM
Front Panel
For operational instructions, see the page indicated in brackets [ ].
VIDEO CIRCUIT
OFF
POWER button [17]
SYANDBY indicator [17]
STANDBY/ON button [17]
VIDEO CIRCUIT OFF button [43]
Front panel display [16]
DISPLAY button [16, 38]
button [26]
button [26]
PLAY
STOP
button [20]
button [21]
OPEN/CLOSE
button [20]
Disc tray [20]
Audio sampling rate indicators [20]
15
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p10-19.p65
15
10/2/00, 3:23 PM
Control Position and Names
Display
Repeatedly pressing DIMMER on
the remote controller changes the
brightness of the display
For operational instructions, see the page indicated in brackets [ ].
→Normal→Dim→Very Dim→OFF
TITLE/GROUP indicator
PROGRESSIVE indicator [42]
RANDOM indicator [29]
Angle icon indicator [32]
CHP (Chapter)/TRACK indicator
Play mode indicators
REPEAT indicators [27]
Inserted disc indicator [20]
MEMORY indicator [28]
192 kHz Processing indicator
VIDEO OFF indicator [43]
Multifunction indicator (Indicates operating
status, messages, etc.)
TOTAL playing time/REMAINING time elapsed
time indicator
By repeatedly pressing DISPLAY on the front panel of the DVD Player, you can switch between the elapsed time and remaining time
displays.
DVD-Video
DVD-Audio
During playback:
During playback:
Example
Example
TITLE
CHP
GROUP
TRACK
DVD
Playing chapter
3 of title 2
DVD - AUDIO
Elapsed time of
the current
chapter
Playing track 3 Elapsed time of
the current track
of group 2
Notes
• Some discs may not display chapter numbers.
• A time indication not accompanied with a chapter number shows elapsed
time of a segment within the current time.
Video CD
CD
During playback:
During playback:
Example
Example
TRACK
TRACK
VCD
Playing track 3
Elapsed time of
the current track
CD
Playing track 3
Note
Some discs may not display track numbers or elapsed time.
16
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p10-19.p65
16
10/2/00, 3:23 PM
Elapsed time of
the current track
Connecting the Power/
Turning on the DVD Player
Before connecting the POWER
• The DV-S939 is shipped with the main power
(POWER) switch in the on position ( ON).
When the power cord is plugged in for the first
time, the DV-S939 will automatically enter the
standby state and the STANDBY indicator will
light (same condition after step 2 below).
• Make sure that all appropriate connections have been
completed as described on pages 10 to 13.
• Turning on the DVD Player may cause a momentary
power surge, which might interfere with other electrical
equipment such as computers. To prevent interference,
use a wall outlet on a different circuit.
1
Plug the supplied power cord into
the AC INLET and then into the
power outlet on the wall.
AC INLET
Power cord
(supplied)
To a wall outlet
Notes
• Do not use a power cord other than the one supplied with the DV-S939. The
power cord supplied is designed for use with the DV-S939 and should not be
used with any other device.
• Never have the power cord disconnected from the DV-S939 while the other
end is plugged into the wall outlet. Doing so may cause an electric shock.
Always connect by plugging into the wall outlet last and and disconnect by
unplugging from the wall outlet first.
S TA N D B Y / O N
VIDEO CIRCUIT
OFF
DISPLAY
OPEN/CLOSE
STANDBY
STOP
PLAY
POWER
48/44.1 96/88.2 192/176.4
ON
OFF
2
Press POWER to switch on the
main power.
The DVD Player enters standby mode.
The STANDBY indicator lights up.
Notes
• The buttons on the remote controller do not operate if the POWER switch is
set to OFF.
• To switch off the main power, press POWER again.
3
Press STANDBY/ON on the DVD
Player or ON on the remote controller.
The DVD Player turns on and the STANDBY indicator turns off.
The first time you turn on the DVD Player, the Initial Setup screen
appears.
Press ENTER, then follow the procedure on page 54 to set up your DVD Player for
the first time.
Notes
• To put the DVD Player in the standby mode, press STANDBY/ON on the DVD Player, or
STNBY (or ON) on the remote controller. Be sure to set the volume to minimum before
putting the DVD Player in the standby mode for the next use to avoid sudden loud sound
reproduction.
• While the STANDBY indicator lights up, the DVD Player can receive signals from the remote
controller. However, if you press POWER on the DVD Player to switch off the main power,
the remote controller cannot be used to turn on the DVD Player.
• You can change the First Setup later with “Customizing the Function Settings” starting from
page 44.
• Setting the STANDBY button to standby does not shut off the power completely.
17
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p10-19.p65
17
10/2/00, 3:23 PM
Setting up the DVD Player for
Optimal Performance
Using the Remote Control to Navigate On-screen Displays
On-screen navigation is a simple procedure that is done mostly by using / / / and ENTER on the supplied remote controller. To move the
highlighted section on the screen (cursor), simply press the edge of the button that corresponds to the direction you wish to move in ( / / / ).
Press the center of the button (ENTER) to enter settings or selections.
About the disc menu
DVD-V
DVD-A
A DVD-Video or DVD-Audio may include more than one language and more
than one sound system. In many instances, such DVD let you choose the
language (e.g. disc menu language/audio language/subtitle language), sound
system, and so on using the menu.
Depending on the disc, the name of the disc menu varies and the disc menu may
be included in the main menu.
About the title menu
DVD-V
DVD-A
VCD
DVD-Video, DVD-Audio, or Video CD with PBC (Playback Control) function
(see “About Video CDs” on page 7) may let you locate a title, chapter, group, or
track (see page 7) using the menu.
Depending on the disc, the name of the title menu varies and the title menu may
be included in the main menu.
The following buttons are also used in conjunction with onscreen navigation.
SETUP:
Press to display the Setup screen when you wish to
make changes or adjustments in the DVD Player
performance settings. For details of the DVD Player
settings, refer to “Customizing the Function Settings”
starting from page 44.
MENU and TOP MENU: These button select the menu screen(s) recorded on
DVD media.
DISPLAY/NAVI:
This button displays information about the current
settings of the disc loaded in the player and also
offers a variety of playback options (see page 38).
RETURN:
Press to return to a previous screen or setting. This
button is convenient when you do not wish to change
a setting or selection.
18
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p10-19.p65
18
10/2/00, 3:23 PM
DVD-V
DVD-A
Various sound formats and sound effects
Minimum speaker configuration for
DTS/Dolby Digital/MPEG2* surround sounds
Center Speaker
Left
front
speaker
Right
front
speaker
Left
surround
speaker
Right
surround
speaker
The 5.1-channel digital surround format of DOLBY DIGITAL/DTS/
MPEG2* enables you to individually play five full-range (20 Hz-20
kHz) channels (left and right front, center, two surround channels) plus
an LFE (Low Frequency Effect) channel for the low-range effect sound.
It will create a realistic sound as heard in theaters and concert halls.
DOLBY DIGITAL Surround
DVD Video that have the
D I G I T A L
mark are recorded using this system.
DTS Surround
DVD Video and CD that have the
mark are recorded using this system.
MPEG2*
DVD Video that have the
mark are recorded using this
system. MPEG2* may have 8 channels. In this case, left and right center
speakers in addition to the above speaker configuration are used.
DOLBY PRO LOGIC Surround
This surround format consists of 4 channels (left and right front, center, and
monaural surround channel) and emphasizes the center channel. This format is
very effective for panning music, conversation, and three-dimensional sound
movement output from three front channels. It also simulates the atmosphere
and surround effects of the sound reflected from the side and rear walls of the
theater.
DVD Video that have the
mark are recorded using this system.
* Not applicable for USA and Canadian models
19
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p10-19.p65
19
10/2/00, 3:23 PM
Playing DVD-Video/Audio,
Video CD, and CD
Before playing
• DVD-Video, DVD-Audio, Video CD, CD, CD-R and CD-RW can be played with the DVD Player (see
“Playable Discs” on page 6). Do not play anything else.
• When playing DVD-Video, Video CD, or DVD-Audio with video features, turn on the TV and set the TV
to the DVD Player's input.
• If an audio system is connected to the DVD Player, turn on the audio system and set it to the DVD
Player’s input.
About the
DVD-V
,
DVD-A
,
VCD
and
CD
marks in the pages related to disc operation
DVD-A means the function or title is related to DVD-Audio operation.
DVD-V means the function or title is related to DVD-Video operation.
VCD means the function or title is related to Video CD operation.
CD means the function or title is related to audio CD operation.
DVD-V
DVD-A
VCD
Warning
If the DVD Player is connected to the TV or
amplifier through the analog audio jacks, do not
play DTS-encoded discs. Excessive noise may
be output from the analog stereo jacks, which
may damage the connected equipment.
To reproduce DTS surround sounds, digital
connection to an amplifier with a DTS decoder
is needed.
CD
Basic Playback
1
Press
If the DVD Player is in standby mode
when the button is pressed
.
The DVD Player turns on and the disc tray opens.
In this case, it takes several seconds until the disc
tray opens.
The disc tray opens.
2
Place a disc on the disc tray.
Put the disc in the tray with the label
side facing up.
There are two different disc sizes.
Place the disc in the correct guide on
the disc tray.
S TA N D B Y / O N
VIDEO CIRCUIT
OFF
DISPLAY
OPEN/CLOSE
Whenever a disc is loaded in the
player, indicators above and
light up.
48/44.1 96/88.2 192/176.4
VIDEO CIRCUIT
OFF
DISPLAY
OPEN/CLOSE
STANDBY
STOP
PLAY
POWER
48/44.1 96/88.2 192/176.4
ON
3
OFF
Press
.
DVD
The disc tray closes and playback starts.
If you press to close the tray after step 2, playback
may automatically start depending on the disc.
48/44.1 96/88.2 192/176.4
The appropriate disc indicator lights, and the audio
sampling rate indicator also lights.
For the other information that appears in the display,
see page 35.
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
20
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p20-26.p65
20
10/2/00, 3:23 PM
If the screen on the right
appears - Screen Saver
Tip to obtain a higher quality picture
Occasionally, some picture noise not usually visible during a normal
broadcast may appear on the TV screen while playing a DVD-Video
because the high resolution pictures on these discs include a lot of
information. While the amount of noise depends on the TV you use,
you should generally adjust the TV to reduce sharpness when viewing
DVD-Videos.
If you pause for a long time, the screen
saver operates.
To resume normal playback, press
(You can set this function to Off using
the menu explained in “Customizing the
Function Settings” starting from page
44. See page 51 for direct information.)
To play NTSC discs (Multisystem TV is needed)*
Set “PAL/Auto” to “Auto” using the menu explained in “Customizing
the Function Settings” starting from page 44. See page 47 for direct
information.
* Not applicable for USA and Canadian models
To remove the disc
Press to open the disc tray.
Remove the disc after the disc tray opens completely.
After removing the disc, be sure to press the button again to close the tray.
To pause playback (still mode)/
Playing frame by frame
Press
during playback.
To start playback, press
.
To play frame by frame
DVD-V
VCD
1
Press the button repeatedly during pause. Each time you press the button the picture
advances one frame.
To resume normal playback, press
.
Notes
• The sound is muted during still mode and frame by frame playback.
• When using a DVD-Audio that includes pictures, this operation may be permitted
in some picture segments.
To stop playback
Press .
When you press
to restart playback, playback starts from the location
where you stopped playback because the location index is stored in memory.
3
Note
The location where playback resumes may vary depending on the disc or the scene
where you stopped.
Resuming playback from the beginning
Press again after stopping playback to clear the location index memory, then press
to start playback.
DVD-V
DVD-A
VCD
CD
Playback starts from the beginning of the current title.
Playback starts from the beginning of the current group.
Playback starts from the beginning of the disc.
To start playback from the beginning of the DVD-Video or DVD-Audio, press
to close the disc tray and start playback.
open the disc tray then press
Notes
to
Notes
The location index memory will also be cleared when:
• The power cord is unplugged.
• The disc tray is opened.
• The parental lock setting is changed (see page 52) or a disc menu language is
selected (see page 50).
• The location where playback resumes may vary depending on the disc or the scene
where you stopped. With DVD-Audio, playback may restart from the beginning of
the track.
• To change the Audio Out Select (see page 48) or the On-Screen Language (see
page 50) settings, press after stopping playback to clear the location index.
Please note that resumed playback is not possible after this is done.
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p20-26.p65
21
• Do not move the DVD Player during playback. Doing so may
damage the disc.
• Use
on the remote controller or DVD Player to open and
close the disc tray. Do not touch the disc tray while it is
moving. Doing so may cause the DVD Player to malfunction.
• Do not press down on the disc tray or put any objects other
than playable discs on the disc tray. Doing so may cause the
DVD Player to malfunction.
• In many instances, a menu screen appears when playback of a
movie is complete. Prolonged display of an on-screen menu
may damage your television set, permanently etching that
image onto its screen. To avoid this, be sure to press once
the movie is complete.
21
10/2/00, 3:24 PM
Playing DVD-Video/Audio, Video CD, and CD
To play in fast reverse or fast forward
DVD-V
DVD-A
VCD
CD
During normal playback, press
for fast reverse playback or
for
fast forward playback.
Each press of the same button changes the playback speed.
The rate and direction of playback is indicated by arrow marks ( or ) in the corner
of the screen.
To resume normal playback.
Press
.
Notes
• The DVD Player mutes sounds and omits subtitles during reverse and forward scan of DVDVideo.
• The playback speed may differ depending on the disc.
• Fast reverse and fast forward playback may not be possible with some DVD-Audio.
To play in slow-motion
DVD-V
VCD
Press SLOW during playback.
:Each time you press
, the slow-motion speed changes.
:If you press
during playback, you can view the picture in reverse slow
motion. (Only when using a DVD-Video.)
, the slow motion speed changes.
Each time you press
To resume normal playback.
Press
.
Notes
• The sound is muted during slow-motion playback.
• The playback speed may differ depending on the disc.
• When using a DVD-Audio that includes pictures, this operation may be permitted in some
picture segments.
To control still pictures
DVD-A
DVD-Audio may include still pictures, which are classified into two large groups.
Slideshow:
Still pictures appear one after another automatically consistent
with the disc program.
Browsable pictures: You can display your favorite still picture selected with the buttons
on the remote control.
STILL +/–:
To select a picture. (The order of pictures vary depending on the
disc.)
RETURN:
To return to an initial one programmed on the disc.
22
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p20-26.p65
22
10/2/00, 3:24 PM
23
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p20-26.p65
23
10/2/00, 3:24 PM
Locating a Specific Title/Group/
Chapter/Track/Location
The structure of the disc content
DVD-Audio
The contents of DVD-Audio are divided into groups, and the
groups are subdivided into tracks.
DVD-Video
Normally, the contents of DVD-Video are divided into
titles, and the titles are subdivided into chapters.
Title 1
Title 2
Group 1
Track 1
Track 2
Chapter 1Chapter 2 Chapter 1 Chapter 2Chapter 3
Track 1
Group 2
Track 3
Track 2
DVD-V
Locating a Title Using the Title Menu
If a DVD-Video contains a title menu, you can locate a specific title using the title menu function.
1
Press TOP MENU. (Depending on
the DVD-Video, press MENU.)
The title menu appears on the TV screen.
Example of a title menu.
2
TITLE 1
TITLE 2
TITLE 3
TITLE 4
Press / / /
you want.
Notes
• The instructions above describe basic procedures which may vary
depending on the contents of the DVD-Video. If different instructions
appear on the TV screen, follow those instructions.
• If you display the title menu during playback and press TOP MENU
again without selecting any title, the DVD Player usually resumes
playback from the point where you first pressed TOP MENU. (There
may be exceptional cases depending on the disc.)
• This method of locating a title is available only on a disc that contains a
top menu.
• The name of the button in the instruction notes of discs varies depending
on the disc.
to select the title
If the titles in the title
menu are assigned a
number, you can also
directly locate a
specific title using the
number buttons.
3
Press ENTER.
The DVD Player starts playback from chapter
1 of the selected title.
24
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p20-26.p65
24
10/2/00, 3:24 PM
MENU
TOP MENU
Video CD/CD
Video CD and CD are divided into tracks.
Track 1
Track 2
Track 3
ENTER
Track 4
Track 5
CLEAR
Number
buttons
DVD-V
DVD-A
VCD
SEARCH
CD
Locating a specific title and chapter or group and track by entering the numbers
If a DVD-Video or DVD-Audio contains the numbers corresponding to the titles and chapters, or group and tracks you can locate a specific
chapter in a specific title directly by entering the numbers.
1
Press SEARCH.
Skip steps 1 and 2 if you are using a Video
CD/CD.
The following display appears.
DVD-V
DVD-A
e.g.
Title: 1
Chapter:
2
1
Group: 1
Track : 1
Press / to select a section you
want to locate.
e.g. When you want to locate a chapter or
track.
DVD-V
DVD-A
e.g.
Title: 1
Chapter:
3
1
Group: 1
Track : 1
Press the corresponding number
buttons for the section you want.
e.g. To select chapter or track 25.
4
Repeat steps 2 and 3 if necessary.
5
Press
.
The DVD Player starts playback from the
selected section.
Notes
• Pressing CLEAR resets the numbers. To clear the display, press
SEARCH several times.
• This method of locating a title/group is available only on a disc that
contains title/group numbers.
Playing bonus groups of DVD-Audio
Some DVD-Audio may include an extra content called “Bonus
Group”.
If you select it to play, a display appears to enter a key number.
Press the number buttons on the remote control to enter the key
number.
When the number is entered correctly, playback of the bonus group
starts.
To get key numbers, refer to instruction note of discs.
or
Notes
• A key number may be called in some cases such as when removing the
disc. Enter the key number again if necessary.
• When you use a bonus group in a programmed play such as memory
playback, enter the key number beforehand.
25
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p20-26.p65
25
10/2/00, 3:24 PM
Locating a Specific Title/
Group/Chapter/Track/Location
S TA N D B Y / O N
VIDEO CIRCUIT
OFF
DISPLAY
OPEN/CLOSE
STANDBY
STOP
Number
buttons
PLAY
POWER
48/44.1 96/88.2 192/176.4
ON
OFF
SEARCH
DVD-V
DVD-A
VCD
CD
Locating a Specific Chapter or Track
Consecutively
You can locate consecutive chapters or tracks.
Remote controller
Press
or
(repeatedly) to
select the chapter or track you wish
to start playing.
DVD-V
VCD
CD
Locating a Specific Location by
Entering the Time
You can locate a specific location by entering its corresponding
time (hours, minutes, and seconds).
1
Press
once to start playback from the
beginning of the current chapter or track.
repeatedly to select the former
Press
chapters or tracks in reverse order.
Press
repeatedly to select the next
chapter or track in order.
Press SEARCH twice.
You may need to press the button more than
twice (depending on the disc) until the
following display appears.
Time - : - - : - -
2
Press the number buttons to enter
the location’s time.
The entered number appears on the right end
of the field, then shifts to the left each time
the next number is entered.
DVD Player
e.g.
Hours
Minutes Seconds
Time 1:25:30
Note
If the location time you enter exceeds the total
playing time of the disc, the setting will be
cancelled.
Notes
• Some titles may not display chapter numbers. Some groups may not
display track numbers.
• When you set “Title/Group Stop” to “Off” (see page 53), you can locate
consecutive chapters in another title or tracks in another group. If you go
, the DVD Player
back to the preceding title or group by pressing
locates the first chapter of the title or the first track of the group. When
“Title/Group Stop” is set to “On”, you can locate consecutive chapters or
tracks only within the current title or group.
3
Press
.
The DVD Player starts playback from the
entered location.
Notes
• Some discs may not respond to this procedure.
• Some scenes may not be located precisely.
• This method for accessing specific locations is available only within the
current title of the DVD-Video or within the current track of the Video
CD/CD.
26
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p20-26.p65
26
10/2/00, 3:24 PM
Playing Repeatedly
REPEAT
A-B
CLEAR
You can play a specific title, group, chapter, track, or segment
repeatedly (Title/Group repeat, chapter/track repeat, A-B repeat).
DVD-V
DVD-A
VCD
DVD-V
CD
Repeating a Title, Group, Chapter, or
Track
VCD
CD
Repeating a Specific Segment
You can play a specific segment repeatedly (A-B repeat).
You can play the same title, group, chapter, or track repeatedly
(Title/group, chapter/track repeat).
1
Press A-B at the beginning of the
segment (point A) you want to play
repeatedly.
Press REPEAT.
Each time you press REPEAT, the repeat
mode changes as follows.
A–
Chapter Repeat
→ DVD-V Chapter Repeat
DVD-A
Track Repeat
Repeats the current
chapter.
Repeats the current track.
Title Repeat
Group Repeat
Track Repeat
Track Repeat
Repeats the current title.
Repeats the current group.
Repeats the current track.
Repeats the current track.
All Repeat
Repeats the entire disc.
2
Press A-B again at the end of the
segment (point B).
A–B
↓
DVD-V
DVD-A
VCD
CD
The DVD Player automatically returns to
point A and starts repeat playback of the
selected segment (A-B).
↓
DVD-V
DVD-A
VCD
To resume normal playback
CD
↓
Repeat Off
To resume normal playback
Notes
• Some discs may not permit A-B repeat operation.
• You can play a specific segment only within the current title, chapter, or
track.
• You cannot set the A-B repeat function for segments that include
multiple camera angles.
• There may be a slight difference between point A and the location where
playback actually resumes depending on the disc.
Press CLEAR.
Note
• Some discs may not permit repeat operation.
• When playback is stopped, be sure to press
after you select the repeat play mode.
Press CLEAR.
Resumes normal
playback.
within about 5 seconds
27
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p27-35.p65
27
10/2/00, 3:24 PM
Playing in a Favorite Order
Title : 2
Chapter : 25
Title : 2
Chapter : 12
ENTER
RETURN
Title : 1
Chapter : 1
MEMORY
DISPLAY/NAVI
REPEAT
CLEAR
Number
buttons
You can combine your favorite titles, groups, chapters, or tracks
and play them in any order. You can program up to 30 selections
into the memory (Memory playback).
DVD-V
DVD-A
VCD
CD
Setting Titles, Groups, Chapters, or Tracks in a Favorite Order
The DVD Player automatically plays titles, groups, chapters, or tracks in the order you program.
1
Insert a disc and press MEMORY
while the disc is stopped.
VCD
Press the number button(s) to
select the track number, then press
ENTER to confirm.
The following display appears.
1
2
3
4
5
6
7
TG:
CT:
2
DVD-V
Repeat this step to select the next track.
Memory List
TG: -- CT: -TG: -- CT: -TG: -- CT: -TG: -- CT: -TG: -- CT: -TG: -- CT: -TG: -- CT: --
The space of “TG” may be showing a number.
Neglect this number when using a Video-CD/CD.
Title number or group number
Chapter number or track number
DVD-A
1 Press the number button(s) to
enter the title or group number.
2 Press to highlight “--” below CT.
3 Press the number button(s) to
enter the chapter or track
number.
4 Press ENTER to confirm.
To select another chapter/track in the
same title/group
Press the number button(s) for another chapter/track.
e.g. To play chapter 25 in title 2, chapter 12
in title 2, all the chapters in title 1, and
chapter 2 in title 4.
Title number
Step 1
Step 2
Step 3
Step 4
CD
Chapter number
While the Memory List is displayed,
press .
3
The DVD Player starts memory playback.
To change the entered step
While the Memory List is displayed, press / to highlight the
item. To select another title/chapter, group/track, or track, follow
step 2.
To cancel the entered step
While the Memory List is displayed, press
item. To cancel, press CLEAR.
/
to highlight the
To resume normal playback
Press CLEAR.
The memory playback indicator disappears.
To program during playback
If you press MEMORY during playback, the display to accept your
programming appears. To display the Memory List, press QUICK,
press / to select Memory List, then follow steps 2 and 3.
Notes
28
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p27-35.p65
28
• You can also use
(plus ten button) to add ten to the number.
• Some discs may not permit memory playback operation.
• If you press REPEAT during memory playback, the DVD Player repeats
the current memory playback.
• If you press MEMORY or RETURN while the “Memory List” display
appears on the TV screen, the “Memory List” display disappears.
• The programmed selections will be cleared when you turn off the DVD
Player.
10/2/00, 3:24 PM
Playing in Random Order
Title : 1: 1
TITLE
CHAPTER
Chapter
: 3: 3
RANDOM
Title : 3
Chapter : 1
Title : 2
Chapter : 2
CLEAR
You can play titles, chapters within a title, or tracks in random
order (Random playback).
DVD-V
VCD
CD
Playing Titles, Chapters or Tracks in Random Order
The DVD Player automatically selects the titles in DVD-Video, or tracks in Video-CD, CD, and plays them randomly.
Press RANDOM repeatedly to
change the random play mode as
follows.
To resume normal playback
Press CLEAR.
Chapter Random
Notes
→ DVD-V
Chapter Random
Plays the chapters
within the current title
in random order.
DVD-V
Title Random
VCD
Track Random
CD
Track Random
Plays the titles in
random order.
Plays the tracks in
random order.
Plays the tracks in
random order.
↓
↓
Random Off
• Some discs may not permit random playback operation.
• You cannot use the random playback function together with the memory
playback function.
• If you press
during random playback, the DVD Player goes to
another title or track and continues random playback.
Resume normal
playback.
If you press RANDOM during playback, the
DVD Player automatically starts random
playback after finishing the current title,
chapter or track.
Note
When playback is stopped, be sure to press
after you select the random play mode.
within about 5 seconds
29
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p27-35.p65
29
10/2/00, 3:24 PM
Zooming a Picture
ZOOM +/—
ZOOM ON
You can magnify areas within a picture.
CLEAR
DVD-V
Zooming a Picture and Shifting the Zoom Point
You can zoom in on a picture. You can also shift the zoom point.
Press ZOOM ON during normal,
slow, or still playback.
To resume normal playback
Adjust the magnification of the screen using
ZOOM + (to enlarge) and ZOOM – (to
reduce).
Press ZOOM ON repeatedly so that “Zoom
Off” appears.
Notes
To shift the zoom point
Press
/
/ /
.
• Some discs may not permit zoom operation.
• During some scenes, the buttons may not work as described above.
• Zooming does not work on subtitles or menu screens included on DVDVideo.
• While a zoom operation is being performed, it is not possible to select
the DVD menu. To select the DVD menu, cancel the zoom operation to
resume normal playback, and then select the DVD menu.
• The magnification level varies depending on the picture size you select
(see pages 44 and 46).
• When using a DVD-Audio disc that includes pictures, this operation may
be permitted in some picture segments.
To restore the original zoom point (center
of the picture)
Press CLEAR.
30
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p27-35.p65
30
10/2/00, 3:24 PM
Improving Picture Quality
DNR
You can view a picture with less video noise.
DVD-V
VCD
Selecting DNR Picture Enhancement
Press DNR on the remote controller
during playback.
The current setting is displayed.
Each time you press DNR, the setting changes
as follows.
3D DNR On
3D DNR Expanded
3D DNR Off
Normal level
Expanded
level
Notes
• Actual picture enhancement may vary depending on the quality of the
disc.
• Depending on the DNR setting selected, there may be no improvement in
the picture quality. When this is the case, set DNR to “Off”.
• Depending on the DNR setting, some kinds of picture details may be lost
by the picture enhancement.
• Depending on the disc, some kinds of picture details may be lost by the
picture enhancement.
• When using a DVD audio disc that includes pictures, this operation may
be permitted in some picture segments.
Off
3D DNR: Three Dimention Digital Noise
Reduction
31
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p27-35.p65
31
10/2/00, 3:24 PM
Selecting the Camera Angle
Angle : 1
Angle : 2
ANGLE
Angle : 3
You can select a preferred camera angle to watch a scene.
DVD-V
Changing the Camera Angle
If the scene was recorded from multiple angles, you can easily change the camera angle of the scene you are watching.
1
Press ANGLE while playing a scene
recorded with multiple angles.
While playing a scene recorded with multiple
angles, the angle icon ( ) appears in the
DVD display and on the TV screen.
Press ANGLE while the angle icon is
displayed.
To disable the angle icon display on the TV
Set “On-Screen Displays” to “Off” using the setting menu (see
pages 44 and 51).
Monitor the DVD display when you want to change the camera
angle.
Notes
Angle: 1/5
Angle icon
Current
angle
number
2
• You can change the camera angle during still playback. The camera
angle changes to the new setting when you resume normal playback.
• If you pause a picture immediately after changing the camera angle, the
resumed playback picture may not use the new camera angle.
• When using a DVD-Audio that includes pictures, if there are sections
during which multiple angles are recorded, it may be possible to change
the camera angle.
Press ANGLE or while the angle
number is displayed on the TV
screen.
Each time you press ANGLE or
angle changes.
, the camera
Angle: 1/5
Angle: 2/5
Angle: 3/5
: Cycles backwards
You can also change the camera angle directly
by pressing the number buttons corresponding
to the angle number.
32
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p27-35.p65
32
10/2/00, 3:24 PM
Selecting the Subtitle Language/
Turning On/Off Subtitles
Good evening!
Bon soir!
SUBTTL
¡Buenas tardes!
You can display subtitles on the TV screen and select a subtitle language
from those included on the DVD-Video.
DVD-V
DVD-V
Selecting a Subtitle Language
Turning Subtitles On/Off
You can select a subtitle language from those included on the DVDVideo.
1
1
Press SUBTTL during playback.
2
Press / while the subtitle setting is
displayed on the TV screen, to select “On” or
“Off”.
Press SUBTTL during playback.
The current subtitle setting is displayed for
about 3 seconds.
The current subtitle setting is displayed for
about 3 seconds.
Subtitle: 1 ENG On
Language
Subtitle : 1 ENG On
The abbreviation of the language appears
instead of the language name. See the list of
languages and their abbreviations on page 55.
2
Press SUBTTL or while the
subtitle setting is displayed on the
TV screen.
Good evening!
Displayed
for about
3 seconds
Subtitles
Subtitle : 1 ENG Off
Each time you press SUBTTL or , the
subtitle languages included on the DVDVideo disc change.
e.g.
Subtitle : 1 ENG On
Subtitle : 2 FRE On
Subtitle : 3 SPA On
: Cycles backwards
To turn off the subtitle setting display
Press CLEAR.
Notes
• Some DVD-Video are set to display subtitles automatically, and you
cannot turn them off even if you set the subtitle function to off.
• During some scenes, the subtitles may not appear immediately after you
select “On”.
• Some DVD-Video will allow you to make subtitle selections and turn
subtitles on or off only by using the disc menu.
• When using a DVD-Audio that includes pictures, if subtitle information
has been recorded on the disc, it may be possible to select a subtitle
language.
Notes
• When you turn on the DVD Player or replace a disc, the DVD Player
returns to the automatic setting in the setting menu (see pages 44 and
50).
When you select a subtitle language which is not included on the disc,
the DVD Player plays the prior language programmed on the disc.
• During some scenes, the subtitles may not appear immediately after you
change the subtitle language by pressing / .
33
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p27-35.p65
33
10/2/00, 3:24 PM
Selecting the Audio Language
AUDIO
MENU
Good morning!
Bon jour!
ENTER
¡Buenos días!
You can select a preferred audio language and sound system.
DVD-V
DVD-A
Selecting a Playback Audio Setting
You can select the preferred audio language and sound system as a
set from those included on the disc. This function lets you
temporarily change the audio language which you selected as the
automatic setting in the setting menu (see pages 44 and 50), and
choose the sound system if the disc is recorded in more than one
sound format.
1
Press AUDIO during playback.
Notes
• Depending on the disc, it may be necessary to select the audio sound
track using the DVD menu. When this is the case, press MENU to open
the DVD menu and select the appropriate sound track as indicated on the
DVD menu screen.
• When the DVD Player is turned on or when the disc is changed, the
audio settings are restored to the presets. In some cases, a language
recorded on the disc may be given priority and selected automatically
when the disc is loaded regardless of the setting.
• Depending on the DVD-Audio, the sampling frequency and bitrate may
be displayed.
• When using a DVD-Audio, changing the audio sound track may cause
playback to start again from the beginning of the current track.
Audio language
Sound system
Audio channel
e.g. DVD-V
Audio: 1 ENG PCM 2CH
Audio OUT Select : Bitstream
Audio Out Select
(see page 48)
The abbreviation of the language appears.
Refer to the list of languages on page 55.
2
Press AUDIO or while the audio
setting is displayed on the TV
screen.
Each time you press AUDIO or , the
language and audio recording system set
changes.
e.g. DVD-V
A u d i o : 1 ENG
5.1CH
A u d i o : 2 ENG PCM 2CH
A u d i o : 3 FRE
5.1CH
VCD
Selecting Sound Channels on Video
CD
A Video CD may have left and right sound channels which contain
sounds or languages on each channel. You can switch these two
channels to hear a preferred sound or language.
: Cycles backwards
To turn off the audio setting display
Press CLEAR.
During playback, press AUDIO
(repeatedly) to select the sound
channel.
Notes
• Dolby Digital 5.1 Channel sound may be
displayed as “
D 6CH”.
• You can change the “Audio Out Select” setting
temporarily by pressing / .
• When using a DVD-Audio, it may not be possible
to change the “Audio Out Select” setting.
• Before changing the setting, read through the
explanation on “Audio Out Select” on page 48
and carefully select the setting.
34
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p27-35.p65
34
10/2/00, 3:24 PM
L.R
Both the left and right
channels are heard.
L
The left channel is heard.
R
The right channel is heard.
Output Sound Conversion Table
Audio Output from the DIGITAL OUTPUT and ANALOG OUTPUT Jacks
Corresponding to Disc Formats and the DVD Player Settings
Audio Out Select setting and the output jacks
Disc
Sound System
DOLBY DIGITAL
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
DVD Video Linear
PCM
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
DTS
MPEG2*1
Video CD
MPEG1
Linear PCM 44.1 kHz/16 bit
CD
DTS
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/20 bit
48 kHz/20 bit
44.1 kHz/24 bit
48 kHz/24 bit
88.2 kHz/16 bit
Linear 96 kHz/16 bit
PCM 88.2 kHz/20 bit
or
DVD Audio
96 kHz/20 bit
packed
PCM 88.2 kHz/24 bit
96 kHz/24 bit
*2 176.4 kHz/16 bit
*2 192 kHz/16 bit
*2 176.4 kHz/20 bit
*2 192 kHz/20 bit
*2 176.4 kHz/24 bit
*2 192 kHz/24 bit
Bitstream
Analog 6Ch
Analog 2Ch
PCM
DIGITAL
OUTPUT
ANALOG
OUTPUT
DIGITAL
OUTPUT
ANALOG
OUTPUT
DIGITAL
OUTPUT
ANALOG
OUTPUT
DIGITAL
OUTPUT
ANALOG
OUTPUT
Bitstream
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
Bitstream
Bitstream
44.1 kHz/16 bit
44.1 kHz/16 bit
Bitstream
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/16 bit
48 kHz/16 bit
—
—
—
—
—
—
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
—
48 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
(Noise is output)
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/20 bit
48 kHz/20 bit
44.1 kHz/24 bit
48 kHz/24 bit
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/20 bit
48 kHz/20 bit
44.1 kHz/20 bit
48 kHz/20 bit
176.4 kHz/16 bit
192 kHz/16 bit
176.4 kHz/20 bit
192 kHz/20 bit
176.4 kHz/24 bit
192 kHz/24 bit
—
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
Bitstream
—
—
44.1 kHz/16 bit
Bitstream
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/20 bit
—
48 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
(Noise is output)
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/20 bit
48 kHz/20 bit
44.1 kHz/24 bit
48 kHz/24 bit
88.2 kHz/16 bit
96 kHz/16 bit
88.2 kHz/20 bit
96 kHz/20 bit
88.2 kHz/24 bit
96 kHz/24 bit
176.4 kHz/16 bit
192 kHz/16 bit
176.4 kHz/20 bit
192 kHz/20 bit
176.4 kHz/24 bit
192 kHz/24 bit
Bitstream
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
—
—
—
Bitstream
Bitstream
44.1 kHz/16 bit
44.1 kHz/16 bit
Bitstream
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/16 bit
48 kHz/16 bit
—
—
—
—
—
—
—
—
—
—
—
—
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
—
48 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
(Noise is output)
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/20 bit
48 kHz/20 bit
44.1 kHz/24 bit
48 kHz/24 bit
88.2 kHz/16 bit
96 kHz/16 bit
88.2 kHz/20 bit
96 kHz/20 bit
88.2 kHz/24 bit
96 kHz/24 bit
176.4 kHz/16 bit
192 kHz/16 bit
176.4 kHz/20 bit
192 kHz/20 bit
176.4 kHz/24 bit
192 kHz/24 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
—
48 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
Bitstream
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/16 bit
48 kHz/16 bit
—
—
—
—
—
—
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
—
48 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
(Noise is output)
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/20 bit
48 kHz/20 bit
44.1 kHz/24 bit
48 kHz/24 bit
44.1 kHz/16 bit
48 kHz/16 bit
44.1 kHz/20 bit
48 kHz/20 bit
44.1 kHz/20 bit
48 kHz/20 bit
176.4 kHz/16 bit
192 kHz/16 bit
176.4 kHz/20 bit
192 kHz/20 bit
176.4 kHz/24 bit
192 kHz/24 bit
*1 Not applicable for USA and Canadian models
*2 2Ch Audio Output
—: No signal
Notes
• When using only two speakers for playback and play a multi channel disc that prohibits stereo downmixing, the sound from the right and left
speakers will be the right and left channels of the multi channel sound track as recorded on the disc. With these types of discs, it is often possible
that a 2-channel stereo sound track may also be recorded. Change the sound track to hear the audio correctly. (For details, refer to the
documentation supplied with the disc.)
• During playback of discs recorded with sampling rates higher than 48 kHz (for example 96 kHz), the 48/44.1 sampling rate indicator lights when
Audio Out Select is set to either Bitstream or PCM.
• When Audio Out Select is set to Analog 6Ch, two channel audio sources are output with DOLBY PRO LOGIC surround processing (except for
DVD-Audio).
35
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p27-35.p65
35
10/2/00, 3:24 PM
Using the Graphic Remote
Control - V.REMOTE
Pressing one button can display a graphics based
on-screen remote control that allows you to
control playback as if you were doing it from the
actual remote control.
ENTER
V.REMOTE
DVD-V
VCD
CD
Using the Graphic Remote Control
1
During playback, press V.REMOTE.
To turn off the Virtual Remote
The graphic remote controller (Virtual
Remote) appears on the screen.
Press V.REMOTE.
e.g. DVD-V
Title: 1 @
0:12:34
Chapt.: 2 @ 0:01:23
Audio
Subtitle
Angle
Switch the audio
sound track and
video selection.
Note
Some discs may not permit this operation.
Change the speed
and direction of
playback.
Navi
2
Play
Press / / / to select a desired
item, and press ENTER.
:
:
:
:
:
:
:
:
Navi:
Pause [21]/Frame by frame [21]
Normal playback [20]
Slow [22]
Forward skip [26]
Fast forward [22]
Reverse slow [22]
Reverse skip [26]
Fast reverse [22]
Accesses the Navi menu (DVD-Video
only) [38]
Audio:
Move the cursor control ( / ) to
select a desired audio language, and
press ENTER.
For details, see page 34.
Selecting the output sound format is not
possible here.
Subtitle: Move the cursor control ( / ) to
select a desired subtitle language, and
press ENTER.
For details, see page 33.
Angle: Move the cursor control ( / ) to
select a desired camera angle, and press
ENTER.
For details, see page 32.
36
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p36-43.p65
36
10/2/00, 3:25 PM
Selecting the Playback
Function - QUICK
Pressing one button can display a list of playback
functions which are relevant to your current
playback mode. You can check and modify them
from the list.
ENTER
QUICK
DVD-V
DVD-A
VCD
CD
Selecting the Playback Function
1
During playback, press QUICK.
The following on-screen display appears.
(The actual display will vary depending on the
playback status.)
For details, see the respective pages.
Press / to select a desired item,
and press ENTER.
Memory:
To program memory playback (see page 28).
Memory List: To list memory settings (see page 28).
Repeat:
To select the repeat playback mode (see page 27).
Random:
To select the random playback mode (see page 29).
Bitrate:
To activate/disable the bitrate display (see page 38).
Text:
To activate/disable the Text display.
Text display:
Displays DVD-Text data or CD-Text data if
included on the disc.
With DVD-Audio, Album text data is displayed if it
is recorded on the disc. Track information is not
displayed.
(Some text content recorded on the disc may not be
displayed properly depending on the disc.)
Exit:
To quit the on-screen display.
e.g. To change the repeat mode:
Note
e.g. DVD-V
Quick
Memory
Memoy List
Repeat
Random
Bit Rate
Text
Exit
2
Quick menu
Pressing QUICK again also exits the on-screen display.
Quick
Memory
A-B (Set A)
Memoy List
Chapter
Repeat
Title
Random
All
Bit Rate
Text
Exit
3
Press
/
to change the setting.
e.g. To select the chapter repeat mode:
Quick
Memory
A-B (Set A)
Memoy List
Chapter
Repeat
Title
Random
All
Bit Rate
Text
Exit
4
Press ENTER.
The on-screen display disappears and
playback will resume according to your
selection.
37
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p36-43.p65
37
10/2/00, 3:25 PM
Accessing Playback
Features - NAVI
ENTER
The NAVI menu provides an icon based display
from which you can easily access key playback
function.
DISPLAY
/NAVI
DVD-V
DVD-A
VCD
CD
NAVI menu items
1
Press DISPLAY/NAVI.
The NAVI menu appears.
3
Press ENTER.
4
Refer to the list on the next page
and follow the instructions detailed
on subsequent pages.
Selection details appears.
V-Remote
Angle Viewer
Capture
Navi
Zoom
Z
Title: 1
0:00:00
Chapter: 1 0:00:00
Audio
ENG1
5.1 CH
Subtitle ENG1 ON
Angle 1/5
Bit Rate: IIIIIIIIIIIII
DNR
Preview
Strobe Viewer
Each time you press DISPLAY/NAVI,
the display changes.
Title/Chapter: Elapsed time and remaining time of
the current title/chapter.
Audio:
Current audio setting.
Subtitle:
Current subtitle setting.
Angle:
Current angle setting.
Bit Rate:
Data transfer rate (Mbit/s)
Amount of picture, sound and
subtitle data in the DVD-Video disc
transferred per second.
The larger the value, the more data
processed, but this does not
necessarily insure better picture
quality.
Status display (playback mode, current DNR
setting, current zoom status, etc.)
When a DVD-Audio is loaded in the player,
depending on the audio format (sampling
frequency/bitrate) the corresponding indicators are
displayed as follows.
C (mono)
The audio is monaural.
Notes
• The NAVI menu will disappear by pressing DISPLAY/NAVI several
times.
• The number of feature icons on the display will vary depending on the
disc.
• Feature icons are displayed only when you play a DVD-Video.
Navi menu selections
V-Remote
You can control key playback functions
using the graphic based on-screen control
(see page 36).
Navi
Angle Viewer
You can display all camera angles
simultaneously and select your preferred
one from them (see page 39).
Zoom
Z
You can magnify areas within a picture (see
page 30).
L, R (L: Left channel, R: Right channel)
The audio is in stereo.
Lf, Rf, C, LFE, S, Ls, Rs
(Lf: Left front, R: Right front, C: Center,
LFE: subwoofer, S: Surround, Ls: Left surround,
Rs: Right surround)
The audio is multi channel.
2
Press / / /
feature icon.
to select a desired
For details on each feature, refer to the list on
this page.
You can divide a desired scene into stop
action frames for careful analysis (see page
39).
Strobe Viewer
Preview
DNR
Capture
You can display thumbnail views of the first
scenes of titles or chapters and select a
preferred one (see page 40).
You can view a picture with less video noise
(see page 40).
You can sample a scene from a playback
picture and transform it into a background
picture (see page 41).
38
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p36-43.p65
38
10/2/00, 3:25 PM
can display all camera angles
Angle Viewer You
simultaneously and select your preferred one
You can divide a desired scene into stop
action frames for careful analysis.
from them.
Strobe Viewer
After selecting this icon and pressing ENTER, the following onscreen display appears:
After selecting this icon and pressing ENTER, the following onscreen display appears:
e.g.
e.g.
1
2
3
4
5
6
7
8
9
Slow
Angle Viewer
Navi
Normal
Strobe Viewer
Exit
Fast
Navi
Exit
When the scene contains 9 camera angles:
1
Press
1-9:
Navi:
Exit:
2
/ / /
to select.
1
Press
/ / /
to select.
Slow: Still pictures at shorter intervals.
Normal: Still pictures at normal intervals.
Fast:
Still pictures at longer intervals.
>>:
To view the next series of 6 pictures.
Navi:
To return to the NAVI menu.
Exit:
To quit the on-screen display.
To select the camera angle.
To return to the NAVI menu.
To quit the on-screen display.
Press ENTER.
2
Press ENTER.
Note
Some discs or scenes may not permit this operation.
Note
Some discs or scenes may not permit this operation.
39
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p36-43.p65
39
10/2/00, 3:25 PM
Accessing Playback Features - NAVI
NAVI menu items
Preview
You can display thumbnail views of the first
scenes of titles or chapters and select a
preferred one.
You can view a picture with less video noise.
DNR
After selecting this icon and pressing ENTER, the following onscreen display appears:
After selecting this icon and pressing ENTER, the following onscreen display appears.
e.g.
e.g.
1
2
3
DNR
4
5
Title
6
Chapter
Preview
1
3D DNR On
3D DNR Expanded
3D DNR Off
Interval
Navi
Press
Exit
/ / /
to select.
1
1 - 6:
Title:
To locate the scene.
To display the first scene of titles (1 to
6).
Chapter: To display the first scenes of chapters (1
to 6).
Interval: To display scenes at intervals of about
10 minutes apart.
<<:
To go to the previous page.
>>:
To go to the next page.
Navi:
To return to the NAVI menu.
Exit:
To quit the on-screen display.
2
Press ENTER.
Press
/
to select.
3D DNR On:
Normal level.
3D DNR Expanded: Expanded level.
3D DNR Off:
Off.
2
Press ENTER.
Note
For details and notes on the DNR picture enhancement, see page 31.
Notes
• Some discs or scenes may not permit this operation.
• Some items may not be selected depending on the disc or scene.
• Some of the first scenes may not be picked up depending on the disc.
40
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p36-43.p65
40
10/2/00, 3:25 PM
Capture
You can sample a scene from a playback
picture and transform it into a background
picture.
After selecting this icon and pressing ENTER, the following onscreen display appears.
e.g.
Capture
Storing
Navi
Exit
1
Pause playback at a scene you
want to capture.
2
Press
/
to select.
Storing:To sample and store the current picture in
the player memory.
Navi:
To return to the NAVI menu.
Exit:
To quit the on-screen display.
3
Press ENTER.
The stored picture will be displayed as a
background picture when the player is in the
stop mode. It is necessary to confirm this
process via the setup menu (see page 51).
Notes
• You can store only one picture. Storing a new picture will erase the old
one.
• No operations are permitted during the process of the sampling and
storage of background picture.
41
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p36-43.p65
41
10/2/00, 3:25 PM
Selecting Progressive
Video Output
The DVD Player is capable of outputting
progressive scan video. As its name suggests,
progressive scan delivers the video image
sequentially across the horizontal lines of the TV
or monitor rather than the alternating odd and
even delivery of an interlace scan. The result is a
picture quality that best reflects the quality digital
video recorded on the DVD.
PROGRESSIVE
DVD-V
Selecting progressive scan
Press PROGRESSIVE on the
remote controller.
The PROGRESSIVE indicator lights in the
front panel.
To turn off the progressive scan, press the
button again until the PROGRESSIVE
indicator disappears.
Notes
• In order for this function to be effective, it is necessary to have made
component video connections to a TV or monitor that is compatible with
progressive scan.
• This function only works when the color system recorded on the disc is
NTSC.
42
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p36-43.p65
42
10/2/00, 3:25 PM
Turning Off the Video
Signal Output
The DVD-Player can be set playing audio
exclusively. In this case, you can obtain sound of
better quality, as the DVD Player does not process
video signals. (All the video output jacks send no
video signals.)
S TA N D B Y / O N
V.OFF
V IDE O CIRCUIT
OFF
STANDBY
POWER
48/44.1 96/88.2 192/176.4
ON
OFF
VIDEO CIRCUIT OFF
DVD-V
DVD-A
VCD
CD
Switching the video signal off
DVD Player
VIDEO CIRCUIT
OFF
Press VIDEO CIRCUIT OFF on the
DVD Player or V.OFF on the remote
controller repeatedly.
The VIDEO OFF indicator appears on the display.
To turn on the video circuitry, press the button
again.
Notes
• Some discs cannot be played without some on-screen menu interaction.
If this is the case, be sure to perform the on-screen procedures as
indicated before turning off the video signal processing circuitry.
• The VIDEO CIRCUIT OFF setting is canceled whenever the DVD
Player is turned off.
Remote
controller
43
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p36-43.p65
43
10/2/00, 3:25 PM
Customizing the Function Settings
When you insert a DVD-Video, DVD-Audio, Video CD, or CD, the various
functions of the DVD Player will be set (reset) according to the setting menu.
You can customize this setting menu according to your preferences.
ENTER
RETURN
SETUP
DVD-V
DVD-A
VCD
CD
Making Adjustments to Setting
1
Press SETUP.
The following setting menu appears.
4
Press / to change the setting,
then press ENTER.
Category
symbols
Picture
TV Shape
4:3 LB
Blacker than Black
Setting : Interlaced
Off
e.g. When you change the “TV Shape”
setting to “16:9 Widescreen”.
1
Setting : Progressive 1
Progressive 4:3 Output Full
Picture
Progressive Conversion Auto
TV Shape
4:3 LB
4:3 LetterBox
Blacker than Black
Setting : Interlaced
Off
4:3 Normal
16:9 Widescreen
1
Setting : Progressive 1
Progressive 4:3 Output Full
2
Progressive Conversion Auto
Press / to select a category
symbol for the setting you want to
change.
Picture performance settings
5
Further steps may be needed
depending on the item or setting.
Follow the steps described in the
explanation of each item starting
from page 46.
6
• To change the setting of other
items in the same category, repeat
steps 3 to 4.
Output sound settings
Language settings
• To change the setting of an item
in a different category, repeat
steps 2 to 4.
Display settings
Operational setting
7
To close the setting menu, press
SETUP.
Initial settings
To return to the previously displayed menu
3
Press / to select the item you
want to change, then press ENTER.
Press RETURN.
e.g. When you select “PICTURE” as the
category in step 2, then select “TV
Shape” as the item in this step.
Notes
Picture
TV Shape
4:3 LB
4:3 LetterBox
Blacker than black
Setting : Interlaced
Off
4:3 Normal
16:9 Widescreen
1
Setting : Progressive 1
Progressive 4:3 Output Full
• The on-screen display disappears when you press SETUP.
• SETUP can function even during normal playback, however some
operations may be inaccessible, and a message will appear. In this case, try
again after playback is stopped.
Progressive Conversion Auto
44
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p44-55.p65
44
10/2/00, 3:25 PM
Reference Table of the Setting Menu
Menu item
Related to*1
Details
Page
To select a picture size according to the aspect ratio of your TV.
46
TV Shape
DVD-V
Blacker than Black
DVD-V
VCD
To make an adjustment of the black level on your TV using a commercially
available test disc that contains adjustment signals.
46
Setting: Interlaced
DVD-V
VCD
To adjust the picture quality.
46
Setting: Progressive
DVD-V
VCD
To adjust the picture quality. (Only when connected to a PROGRESSIVE TV.)
47
Progressive 4:3 Output
DVD-V
VCD
To select the video output of pictures recorded in 4:3 format. (Only when
connected to a PROGRESSIVE TV.)
47
Progressive Conversion
DVD-V
To select the system of output signal. (Only when connected to a
PROGRESSIVE TV.)
47
PAL/Auto*2
DVD-V
VCD
To select th video system of a disc.
47
Audio Out Select
DVD-V
DVD-A
To select an output sound format corresponding to your system connection.
48
Dynamic Range Control
DVD-V
To turn on or off a function that makes faint sounds easier to hear even if you
lower the volume during late hours playback.
49
Karaoke Vocal
DVD-V
To turn on or off the vocal output during DVD KARAOKE disc playback.
49
On-Screen Language
DVD-V
To select a preferred language for on-screen displays.
50
Disc Menu Language
DVD-V
To select a preferred language for disc menus.
50
Audio Language
DVD-V
To select a preferred language for the sound.
50
Subtitle Language
DVD-V
To select a preferred language for subtitles.
51
On-Screen Displays
DVD-V
DVD-A
VCD
CD
To turn on or de-activate the operation status display on the TV screen.
51
Background
DVD-V
DVD-A
VCD
CD
To select the background color or background picture.
51
Screen Saver
DVD-V
To turn the screen saver on or off.
51
Pause/Still
DVD-V
To select the resolution of still pictures.
52
Parental Lock
DVD-V
To turn the parental lock function on or off.
52
Remote Confirmation
DVD-V
DVD-A
To turn on or off the confirmation beeper announcing when each remote
command received.
53
Title/Group Stop
DVD-V
DVD-A
PBC
VCD
Priority Contents
DVD-V
DVD-A
On-screen Language
TV Shape
Audio Out Select
DVD-V
DVD-A
DVD-A
VCD
VCD
VCD
CD
CD
CD
To turn on or off a feature that automatically stops playback after a title/group has 53
been viewed.
VCD
CD
To use the menu screen when playing a PBC-controllable Video CD.
53
To select the playback priority between DVD-Video and DVD-Audio format
signals.
53
To install the initial system setting.
54
*1 When using a DVD-Audio disc that includes pictures, some setting marked DVD-V may be effective.
*2 Not applicable for USA and Canadian models
45
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p44-55.p65
45
10/2/00, 3:25 PM
Customizing the Function Setting
Explanation of Each Item in the Picture Category
Picture
TV Shape
4:3 LB
Blacker than Black
Setting : Interlaced
Off
1
Setting : Progressive 1
Progressive 4:3 Output Full
Progressive Conversion Auto
TV Shape
4:3 Letterbox:
Setting: Interlaced
DVD-V
Select when a 4:3 TV is connected.
Displays theatrical images with masking
bars above and below the picture.
To select a preset memory setting:
Press /
ENTER.
Select when a 4:3 TV is connected.
Displays pictures cropped to fill your TV
screen. Either or both sides of the picture are
cut off.
to select a memory number (1 to 3), and press
Picture
TV Shape
4:3 LB
1
Blacker than Black
Setting : Interlaced
Off
2
3
1
Setting : Progressive 1
Progressive 4:3 Output Full
Progressive Conversion Auto
2
16:9 Widescreen:
VCD
You can fine adjust picture quality and store up to 3 custom picture
settings in the memory of the DVD Player.
1
4:3 Normal:
DVD-V
Press
/
to select the element, and press ENTER.
Select when a 16:9 wide TV is connected.
Notes
Setting Interlaced
• The displayable picture size is preset on each DVD-Video. Therefore, the
playback picture of some DVD-Video may not conform to the picture size
you select.
• When you play a DVD-Video recorded in the 4:3 picture size only, the
playback picture always appears in the 4:3 picture size regardless of the TV
shape setting.
• If you select “16:9 Widescreen” and you own a 4:3 TV set, the DVD
playback picture will be horizontally distorted during playback. Images
will appear to be horizontally compressed. Make sure the TV Shape
conforms to the actual TV in use.
Blacker than Black
DVD-V
VCD
Off: For normal use.
On: Select when you adjust the black level of your TV using a
commercially available test disc that contains adjustment
signals.
Contrast
0
Brightness
Color
0
Tint
Sharpness
0
0
Black Level
NRML
0
0
Gamma
Y/C Time Correction
Edge Enhance
3
Press
/
0
On
to adjust the value, and press ENTER.
(–7) Lower
Contrast
Higher (+7)
(–7) Darker
Brightness
Brighter (+7)
(–7) Duller
Color
Brighter (+7)
(–7) Redder
Tint
Greener (+7)
(–7) Softer
Sharpness
Sharper (+7)
Normal
Black Level
Enhanced
(–)
Gamma*1
(+)
(–3)
Y/C Time Correction*2
(+3)
On
Edge Enhance*3
Off
Note
With certain discs, the played picture may be disturbed if this item is set to
On. In this case, set this item to Off.
*1: Adjust when playback pictures are too dark or too whitish.
*2: Adjust horizontal color deviations. Pictures may shift horizontally
during the adjustment.
*3: Sharpens the edges of images.
Notes
• These adjustments are not available when connecting to a PROGRESSIVE
TV.
• The Tint adjustment is not available when connecting to a TV via the
component video jacks (Y, PB, PR).
46
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p44-55.p65
46
10/2/00, 3:25 PM
Setting: Progressive
DVD-V
VCD
You can fine adjust picture quality and store up to 3 picture setting
in the memory of the DVD Player. (Only when connected to a
PROGRESSIVE TV.)
To select a preset memory setting:
1
Press / to select a memory number (1 to 3), and press the
ENTER button.
Progressive Conversion
There are two types of source content in pictures recorded in DVDVideo: film content (pictures recorded from films at 24 frames per
second) and video content (video signals recorded at 30 frames per
second). Make this selection according to the type of content being
viewed.
Auto:
Picture
TV Shape
4:3 LB
1
Blacker than Black
Setting : Interlaced
Off
2
3
1
Video:
Setting : Progressive 1
Progressive 4:3 Output Full
Progressive Conversion Auto
Film:
2
Press
to select the element, and press the ENTER button.
/
Setting Progressive
3
Press
Contrast
0
Brightness
Color
0
Tint
Edge Enhance
0
/
DVD-V
Displays this operation normally.
The DVD Player automatically detects source content,
film or video, of playback source, and converts it in the
progressive output format in an appropreate method.
The DVD Player filters video signal, and converts it in
the progressive output format appropriately.
Suitable for playback of video content pictures.
The DVD Player converts film content pictures in the
progressive output format appropriated. Suitable for
playback of film content pictures. The progressive
output feature will be most effective under this selection.
Note
Depending on the disc, pictures may be cut off or doubled. In this case, select
“Video”.
0
Off
to adjust the value, and press the ENTER button.
(–7) Lower
(0) Darker
(–7) Duller
(–7) Redder
Contrast
Higher (+7)
Brightness
Brighter (+14)
Color
Brighter (+7)
Tint
Greener (+7)
Edge Enhance
To enhance picture edges.
(Off < On < Expanded1 < Expanded2)
PAL/Auto*
DVD-V
VCD
PAL:
Select to play PAL discs.
Connect a PAL TV to view pictures.
Auto:
The DVD Player automatically detects PAL and NTSC
video systems of discs.
Connecting a multisystem TV (PAL/NTSC compatible)
is needed to view pictures.
Note
Progressive 4:3 Output
DVD-V VCD
A playback picture may be distorted temporarily when the detected signal
changes between PAL and NTSC on the disc.
* Not applicable for USA and Canadian models
Select the video output of pictures recorded in 4:3 format. (Only
when connected to a PROGRESSIVE TV.)
4:3:
Full:
Displays images in 4:3 aspect ratio with masking bars to
the left and right of the picture.
Displays pictures expanded horizontally to fill the 16:9
screen.
47
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p44-55.p65
47
10/2/00, 3:25 PM
Customizing the Function Settings
Explanation of Each Item in the Audio Category
Audio
Audio Out Select
Bitstream
Dynamic Range Control Off
Karaoke Vocal
Off
Audio Out Select
When you select “Analog 6Ch”:
DVD-V
DVD-A
VCD
CD
Make the following setting for the built-in 5.1ch surround decorder.
Select the output sound format corresponding to your system
connection.
Analog 6ch
For details of sound recording systems, see “Output Sound
Conversion Table” on page 35.
C. S. Speaker Size
On
Subwoofer
Center Channel Delay 0msec
Bitstream:
Select when you connected to an amplifier
equipped with a Dolby Digital, DTS, MPEG1 or
MPEG2* decorder (see page 13).
The DVD Player outputs digital audio information
in the bitstream format when you play a DVDVideo recorded in the Dolby Digital, DTS, MPEG1
or MPEG2* recording system.
Analog 6Ch: Select when connected to an AV amplifier equipped
with 5.1ch audio inputs.
This DVD Player is equipped with a Dolby Digital
and MPEG decoder. The next screen will detail the
appropriate settings.
Analog 2Ch: Select when connected to a TV, or Dolby Pro Logic
or stereo system via the analog audio jacks (see
page 12).
PCM:
Select when connected to a 2 channel digital stereo
amplifier (see page 13).
The DVD Player outputs sounds in the PCM 2ch
format when you play a DVD-Video disc recorded
on the Dolby Digital, MPEG1 or MPEG2*
recording system.
* Not applicable for USA and Canadian models
Large
C (Center) Speaker On
S (Surround) Speaker On
Select an item by pressing
2
Make the setting (see below) by pressing ( / / / ), and press
ENTER.
C. S. Speaker Size
Small: When the center speaker or surround speakers cannot reproduce
low frequency signals below 120 Hz.
Large: When the center speaker and surround speakers can reproduce
low frequency signals below 120 Hz.
C (Center) Speaker
Off:
On:
When center speaker is not connected.
When you connect center speaker.
S (Surround) Speaker
Off:
On:
When surround speakers are not connected.
When you connect surround speakers.
Subwoofer
Off:
On:
When a subwoofer is not connected.
When you connect a subwoofer.
Note
Depending on the DVD-Audio, the audio may be output based only on
the channel information recorded on the disc regardless of the speaker
settings.
48
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p44-55.p65
48
/ , and press ENTER.
1
10/2/00, 3:25 PM
Adjusting the delay time:
Note
When enjoying 5.1ch surround playback, it is ideal to choose a listening
position that is the same distance from each speaker. By adjusting the
delay time of center/surround speakers, you can virtually create an ideal
listening environment (as if the center/surround speakers were at their
ideal locations respectively as below).
Depending on the disc, 6 channel sounds may not be output via the MULTI
CHANNEL OUTPUT/ANALOG OUTPUT jacks.
Ideal location of a
center speaker
Off:
On:
(A)
FL
FR
Dc
SW
Df
Ds
SL
SR
Dynamic Range Control
All speakers should
be located within a
circle with a radius
of Df.
DVD-V
Full dynamic range is maintained.
Dynamic range is reduced.
Notes
• This function works only during playback of Dolby Digital recorded discs.
• The level of Dynamic Range Reduction may differ depending on the DVD.
(B)
Ideal location of a
surround speaker
Center Channel Delay
0 msc:
When Df equals Dc.
1 msc:
When (A) is approx. 34 cm (13 inch)
2 msc:
When (A) is approx. 68 cm (27 inch)
3 msc:
When (A) is approx. 102 cm (40 inch) . . .
*(A)=Df – Dc
Get your optimum value (0, 1, 2 . . . 5) dividing (A) by 34.
Surround Channels Delay
Karaoke Vocal
Off:
On:
DVD-V
The primary vocal is not output.
The primary vocal is output when it is recorded on the
disc.
Notes
• The vocal output feature is used during playback of Dolby Digital (multichannel) recorded DVD KARAOKE discs. This feature allows you to turn
off vocal audio tracks, or restore them for background accompaniment.
• When playing KARAOKE, connect appropriate audio equipment such as
an amplifier to the DVD player.
0 msc:
When Df equals Ds.
1 msc:
When (B) is approx. 34 cm (13 inch)
2 msc:
When (B) is approx. 68 cm (27 inch)
3 msc:
When (B) is approx. 102 cm (40 inch)
*(B)=Df – Ds
Get your optimum value (0, 1, 2 . . . 15) dividing (B) by 34.
Note
Depending on the DVD-Audio, the audio may be output with delay
times of 0 ms regardless of the setting.
3
Select “Test Tone” and press ENTER.
The DVD Player outputs a test signal to each speaker when it is
in stop mode. When playing a DVD-Video, it substitutes the
current sound for the test signal.
Press / to select the receiving speakers, and adjust the
volume of each speaker at the same level by pressing / .
If all the volume levels cannot be equalized, adjust them on the
amplifier.
Press ENTER again to turn off the test tone once adjustments
are complete.
49
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p44-55.p65
49
10/2/00, 3:25 PM
Customizing the Function Settings
Explanation of Each Item in the Language Category
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
ENG
Subtitle Language
–––
On-Screen Language
DVD-V
DVD-A
VCD
English: To view on-screen displays in English.
Français: To view on-screen displays in French.
Español: To view on-screen displays in Spanish.
Disc Menu Language
English:
French:
Spanish:
Others:
1
2
3
Audio Language
CD
English:
French:
Spanish:
Others:
DVD-V
To display disc menus in English.
To display disc menus in French.
To display disc menus in Spanish.
To make a further choice.
After pressing ENTER, follow steps 1 - 4 below.
Press /
/ .
To play sound tracks in English.
To play sound tracks in French.
To play sound tracks in Spanish.
To make a further choice.
After pressing ENTER, follow steps 1 - 4 below.
1
Obtain the abbreviation of the preferred language from “Table of
Languages” on page 55.
2
Select the first character by pressing
3
Press /
/ .
Obtain the abbreviation of the preferred language from “Table of
Languages” on page 55.
Select the first character by pressing
Language
/ .
On-Screen Language ENG
English
Disc Menu Language ENG
Audio Language
E S
French
Subtitle Language
Others
Language
English
French
Subtitle Language
Others
–––
Spanish
Note
Depending on the disc, a language recorded on the disc may be given priority
and selected automatically when the disc is loaded regardless of the setting.
Press ENTER.
Note
Some DVD-Video may not include your pre-selected language. In this case,
the DVD Player automatically displays disc menus consistent with the disc’s
initial language setting.
50
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p44-55.p65
50
Spanish
Press ENTER.
Code E S
4
–––
Code E S
4
Disc Menu Language E S
Audio Language
ENG
/ .
to shift and select the second character by pressing
to shift and select the second character by pressing
On-Screen Language ENG
DVD-V
10/2/00, 3:25 PM
Explanation of Each Item in the
Display Category
Display
Subtitle Language
English:
French:
Spanish:
No Subtitles:
Others:
DVD-V
To display subtitles in English.
To display subtitles in French.
To display subtitles in Spanish.
To disable subtitles.
To make a further choice.
After pressing ENTER, follow steps 1 - 4 below.
1
Obtain the abbreviation of the preferred language from “Table of
Languages” on page 55.
2
Select the first character by pressing
3
Press /
/ .
/ .
to shift and select the second character by pressing
Language
On-Screen Language ENG
English
Disc Menu Language ENG
Audio Language
ENG
French
Subtitle Language
Others
AA
On
Background
Screen Saver
Gray
On
On-Screen Displays
Off: Operational modes (e.g. “
On: Operational modes (e.g. “
screen.
”, “
”, “
Background
DVD-V
DVD-A
VCD
CD
”) are not displayed .
”) are displayed on-
DVD-V
DVD-A
VCD
CD
Blue:
Blue background.
Gray:
Gray background.
Capture: To use a picture you sample and store in the memory
using the Capture feature as a background (see page 41).
Jacket: To use the jacket picture included on some discs as a
background. If it is not included, a gray background will
be substituted.
Spanish
Code A A
4
On-Screen Displays
Screen Saver
DVD-V
Press ENTER.
Notes
Off: The screen saver is disengaged.
On: The screen saver operates.
• Some DVD-Video may be set to display subtitles in a different language
than you selected. A prior subtitle language may be programmed on the
disc.
• Some DVD-Video allow you to change subtitle selections only via the disc
menu. If this is the case, Press MENU and choose the appropriate subtitle
language from the selection on the disc menu.
51
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p44-55.p65
51
10/2/00, 3:26 PM
Customizing the Function Settings
Explanation of Each Item in the Operation Category
Operation
Pause/Still
Auto
Parental Lock
Off
Remote Confirmation On
Title/Group Stop
PBC
Off
On
Priority Contents
AUDIO
Pause/Still
Auto:
Frame:
For normal use. Still and fast motion images can be
paused.
The resolution of still pictures is improved, so that you
can make a motionless picture clearer when you pause it.
Parental Lock
DVD-V
DVD-Video equipped with the parental lock function are rated
according to their content. The content allowed by a parental lock
level and the way a DVD-Video can be controlled may vary from
disc to disc. For example, some discs allow you to edit out violent
scenes unsuitable for children and replace them with more suitable
scenes, or lock out playback of the disc altogether.
Note
DVD-Video may or may not respond to the parental lock setting. This is not
a defect in the DVD Player. Make sure this function works with your DVDVideo.
Off: The parental lock feature does not function. After pressing
ENTER, follow step 1 below.
On: To activate the parental lock feature or change the settings.
After pressing ENTER, follow steps 1 - 3 below.
Operation
Pause/Still
1
Press the number buttons to create a personal 4-digit security
code, then press ENTER.
If you make a mistake before pressing the ENTER button, press
CLEAR and enter your 4-digit security code again.
2
Enter the code of an area whose standards were used to rate the
DVD-Video, referring to the list below.
DVD-V
Auto
Off
Parental Lock
Remote Confirmation On
Title/Group Stop
PBC
Off
On
Priority Contents
AUDIO
Area
AUSTRALIA
BELGIUM
CANADA
CHINA
DENMARK
FINLAND
FRANCE
GERMANY
HONG KONG
INDONESIA
ITALY
JAPAN
MALAYSIA
NETHERLANDS
NORWAY
PHILIPPINES
RUSSIAN FEDERATION
SINGAPORE
SPAIN
SWEDEN
SWITZERLAND
TAIWAN
THAILAND
UNITED KINGDOM
UNITED STATES
Code
AU
BE
CA
CN
DK
FI
FR
DE
HK
ID
IT
JP
MY
NL
NO
PH
RU
SG
ES
SE
CH
TW
TH
GB
US
Off
On
Security Code – – – –
/ .
a Select the first character by pressing
b Press / to shift and select the second character by pressing
c Press ENTER.
52
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p44-55.p65
52
10/2/00, 3:26 PM
/ .
3
Press
/
to select the parental lock level, then press ENTER.
Auto
Off
Parental Lock
Remote Confirmation On
Title/Group Stop
PBC
Off
On
Priority Contents
AUDIO
DVD-V
DVD-A
VCD
CD
DVD-V
DVD-A
Off: The beeper does not sound.
On: The beeper sounds with each remote operation.
Operation
Pause/Still
Remote Confirmation
Off
On
Area Code
US
Level
7
Title/Group Stop
You cannot play DVD Video rated higher than the level you selected unless
you cancel the parental lock function.
For example, when you select level 7, discs rated higher than level 7 are
locked out and cannot be played.
The parental lock level is equivalent to the following U.S. movie ratings.
Level 7: NC-17
Level 6: R
Level 4: PG 13
Level 3: PG
Level 1: G
Off: The DVD Player continues after playback of a title/group is
complete.
On: The DVD Player stops after playback of a title/group is
complete.
PBC
VCD
Off: When playing a Video-CD without using the menu.
On: To use the menu when playing a PBC-featured Video-CD.
The parental lock levels for other areas than U.S. are included for future use.
Check the appropriate parental lock level when you buy a DVD-Video
equipped with the parental lock feature in the future.
Priority Contents
To change the parental lock level
Follow step 1 - 3.
1
After selecting “On” or “Off”, press
ENTER.
four times, then press
DVD-A
Select the playback priority between DVD-Video and DVD-Audio
format signals when playing a DVD disc that contains both DVDVideo and DVD-Audio format signals.
DVD-AUDIO:
To change your 4-digit security code
DVD-V
DVD-VIDEO:
DVD Audio format signals take priority over DVD
Video format signals.
DVD Video format signals take priority over DVD
Audio format signals.
The 4-digit security code is cleared.
2
Press the number buttons to create a new 4-digit security code.
3
Press ENTER.
53
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p44-55.p65
53
10/2/00, 3:26 PM
Customizing the Function Settings
Explanation of Each Item in the Operation Category
Initial Setup
On-Screen Language ENG
TV Shape
Audio Out Select
Initial Setup
4:3 LB
Bitsream
DVD-V
DVD-A
VCD
CD
1
Press
/
to select “On-Screen Language”, then press ENTER.
2
Press
/
to select a language, then press ENTER.
For details, see “On-Screen Language” on page 50.
to select “TV Shape”, then press ENTER.
3
Press
4
Press /
ENTER.
to select the aspect ratio of the TV screen, then press
For details, see “TV Shape” on page 46.
5
Press
to select “Audio Out Select”, then press ENTER.
6
Press
/
to select the audio output, then press ENTER.
For details, see “Audio Out Select” on page 48.
7
Finally press SETUP.
54
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p44-55.p65
54
10/2/00, 3:26 PM
Table of Languages
Table of Languages and Their Abbreviations
Abbreviation Language
of the
Language
–––
No alternate
language
CHI (ZH) Chinese
DUT (NL) Dutch
ENG (EN) English
FRE (FR) French
GER (DE) German
ITA (IT)
Italian
JPN (JA)
Japanese
KOR (KO) Korean
MAY (MS) Malay
SPA (ES)
Spanish
AA
Afar
AB
Abkhazian
AF
Afrikaans
AM
Amharic
AR
Arabic
AS
Assamese
AY
Aymara
AZ
Azerbaijani
BA
Bashkir
BE
Belorussian
BG
Bulgarian
BH
Bihari
BI
Bislama
BN
Bengali,Bangla
BO
Tibetan
BR
Breton
CA
Catalan
CO
Corsican
CS
Czech
CY
Welsh
DA
Danish
DZ
Bhutani
EL
Greek
Abbreviation Language
of the
Language
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GL
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
IW
JI
JW
KA
KK
KL
KM
KN
KS
KU
KY
LA
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scottish,Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Kashmiri
Kurdish
Kirghiz
Latin
Abbreviation Language
of the
Language
LN
LO
LT
LV
MG
MI
MK
ML
MN
MO
MR
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
PS
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
Lingala
Laotian
Lithuanian
Latvian,Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto,Pushto
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sango
Serbo-Croatian
Singhalese
Slovak
Abbreviation Language
of the
Language
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tongan
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Zulu
55
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p44-55.p65
55
10/2/00, 3:26 PM
Using the Remote Controller
This section explains how to get the best use out of the supplied remote controller. In addition to being able to
operate the DVD Player, it is also equipped to handle a number of the functions of an Onkyo receiver. The remote
controller can also be se up to “learn” a number of remote commands to control the components of other
manufacturers.
Using the remote controller to operate the DVD player
Before attempting to operate the DVD Player, press DVD to set the
remote controller to operate the DVD Player. The following
buttons can be used to operate the DVD Player. Refer to the pages
in brackets [ ] for details on each function.
SEND/LEARN indicator [58]
Lights when the remote controller is sending a command to the DVD
Player or other preprogrammed component, and when learning the
command of another remote control unit.
ON/STNBY buttons [17]
Press ON to turn the DVD Player on and STNBY to put the DVD
Player in standby. (The STANDBY indicator lights up.)
V.OFF (TV ON/OFF) button [43]
Press to turn off the video output circuitry for a more dedicated audio
performance. This button can also be used to learn the commands to
turn your TV or monitor on and off.
DVD button [58]
Press to select the DVD mode. In this mode, the remote controller is set
to control the DVD Player.
ANGLE button [32]
Press repeatedly to select a camera angle when a DVD-Video is
recorded with multiple angle playback.
AUDIO button [34]
Press repeatedly to select an audio and/or language track recorded on a
DVD-Audio/Video.
TOP MENU button [18]
Press to select the top menu on a DVD-Audio/Video. This menu may
be the same as the DVD menu.
ZOOM (CH) +/– buttons [30]
When the Zoom function is turned on, use these buttons to enlarge and
reduce the screen image.
RETURN button [18]
Press to go back to a previous menu screen.
ZOOM ON button [30]
Press to turn the Zoom function on and off.
PROGRESSIVE button [42]
Press to select progressive scan from the DVD Player.
(skip back) button [26]
Press to return to previous titles, groups, chapters, or tracks.
(play) button [20]
Press to start playback.
(fast reverse) button [22]
Press to scan rapidly backward through the contents on a disc.
(stop) button [21]
Press to stop playback.
SLOW
button [22]
Press to perform slow reverse playback of a DVD.
DIMMER button [16]
Press repeatedly to change the brightness of the front panel display in
four grades (including turning the front panel display off).
The dimmer setting is restored to normal brightness whenever the DVD
Player is turned off.
RANDOM button [29]
Press to start random playback.
CLEAR button [25-30]
Press to clear entered values and settings.
STILL +/– buttons [22]
When still pictures have been recorded on a DVD-Audio, use these
buttons to select the picture.
56
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p56-60.p65
56
10/2/00, 3:26 PM
Remote controller buttons that can be
used to control your Onkyo receiver
Number buttons [24, 28]
Use to enter numeric values.
SUBTTL button [33]
Press repeatedly to select one of the subtitle languages recorded on a
DVD-Video.
button [21]
Press to open and close the disc tray.
MENU button [18]
Press to display the DVD menu.
/ / / and ENTER multi control [18]
Use to navigate menu screens and enter settings.
SETUP button [18]
Press to display the Setup screen menu.
QUICK button [37]
Press to display the Quick list of functions relevant to the current
playback mode.
V.REMOTE button [36]
Press to display the Virtual Remote on the screen.
(skip forward) button [26]
Press to advance through titles, groups, chapters, or tracks.
(fast forward) button [22]
Press to scan rapidly forward through the contents on a disc.
SLOW
button [22]
Press to perform slow forward playback of a DVD or Video CD.
Press RECVR to set the remote controller to operate an Onkyo
receiver. The following buttons can be used to operate an Onkyo
receiver. Refer to the manual supplied with your receiver for
details on each function.
PAUSE/STEP
button [21]
Press to playback. Pressing repeatedly causes the still video image to be
advanced a single frame at a time.
DISPLAY/NAVI button [38]
Press to display the on-screen navigational.
MEMORY button [28]
Press to playback titles, chapters, or tracks in a specific order.
REPEAT button [27]
Press to repeat playback.
DNR button [31]
Press repeatedly to select one of the digital noise reduction processes
for a clearer video presentation.
A-B button [27]
Press to repeat a specific section on a disc.
SEARCH button [25]
Press to find the specific section on a disc where you want to start
playback.
ON/STNBY buttons
Press ON to turn the receiver on and STNBY to put the receiver in
standby. Depending on the receiver, pressing ON may alternately turn
the receiver on and put it in standby.
RECVR button
Press to select the Receiver mode. In this mode, the remote controller is
set to control an Onkyo receiver. This button also can be used in DVD
mode.
Input selector buttons
Press to select the input. This button also can be used in DVD mode.
VOL / buttons
Press to adjust the volume. These buttons can also be programmed to
adjust the volume of other components.
MUTING button
Press to mute the audio output.
PRESET / buttons
Press to select the radio presets if the receiver has radio features.
57
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p56-60.p65
57
10/2/00, 3:26 PM
Programming the Commands of Other Remote
Control Units into the Remote Controller
This remote controller features a learning function that allows you to program the remote codes of other remote
control units for more singular control of your home entertainment system. A number of commands can be
programmed for operation for when the remote controller is in DVD mode and when it is in Receiver mode. Please
follow the procedure in this section to program your remote controller to your preferences.
Programming procedure
The first step in the procedure is to determine whether the new command is to be learned in the DVD mode or in the Receiver mode.
Generally speaking, this should be decided by the command being learned. After deciding which mode is to be used, you will then transfer the
individual commands from the other remote control unit to the RC-438DV remote controller one at a time. Each command is then
programmed to one of the available buttons on the RC-438DV remote controller.
Even after the commands have been programmed, keep the other remote control unit in a safe place in the case that the programmed
commands should be lost (e.g., when the batteries run down). If the commands are lost, it will then be necessary to program them again.
1
Place the remote controller and the
other remote control unit of the
other component facing each other
at a distance of 5 to 15 cm (2 to 6
inches) apart.
2
While pressing and holding down
the desired MODE button (DVD or
RECVR) on the remote controller,
press SEARCH and then release
both buttons.
When you press and hold down the desired MODE
button, the SEND/LEARN indicator lights up. When
you press SEARCH, the indicator turns off. When
you release both buttons, the indicator lights up
again.
3
5 to 15 cm
(2 to 6
inches)
RC-438DV
SEND/LEARN
indicator
DVD
Press and release the button on the
remote controller to which you
want to transfer the new command.
The buttons that can be selected in this step depend
on the mode. Refer to the shaded areas in the
illustrations below to determine what buttons can be
programmed in each mode.
If you press the wrong button by mistake, press that
same button again. The SEND/LEARN indicator
flashes three times and the remote controller exits the
programming mode. When this is the case, start
again at step 1.
DVD MODE
RECVR
ENTER
RECEIVER MODE
SEARCH
: Buttons that can be programmed.
58
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p56-60.p65
58
10/2/00, 3:26 PM
4
Notes
Press and hold down the button on
the other remote control unit that
corresponds to the command you
want to program until the SEND/
LEARN indicator flashes twice to
indicate that the command has
been successfully programmed.
After flashing twice, the SEND/LEARN indicator
lights up again.
5
Repeat steps 3 and 4 to program
other commands within the same
mode.
Repeat step 2 to 4 to program
commands to the other mode.
6
Press the MODE button (DVD or
RECVR) that you pressed in step 2
to complete the programming.
7
Use the remote controller to
perform the newly learned
command to confirm that it was
learned correctly.
• Some buttons have already been programmed to control functions of an
Onkyo receiver. Therefore, it is recommended to program additional
functions of the receiver that are not already programmed in the remote
controller.
• If no buttons are pressed for more than 30 seconds during the
programming, or if you perform an invalid operation, the SEND/LEARN
indicator flashes three times quickly and the remote controller exits the
programming mode. Resume programming from step 2.
• If you perform an invalid operation during programming, the SEND/
LEARN indicator flashes three times quickly and the remote controller
exits the programming mode. Resume from Step 2.
• When you want to program a command to a button to which you have
already programmed a command, simply follow the same procedure and
programming for that button will be overwritten.
• The remote controller uses infrared rays to send its commands, as do most
other remote control units. Though most remote control units can be
memorized by the remote controller, be aware that some remote control
units use a system that is quite different from the remote controller and
therefore may not be able to be programmed.
• Some remote control units have a single button that performs multiple
functions (for example, the function may change each time the button is
pressed). If this is the case, each function must be programmed to a
separate button on the remote controller.
• Once you have programmed the commands from the other remote control
unit, refer to the instructions supplied with the other component to operate.
• Make sure that both the remote controller and the other remote control unit
have new batteries. If either of them has batteries that are low, you may not
be able to program the commands of the other remote control unit properly
into the remote controller.
• After programming another function to the ZOOM ON button or ZOOM
+/– buttons, it is no longer possible to perform the Zoom function. To use
the Zoom function again, it is necessary to erase the commands
programmed to those buttons. For details, see page 60.
• Removing the batteries from the remote controller for at least 10 minutes
erases all of the commands that have been programmed in the remote
controller.
59
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p56-60.p65
59
10/2/00, 3:26 PM
Programming the Commands of Other Remote
Control Units into the Remote Controller
SEND/LEARN
indicator
DVD
RECVR
SEARCH
Erasing the programmed command
from one button
Erasing all the commands
programmed under a MODE button
You can only erase memorized commands and not preset ones.
1
2
Press and hold down the desired
MODE button for the command,
press the SEARCH button, and
then release both buttons.
Press and hold down the desired
MODE button, press the SEARCH
button twice, and then release both
buttons.
When you release the buttons, the SEND/LEARN
indicator lights.
When you release the buttons, the SEND/LEARN
indicator flashes twice slowly and then lights again.
Press and release the button for
the command you wish to erase.
Press and release the same MODE
button again.
When you press the button, the SEND/LEARN
indicator turns off. When you release the button, the
lamp lights again.
3
1
Press and release the same button
again.
The SEND/LEARN lamp flashes twice. The
memorized command is erased.
Note
If no button is pressed for more than 30 seconds during the programming, the
SEND/LEARN indicator flashes three times quickly, and the remote
controller exits the programming mode. Resume from Step 1.
2
When you release the button, the SEND/LEARN
indicator flashes twice slowly. This erases all the
commands memorized to the MODE button.
Notes
• If no button is pressed for more than 30 seconds, the SEND/LEARN
indicator flashes three times quickly and the remote controller exits the
programming mode. Resume Step 1.
• If you perform an invalid operation during programming, the SEND/
LEARN indicator flashes three times quickly and the remote controller
exits the programming mode. Resume from Step 1.
• If many commands have been programmed to the MODE button, then the
SEND/LEARN indicator may remain lit for some time during Step 2. This
is not a malfunction.
60
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p56-60.p65
60
10/2/00, 3:26 PM
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service. Refer also to the respective instruction manuals of the
connected components and TV.
Symptoms
Causes
Remedies
Pages
The DVD Player doesn’t
switch on.
• The power cord is disconnected.
• The main power is set to OFF.
• There is external noise in the computer
circuits of the DVD Player.
• Check the connection of the power cord.
• Turn on the main power.
• Switch off the main power, then switch it on
again. If not recovered, disconnect the power
cord, then connect it again.
• Contact your nearest Onkyo service center.
17
17
17
• Insert a disc. (Check that “DVD,” “VCD,” or
“CD” is lit in the DVD Player’s display).
• See “1. Regional Restriction Codes (Region
Number)” on page 4.
• Check the playable discs.
• Place the disc with the playback side down.
• Place the disc within the proper guide on the
disc tray.
• Eject the disc and clean it.
• Deactivate the parental lock function or
change the parental lock level.
20
• The AC fuse is blown.
The DVD Player doesn’t start
playback.
• No disc is inserted.
DVD Player
• The region number of the disc does not match
that of the DVD Player.
• An unplayable disc is inserted.
• The disc is placed upside down.
• The disc is not placed within the disc tray
guide.
• The disc is dirty.
• The parental lock function is activated.
4
6
20
20
6
52
Brightness is unstable or noise
is visible on the playback
picture.
• Copy protection is activated.
• Connect the DVD Player directly to the TV.
Avoid connecting the DVD Player to the TV
through a VCR.
10
The playback picture is
occasionally distorted.
• The disc is dirty.
• It is in fast forward or fast reverse playback.
• Eject the disc and clean it.
• Sometimes a small amount of picture
distortion may appear. This is not a
malfunction.
6
–
Playback doesn’t follow the
course of the disc’s programs.
• The DVD Player is in repeat playback mode,
memory playback mode, or random playback
mode, etc.
• Resume normal playback.
27-29
The picture from the DVD
Player doesn’t appear on the
TV screen.
• The TV is not set to receive the output signals
from the DVD Player.
• The DVD Player is not properly connected.
• The video output circuitry has been switched
off.
• Set the TV to the DVD Player’s input.
10
• Check the connections to the DVD Player.
• Turn the video circuitry on.
10
43
No sound or inaccurate sound
is reproduced.
• A wrong sound signal conversion method
(Audio Out Select) is selected.
• Check the current sound signal conversion
35, 48
method, and select the right setting for “Audio
Out Select”. Also refer to “Output Sound
Conversion Table” on page 35.
• Set the TV to the DVD Player’s input.
• The TV is not set to receive the output signals
from the DVD Player.
• The DVD Player is not properly connected.
Remote Controller
–
• Check the connections to the DVD Player.
10-13
The buttons on the remote
controller and DVD Player do
not operate.
• Power supply fluctuations or other
abnormalities such as static electricity may
interrupt correct operation.
• Switch off the main power, then switch it on
again. If not recovered, disconnect the power
cord, then connect it again.
17
The buttons on the DVD
Player operate but the buttons
on the remote controller do
not operate.
• No batteries are inserted in the remote
controller.
• The batteries are worn out.
• The remote controller is not pointed at the
remote sensor of the DVD Player.
• The remote controller is too far from the DVD
Player.
• Insert new batteries.
9
• Replace with new batteries.
• Point the remote controller at the remote
sensor of the DVD Player.
• Operate the remote controller within 5 m (16
feet).
9
9
• The remote controller is not aimed at the other
component.
• The mode selection is incorrect.
• Aim the remote controller at the component
you wish to operate.
• Check that the mode is correct for the
command you are attempting.
• Reprogram the command into the remote
controller.
58
Learned functions of the
remote controller do not work.
• Learning was not successful.
9
58
58
Because the unit contains a microcomputer to provide advanced functions, it may malfunction due to external noise or static electricity. If
this happens, press the POWER switch on the unit and then press it again after about five seconds.
61
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p61-64.p65
61
10/2/00, 3:26 PM
Specifications
DVD Player
Power supply
AC 120 V, 60 Hz
Power consumption
45 W
Weight
11.0 kg, 24.3 lbs
External dimensions
435 x 122 x 374 mm (W/H/D), 17 1/8" x 4 13/16" x 14 3/4" (W/H/D)
Signal system
NTSC/PAL*
Laser
Semiconductor laser, wavelength 650/780 nm
Frequency range (digital audio)
DVD linear sound:
Signal-to-noise ratio (digital audio)
More than 112 dB
Audio dynamic range (digital audio)
More than 106 dB
Harmonic distortion (digital audio)
Less than 0.002 %
Wow and flutter
Below measurable level (less than ±0.001 % (W.PEAK))
Operating conditions
Temperature: 5°C to 35°C (41°F to 95°F), Operation status: Horizontal
48 kHz sampling 4 Hz to 22 kHz
96 kHz sampling 4 Hz to 44 kHz
192 kHz sampling 4 Hz to 96 kHz
* Not applicable for USA and Canadian models
Outputs
Video output
1.0 V (p-p), 75 Ω, negative sync., pin jack × 2
S-video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin × 2
(C) 0.286 V (p-p), 75 Ω
Component video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., pin jack × 2
(PB)/(PR) 0.7 V (p-p), 75 Ω, pin jack × 4
Audio output (digital output Optical)
Optical connecter × 2
Audio output (digital output Coaxial)
0.5 V (p-p), 75 Ω, pin jack × 2
Audio output (2-Channel Audio)
2.0 V (rms), 320 Ω, pin jack (L, R) × 2
Audio output (5.1-Channel Surround)
2.0 V (rms), 320 Ω, pin jack × 6
2.0 V (rms), 320 Ω, DB25 × 1
Supplied Accessories
Audio/video connection cable
1
Remote controller (RC-438DV)
1
Batteries (size AA/UM-3)
2
Power cord
1
S-video cable
1
DB-25 cable
1
Specifications and features are subject to change without notice.
62
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p61-64.p65
62
10/2/00, 3:26 PM
63
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p61-64.p65
63
10/2/00, 3:26 PM
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8111 Fax: 072-833-5222
ONKYO U.S.A. CORPORATION
200 Williams Drive, Ramsey, N.J. 07446, U.S.A.
Tel: 201-825-7950 Fax: 201-825-8150 E-mail: [email protected]
ONKYO EUROPE ELECTRONICS GmbH
Industriestrasse 20, 82110 Germering, GERMANY
Tel: 089-849-320 Fax: 089-849-3265 E-mail: [email protected]
ONKYO CHINA LIMITED
Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
Printed in Japan
W0008-1
SN 29343012
Downloaded
From Disc-Player.com Onkyo Manuals
DV-S939(US_E)p61-64.p65
64
HOMEPAGE
http://www.onkyo.co.jp/
10/2/00, 3:26 PM
E
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement