Gestetner MP3500SP Printers User Guide Manual Pdf

Gestetner MP3500SP Printers User Guide Manual Pdf
Operating Instructions
General Settings Guide
1
Connecting the Machine
2
System Settings
3
Copier / Document Server Features
4
Facsimile Features
5
Printer Features
6
Scanner Features
7
Registering Addresses and Users for Facsimile/Scanner Functions
8
Other User Tools
9
Appendix
Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the
Safety Information in "About This Machine" before using the machine.
Downloaded from ManualsPrinter.com Manuals
Introduction
This manual contains detailed instructions and notes on the operation and use of this machine. For your
safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy
place for quick reference.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.
Notes:
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
Depending on which country you are in, certain units may be optional. For details, please contact your
local dealer.
Caution:
Use of controls or adjustments or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
Notes:
The model names of the machines do not appear in the following pages. Check the type of your machine before reading this manual.
•
Type 1: 35 copies/minute (A4K, 81/2"×11"K)
•
Type 2: 45 copies/minute (A4K, 81/2"×11"K)
Certain types might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the metric version.
Downloaded from ManualsPrinter.com Manuals
Manuals for This Machine
Refer to the manuals that are relevant to what you want to do with the machine.
Important
❒ Media differ according to manual.
❒ The printed and electronic versions of a manual have the same contents.
❒ Adobe Acrobat Reader/Adobe Reader must be installed in order to view the
manuals as PDF files.
❒ Depending on which country you are in, there may also be html manuals. To
view these manuals, a Web browser must be installed.
❖ About This Machine
Be sure to read the Safety Information in this manual before using the machine.
This manual provides an introduction to the functions of the machine. It also
explains the control panel, preparation procedures for using the machine,
how to enter text, and how to install the CD-ROMs provided.
❖ General Settings Guide
Explains User Tools settings, and Address Book procedures such as registering fax numbers, e-mail addresses, and user codes. Also refer to this manual
for explanations on how to connect the machine.
❖ Troubleshooting
Provides a guide to solving common problems, and explains how to replace
paper, toner, and other consumables.
❖ Security Reference
This manual is for administrators of the machine. It explains security functions that the administrators can use to protect data from being tampered, or
prevent the machine from unauthorized use.
Also refer to this manual for the procedures for registering administrators, as
well as setting user and administrator authentication.
❖ Copy/ Document Server Reference
Explains Copier and Document Server functions and operations. Also refer to
this manual for explanations on how to place originals.
❖ Facsimile Reference
Explains Facsimile functions and operations.
❖ Printer Reference
Explains Printer functions and operations.
❖ Scanner Reference
Explains Scanner functions and operations.
Downloaded from ManualsPrinter.com Manuals
i
❖ Network Guide
Explains how to configure and operate the machine in a network environment, and use the software provided.
This manual covers all models, and includes descriptions of functions and
settings that might not be available on this machine. Images, illustrations, and
information about operating systems that are supported might also differ
slightly from those of this machine.
❖ Other manuals
• Manuals for This Machine
• Safety Information
• Quick Reference Copy Guide
• Quick Reference Fax Guide
• Quick Reference Printer Guide
• Quick Reference Scanner Guide
• PostScript3 Supplement
• UNIX Supplement
• Manuals for DeskTopBinder Lite
DeskTopBinder Lite Setup Guide
DeskTopBinder Introduction Guide
Auto Document Link Guide
Note
❒ Manuals provided are specific to machine types.
❒ For "UNIX Supplement", please visit our Web site or consult an authorized
dealer.
❒ "PostScript3 Supplement" and "UNIX Supplement" include descriptions of
functions and settings that might not be available on this machine.
Product name
General name
DeskTopBinder Lite and DeskTopBinder Professional*1
DeskTopBinder
ScanRouter EX Professional*1 and ScanRouter
EX Enterprise*1
the ScanRouter delivery software
*1 Optional
iiDownloaded from ManualsPrinter.com Manuals
TABLE OF CONTENTS
Manuals for This Machine ......................................................................................i
How to Read This Manual .....................................................................................1
Symbols .....................................................................................................................1
Display Panel..........................................................................................................2
Accessing User Tools ...........................................................................................3
Changing Default Settings .........................................................................................3
Quitting User Tools ....................................................................................................4
Menu Protect..............................................................................................................4
1. Connecting the Machine
Connecting to the Interfaces ................................................................................5
Connecting to the Ethernet Interface .........................................................................6
Connecting to the USB Interface................................................................................8
Connecting to the IEEE 1284 Interface......................................................................9
Connecting to the IEEE 802.11b (Wireless LAN) Interface......................................10
Network Settings..................................................................................................13
Settings Required to Use the Printer/LAN-Fax ........................................................13
Settings Required to Use Internet Fax .....................................................................15
Settings Required to Use E-mail Function ...............................................................19
Settings Required to Use Scan to Folder Function ..................................................22
Settings Required to Use the Network Delivery Scanner.........................................24
Settings Required to Use Network TWAIN Scanner ................................................26
Settings Required to Use Document Server ............................................................28
Using Utilities to Make Network Settings .................................................................30
Connecting the Machine to a Telephone Line and Telephone ........................38
Connecting the Telephone Line ...............................................................................38
Selecting the Line Type............................................................................................39
2. System Settings
General Features..................................................................................................41
Output tray settings ..................................................................................................43
Tray Paper Settings .............................................................................................44
Timer Settings ......................................................................................................47
Interface Settings.................................................................................................49
Network ....................................................................................................................49
Parallel Interface ......................................................................................................52
IEEE 802.11b ...........................................................................................................53
Print List ...................................................................................................................54
File Transfer .........................................................................................................55
Administrator Tools.............................................................................................62
Program / Change / Delete LDAP Server ................................................................69
Programming the LDAP server ................................................................................70
Downloaded from ManualsPrinter.com Manuals
iii
3. Copier / Document Server Features
General Features..................................................................................................75
Reproduction Ratio..............................................................................................80
Edit ........................................................................................................................82
Stamp ....................................................................................................................87
Background Numbering ...........................................................................................87
Preset Stamp ...........................................................................................................87
User Stamp ..............................................................................................................88
Date Stamp ..............................................................................................................89
Page Numbering ......................................................................................................90
Input/Output .........................................................................................................91
Settings for the Document Server......................................................................93
4. Facsimile Features
General Settings/Adjustment..............................................................................95
Reception Settings ..............................................................................................99
E-mail Settings ...................................................................................................101
IP-Fax Settings ...................................................................................................103
Administrator Tools........................................................................................... 107
Registering Fax Information .............................................................................115
Registering Fax Information ...................................................................................116
Changing Fax Information......................................................................................119
Deleting Fax Information ........................................................................................119
Storing, Changing, and Deleting an Auto Document ..................................... 120
Storing and Changing an Auto Document..............................................................120
Deleting an Auto Document ...................................................................................122
Programming Changing and Deleting a Scan Size......................................... 123
Deleting a Scan Size..............................................................................................124
Forwarding ......................................................................................................... 125
Programming an End Receiver ..............................................................................126
Quitting the Forwarding Function ...........................................................................127
Forwarding Mark ....................................................................................................128
Parameter Settings ............................................................................................ 129
Changing the User Parameters..............................................................................134
Printing the User Parameter List ............................................................................135
Special Senders to Treat Differently ................................................................136
Authorized Reception.............................................................................................138
Forwarding .............................................................................................................139
Reception File Print Quantity .................................................................................139
Print 2 Sided...........................................................................................................140
Memory Lock..........................................................................................................140
Paper Tray .............................................................................................................140
Programming/Changing Special Senders ..............................................................141
Programming Initial Set Up of a Special Sender....................................................146
Deleting a Special Sender......................................................................................149
Printing the Special Sender List .............................................................................149
iv
Downloaded from ManualsPrinter.com Manuals
Box Settings ....................................................................................................... 150
Programming/Changing Personal Boxes ...............................................................151
Deleting Personal Boxes........................................................................................154
Programming/Changing Information Boxes ...........................................................155
Deleting Information Boxes ....................................................................................157
Programming/Changing Transfer Boxes................................................................158
Deleting Transfer Boxes.........................................................................................162
Printing the Box List ...............................................................................................163
Storing or Printing Received Documents........................................................164
Reception Report e-mail ........................................................................................165
5. Printer Features
List / Test Print ...................................................................................................167
Printing the Configuration Page .............................................................................168
Maintenance ....................................................................................................... 170
System ................................................................................................................ 171
Host Interface ..................................................................................................... 174
PCL Menu ...........................................................................................................175
PS Menu.............................................................................................................. 177
PDF Menu ...........................................................................................................178
6. Scanner Features
Scan Settings ..................................................................................................... 179
Destination List Settings................................................................................... 182
Send Settings ..................................................................................................... 183
7. Registering Addresses and Users for Facsimile/Scanner Functions
Address Book..................................................................................................... 187
Managing names in the Address Book ..................................................................190
Sending fax by Quick Dial ......................................................................................190
Sending e-mail by Quick Dial .................................................................................190
Sending scanned files to a shared folder directly...................................................191
Preventing unauthorized user access to shared folders from the machine ...........191
Managing users and machine usage .....................................................................191
Registering Names ............................................................................................ 192
Registering Names.................................................................................................192
Changing a Registered Name................................................................................194
Deleting a Registered Name ..................................................................................195
Authentication Information ............................................................................... 196
Registering a User Code........................................................................................197
Changing a User Code...........................................................................................198
Deleting a User Code.............................................................................................199
Displaying the Counter for Each User....................................................................200
Printing the Counter for Each User ........................................................................201
Printing the Counter for All Users...........................................................................202
Clearing the Number of Prints................................................................................203
Fax Destination ..................................................................................................204
Fax Destination ......................................................................................................206
IP-Fax Destination..................................................................................................212
Downloaded from ManualsPrinter.com Manuals
v
E-mail Destination.............................................................................................. 217
Registering an E-mail Destination..........................................................................217
Changing an E-mail Destination.............................................................................219
Deleting an E-mail Destination...............................................................................220
Registering Folders ........................................................................................... 221
Using SMB to Connect...........................................................................................221
Using FTP to Connect............................................................................................227
Using NCP to Connect ...........................................................................................233
Registering Names to a Group ......................................................................... 239
Registering a Group ...............................................................................................239
Registering Names to a Group...............................................................................240
Adding a Group to Another Group .........................................................................241
Displaying Names Registered in a Group ..............................................................242
Removing a Name from a Group ...........................................................................243
Deleting a Group Within Another Group ................................................................244
Changing a Group Name .......................................................................................245
Deleting a Group ....................................................................................................246
Registering a Protection Code ......................................................................... 247
Registering a Protection Code to a Single User.....................................................247
Registering a Protection Code to a Group User.....................................................249
Registering the Transfer Request .................................................................... 250
Registering a Transfer Station / Receiving Station ................................................251
Changing a Transfer Station / Receiving Station ...................................................254
Deleting a Transfer Station / Receiving Station .....................................................257
Registering SMTP and LDAP Authentication.................................................. 258
SMTP Authentication .............................................................................................258
LDAP Authentication ..............................................................................................259
8. Other User Tools
Changing the Display Language ...................................................................... 261
Inquiry ................................................................................................................. 262
Counter ............................................................................................................... 263
Displaying the Total Counter..................................................................................263
9. Appendix
Copyrights ..........................................................................................................265
expat ......................................................................................................................265
NetBSD ..................................................................................................................266
Sablotron................................................................................................................268
JPEG LIBRARY .....................................................................................................268
SASL ......................................................................................................................269
MD4........................................................................................................................270
MD5........................................................................................................................270
Samba(Ver 3.0.4)...................................................................................................271
RSA BSAFE® .........................................................................................................271
Open SSL...............................................................................................................272
Open LDAP ............................................................................................................277
INDEX....................................................................................................... 279
vi
Downloaded from ManualsPrinter.com Manuals
How to Read This Manual
Symbols
This manual uses the following symbols:
Indicates important safety notes.
Ignoring these notes could result in serious injury or death. Be sure to read these
notes. They can be found in the "Safety Information" section of About This Machine.
Indicates important safety notes.
Ignoring these notes could result in moderate or minor injury, or damage to the
machine or to property. Be sure to read these notes. They can be found in the
"Safety Information" section of About This Machine.
Indicates points to pay attention to when using the machine, and explanations
of likely causes of paper misfeeds, damage to originals, or loss of data. Be sure
to read these explanations.
Indicates supplementary explanations of the machine’s functions, and instructions on resolving user errors.
This symbol is located at the end of sections. It indicates where you can find further relevant information.
[]
Indicates the names of keys that appear on the machine’s display panel.
{}
Indicates the names of keys on the machine’s control panel.
Downloaded from ManualsPrinter.com Manuals
1
Display Panel
The display panel shows machine status, error messages, and function menus.
The function items displayed serve as selector keys. You can select or specify an
item by lightly pressing them.
When you select or specify an item on the display panel, it is highlighted like
. Keys appearing as
cannot be used.
Important
❒ A force or impact of more than 30 N (about 3 kgf) will damage the display
panel.
To display the following screen, press the {User Tools/Counter} key to display the
User Tools menu, and then press [System Settings].
Using the System Settings menu screen as an example, this section explains how
to use the machine’s display panel.
ARM002S
1. The menu tabs for various settings appear. To display the setting
you want to specify or change, press
the appropriate menu tab.
2. A list of settings appears. To specify or change a setting, press the appropriate key in the list.
3. Press this to quit the User Tools
menu.
2Downloaded from ManualsPrinter.com Manuals
Accessing User Tools
This section describes how to access User Tools menu.
User Tools allow you to change or set defaults.
Note
❒ Operations for system settings differ from normal operations. Always quit
User Tools when you have finished.
❒ Any changes you make with User Tools remain in effect even if the main
power switch or operation switch is turned off, or the {Energy Saver} or {Clear
Modes} key is pressed.
❒ Default settings are shown in bold type.
Reference
p.4 “Quitting User Tools”
Changing Default Settings
This section describes how to change the settings of User Tools.
Important
❒ If Administrator Authentication Management is specified, contact your administrator.
A Press the {User Tools/Counter} key.
ZCAS100E
B Select the menu.
To change the System Settings, press [System Settings].
To change the Copier / Document Server Features, press [Copier / Document
Server Features].
To change the Facsimile Features, press [Facsimile Features].
To change the Printer Features, press [Printer Features].
To change the Scanner Features, press [Scanner Features].
To change the language used on the display, press [Français].
To check the telephone numbers to contact for repairs, or to order consumables, press [Inquiry].
To check the counter, press [Counter].
C Select the user tool you want to change.
Downloaded from ManualsPrinter.com Manuals
3
D Change settings by following instructions on the display, and then press
[OK].
Note
❒ To cancel changes made to settings and return to the initial display, press
the {User Tools/Counter} key.
Reference
p.41 “System Settings”
p.75 “Copier / Document Server Features”
p.95 “Facsimile Features”
p.167 “Printer Features”
p.179 “Scanner Features”
p.261 “Other User Tools”
Quitting User Tools
This section describes how to end User Tools.
A Press the {User Tools/Counter} key.
ZCAS100E
Note
❒ You can also quit User Tools by pressing [Exit].
Menu Protect
Using Menu Protect, you can prevent unauthenticated users from changing the
user tools. Menu Protect can be specified for each of the following user tools
menus.
• Copier / Document Server Features
• Facsimile Features
• Printer Features
• Scanner Features
For details, consult your administrator.
4Downloaded from ManualsPrinter.com Manuals
1. Connecting the Machine
This chapter describes how to connect the machine to the network and specify
the network settings.
Connecting to the Interfaces
This section describes how to identify the machine’s interface and connect the
machine according to the network environment.
ATX002S
1. IEEE 1284 port (optional)
4. Wireless LAN port (optional)
Port for connecting the IEEE 1284 interface cable
Port for using the wireless LAN
2. USB2.0 port
Port for connecting the USB2.0 interface
cable
3. 10BASE-T/100BASE-TX port
Port for connecting the 10BASE-T or
100BASE-TX cable
Downloaded from ManualsPrinter.com Manuals
Note
❒ You cannot install two or more of the
options below: IEEE 802.11b wireless
LAN board, IEEE 1284 Interface
Board, Bluetooth, file format converter.
5
Connecting the Machine
Connecting to the Ethernet Interface
1
This section describes how to connect 10BASE-T or 100BASE-TX cable to the
Ethernet interface.
Important
❒ If the main power switch is on, turn it off.
A Attach the supplied ferrite core to the end of the Ethernet cable.
AJL014S
B Make sure the main power switch of the machine is off.
C Connect the Ethernet interface cable to the 10BASE-T/100BASE-TX port.
AJL019S
D Connect the other end of the Ethernet cable to a network connection device
such as a hub.
6Downloaded from ManualsPrinter.com Manuals
Connecting to the Interfaces
E Turn on the main power switch of the machine.
1
AME005S
A
B
Indicator (green)
Lights up green when the machine is connected correctly to the network.
Indicator (yellow)
Lights up yellow when 100 BASE-TX is in operation. Goes off when 10
BASE-T is in operation.
Note
❒ For details about installing the printer driver, see "Preparing the Machine",
Printer Reference.
Reference
"Turning On the Power", About This Machine
"Preparing the Machine", Printer Reference
Downloaded from ManualsPrinter.com Manuals
7
Connecting the Machine
Connecting to the USB Interface
1
This section describes how to connect the USB2.0 interface cable to the USB2.0
port.
A Connect the USB2.0 interface cable to the USB2.0 port.
AJL003S
B Connect the other end to the USB2.0 port on the host computer.
Note
❒ This machine does not come with a USB interface cable. Make sure you
purchase the appropriate cable for the machine and your computer.
❒ The USB2.0 interface board is supported by Windows Me / 2000 / XP, Windows Server 2003, Mac OS X 10.3.3 or higher.
• For Windows Me:
Make sure to install “USB Printing Support". When used with Windows
Me, only a speed equal to that of USB1.1 is possible.
• For Mac OS:
To use Macintosh, the machine must be equipped with the PostScript 3
option. When used with Mac OS X 10.3.3 or higher, a transfer speed of
USB2.0 is supported.
❒ For details about installing the printer driver, see "Preparing the Machine",
Printer Reference.
Reference
"Preparing the Machine", Printer Reference
8Downloaded from ManualsPrinter.com Manuals
Connecting to the Interfaces
Connecting to the IEEE 1284 Interface
This section describes how to connect the IEEE 1284 interface cable to the IEEE
1284 interface board.
1
A Make sure the main power switch on the machine is off.
B Turn off the main power switch of the host computer.
C Connect the IEEE 1284 interface cable to the IEEE 1284 port.
AJL004S
D Connect the other end of the cable into the interface connector on the host
computer.
Check the shape of the connector to the computer. Connect the cable firmly.
E Turn on the main power switch of the machine.
F Turn on the host computer.
When using Windows 95/98/Me/2000/XP and Windows Server 2003, a
printer driver installation screen might appear when the computer is turned
on. If this happens, click [Cancel] on the screen.
Note
❒ For details about installing the printer driver, see "Preparing the Machine",
Printer Reference.
Reference
"Turning On the Power", About This Machine
"Preparing the Machine", Printer Reference
Downloaded from ManualsPrinter.com Manuals
9
Connecting the Machine
Connecting to the IEEE 802.11b (Wireless LAN) Interface
This section describes how to connect to the IEEE 802.11b (wireless LAN) interface.
1
Note
❒ Check the settings of the IP address and subnet mask of this machine.
❒ For details about how to set the IP address and subnet mask from the control
panel of the machine, see "Interface Settings".
❒ Before using this machine with an IEEE 802.11b (Wireless LAN) connection,
you must select [IEEE 802.11b] in [LAN Type].
Reference
p.49 “Network”
Setup Procedure
This section describes how to setup IEEE 802.11b (wireless LAN) interface.
Set up IEEE 802.11b (wireless LAN) according to the following procedure:
ARH007S
10
Downloaded from ManualsPrinter.com Manuals
Connecting to the Interfaces
Note
❒ Select [802.11 Ad hoc] mode when connecting Windows XP as a wireless LAN
client using Windows XP standard driver or utilities, or when not using the
infrastructure mode.
1
❒ For details about how to specify wireless LAN settings from the control panel
on the machine, see "IEEE 802.11b".
❒ For details about how to specify wireless LAN settings from other than the
control panel on the machine, see "Using Utilities to Make Network Settings".
❒ For details about the setting items, see "IEEE 802.11b".
Reference
p.53 “IEEE 802.11b”
p.30 “Using Utilities to Make Network Settings”
Checking the Connection
This section describes how to check the wireless LAN connection.
Make sure the LED of the IEEE 802.11b interface unit is lit.
❖ When using in infrastructure mode
ZGDH600J
1. If it is connected properly to the network, the LED is green when in infrastructure mode. If the LED is blinking, the machine is searching for devices.
2. If [LAN Type] on the [Interface Settings] / [Network] screen is not set to [IEEE
802.11b], it does not light, even if the main power is on.
Downloaded from ManualsPrinter.com Manuals
11
Connecting the Machine
❖ When using in ad hoc mode / 802.11 ad hoc mode
1
ZGDH600J
1. If it is connected properly to the network, the LED is green when in ad hoc
mode or 802.11 ad hoc mode. If the LED is blinking, the machine is searching
for devices. The LED will light after a few seconds.
2. If the IEEE 802.11b interface unit is functioning, the LED lights up in orange.
Print the configuration page to verify settings.
Note
❒ For more information about printing a configuration page, see "Print List".
Reference
p.168 “Printing the Configuration Page”
Checking the Signal
This section describes how to check the machine's radio wave status.
When using in infrastructure mode, you can check the machine's radio wave status using the control panel.
A Press [System Settings].
B Press [Interface Settings].
C Press [IEEE 802.11b].
D Press [Wireless LAN Signal].
The machine's radio wave status appears.
E After checking radio wave status, press [Exit].
F Press the {User Tools/Counter} key to return to the User Tools / Counter / Inquiry menu.
Reference
p.30 “Using Utilities to Make Network Settings”
p.53 “IEEE 802.11b”
12
Downloaded from ManualsPrinter.com Manuals
Network Settings
Network Settings
This section describes the network settings you can change with User Tools (System Settings). Make settings according to functions you want to use and the interface to be connected.
1
Important
❒ These settings should be made by the system administrator, or with the advice of the system administrator.
Settings Required to Use the Printer/LAN-Fax
This section lists the settings required for using the printer or LAN-Fax function.
Ethernet
This section lists the settings required for using the printer or LAN-Fax function
with an Ethernet connection.
For details about how to specify the settings, see "Interface Settings".
Menu
User Tool
Setting Requirements
Interface Settings/Network
IP Address
Interface Settings/Network
Gateway Address
As required
Interface Settings/Network
DNS Configuration
As required
Interface Settings/Network
DDNS Configuration
As required
Interface Settings/Network
Domain Name
As required
Interface Settings/Network
WINS Configuration
As required
Interface Settings/Network
NW Frame Type
As required
Interface Settings/Network
LAN Type
Interface Settings/Network
Ethernet Speed
Interface Settings/Network
Effective Protocol
Interface Settings/Network
NCP Delivery Protocol
As required
Interface Settings/Network
SMB Computer Name
As required
Interface Settings/Network
SMB Work Group
As required
Interface Settings/Network
Permit SNMPv3 Communication
As required
Interface Settings/Network
Permit SSL/TLS Communication
As required
Interface Settings/Network
Host Name
As required
Interface Settings/Network
Machine Name
As required
Downloaded from ManualsPrinter.com Manuals
Necessary
Necessary
As required
Necessary
13
Connecting the Machine
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Effective].
1
❒ [LAN Type] is displayed when the wireless LAN board is installed. If Ethernet
and IEEE 802.11b (wireless LAN) are both connected, the selected interface
has priority.
Reference
p.49 “Interface Settings”
IEEE 802.11b (wireless LAN)
This section lists the settings required for using the printer or LAN-Fax function
with an IEEE 802.11b (wireless LAN) connection.
For details about how to specify the settings, see "Interface Settings".
Menu
User Tool
Setting Requirements
Interface Settings/Network
IP Address
Interface Settings/Network
Gateway Address
As required
Interface Settings/Network
DNS Configuration
As required
Interface Settings/Network
DDNS Configuration
As required
Interface Settings/Network
Domain Name
As required
Interface Settings/Network
WINS Configuration
As required
Interface Settings/Network
NW Frame Type
As required
Interface Settings/Network
LAN Type
Interface Settings/Network
Ethernet Speed
Interface Settings/Network
Effective Protocol
Interface Settings/Network
NCP Delivery Protocol
As required
Interface Settings/Network
SMB Computer Name
As required
Interface Settings/Network
SMB Work Group
As required
Interface Settings/Network
Permit SNMPv3 Communication
As required
Interface Settings/Network
Permit SSL/TLS Communication
As required
Interface Settings/Network
Host Name
As required
Interface Settings/Network
Machine Name
As required
Interface Settings/
IEEE 802.11b
Communication Mode
Interface Settings/
IEEE 802.11b
SSID Setting
As required
Interface Settings/
IEEE 802.11b
Channel
As required
Interface Settings/
IEEE 802.11b
WEP (Encryption) Setting
As required
14
Downloaded from ManualsPrinter.com Manuals
Necessary
Necessary
As required
Necessary
Necessary
Network Settings
Menu
Interface Settings/
IEEE 802.11b
User Tool
Setting Requirements
Transmission Speed
As required
1
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Effective].
❒ [IEEE 802.11b] and [LAN Type] are displayed when the wireless LAN interface
board is installed. If both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected interface takes precedence.
Reference
p.49 “Interface Settings”
Settings Required to Use Internet Fax
This section lists the settings required for using Internet Fax.
Ethernet
This section lists the settings required for using Internet Fax with an Ethernet
connection.
For details about how to specify the settings, see "Interface Settings" and "File
Transfer".
Menu
User Tool
Setting Requirements
Interface Settings/Network
IP Address
Necessary
Interface Settings/Network
Gateway Address
Necessary
Interface Settings/Network
DNS Configuration
As required
Interface Settings/Network
DDNS Configuration
As required
Interface Settings/Network
Domain Name
As required
Interface Settings/Network
WINS Configuration
As required
Interface Settings/Network
LAN Type
Interface Settings/Network
Ethernet Speed
Interface Settings/Network
Effective Protocol
Interface Settings/Network
NCP Delivery Protocol
As required
Interface Settings/Network
Permit SNMPv3 Communication
As required
Interface Settings/Network
Permit SSL/TLS Communication
As required
Interface Settings/Network
Host Name
As required
File Transfer
SMTP Server
File Transfer
SMTP Authentication
As required
File Transfer
POP before SMTP
As required
Downloaded from ManualsPrinter.com Manuals
Necessary
As required
Necessary
Necessary
15
Connecting the Machine
Menu
1
User Tool
Setting Requirements
File Transfer
Reception Protocol
Necessary
File Transfer
POP3 / IMAP4 Settings
As required
File Transfer
Administrator's E-mail Address
As required
File Transfer
E-mail Communication Port
File Transfer
E-mail Reception Interval
As required
File Transfer
Max. Reception E-mail Size
As required
File Transfer
E-mail Storage in Server
As required
File Transfer
Program / Change / Delete E-mail
Message
As required
File Transfer
Program / Change / Delete Subject
As required
File Transfer
Fax E-mail Account
Necessary
Necessary
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Effective].
❒ [LAN Type] is displayed when the wireless LAN interface board is installed. If
both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected interface takes precedence.
❒ SMTP Server and Fax E-mail Account must be specified in order to send Internet Fax.
❒ When POP before SMTP is set to [On], you must also make settings for Reception Protocol and POP3 / IMAP4 Settings.
❒ When SMTP Authentication is set to [On], you must also make settings for
Administrator's E-mail Address.
❒ E-mail Communication Port and Fax E-mail Account must be specified in order to receive Internet Fax.
❒ When setting POP before SMTP to [On], check POP3 port number in E-mail
Communication Port.
Reference
p.49 “Interface Settings”
p.55 “File Transfer”
16
Downloaded from ManualsPrinter.com Manuals
Network Settings
IEEE 802.11b (wireless LAN)
This section lists the settings required for using Internet Fax with an IEEE
802.11b (wireless LAN) connection.
For details about how to specify the settings, see "Interface Settings" and "File
Transfer".
Menu
User Tool
Setting Requirements
Interface Settings/Network
IP Address
Necessary
Interface Settings/Network
Gateway Address
Necessary
Interface Settings/Network
DNS Configuration
As required
Interface Settings/Network
DDNS Configuration
As required
Interface Settings/Network
Domain Name
As required
Interface Settings/Network
WINS Configuration
As required
Interface Settings/Network
Effective Protocol
Interface Settings/Network
NCP Delivery Protocol
Interface Settings/Network
LAN Type
Interface Settings/Network
Permit SNMPv3 Communication
As required
Interface Settings/Network
Permit SSL/TLS Communication
As required
Interface Settings/Network
Host Name
As required
Interface Settings/
IEEE 802.11b
Communication Mode
Interface Settings/
IEEE 802.11b
SSID Setting
As required
Interface Settings/
IEEE 802.11b
Channel
As required
Interface Settings/
IEEE 802.11b
WEP (Encryption) Setting
As required
Interface Settings/
IEEE 802.11b
Transmission Speed
As required
File Transfer
SMTP Server
File Transfer
SMTP Authentication
As required
File Transfer
POP before SMTP
As required
File Transfer
Reception Protocol
Necessary
File Transfer
POP3 / IMAP4 Settings
As required
File Transfer
Administrator's E-mail Address
As required
File Transfer
E-mail Communication Port
File Transfer
E-mail Reception Interval
As required
File Transfer
Max. Reception E-mail Size
As required
File Transfer
E-mail Storage in Server
As required
Downloaded from ManualsPrinter.com Manuals
1
Necessary
As required
Necessary
Necessary
Necessary
Necessary
17
Connecting the Machine
Menu
1
User Tool
Setting Requirements
File Transfer
Program / Change / Delete E-mail
Message
As required
File Transfer
Program / Change / Delete Subject
As required
File Transfer
Fax E-mail Account
Necessary
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Effective].
❒ [IEEE 802.11b] and [LAN Type] are displayed when the wireless LAN interface
board is installed. If both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected interface takes precedence.
❒ SMTP Server and Fax E-mail Account must be specified in order to send Internet Fax.
❒ When POP before SMTP is set to [On], you must also make settings for Reception Protocol and POP3 / IMAP4 Settings.
❒ When SMTP Authentication is set to [On], you must also make settings forAdministrator's E-mail Address.
❒ E-mail Communication Port and Fax E-mail Account must be specified in order to receive Internet Fax.
❒ When setting POP before SMTP to [On], check POP3 port number in E-mail
Communication Port.
Reference
p.49 “Interface Settings”
p.55 “File Transfer”
18
Downloaded from ManualsPrinter.com Manuals
Network Settings
Settings Required to Use E-mail Function
This section lists the settings required for sending e-mail.
1
Ethernet
This section lists the settings required for sending e-mail with an Ethernet connection.
For details about how to specify the settings, see "Interface Settings" and "File
Transfer".
Menu
User Tool
Setting Requirements
Interface Settings/Network
IP Address
Necessary
Interface Settings/Network
Gateway Address
Necessary
Interface Settings/Network
DNS Configuration
As required
Interface Settings/Network
DDNS Configuration
As required
Interface Settings/Network
Domain Name
As required
Interface Settings/Network
WINS Configuration
As required
Interface Settings/Network
Effective Protocol
Interface Settings/Network
Ethernet Speed
Interface Settings/Network
LAN Type
Interface Settings/Network
NCP Delivery Protocol
As required
Interface Settings/Network
Permit SNMPv3 Communication
As required
Interface Settings/Network
Host Name
As required
File Transfer
SMTP Server
File Transfer
SMTP Authentication
As required
File Transfer
POP before SMTP
As required
File Transfer
Reception Protocol
As required
File Transfer
POP3 / IMAP4 Settings
As required
File Transfer
Administrator's E-mail Address
As required
File Transfer
E-mail Communication Port
As required
File Transfer
Program / Change / Delete E-mail
Message
As required
File Transfer
Program / Change / Delete Subject
As required
File Transfer
Scanner Recall Interval Time
As required
File Transfer
Number of Scanner Recalls
As required
Downloaded from ManualsPrinter.com Manuals
Necessary
As required
Necessary
Necessary
19
Connecting the Machine
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Effective].
1
❒ [LAN Type] is displayed when the wireless LAN interface board is installed. If
both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected interface takes precedence.
❒ When POP before SMTP is set to [On], you must also make settings for Reception Protocol and POP3 / IMAP4 Settings.
❒ When setting POP before SMTP to [On], check POP3 port number in E-mail
Communication Port.
Reference
p.49 “Interface Settings”
p.55 “File Transfer”
IEEE 802.11b (wireless LAN)
This section lists the settings required for sending e-mail with an IEEE 802.11b
(wireless LAN) connection.
For details about how to specify the settings, see "Interface Settings" and "File
Transfer".
Menu
User Tool
Setting Requirements
Interface Settings/Network
IP Address
Necessary
Interface Settings/Network
Gateway Address
Necessary
Interface Settings/Network
DNS Configuration
As required
Interface Settings/Network
DDNS Configuration
As required
Interface Settings/Network
Domain Name
As required
Interface Settings/Network
WINS Configuration
As required
Interface Settings/Network
Effective Protocol
Necessary
Interface Settings/Network
LAN Type
Necessary
Interface Settings/Network
NCP Delivery Protocol
As required
Interface Settings/Network
Permit SNMPv3 Communication
As required
Interface Settings/Network
Permit SSL/TLS Communication
As required
Interface Settings/Network
Host Name
As required
Interface Settings/
IEEE 802.11b
Communication Mode
Interface Settings/
IEEE 802.11b
SSID Setting
As required
Interface Settings/
IEEE 802.11b
Channel
As required
20
Downloaded from ManualsPrinter.com Manuals
Necessary
Network Settings
Menu
User Tool
Setting Requirements
Interface Settings/
IEEE 802.11b
WEP (Encryption) Setting
As required
Interface Settings/
IEEE 802.11b
Transmission Speed
As required
File Transfer
SMTP Server
File Transfer
SMTP Authentication
As required
File Transfer
POP before SMTP
As required
File Transfer
Reception Protocol
As required
File Transfer
POP3 / IMAP4 Settings
As required
File Transfer
Administrator's E-mail Address
As required
File Transfer
E-mail Communication Port
As required
File Transfer
Program / Change / Delete E-mail
Message
As required
File Transfer
Program / Change / Delete Subject
As required
File Transfer
Scanner Recall Interval Time
As required
File Transfer
Number of Scanner Recalls
As required
1
Necessary
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Effective].
❒ [LAN Type] is displayed when the wireless LAN interface board is installed. If
both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected interface takes precedence.
❒ When POP before SMTP is set to [On], you must also make settings for Reception Protocol and POP3 / IMAP4 Settings.
❒ When setting POP before SMTP to [On], check POP3 port number in E-mail
Communication Port.
Reference
p.49 “Interface Settings”
p.55 “File Transfer”
Downloaded from ManualsPrinter.com Manuals
21
Connecting the Machine
Settings Required to Use Scan to Folder Function
This section lists the settings required for sending files.
1
Ethernet
This section lists the settings required for sending files with an Ethernet connection.
For details about how to specify the settings, see "Interface Settings" and "File
Transfer".
Menu
User Tool
Setting Requirements
Interface Settings/Network
IP Address
Necessary
Interface Settings/Network
Gateway Address
Necessary
Interface Settings/Network
DNS Configuration
As required
Interface Settings/Network
DDNS Configuration
As required
Interface Settings/Network
Domain Name
As required
Interface Settings/Network
WINS Configuration
As required
Interface Settings/Network
Effective Protocol
Interface Settings/Network
Ethernet Speed
Interface Settings/Network
LAN Type
Interface Settings/Network
NCP Delivery Protocol
As required
Interface Settings/Network
Permit SNMPv3 Communication
As required
Interface Settings/Network
Permit SSL/TLS Communication
As required
Interface Settings/Network
Host Name
As required
File Transfer
Default User Name / Password
(Send)
As required
File Transfer
Scanner Recall Interval Time
As required
File Transfer
Number of Scanner Recalls
As required
Necessary
As required
Necessary
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Effective].
❒ [LAN Type] is displayed when the wireless LAN interface board is installed. If
both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected interface takes precedence.
Reference
p.49 “Interface Settings”
p.55 “File Transfer”
22
Downloaded from ManualsPrinter.com Manuals
Network Settings
IEEE 802.11b (wireless LAN)
This section lists the settings required for sending files with an IEEE 802.11b
(wireless LAN) connection.
For details about how to specify the settings, see "Interface Settings" and "File
Transfer".
Menu
User Tool
1
Setting Requirements
Interface Settings/Network
IP Address
Necessary
Interface Settings/Network
Gateway Address
Necessary
Interface Settings/Network
DNS Configuration
As required
Interface Settings/Network
DDNS Configuration
As required
Interface Settings/Network
Domain Name
As required
Interface Settings/Network
WINS Configuration
As required
Interface Settings/Network
Effective Protocol
Necessary
Interface Settings/Network
LAN Type
Necessary
Interface Settings/Network
NCP Delivery Protocol
As required
Interface Settings/Network
Permit SNMPv3 Communication
As required
Interface Settings/Network
Permit SSL/TLS Communication
As required
Interface Settings/Network
Host Name
As required
Interface Settings/
IEEE 802.11b
Communication Mode
Interface Settings/
IEEE 802.11b
SSID Setting
As required
Interface Settings/
IEEE 802.11b
Channel
As required
Interface Settings/
IEEE 802.11b
WEP (Encryption) Setting
As required
Interface Settings/
IEEE 802.11b
Transmission Speed
As required
File Transfer
Default User Name / Password
(Send)
As required
File Transfer
Scanner Recall Interval Time
As required
File Transfer
Number of Scanner Recalls
As required
Necessary
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Effective].
❒ [IEEE 802.11b] and [LAN Type] are displayed when the wireless LAN interface
board is installed. If both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected interface takes precedence.
Downloaded from ManualsPrinter.com Manuals
23
Connecting the Machine
Reference
p.49 “Interface Settings”
p.55 “File Transfer”
1
Settings Required to Use the Network Delivery Scanner
This section lists the settings required for delivering data to network.
Ethernet
This section lists the settings required for delivering data to network with an
Ethernet connection.
For details about how to specify the settings, see "Interface Settings" and "File
Transfer".
Menu
User Tool
Setting Requirements
Interface Settings/Network
IP Address
Necessary
Interface Settings/Network
Gateway Address
As required
Interface Settings/Network
DNS Configuration
As required
Interface Settings/Network
DDNS Configuration
As required
Interface Settings/Network
Domain Name
As required
Interface Settings/Network
WINS Configuration
As required
Interface Settings/Network
Effective Protocol
Interface Settings/Network
Ethernet Speed
Interface Settings/Network
LAN Type
Interface Settings/Network
NCP Delivery Protocol
As required
Interface Settings/Network
Permit SNMPv3 Communication
As required
Interface Settings/Network
Permit SSL/TLS Communication
As required
Interface Settings/Network
Host Name
As required
File Transfer
Delivery Option
As required
File Transfer
Fax RX File Transmission
As required
File Transfer
Scanner Recall Interval Time
As required
File Transfer
Number of Scanner Recalls
As required
Necessary
As required
Necessary
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Effective].
❒ [LAN Type] is displayed when the wireless LAN interface board is installed.
When both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected interface takes precedence.
❒ If Delivery Option is set to [On], check that IP Address is specified.
24
Downloaded from ManualsPrinter.com Manuals
Network Settings
Reference
p.49 “Interface Settings”
p.55 “File Transfer”
1
IEEE 802.11b (wireless LAN)
This section lists the settings required for delivering data to network with an
IEEE 802.11b (wireless LAN) connection.
For details about how to specify the settings, see "Interface Settings" and "File
Transfer".
Menu
User Tool
Setting Requirements
Interface Settings/Network
IP Address
Interface Settings/Network
Gateway Address
As required
Interface Settings/Network
DNS Configuration
As required
Interface Settings/Network
DDNS Configuration
As required
Interface Settings/Network
Domain Name
As required
Interface Settings/Network
WINS Configuration
As required
Interface Settings/Network
Effective Protocol
Necessary
Interface Settings/Network
LAN Type
Necessary
Interface Settings/Network
NCP Delivery Protocol
As required
Interface Settings/Network
Permit SNMPv3 Communication
As required
Interface Settings/Network
Permit SSL/TLS Communication
As required
Interface Settings/Network
Host Name
As required
Interface Settings/
IEEE 802.11b
Communication Mode
Interface Settings/
IEEE 802.11b
SSID Setting
As required
Interface Settings/
IEEE 802.11b
Channel
As required
Interface Settings/
IEEE 802.11b
WEP (Encryption) Setting
As required
Interface Settings/
IEEE 802.11b
Transmission Speed
As required
File Transfer
Delivery Option
As required
File Transfer
Fax RX File Transmission
As required
File Transfer
Scanner Recall Interval Time
As required
File Transfer
Number of Scanner Recalls
As required
Downloaded from ManualsPrinter.com Manuals
Necessary
Necessary
25
Connecting the Machine
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Effective].
1
❒ [IEEE 802.11b] and [LAN Type] are displayed when the wireless LAN interface
board is installed. When both Ethernet and wireless LAN (IEEE 802.11b) are
connected, the selected interface takes precedence.
❒ If Delivery Option is set to [On], check that IP Address is specified.
Reference
p.49 “Interface Settings”
p.55 “File Transfer”
Settings Required to Use Network TWAIN Scanner
This section lists the settings required for using TWAIN Scanner under the network environment.
Ethernet
This section lists the settings required for using network TWAIN Scanner with
an Ethernet connection.
For details about how to specify the settings, see "Interface Settings".
Menu
User Tool
Setting Requirements
Interface Settings/Network
IP Address
Interface Settings/Network
Gateway Address
As required
Interface Settings/Network
DNS Configuration
As required
Interface Settings/Network
DDNS Configuration
As required
Interface Settings/Network
Domain Name
As required
Interface Settings/Network
WINS Configuration
As required
Interface Settings/Network
Effective Protocol
Necessary
Interface Settings/Network
LAN Type
Necessary
Interface Settings/Network
Ethernet Speed
As required
Interface Settings/Network
NCP Delivery Protocol
As required
Interface Settings/Network
Permit SNMPv3 Communication
As required
Interface Settings/Network
Permit SSL/TLS Communication
As required
Interface Settings/Network
Host Name
As required
26
Downloaded from ManualsPrinter.com Manuals
Necessary
Network Settings
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Effective].
❒ [LAN Type] is displayed when the wireless LAN interface board is installed.
When both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected interface takes precedence.
1
Reference
p.49 “Interface Settings”
IEEE 802.11b (wireless LAN)
This section lists the settings required for using network TWAIN Scanner with
an IEEE 802.11b (wireless LAN) connection.
For details about how to specify the settings, see "Interface Settings".
Menu
User Tool
Setting Requirements
Interface Settings/Network
IP Address
Interface Settings/Network
Gateway Address
As required
Interface Settings/Network
DNS Configuration
As required
Interface Settings/Network
DDNS Configuration
As required
Interface Settings/Network
Domain Name
As required
Interface Settings/Network
WINS Configuration
As required
Interface Settings/Network
Effective Protocol
Necessary
Interface Settings/Network
LAN Type
Necessary
Interface Settings/Network
NCP Delivery Protocol
As required
Interface Settings/Network
Permit SNMPv3 Communication
As required
Interface Settings/Network
Permit SSL/TLS Communication
As required
Interface Settings/Network
Host Name
As required
Interface Settings/
IEEE 802.11b
Communication Mode
Interface Settings/
IEEE 802.11b
SSID Setting
As required
Interface Settings/
IEEE 802.11b
Channel
As required
Interface Settings/
IEEE 802.11b
WEP (Encryption) Setting
As required
Interface Settings/
IEEE 802.11b
Transmission Speed
As required
Downloaded from ManualsPrinter.com Manuals
Necessary
Necessary
27
Connecting the Machine
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Effective].
1
❒ [IEEE 802.11b] and [LAN Type] are displayed when the wireless LAN interface
board is installed. When both Ethernet and wireless LAN (IEEE 802.11b) are
connected, the selected interface takes precedence.
Reference
p.49 “Interface Settings”
Settings Required to Use Document Server
This section lists the settings required for using Document Server function under
the network environment.
Ethernet
This section lists the settings required for using Document Server function with
the Ethernet connection.
For details about how to specify the settings, see "Interface Settings".
Menu
User Tool
Setting Requirements
Interface Settings/Network
IP Address
Necessary
Interface Settings/Network
Gateway Address
As required
Interface Settings/Network
DNS Configuration
As required
Interface Settings/Network
DDNS Configuration
As required
Interface Settings/Network
Domain Name
As required
Interface Settings/Network
WINS Configuration
As required
Interface Settings/Network
Effective Protocol
Interface Settings/Network
Ethernet Speed
Interface Settings/Network
LAN Type
Interface Settings/Network
NCP Delivery Protocol
As required
Interface Settings/Network
Permit SNMPv3 Communication
As required
Interface Settings/Network
Permit SSL/TLS Communication
As required
Interface Settings/Network
Host Name
As required
Necessary
As required
Necessary
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Effective].
❒ [LAN Type] is displayed when the wireless LAN interface board is installed.
When both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected interface takes precedence.
28
Downloaded from ManualsPrinter.com Manuals
Network Settings
Reference
p.49 “Interface Settings”
IEEE 802.11b (wireless LAN)
1
This section lists the settings required for using Document Server function with
an IEEE 802.11b (wireless LAN) connection.
For details about how to specify the settings, see "Interface Settings".
Menu
User Tool
Setting Requirements
Interface Settings/Network
IP Address
Necessary
Interface Settings/Network
Gateway Address
As required
Interface Settings/Network
DNS Configuration
As required
Interface Settings/Network
DDNS Configuration
As required
Interface Settings/Network
Domain Name
As required
Interface Settings/Network
WINS Configuration
As required
Interface Settings/Network
Effective Protocol
Necessary
Interface Settings/Network
LAN Type
Necessary
Interface Settings/Network
NCP Delivery Protocol
As required
Interface Settings/Network
Permit SNMPv3 Communication
As required
Interface Settings/Network
Permit SSL/TLS Communication
As required
Interface Settings/Network
Host Name
As required
Interface Settings/
IEEE 802.11b
Communication Mode
Interface Settings/
IEEE 802.11b
SSID Setting
As required
Interface Settings/
IEEE 802.11b
Channel
As required
Interface Settings/
IEEE 802.11b
WEP (Encryption) Setting
As required
Interface Settings/
IEEE 802.11b
Transmission Speed
As required
Necessary
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Effective].
❒ [IEEE 802.11b] and [LAN Type] are displayed when the wireless LAN interface
board is installed. When both Ethernet and wireless LAN (IEEE 802.11b) are
connected, the selected interface takes precedence.
Reference
p.49 “Interface Settings”
Downloaded from ManualsPrinter.com Manuals
29
Connecting the Machine
Using Utilities to Make Network Settings
1
This section describes how to make network settings using utilities.
You can also specify network settings using utilities such as Web Image Monitor,
SmartDeviceMonitor for Admin, and telnet.
Note
❒ For details about using Web Image Monitor, see "Using Web Image Monitor",
Network Guide.
❒ For details about using SmartDeviceMonitor for Admin, see "Using SmartDeviceMonitor for Admin", Network Guide.
❒ For Details about using telnet, see "Remote Maintenance", Network Guide.
Reference
"Using Web Image Monitor", Network Guide
"Using SmartDeviceMonitor for Admin", Network Guide
"Remote Maintenance by telnet", Network Guide
Interface Settings
This section describes how to make Interface settings using utilities.
Change settings by using Web Image Monitor, SmartDeviceMonitor for Admin,
and telnet.
❖ [Network] → [IP Address] → [Auto-Obtain (DHCP)]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Can be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [IP Address] → [Specify] → [IP Address]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Can be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [IP Address] → [Specify] → [Sub-net Mask]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Can be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [Gateway Address]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Can be used for specifying the setting.
• telnet: Can be used for specifying the setting.
30
Downloaded from ManualsPrinter.com Manuals
Network Settings
❖ [Network] → [DNS Configuration] → [Auto-Obtain (DHCP)]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
1
❖ [Network] → [DNS Configuration] → [Specify] → "DNS Server 1-3"
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [DDNS Configuration]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [Domain Name] → [Auto-Obtain (DHCP)]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [Domain Name] → [Specify] → [Domain Name]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [WINS Configuration] → [On] → "Primary WINS Server"
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [WINS Configuration] → [On] → "Secondary WINS Server"
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [WINS Configuration] → [On] → "Scope ID"
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
Downloaded from ManualsPrinter.com Manuals
31
Connecting the Machine
1
❖ [Network] → [WINS Configuration] → [Off]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [Effective Protocol] → "TCP / IP"
• Web Image Monitor: Cannot be used for specifying the setting.
• SmartDeviceMonitor for Admin: You can specify the TCP/IP settings if
SmartDeviceMonitor for Admin is communicating with the machine using
IPX/SPX.
• telnet: Can be used for specifying the setting.
❖ [Network] → [Effective Protocol] → "NetWare"
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: You can specify the IPX/SPX settings if
SmartDeviceMonitor for Admin is communicating with the machine using
TCP/IP.
• telnet: Can be used for specifying the setting.
❖ [Network] → [Effective Protocol] → "SMB"
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Can be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [Effective Protocol] → "AppleTalk"
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Can be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [NCP Delivery Protocol]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Can be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [Network] → [NW Frame Type] → [Auto Select]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [NW Frame Type] → [Ethernet II]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
32
Downloaded from ManualsPrinter.com Manuals
Network Settings
❖ [Network] → [NW Frame Type] → [Ethernet 802.2]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
1
❖ [Network] → [NW Frame Type] → [Ethernet 802.3]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [NW Frame Type] → [Ethernet SNAP]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [SMB Computer Name]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [SMB Work Group]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [Ethernet Speed]
• Web Image Monitor: Cannot be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [Network] → [LAN Type] → [Ethernet]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [LAN Type] → [IEEE 802.11b]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
Downloaded from ManualsPrinter.com Manuals
33
Connecting the Machine
1
❖ [Network] → [Ping Command]
• Web Image Monitor: Cannot be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [Network] → [Permit SNMP V3 Communication] → [Encryption Only]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [Permit SNMP V3 Communication] → [Encryption / Clear Text]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [Permit SSL / TLS Communication] → [Ciphertext Only]
• Web Image Monitor: Cannot be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [Network] → [Permit SSL / TLS Communication] → [Ciphertext Priority]
• Web Image Monitor: Cannot be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [Network] → [Permit SSL / TLS Communication] → [Ciphertext / Clear Text]
• Web Image Monitor: Cannot be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [Network] → [Host Name]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Can be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [Network] → [Machine Name]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
34
Downloaded from ManualsPrinter.com Manuals
Network Settings
❖ [IEEE 802.11b] → [Communication Mode]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
1
❖ [IEEE 802.11b] → [SSID Setting]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [IEEE 802.11b] → [Channel]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [IEEE 802.11b] → [WEP (Encryption) Setting]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [IEEE 802.11b] → [Transmission Speed]
• Web Image Monitor: Cannot be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Can be used for specifying the setting.
❖ [File Transfer] → [SMTP Server]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [File Transfer] → [SMTP Authentication]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [File Transfer] → [POP before SMTP]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
Downloaded from ManualsPrinter.com Manuals
35
Connecting the Machine
1
❖ [File Transfer] → [Reception Protocol]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [File Transfer] → [POP3 / IMAP4 Settings]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [File Transfer] → [Administrator's E-mail Address]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [File Transfer] → [E-mail Communication Port]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [File Transfer] → [E-mail Reception Interval]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [File Transfer] → [Max. Reception E-mail Size]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [File Transfer] → [E-mail Storage in Server]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [File Transfer] → [Default User Name / Password (Send)]
• Web Image Monitor: Can be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
36
Downloaded from ManualsPrinter.com Manuals
Network Settings
❖ [File Transfer] → [Fax E-mail Account]
• Web Image Monitor: Cannot be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
1
❖ [File Transfer] → [Scanner Recall Interval Time]
• Web Image Monitor: Cannot be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
❖ [File Transfer] → [Number of Scanner Recalls]
• Web Image Monitor: Cannot be used for specifying the setting.
• SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
• telnet: Cannot be used for specifying the setting.
Downloaded from ManualsPrinter.com Manuals
37
Connecting the Machine
Connecting the Machine to a Telephone
Line and Telephone
1
This section describes how to connect the machine to the telephone lines and select the line type.
Connecting the Telephone Line
This section describes how to connect the machine to the telephone lines.
To connect the machine to a telephone line, use a snap-in modular type connector.
Important
❒ Make sure the connector is the correct type before you start.
AJA009S
1. G3 (analog) line interface connector
2. External telephone connector
3. Extra G3 line interface connector
38
Downloaded from ManualsPrinter.com Manuals
Connecting the Machine to a Telephone Line and Telephone
Selecting the Line Type
This section describes how to select the line type.
Select the line type to which the machine is connected. There are two types: tone
and pulse dial.
Select the line type using Administrator Tools.
1
Note
❒ This function is not available in some regions.
Reference
p.112 “Select Dial / Push Phone”
Downloaded from ManualsPrinter.com Manuals
39
Connecting the Machine
1
40
Downloaded from ManualsPrinter.com Manuals
2. System Settings
This chapter describes user tools in the System Settings menu. For details on
how to access System Settings, see "Accessing User Tools".
General Features
This section describes the user tools in the General Features menu under System
Settings.
Default settings are shown in bold type.
❖ Panel Tone
The beeper (key tone) sounds when a key is pressed.
The default setting is On.
❖ Warm Up Notice (copier/Document Server)
You can have the beeper sound when the machine becomes ready to copy after leaving Energy Saver mode, or when the power is turned on.
The default setting is On.
❖ Copy Count Display (copier/Document Server)
The copy counter can be set to show the number of copies made (count up) or
the number of copies yet to be made (count down).
The default setting is Up (count up).
❖ Function Priority
Specify the mode to be displayed immediately after the operation switch is
turned on, or when System Reset mode is turned on.
The default setting is Copier.
❖ Print Priority
Print Priority is given to the mode selected.
When [Interleave] is selected, the current print job will be interrupted after a
maximum of five sheets.
The default setting is Display Mode.
When [Interleave] is selected, the current print job will be interrupted after a
maximum of five sheets.
When the optional Internal Tray 2 (1 bin tray), 1000–sheet finisher, 2 Tray finisher, or booklet finisher is installed on the machine, you can specify an output tray for each documents are delivered. For details about how to specify
an output tray for each function, see "Output: copier", "Output: Document
Server", "Output: Facsimile", "Output: Printer".
Downloaded from ManualsPrinter.com Manuals
41
System Settings
2
❖ Function Reset Timer
You can set the length of time the machine waits before changing modes
when using the multi-access function.
This is useful if you are making many copies and have to change settings for
each copy. If you set a longer reset period, you can prevent interruption from
other functions.
The Function Reset Timer setting is ignored if [Interleave] is set for Print Priority.
The default setting is Set Time.
When you select [Set Time], enter the time (3–30 seconds, in 1 second increments) using the number keys.
The default setting for Set Time is 3 seconds.
❖ Output: Copier (copier)
Specify a tray to which documents are delivered.
ATX001S
1. Finisher Upper Tray
2. Finisher Shift Tray
3. Finisher Shift Tray 1
4. Finisher Shift Tray 2
5. Internal Tray 1
6. Internal Tray 2
The default setting is Internal Tray 1.
❖ Output: Document Server (Document Server)
Specify a tray to which documents are delivered.
The default setting is Internal Tray 1.
❖ Output: Facsimile (facsimile)
Specify a tray to which documents are delivered.
The default setting is Internal Tray 1.
42
Downloaded from ManualsPrinter.com Manuals
General Features
❖ Output: Printer (printer)
Specify a tray to which documents are delivered.
The default setting is Internal Tray 1.
The output trays set on the printer driver have priority over the output tray
specified above.
❖ Prepare Stapling
When the booklet finisher is installed, perform a stapling test (five to seven
times) after replacing staples for saddle stitching, or removing jammed staples.
2
❖ <F/F4>Size Setting
Currently three types of F size are available; 81/2"×13"L, 81/4"×13"L and
8"×13"L. The ADF or exposure glass cover sensor cannot distinguish these
three types of originals. This function sets the F size from the ADF or exposure glass cover sensor. Auto Paper Select or Auto Reduce/Enlarge can be
used for F size originals based on this setting.
The default setting is 81/2"×13"L.
Reference
p.3 “Accessing User Tools”
"Function Compatibility", Copy/Document Server Reference
Output tray settings
You cannot interrupt the current stapling job even if a stapling job is specified
by a different function.
When the 1000-sheet finisher, 2 Tray finisher or booklet finisher is installed and
stapling or shift-sorting is specified for a job, the job will be delivered to the finisher shift tray, finisher shift tray 1 or finisher shift tray 2 regardless of the output
tray specified.
Downloaded from ManualsPrinter.com Manuals
43
System Settings
Tray Paper Settings
This section describes the user tools in the Tray Paper Settings menu under System Settings.
Default settings are shown in bold type.
2
Important
❒ If the specified paper size differs from the actual size of the paper loaded in
the paper tray, a misfeed might occur because the correct paper size was not
detected.
❖ Paper Tray Priority: Copier (copier/Document Server)
Specify the tray to supply paper for output.
The default setting is Tray 1.
❖ Paper Tray Priority: Facsimile (facsimile)
Specify the tray to supply paper for output.
The default setting is Tray 1.
❖ Paper Tray Priority: Printer (printer)
Specify the tray to supply paper for output.
The default setting is Tray 1.
❖ Tray Paper Size: Tray 1-4
Select the size of the paper loaded in the paper tray.
The paper sizes you can set for Tray 1 to Tray 4 are as follows:
• A3L, B4 JIS (Japanese Industrial Standard)L, A4K, A4L, B5 JISK,
B5 JISL, A5L
• 11"×17"L, 81/2"×14"L, 81/2"×13"L, 81/2"×11"K, 81/2"×11"L,
81/4"×13"L, 81/4"×14"L, 11"×14"L, 8"×13"L, 71/4"×101/2"L,
8"×101/2"K, 8"×101/2"L, 51/2"×81/2"L
The default setting for Tray 1 is A4K / 812" × 11"K.
The default setting for Tray 2 is A3L / 11" × 17"L.
The default setting for Tray 3 is A4L / 81/2" × 11"L.
The default setting for Tray 4 is A4L / 81/2" × 14"L.
You can specify a custom size of between 148.0 and 297.0 mm (5.8"-11.7") vertically, and between 210.0 and 432.0 mm (3.3"-17.0") horizontally.
The paper guide for the optional LCT (Large Capacity Tray) is fixed for A4K,
81/2"×11"K size paper. Contact your service representative if you need to
change the paper size.
If the paper size set for the selector in paper tray is different to the paper size
for this setting, the paper size of the dial has priority.
If you load paper of a size not indicated on the paper size selector in the paper
tray, set the dial to " ".
44
Downloaded from ManualsPrinter.com Manuals
Tray Paper Settings
❖ Paper Type: Bypass Tray
Sets the display so you can see what type of paper is loaded in the bypass tray.
• The paper types you can set for the bypass tray are as follows:
recycled paper, special paper, colour paper, letterhead, label paper, prepunched paper, bond paper, cardstock, thick paper, OHP
The default setting is No Display.
❖ Paper Type: Tray 1-4
Sets the display so you can see what type of paper is loaded in each paper
tray. The print function uses this information to automatically select the paper tray.
• The paper types you can set are as follows:
recycled paper, special paper, colour paper, letterhead, preprinted paper,
prepunched paper, bond paper, cardstock
The default setting for "Paper Type" is No Display.
The default setting for "Copying Method in Duplex" is 2 Sided Copy.
The default setting for "Apply Auto Paper Select" is Yes.
When paper of the same type and size is loaded in two different paper trays
and you want to specify tray for 2 Sided Copy and tray for 1 Sided Copy,
specify the upper tray for 2 Sided Copy. If one of the trays is specified as the
default in Paper Tray Priority, assign 2 Sided Copy to that tray.
A mark appears next to the paper tray if [No] is selected in "Apply Auto Paper Select".
[Auto Paper Select] can only be selected for the copier function if [No Display]
and [Recycled Paper] are selected. If [No] is selected, Auto Paper Select is not
valid for the tray.
2
❖ Paper Type: LCT
Sets the display so you can see what type of paper is loaded in the LCT.
The paper types you can set are as follows:
• recycled paper, special paper, colour paper, letterhead, preprinted paper,
prepunched paper, bond paper, cardstock
The default setting for "Paper Type" is No Display.
The default setting for "Copying Method in Duplex" is 2 Sided Copy.
The default setting for "Apply Auto Paper Select" is Yes.
A mark appears next to the LCT if [No] is selected in "Apply Auto Paper Select".
[Auto Paper Select] can only be selected for the copier function if [No Display]
and [Recycled Paper] are selected. If [No] is selected, Auto Paper Select is not
valid for the tray.
Downloaded from ManualsPrinter.com Manuals
45
System Settings
2
❖ Cover Sheet Tray
Allows you to specify and display the paper tray that is setting cover sheets.
After selecting the paper tray, you can also specify the display timing and
copy method for two-sided copying.
The default setting for "Tray to Program" is Off.
Functions using the cover sheet tray setting are the front cover function and
front/back cover function.
When [At Mode Selected] is selected, cover sheet tray settings only appear
when the cover function or slip sheet function is selected.
When [Full Time] is selected, the cover sheet tray is always displayed.
You can set Copying Method in Duplex only when [At Mode Selected] is selected.
❖ Slip Sheet Tray
Allows you to specify and display the paper tray that is inserting slip sheets.
After selecting the paper tray, you can also specify the display timing and
copy method for two-sided copying.
The default setting for "Tray to Program" is Off.
When [At Mode Selected] is selected, slip sheet tray settings only appear when
the cover function or slip sheet function is selected.
❖ Printer Bypass Paper Size
Specify the size of the paper in the bypass tray when printing data from the
computer.
• The paper types you can set for trays are as follows:
A3L, A4K, A4L, A5K, A5L, A6L, B4 JISL, B5 JISK, B5 JISL,
11" × 17"L, 81/2" × 14"L, 81/2" × 13"L, 81/2" × 11"K, 81/2" × 11"L,
81/4" × 13"L, 8" × 13"L, 71/4" × 101/2"K, 71/4" × 101/2"L, 51/2" × 81/2"L
The default setting is A4K.
You can specify a custom size of between 100.0 and 297.0 mm (3.9"-11.7") vertically, and between 148.0 and 600.0 mm (5.8"-23.6") horizontally.
Reference
p.3 “Accessing User Tools”
"Covers", Copy/ Document Server Reference
"Slip Sheets", Copy/ Document Server Reference
46
Downloaded from ManualsPrinter.com Manuals
Timer Settings
Timer Settings
This section describes the user tools in the Timer Settings menu under System
Settings.
Default settings are shown in bold type.
❖ Auto Off Timer
After a specified period has passed, following job completion, the machine
automatically turns off, in order to conserve energy. This function is called
"Auto Off". The machine status after the Auto Off operation is referred to as
"Off mode", or "Sleep mode". For the Auto Off Timer, specify the time to
elapse before "Auto Off".
The default setting is 1 minute(s).
Enter a time interval between 10 seconds and 240 minutes, using the number
keys
From "Off mode" or "Sleep mode", the machine is ready to use within 10 seconds.
Auto Off may not work when error messages appear.
The machine may not shift to "Sleep Mode" at the set time, if the main power
switch has just been turned on and functions other than copier function are
still in the process of starting up.
2
❖ Panel Off Timer
Set the amount of time the machine waits before switching the panel off after
copying has finished or the last operation is performed.
Enter a time interval between 10 seconds and 240 minutes, using the number
keys.
The default setting is 1 minute(s).
❖ System Auto Reset Timer
The System Reset setting automatically switches the screen to that of the function set in Function Priority when no operations are in progress, or when an
interrupted job is cleared. This setting determines the system reset interval.
The time can be set from 10 to 999 seconds, using the number keys
The default setting is On, 60 seconds.
❖ Copier / Document Server Auto Reset Timer (copier/Document Server)
Specifies the time to elapse before copier and Document Server modes reset.
If [Off] is selected, the machine does not automatically switch to the user code
entry screen.
The time can be set from 10 to 999 seconds, using the number keys.
The default setting is On, 60 seconds.
❖ Facsimile Auto Reset Timer (facsimile)
Specifies the time to elapse before the facsimile mode resets.
The time can be set from 30 to 999 seconds, using the number keys.
The default setting is 30 seconds.
Downloaded from ManualsPrinter.com Manuals
47
System Settings
❖ Printer Auto Reset Timer (printer)
Specifies the time to elapse before the printer function resets.
If [Off] is selected, the machine does not automatically switch to the user code
entry screen.
The time can be set from 10 to 999 seconds, using the number keys.
The default setting is On, 60 seconds.
2
❖ Scanner Auto Reset Timer (scanner)
Specifies the time to elapse before the scanner function resets.
If [Off] is selected, the machine will not automatically switch to the user code
entry screen.
The time can be set from 10 to 999 seconds, using the number keys.
The default setting time is On, 60 seconds.
❖ Set Date
Set the date for the copier's internal clock using the number keys.
To change between year, month, and day, press [ ← ] and [ → ].
❖ Set Time
Set the time for the copier's internal clock using the number keys.
Enter the time using the 24–hour format (in 1 second increments).
To change between hours, minutes and seconds, press [ ← ] and [ → ].
❖ Auto Logout Timer
Specify whether or not to automatically log out a user when the user does not
operate the machine for a specified period of time after logging in.
The time can be set from 10 to 999 seconds, in one second increments, using
the number keys.
The default setting time is On, 30 seconds.
Reference
p.3 “Accessing User Tools”
48
Downloaded from ManualsPrinter.com Manuals
Interface Settings
Interface Settings
This section describes the user tools in the Interface Settings menu under System
Settings.
Default settings are shown in bold type.
2
Network
This section describes the user tools in the Network menu under Interface Settings.
❖ IP Address
Before using this machine in the network environment, you must specify the
IP address and subnet mask.
When you select [Specify], enter the IP Address and subnet mask as "xxx.xxx.xxx.xxx"
("x" indicates a number).
The default setting is Auto-Obtain (DHCP).
When you select [Specify], make sure that the IP address is different from that
of other machines on the network.
The physical address (MAC address) also appears.
❖ Gateway Address
A gateway is a connection or interchange point between two networks.
Specify the gateway address for the router or host computer used as a gateway.
The default setting is 000.000.000.000.
❖ DNS Configuration
Make settings for the DNS server.
When you select [Specify], enter the DNS Server IP address as “xxx.xxx.xxx.xxx"(“x"
indicates a number).
The default setting is Auto-Obtain (DHCP).
❖ DDNS Configuration
Specify the DDNS settings.
The default setting is Active.
❖ Domain Name
Specify the domain name.
Enter the domain name using up to 63 characters.
❖ WINS Configuration
Specify the WINS server settings.
The default setting is On.
If [On] is selected, enter the WINS Server IP address as “xxx.xxx.xxx.xxx"(“x"
indicates a number).
If DHCP is in use, specify the scope ID.
Enter the scope ID using up to 31 characters.
Downloaded from ManualsPrinter.com Manuals
49
System Settings
❖ Effective Protocol
Select the protocol to use in the network.
The default setting for TCP/IP is Effective.
The default setting for NetWare is Effective.
The default setting for SMB is Effective.
The default setting for AppleTalk is Effective.
2
❖ NCP Delivery Protocol
Select the protocol for NCP delivery.
The default setting is TCP / IP Priority.
❖ NW Frame Type
Select the frame type when you use NetWare.
The default setting is Auto Select.
❖ SMB Computer Name
Specify the SMB computer name.
Enter the computer name using up to 15 characters.
"*+,/:;<>=?[\]|. and spaces cannot be entered.
Do not set a computer name starting with RNP and rnp.
Use uppercase letters for alphabets.
❖ SMB Work Group
Specify the SMB work group.
Enter the computer name using up to 15 characters.
"*+,/:;<>=?[\]|. and spaces cannot be entered.
Use uppercase letters for alphabet.
❖ Ethernet Speed
Set the access speed for networks.
The default setting is Auto Select.
Select a speed that matches your network environment. [Auto Select] should
usually be selected.
Machine
10Mbps Half
Duplex
10Mbps Full
Duplex
100Mbps
Half Duplex
100Mbps Full
Duplex
Auto Select
10Mbps Half
Duplex
b
-
-
-
b
10Mbps Full
Duplex
-
b
-
-
-
100Mbps
Half Duplex
-
-
b
-
b
100Mbps Full
Duplex
-
-
-
b
-
Auto Select
b
-
b
-
b
Router/HUB
50
Downloaded from ManualsPrinter.com Manuals
Interface Settings
❖ LAN Type
When you have installed the IEEE 802.11b interface unit, select the method of
connection.
The default setting is Ethernet.
[LAN Type] is displayed when wireless LAN board is installed. If Ethernet and
IEEE 802.11b (wireless LAN) are both connected, the selected interface has
priority.
2
❖ Ping Command
Check the network connection with ping command using given IP address.
If you fail to connect to the network, check the following, and then retry the
ping command.
• Make sure that “TCP/IP” in [Effective Protocol] is set to “Effective”.
• Check that the machine with assigned IP address is connected to the network.
• There is a possibility that the same IP address is used for the specified
equipment.
❖ Permit SNMP V3 Communication
Set the encrypted communication of SNMPv3.
The default setting is Encryption / Clear Text.
If you select to [Encryption Only], you need to set an encryption password for
the machine.
❖ Permit SSL / TLS Communication
Set the encrypted communication of SSL / TLS.
The default setting is Ciphertext Priority.
If you set to [Ciphertext Only], you need to install the SSL certificate for the machine.
❖ Host Name
Specify the host name.
Enter the host name using up to 63 characters.
❖ Machine Name
Specify the machine name.
Enter the machine name using up to 31 characters.
Downloaded from ManualsPrinter.com Manuals
51
System Settings
Parallel Interface
This section describes the user tools in the Parallel Interface menu under Interface Settings.
[Parallel Interface] is displayed when this machine is installed with the IEEE 1284
interface board.
2
❖ Parallel Timing
Specify the timing for the parallel interface. Normally, you do not need to
change this setting.
The default setting is ACK Outside.
❖ Parallel Communication Speed
Sets the communication speed for the parallel interface. If the speed is too
high, data may not be transferred smoothly. If this happens, change the setting to "Standard".
The default setting is High Speed.
❖ Selection Signal Status
Sets the level for the select signal of the parallel interface.
The default setting is High.
❖ Input Prime
Sets whether to validate or invalidate the input prime signal upon reception.
Normally you do not need to change this setting.
The default setting is Invalid.
❖ Bidirectional Communication
Sets the printer's response mode to a status acquisition request when using a
parallel interface. If you experience problems using another manufacturer's
machine, set this to "Off".
The default setting is On.
When set to [Off], the bidirectional communication function will be disabled,
and the printer driver will not be installed under Windows Auto Detect function.
❖ Signal Control
Specifies how error during printing or sending facsimile from the computer
is to be dealt with. Normally, you do not need to change this setting.
The default setting is Job Acceptance Priority.
52
Downloaded from ManualsPrinter.com Manuals
Interface Settings
IEEE 802.11b
This section describes the user tools in the IEEE 802.11b menu under Interface
Settings.
[IEEE 802.11b] is displayed when this machine is installed with the wireless LAN
interface board.
Be sure to make all settings simultaneously.
2
❖ Communication Mode
Specifies the communication mode of the wireless LAN.
The default setting is 802.11 Ad hoc.
❖ SSID Setting
Specifies SSID to distinguish the access point in infrastructure mode or 802.11
ad hoc mode.
The characters that can be used are ASCII 0x20-0x7e (32 bytes).
If blank is specified in 802.11b ad hoc mode or ad hoc mode, “ASSID" appears.
Default setting is blank (ASSID).
❖ Channel
Specifies a channel when you select 802.11b ad hoc mode or ad hoc mode.
The default setting is 11.
The following channels are available:
• Metric version: 1-14
• Inch version: 1-11
❖ WEP (Encryption) Setting
Specifies the encryption of the IEEE 802.11b (wireless LAN). If this is set to
[Active], you must enter the WEP key.
• WEP
The default setting is Inactive.
• Encryption
10 alphanumeric characters must be entered for 64 bit, 26 characters for 128 bit.
❖ Wireless LAN Signal
When using in infrastructure mode, you can check the machine's radio wave
status using the control panel.
Radio wave status is displayed when you press [Wireless LAN Signal].
❖ Transmission Speed
Specifies the communication speed of the IEEE 802.11b (wireless LAN).
The default setting is Auto.
❖ Return to Defaults
You can return the IEEE 802.11b (wireless LAN) settings to their defaults.
Reference
p.3 “Accessing User Tools”
Downloaded from ManualsPrinter.com Manuals
53
System Settings
Print List
This section describes how to print the configuration page.
You can check items related to the network environment.
The configuration page shows the current network settings and network information.
2
A Press [System Settings].
B Press [Interface Settings].
C Press [Print List].
D Press the {Start} key.
The configuration page is printed.
E Press [Exit].
F Press the {User Tools/Counter} key.
54
Downloaded from ManualsPrinter.com Manuals
File Transfer
File Transfer
This section describes the user tools in the File Transfer menu under System Settings.
Default settings are shown in bold type.
❖ Delivery Option
Enables or disables sending stored or scanned documents to the ScanRouter
delivery server.
The default setting is Off.
Specify this option when selecting whether or not to use the ScanRouter delivery software. If you do, you will have to preregister I/O devices in the
ScanRouter delivery software.
2
❖ Capture Server IP Address
Specify the capture server IP address.
This setting appears when the media link board is installed, and that the capture function is being used by the ScanRouter delivery software.
❖ Fax RX File Transmission
• Setting per Line
Specifies whether or not received fax documents are sent to the ScanRouter
delivery software for each fax line.
The default setting for Line 1 is Do not Deliver.
The default setting for Line 2 is Do not Deliver.
The default setting for Line 3 is Do not Deliver.
• Print at Deliver
Specifies whether or not received fax documents sent to ScanRouter delivery software should also be printed at the same time.
The default setting is Do not Print.
• File to Deliver
Specifies whether all received fax documents or only received fax documents that include delivery codes (documents with an ID and SUB/SEP
code) are sent to ScanRouter delivery software.
The default setting is All Files.
• Dlvry Failure File
• Print File
• Delete File
If a received fax document cannot be sent to ScanRouter delivery software,
it is stored in memory. To print a stored file, select [Print File] to delete, select [Delete File].
If the machine can send the data to ScanRouter delivery software, it does
so automatically.
If you delete the data, you will not be able to distribute or print it.
Downloaded from ManualsPrinter.com Manuals
55
System Settings
2
❖ SMTP Server
Specify the SMTP server name.
If DNS is in use, enter the host name.
If DNS is not in use, enter the SMTP server IP address.
The default setting for "Port No." is 25.
Enter the server name using up to 127 characters. Spaces cannot be entered.
Enter port number between 1 and 65535 using the number keys, and then
press the {q} key.
SMTP server shares the same port number with Direct SMTP server.
❖ SMTP Authentication
Specify SMTP authentication (PLAIN, LOGIN, CRAMMD5, DIGEST-MD5).
When sending e-mail to an SMTP server, you can enhance the SMTP server
security level using authentication that requires entering the user name and
password.
If the SMTP server requires authentication, set [SMTP Authentication] to [On],
and then specify the user name, e-mail address, password and encryption.
• Enter the user name using up to 191 characters.
Spaces cannot be entered. Depending on the SMTP server type, "realm"
must be specified. Add "@" after the user name, as in "user name@realm".
• Enter the password using up to 128 characters.
Spaces cannot be entered.
• Select Encryption as follows:
"Encryption"-[Auto]
Use If the authentication method is PLAIN, LOGIN, CRAM-MD5, or DIGEST-MD5.
"Encryption"-[On]
Use If the authentication method is CRAMMD5 or DIGEST-MD5.
"Encryption"-[Off]
Use If the authentication method is PLAIN, or LOGIN.
Enter the user name and password to be set for the Administrator's e-mail address when using Internet Fax.
The default setting is Off.
56
Downloaded from ManualsPrinter.com Manuals
File Transfer
❖ POP before SMTP
Specify POP authentication (POP before SMTP).
When sending e-mail to an SMTP server, you can enhance the SMTP server
security level by connecting to the POP server for authentication.
If you set POP before SMTP to [On], specify the waiting time after authentication, user name, e-mail address and password.
• Wait Time after Authent.: 300 msec
Specify "Wait Time after Authent." from zero to 10,000 milliseconds, in increments of one millisecond.
• User Name
Enter the user name using up to 191 characters. Spaces cannot be entered.
• E-mail Address
Enter the E-mail Address using up to 128 characters. Spaces cannot be entered.
• Password
Enter the password using up to 128 characters. Spaces cannot be entered.
The default setting is Off.
To enable POP server authentication before sending e-mail via the SMTP
server, set [POP before SMTP] to [On]. E-mail is sent to the SMTP server after the
time specified for "Wait Time after Authent." has elapsed.
If you select [On], enter server name in POP3 / IMAP4 Settings. Also, check
POP3 port number in E-mail Communication Port.
2
❖ Reception Protocol
Specify Reception Protocol for receiving Internet Fax.
The default setting is POP3.
❖ POP3 / IMAP4 Settings
Specify the POP3/IMAP4 server name for receiving Internet faxes.
The specified POP3/IMAP4 server name is used for [POP before SMTP].
• Server Name
If DNS is in use, enter the host name.
If DNS is not in use, enter the POP3/IMAP4 or server IP address.
Enter POP3/IMAP4 server name using up to 127 characters. Spaces cannot
be entered.
• Select Encryption as follows:
"Encryption"-[Auto]
Password encryption is automatically set according to the POP/IMAP
server settings.
"Encryption"-[On]
Encrypt password.
"Encryption"-[Off]
Do not encrypt password.
The default setting is Auto.
Downloaded from ManualsPrinter.com Manuals
57
System Settings
2
❖ Administrator's E-mail Address
Specify the Administrator's E-mail Address.
If a failure occurs in the machine or consumables need to be replaced, e-mail
messages are sent to the Administrator's E-mail Address by E-mail Notification function.
On e-mailed scanned documents, if the sender is not specified this appears as
the sender's address.
When sending e-mail under the Internet fax function, administrator's e-mail
address will appear as the sender’s address under the following conditions:
• The sender has not been specified and the machine’s e-mail address has
not been registered.
• The specified sender is not registered in the machine’s address book and
the machine’s e-mail address has not been registered.
When conducting SMTP authentication for the transmitted files under the Internet fax function, the Administrator's E-mail Address will appear in the
“From:" box. If you have specified the user name and e-mail address in [SMTP
Authentication], make sure to specify this setting.
Enter up to 128 characters.
On e-mailed scanned documents, if [Auto Specify Sender Name] is [Off], specify
the sender.
❖ E-mail Communication Port
Specify the port numbers for receiving Internet faxes. The specified POP3
port number is used for POP before SMTP.
The default setting for POP3 is 110.
The default setting for IMAP4 is 143.
The default setting for SMTP is 25.
Enter a port number between 1 and 65535 using the number keys, and then
press the {q} key.
❖ E-mail Reception Interval
Specify, in minutes, the time interval for receiving Internet faxes via POP3 or
IMAP4 server.
The default setting is On, 15 minute(s)
If [On] is selected, the time can be set from 2 to 1440 minutes in increments of
one minute.
❖ Max. Reception E-mail Size
Specify the maximum reception e-mail size for receiving Internet faxes.
The default setting is 2MB.
Enter a size from one to 50 MB in increments of one megabyte.
❖ E-mail Storage in Server
Specify whether or not to store received Internet fax e-mails on the POP3 or
IMAP4 server.
The default setting is Off.
58
Downloaded from ManualsPrinter.com Manuals
File Transfer
❖ Default User Name / Password (Send)
Specify the user name and password required when sending scan files directly to a shared folder on a computer running Windows, to an FTP server, or to
a NetWare server.
Enter in up to 64 characters.
❖ Program / Change / Delete E-mail Message
You can program, change, or delete the e-mail message used when sending
an Internet fax or scan file as an attachment.
Program / Change:
A Press [System Settings].
B Press [File Transfer].
C Press [TNext].
D Press [Program / Change / Delete E-mail Message].
E Press [*Not Programmed].
To change the registered e-mail message, select the e-mail message to
change.
F Press [Change] on the right side of "Name".
G Enter a name, and then press [OK].
Enter the name using up to 20 characters.
H Press [Edit] under "Edit Message".
I Enter the text, and then press [OK].
Enter up to five lines of text. Each line can consist of up to 80 characters.
To start a new line, press [OK] to return to the e-mail message screen, and
then press [T] in "Select Line to Edit:".
J Press [OK].
K Press [Exit].
2
Delete:
A Press [System Settings].
B Press [File Transfer].
C Press [TNext].
D Press [Program / Change / Delete E-mail Message].
E Press [Delete].
F Select the e-mail message to delete.
The confirmation message about deleting appears.
G Press [Yes].
H Press [Exit].
Downloaded from ManualsPrinter.com Manuals
59
System Settings
2
❖ Program / Change / Delete Subject
You can program, change, or delete the subject used when sending an Internet fax or scan file as an attachment.
Program / Change:
A Press [System Settings].
B Press [File Transfer].
C Press [TNext].
D Press [Program / Change / Delete Subject].
E Press [*Not Programmed].
To change the registered subject, select the subject to change.
F Enter the text, and then press [OK].
Enter the subject using up to 20 characters.
G Press [Exit].
Delete:
A Press [System Settings].
B Press [File Transfer].
C Press [TNext].
D Press [Program / Change / Delete Subject].
E Press [Delete].
F Select the subject to delete.
The confirmation message about deleting appears.
G Press [Yes].
H Press [Exit].
❖ Scanner Recall Interval Time
Specifies the interval the machine waits before resending a scan file, if it cannot be sent to the delivery server or mail server.
The default setting is 300 seconds.
The interval time can be set from 60 to 900 seconds in one second increments,
using the number keys.
This setting is for the scanner function.
❖ Number of Scanner Recalls
Sets a maximum number of times a scan file is resent to the delivery server or
mail server.
The default setting is On, 3 time(s).
If [On] is selected, the number of times can be set from 1 to 99. This setting is
for the scanner function.
This setting is for the scanner function.
60
Downloaded from ManualsPrinter.com Manuals
File Transfer
❖ Fax E-mail Account
Specify e-mail address, user name and password for receiving Internet faxes.
• E-mail Address
Enter an e-mail address using up to 128 characters.
• User Name
Enter a user name using up to 191 characters.
• Password
Enter a password using up to 128 characters.
2
❖ Auto Specify Sender Name
Set whether or not to specify the name of the sender when sending e-mail.
• On
If you select [On], the specified e-mail address will appear in the “From:"
box. If you do not specify the sender’s address, the administrator’s e-mail
address will appear in the “From:" box.
If you do not specify the sender when sending a file by e-mail under the
fax function, or if the specified e-mail address is not registered in the machine’s address book, the machine’s e-mail address will appear in the
“From:” box. If the machine does not have an e-mail address, the administrator’s e-mail address will appear in the “From:” box.
• Off
If you select [Off], the specified e-mail address will appear in the “From:"
box, but you cannot send e-mail without specifying the sender’s e-mail address. Under the fax function, you cannot send e-mail if the specified sender’s e-mail address is not registered in the machine’s address book.
The default setting is Off.
Reference
p.3 “Accessing User Tools”
Downloaded from ManualsPrinter.com Manuals
61
System Settings
Administrator Tools
2
This section describes the user tools in the Administrator Tools menu under System Settings.
Default settings are shown in bold type.
Administrator Tools are used by the administrator. To change these settings,
contact the administrator.
We recommend specifying Administrator Authentication before making Administrator Tools settings.
❖ User Authentication Management
• User Code Auth.
Using User Code Authentication, you can limit the available functions and
supervise their use.
When using User Code Authentication, register the user code.
Using the Printer PC Control function, you can obtain a log of prints corresponding to the codes entered using the printer driver.
For details about Basic Authentication, Windows Authentication, LDAP
Authentication, and Integration Server Authentication, consult your administrator.
• Copier
• Document Server
• Facsimile
• Scanner
• Printer
• Printer: PC Control
• Basic Auth.
• Windows Auth.
• LDAP Auth.
• Integration Svr. Auth.
• Off
The default setting is Off.
❖ Administrator Authentication Management
For details about this function, consult your administrator.
❖ Program / Change Administrator
For details about this function, consult your administrator.
❖ Key Counter Management
Specify the functions you want to manage with the key counter.
62
Downloaded from ManualsPrinter.com Manuals
Administrator Tools
❖ Extended Security
Specify whether or not to use the extended security functions. For details
about the extended security functions, consult your administrator.
❖ Display / Print Counter
Allows you to view and print the number of prints.
• Display / Print Counter
Displays the number of prints for each function (Total, Copier, Facsimile,
Printer, A3 / DLT, Duplex, Staple).
• Print Counter List
Prints out a list of the number of prints made under each function.
2
❖ Display / Clear / Print Counter per User
Allows you to view and print the numbers of prints accessed with user codes,
and to set those values to 0.
Press [UPrev.] and [TNext] to show all the numbers of prints.
The number of prints may differ from the counter values shown in Display /
Print Counter.
• Print Counter List for All Users
Prints the counter value for all the users.
• Clear Counter List for All Users
Resets the counter value for all the users.
• Print Counter List per User
Prints the counter value for each user.
• Clear Counter List per User
Resets the counter value for each user.
Downloaded from ManualsPrinter.com Manuals
63
System Settings
2
❖ Address Book Management
You can register, change or delete information registered in the Address
Book. For details, see “Address Book”.
• Names
You can register a name, key display, registration number, and title selection.
• Auth. Info
You can register a user code, and specify the functions available to each
user code. You can also register user names and passwords to be used
when sending e-mail, sending files to folders, or accessing an LDAP server.
• Protection
You can register a protection code.
• Fax Dest.
You can register a fax number, international TX mode, fax header, label insertion, IP-Fax destination, and protocol.
• E-mail
You can register an e-mail address.
• Folder
You can register the protocol, path, port number, and server name.
• Add to Group
You can put names registered in the Address Book into a group.
You can register up to 2,000 names.
You can register up to 100 user codes. If you add the optional user account
enhance unit, you can register up to 500 user codes.
You can also register and manage names in the Address Book using Web Image Monitor or SmartDeviceMonitor for Admin.
❖ Address Book: Program / Change / Delete Group
Names registered in the Address Book can be added into a group.
You can then easily manage the names registered in each group.
• Program / Change
You can register new groups, or changes a group name, key display, title
selection or registration number.
• Delete
You can delete a group from the Address Book.
You can register up to 100 groups.
You can also register and manage groups in the Address Book using Web Image Monitor or SmartDeviceMonitor for Admin.
64
Downloaded from ManualsPrinter.com Manuals
Administrator Tools
❖ Address Book: Program / Change / Delete Transfer Request
You can register fax destinations for the Transfer Request function in facsimile mode.
For details about operations, see “Registering the Transfer Request”.
• Program / Change
This registers new transfer requests and receiving stations, or changes the
transfer request name, key display, title selection, registration number, fax
destination, IP-Fax destination, e-mail address, or receiving station.
• Delete
Deletes a Transfer request.
You can register up 10 transfer requests.
2
❖ Address Book: Change Order
Changes the order of registered names.
You can rearrange the order of items on the same page, but you cannot move
items to another page.
For example, you cannot move an item from “PLANNING” ([OPQ]) to “DAILY” ([CD]).
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book: Change Order].
E Press the name key to be moved.
You can select a name using the number keys.
Downloaded from ManualsPrinter.com Manuals
65
System Settings
F
2
Press the name key in the place you want to move it to.
The user key is moved to the selected position, and the user key currently
at the selected position is moved forward or backward.
If you move the selected user key forward, the user key currently at the selected position is moved backward.
If you move the selected user key backward, the user key currently at the
selected position is moved forward.
You can also select a name using the number keys.
❖ Print Address Book: Destination List
You can print the destination list registered in the Address Book.
• Print in Title 1 Order
Prints the Address Book in Title 1 order.
• Print in Title 2 Order
Prints the Address Book in Title 2 order.
• Print in Title 3 Order
Prints the Address Book in Title 3 order.
• Print Group Dial List
Prints the group Address Book.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Print Address Book: Destination List].
E Select the print format.
F To print the list on two-sided pages, select [Print on 2 Sides].
G Press the {Start} key.
The list prints out.
66
Downloaded from ManualsPrinter.com Manuals
Administrator Tools
❖ Address Book: Edit Title
You can edit the title to easily find a user.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book: Edit Title].
E Press the title key you want to change.
F
G
2
Enter the new name, and then press [OK].
Press [OK].
❖ Address Book: Select Title
Specifies the title to select a name.
The default setting is Title 1.
❖ Auto Delete File in Document Server
Specify whether documents stored in the Document Server will or will not be
deleted after a specified period of time.
The default setting is Yes, After 3 day(s).
If you select [Yes], documents stored subsequently are deleted after the specified period.
If you select [No], documents are not automatically deleted.
If you select [Yes], enter a number of days from 1 to 180 (in 1 day increments).
The default is 3 days, this means documents are deleted 3 days (72 hours) after they are stored.
❖ Delete All Files in Document Server
You can delete files stored in the Document Server, including files stored for
Sample Print, Locked Print, Hold Print, and Stored Print under the printer
function.
Even if a password is always set, all documents are deleted.
A confirmation message appears. To delete all documents, select [Yes].
Downloaded from ManualsPrinter.com Manuals
67
System Settings
2
❖ Program / Change / Delete LDAP Server
Program the LDAP server to find up e-mail destinations in the LDAP server
Address Book directly. This function is possible when sending scan files by email using the scanner or fax function.
To start an LDAP search, make sure that the items listed below are set. For
other items, check your environment and make any necessary changes.
• Server Name
• Search Base
• Port No.
• Search Conditions
• Authentication method selection
To use the LDAP server in Administrator Tools, select [On] under LDAP server.
This function supports LDAP Version 2.0 and 3.0. Ver 2.0 does not support
High Security authentication.
❖ Use LDAP Server
Specify whether or not to use the LDAP server for searching.
The default setting is Off.
When Use LDAP Server is set to Off, [Search LDAP] will not appear on the
searching display.
❖ AOF (Always On)
Specify whether or not to use Auto Off.
The default setting is On.
❖ Firmware Version
You can check the version of the software installed in this machine.
❖ Network Security Level
For details about this function, consult your administrator.
❖ Delete All Logs
For details about this function, consult your administrator.
❖ Transfer Log Setting
For details about this function, consult your administrator.
❖ Data Security for Copying
For details about this function, consult your administrator.
Reference
p.3 “Accessing User Tools”
p.187 “Address Book”
p.201 “Printing the Counter for Each User”
p.250 “Registering the Transfer Request”
p.263 “Counter”
68
Downloaded from ManualsPrinter.com Manuals
Administrator Tools
Program / Change / Delete LDAP Server
This section describes how to specify the LDAP server settings.
To program / change the LDAP server
This section describes how to program / change the LDAP server.
2
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext] twice.
D Press [Program / Change / Delete LDAP Server].
E Check that [Program / Change] is selected.
F Select the LDAP server you want to program or change.
When programming the server, select [*Not Programmed].
G Set each item as necessary.
H Press [OK] after setting each item.
For details about LDAP server, see "Programming the LDAP server".
I Press [Exit].
J Press the {User Tools/Counter} key.
Reference
p.70 “Programming the LDAP server”
To delete the programmed LDAP server
This section describes how to delete the programmed LDAP server.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext] twice.
D Press [Program / Change / Delete LDAP Server].
E Press [Delete].
F Select the LDAP server you want to delete.
G Press [Yes].
H Press [Exit].
Downloaded from ManualsPrinter.com Manuals
69
System Settings
I Press the {User Tools/Counter} key.
Programming the LDAP server
This section describes how to specify the LDAP server settings.
2
To enter an identification name
This section describes how to enter a identification name.
A Press [Change] under "Identification Name".
Register a name for the LDAP server that will appear on the server selection
screen of the LDAP search operation.
B Enter the server’s identification name.
C Press [OK].
To enter a server name
This section describes how to enter a server name.
A Press [Change] under "Server Name".
Register the LDAP server’s host name or IP address.
B Enter the LDAP server name.
C Press [OK].
To enter the search base
This section describes how to enter the search base.
A Press [Change] under "Search Base".
Select a route folder to start the search from e-mail addresses registered in the
selected folder are search targets.
B Enter the search base.
For example, if the search target is the sales department of ABC company, enter “dc=sales department, o=ABC”. (In this example, the description is for an
active directory. “dc” is for the organization unit, and “o” is for the company.)
Search base registration may be required depending on your server environment. When registration is required, unspecified searches will result in error.
Check your server environment and enter any required specifications.
C Press [OK].
70
Downloaded from ManualsPrinter.com Manuals
Administrator Tools
To enter a port number
This section describes how to enter a port number.
A Press [Change] under "Port No.".
Specify the port number for communicating with the LDAP server. Specify a
port that is compliant with your environment.
2
B Enter the port number using the number keys, and then press the {q} key.
When SSL is set to [On], the port number automatically changes to “636”.
To start SSL communication
This section describes how to specify SSL communication.
A Press [On] under "Use Secure Connection (SSL).
Use SSL to communicate with the LDAP server.
To use SSL, the LDAP server must support SSL.
When SSL is set to [On], the port number automatically changes to “636”.
SSL setting must be enabled on this machine. For details, consult your network administrator.
To set authentication
This section describes how to specify authentication.
To make a search request to the LDAP server, use the administrator account for
authentication.
A Press [TNext].
B Press [On] or [High Security] under "Authentication".
Authentication settings must comply with your server’s authentication settings. Check your server settings before setting this machine.
[High Security] is available only with LDAP Version 3.0.
When [High Security] is selected, the administrator password is encrypted before it is sent to the network. When [On] is selected, the password is sent without encryption.
Downloaded from ManualsPrinter.com Manuals
71
System Settings
To enter the user name and password
2
This section describes how to enter the user name and password.
When [On] or [High Security] is selected for the authentication setting, use the administrator account name and password. Do not enter the administrator account
name and password when using authentication for each individual or each
search.
A Press [TNext].
B Press [Change] under "User Name".
C Enter the user name, and then press [OK].
Procedures for the user name setting differ depending on server environment. Check your server environment before making the setting.
Example: Domain Name\User Name, User Name@Domain Name,
CN=Name, OU=Department Name, DC=Server Name
D Press [Change] under "Password”.
E Enter the password, and then press [OK].
The user name and password are required for administrator authentication to
access the LDAP server.
You can set the user name and password in this machine’s Address Book to
allow individual authentication access to the LDAP server. Use Administrator Tools to select the user name and password you want to use.
To test the connection
This section describes how to test the connection.
Access the LDAP server to check the proper connection is established. Check authentication works according to the authentication settings.
A Press [Connection Test].
A connection test is carried out.
B Press [Exit].
If the connection test fails, check your settings and try again.
This function does not check search conditions or the search base.
72
Downloaded from ManualsPrinter.com Manuals
Administrator Tools
To set search conditions
This section describes how to specify search conditions.
You can enter an attribute as a typical search keyword. Using the entered attribute, the function searches the LDAP server’s Address Book.
A Press [TNext] twice.
B Press [Change] for items you want to use as search conditions from the fol-
2
lowing: "Name", "E-mail Address", "Fax Number", "Company Name", and
"Department Name".
C Enter the attribute you want to use when searching for e-mail addresses,
and then press [OK].
The attribute value may change depending on the server environment. Check
the attribute value complies with your server environment before setting it.
You can leave items blank, but you cannot leave attributes blank when
searching for e-mail addresses from the LDAP server Address Book.
To set search options
This section describes how to specify search options.
To search the LDAP server data using a keyword other than prepared keywords
such as Name, E-mail Address, FAX Number, Company Name, and Department
Name, specify the attribute for the keyword registered in your LDAP server, and
the name to be displayed on the control panel during the search. For example, to
search e-mail addresses by employee number, enter “employeeNo.” in the Attribute field, and “Employee No.” in the key display field.
A Press [TNext] three times.
B Press [Change] under "Attribute".
C Enter the attribute you want to use when searching for e-mail addresses,
and then press [OK].
The attribute value may change depending on the server environment. Check
the attribute complies with your server environment before setting it.
D Press [Change] under "Key Display".
Downloaded from ManualsPrinter.com Manuals
73
System Settings
E Enter the key display, and then press [OK].
The registered “key display” appears as a keyword for searching LDAP.
• Without key display registration
2
• With key display registration
The key does not appear on the search screen unless both “Attribute” and
“Key Display” are registered. Make sure you register both to use the optional
search.
74
Downloaded from ManualsPrinter.com Manuals
3. Copier / Document Server
Features
This chapter describes user tools in the Copier / Document Server Features
menu. For details on how to access Copier / Document Server Features, see "Accessing User Tools".
General Features
This section describes the user tools in the General Features menu under Copier /
Document Server Features.
Default settings are shown in bold type.
❖ Auto Paper Select Priority
Auto Paper Select is the default setting. You can cancel this setting.
The default setting is On.
❖ Auto Tray Switching
If you load paper of the same size in two or more trays, the machine automatically shifts to the other when the first tray runs out of paper (when Auto Paper Select is selected.) This function is called “Auto Tray Switching”. This
setting specifies whether to use Auto Tray Switching or not.
• With Image Rotation
Use to copy when using the Auto Tray Switching function.
• Without Image Rotation
Only copies with Auto Tray Switching if you load paper of the same size
and in the same orientation in two or more trays. If the paper is not the
same size or in the same orientation, copying is interrupted and the message “Load paper.” is displayed.
• Off
When a paper tray runs out of paper, copying is interrupted and the message “Load paper.” is displayed.
The default setting is With Image Rotation.
❖ Paper Display
You can choose to have the available paper trays and sizes shown on the initial display.
The default setting is Display.
If you select [Hide], the display is shown as below. Press [Auto Paper Select] to
display paper sizes.
Downloaded from ManualsPrinter.com Manuals
75
Copier / Document Server Features
❖ Original Type Priority
You can select the original type effective when the power is turned on, or
modes cleared.
The default setting is Text.
❖ Original Type Display
You can have the original types shown on the initial display.
The default setting is Display.
If you select [Hide], the display is as below.
3
❖ Auto Image Density Priority
You can set whether Auto Image Density is "On" or "Off" when the machine
is turned on, reset, or modes are cleared.
The default setting for "Text" is On.
The default setting for "Text/Photo" is On.
The default setting for "Photo" is Off.
The default setting for "Pale" is On.
The default setting for "Generation Copy" is On.
76
Downloaded from ManualsPrinter.com Manuals
General Features
❖ Copy Quality
You can adjust the quality level of copies for each original type (Text,
Text/Photo, Photo, Pale, Generation Copy).
• Text
Adjust text sharpness.
The default setting is Normal.
"Custom Setting" is the value set during service setup.
Choosing "Sharp" or "Sort" affects the outline sharpness of text.
• Text/Photo
When there are photo(s) and text on the original, select which takes priority.
The default setting is Normal.
"Custom Setting" is the value set during service setup.
"Normal" gives a balanced text and photo reproduction.
• Photo
For a photo original, adjust the finish quality level to match the type of
photo original.
The default setting is Print Photo.
"Custom Setting" is the value set during service setup.
Select "Print Photo" for printed photo originals, and "Glossy Photo" for
printed photo originals with fine dots.
Select "Normal" for printed photo and text originals.
• Pale
Adjust the quality level for the finish of a pale original with normal density.
The default setting is Normal.
"Custom Setting" is the value set during service setup.
• Generation Copy
Adjust the quality level so as not to thicken the lines of the finish image.
The default setting is Normal.
"Custom Setting" is the value set during service setup.
3
❖ Image Density
You can select one of seven original image density levels for each original
type (Text, Text/Photo, Photo, Pale, Generation Copy).
The default setting for "Text" is Normal.
The default setting for "Text/Photo" is Normal.
The default setting for "Photo" is Normal.
The default setting for "Pale" is Normal.
The default setting for "Generation Copy" is Normal.
❖ Duplex Mode Priority
You can select the type of the Duplex function effective when the power is
turned on, or modes cleared.
The default setting is 1 Sided→1 Sided (Metric version) / 1 Sided→2 Sided
(Inch version)
Downloaded from ManualsPrinter.com Manuals
77
Copier / Document Server Features
❖ Copy Orientation in Duplex Mode
You can set the copy orientation when making two-sided copies.
The default setting is Top to Top.
❖ Original Orientation in Duplex Mode
You can set the original orientation when making two-sided copies.
The default setting is Top to Top.
3
❖ Change Initial Mode
You can select standard mode or Program No.10 as the mode effective when
power is turned on, or modes cleared.
The default setting is Standard.
❖ Max. Copy Quantity
The maximum copy quantity can be set between 1 and 999.
The default setting is 999 sheet(s).
❖ Tone: Original Remains
The beeper (key tone) sounds if you forget to remove originals after copying.
The default setting is On.
If Panel Tone of User Tools (System Settings) is [Off] the beeper does not
sound irrespective of the Tone: Original Remains setting.
❖ Job End Call
You can choose whether or not the beeper sounds when copying is complete.
The default setting is On.
If Panel Tone of User Tools (System Settings) settings is [On], the machine
beeps to notify you that it did not complete a job for reasons such as copying
was interrupted, the paper tray ran out of paper, or a paper jam occurred.
❖ Copy Function Key: F1-F5
You can assign frequently used functions to function keys F1 to F5.
The default setting for "Copy Function Key: F1" is 1 Sided→2 Sided: T to T.
The default setting for "Copy Function Key: F2" is 2 Sided: T to T→2 Sided: T
to T.
The default setting for "Copy Function Key: F3" is 1 Sided→1 Sided Combine.
The default setting for "Copy Function Key: F4" is 1 Sided→1 Sided Combine: 4
originals.
The default setting for "Copy Function Key: F5" is Create Margin.
78
Downloaded from ManualsPrinter.com Manuals
General Features
❖ Document Server Storage Key: F1-F5
You can assign frequently used functions to function keys F1 to F5. You can
also change assigned functions.
The default setting for "Document Server Storage Key: F1" is 2 Sided Original
Top to Top.
The default setting for "Document Server Storage Key: F2" is 1 Sided→1 Sided
Combine.
The default setting for "Document Server Storage Key: F3" is 1 Sided→1 Sided
Combine: 4 originals.
The default setting for "Document Server Storage Key: F4" is 1 Sided→1 Sided
Combine: 8 originals.
The default setting for "Document Server Storage Key: F5" is Create Margin.
3
Reference
p.3 “Accessing User Tools”
p.41 “Warm Up Notice (copier/Document Server)”
"Selecting the Original Type Setting", Copy/ Document Server Reference
"Adjusting Copy Image Density", Copy/ Document Server Reference
"Selecting Copy Paper", Copy/ Document Server Reference
Downloaded from ManualsPrinter.com Manuals
79
Copier / Document Server Features
Reproduction Ratio
This section describes the user tools in the Reproduction Ratio menu under Copier / Document Server Features.
Default settings are shown in bold type.
3
❖ Shortcut R / E
You can register up to three frequently used Reduce/Enlarge ratios other
than the fixed Reduce/Enlarge ratio and have them shown on the initial display. You can also change registered Reduce/Enlarge ratios.
If no Reduce/Enlarge ratio has been set when selecting [Shortcut R / E] 1,
[Shortcut R / E] 2, or [Shortcut R / E] 3, enter the ratio using the number keys.
❖ Enlarge1-5
You can customize available enlargement ratios by pressing [Reduce / Enlarge],
followed by [Enlarge].
The default setting for "Enlarge 1" is 115% (Metric version) / 121% (Inch version).
The default setting for "Enlarge 2" is 122% (Metric version) / 129% (Inch version).
The default setting for "Enlarge 3" is 141% (Metric version) / 155% (Inch version).
The default setting for "Enlarge 4" is 200% (Metric version) / 200% (Inch version).
The default setting for "Enlarge 5" is 400% (Metric version) / 400% (Inch version).
When selecting [User Enlrg. Ratio], enter a ratio using the number keys (in the
range of 101 to 400%).
❖ Priority Setting: Enlarge
You can set the ratio with priority when [Reduce / Enlarge] is pressed, followed
by [Enlarge].
The default setting is 141% (Metric version) / 155% (Inch version).
80
Downloaded from ManualsPrinter.com Manuals
Reproduction Ratio
❖ Reduce1-6
You can customize available reduction ratios by pressing [Reduce / Enlarge],
followed by [Reduce].
The default setting for "Reduce 1" is 25% (Metric version) / 25% (Inch version).
The default setting for "Reduce 2" is 50% (Metric version) / 50% (Inch version).
The default setting for "Reduce 3" is 65% (Metric version) / 65% (Inch version).
The default setting for "Reduce 4" is 71% (Metric version) / 73% (Inch version).
The default setting for "Reduce 5" is 75% (Metric version) / 78% (Inch version).
The default setting for "Reduce 6" is 82% (Metric version) / 85% (Inch version).
When selecting [User Redc.Ratio], enter a ratio using the number keys (in the
range of 25 to 99%).
3
❖ Priority Setting: Reduce
You can set the ratio with priority when [Reduce / Enlarge] is pressed, followed
by [Reduce].
The default setting is 71% (Metric version) / 73% (Inch version).
❖ Ratio for Create Margin
You can set a Reduce/Enlarge ratio when registering Create Margin in a
shortcut key.
The default setting is 93%.
Enter a ratio using number keys (in the range of 90 to 99%).
❖ R / E Priority
Specifies which tab has priority on the display panel when [Reduce / Enlarge]
is pressed.
The default setting is Reduce.
Reference
p.3 “Accessing User Tools”
Downloaded from ManualsPrinter.com Manuals
81
Copier / Document Server Features
Edit
3
This section describes the user tools in the Edit menu under Copier / Document
Server Features.
Default settings are shown in bold type.
Enter the width of the binding margin with the number keys as follows:
• Metric version: 0–30 mm (in increments of 1 mm)
• Inch version: 0"-1.2" (in increments of 0.1 inch)
Enter the width of the erased margin with the number keys as follows:
• Metric version: 2–99 mm (in increments of 1 mm)
• Inch version: 0.1"-3.9" (in increments of 0.1 inch)
An image of approximately 1.5 mm (0.06”) will not be displayed as the width of
the separation line, when specifying solid or broken lines.
❖ Front Margin: Left / Right
Specify left and right margins on the front side of copies in Margin Adjustment mode.
The default setting is Left 5 mm (Metric version) / Left 0.2" (Inch version).
❖ Back Margin: Left / Right
Specify left and right margins on the back side of copies in Margin Adjustment mode.
The default setting is Right 5 mm (Metric version) / Right 0.2" (Inch version).
❖ Front Margin: Top / Bottom
Specify top and bottom margins on the front side of copies in Margin Adjustment mode.
The default setting is T / B 0mm (Metric version) / T / B 0.0" (Inch version).
❖ Back Margin: Top / Bottom
Specify top and bottom margins on the back side of copies in Margin Adjustment mode.
The default setting is T / B 0mm (Metric version) / T / B 0.0" (Inch version).
❖ 1 Sided→2 Sided Auto Margin: TtoT
When using the 1 sided → 2 sided Duplex function, you can specify margins
on the back side.
The margin is set to the same value of “Back Margin: Left/Right".
The default setting is Right 5 mm (Metric version) / Right 0.2" (Inch version).
❖ 1 Sided→2 Sided Auto Margin: TtoB
When using the 1 sided → 2 sided Duplex function, you can specify margins
on the back side.
The value set for "Back Margin: Top/Bottom" is used.
The default setting is T / B 0 mm (Metric version) / T / B 0.0" (Inch version).
82
Downloaded from ManualsPrinter.com Manuals
Edit
❖ Erase Border Width
Specify the width of erased border margins using this function.
The default setting is 10 mm (Metric version) / 0.4" (Inch version).
❖ Erase Original Shadow in Combine
In Combine Copy or Booklet/Magazine Copy mode, you can specify whether
to erase a 3mm, 0.1" bounding margin around all four edges of each original.
The default setting is Yes.
❖ Erase Centre Width
Specify the width of the erased centre margins with this function.
The default setting is 10 mm (Metric version) / 0.4" (Inch version).
3
❖ Image Repeat Separation Line
You can select a separation line using the Image Repeat function from: None,
Solid, Broken A, Broken B, or Crop Marks.
• None
• Solid
• Broken A
• Broken B
• Crop Marks
The default setting is None.
Selecting solid or broken lines might produce a blank area of approximately
1.5 mm (0.06") in width along the separation line.
Downloaded from ManualsPrinter.com Manuals
83
Copier / Document Server Features
❖ Double Copies Separation Line
You can select a separation line using the Double Copies function from: None,
Solid, Broken A, Broken B, or Crop Marks.
• None
• Solid
3
• Broken A
• Broken B
• Crop Marks
The default setting is None.
Selecting solid or broken lines might produce a blank area of approximately
1.5 mm (0.06") in width along the separation line.
84
Downloaded from ManualsPrinter.com Manuals
Edit
❖ Separation Line in Combine
You can select a separation line using the Combine function from: None, Solid, Broken A, Broken B, or Crop Marks.
• None
• Solid
3
• Broken A
• Broken B
• Crop Marks
The default setting is None.
Selecting solid or broken lines might produce a blank area of approximately
1.5 mm (0.06") in width along the separation line.
❖ Copy on Designating Paper
Specify whether to copy onto slip sheets.
The default setting is Yes.
❖ Front Cover Copy in Combine
You can make a combined copy on the front cover sheet when you select
Front Cover mode.
GCST019E
The default setting is Combine.
❖ Copy on Designating Page in Combine
Specify whether to make a combined copy on the inserted slip sheets in
Desig./Chapter mode.
The default setting is Combine.
Downloaded from ManualsPrinter.com Manuals
85
Copier / Document Server Features
❖ Orientation: Booklet, Magazine
You can select the opening orientation of copies when using Booklet or Magazine mode.
The default setting is Open to Left.
❖ Copy Order in Combine
You can set the copy order in Combine mode to Left to Right or Top to Bottom.
3
GCAH090E
The default setting is From Left to Right.
Reference
p.3 “Accessing User Tools”
"Booklet/Magazine", Copy/ Document Server Reference
86
Downloaded from ManualsPrinter.com Manuals
Stamp
Stamp
This section describes the user tools in the Stamp menu under Copier / Document Server Features.
Default settings are shown in bold type.
Background Numbering
This section describes the user tools in the Background Numbering menu under
Stamp.
3
❖ Size
You can set the size of the numbers.
The default setting is Normal.
❖ Density
You can set the density of the numbers.
The default setting is Normal.
Preset Stamp
This section describes the user tools in the Preset Stamp menu under Stamp.
❖ Stamp Priority
You can select the stamp type given priority when [Preset Stamp] is pressed.
The default setting is Copy.
❖ Stamp Language
You can select the language of the message printed in Stamp mode.
The default setting is English.
❖ Stamp Position
You can set the position where the stamp is printed.
Press the arrow keys to adjust the position.
The default setting for "Position" is Top Right.
The default setting for "Top Margin" is 24 mm (Metric version) / 1.0" (Inch
version).
The default setting for "Right Margin" is 24 mm (Metric version) / 1.0" (Inch
version).
Downloaded from ManualsPrinter.com Manuals
87
Copier / Document Server Features
3
❖ Stamp Format
You can adjust the stamp's size, density, and print page.
• Size
You can set the size of the stamp.
The default setting is 1X.
• Density
You can set the pattern used to print the stamp.
The default setting is Normal.
Normal: The stamp is printed on the image. You cannot check which parts
will overlap.
Lighter: The image can be seen through the stamp.
Lightest: You can see the image even clearer than in the Lighter setting.
• Page to Stamp
You can have the stamp printed on the first page or all pages.
The default setting is All Pages.
Reference
"Preset Stamp", Copy/ Document Server Reference
User Stamp
This section describes the user tools in the User Stamp menu under Stamp.
❖ Program / Delete Stamp
You can register, change, or delete user stamps.
You can register up to four custom stamps with your favourite designs.
❖ Stamp Position 1-4
Specify position where the stamp is printed.
Press the arrow keys to adjust the position.
The default setting for "Position" is Top Right.
The default setting for "Top Margin" is 24 mm (Metric version) / 1.0" (Inch
version).
The default setting for "Right Margin" is 24 mm (Metric version) / 1.0" (Inch
version).
❖ Stamp Format 1-4
You can adjust the print page for User Stamps 1 to 4 already registered.
• Page to Stamp
Sets whether to print the stamp on all pages or only the first page.
The default setting is All Pages.
Reference
"User Stamp", Copy/Document Server Reference
88
Downloaded from ManualsPrinter.com Manuals
Stamp
Date Stamp
This section describes the user tools in the Date Stamp menu under Stamp.
❖ Format
You can select the date format for the Date Stamp function.
The default setting is DD / MM / YYYY (Metric version) / MM / DD / YYYY
(Inch version).
❖ Font
You can select the Date Stamp font.
The default setting is Font 1.
This setting is linked to the Page Numbering function.
3
❖ Stamp Position
You can set the position where the stamp is printed.
Press the arrow keys to adjust the position.
The default setting for "Position" is Top Left.
The default setting for "Top Margin" is 8 mm (Metric version) / 0.3" (Inch version).
The default setting for "Left Margin" is 32 mm (Metric version) / 0.8" (Inch
version).
❖ Stamp Setting
You can have the date printed on the first page or all pages.
The default setting is All Pages.
❖ Size
You can set the Date Stamp size.
The default setting is Auto.
❖ Superimpose
You can have the Date Stamp printed in white when it overlaps black parts of
the image.
The default setting is No.
Downloaded from ManualsPrinter.com Manuals
89
Copier / Document Server Features
Page Numbering
This section describes the user tools in the Page Numbering menu under Stamp.
❖ Stamp Format
You can select the page number format given priority when [Page Numbering]
is pressed.
The default setting is P1, P2.
3
❖ Font
You can select the page number printed in Page Numbering mode.
The default setting is Font 1.
❖ Size
You can set the size of the stamp printed in Page Numbering mode.
The default setting is Auto.
❖ Duplex Back Page Stamping Position
You can set the position of the duplex back page number printed in Duplex
mode.
The default setting is Opposite Position.
❖ Page Numbering in Combine
You can set page numbering when using the Combine function and the Page
Numbering function together.
The default setting is Per Original.
❖ Stamp on Designating Slip Sheet
You can print the page number onto slip sheets when using the Designate
function and the Page Numbering function together.
The default setting is No.
❖ Stamp Position
P1, P2... Stamp Position: 1/5, 2/5... Stamp Position: –1–, –2–... Stamp Position:
P.1, P.2. Stamp Position: 1, 2... Stamp Position: 1–1, 1–2...
You can set the position where the stamp is printed.
Press the arrow keys to adjust the position.
❖ Superimpose
You can have page numbers printed in white when they overlap black parts
of the image.
The default setting is No.
❖ Page Numbering Initial Letter
You can select the page numbering initial letter between”P1, P2.../ P.1, P.2...”
and ”S1, S2.../ S.1, S.2...”
The default setting is P1, P2.../ P.1, P.2....
Reference
p.3 “Accessing User Tools”
90
Downloaded from ManualsPrinter.com Manuals
Input/Output
Input/Output
This section describes the user tools in the Input/Output menu under Copier /
Document Server Features.
Default settings are shown in bold type.
❖ Switch to Batch
You can select to have Batch mode or SADF mode displayed when you press
the [Special Original] key.
The default setting is Batch.
3
❖ SADF Auto Reset
When you set one original at a time in the ADF, the Auto Feed indicator lights
for a specified time after an original is fed, to show the ADF is ready for another original.
You can adjust this time from 3 to 99 seconds in increments of 1 second.
The default setting is 5 seconds.
❖ Rotate Sort: Auto Paper Continue
Specify to continue copying when paper of the required orientation has run
out during rotate sort.
The default setting is No.
• Yes
Copying continues using copy paper of a different orientation. The copy
job will finish even if you have left the machine.
• No
When paper of the required orientation runs out, the machine stops copying and prompts you to supply copy paper. After you have loaded paper,
the machine will continue copying.
❖ Auto Sort
You can specify whether the Sort function is selected when the machine is
turned on, or the functions are cleared.
The default setting is No.
❖ Memory Full Auto Scan Restart
When memory becomes full while scanning originals, the machine can make
copies of scanned originals first, and then automatically proceed scanning remaining originals.
The default setting is No.
• Yes
You can leave the machine unattended to make copies, but sorted pages
will not be sequential.
• No
When memory becomes full, the machine stops operation allowing you to
remove the copy pages delivered on the output tray.
Downloaded from ManualsPrinter.com Manuals
91
Copier / Document Server Features
❖ Select Stack Function
Specify whether Stack or Rotate Sort has priority on the initial display.
The default setting is Stack.
An optional finisher is required to use this function.
3
❖ Select Stapling Position
Specify which Top 2 staples or Bottom shown on the initial display with priority.
The optional 2 Tray finisher or booklet finisher is required to use this function.
The default setting is Top 2.
❖ Select Punch Type
Specify which punch type (2 holes or 3 holes) has priority to be shown on the
initial display.
The optional 2 Tray finisher equipped with the punch function is required.
The default setting is 2 Holes.
❖ Letterhead Setting
If you select [Yes] in this function, the machine rotates the image correctly.
Orientation-fixed (top to bottom) or two-sided paper might not be printed
correctly depending on how the originals and paper are placed.
The default setting is No.
Reference
p.3 “Accessing User Tools”
"Orientation-Fixed Paper or Two-Sided Paper", Troubleshooting
"Batch mode", Copy/ Document Server Reference
"Sort", Copy/ Document Server Reference
92
Downloaded from ManualsPrinter.com Manuals
Settings for the Document Server
Settings for the Document Server
This section describes user tool settings for the Document Server.
For details, see "System Settings", and "Copier / Document Server Features".
❖ Copier / Document Server Features
Heading
items
Default
General Features
Document Server Storage Key: F1
2 Sided Original
Top to Top
General Features
Document Server Storage Key: F2
1 Sided→1 Sided
Combine
General Features
Document Server Storage Key: F3
1 Sided→1 Sided
Combine: 4 originals
General Features
Document Server Storage Key: F4
1 Sided→1 Sided
Combine: 8 originals
General Features
Document Server Storage Key: F5
Create Margin
Heading
Item
Default
General Features
Warm up Notice
On
General Features
Copy Count Display
Up
General Features
Output: Document Server
Internal Tray 1
3
❖ System Settings
Tray Paper Settings Paper Tray Priority: Copier
Tray 1
Tray Paper Settings Cover Sheet Tray
Off
Tray Paper Settings Slip Sheet Tray
Off
Timer Settings
Copier/Document Server Auto Reset Timer
60 seconds
Administrator
Tools
Auto Delete File in Document Server
Yes, After 3 day(s)
Administrator
Tools
Delete All Files in Document Server
-
Reference
p.41 “System Settings”
p.75 “Copier / Document Server Features”
Downloaded from ManualsPrinter.com Manuals
93
Copier / Document Server Features
3
94
Downloaded from ManualsPrinter.com Manuals
4. Facsimile Features
This chapter describes user tools in the Facsimile Features menu. For details on
how to access Facsimile Features, see "Accessing User Tools".
General Settings/Adjustment
This section describes the user tools in the General Settings/Adjustment menu
under Facsimile Features.
❖ Memory / Immed. Transmission Switch
Specify the Transmission Mode for document transmission.
The default setting is Memory Transmission.
❖ Text Size Priority
Specify the character size of your originals for scanning.
The default setting is Standard.
❖ Original Type Priority
Specify the type of originals for scanning.
The default setting is Text.
❖ Auto Image Density
Use this function to prioritize automatic Image Density for scanning your
originals.
The default setting is On.
❖ Adjust Scan Density
Specify the scan density of your originals.
The default setting is Level 4.
❖ Select Title
Use this function for selecting the title to be shown on the destination list.
The default setting is Title 1.
❖ Change Initial Mode
Select whether contents registered in program No.1 are to be used as the initial settings after the power is turned on or the {Clear Modes} key is pressed.
The default setting is Standard.
You cannot select Program No.1 if program No.1 has not been programmed
with priority functions.
❖ Adjust Sound Volume
Adjust the sound volume during On Hook Mode and Immediate Transmission.
The default settings for each sound volume are Level 2.
Downloaded from ManualsPrinter.com Manuals
95
Facsimile Features
❖ Program Fax Information
Program information to be shown on the display of the other machine and
printed as a report. Fax Header,Own Name, and Own Fax Number can be
programmed.
For details about how to program Fax Information, see "Registering Fax Information".
❖ Scan End Reset
Use this function to return to the initial settings each time an original is
scanned.
The default setting is On.
4
❖ TX Stamp Priority
Use this function to press a TX stamp.
The default setting is Off.
❖ Line Priority Setting
Specify the line to be used.
The display may differ depending on the line type you have.
❖ Program Economy Time
Specifying a time for transmission when call charges are low.
You can program only one Economy Time.
The default setting is 23:00.
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then try again.
❖ On Hook Mode Release Time
Specify a time to cancel On Hook mode after you transmit using On Hook dialing.
The default setting is 3 minutes.
96
Downloaded from ManualsPrinter.com Manuals
General Settings/Adjustment
❖ Quick Operation Key 1-3
Frequently used functions programmed as Quick Operation keys are shown
on the menu immediately after the power is turned on.
The Quick Operation keys can be programmed with the following functions:
• Journal
• TX File Status (Transmission File Status)
• Print Conf. RX (Print Confidential Reception)
• Print Memory Lock
• Stored File
• Send Later
• Auto Document
• 2 Sided Original
• Closed Network
• Polling TX (Polling Transmission)
• Polling RX (Polling Reception)
• Fax Header Print
• Label Insertion
• RX File Status (Reception File Status)
• Forwarding
• Transfer Request
• Switch RX Mode (Reception Mode Switch)
• Manual E-mail RX
(when the Internet Fax is set to ON.)
• TX Status Report (Transmission Status Report)
• Sender Settings
• E-mail TX Results (E-mail Transmission Results)
Up to three functions can be programmed to a Quick Operation keys.
The default setting for Quick Operation key 1 has not been set.
The default setting for Quick Operation key 2 is TX File Status.
The default setting for Quick Operation key 3 is RX File Status.
A Press [Facsimile Features].
B Press [Gen. Settings/ Adjust].
C Press [TNext].
D Press [Quick Operation Key 1-3].
Select the Quick Operation Key 1-3 you want to program.
Downloaded from ManualsPrinter.com Manuals
4
97
Facsimile Features
E
Select the function you want to program to the Quick Operation Key.
F
Functions that appear dimmed have already been set.
Press [OK].
Press the {User Tools/Counter} key.
G
Reference
p.3 “Accessing User Tools”
4
p.115 “Registering Fax Information”
"Adjusting the Volume", Troubleshooting
"Sending at a Specific Time (Send Later)", Facsimile Reference
"Fax Header Print", Facsimile Reference
"Reading the Display", Facsimile Reference
98
Downloaded from ManualsPrinter.com Manuals
Reception Settings
Reception Settings
This section describes the user tools in the Reception Settings menu under Facsimile Features.
❖ Switch Reception Mode
Specify the method for receiving fax documents.
The default setting is Auto Reception.
❖ Authorized RX (Authorized Reception)
Specify whether or not unwanted fax documents are to be screened out.
The default setting is Off.
❖ Forwarding
Specify whether or not received fax documents are to be forwarded to a programmed receiver.
The default setting is Off.
4
❖ RX File Print Qty (Reception File Print Quantity)
Specify the number of copies to be printed for each fax document received.
The default setting is 1 set(s).
• 1 to 10 set(s)
❖ 2 Sided Print
Specify whether or not received fax documents are to be printed on both sides
of the paper.
The default setting is Off.
❖ RX Reverse Printing (Reception Reverse Printing)
Specify whether or not received fax documents are to be printed from the last
page received.
The default setting is Off.
❖ Paper Tray
Use this function to print fax documents received from programmed senders
and fax documents from other senders, using different paper trays.
The default setting is Auto Select.
Display of tray names may differ depending on the options installed.
❖ Specify Tray for Lines
Specify a paper tray for each line (telephone, Internet Fax, IP-Fax).
The default setting is Off.
A Press [Facsimile Features].
B Press [Reception Settings].
C Press [Specify Tray for Lines].
Downloaded from ManualsPrinter.com Manuals
99
Facsimile Features
4
D
Select [On] to select a paper tray.
E
If you select [Off], the received fax is delivered to a default tray.
Select the line type.
F
Select a tray to deliver the received paper onto, and then press [OK] twice.
G
If you want to specify another line type, repeat from step E.
Press the {User Tools/Counter} key.
❖ Checkered Mark
Specify whether or not a checkered mark is to be printed on the first page of
received fax documents.
The default setting is On.
❖ Centre Mark
Specify whether or not a centre mark is to be printed halfway down the left
side and at the top centre of each page received.
The default setting is On.
❖ Print Reception Time
Specify whether or not the received date, time, and file number are printed at
the bottom of received fax documents.
The default setting is Off.
Reference
p.3 “Accessing User Tools”
p.42 “Output: Facsimile (facsimile)”
100
Downloaded from ManualsPrinter.com Manuals
E-mail Settings
E-mail Settings
This section describes the user tools in the E-mail Settings menu under Facsimile
Features.
❖ Internet Fax Settings
You can select to display
set On to display the icon.
The default setting is Off.
or not. When you want to send an Internet Fax,
❖ Max. E-mail Size
When the other party has a limit on the size of e-mail messages that can be
received, or sending data heavy e-mail causes problems, you can make settings to limit the size of sent e-mail. When this function is set to on, transmission of e-mail that exceeds the set size is aborted.
The default setting is Off.
When e-mail exceeds the maximum file size, an Error Report is output, and
the e-mail is deleted.
Even when e-mail does not exceed the size limit, it may be rejected if it does
not meet the requirements of the server settings.
A Press [Facsimile Features].
B Press [E-mail Settings].
C Press [Max. E-mail Size].
D Press [On].
E
F
G
4
Enter the maximum e-mail size using the number keys.
Maximum e-mail size can be between 64 and 102,400 KB.
If you make a mistake, press [Clear] or the {Clear/Stop} key, and then enter
again.
Press [OK].
Press the {User Tools/Counter} key.
Downloaded from ManualsPrinter.com Manuals
101
Facsimile Features
4
❖ SMTP RX File Delivery Settings (SMTP Reception File Delivery Settings)
This function is available on systems that allow routing of e-mail received via
SMTP.
When an authorized e-mail address is set, e-mail received from addresses that
do not match the authorized address is discarded, and an error message is returned to the SMTP server.
The authorized e-mail address is compared with the addresses of e-mail originators, as illustrated by the following examples.
• When the authorized e-mail address is set to “@aaa.abcd.com”:
abc@aaa.abcd.com - accepted
def@aaa.xyz.com - not accepted
abc@abcd.com - not accepted
No Error Report is output even when e-mail is discarded.
The default setting is Off.
A Press [Facsimile Features].
B Press [E-mail Settings].
C Press [SMTP RX File Delivery Settings].
D Press [On].
E
Press [Change], and then enter the sending e-mail address to be authorized.
F
If you make a mistake, press [Backspace] or [Clear], and then enter again.
Press [OK] twice.
Press the {User Tools/Counter} key.
G
102
Downloaded from ManualsPrinter.com Manuals
IP-Fax Settings
IP-Fax Settings
This section describes the user tools in the IP-Fax Settings menu under Facsimile
Features.
❖ Enable H.323
Specify whether or not H.323 is used for IP-Fax transmission.
The default setting is Off.
❖ Enable SIP
Specify whether or not SIP is used for IP-Fax transmission.
The default setting is Off.
❖ H.323 Settings
Set the IP address or host name of gate keeper, and alias telephone number.
If you select [On] using the User Parameters, you can use the gatekeeper server.
See “Parameter Settings” ( switch 34, bit 0).
You can use numbers, and symbols (“#” and “*”) for registration of the alias
telephone number in H.323 Settings. Make sure you enter these characters
correctly.
A Press [Facsimile Features].
B Press [IP-Fax Settings].
C Press [H.323 Settings].
D
Press [Change] for each property.
E
Enter the IP address or host name, and alias telephone number and press
[OK].
Press [OK].
Press the {User Tools/Counter} key.
F
G
Downloaded from ManualsPrinter.com Manuals
4
103
Facsimile Features
4
❖ SIP Settings
Set the SIP server's IP address or host name, and SIP user name.
If you select [On] using the User Parameters, you can use the SIP server. See
“Parameter Settings” ( switch 34, bit 1).
You can use alphanumeric symbols (lower and upper cases) and symbols (";",
"?", ":", "&", "=", "+", "$", ",", "-", "_", ".", "!", "~", "*", "#", "‘", "(", ")", "%", "/", and
"@") for registration of the SIP User Name in SIP Settings. Make sure you enter
these characters correctly.
Use numbers and periods (“.”) to enter the correct IP addresses for the gatekeeper, SIP server, and gateway. To obtain the correct IP addresses, consult
the administrator.
A Press [Facsimile Features].
B Press [IP-Fax Settings].
C Press [SIP Settings].
D
Press [Change] for each property.
E
A proxy server relays call requests and responses.
A redirect server processes request destination inquiries.
A register server registers location information of user agents (which correspond to telephones or facsimiles on public telephone lines) on an IP network.
Enter the IP address or host name, and SIP user name, and then press [OK].
F
G
Press [OK].
Press the {User Tools/Counter} key.
104
Downloaded from ManualsPrinter.com Manuals
IP-Fax Settings
❖ Program / Change / Delete Gateway
Register, change, or delete the gateway used for transmission to IP-Fax.
Program / Change:
A Press [Facsimile Features].
B Press [IP-Fax Settings].
C Press [Program / Change / Delete Gateway].
D
E
Check that [Program / Change] is selected.
Press a gateway to register.
F
When registering a new gateway, press [*Not Programmed].
Press [Change] for “Prefix”.
G
H
I
4
Enter the Prefix using the number keys, and then press [OK].
To change the existing prefix, press [Clear], and then enter a new prefix.
For documents sent using a gateway to G3 Fax, prefixes can be used. If the
first several digits of IP-Fax number and the gateway- specific prefix are
identical, documents can be transmitted using the registered digits of the
gateway. For example, if both 03 and 04 have been registered as gateway
number while 0312345678 is also specified, documents can be transmitted
via a gateway for which 03 is used as a prefix.
When you wish to use the gateways regardless of the IP-Fax destination
numbers, register only the gateway addresses without registering the prefix.
Select a protocol.
Press [Change] for Gateway Address.
Downloaded from ManualsPrinter.com Manuals
105
Facsimile Features
J
Enter the gateway address, and then press [OK].
K
Press [OK].
Press the {User Tools/Counter} key.
L
4
Delete:
A Press [Facsimile Features].
B Press [IP-Fax Settings].
C Press [Program / Change / Delete Gateway].
D Press [Delete], and then select a gateway to delete.
E
F
G
Press [Delete] on the confirmation message.
If you do not want to delete the gateway you have selected, press [Do not
Delete].
Press [Exit].
Press the {User Tools/Counter} key.
106
Downloaded from ManualsPrinter.com Manuals
Administrator Tools
Administrator Tools
This section describes the user tools in the Administrator Tools menu under Facsimile Features.
❖ Program / Change / Delete Standard Message
Use this function to program standard messages to be printed at the top of the first
page of the original. It is useful for personalizing messages such as sending greetings.
You can program three standard messages. You cannot change the "Confidential", "Urgent", "Please phone.", or "Copy to corres. section" messages.
Use the same procedure to program and change your messages.
Program / Change:
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [Program / Change / Delete Standard Message].
D Check [Program / Change] is selected.
E
F
G
H
4
Program or change the message.
Select the message you want to program or change.
Enter a new message.
Press [OK].
Press the {User Tools/Counter} key.
Delete:
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [Program / Change / Delete Standard Message].
D Press [Delete], and then select the message you want to delete.
E
F
G
Press [Delete].
To delete another message, repeat from stepD.
To cancel a deletion, press [Do not Delete].
Press [Exit].
Press the {User Tools/Counter} key.
Downloaded from ManualsPrinter.com Manuals
107
Facsimile Features
❖ Store / Change / Delete Auto Document
You can program, change, or delete pages stored as auto documents.
For details about Store / Change Delete Auto Document, see "Storing, Changing, Deleting an Auto Document".
❖ Program / Change / Delete Scan Size
You can program, change, or cancel frequently used sizes.
For details about programming Scan Size, see "Program / Change / Delete
Scan Size".
4
❖ Print Journal
The Journal allows you to check a maximum of the last 50 communications
(receptions and transmissions) performed by the machine. You can also print
the Journal using the Information menu. See "Printing the Journal", Facsimile
Reference.
❖ Transmission Page Count
This function allows you to check the total number of pages transmitted and
received.
❖ Forwarding
This function allows you to have documents printed on the machine, and sent
to a specified End Receiver.
The default setting is Off.
For details about Forwarding, see "Forwarding".
❖ Memory Lock RX
When you switch Memory Lock on, received documents are stored in memory and not printed automatically. When a document is received in the Memory Lock mode, the Confidential File indicator blinks.
To print this document, enter the Memory Lock ID. A user without the ID cannot
print the document. This prevents unauthorized users from accessing the document.
To use Memory Lock, program the Memory Lock ID, and then switch Memory Lock on.
To store incoming documents from Special Senders only in Memory Lock,
program each sender with “Special Senders to Treat Differently".
This function is not available with Internet Fax.
The default setting is On.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [Memory Lock RX].
D Select [On] or [Off], and then press [OK].
E Press the {User Tools/Counter} key.
108
Downloaded from ManualsPrinter.com Manuals
Administrator Tools
❖ ECM (Error Correction Mode)
If part of a transmission fails because of a line problem, the lost data is automatically resent. For this function to work, the other machine must have
ECM. You can turn this function on or off through the following procedure.
This function is not available with Internet Fax.
If you turn ECM off, you cannot use the following functions:
• JBIG Transmission
• Super G3 Communication
The default setting is On.
❖ Parameter Setting
User Parameters allow you to customize various settings to suit your needs.
For details about Parameter Setting, see "Parameter Settings".
4
❖ Program Special Sender
By programming particular receivers as Special Sender in advance, you can
have Special Senders treated differently.
For details about how to program Special Sender, see "Special Senders to
Treat Differently".
❖ Box Setting
The following functions are for delivery and transfer of documents:
• Personal Box
• Information Box
• Transfer Box
For details about Box Setting, see "Box Settings".
❖ Transfer Report
For the Requesting Party to be able to receive Transfer Result Reports from
the Transfer Station, the Requesting Party must program the number of the
telephone line that is connected to their own machine.
Be sure to insert a pause after the area code.
For example, if you are in the United States and your fax number is 12121234567, program the following:
• 1212-1234567
You can program the fax number for the G3 line.
You cannot program or edit a Transfer Report when using a line (during communication). Program or edit after communication.
You cannot use Transfer Request if the telephone number of their machine is
not programmed into that machine.
Up to 16 digits are available for G3.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Transfer Report].
Downloaded from ManualsPrinter.com Manuals
109
Facsimile Features
4
E
Press [G3 Fax No. (Dir.)] to program a G3 fax number.
F
Enter your facsimile number using the number keys, and then press [OK].
G
If you make a mistake, press [Clear] or the {Clear/Stop} key, and then try again.
Press [Exit].
Press the {User Tools/Counter} key.
H
❖ Program Confidential ID
Program a Confidential ID to print a Confidential Reception.
If you do not program a Confidential ID, you cannot receive a Confidential
Transmission.
A Confidential ID can be any four-digit number, except 0000.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Program Confidential ID].
E Enter an ID using the number keys, and then press [OK].
F
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then try again.
Press the {User Tools/Counter} key.
110
Downloaded from ManualsPrinter.com Manuals
Administrator Tools
❖ Program Polling ID
Program a Polling ID to use the Transfer Request, Transfer Station, Default ID
Polling Transmission, and Default ID Polling Reception functions. When you
use ID Transmission, program the same ID as the one programmed on the
sender's machine.
Register a four-digit number using 0 through 9 and A through F (expect for
0000 and FFFF).
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Program Polling ID].
E Enter an ID using the number keys and [A] to [F], and then press [OK].
4
F
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then try again.
Press the {User Tools/Counter} key.
❖ Program Memory Lock ID
Program a Memory Lock ID to be entered before printing documents when
the Memory Lock function is activated.
A Memory Lock ID can be any four-digit number, except 0000.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Program Memory Lock ID].
E Enter an ID using the number keys, and then press [OK].
F
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then try again.
Press the {User Tools/Counter} key.
Downloaded from ManualsPrinter.com Manuals
111
Facsimile Features
4
❖ Select Dial / Push Phone
Use this function to select a line type when the machine is connected to a G3
analog line.
Dial and Push lines are available for selection.
The default setting is Push Button Phone.
If the optional extra G3 interface unit is installed, settings for the extra G3
lines appear.
This function is not available in some regions.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Select Dial / Push Phone].
E Press [Push Button Phone] or [Dial Phone (10PPS)] to select the line, and then
press [OK].
F Press the {User Tools/Counter} key.
❖ Reception File Setting
Selects whether received documents are saved on the hard disk to be printed
later or printed immediately without being saved.
The default setting is Print.
For details about Reception File Setting, see "Storing or Printing Received
Documents".
112
Downloaded from ManualsPrinter.com Manuals
Administrator Tools
❖ Stored RX File User Setting
The administrator can be specified for managing documents stored on the
machine after fax documents are received. To specify the administrator, enter
the administrator user code for managing documents using Web Image Monitor or DeskTopBinder.
You must register the administrator's User Code to the destination list in advance.
This function is only available when [Store] is selected in "Reception File Setting".
It is recommended that you use a Web Image Monitor operating under the
same network environment as this machine. Otherwise, the Web browser
may not open and an error may occur.
If the programmed user code was deleted using the Address Book Management function under System Settings, you cannot view received and saved
documents using a Web Image Monitor. Select [Off] in step D or reprogram
the user code.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext] twice.
D Press [Stored RX File User Setting].
E If you want to use a user code, press [On].
To disable user codes, press [Off], and then press [OK].
F Press the Destination key of the user you wish to specify, and then press
[OK].
G Check the selected user, and then press [OK].
H When a programmed user is deleted from the destination list, a message
“Destinations are invalid” is displayed. Re-enter the user.
I Press the {User Tools/Counter} key.
Downloaded from ManualsPrinter.com Manuals
4
113
Facsimile Features
4
❖ Folder Transfer Result Report
You can set whether the Folder Transfer Result Report is transmitted to the
specified e-mail address, when folders are programmed as the forwarding
destinations to which documents are sent from all senders or Special Senders.
You must first register the destination for the Folder Transfer Result Report
in the destination list. See "Registering a Fax Destination".
Specify a group destination to transfer documents to multiple destinations. A
maximum of 500 parties can be specified in a group. See "Registering Names
to a Group".
Even if the Folder Transfer Result Report is not successfully transmitted, the
report is not printed on this machine.
The default setting is Off.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext] twice.
D Press [Folder Transfer Result Report].
E To send the Folder Transfer Result Report, press [E-mail].
F
G
H
To not send the Folder Transfer Result Report, press [Do not E-mail], and
then press [OK]. Proceed to step G.
To cancel the selection, press [Cancel].
Press the Destination key of the e-mail address for notification, and then
press [OK].
Check the selected destination, and then press [OK].
Press the {User Tools/Counter} key.
Reference
p.3 “Accessing User Tools”
p.120 “Storing, Changing, and Deleting an Auto Document”
p.129 “Parameter Settings”
p.140 “Memory Lock”
p.164 “Storing or Printing Received Documents”
114
Downloaded from ManualsPrinter.com Manuals
Registering Fax Information
Registering Fax Information
This section describes Fax Information.
You can send information to the other party when transmitting or receiving a fax
document. This information is shown on the display of the other machine and
printed as a report. The following information can be sent.
Important
❒ You can confirm programmed settings from the User Parameter List. It is recommended that you print and keep the User Parameter List when you program or change settings. See “Parameter List”.
❖ Fax Header
The Fax Header is printed as the header of every fax you send. You should
include your name in the Fax Header.
You can program Fax Header1 or Fax Header2. When you send originals using the destination list, you can select which Fax Header is printed on the document received by the other party.
You can register “Fax Header” using up to 32 alphanumeric characters and
symbols.
You can use characters, symbols, numbers, and spaces.
You can set whether or not to print a Fax Header using [Fax Header Print] under
Options . See “Fax Header Print”, Facsimile Reference.
4
❖ Own Name
The Own Name is sent to the other party when you send or receive a fax . This
name should include your name. The Own Name is shown on the display of
the other machine and printed in a report.
Own Name can be used only if the other machine is of the same manufacturer
and has the Own Name function.
You can register “Own Name” using up to 20 alphanumeric characters and
symbols.
❖ Own Fax Number
The sender's Own Fax Number is sent to the other party when sending a fax.
The received facsimile number is shown on the display of the other machine
and printed in a report.
This function is available regardless of the manufacturer of the other party's
machine.
You can register “Own Fax Number” using up to 20 numbers, space, and
“+”symbol.
Reference
"Fax Header Print", Facsimile Reference
Downloaded from ManualsPrinter.com Manuals
115
Facsimile Features
Registering Fax Information
This section describes how to register Fax Information.
A Press [Facsimile Features].
B Press [Gen. Settings/ Adjust].
C Press [Program Fax Information].
4
D Select the Fax Information you want to register or change.
E Register the name and facsimile number.
F Press [Exit].
G Press the {User Tools/Counter} key.
116
Downloaded from ManualsPrinter.com Manuals
Registering Fax Information
Registering a Fax Header
This section describes how to register a Fax Header.
A Check that [Fax Header] is selected.
B Press [First Name] or [Second Name].
C Enter a fax header including your Own Name and Fax Number, and then
4
press [OK].
Registering an Own Name
This section describes how to register an Own Name
A Press [Own Name].
B Press [Own Name].
C Enter your own name and then press [OK].
Downloaded from ManualsPrinter.com Manuals
117
Facsimile Features
Registering an Own Fax Number
This section describes how to register an Own Fax Number.
A Press [Own Fax Number].
B Select line type to program.
4
The display differs depending on the optional units installed on the machine.
C Enter your own facsimile's number using the number keys, and then press
[OK].
To enter a + sign or a space, press [+] or [Space].
118
Downloaded from ManualsPrinter.com Manuals
Registering Fax Information
Changing Fax Information
This section describes how to change Fax Information.
A Press [Facsimile Features].
B Press [Gen. Settings/ Adjust].
C Press [Program Fax Information].
D Press [Fax Header], [Own Name], or [Own Fax Number] to change.
E Press the item you want to change.
To change a Fax Header, see "Registering a Fax Header".
To change Own Name, see "Registering an Own Name".
To change Own Fax Number, see "Registering an Own Fax Number".
4
F Press [OK].
G Press [Exit].
H Press the {User tools/Counter} key.
Reference
p.117 “Registering a Fax Header”
p.117 “Registering an Own Name”
p.118 “Registering an Own Fax Number”
Deleting Fax Information
This section describes how to delete Fax Information.
A Press [Facsimile Features].
B Press [Gen. Settings/ Adjust].
C Press [Program Fax Information].
D Press [Fax Header], [Own Name], or [Own Fax Number] to delete.
E Press the item you want to delete.
F Press [Backspace] or [Delete All], and then press [OK].
When deleting your own facsimile's number, press [Clear] or the {Clear/Stop}
key, and then press [OK].
G [Exit].
H Press the {User tools/Counter} key.
Downloaded from ManualsPrinter.com Manuals
119
Facsimile Features
Storing, Changing, and Deleting an Auto
Document
4
This section describes how to store, change, and delete an Auto Document.
If you often have to send a particular page to people (for example, a map, a
standard attachment, or a set of instructions), you can store that page in memory
as an Auto Document. This saves rescanning the original every time you want
to send it.
Use the following procedure to program a new Auto Document or overwrite an
existing one.
You can store the following items in an Auto Document:
• Originals (6 documents maximum, only one page per file)
• Scan settings (resolution, original type, and image density)
• Irregular scan area
• Document name (16 characters maximum)
Storing and Changing an Auto Document
This section describes how to store and change an Auto Document.
Important
❒ When about one hour passes after power to the machine is turned off, all fax
documents stored in memory are lost. If any documents have been lost for
this reason, a Power Failure Report is automatically printed when the operation switch is turned on. Use this report to identify lost documents.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [Store / Change / Delete Auto Document].
D Store a file, or change stored file.
To store a file, see "Storing a file".
To change stored file, see "Changing a file".
To change stored file's name, see "Changing only a file name".
E Press [Exit].
F Press the {User Tools/Counter} key.
Reference
p.121 “Storing a file”
p.121 “Changing a file”
p.122 “Changing only a file name”
120
Downloaded from ManualsPrinter.com Manuals
Storing, Changing, and Deleting an Auto Document
Storing a file
This section describes how to store a file.
A Check [Program / Change] is selected.
B Select [*Not Stored].
C Enter a file name, and then press [OK].
D Place the original, and then select any scan settings you require.
4
E Press the {Start} key.
The machine starts to scan and completes scanning.
To cancel scanning, press [fStop Scanning].
Changing a file
This section describes how to change the stored file.
A Check that [Program / Change] is selected.
B Select the file you want to change.
The “A file is already stored.If another file is stored, previousone will be deleted. Is it OK?” message is shown.
C Press [Store].
If you want to cancel storing, press [Do not Store].
D Place the original, and then select any scan settings you require.
Downloaded from ManualsPrinter.com Manuals
121
Facsimile Features
E Press the {Start} key.
The machine starts to scan and completes scanning.
To cancel scanning, press [fStop Scanning].
Changing only a file name
This section describes how to change the stored file's name.
A Press [Change Name].
B Select the file whose name you want to change.
C Enter a file name, and then press [OK].
4
Deleting an Auto Document
This section describes how to delete stored Auto Document.
You cannot delete an Auto Document waiting to be transmitted. Delete it after
the transmission or cancel the transmission, and then delete the Auto Document.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [Store / Change / Delete Auto Document].
D Press [Delete], and then select the file you want to delete.
E Press [Delete].
To cancel deleting, press [Do not Delete].
F Press [Exit].
G Press the {User Tools/Counter} key.
122
Downloaded from ManualsPrinter.com Manuals
Programming Changing and Deleting a Scan Size
Programming Changing and Deleting a
Scan Size
This section describes how to program, change, and delete a Scan Size.
When you select a scan size to scan a custom size original, two custom sizes are
available (Program Size 1 and Program Size 2). Use these functions to program
a custom size in advance.
To change an existing scan size, just use the same procedure.
Important
❒ When programming or changing a scan size, it is recommended that you
make a record of the new size.
4
You can program up to two sizes.
Specify a horizontal length from 128 to 1200 mm, or from 5.5 to 47 inches.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [Program / Change / Delete Scan Size].
D Select [Program Size 1] or [Program Size 2].
E Enter a horizontal size using the number keys.
Each time you press [mm] or [inch], the units switch between “mm" and
“inch". If you enter a length and press [mm] or [inch], the length is converted
automatically according to the unit (fractions are rounded off). For example,
when you enter {2}, {2}, and {0} in millimeters and change to “inch", the
length “8.7 inch" is shown on the display. If you press [mm] or [inch] again,
“221 mm" is displayed.
If you make a mistake, press [Clear] or the {Clear/Stop} key, and then try again.
To cancel a scan size, press [Cancel].
Downloaded from ManualsPrinter.com Manuals
123
Facsimile Features
F Select a vertical size, and then press [OK].
The displayed vertical size differs depending on the selected unit. When [mm]
is selected, [Auto Detect], [210 mm (A4)], [257 mm (B4 JIS)], [297 mm (A3)], [216 mm
(8 1/2)], and [279 mm (11)] are shown. When [inch] is selected, [Auto Detect], [8.3
inch (A4)], [10.1 inch (B4 JIS)], [11.7 inch (A3)], [8.5 inch], and [11.0 inch] are shown.
To cancel a scan size, press [Cancel].
4
G Press [Exit].
H Press the {User Tools/Counter} key.
Deleting a Scan Size
This section describes how to delete the programmed Scan Size.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [Program / Change / Delete Scan Size].
D Press [Delete], and then select [Program Size 1] or [Program Size 2].
E Press [Yes].
To cancel deleting, press [No]. The display returns to that of stepD.
F Press [Exit].
G Press the {User Tools/Counter} key.
124
Downloaded from ManualsPrinter.com Manuals
Forwarding
Forwarding
This section describes Forwarding settings.
This function allows you to have documents printed on the machine, and sent to
a specified End Receiver. This is useful if, for example, you are visiting another
office and would like a copy of your documents to be sent to that office.
You can also specify a “folder" as the forwarding destination.
Important
❒ To use this function, set Forwarding under Reception Settings to On (enable).
❒ You can select end receivers only from among destinations programmed in
the Address Book. You cannot specify programmed transfer stations as end
receivers.
❒ The Forwarding function does not forward documents received with Confidential Reception, Memory Lock, Polling Reception mode, or documents received by Transfer Request.
A fax number, e-mail address, IP-Fax destination, and folder can be set as the
forwarding destination.
Even when [On] is selected for “Forwarding" in “Reception Settings", if [Off] is
selected for the forwarding destination in this function, only printing is performed, not forwarding. See "Reception Settings".
When you wish to change the end receivers depending on the senders, specify
the end receivers by the senders, at “Program Special Sender". Documents not
received from specified senders are sent to the destination specified in this function.
You can specify whether or not to print forwarded documents. See "Parameter
Settings"(switch 11, bit 6).
Deleting a destination specified as a forward destination from the destination
list causes the settings of the forward destination to be deleted, so they must be
registered again. When a destination is changed, a document is transmitted to
the new destination. If there is no destination of the specified type, you can set
which destination to be used as an alternative destination. See "Parameter Settings" (switch 32, bit 0).
You can program one of the Quick Operation keys with operations for this function.
If you have specified a folder for forwarding, you can specify the file format
used for forwarding. See "Parameter Settings" (switch 21, bit 3).
4
Reference
p.95 “General Settings/Adjustment”
p.129 “Parameter Settings”
p.136 “Special Senders to Treat Differently”
p.99 “Reception Settings”
Downloaded from ManualsPrinter.com Manuals
125
Facsimile Features
Programming an End Receiver
This section describes how to program an End Receiver.
Important
❒ One end receiver can be registered for each special sender. To register two or
more end receivers, use group destination. However, a maximum of 500 destinations can be specified in a group.
4
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [Forwarding].
D Press [On].
If there is an End Receiver already programmed, a receiver name is shown. If
you want to change the receiver, press [Receiver] and proceed to stepE.
To cancel Forwarding, press [Off]and proceed to stepF.
E Specify an End Receiver using the destination list, and then press [OK].
The receiver name is shown to the right of [Receiver].
Press the key on the right of the display to switch the destination between fax
number, e-mail address, IP-Fax destination, and folder.
Set a folder destination in Address Book Management under Administrator
Tools in the System Settings menu. See “Registering Folders".
If you have specified a folder for forwarding, you can specify the file format
used for forwarding. See “Parameter Settings” (switch 21, bit 3).
If you make a mistake, press [Clear] before pressing [OK], and then try again.
F Press [OK].
126
Downloaded from ManualsPrinter.com Manuals
Forwarding
G Press the {User Tools/Counter} key.
Reference
p.129 “Parameter Settings”
p.221 “Registering Folders”
Quitting the Forwarding Function
This section describes how to quit the Forwarding function.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [Forwarding].
D Press [Off], and then press [OK].
4
E Press the {User Tools/Counter} key.
Downloaded from ManualsPrinter.com Manuals
127
Facsimile Features
Forwarding Mark
This section describes Forwarding Mark.
You can print a Forwarding Mark on receiver's documents that have been forwarded.
The receiver can distinguish between forwarded and normally received documents.
4
This function is not available when memory forwarding is performed to a folder
destination.
You can specify whether or not to print a Forwarding Mark in the User Parameters. See "Parameter Settings".
Reference
p.129 “Parameter Settings”
128
Downloaded from ManualsPrinter.com Manuals
Parameter Settings
Parameter Settings
This section describes Parameter Settings.
User Parameters allow you to customize various settings to suit your needs. To
change function settings, set the User Parameter Switches.
❖ Switches and Bits
Each User Parameter has a set of switches, and each of the switches consist of
eight bits, whose values are “0" or “1". The right most bit is bit 0 and the left
most is bit 7. You can adjust the settings to match your needs by switching the
value of bits between “0" and “1".
Switch 02:
0
0
1
1
1
0
1
1
↓
↓
↓
↓
↓
↓
↓
↓
7
6
5
4
3
2
1
0
4
❖ User Parameter List
User Parameter Switches are outlined in the following table.
Switch Bit
Item
0
1
02
0
Forwarding Mark
Off
On
02
3
TSI Print
Off
On
03
0
Automatic printing of the Communication
Result Report
Off
On
03
2
Automatic printing of the Memory Storage
Report
Off
On
03
3
Automatic printing of the Polling RX Reserve
Report
Off
On
03
4
Automatic printing of the Polling RX Result
Report
Off
On
03
5
Automatic printing of the Immediate TX Re- Off
sult Report
On
03
6
Automatic printing of the Polling TX Clear
Report
Off
On
03
7
Automatic printing of the Journal
Off
On
04
0
Automatic printing of the Confidential File
Report
Off
On
04
1
Automatic printing of Communication Failure Report and Transfer Result Report
Off
On
04
4
Indicates the parties
Off
On
04
5
Include sender's name on reports
Off
On
04
7
Include a portion of the image on reports
Off
On
Downloaded from ManualsPrinter.com Manuals
129
Facsimile Features
Switch Bit
Item
0
1
05
0
Receive Service Call (SC) Condition (Substitute Reception during service call)
Possible
(Substitute
RX)
Not possible (Reception off)
05
2,1
Substitute the reception when the machine
cannot print (because paper is jammed, all
paper trays have run out of paper, toner is
empty, or all paper trays are out of order)
00: Enabled
unconditionally
(Free)
-
01: Enabled
when Own
Name/Ow
n Fax
Number is
received
4
10: Enabled
for Closed
Network
Code match
11: Disabled (Reception off)
05
5
Print sheet is limited to that which has high- Off
est priority.
On
05
7
Empty tray alert (Paper Empty Warning)
even when one paper tray is empty
Off
On
06
6
First page scanned for book originals
From the
left page
From the
right page
07
2
Parallel Memory Transmission
Off
On
08
2
Authorized Reception Type
Receive
from specified senders only.
Receive all
documents
except from
specified
senders.
10
1
Combine two originals
Off
On
10
3
Page reduction when printing
Off
On
10
5
Reception file setting
Off
On
10
6
Use both e-mail notification and printed reports to confirm the transmission results
Off
On
11
6
Local print when forwarding
Off
On
11
7
Polling file after sending (Polling transmission standby time)
Delete
(Use Once)
Standby
(Save)
14
0
Print documents received with Auto Power- Immediate
On Reception (Night Printing mode)
printing
(On)
When turning on the
operation
switch (Off)
14
1
Long Document Transmission (Well Log)
On
130
Downloaded from ManualsPrinter.com Manuals
Off
Parameter Settings
Switch Bit
Item
0
1
14
2
Batch Transmission
Off
On
14
3
Reset when function changed
Off
On
17
2
Whether you need to press [Add] after speci- Not
fying a destination with the Destination key necessary
when broadcasting
Necessary
17
7
Receive documents by pressing the {Start}
key when originals are not set.
Off (no documents received after
pressing the
{Start} key)
On (documents received after
pressing the
{Start} key)
18
0
Print date with Fax Header
Off
On
18
1
Print transmitter origin with Fax Header
Off
On
18
2
Print file number with Fax Header
Off
On
18
3
Print page number with Fax Header
Off
On
19
0
Use paper delivery shift function
(Offset Print)
Off
On
19
1
Sort Journal by line type
Off
On
20
0
Automatic printing of the LAN-Fax Result
Report.
Off
On
Downloaded from ManualsPrinter.com Manuals
4
131
Facsimile Features
Switch Bit
Item
0
1
20
Reprinting time of stored documents in
memory that could not be printed using
LAN-Fax Driver
0000:
0 minutes
-
5,4,3,2
0001:
1 minutes
0010:
2 minutes
0011:
3 minutes
0100:
4 minutes
0101:
5 minutes
0110:
6 minutes
4
0111:
7 minutes
1000:
8 minutes
1001:
9 minutes
1010:
10 minutes
1011:
11 minutes
1100:
12 minutes
1101:
13 minutes
1110:
14 minutes
1111:
15 minutes
21
0
Print results of sending Reception Notice Re- Off
On
quest message
(print only
when an error occurs)
21
1
Respond to e-mail reception acknowledgment request
21
3
File format for files forwarded to folder des- TIFF
tinations
PDF
21
4
Transmit Journal by E-mail
Off
On
21
6
Display Network error
Display
(On)
Not display
(Off)
21
7
Transmit Error Mail Notification
On
Off
22
0
Detect a dial tone before sending faxes when
using the telephone line (LINE)
Not detect
(Off)
Detect
(On)
132
Downloaded from ManualsPrinter.com Manuals
Off
On
Parameter Settings
Switch Bit
Item
0
1
22
1
Detect a dial tone before sending faxes when
using the telephone line (LINE2)
Not detect
(Off)
Detect
(On)
22
2
Detect a dial tone before sending faxes when
using the telephone line (LINE3)
Not detect
(Off)
Detect
(On)
24
0
Store documents that could not be transmitted in memory
Off
On
24
1
Length of time documents that could not be
transmitted are stored in memory
24 hours
72 hours
25
4
RDS
Off
On
32
0
Select which order of priority to be used to
select an alternative destination when there
is no destination of the specified type.
Paper Out- Electronic
put Priority Output
Priority
<Priority
Order>
1. IP-Fax
destination
2. Fax
number
1. E-mail
address
2. Folder
3. E-mail
address
3. IP-Fax
destination
4. Folder
4. Fax
number
34
0
Use gatekeeper server with IP-Fax
Off
On
34
1
Use SIP server with IP-Fax
Off
On
Downloaded from ManualsPrinter.com Manuals
4
<Priority
Order>
133
Facsimile Features
Changing the User Parameters
This section describes how to set parameters.
Important
❒ Access to some User Parameter Settings may require options, or other settings
may need to be made beforehand.
❒ It is recommended that you print and keep a User Parameter list when you
program or change a User Parameter.
❒ Do not change any bit switches other than those shown on the previous pages.
4
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Parameter Setting].
E Select the switch number you want to change.
F Select the bit number you want to change.
When the bit number is pressed, the current value switches between 1 and 0.
Repeat from stepF to change another bit number for the same switch.
G Press [OK].
To cancel these settings, press [Cancel]. The display returns to that of stepE.
H Repeat step E through step G to change the switch settings.
I After all the settings are finished, press [Exit].
J Press the {User Tools/Counter} key.
134
Downloaded from ManualsPrinter.com Manuals
Parameter Settings
Printing the User Parameter List
This section describes how to print the User Parameter List.
Print this list to see the current User Parameter settings. However, only items of
importance or often-used items are included in the list.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Print List] next to [Parameter Setting].
E Press the {Start} key.
4
To cancel printing a list before pressing the {Start} key, press [Cancel] or the
{Clear/Stop} key.
To cancel printing a list after pressing the {Start} key, press [Stop Printing].
F Press the {User Tools/Counter} key.
Downloaded from ManualsPrinter.com Manuals
135
Facsimile Features
Special Senders to Treat Differently
4
This section describes Special Senders settings.
By programming particular senders in advance, you can set the following function for each sender:
• Authorized RX
• Forwarding
• Reception File Print Qty
• Print 2 Sided
• Memory Lock
• Paper Tray
Use the Own Name or Own Fax Number to program your senders. If the sender
has a machine of the same manufacturer, program an Own Name that has already been programmed as a sender. If the machine is not of the same manufacturer, use Own Fax Number.
You can apply the same settings to all programmed numbers. You can then customize the settings for individual numbers as necessary using the Special Sender
Registration function.
The following items can be programmed.
❖ Special Senders
Up to 30 Special Senders can be registered. A maximum of 20 characters can
be used for each name when using G3.
136
Downloaded from ManualsPrinter.com Manuals
Special Senders to Treat Differently
❖ Full/Partial agreement
When you program own names and facsimile names for multiple destinations, you can program a common sequence of characters to identify destinations using Partial agreement.
Using Full agreement :
Destination to be programmed
(Own Name)
Number of programmed identifications
NEW YORK BRANCH
3
HONG KONG BRANCH
SYDNEY BRANCH
Using Partial matching:
Destination to be programmed
(Own Name)
Number of programmed identifications
BRANCH
1
4
You can program up to 30 wild cards.
Spaces are ignored when identifications are compared.
You can use wild cards for the following functions:
• Forwarding
• Special Senders
• Authorized RX (Authorized Reception)
When using Partial agreement, you can enter up to the first 24 characters of
an e-mail address to use it as an own name or facsimile name.
Note
❒ You cannot program senders as Special Senders if they do not have Own
Name or Own Fax Number programmed.
❒ The machine cannot differentiate between Polling Reception and Free Polling
documents from Special Senders.
❒ You cannot use the following functions with Internet Fax receptions.
• Authorized RX
• Reception File Print Qty
• Memory Lock
❒ You can program up to 24 characters for the sender.
❒ You can check Own Name and Own Fax Number using the Journal. You can
check programmed Special Senders using the specified sender list.
❒ To use Forwarding, Print 2 Sided, or Paper Tray with Internet Fax reception,
program the sender's e-mail address.
❒ If you select "Off" for the Special Sender function in "Initial Set Up", the settings will be the same as the Reception Settings.
Downloaded from ManualsPrinter.com Manuals
137
Facsimile Features
Reference
p.99 “Reception Settings”
p.141 “Programming/Changing Special Senders”
p.142 “Authorized RX (Authorized Reception)”
p.143 “Forwarding”
Authorized Reception
4
Use this function to limit incoming senders.
The machine only receives faxes from programmed Special Senders, and therefore, it helps you screen out unwanted documents, such as junk mail, and saves
wasting fax paper.
Note
❒ To use this function, program the Special Senders function, and then select
“On" in “Authorized RX" with “Reception Settings". See "Reception Settings",
and Parameter Settings" (switch 08, bit 2).
❒ Without programming Special Senders, the Authorized RX function will not
work, even if you select “On".
❒ You can select to receive only from programmed senders or receive only from
senders other than those programmed in User Parameters. See "Parameter
Settings" (switch 08, bit 2).
❒ If you select “Off" for “Authorized RX" in “Initial Set Up", settings are the same
as the Reception Settings.
❒ You can change Special Senders in the same way as you program them.
Reference
p.99 “Reception Settings”
p.129 “Parameter Settings”
138
Downloaded from ManualsPrinter.com Manuals
Special Senders to Treat Differently
Forwarding
Print received documents, and then transfer them to those receivers programmed beforehand.
Folder destination can be registered.
It is also possible to forward faxes sent only by senders programmed as Special
Senders.
Note
❒ To use this function, program your Special Senders, and then select “On" for
“Forwarding" in “Reception Settings" See "Reception Settings".
❒ If you specify “On" in “Forwarding" and select [Same as Basic Settings], the fax
document is forwarded to the receivers programmed in “Specify End Receiver". See "Forwarding".
❒ If you do not program any Special Senders, the machine transfers all incoming documents to the other end receivers specified in “Specify End Receiver".
❒ You can set the fax destination, Internet fax destination, IP-Fax destination or
folder destination, as a forward destination.
❒ Set folder destinations using the Address Book Management function under
System Settings. See “Registering Folders".
❒ If you have specified a folder for forwarding, you can specify the file format
used for forwarding. See "Parameter Settings" (switch 21, bit 3).
4
Reference
p.125 “Forwarding”
p.129 “Parameter Settings”
p.221 “Registering Folders”
Reception File Print Quantity
Print the specified number of copies of documents received from programmed
senders (Special Senders).
If you do not program any Special Senders, the machine prints the specified
number of copies for all received documents.
Note
❒ You cannot use multi-copy printing with Polling Reception, Confidential Reception, or Memory Lock.
❒ you can specify up to 10 copies.
Downloaded from ManualsPrinter.com Manuals
139
Facsimile Features
Print 2 Sided
Print on both sides of the paper.
The optional duplex unit is required.
Note
❒ If you select the bypass tray for “Paper Tray", duplex printing is disabled.
Memory Lock
4
Use this function to store incoming documents from programmed senders (Special Senders) in memory without printing them. People without the Memory
Lock ID cannot print the documents, and therefore this function is useful for receiving confidential documents. If you do not program any senders, the machine
receives fax document from all senders using Memory Lock reception.
Important
❒ You must register Memory Lock ID in advance. See "Administrator Tools".
❒ If you program the same sender in Memory Lock and Forwarding, Forwarding is disabled.
Reference
p.107 “Administrator Tools”
Paper Tray
Print documents received from programmed senders (Special Senders) and the
documents from other senders on different types of paper.
For example, if blue paper is in Tray 1 and white paper is in Tray 2, the machine
prints the documents from Special Senders on the blue paper and prints the documents from other senders on the white paper, making it easy for you to separate the two.
If you do not program any Special Senders, the machine outputs documents received from all senders using the default paper tray.
Important
❒ For Polling Reception, you cannot select the paper tray.
Note
❒ If the machine receives a document that has a different size from the paper in
the specified tray, the machine prints it after splitting it or minimizing its size.
❒ Selection of the bypass tray enables you to specify the paper size in “Scan Area".
Reference
"Placing Originals", Facsimile Reference
140
Downloaded from ManualsPrinter.com Manuals
Special Senders to Treat Differently
Programming/Changing Special Senders
This section describes how to program and change Special Senders.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Program Special Sender].
E Check [Program / Change] is selected.
F Select the destination to program or change.
4
When programming a new Special Sender, press [*Not Programmed].
G Enter a destination name, and then press [OK].
Enter a destination name using Own Name or Own Fax Number.
H Press [Full Agreement] or [Partial Agreement].
I Select the item you want to program.
You must select only the item you want to program.
To cancel these settings, press [Cancel]. The display returns to that of stepF.
J Press [OK].
A Special Sender is programmed.
To program another sender, repeat the procedure from stepF.
K Press [Exit].
Downloaded from ManualsPrinter.com Manuals
141
Facsimile Features
L Press the {User Tools/Counter} key.
Reference
p.137 “Using Full agreement :”
p.142 “Authorized RX (Authorized Reception)”
p.143 “Forwarding”
p.144 “Reception File Print Qty”
p.145 “Print 2 Sided”
p.145 “Memory Lock”
p.145 “Paper Tray”
4
Authorized RX (Authorized Reception)
This section describes how to specify Authorized RX (Authorized Reception).
Specify when programming a Special Sender.
A Select [Authorized RX].
B Press [On] or [Off], and then press [OK].
Note
❒ After you perform step J on "Reception Settings", set "Authorized RX" of
"Reception Settings" to [On]. See "Reception Settings".
Reference
p.99 “Reception Settings”
142
Downloaded from ManualsPrinter.com Manuals
Special Senders to Treat Differently
Forwarding
This section describes how to specify Forwarding.
Specify when programming a Special Sender.
Important
❒ One forward destination can be registered for each Special Sender. To register
two or more forward destinations, use group destinations. However a maximum of 500 destinations can be specified in a group.
A Select [Forwarding].
B Select [On] or [Off].
4
If you select [Off], proceed to stepD.
Selecting [Same as Basic Settings] will result in the same setting made for "Forwarding" under "Administrator Tools". See "Administrator Tools".
C Press the Destination key of a forward destination, and then press [OK].
D Press [OK].
Note
❒ Press the key on the right of the display to switch the destination between
fax number, e-mail address, IP-Fax destination, and folder.
❒ Set folder destinations using the "Address Book Management" function
under "System Settings". See "Registering Folders".
❒ When a folder is specified as the forward destination, you can set a file format for forwarding. See "Parameter Settings" (switch 21, bit 3).
❒ Deleting a destination specified as a forward destination from the destination list causes the settings of the forward destination to be deleted, so they
must be registered again. When a destination is changed, a document is
transmitted to the new destination. If there is no destination of the specified type, you can set which destination to be used as an alternative destination. See "Parameter Settings" (switch 32, bit 0).
❒ After you perform stepK, set “Forwarding" of “Reception Settings" to
“On". See "Reception Settings".
Downloaded from ManualsPrinter.com Manuals
143
Facsimile Features
Reference
p.99 “Reception Settings”
p.107 “Administrator Tools”
p.129 “Parameter Settings”
p.221 “Registering Folders”
Reception File Print Qty
This section describes how to specify Reception File Print Qty.
Specify when programming a Special Sender.
4
A Select [Reception File Print Qty].
B Press [Number of Sets].
Selecting [Same as Basic Settings] will result in the same setting made for "RX
File Print Qty" of "Reception Settings". See "Reception Settings".
C Enter the print quantity using the number keys, and then press [OK].
Note
❒ If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then try again.
Reference
p.99 “Reception Settings”
144
Downloaded from ManualsPrinter.com Manuals
Special Senders to Treat Differently
Print 2 Sided
This section describes how to specify Print 2 Sided.
Specify when programming a Special Sender.
A Select [Print 2 Sided].
B Press [On] or [Off], and then press [OK].
Note
❒ Selecting [Same as Basic Settings] will result in the same setting made for "2
Sided Print" of "Reception Settings". See "Reception Settings".
Reference
p.99 “Reception Settings”
4
Memory Lock
This section describes how to specify Memory Lock.
Specify when programming a Special Sender.
A Select [Memory Lock].
B Press [On] or [Off], and then press [OK].
Note
❒ Selecting [Same as Basic Settings] will result in the same setting made for
“Program Memory Lock ID" under "Administrator Tools". See "Administrator Tools".
Reference
p.107 “Administrator Tools”
Paper Tray
This section describes how to specify Paper Tray.
Specify when programming a Special Sender.
A Select [Paper Tray].
B Select the tray you want to use, and then press [OK].
Note
❒ Selecting [Same as Basic Settings] will result in the same setting made for
“Paper Tray" of "Reception Settings". See "Reception Settings".
Reference
p.99 “Reception Settings”
Downloaded from ManualsPrinter.com Manuals
145
Facsimile Features
Programming Initial Set Up of a Special Sender
This section describes how to program Initial Set Up of a Special Sender.
Program the “Initial Set Up” of a Special Sender. You can also specify the Bypass
Tray Paper Size.
4
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Program Special Sender].
E Press [Initial Set Up].
F Select the function you want to program.
In this feature, “Authorized RX” has the same settings as “Reception Settings”.
See "Reception Settings".
G Press [Exit].
H Press the {User Tools/Counter} key.
Reference
p.99 “Reception Settings”
146
Downloaded from ManualsPrinter.com Manuals
Special Senders to Treat Differently
Programming Authorized RX and Special RX Function
A Select [Authorized RX] or [Special RX Function].
B Select [On] or [Off], and then press [OK].
The illustration shows the "Authorized RX" display as an example.
4
Programming Bypass Tray Paper Size
This section describes how to program Bypass tray Paper Size.
A Press [Bypass Tray Paper Size].
B Select the size you want to program.
You can select a size from [Auto Detect], [Standard Size], or [Custom Size].
If you select [Auto Detect], proceed to F.
If you select [Standard Size], proceed to C and F.
If you select [Custom Size], proceed to D to F.
If you select [Auto Detect], the machine recognizes the paper size automatically.
The machine will detect the paper size for the bypass tray as the short edge of
the paper is inserted into the machine. Even if you place an A4 size sheet in
theK orientation, the machine will detect it as A3L.
C Select the size you want to program from the sizes shown.
Downloaded from ManualsPrinter.com Manuals
147
Facsimile Features
D Enter the vertical size of the paper using the number keys, and then press
the {q} key.
Specify a vertical size from 210 mm (8.3") to 297 mm (11.6"). You cannot enter
a size smaller than 210 mm or larger than 297 mm.
Each time you press [mm] or [inch], the units switch between “mm” and
“inch”. If you enter a length and change the units by pressing [mm] or [inch],
it is converted automatically (fractions are rounded off).
4
E Enter the horizontal size of the paper using the number keys, and then
press the {q} key.
Specify a horizontal size from 148 mm (5.9") to 600 mm (23.7"). You cannot enter a size smaller than 148 mm or larger than 600 mm.
F Press [OK].
148
Downloaded from ManualsPrinter.com Manuals
Special Senders to Treat Differently
Deleting a Special Sender
This section describes how to delete a Special Sender.
Use this function to delete "Initial Set Up" of a Special Sender. The Bypass Tray
Paper Size can also be deleted.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Program Special Sender].
E Press [Delete], and then select the Special Sender you want to delete.
F Press [Delete].
4
To cancel deleting a special sender, press [Do not Delete]. The display returns
to that of stepE.
G Press [Exit].
H Press the {User Tools/Counter} key.
Printing the Special Sender List
This section describes how to print the Special Sender List.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Print List] next to [Program Special Sender].
E Press the {Start} key.
To cancel printing a list before pressing the {Start} key, press [Cancel] or the
{Clear/Stop} key.
To cancel printing a list after pressing the {Start} key, press [Stop Printing].
F Press the {User Tools/Counter} key.
Downloaded from ManualsPrinter.com Manuals
149
Facsimile Features
Box Settings
This section describes Box Settings.
The following functions are for delivery and transfer of documents:
• Personal Box
• Information Box
• Transfer Box
4
❖ SUB Code and SEP Code
SUB Code and SEP Code are IDs consisting of up to 20 digits, and can include
numbers, #, *, and spaces.
To use this function, you must program a box and SUB/SEP Code beforehand. The other party can send documents to, and retrieve stored documents
from, this box using the code.
Note
❒ The combined total of items that can be stored using the Personal Box, Information Box, and Transfer Box functions is 150.
❒ You cannot set the same Box code on two different boxes.
❒ Transmission or programming may not be allowed if there is not enough free
memory left. The amount of free memory left differs depending on the optional equipment installed.
Reference
p.151 “Programming/Changing Personal Boxes”
p.155 “Programming/Changing Information Boxes”
p.158 “Programming/Changing Transfer Boxes”
150
Downloaded from ManualsPrinter.com Manuals
Box Settings
Programming/Changing Personal Boxes
This section describes how to program and change Personal Boxes.
You can program the following items:
• Box name (required)
Up to 20 characters long
• SUB Code (required)
Up to 20 characters long and can be composed of digits 0-9, “#", “*", and spaces
(the first character cannot be a space).
• Password (optional)
Up to 20 characters long and can be composed of digits 0-9, “#", “*", and spaces
(the first character cannot be a space).
When programming a password, a mark is displayed before the Box name.
• Receiver (optional)
You can program one delivery destination for each Personal Box. Specify a
delivery destination programmed in Destination key.
4
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Box Setting].
E Check that [Program / Change] is selected.
F Select a box to program.
When programming a new box, press [*Not Programmed].
To change a box already programmed, press it and proceed to stepI.
G Press [Personal Box].
H Enter a box name, and then press [OK].
Downloaded from ManualsPrinter.com Manuals
151
Facsimile Features
I Enter a SUB Code.
To change the SUB Code, press [Clear] or the {Clear/Stop} key, and then try
again. To change a Box name, press [Box Name], and then repeat from step H.
J Specify the settings you require.
4
To program a password, see "Programming a password".
To program an End Receiver, see "Programming an End Receiver".
If you do not want to program a password or receiver, proceed to stepK.
K Press [OK].
L Press [Exit].
M Press the {User Tools/Counter} key.
Note
❒ you can specify a fax number, Internet Fax destination and IP-Fax destination as the transmission destination.
❒ The Fax Header is not printed on delivered documents.
❒ If a document cannot be delivered, a Communication Failure Report is
printed and the document is saved as a Confidential Reception document.
❒ You can edit boxes in the same way you program them. However, boxes
that are being used cannot be edited.
❒ If a destination in the destination table is deleted after being registered, delivery is not performed and the settings of the delivery destination are also
deleted. Also, when a delivery destination is changed, a document is sent
to the changed destination. If there is no destination of the specified type,
you can set which destination to be used as an alternative destination. See
"Parameter Settings" (switch 32, bit 0).
Reference
p.129 “Parameter Settings”
p.153 “Programming a password”
p.153 “Programming an End Receiver”
"Personal Boxes", Facsimile Reference
"Entering Text", About This Machine
152
Downloaded from ManualsPrinter.com Manuals
Box Settings
Programming a password
This section describes how to program a password for the Personal Box.
A Press [Password].
B Enter a password, and then press [OK].
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then try again.
4
C Re-enter the password, and then press [OK].
To change the password after pressing [OK], press [Change] and repeat stepsB
and C, or press [Cancel] and repeat from stepA.
D Press [OK].
Programming an End Receiver
This section describes how to program an End Receiver of the Personal Box.
A Press [Receiver].
B Select a destination using the destination list, and then press [OK].
Press the key shown on the right side of the screen to switch the destination
among fax number, Internet Fax address and IP-Fax address.
Downloaded from ManualsPrinter.com Manuals
153
Facsimile Features
Deleting Personal Boxes
This section describes how to delete Personal Boxes.
Important
❒ If there are documents in the box, you cannot delete the box.
4
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Box Setting].
E Press [Delete], and then select the box you want to delete.
F If the password is programmed, enter a password using the number keys,
and then press [OK].
If you make a mistake, press [Clear] or the {Clear/Stop} key, and then try again.
G Press [Delete].
To cancel deleting a box, press [Do not Delete].
H Press [Exit].
I Press the {User Tools/Counter} key.
154
Downloaded from ManualsPrinter.com Manuals
Box Settings
Programming/Changing Information Boxes
This section describes how to program and change Information Boxes.
You can store the following items:
• Box name (required)
Up to 20 characters long
• SEP Code (required)
Up to 20 characters long and can be composed of digits 0-9, “#", “*", and spaces
(the first character cannot be a space).
• Password (optional)
Up to 20 characters long and can be composed of digits 0-9, “#", “*", and spaces
(the first character cannot be a space).
When programming a password, a mark is displayed before the Box name.
4
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Box Setting].
E Check that [Program / Change] is selected.
F Select the box to program.
When programming a new box, press [*Not Programmed].
To change a box already programmed, press it, and then proceed to stepI. If a
password is programmed, enter the password, press [OK], and then proceed to
stepI.
G Press [Information Box].
H Enter a box name, and then press [OK].
Downloaded from ManualsPrinter.com Manuals
155
Facsimile Features
I Enter the SEP Code.
To change the SEP Code, press [Clear] or the {Clear/Stop} key, and then try
again. To change the box name, press [Box Name], and then repeat the procedure from stepH.
J Press [Password].
If you do not want to program a password, proceed to stepM.
4
K Enter a password, and then press [OK].
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then try again.
L Re-enter the password, and then press [OK].
To change the password after pressing [OK], press [Change] and repeat steps
K and L, or press [Cancel] and repeat from step J.
M Press [OK].
N Press [Exit].
O Press the {User Tools/Counter} key.
Note
❒ You can edit boxes in the same way you program them. However, boxes
that are being used cannot be edited.
❒ If a destination in the destination list is deleted after being registered, delivery is not performed and the settings of the delivery destination are also
deleted. Also, when a delivery destination is changed, a document is sent
to the changed destination. If there is no destination of the specified type,
you can set which destination to be used as an alternative destination. See
"Parameter Settings" (switch 32, bit 0).
Reference
p.129 “Parameter Settings”
"Information Boxes", Facsimile Reference
"Entering Text", About This Machine
156
Downloaded from ManualsPrinter.com Manuals
Box Settings
Deleting Information Boxes
This section describes how to delete Information Boxes.
Important
❒ If there are documents in the box, you cannot delete the box.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Box Setting].
E Press [Delete], and then select the box you want to delete.
4
F If the password is programmed, enter a password using the number keys,
and then press [OK].
If you make a mistake, press [Clear] or the {Clear/Stop} key, and then try again.
G Press [Delete].
To cancel deleting a box, press [Do not Delete]. The display returns to that of
stepE.
H Press [Exit].
I Press the {User Tools/Counter} key.
Downloaded from ManualsPrinter.com Manuals
157
Facsimile Features
Programming/Changing Transfer Boxes
This section describes how to program and change Transfer Boxes.
This function turns the machine into a fax relay station. Documents sent with a
SUB Code that matches the SUB Code programmed as a Transfer Box are received, and then relayed to a programmed receiver.
Since documents can be sent to multiple destinations in a single transfer request,
you can economize on call charges when sending to distant destinations.
4
Inform the Requesting Party of the SUB Code assigned to the Transfer Box.
When they want to have a document transferred by your machine, ask them to
send the document using SUB Code Transmission and specifying this SUB
Code. If a password has also been programmed, inform them of this too, and ask
them to enter it as the SID code.
You can store the following items:
• Box name (required)
Up to 20 characters
• SUB Code (required)
Up to 20 characters long and can be composed of digits 0-9, “#", “*", and spaces
(the first character cannot be a space).
• End Receiver (required)
You can store five End Receivers (destinations to which documents are forwarded) for each box. Specify End Receivers using a single or group destination programmed in the destination list beforehand.
• Password (optional)
Up to 20 characters long and can be composed of digits 0-9, “#", “*", and spaces
(the first character cannot be a space).
When programming a password, a mark is displayed in front of the Box
name.
158
Downloaded from ManualsPrinter.com Manuals
Box Settings
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Box Setting].
E Check that [Program / Change] is selected.
F Select the box to program.
When programming a new box, press [*Not Programmed].
4
To change a box already programmed, press it, and then proceed to stepI.
G Press [Transfer Box].
H Enter a Box name, and then press [OK].
I Enter a SUB Code.
To change the SUB Code, press [Clear] or the {Clear/Stop} key, and then try
again. To change Box name, press [Box Name], and then repeat from stepH.
J Specify the condition of registration.
To program End Receivers, see "Programming End Receivers".
To program a password, see "Programming a password".
K Press [OK].
L Press [Exit].
Downloaded from ManualsPrinter.com Manuals
159
Facsimile Features
M Press the {User Tools/Counter} key.
Note
❒ After documents are transferred, Transfer Result Reports are not sent back
to the sender.
4
❒ Specify the Internet fax destination and IP-Fax destination as a reception
station.
❒ After documents are transferred, they are deleted.
❒ When this function is set to on, the machine prints out the received documents it transfers and a Transfer Result Report after the transfer has finished. If you do not want it to print, contact your service representative.
❒ When the programmed receiver is a group destination for Multi-step
Transfer, Multi-step Transfer takes place. For more information, contact
your service representative.
❒ You can edit boxes in the same way you program them.
❒ If you delete a destination specified as a reception destination using the
destination list, the settings of the reception destination are also deleted, so
they must be registered again. When a destination is changed, a document
is transmitted to the new destination. If there is no destination of the specified type, you can set which destination to be used as an alternative destination. See "Parameter Settings" (switch 32, bit 0).
Reference
p.129 “Parameter Settings”
p.161 “Programming a password”
p.161 “Programming End Receivers”
"Entering Text", About This Machine
160
Downloaded from ManualsPrinter.com Manuals
Box Settings
Programming End Receivers
This section describes how to program End Receivers of Transfer Box.
A Select an End Receiver.
Press [Receiving Stn 1-5].
You can store five Receiving Station.
B Specify End Receivers with Destination keys, and then press [OK].
4
You can change the display to the fax destination, Internet fax destination,
and IP-Fax destination using the key on the left side of the display.
A reception station can also be registered as a group destination. In such a
case, a maximum of 500 parties including End Receiver 1-5 can be specified
in a group.
To register another End Receiver, repeat from stepA.
Programming a password
This section describes how to program a password for the Transfer Box.
A Press [Password].
B Enter a password, and then press [OK].
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then try again.
C Re-enter the password, and then press [OK].
To change the password after pressing [OK], press [Change] and repeat stepsB
and C, or press [Cancel] and repeat from stepA.
Downloaded from ManualsPrinter.com Manuals
161
Facsimile Features
Deleting Transfer Boxes
This section describes how to delete Transfer Boxes.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Box Setting].
E Press [Delete], and then select the box you want to delete.
4
F If the password is programmed, enter a password using the number keys,
and then press [OK].
If you make a mistake, press [Clear] or the {Clear/Stop} key, and then try again.
G Press [Delete].
To cancel deleting a special sender, press [Do not Delete].
H Press [Exit].
I Press the {User Tools/Counter} key.
162
Downloaded from ManualsPrinter.com Manuals
Box Settings
Printing the Box List
This section describes how to print the Box List.
Print a list showing the currently programmed Personal Boxes, Information Boxes, and Transfer Boxes.
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext].
D Press [Print List] next to [Box Setting].
E Press the {Start} key.
4
To cancel printing a list before pressing the {Start} key, press [Cancel] or the
{Clear/Stop} key.
To cancel printing a list after pressing the {Start} key, press [Stop Printing].
F Press the {User Tools/Counter} key.
Downloaded from ManualsPrinter.com Manuals
163
Facsimile Features
Storing or Printing Received Documents
4
This section describes how to store and print received documents.
Specify whether received documents are to be saved on the hard disk or printed
immediately without being saved. You can print stored documents repeatedly
or download them as images to a computer using a Web Image Monitor or DeskTopBinder. If you select printing without saving, documents are printed each
time they are received.
If using System Settings you have set the machine to distribute received faxes to
the delivery server, the documents cannot be saved on the hard disk.
You can use "Parameter Settings" (switch 10, bit 5) to set whether or not to print
stored received document. See "Parameter Settings".
If Store is selected and a destination for notification is specified, notification of
document reception can be sent to the specified e-mail address.
Documents saved on the hard disk are categorized as received and stored documents. For details about printing saved documents, see "Printing/Deleting Received and Stored Documents (Print/Delete Stored RX File)", Facsimile
Reference.
You cannot switch the setting if received documents have been stored on the
hard disk. To switch the setting, print documents stored on the hard disk if necessary, and then delete them.
Received confidential documents are stored in memory. Use the Print Confidential RX File function to print them.
With [Store] selected, more memory space is used as the number of saved documents increases. After memory space becomes insufficient, no more documents
are saved on the hard disk. When this happens, the machine starts printing then
overwriting old documents.
You can store received documents up to a total of approximately 320 pages or
2,240 (when the optional expansion memory is installed) of A4 size Standard
<ITU-T#1Chart>.
You cannot send received documents.
You cannot manage documents stored on the Document Server display.
It is recommended that you use a Web Image Monitor running under the same
network environment as this machine. Otherwise, the Web browser may not
open and an error may occur.
164
Downloaded from ManualsPrinter.com Manuals
Storing or Printing Received Documents
A Press [Facsimile Features].
B Press [Administrator Tools].
C Press [TNext]twice.
D Press [Reception File Setting].
E Select [Print] or [Store], and then press [OK].
4
To cancel your selection, press [Cancel].
When [Store] is selected, you can select whether or not to send notice of reception to a specific e-mail address. To notify of reception, press [Notify Dest.] and
select an e-mail address from the Internet Fax destinations programmed in
the address book. Further, you can register a group destination. In such a
case, a maximum of 500 parties can be specified in a group.
F Press the {User Tools/Counter} key.
Reference
"Printing/Deleting Received and Stored Documents (Print/Delete Stored
RX File)", Facsimile Reference.
Reception Report e-mail
When a received document is stored, this report is sent to the e-mail address set
as the destination for notification.
Downloaded from ManualsPrinter.com Manuals
165
Facsimile Features
4
166
Downloaded from ManualsPrinter.com Manuals
5. Printer Features
This chapter describes user tools in the Printer Features menu. For details on
how to access Printer Features, see "Accessing User Tools".
List / Test Print
This section describes the user tools in the Test Print menu under Printer Features.
❖ Multiple Lists
You can print the configuration page and error log.
❖ Config. Page
You can print the machine's current configuration values.
❖ Error Log
You can print error logs listing all errors that occurred during printing.
The most recent 30 errors are stored in the error log. If a new error is added
when there are 30 errors already stored, the oldest error is deleted. However,
if the oldest error belongs to one of the following types of print jobs, it is not
deleted. Instead, it will be stored separately in error logs for each job type, up
to a maximum of 30 for each log. You can check any of these print jobs for error log information.
• Sample Print
• Locked Print
• Hold Print
• Stored Print
The records of Auto Job Cancel and jobs canceled manually from the control
panel can be printed.
❖ Menu List
You can print a Menu List showing the machine's function menus.
❖ PCL Config. / Font Page
You can print the current configuration and installed PCL font list.
This menu can be selected only when the PCL option is installed.
❖ PS Config. / Font Page
You can print the current configuration and installed PostScript font list.
This menu can be selected only when the PostScript 3 option is installed.
❖ PDF Config. / Font Page
You can print the current configuration and installed PDF font list.
This menu can be selected only when the PostScript 3 option is installed.
❖ Hex Dump
You can print in the Hex Dump mode.
Downloaded from ManualsPrinter.com Manuals
167
Printer Features
Printing the Configuration Page
This section describes how to print the Configuration Page.
A Press [Printer Features].
B Press [Config. Page] on the [List / Test Print].
The configuration page is printed.
C Press the {User Tools/Counter} key.
5
Interpreting the Configuration Page
This section describes the Configuration Page.
❖ System Reference
• Unit Number
Displays the serial number assigned to the board by its manufacturer.
• Total Memory
Displays the total amount of memory (SDRAM) installed on the printer.
• Firmware Version
Printer: Displays the version number of the printer firmware.
System: Displays the version number of the system firmware.
Engine: Displays the version number of the printer engine.
LCDC: Displays the version number of the panel display.
NIB: Displays the version number of the Network interface.
• Device Connection
This item(s) appears when the device option(s) is installed.
• HDD: Font / Macro Download
Displays the capacity of the hard disk drive.
• Printer Language
Displays the version number of the printer driver language.
• Connection Equipment
Displays the installed optional equipments.
❖ Paper Input
Displays settings made under Tray Paper Settings menu.
❖ System
Displays settings made under the System menu.
168
Downloaded from ManualsPrinter.com Manuals
List / Test Print
❖ PCL Menu
Displays settings made under PCL Menu.
❖ PS Menu
Displays settings made under PS Menu.
❖ PDF Menu
Displays settings made under PDF Menu.
❖ Host Interface
Displays settings made under the Host Interface menu.
When DHCP is active on the network, the actual IP address, subnet mask and
gateway address appear in parentheses on the configuration page.
❖ Interface Information
Displays the interface information.
Reference
p.3 “Accessing User Tools”
Downloaded from ManualsPrinter.com Manuals
5
169
Printer Features
Maintenance
This section describes the user tools in the Maintenance menu under Printer Features.
Default settings are shown in bold type.
❖ List / Test Print Lock
You can lock the [List / Test Print] menu.
The default setting is Off.
❖ Delete All Temporary Print Jobs
You can delete all print jobs temporarily stored in the machine.
❖ Delete All Stored Print Jobs
You can delete all print jobs stored in the machine.
5
Reference
p.3 “Accessing User Tools”
p.41 “System Settings”
170
Downloaded from ManualsPrinter.com Manuals
System
System
This section describes the user tools in the System menu under Printer Features.
Default settings are shown in bold type.
❖ Print Error Report
Select this to have an error report printed when a printer or memory error occurs.
The default setting is Off.
❖ Auto Continue
You can select this to enable Auto Continue. When it is On, printing continues
after a system error occurs.
The default setting is Off.
❖ Memory Overflow
Select this to have a memory overflow error report printed.
The default setting is Do not Print.
5
❖ Job Separation
You can enable Job Separation.
The default setting is Off.
This menu can be selected only when a finisher (optional) is installed.
❖ Auto Delete Temporary Print Jobs
You can select to automatically delete print jobs temporarily stored in the machine.
The default setting is Off.
If you select [On], you can set up to 200 hours for auto file deleting.
❖ Auto Delete Stored Print Jobs
You can select to automatically delete print jobs stored in the machine.
The default setting is On, 3 day(s).
If you select [On], you can set up to 180 days for auto file deleting.
❖ Initial Print Job List
You can set the desired type of print job list that appears on the screen when
you press [Print Jobs].
• Complete List
Displays the list of print jobs stored in the machine.
• List Per User ID
Displays the list of the User ID who stored a file in the machine.
The default setting is Complete List.
Downloaded from ManualsPrinter.com Manuals
171
Printer Features
❖ Memory Usage
You can select the amount of memory used in Font Priority or Frame Priority,
according to paper size or resolution.
• Font Priority
This setting uses memory for registering fonts.
• Frame Priority
This setting uses frame memory for high speed printing.
The default setting is Frame Priority.
❖ Duplex
You can select to have print on both sides of each page.
The default setting is Off.
5
❖ Copies
You can specify the number of print sets. This setting is disabled if the
number of pages to print has been specified with the printer driver or another
command.
The number of copies can be specified from 1 to 999 by increments of one.
The default setting is 1.
❖ Blank Page Print
You can select whether or not to print blank pages.
The default setting is On.
The printer does not identify pages with white-coloured images as blank.
Pages that match one of the following conditions are identified as blank.
• There are no images.
• There are images but they are outside the printable area.
• There are only blank characters.
❖ Edge Smoothing
You can set to smoothen the edges of printed characters.
The default setting is On.
If you print either photo or halftone graphic images, select "Off".
❖ Toner Saving
You can save toner.
The default setting is Off.
❖ Printer Language
Specify the printer language.
The default setting is Auto.
This menu will appear under the following conditions:
• The PostScript 3 option is installed.
• Both the PostScript 3 and PCL options are installed.
❖ Sub Paper Size
You can enable the Auto Substitute Paper Size (A4, LT) feature.
The default setting is Off.
172
Downloaded from ManualsPrinter.com Manuals
System
❖ Page Size
You can select the default paper size.
• The paper size you can select is as follows:
A3, A4, A5, A6, B4JIS, B5JIS, 11×17, 81/2×14, 81/2×13, 81/2×11, 81/4×13,
8×13, 71/4×101/2, 51/2×81/2, Custom Size
The default setting is A4 (Metric version) / 81/2×11 (Inch version).
❖ Letterhead Setting
You can rotate original images when printing.
When printing, original images are always rotated by 180 degrees. Therefore,
output might not be as expected when printing onto letterhead or preprinted
paper requiring orientation. Using this function, you can specify image rotation.
The default setting is Off.
When set to "Off", original images are rotated by 180 degrees.
When set to Auto Detect, the machine detects a letterhead or preprinted paper automatically, and does not rotate the image.
When set to On (Always), the machine does not rotate the image.
This function reduces printing speed.
5
❖ Bypass Tray Setting Priority
Specify whether (Printer) Driver / Command or Machine Settings, has priority for determining the paper size for the bypass tray.
The default setting is Driver / Command.
❖ Edge to Edge Print
You can select whether or not to print on the entire sheet.
The default setting is Off.
The 5 mm margin along the edges may not be printed properly.
❖ Default Printer Language
You can set the default printer language if the machine cannot find the printer
language automatically.
This menu will appear under the following conditions:
• The PostScript 3 option is installed.
• Both the PostScript 3 and the PCL options are installed.
When the PostScript 3 option is installed, the default setting is PS.
When both the PostScript 3 and the PCL options are installed, the default setting is PCL.
❖ Tray Switching
You can set to switch the paper tray.
The default setting is Off.
Reference
p.3 “Accessing User Tools”
"Loading paper", Troubleshooting
Downloaded from ManualsPrinter.com Manuals
173
Printer Features
Host Interface
This section describes the user tools in the Host Interface menu under Printer
Features.
Default settings are shown in bold type.
❖ I/O Buffer
You can set the size of the I/O Buffer. Normally it is not necessary to change
this setting.
The default setting is 128KB.
❖ I/O Timeout
You can set how many seconds the machine should wait before ending a print
job. If data from another port usually arrives in the middle of a print job, you
should increase this timeout period.
The default setting is 15 seconds.
5
Reference
p.3 “Accessing User Tools”
174
Downloaded from ManualsPrinter.com Manuals
PCL Menu
PCL Menu
This section describes the user tools in the PCL Menu under Printer Features.
Default settings are shown in bold type.
This menu appears only when the PCL option is installed.
❖ Orientation
You can set the page orientation.
The default setting is Portrait.
❖ Form Lines
You can set the number of lines per page.
The number of lines can be specified from 5 to 128 by increments of one.
The default setting is 64 (Metric version) / 60 (Inch version).
❖ Font Source
You can set the storage location of the default font.
The default setting is Resident.
RAM, HDD and SD can be selected only when fonts have been downloaded
to the machine.
5
❖ Font Number
You can set the ID of the default font you want to use.
The number of font numbers can be specified from 0 to 63 by increments of
one.
The default setting is 0.
❖ Point Size
You can set the point size you want to use for the selected font.
The number of point sizes can be specified from 4.00 to 999.75 by increments
of 0.25.
The default setting is 12.00.
This setting is effective only with variable-space fonts.
❖ Font Pitch
You can set the number of characters per inch for the selected font.
The number of characters per inch can be specified from 0.44 to 99.99 by increments of 0.01.
The default setting is 10.00 pitches.
This setting is effective only with fixed-space fonts.
❖ Symbol Set
Specify the character set of the selected font. The available options are as follows:
Roman-8, ISO L1, ISO L2, ISO L5, PC-8, PC-8 D/N, PC-850, PC-852, PC8-TK,
Win L1, Win L2, Win L5, Desktop, PS Text, VN Intl, VN US, MS Publ, Math-8,
PS Math, VN Math, Pifont, Legal, ISO 4, ISO 6, ISO 11, ISO 15, ISO 17, ISO 21,
ISO 60, ISO 69, Win 3.0
The default setting is PC-8.
Downloaded from ManualsPrinter.com Manuals
175
Printer Features
❖ Courier Font
You can select a courier font type.
The default setting is Regular.
❖ Extend A4 Width
You can extend the printing area width (when printing on A4 size paper with
PCL).
The default setting is Off.
When the setting is "On", the width will be 81/2 inches.
❖ Append CR to LF
When set to On, a carriage return will follow each line feed: CR=CR, LF=CR−LF,
FF=CR−FF.
The default setting is Off.
5
❖ Resolution
You can set the print resolution in dots per inch.
The default setting is 600 dpi.
Reference
p.3 “Accessing User Tools”
176
Downloaded from ManualsPrinter.com Manuals
PS Menu
PS Menu
This section describes the user tools in the PS Menu under Printer Features.
Default settings are shown in bold type.
This menu appears only when the PostScript 3 option is installed.
❖ Data Format
You can select a data format.
The default setting is TBCP.
This setting is not effective when operating the machine with a parallel or
EtherTalk connection.
When operating the machine with a parallel connection, and also if the binary
data is sent from the printer driver, the print job is canceled.
When operating the machine with an Ethernet connection, the print job is canceled under the following conditions:
• The printer driver data format is TBCP, and the data format selected on the
display panel is Binary Data.
• The printer driver data format is binary, and the data format selected on
the display panel is TBCP.
5
❖ Resolution
You can set the print resolution in dots per inch.
The default setting is 600 dpi.
Reference
p.3 “Accessing User Tools”
Downloaded from ManualsPrinter.com Manuals
177
Printer Features
PDF Menu
This section describes the user tools in the PDF Menu under Printer Features.
Default settings are shown in bold type.
This menu appears only when the PostScript 3 option is installed.
❖ Change PDF Password
Set the password for the PDF file executing PDF Direct Print.
• Current Password
• New Password
• Confirm New Password
A password can be set using the Web Image Monitor, but in this case the password information is sent through the network. If security is a priority, set the
password using this menu from the Control Panel.
5
❖ PDF Group Password
Set the group password already specified with DeskTopBinder.
• Current Password
• New Password
• Confirm New Password
A password can be set using the Web Image Monitor, but in this case the password information is sent through the network. If security is a priority, set the
password using this menu from the Control Panel.
❖ Resolution
You can set the print resolution in dots per inch.
The default setting is 600 dpi.
Reference
p.3 “Accessing User Tools”
178
Downloaded from ManualsPrinter.com Manuals
6. Scanner Features
This chapter describes user tools in the Scanner Features menu. For details on
how to access Scanner Features, see "Accessing User Tools".
Scan Settings
This section describes the user tools in the Scan Settings menu under Scanner
Features.
Default settings are shown in bold type.
❖ Default Scan Settings
Various basic settings (scan type, resolution, image density, and scan size) can
be set. You can register the scan settings in the same way as specifying them.
The default setting for "Scan Type" is Text (Print).
The default setting for "Resolution" is 200 dpi.
The default setting for "Image Density" is Auto Image Density (Medium).
The default setting for "Scan Size" is Auto Detect.
❖ Wait Time for Next Orig.: Exposure Glass
To divide originals and scanning them individually with the exposure glass to form
a single file, select [Off], [Set Wait Time], or [Continuous Wait] for the waiting status.
The default setting is Set Wait Time.
The default setting time is 60 sec..
If you select [SADF] in [Original Feed Type] on the Scan to Folder screen, the [Wait
Time for Next Orig.: Exposure Glass] setting becomes invalid.
If you select [Batch] in [Original Feed Type] on the Scan to Folder screen, the
[Wait Time for Next Orig.: Exposure Glass] setting becomes invalid, and the machine waits for an additional original to be placed.
If [Set Wait Time] is selected, enter the wait time in seconds (3-999) for placing
additional originals with the number keys. Scanning will start if additional
originals are placed and the {Start} key is pressed within this time. You can
end scanning and begin transmission by pressing the {q} key within this
time. Once the specified time has elapsed, transmission starts automatically.
If [Continuous Wait] is selected, the machine will wait for additional originals
until the {q} key is pressed. Scanning will start when additional originals
are placed and the {Start} key is pressed. You can end scanning and begin
sending by pressing the {q} key.
If originals are placed in the ADF (automatic document feeder), transmission
will start without waiting for additional originals after all originals in the
ADF have been scanned, regardless of the specified settings.
If a paper misfeed occurs or any of the following operations are performed
while the machine is waiting for additional originals, the countdown stops
and does not start again until the {q} key is pressed.
• Changing the settings such as the scan settings
• Opening the upper cover of the ADF
• from
Pressing
the {Interrupt}
key to activate the copy mode
179
Downloaded
ManualsPrinter.com
Manuals
Scanner Features
6
❖ Wait Time for Next Original(s): SADF
When dividing originals and scanning them separately with the ADF to form
a single file, select [Set Wait Time] or [Continuous Wait] for the waiting status.
The default setting is Set Wait Time.
The default setting time is 60 sec..
This setting is valid if [SADF] is specified for [Original Feed Type] when scanning.
If [Set Wait Time] is selected, enter the wait time in seconds (3-999) for placing
additional originals with the number keys. Scanning will start automatically
if additional originals are placed within this time. You can end scanning and
begin transmission by pressing the {q} key within this time. Once the specified time has elapsed, transmission starts automatically.
If [Continuous Wait] is selected, the machine will wait for the additional originals until the {q} key is pressed. Scanning will start when additional originals are placed and the {Start} key is pressed. You can end scanning and begin
sending by pressing the {q} key.
Even if originals are placed on the exposure glass, the machine will operate
according to the specified settings. However, every time originals are placed
on the exposure glass, you must press the {Start} key to start scanning.
If a paper misfeed occurs or any of the following operations are performed
while the machine is waiting for additional originals, the countdown stops
and does not start again until the {q} key is pressed.
• Changing the settings such as the scan settings
• Opening the upper cover of the ADF
• Pressing the {Interrupt} key to activate the copy mode
❖ Original Setting
Set the default for whether originals are one-sided or two-sided and if twosided, the relationship between those sides. When the originals are always the
same, set this for the default to make operation easier. You can select [1 Sided
Original], [2 Sided Orig.: T to T] (Top to Top), or [2 Sided Orig.: T to B] (Top to Bottom).
The default setting is 1 Sided Original.
❖ Switch to Batch
Select [SADF] or [Batch] as the scanning mode that appears as [Original Feed
Type] in the initial display of the scanner mode.
The default setting is SADF.
❖ Mixed Original Sizes Priority
This setting determines whether the original size is to be automatically detected when originals of different sizes are inserted in the ADF. You can select
[On] or [Off].
The default setting is Off.
If the original size is specified when scanning, this setting is ignored.
When [Off] is selected and [Auto Detect] is selected for scan size, if originals of
different sizes are placed in the ADF, the maximum size will be detected as
the scan size.
180
Downloaded from ManualsPrinter.com Manuals
Scan Settings
❖ Original Orientation Priority
Select the default for original placement orientation. When originals are always positioned the same way, select that orientation as the default to make
operation easier.
The default setting is Top to top original.
❖ Change Initial Mode
Select [Standard] to use the standard settings as the initial mode which is the
mode of the machine immediately after the operation switch is turned on or
modes are cleared or reset.
Select [Program No.10] to use the settings stored in Program No.10 as the initial
mode.
The default setting is Standard.
Reference
p.3 “Accessing User Tools”
6
Downloaded from ManualsPrinter.com Manuals
181
Scanner Features
Destination List Settings
This section describes the user tools in the Destination List Settings menu under
Scanner Features.
Default settings are shown in bold type.
❖ Destination List Display Priority 1
Select a destination list to be displayed when the machine is in the initial state.
You can select either [E-mail / Folder] or [Delivery Server].
The default setting is Delivery Server.
❖ Destination List Display Priority 2
In the machine’s address book, select which address book appears by default.
You can select either [E-mail Address] or [Folder].
The default setting is E-mail Address.
6
❖ Select Title
Select the titles for destinations and group destinations of e-mail and Scan to
Folder. Selected titles appear in the e-mail and Scan to Folder destination list
to be used for searching for destinations. Select [Title 1] (ten titles), [Title 2] (ten
titles), or [Title 3] (five titles).
The default setting is Title 1.
❖ Update Delivery Server Destination List
To update the delivery server destination list, press [Update Delivery Server Destination List].
Normally, the delivery server destination list is automatically updated. This
function allows manual updating at any time.
Reference
p.3 “Accessing User Tools”
"Batch, SADF", Scanner Reference
"Items for Specifying Scan Settings", Scanner Reference
"Setting Items for Original Feed Type", Scanner Reference
"Scanning Multiple Pages of Originals as One File", Scanner Reference
182
Downloaded from ManualsPrinter.com Manuals
Send Settings
Send Settings
This section describes the user tools in the Send Settings menu under Scanner
Features.
Default settings are shown in bold type.
❖ TWAIN Standby Time
When the machine is being used to send e-mail or a file, or functioning as Document Server or a network delivery scanner, a scanning request to the machine
as a TWAIN scanner will switch the machine to the network TWAIN scanner
function. This setting determines the delay until the machine switches to the
network TWAIN scanner function.
When [Off] is selected, the machine will switch to the network TWAIN scanner function at once.
When [On] is selected, you can enter the delay time with the number keys (330 seconds). The machine will switch to the network TWAIN scanner function when the time set here passes after the last key operation.
The default setting is On, 10 sec..
❖ File Type Priority
Select whether to send the scanned originals as single-page files or a multiplepage file.
For single-page files, select either TIFF/JPEG or PDF. For multi-page files, select either TIFF or PDF.
The default setting is Multi-page: TIFF.
You cannot select multi-page TIFF format for an image stored in JPEG format.
6
❖ Compression (Black & White)
Select whether or not to compress black and white scan files.
The default setting is On.
The actual time required for file transfer will vary depending on the file size
and network load.
Compression reduces the time required for transferring the scan file.
❖ Compression (Gray Scale)
Specify whether or not to compress multi-level (grayscale) scan files.
The default setting is On.
If you select [On], you can specify the compression level between one and five.
The image quality is better for lower compression, but the time required for
file transfer increases accordingly.
The actual time required for file transfer will vary depending on the file size
and network load.
Downloaded from ManualsPrinter.com Manuals
183
Scanner Features
❖ Print & Delete Scanner Journal
Up to 100 transmission/delivery results can be checked on this machine. If
the stored transmission/ delivery results reach 100, select whether to print
the delivery journal.
The default setting is Print and Delete All.
• Print and Delete All
The transmission/delivery journal is printed automatically. The printed
journal is deleted.
• Do not Print: Delete Oldest
Transmission/delivery results are deleted one by one as new results are
stored.
• Do not Print: Disable Send
Transmission/delivery cannot be performed when the journal is full.
When printed, all records are deleted after printing. When not printed,
records over the limit are automatically deleted in succession from the oldest
record.
While the journal is being printed, files with the status waiting cannot be sent.
6
❖ Print Scanner Journal
The scanner journal is printed and deleted.
❖ Delete Scanner Journal
The scanner journal is deleted without being printed.
❖ Max. E-mail Size
Select whether or not to limit the size of an e-mail to which an image is attached.
The default setting is On.
The default size limit is 2048 KB.
When [On] is selected, enter the size limit (128-102400 KB) with the number
keys.
When the SMTP limits the size, match that setting.
❖ Divide & Send E-mail
This function is effective only when [On] is selected for [Max. E-mail Size].
The default setting is Yes (per Max. Size).
Select whether or not an image exceeding the size specified in [Max. E-mail Size]
should be divided and sent using more than one e-mail.
When [Yes (per Max. Size)] is selected, enter the Max. Number of Divisions (2500) with the number keys.
When [Yes (per Max. Size)] is selected, some received files may not be able to be
restored, depending on the type of e-mail software.
When [Multi-page: TIFF] or [Multi-page: PDF] is selected, the image will not be divided.
When [No] is selected, the e-mail is not sent if its size exceeds the limit, and an
error message appears. The scan file is discarded.
Set the maximum e-mail size within the capacity of the SMTP server.
184
Downloaded from ManualsPrinter.com Manuals
Send Settings
❖ E-mail Information Language
Select the language in which e-mail information such as title, document
name, and sender's name is sent.
Select one of the following 20 languages:
British English, American English, German, French, Italian, Spanish, Dutch,
Portuguese, Polish, Czech, Swedish, Finnish, Hungarian, Norwegian, Danish, Japanese, Simplified Chinese, Traditional Chinese, Russian, and Hangul.
The e-mail text which is a template cannot be changed.
The default setting is British English.
❖ Store File Priority
Select [Send & Store], [Store Only], or [Off] as the default that is displayed when
modes are cleared or reset, or immediately after the operation switch is
turned on.
The default setting is Off.
If you select [Send & Store], "Send & Store" appears in [Scanner Features], and
files are stored and sent simultaneously.
If you select [Store Only], "Store Only" appears in [Scanner Features], and files
are only stored.
If you select [Off], [Scanner Features] shows that nothing has been selected. If
you want to store files, specify [Store File] for scanning.
6
❖ Stored File E-mail Method
Specify the e-mail setting for sending stored files. You can select [Send File] or
[Send URL Link]. This setting can be used for the following:
The default setting is Send File.
• Sending Stored Files by E-mail
• Simultaneous Storage and Sending by E-mail
If you select [Send File], actual files are attached to e-mails.
If you select [Send URL Link], URL Links to file locations are attached to e-mails.
Reference
p.3 “Accessing User Tools”
Downloaded from ManualsPrinter.com Manuals
185
Scanner Features
6
186
Downloaded from ManualsPrinter.com Manuals
7. Registering Addresses and Users
for Facsimile/Scanner Functions
This chapter describes how to register destinations and users in the Address
Book. For details on how to access System Settings see "Accessing User Tools".
Address Book
This section describes Address Book settings.
Registering information such as the names of users and their e-mail addresses in
the Address Book allows you to manage them easily.
Important
❒ Address Book data is stored on the hard disk. It can be lost if there is some
kind of hard disk failure. The manufacturer shall not be responsible for any
damages resulting data loss.
You can register and manage the following items in the Address Book:
❖ Names
You can register the name of the user and the key display. This is the basic information required for managing user of the machine.
To register a fax number or e-mail address in the address book, you must register information such as the user name and destination name in advance.
❖ Auth. Info
You can register user codes in order to restrict particular functions to certain
users, and to check their use of each function. You can also register login user
names and login passwords to be used when sending e-mail, sending to folders, or accessing an LDAP server.
Downloaded from ManualsPrinter.com Manuals
187
Registering Addresses and Users for Facsimile/Scanner Functions
❖ Protection
You can set protection codes to stop sender's name from being used or folders
from being accessed without authorization.
❖ Fax Dest.
You can register fax numbers, line, fax header and select label insertion.
When using IP-Fax, you can register the IP-Fax destination and select the protocol.
• Fax Destination
• IP-Fax Destination
7
❖ E-mail Address
You can register e-mail destinations in the Address Book.
188
Downloaded from ManualsPrinter.com Manuals
Address Book
❖ Folder
You can register the protocol, path name and server name.
• SMB
• FTP
• NCP
7
❖ Add to Group
You can put registered e-mail and folder destinations into a group for easier
management.
Note
❒ You can also use a Web Image Monitor to register names in the Address Book.
With the SmartDeviceMonitor for Admin, you can register multiple names at
the same time. For details about using Web Image Monitor, see the Web Image Monitor Help.
❒ Using Address Management Tool in SmartDeviceMonitor for Admin, you
can backup Address Book data. We recommend backing up data when using
the Address Book. For operating instructions, see SmartDeviceMonitor for
Admin Help.
Downloaded from ManualsPrinter.com Manuals
189
Registering Addresses and Users for Facsimile/Scanner Functions
Managing names in the Address Book
By registering a name and key display beforehand, you can specify e-mail and
folder destinations simply by selecting the name key.
Reference
p.192 “Registering Names”
Sending fax by Quick Dial
Register a fax number in the Address Book so you can specify it only by selecting
the fax destination, shown on the fax initial display when sending a fax. When
label insertion is set to “On", the receiver's name and standard messages are
printed on the fax message when it is received at the other end.
By registering IP-Fax destinations in the Address Book, you can specify a destination simply by selecting it from the destinations that appear in the initial fax
display. Registered IP-Fax numbers can be used and printed as sender’s IP-Fax
numbers.
Reference
p.204 “Fax Destination”
7
Sending e-mail by Quick Dial
By registering e-mail addresses in the Address Book, you can specify e-mail destinations simply by selecting them from the fax initial display when sending a
document by Internet fax.
You can also specify an e-mail address by selecting the destination shown on the
initial scanner display when sending a document using the scanner function. A
registered e-mail address can be used as the sender's address, and the sender's
addresses are automatically entered in the “From" field of an e-mail header.
Reference
p.217 “E-mail Destination”
190
Downloaded from ManualsPrinter.com Manuals
Address Book
Sending scanned files to a shared folder directly
After registering the path name, user name and password, you can connect to a
shared folder simply by selecting the destination shown on the initial scanner
display whenever sending files using the scanner function to a shared folder.
To share the folder using Windows, select the SMB protocol.
To register the folder to the FTP server, select the FTP protocol.
To register the folder to the NetWare server, select the NCP protocol.
Reference
p.221 “Registering Folders”
Preventing unauthorized user access to shared folders from the
machine
After registering a protection code, you can specify the object of protection to
prevent an e-mail destination from being used without permission.
You can prevent unauthorized access to registered folders.
Reference
p.247 “Registering a Protection Code”
7
Managing users and machine usage
Register user codes to limit users to the following functions and check their use
of each function:
• Copier
• Document Server
• Facsimile
• Scanner
• Printer
Reference
p.196 “Authentication Information”
Downloaded from ManualsPrinter.com Manuals
191
Registering Addresses and Users for Facsimile/Scanner Functions
Registering Names
This section describes names in Address Book.
Register user information including their names.
The user name is useful for selecting a destination when sending faxes or e-mail.
You can also use it as a folder destination.
You can register up to 2000 names.
Registering Names
This section describes how to register names.
A Press [System Settings].
7
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Press [New Program].
G Press [Change] on the right of the Name.
The name entry display appears.
H Enter the name, and then press [OK].
The key display name is set automatically.
I When you want to change the key display, press [Change] under "Key Display".
J Enter the key display, and then press [OK].
192
Downloaded from ManualsPrinter.com Manuals
Registering Names
K Press the key for the classification you want to use under "Select Title.
The keys you can select are as follows:
• [Freq.]: Added to the page that is displayed first.
• [AB], [CD], [EF], [GH], [IJK], [LMN], [OPQ], [RST], [UVW], [XYZ], [1] to [10]: Added to the list of items in the selected title.
You can select [Freq.] and one more page for each title.
To continue registering the name, press [Continue to Program], and then repeat
the procedure from step G.
L Press [OK].
M Press [Exit].
N Press the {User Tools/Counter} key.
Note
❒ The name can be used for documents in the Document Server. For details
about the Document Server, see "Using the Document Server", Copy/ Document Server Reference.
7
❒ You can register up to 2000 programs and allocate them registration numbers between 00001 and 50000.
❒ Registration numbers are initially assigned automatically, but you can
change them afterward. To change a registration number, press [Change] to
the right of “Registration No.”, and enter a new number using the number
keys.
Reference
"Entering Text", About This Machine
"Using the Document Server", Copy/ Document Server Reference
Downloaded from ManualsPrinter.com Manuals
193
Registering Addresses and Users for Facsimile/Scanner Functions
Changing a Registered Name
This section describes how to change a registered name.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the registered name you want to change.
7
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G To change the name or key display, press [Change] on the right of the name
or key display.
H Enter the name or key display, and then press [OK].
I To change the title, press the key for the classification you want to use from
Select Title.
J To change the registration number, press [Change] to the right of Registration No..
K Enter a new registration number using the number keys, and then press the
{q} key.
Reference
"Entering Text", About This Machine
194
Downloaded from ManualsPrinter.com Manuals
Registering Names
Deleting a Registered Name
This section describes how to delete a registered name.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Press [Delete].
F Select the name you want to delete.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
7
G Press [Yes].
H Press [Exit].
I Press the {User Tools/Counter} key.
Downloaded from ManualsPrinter.com Manuals
195
Registering Addresses and Users for Facsimile/Scanner Functions
Authentication Information
This section describes the procedure for authenticating a user code.
Important
❒ The functions associated with each user code are the same. If you change or
delete user codes, management data and limits associated with that code become invalid.
Register user codes to limit users to the following functions and check their use
of each function:
Copier
Document Server
Facsimile
Scanner
Printer
Note
❒ You can register up to 100 user codes. If you add the optional user account
enhance unit, you can register up to 500 user codes.
7
❒ The number of copies made of documents stored in the Document Server using the facsimile function is counted for each user code. This allows you to
check each user's usage.
❒ The number of copies scanned using the scanner function is counted for each
user code. This allows you to check each user's usage.
❒ To automatically register the printer driver user code, select [Printer: PC Control] for the printer in User Code Authentication. To use the user code set in
User Tools, set the user codes registered in User Tools for the printer driver.
❒ For details about setting user codes for the printer driver, see Printer Driver
Help.
Reference
p.62 “User Authentication Management”
196
Downloaded from ManualsPrinter.com Manuals
Authentication Information
Registering a User Code
This section describes how to register a user code.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Press the name whose code is to be registered, or enter the registered
number using the number key.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Auth. Info].
H Enter the user code using the number keys, and then press the {q} key.
7
If you make a mistake, press [Clear] or the {Clear/Stop} key.
I Press [TNext] twice.
J Select the functions to be used with the user code from Available Functions.
K Press [OK].
To continue registering user codes, repeat the procedure from step F.
L Press [Exit].
Downloaded from ManualsPrinter.com Manuals
197
Registering Addresses and Users for Facsimile/Scanner Functions
M Press the {User Tools/Counter} key.
Note
❒ You can enter a one-to eight-digit user code.
❒ To register the name, see “Registering Names”.
Reference
p.192 “Registering Names”
Changing a User Code
This section describes how to change a registered user code.
Important
❒ Even if you change a user code, the counter value will not be cleared.
A Press [System Settings].
7
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the user whose user code you want to change.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Auth. Info].
H Press [Change], and then enter the new user code using the number keys
I Press the {q} key.
198
Downloaded from ManualsPrinter.com Manuals
Authentication Information
J To change the available functions, press [Auth. Info] and then press [TNext]
twice.
K Press the key to select the functions to enable them.
Press the key to highlight it, and then the function is enabled. To cancel a selection, press the highlighted key.
L Press [OK].
M Press [Exit].
N Press the {User Tools/Counter} key.
Note
❒ To change the name, key display and title, see “Changing a Registered
Name”.
Reference
p.194 “Changing a Registered Name”
Deleting a User Code
This section describes how to delete registered user code.
7
Important
❒ After clearing the user code, the counter is automatically cleared.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name whose code is to be deleted.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Auth. Info].
Downloaded from ManualsPrinter.com Manuals
199
Registering Addresses and Users for Facsimile/Scanner Functions
H Press [Change] to delete the user code, and then press the {q} key.
I Press [OK].
J Press [Exit].
K Press the {User Tools/Counter} key.
Note
❒ To delete a name from the Address Book entirely, see “Deleting a Registered
Name”.
Reference
p.195 “Deleting a Registered Name”
Displaying the Counter for Each User
7
This section describes how to display the counter for each user.
A Press [System Settings].
B Press [Administrator Tools].
C Press [Display / Clear / Print Counter per User].
D Select the function usage you want to print from [Print Counter], [Transmission
Counter] or [Scanner Counter].
Counters for individual function usage under each user code appear.
200
Downloaded from ManualsPrinter.com Manuals
Authentication Information
Printing the Counter for Each User
This section describes how to print the counter for each user.
A Press [System Settings].
B Press [Administrator Tools].
C Press [Display / Clear / Print Counter per User].
D Select a user code from the left side of the display.
Press [Select All on the Page] to select all user codes on the page.
7
E Press [Print Counter List] under "Per User".
Enter the user code, and then press the {q} key if the User Code Authentication is specified.
F Select the function usage you want to print from [Print Counter], [Transmission
Counter], and [Scanner Counter].
G Press [Print].
Downloaded from ManualsPrinter.com Manuals
201
Registering Addresses and Users for Facsimile/Scanner Functions
Printing the Counter for All Users
This section describes how to print the counter for all users.
A Press [System Settings].
B Press [Administrator Tools].
C Press [Display / Clear / Print Counter per User].
D Press [Print Counter List] under "All Users".
7
Enter the user code, and then press the {q} key if the User Code Authentication is specified.
E Select the function usage you want to print from [Print Counter], [Transmission
Counter], and [Scanner Counter].
F Press [Print].
202
Downloaded from ManualsPrinter.com Manuals
Authentication Information
Clearing the Number of Prints
This section describes how to clear the counter.
A Press [System Settings].
B Press [Administrator Tools].
C Press [Display / Clear / Print Counter per User].
D Select the user code to clear.
E To clear the number of prints made under a user code, select the user code
from the left side of the display.
7
Press [Select All on the Page] to select all user codes on the page.
F Press [Clear] under "Per User".
G Select the function usage you want to clear from [Print Counter],[Transmission
Counter], and [Scanner Counter].
H Press [OK].
I To clear the number of prints for all user codes, press [Clear] under "All Users".
J Select the function usage you want to clear from [Print Counter],[Transmission
Counter], and [Scanner Counter].
K Press [OK].
L Press [Exit].
M Press the {User Tools/Counter} key.
Downloaded from ManualsPrinter.com Manuals
203
Registering Addresses and Users for Facsimile/Scanner Functions
Fax Destination
This section describes the procedure for registering, changing, and deleting Fax
Destinations.
Register a fax destination so you do not need to enter fax numbers each time, and
can send documents that have been scanned in using the facsimile function.
• It is easy to select the fax destination if you register “Name" and “Key Display" for the fax destination.
• You can register fax destinations as a group. For details about registering a
group, see "Registering Names to a Group".
• You can register fax destinations by selecting them from redial function.
• Registered Fax numbers can be used as sender's Fax numbers.
There are two types of fax destination, as shown below:
• Fax Destination
Select this to send the fax over the telephone network.
• IP-Fax
Select this to send the fax to a machine on a TCP/IP network.
You cannot send the fax to a machine on another network if that network is
behind a firewall.
You can program the following items in a fax destination:
7
❖ Fax number
Registers the destination's fax number. You can enter a fax number using up
to 128 digits. You must include every digit in the number.
❖ SUB Code
Registering a SUB Code allows you to use Confidential Transmission to send
messages to the other fax machines which support a similar function called
“SUB Code". See “SUB Code", Facsimile Reference.
❖ SEP Code
Registering a SEP Code allows you to use Polling Reception to receive faxes
from the other fax machines which support Polling Reception. See “SEP
Code", Facsimile Reference.
❖ Line
If the optional extra G3 interface unit is installed, you can select the line type
per destination.
❖ International TX mode
When setting the International TX mode to [On], the machine transmits more
carefully by lowering transmission speed. However, communication times
increase.
204
Downloaded from ManualsPrinter.com Manuals
Fax Destination
❖ Fax header
You can select to print a fax header on fax messages the other party receives.
The default is “1st Name".
❖ Label insertion
Use label insertion to print information such as the destination name on the
sheet printed out at the destination.
Data is printed as follows:
• Destination Name
The destination name specified in [Fax Destination] is printed with “To" before it at the top of the sheet.
• Standard Message
A registered two-line sentence is printed under "Destination Name".
To use this function, set Label Insertion to [On] when programming fax destinations and also press [Label Insertion] when sending fax documents.
Fax header and label insertion are also printed when sending by e-mail using
the fax function.
You can program a standard message other than those registered in the machine. See “Programming, Changing, and Deleting Standard Messages", Facsimile Reference
You can program the following items in an IP-Fax Destination:
❖ IP-Fax
Register the IP-Fax destination. You can register the name using up to 128
characters. You must make this setting when using IP-Fax.
This setting only works if the IP-Fax function has been selected.
7
❖ SUB Code
Registering a SUB Code allows you to use Confidential Transmission to send
messages to the other fax machines which support a similar function called
“SUB Code". See “SUB Code", Facsimile Reference.
❖ SEP Code
Registering a SEP Code allows you to use Polling Reception to receive faxes
from the other fax machines which support Polling Reception. See “SEP
Code", Facsimile Reference.
❖ Select Protocol
Select the protocol for the IP-Fax transmission.
This setting only works if the IP-Fax function has been selected.
Reference
p.239 “Registering Names to a Group”
p.247 “Registering a Protection Code”
Downloaded from ManualsPrinter.com Manuals
205
Registering Addresses and Users for Facsimile/Scanner Functions
Fax Destination
This section describes how to register, change, and delete a fax destination.
Registering a Fax Destination
This section describes how to register a fax number.
A Press [System Settings].
7
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name whose fax destination you want to register. Press the name
key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Fax Dest.].
H Enter the fax number using the number keys, and then press [OK] under
"Facsimile No.".
I Specify optional settings such as “SUB Code”, “SEP Code”, and “International TX Mode”.
206
Downloaded from ManualsPrinter.com Manuals
Fax Destination
J Press [OK].
Note
❒ When a group is registered, you can also add this fax destination to the
group. For details about registering groups, see "Registering Names to a
Group".
❒ To register the name, see "Registering Names".
Reference
p.192 “Registering Names”
p.46 “1”
p.207 “Selecting the line”
p.208 “Programming the SUB Code”
p.208 “Programming the SEP Code”
p.208 “Setting the International TX Mode”
p.208 “Selecting the Fax Header”
p.239 “Registering Names to a Group”
p.209 “Setting label insertion”
Using a Fax Destination as a sender
7
This section describes how to use fax destination as a sender.
A Press [Protection].
B Press [Sender] on the right side of "Use Name as".
Selecting the line
This section describes how to select the line.
A Press [Select Line].
B Select the line, and then press [OK].
Downloaded from ManualsPrinter.com Manuals
207
Registering Addresses and Users for Facsimile/Scanner Functions
Programming the SUB Code
This section describes how to program the SUB Code.
A Press [Adv. Features], and then press [SUB Code].
B Press [Change] under "TX SUB Code".
C Enter the SUB Code, and then press [OK].
D To enter the password, press [Change] under "Password (SID)".
E Enter the password, and then press [OK].
F Press [OK].
Programming the SEP Code
This section describes how to program the SEP Code.
7
A Press [Adv. Features], and then press [SEP Code].
B Press [Change] under "RX SEP Code".
C Enter the SEP Code, and then press [OK].
D To enter the password, press [Change] under "Password (PWD)".
E Enter the password, and then press [OK].
F Press [OK].
Setting the International TX Mode
This section describes how to set the International TX Mode.
A Press [Change] under "International TX Mode".
B Select [Off] or [On], and then press [OK].
Selecting the Fax Header
This section describes how to select the fax header.
You can register the fax header in Program Fax Information in the system settings for Facsimile Features.
A Press [Change] under "Fax Header".
B Select [1st Name] or [2nd Name], and then press [OK].
Reference
p.115
“Registering Fax
Information”
208
Downloaded from
ManualsPrinter.com
Manuals
Fax Destination
Setting label insertion
This section describes how to set label insertion.
When Label Insertion is set to On, the receiver's name and standard messages
are printed on the fax message when it is received at the other end.
A Press [Change] under "Label Insertion".
B Press [On].
C Press [Change] under "Line 2".
D Select a standard message or press [Custom Message] to enter the new message.
E Enter the message, and then press [OK].
F Press [OK].
G Press [Change] under "Line 3".
H Select a standard message, and then press [OK].
I Press [OK].
Note
❒ To change the name, key display and title, see “Changing a Registered Name”.
7
Reference
p.194 “Changing a Registered Name”
Changing a Fax Destination
This section describes how to change a registered fax destination.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
Downloaded from ManualsPrinter.com Manuals
209
Registering Addresses and Users for Facsimile/Scanner Functions
F Select the name whose fax destination you want to change.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Fax Dest.].
H Change the settings.
I Press [OK].
Note
❒ To change the name, key display and title, see “Changing a Registered Name”.
Reference
p.194 “Changing a Registered Name”
7
p.46 “1”
p.207 “Selecting the line”
p.208 “Programming the SUB Code”
p.208 “Programming the SEP Code”
p.208 “Setting the International TX Mode”
p.208 “Selecting the Fax Header”
p.209 “Setting label insertion”
Changing the fax number
This section describes how to change the fax number.
A Press [Change]under "Facsimile No.".
B Enter the new fax number using the number keys, and then press [OK].
210
Downloaded from ManualsPrinter.com Manuals
Fax Destination
Deleting a Fax Destination
This section describes how to delete a registered fax destination.
Important
❒ If you delete a destination that is a specified delivery destination, messages to
its registered Personal Box, for example, cannot be delivered. Be sure to check
the settings in the fax function before deleting any destinations.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name whose fax destination you want to delete.
7
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Fax Dest.].
H Press [Change] under "Facsimile No".
I Press [Delete All], and then press [OK].
J Press [OK].
K Press the {User Tools/Counter} key.
Note
❒ To delete the name, key display, and title, see “Deleting a Registered Name”.
Reference
p.195 “Deleting a Registered Name”
Downloaded from ManualsPrinter.com Manuals
211
Registering Addresses and Users for Facsimile/Scanner Functions
IP-Fax Destination
This section describes how to register, change, and delete a IP-Fax destination.
Note
❒ For details about sending an IP-Fax, "Sending by IP-Fax", Facsimile Reference.
Reference
"Sending by IP-Fax", Facsimile Reference
Registering an IP-Fax Destination
This section describes how to register an IP-Fax Destination.
A Press [System Settings].
7
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name whose IP-Fax destination you want to register.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Fax Dest.].
H Press [IP-Fax].
I Press [Change] under "IP-Fax Destination".
J Enter the IP-Fax destination.
K Press [OK].
212
Downloaded from ManualsPrinter.com Manuals
Fax Destination
L Specify optional settings such as “SUB Code”, “SEP Code”, and “Protocol”.
M Press [OK].
Note
❒ To register the name, see “Registering Names”.
Reference
p.192 “Registering Names”
p.213 “Using the IP–Fax Destination as the sender”
p.213 “Selecting the protocol”
p.213 “Programming the SUB Code”
p.214 “Programming the SEP Code”
"Entering Text", About This Machine
Using the IP–Fax Destination as the sender
This section describes how to use the IP-Fax destination as the sender.
A Press [Protection].
B Press [Sender] under "Use Name as".
7
Selecting the protocol
This section describes how to select the protocol.
A Select [H.323] or [SIP].
B Press [OK].
Programming the SUB Code
This section describes how to program the SUB Code.
A Press [Adv. Features], and then press [SUB Code].
B Press [Change] under "TX SUB Code".
C Enter the SUB Code, and then press [OK].
D To enter a password, press [Change] under "Password (SID)".
E Enter a password using the number keys, and then press [OK].
F Press [OK].
Downloaded from ManualsPrinter.com Manuals
213
Registering Addresses and Users for Facsimile/Scanner Functions
Programming the SEP Code
This section describes how to program the SEP Code.
A Press [Adv. Features], and then press [SEP Code].
B Press [Change] under "RX SEP Code".
C Enter a SEP Code using the number keys, and then press [OK].
D To enter a password, press [Change] under "Password (PWD)".
E Enter a password using the number keys, and then press [OK].
F Press [OK].
Changing a IP-Fax Destination
This section describes how to change a IP-Fax Destination.
A Press [System Settings].
7
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name whose IP-Fax destination you want to change.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Fax Dest.].
H Press [IP-Fax].
I Change the settings.
214
Downloaded from ManualsPrinter.com Manuals
Fax Destination
J Press [OK].
Note
❒ To change the name, key display and title, see “Changing a Registered Name”.
Reference
p.194 “Changing a Registered Name”
p.213 “Using the IP–Fax Destination as the sender”
p.213 “Selecting the protocol”
p.213 “Programming the SUB Code”
p.214 “Programming the SEP Code”
p.215 “Changing a registered IP-Fax Destination”
"Entering Text", About This Machine
Changing a registered IP-Fax Destination
This section describes how to change a registered IP-Fax destination.
A Press [Change] under "IP-Fax Destination".
B Enter the new destination, and then press [OK].
7
Deleting a IP-Fax Destination
This section describes how to delete a registered IP-Fax destination.
If you delete a destination that is a specified delivery destination, messages to its
registered Personal Box, for example, cannot be delivered. Be sure to check the
settings in the fax function before deleting any destinations.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
Downloaded from ManualsPrinter.com Manuals
215
Registering Addresses and Users for Facsimile/Scanner Functions
F Select the name whose IP-Fax destination you want to delete. Press the
name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Fax Dest.].
H Press [IP-Fax].
I Press [Change] under "IP-Fax Destination".
J Press [Delete All], and then press [OK].
K Press [OK].
L Press the {User Tools/Counter} key.
Note
❒ To change the name, key display and title, see “Changing a Registered Name”.
Reference
p.194 “Changing a Registered Name”
7
216
Downloaded from ManualsPrinter.com Manuals
E-mail Destination
E-mail Destination
This section describes the procedure for registering, changing, and deleting Email Destination.
Register e-mail destinations so you do not need to enter an e-mail address every
time, and can send scan files from scanner or fax function by e-mail.
• It is easy to select the e-mail destination if you register “Name" and “Key Display" as the e-mail destination.
• You can register e-mail destinations as a group.
• You can use the e-mail address as the sender's address when sending scan
files in scanner mode. If you want to do this, set a protection code on the sender address to prevent unauthorized access.
Note
❒ You can select an e-mail address from an LDAP server, and then register it in
the Address Book. See “Sending Scan File by E-mail", Scanner Reference.
❒ You can set the machine to send a Transmission Result Report by e-mail
whenever a transmission is sent. See Facsimile Reference You can set the machine to send a Transmission Result Report by e-mail whenever a transmission is sent. See Facsimile Reference.
Reference
p.247 “Registering a Protection Code”
Registering an E-mail Destination
This section describes how to register an e-mail destination.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name whose e-mail address you want to register. Press the name
key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
217
Downloaded from ManualsPrinter.com Manuals
7
Registering Addresses and Users for Facsimile/Scanner Functions
G Press [E-mail].
H Press [Change] under "E-mail Address".
I Enter the e-mail address, and then press [OK].
J If you want to use Internet fax, specify whether or not to use " Send via
SMTP Server".
K Press [OK].
L Press [Exit].
7
Note
❒ You can enter up to 128 characters for the e-mail address.
❒ To register the name, see Registering Names”.
Reference
p.192 “Registering Names”
p.197 “Registering a User Code”
p.240 “Registering Names to a Group”
Using the e-mail address as the sender
This section describes how to use the e-mail address as a sender.
A Press [Protection].
B Press [Sender] under "Use Name as".
218
Downloaded from ManualsPrinter.com Manuals
E-mail Destination
Changing an E-mail Destination
This section describes how to change an e-mail destination.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name whose e-mail address you want to change.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
7
G Press [E-mail].
H Press [Change] under "E-mail Address".
I Enter the e-mail address, and then press [OK].
J Press [OK].
Note
❒ To change the name, key display and title, see “Changing a Registered Name”.
Reference
p.194 “Changing a Registered Name”
p.218 “Using the e-mail address as the sender”
"Entering Text", About This Machine
Downloaded from ManualsPrinter.com Manuals
219
Registering Addresses and Users for Facsimile/Scanner Functions
Deleting an E-mail Destination
This section describes how to delete an e-mail destination.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name whose e-mail address you want to delete.
7
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [E-mail].
H Press [Change] under "E-mail Address".
I Press [Delete All], and then press [OK].
J Press [OK].
K Press [Exit].
L Press the {User Tools/Counter} key.
Note
❒ To delete the name, key display, and title, see “Deleting a Registered Name”.
Reference
p.195 “Deleting a Registered Name”
220
Downloaded from ManualsPrinter.com Manuals
Registering Folders
Registering Folders
This section describes the procedure for registering, changing, and deleting folders.
By registering a shared folder, you can send scan files to it directly.
There are three types of protocol you can use:
• SMB
For sending files to shared Windows folders.
• FTP
Use when sending files to an FTP server.
• NCP
Use when sending files to an NetWare server.
Note
❒ For details about protocols, server names, and folder levels, consult your network administrator.
❒ You can prevent unauthorized users from accessing folders from the machine. See "Registering a Protection Code".
❒ You can only select either SMB, FTP, or NCP. If you change protocol after finishing your settings, all previous entries are cleared.
Using SMB to Connect
7
This section describes the procedure for registering, changing, and deleting SMB
folders.
Note
❒ To register a folder in an FTP server, see “Using FTP to Connect”.
❒ To register a folder in an NetWare server, see “Using NCP to Connect”.
Reference
p.227 “Using FTP to Connect”
p.233 “Using NCP to Connect”
Registering a SMB Folder
This section describes how to register a SMB folder.
A Press [System Settings].
B Press [Administrator Tools].
Downloaded from ManualsPrinter.com Manuals
221
Registering Addresses and Users for Facsimile/Scanner Functions
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name whose folder you want to register. Press the name key, or
enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Auth. Info], and then press [TNext].
H Press [Specify Other Auth. Info] on the right side of Folder Authentication.
When [Do not Specify] is selected, the SMB User Name and SMB Password that
you have specified in Default User Name / Password (Send) of File Transfer
settings applies.
7
I Press [Change] under "Login User Name".
J Enter the login user name, and then press [OK].
K Press [Change] under "Login Password".
L Enter the password, and then press [OK].
M Enter the password again to confirm, and then press [OK].
N Press [Folder].
O Check that [SMB] is selected.
To specify a folder, you can either enter the path manually or locate the folder
by browsing the network.
P Press [Connection Test] to check the path is set correctly.
Q Press [Exit].
If the connection test fails, check the settings, and then try again.
222
Downloaded from ManualsPrinter.com Manuals
Registering Folders
R Press [OK].
S Press [Exit].
❒
❒
❒
❒
❒
Note
To register the name, see Registering Names”.
You can enter up to 64 characters for the user name.
You can enter up to 64 characters for the password.
You can enter a path using up to 128 characters.
If User Authentication is specified, contact your administrator.
Reference
p.192 “Registering Names”
p.223 “Locating the SMB folder manually”
p.224 “Locating the SMB folder using Browse Network”
Locating the SMB folder manually
This section describes how to locate the SMB folder manually.
A Press [Change] under "Path".
B Enter the path where the folder is located.
C Press [OK].
7
If the format of the entered path is not correct, a message appears. Press [Exit],
and then enter the path again.
Note
❒ Enter the path using this format: “\\ServerName\Share- Name\PathName”.
❒ You can also enter an IP address.
❒ You can enter a path using up to 128 characters.
Downloaded from ManualsPrinter.com Manuals
223
Registering Addresses and Users for Facsimile/Scanner Functions
Locating the SMB folder using Browse Network
This section describes how to locate the SMB folder using Browse Network.
A Press [Browse Network].
The client computers sharing the same network as the machine appear.
If you have already specified your user name and password in steps G to M on
"Registering a SMB Folder", the Network display only lists client computers
you are authorized to access.
B Select a client computer.
Shared folders under it appear.
You can press [Up One Level] to switch between levels.
C Select the folder you want to register, and then Press [OK].
7
If a Login Screen Appears
This section describes how to log on to the machine if the login screen appears
when you try to access a folder by browsing the network.
If you have not specified folder authentication, or if an incorrect user name or
password has been entered for folder authentication, the login screen appears.
A Enter the login user name, and then press [OK].
Enter the login user name specified for folder authentication.
B Enter the password, and then press [OK].
The path to the selected folder appears.
If a message appears, press [Exit], and then enter the login user name and
password again.
224
Downloaded from ManualsPrinter.com Manuals
Registering Folders
Changing a SMB Folder
This section describes how to change settings of the registered SMB folder.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name whose folder you want to change.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Folder].
H Select the items you want to change.
I Press [Connection Test] to check the path is set correctly.
J Press [Exit].
7
Note
❒ To change the name, key display and title, see “Changing a Registered Name”.
❒ If the connection test fails, check the settings, and then try again.
Reference
p.194 “Changing a Registered Name”
p.226 “Changing the registered SMB folder”
p.226 “To change the protocol”
Downloaded from ManualsPrinter.com Manuals
225
Registering Addresses and Users for Facsimile/Scanner Functions
Changing the registered SMB folder
This section describes how to change the registered SMB folder.
A Press [Change] under "Path".
B Enter the New path where the folder is located, and then press [OK].
You can also use Browse Network to specify a new folder. For details, see "Locating the SMB folder using Browse Network".
Reference
p.224 “Locating the SMB folder using Browse Network”
To change the protocol
This section describes how to change the protocol.
A Press [FTP] or [NCP].
7
B A confirmation message appears. Press [Yes].
Changing the protocol will clear all settings made under the previous protocol.
C Enter each item again.
Reference
p.227 “Registering a FTP Folder”
Deleting a SMB folder
This section describes how to delete the registered SMB folder.
A [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
226
Downloaded from ManualsPrinter.com Manuals
Registering Folders
E Check that [Program / Change] is selected.
F Select the name whose folder you want to delete.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Folder].
H Press the protocol which is not currently selected.
A confirmation message appears.
I Press [Yes].
J Press [OK].
K Press [Exit].
Note
❒ To delete the name, key display, and title, see “Deleting a Registered Name”.
Reference
p.195 “Deleting a Registered Name”
7
Using FTP to Connect
This section describes the procedure for registering, changing, and deleting FTP
folders.
Note
❒ To register a shared folder configured in Windows, see “Using SMB to Connect”.
❒ To register a folder in an NetWare server, see “Using NCP to Connect”.
Reference
p.221 “Using SMB to Connect”
p.233 “Using NCP to Connect”
Registering a FTP Folder
This section describes how to register an FTP folder.
A Press [System Settings].
Downloaded from ManualsPrinter.com Manuals
227
Registering Addresses and Users for Facsimile/Scanner Functions
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name whose folder you want to register.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Auth. Info], and then press [TNext].
H Press [Specify Other Auth. Info] on the right side of "Folder Authentication".
When [Do not Specify] is selected, the FTP User Name and FTP Password that
you have specified in Default User Name / Password (Send) of File Transfer
settings applies. For details, see "File Transfer".
7
I Press [Change] under "Login User Name".
J Enter the login user name, and then press [OK].
K Press [Change] under "Login Password".
L Enter the password, and then press [OK].
M Enter the password again to confirm, and then press [OK].
N Press [Folder].
O Press [FTP].
P Press [Change] under "Server Name".
Q Enter the server name, and then press [OK].
R Press [Change] under "Path".
228
Downloaded from ManualsPrinter.com Manuals
Registering Folders
S Enter the path, and then press [OK].
You can enter an absolute path, using this format: “/user/ home/username";
or a relative path, using this format: “directory/sub-directory".
If you leave the path blank, the login directory is assumed to be the current
working directory.
You can also enter an IP address.
You can enter a path using up to 128 characters.
T To change the port number, press [Change] under "Port No".
U Enter the port number using the number keys, and then press the {q} key.
You can enter 1 to 65535.
V Press [Connection Test] to check the path is set correctly.
W Press [Exit].
If the connection test fails, check the settings, and then try again.
X Press [OK].
Y Press [Exit].
Note
❒ To register the name, see Registering Names”.
❒
❒
❒
❒
7
You can enter up to 64 characters for the user name.
You can enter up to 64 characters for the password.
You can enter a server name using up to 64 characters.
If User Authentication is specified, contact your administrator.
Reference
p.192 “Registering Names”
p.223 “Locating the SMB folder manually”
p.224 “Locating the SMB folder using Browse Network”
Downloaded from ManualsPrinter.com Manuals
229
Registering Addresses and Users for Facsimile/Scanner Functions
Changing a FTP Folder
This section describes how to change the registered FTP folder.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name whose folder you want to change, and then press [Folder].
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
7
G Press [Folder].
H Select the items you want to change.
I Press [Connection Test] to check the path is set correctly.
J Press [Exit].
Note
❒ To change the name, key display and title, see “Changing a Registered Name”.
Reference
p.194 “Changing a Registered Name”
p.231 “Changing the protocol”
230
Downloaded from ManualsPrinter.com Manuals
Registering Folders
Changing the protocol
This section describes how to change the protocol.
A Press [SMB], or [NCP].
B A confirmation message appears. Press [Yes].
Changing the protocol will clear all settings made under the previous protocol.
C Enter each item again.
Reference
p.221 “Registering a SMB Folder”
Changing the registered FTP folder
This section describes how to change the registered FTP folder.
A Press [Change] under "Port No".
B Enter the new port number, and then press the {q} key.
C Press [Change] under "Server Name".
D Enter the new server name, and then press [OK].
E Press [Change] under "Path".
F Enter the new path, and then press [OK].
7
Deleting a FTP Folder
This section describes how to delete the registered FTP folder.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
Downloaded from ManualsPrinter.com Manuals
231
Registering Addresses and Users for Facsimile/Scanner Functions
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name whose folder you want to delete.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Folder].
H Press the protocol which is not currently selected.
A confirmation message appears.
I Press [Yes].
J Press [OK].
K Press [Exit].
Note
❒ To delete a name entirely, see “Deleting a Registered Name”.
7
Reference
p.195 “Deleting a Registered Name”
232
Downloaded from ManualsPrinter.com Manuals
Registering Folders
Using NCP to Connect
This section describes the procedure for registering, changing, and deleting NCP
folders.
Note
❒ To register a shared folder configured in Windows, see “Using SMB to Connect”
❒ To register a folder in an FTP server, see “Using FTP to Connect”
Reference
p.221 “Using SMB to Connect”
p.227 “Using FTP to Connect”
Registering a NCP Folder
This section describes how to register an NCP folder.
A Press [System Settings].
7
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Press the name you want to register or enter the registered number using
the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Auth. Info], and then press [TNext].
H Press [Specify Other Auth. Info] on the right side of Folder Authentication.
When [Do not Specify] is selected, the NCP User Name and NCP Password that
you have specified in Default User Name / Password (Send) of File Transfer
settings applies. For details, see "File Transfer".
I Press [Change] under "Login User Name".
J Enter the login user name, and then press [OK].
K Press [Change] under "Login Password".
Downloaded from ManualsPrinter.com Manuals
233
Registering Addresses and Users for Facsimile/Scanner Functions
L Enter the password, and then press [OK].
M Enter the password again to confirm, and then press [OK].
N Press [Folder].
O Press [NCP].
P Select "Connection Type".
If you want to specify a folder in an NDS tree, press [NDS]. If you want to specify a folder on a NetWare server, press [Bindery].
If you have set "Connection Type" to [NDS], enter the user name followed by
the name of the context where the user object is located. If the user name is
“user" and the context name is “context", enter “user.context"
Q Specify the folder, and then Press [OK].
R Press [Connection Test] to check the path is set correctly.
S Press [Exit].
Note
❒ You can enter up to 64 characters for the user name.
7
❒ You can enter up to 64 characters for the password.
❒ To specify a folder, you can either enter the path manually or locate the
folder by browsing the network.
❒ If User Authentication is specified, contact your administrator.
Reference
p.192 “Registering Names”
p.235 “Locate the NCP folder manually”
p.235 “Locating the NCP folder using Browse Network”
"Entering Text", About This Machine
234
Downloaded from ManualsPrinter.com Manuals
Registering Folders
Locate the NCP folder manually
This section describes how to locate the NCP folder manually.
A Press [Change] under "Path".
B Enter the path where the folder is located.
C Press [OK].
Note
❒ If you set "Connection Type" to [NDS], and if the NDS tree name is "tree",
the name of the context including the volume is "context", the volume
name is "volume" and the folder name is "folder", then the path will be
"\\tree\volume. context\folder".
❒ If you set "Connection Type" to [Bindery], and if the NetWare server name
is "server", the volume name is "volume" and the folder name is "folder",
then the path will be "\\server\volume\folder".
❒ You can enter a path using up to 128 characters.
❒ If the connection test fails, check the settings, and then try again.
Locating the NCP folder using Browse Network
This section describes how to locate the NCP folder using Browse Network.
7
A Press [Browse Network].
B Search for the destination folder in the NDS tree or NetWare server.
You can press [Up One Level] to switch between levels.
If you have set "Connection Type" to [NDS], a list of items in the NDS tree appears. If you have set "Connection Type" to [Bindery], a list of items on the NetWare server appears.
C Select the folder you want to register, and then press [OK].
Note
❒ Only the folders you are allowed to access appear in [Browse Network].
❒ If the languages used on the machine and the destination you want to view
differ, the items in the list may not appear correctly.
❒ Up to 100 items can be displayed in the list.
Downloaded from ManualsPrinter.com Manuals
235
Registering Addresses and Users for Facsimile/Scanner Functions
Changing a NCP folder
This section describes how to change the registered NCP folder.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the user of the registered folder you want to change.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
7
G Press [Folder].
H Select "Connection Type".
If you want to specify a folder in an NDS tree, press [NDS]. If you want to specify a folder on a NetWare server, press [Bindery].
I Specify the folder.
J Press [Connection Test] to check the path is set correctly.
K Press [Exit].
Note
❒ To change the name, key display and title, see “Changing a Registered Name”.
Reference
p.194 “Changing a Registered Name”
p.237 “Changing the registered NCP folder”
236
Downloaded from ManualsPrinter.com Manuals
Registering Folders
Changing the registered NCP folder
This section describes how to change the register NCP folder.
A Press [Change] under "Path".
B Enter the path where the folder is located, and then press [OK].
You can also use Browse Network to specify a new folder. For details, see "Locating the NCP folder manually".
Reference
p.235 “Locate the NCP folder manually”
p.235 “Locating the NCP folder using Browse Network”
p.237 “Changing the protocol”
Changing the protocol
This section describes how to change the protocol.
A Press [SMB], or [FTP].
B A confirmation message appears. Press [Yes].
Changing the protocol will clear all settings made under the previous protocol.
7
C Enter each item again.
Reference
p.221 “Registering a SMB Folder”
p.227 “Registering a FTP Folder”
Downloaded from ManualsPrinter.com Manuals
237
Registering Addresses and Users for Facsimile/Scanner Functions
Deleting an NCP Folder
This section describes how to delete the registered NCP folder.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select a user of the folder you want to delete.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
7
G Press [Folder].
H Press the protocol which is not currently selected.
A confirmation message appears.
I Press [Yes].
J Press [OK].
K [Exit].
Note
❒ To delete a name entirely, see Deleting a Registered Name”.
Reference
p.195 “Deleting a Registered Name”
238
Downloaded from ManualsPrinter.com Manuals
Registering Names to a Group
Registering Names to a Group
This section describes how to register names to a group.
You can register names to a group to enable easy management of e-mail addresses and folders for each group.
To add names to a group, the groups must be registered beforehand.
Important
❒ When using Scan to Folder function, you cannot send scan files to a group
with over 50 folders registered.
❒ You can register up to 100 groups.
Note
❒ You can set a protection code to prevent unauthorized access to the folders
registered in a group. For details, see “Registering a Protection Code".
Reference
p.247 “Registering a Protection Code”
Registering a Group
This section describes how to register a group.
7
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book: Program / Change / Delete Group].
E Check that [Program / Change] is selected.
F Press [New Program].
G Press [Change] under "Group Name".
Downloaded from ManualsPrinter.com Manuals
239
Registering Addresses and Users for Facsimile/Scanner Functions
H Enter the group name, and then press [OK].
The key display name is set automatically.
I When you want to change the key display, press [Change] under "Key Display".
J Enter the key display, and then press [OK].
K Press the title key under Select Title, if necessary.
The keys you can select are as follows:
• [Freq.]: Added to the page that is displayed first.
• [AB], [CD], [EF], [GH], [IJK], [LMN], [OPQ], [RST], [UVW], [XYZ], [1] to [10]…
Added to the list of items in the selected title.
You can select [Freq.] and one more page for each title.
L Press [OK].
Reference
"Entering Text", About This Machine
Registering Names to a Group
7
This section describes how to register names to a registered group.
You can put names that have been registered in the Address Book into a group.
When registering new names, you can also register groups at the same time.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name to register in a group.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Add to Group].
240
Downloaded from ManualsPrinter.com Manuals
Registering Names to a Group
H Select a group to which you want to add the name to.
The group key that you have selected becomes highlighted, and the name is
added to it.
I Press [OK].
Adding a Group to Another Group
This section describes how to add a group to another group.
A Press [System Settings].
7
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book: Program / Change / Delete Group].
E Check that [Program / Change] is selected.
F Select the group that you want to put into another group.
Press the group key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Add to Group].
Downloaded from ManualsPrinter.com Manuals
241
Registering Addresses and Users for Facsimile/Scanner Functions
H Select the group which you want to add to.
The group key that you have selected becomes highlighted, and the group is
added to it.
I Press [OK].
Displaying Names Registered in a Group
This section describes how to display names registered in a group.
You can check the names or groups registered in each group.
7
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book: Program / Change / Delete Group].
E Check that [Program / Change] is selected.
F Select the group where the members you want to check is registered.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Programd. User/Group].
All the names registered will be displayed.
H Press [OK].
242
Downloaded from ManualsPrinter.com Manuals
Registering Names to a Group
Removing a Name from a Group
This section describes how to remove a name from a group.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name to remove from a group.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
7
G Press [Add to Group].
H Select the group from which you want to remove the name.
The group key that you have selected becomes highlighted, and the name is
added to it.
I Press [OK].
Downloaded from ManualsPrinter.com Manuals
243
Registering Addresses and Users for Facsimile/Scanner Functions
Deleting a Group Within Another Group
This section describes how to delete a group within another group.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book: Program / Change / Delete Group].
E Check that [Program / Change] is selected.
F Select the group that you want to delete from.
7
Press the group key, or enter the registered number during the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Add to Group].
The keys of groups in which the group is registered appear highlighted.
H Select the group that you want to delete from.
The group key is deselected and the group is deleted from it.
I [OK].
244
Downloaded from ManualsPrinter.com Manuals
Registering Names to a Group
Changing a Group Name
This section describes how to change a group name.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book: Program / Change / Delete Group].
E Check that [Program / Change] is selected.
F Press the group key you want to change.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G To change the group name and key display, press [Change] under "Group
7
Name" or "Key Display".
H Enter the new group name or key display, and then press [OK].
I To change the title, press the title key under Select Title.
J To change the registration number, press [Change] under "Registration No".
K Enter the new registration number using the number keys, then Press the
{q} key.
L Press [OK].
Downloaded from ManualsPrinter.com Manuals
245
Registering Addresses and Users for Facsimile/Scanner Functions
Deleting a Group
This section describes how to delete a group
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book: Program / Change / Delete Group].
E Press [Delete].
F Press a group key you want to delete.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
7
G Press [Yes].
246
Downloaded from ManualsPrinter.com Manuals
Registering a Protection Code
Registering a Protection Code
This section describes how to register a Protection Code.
You can stop sender's names or folders being accessed by setting a protection
code.
You can use this function to protect the following:
• Folders
You can prevent unauthorized access to folders.
• Sender's names
You can prevent misuse of sender's names.
Reference
p.197 “Registering a User Code”
Registering a Protection Code to a Single User
This section describes how to register a Protection code to a single user.
A Press [System Settings].
7
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Select the name whose protection code you want to register.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Protection].
Downloaded from ManualsPrinter.com Manuals
247
Registering Addresses and Users for Facsimile/Scanner Functions
H Press [Destination] or [Sender] under "Use Name as".
Both [Destination] and [Sender] can be selected at the same time.
I Press [Folder Destination] or [Sender] under "Protection Object".
Both [Folder Destination] and [Sender] can be selected at the same time.
J Press [Change] under "Protection Code".
K Enter a protection code using the number keys, and then press the {q} key.
L Press [OK].
M Press [Exit].
Note
❒ Specify a protection code of up to eight digits. You can also specify “Protection” without specifying a protection code.
7
248
Downloaded from ManualsPrinter.com Manuals
Registering a Protection Code
Registering a Protection Code to a Group User
This section describes how to register a Protection Code to a Group User.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book: Program / Change / Delete Group].
E Check that [Program / Change] is selected.
F Press the group key you want to register or enter the registered number us-
ing the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Protection].
H Press [Folder Destination] under "Protection Object".
7
I Press [Change] under "Protection Code".
J Enter a protection code using the number keys, and then press the {q} key.
K Press [OK].
L Press [Exit].
Note
❒ Specify a protection code of up to eight digits. You can also specify “Protection” without specifying a protection code.
Downloaded from ManualsPrinter.com Manuals
249
Registering Addresses and Users for Facsimile/Scanner Functions
Registering the Transfer Request
This section describes how to register the Transfer Station and Receiving Station
used in the fax function's Transfer Request.
Before you can use Transfer Request, you must program the Polling ID and set
the Transfer Report. See “Polling Transmission”and “Transfer Request”, Facsimile Reference.
Important
❒ When messages are transferred by fax, Transfer Stations must be machines of
the same manufacturer as this one, and have the Transfer Station function.
❒ When messages are transferred by e-mail, Transfer Stations must be machines of the same manufacturer as this one, and have both the Transfer Station and Internet Fax functions.
❒ You cannot use Transfer Request without programming the fax number or email address of the Requesting Party in the Address Book of the Transfer Stations.
❖ Transfer Station
Refers to the machine that receives the Transfer Request to forward incoming
messages to another destination.
7
❖ Receiving Station
Refers to the facsimile or computer that receives messages from the Transfer
Station.
Note
❒ Polling IDs of the Requesting Party (this machine) and Transfer Stations must
be identical.
❒ You can have up to 30 Receiving Stations per Transfer Station. If you specify
a Transfer Station Group, the group counts as a single receiver.
Reference
“Polling Transmission”, Facsimile Reference
“Transfer Request”, Facsimile Reference
250
Downloaded from ManualsPrinter.com Manuals
Registering the Transfer Request
Registering a Transfer Station / Receiving Station
This section describes how to register a Transfer Station / Receiving Station.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book: Program / Change / Delete Transfer Request].
E Check that [Program / Change] is selected.
F Press [New Program].
G Set the Transfer Request's information.
To register the Transfer Request name and key display, see "Registering the
Transfer Request Name and Key Display".
To select the title, see "Selecting the Title".
7
H Press [Fax Destination].
I Enter the items. See step H and I on "Registering a Fax Destination".
J Press [E-mail Address].
K Enter the items. See step H to K on "Registering an E-mail Destination".
L Press [IP-Fax].
M Enter the items. See step I to L on "Registering an IP-Fax Destination".
N Press [Receiving Statn.].
Downloaded from ManualsPrinter.com Manuals
251
Registering Addresses and Users for Facsimile/Scanner Functions
O Specify the Receiving Stations.
When specifying the Receiving Stations, use the numbers stored in Quick Dial
keys, or Groups in the Transfer Station.
To specify the Quick Dial, see "Quick Dial".
To specify the Speed Dial, see "Speed Dial".
To specify the Group Dial, see "Group Dial".
P When you have specified all the Receiving Stations, press [OK].
Q Press [Exit].
Reference
p.206 “Registering a Fax Destination”
p.212 “Registering an IP-Fax Destination”
p.217 “Registering an E-mail Destination”
p.252 “Registering the Transfer Request Name and Key Display”
p.252 “Selecting the Title”
Registering the Transfer Request Name and Key Display
7
This section describes how to register the Transfer Request Name and Key Display
A Press [Change] under "Transfer Request Name" or "Key Display".
The name entry display appears.
B Enter the Transfer Request name or key display.
C Press [OK].
Reference
"Entering Text", About This Machine
Selecting the Title
This section describes how to select the Title.
A To associate a Transfer Request name with a title, press the title key under
"Select Title".
The keys you can select are as follows:
• [Freq.]: Added to the page that is displayed first.
• [AB], [CD], [EF], [GH], [IJK], [LMN], [OPQ], [RST], [UVW], [XYZ], [1] to [10]: Added to the list of items in the selected title.
You can select [Freq.] and one more page for each title.
252
Downloaded from ManualsPrinter.com Manuals
Registering the Transfer Request
Quick Dial
This section describes how to specify the Quick Dial.
A Press [qQuick Dial].
B Enter the number stored in the Quick Dial of the Transfer Station using the
number keys, and then press [OK].
For example, to select the destination stored in Quick Dial 01 of the Transfer
Station, enter {0}{1}.
C To specify an additional Receiving Station, press [Add].
Speed Dial
This section describes how to specify the Speed Dial.
A Press [qpSpeed Dial].
B Enter the Speed Dial number using the number keys, and then press [OK].
For example, to select the destination stored in Speed Dial 12 of the Transfer
Station, enter {1}{2}.
C To specify an additional Receiving Station, press [Add].
7
Group Dial
This section describes how to specify the Group Dial.
A Press [qppGroup Dial].
B Enter the Group number using the number keys, and then press [OK].
For example, to select the destinations stored in Group 04 of the Transfer Station, enter {0}{4}.
C To specify an additional Receiving Station, press [Add].
Downloaded from ManualsPrinter.com Manuals
253
Registering Addresses and Users for Facsimile/Scanner Functions
Changing a Transfer Station / Receiving Station
This section describes how to change the Transfer Station / Receiving Station.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book: Program / Change / Delete Transfer Request].
E Select the name whose Transfer Station/Receiving Station you want to
change.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
F Enter the items.
7
To change the Transfer Request name and key display, see “Changing the
Transfer Request Name and Key Display”.
To change the title, see “Changing the Title”.
To change the Fax Station, see “Changing the Fax Station”.
To change the IP-Fax Station, see “Changing the IP-Fax Station”.
To change the E-mail Transfer Station, see “Changing the E-mail Transfer Station”.
To change the Receiving Station, see “Changing the Receiving Station”.
G Press [OK].
H Press [Exit].
Note
❒ To change the name, key display, and title, see “Changing a Registered Name”.
Reference
p.194 “Changing a Registered Name”
p.255 “Changing the Transfer Request Name and Key Display”
p.255 “Changing the Title”
p.255 “Changing the Fax Transfer Station”
p.255 “Changing the IP-Fax Transfer Station”
p.256 “Changing the E-mail Transfer Station”
p.256 “Changing the Receiving Station”
254
Downloaded from ManualsPrinter.com Manuals
Registering the Transfer Request
Changing the Transfer Request Name and Key Display
This section describes how to change the Transfer Request Name and Key Display
A Press [Change] under "Transfer Request Name" or "Key Display".
B Enter the new Transfer Request name or key display, and then press [OK].
Changing the Title
This section describes how to change the Title.
A Press the title key under "Select Title".
Changing the Fax Transfer Station
This section describes how to change the Fax Station.
A Press [Fax Destination].
Proceed to step A of "Changing the E-mail Transfer Station" when messages
are transferred by e-mail.
B Change the Transfer Station's information. See step H on "Changing a Reg-
7
istered Fax Destination".
Reference
p.209 “Changing a Fax Destination”
Changing the IP-Fax Transfer Station
This section describes how to change the IP-Fax Station.
A Press [IP-Fax].
B Change the Transfer Station's information. See step I and J on "Changing
a Registered IP-Fax Destination".
Reference
p.214 “Changing a IP-Fax Destination”
Downloaded from ManualsPrinter.com Manuals
255
Registering Addresses and Users for Facsimile/Scanner Functions
Changing the E-mail Transfer Station
This section describes how to change the E-mail Transfer Station.
A Press [E-mail].
B Change the Transfer Station's information. See step H and I "Changing a
Registered E-mail Destination".
Reference
p.219 “Changing an E-mail Destination”
Changing the Receiving Station
This section describes how to change the Receiving Station.
A Press [Receiving Statn.].
B Select the Receiving Station you want to change.
C Press [Clear] to clear the number, and then enter the new number using the
number keys.
D Press [OK].
7
256
Downloaded from ManualsPrinter.com Manuals
Registering the Transfer Request
Deleting a Transfer Station / Receiving Station
This section describes how to delete the Transfer Station / Receiving Station.
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book: Program / Change / Delete Transfer Request].
E Press [Delete].
F Select the name whose Transfer Station / Receiving Station you want to delete.
Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Yes].
H Press [Exit].
Note
❒ To delete the name, key display, and title, see “Deleting a Registered Name”.
7
Reference
p.195 “Deleting a Registered Name”
Downloaded from ManualsPrinter.com Manuals
257
Registering Addresses and Users for Facsimile/Scanner Functions
Registering SMTP and LDAP Authentication
This section describes how to register SMTP and LDAP Authentication.
SMTP Authentication
This section describes how to register SMTP Authentication.
For each user registered in the Address Book, you can register a login user name
and login password to be used when accessing an SMTP server.
To use an SMTP server, you need to program it beforehand.
Important
❒ When [Do not Specify] is selected for SMTP Authentication, the User Name and
Password that you have specified in SMTP Authentication of File Transfer
settings applies. For details, see "File Transfer".
A Press [System Settings].
7
B Press [Administrator Tools].
C Press [TNext].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Press the name you want to register or enter the registered number using
the number keys
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Auth. Info].
H Press [Specify Other Auth. Info] on the right side of SMTP Authentication.
I Press [Change] under "Login User Name".
258
Downloaded from ManualsPrinter.com Manuals
Registering SMTP and LDAP Authentication
J Enter the login user name, and then press [OK].
K Press [Change] under "Login Password".
L Enter the password, and then press [OK].
M Enter the password again to confirm, and then press [OK].
N [OK].
Note
❒ To register the name, see Registering Names”.
❒ You can enter up to 191 characters for the user name.
❒ You can enter up to 128 characters for the password.
❒ When using POP before SMTP Authentication, you can enter up to 191
characters for the user name, and 128 characters for the password.
❒ To change the SMTP Authentication settings, repeat stepB to N.
Reference
p.192 “Registering Names”
p.13 “Network Settings”
"Entering Text", About This Machine
7
LDAP Authentication
This section describes how to register LDAP Authentication.
For each user registered in the Address Book, you can register a login user name
and login password to be used when accessing an LDAP server.
To use an LDAP server, you need to program it beforehand. For details, see
“LDAP Server Settings", Network Guide.
Important
❒ When [Do not Specify] is selected for LDAP Authentication, the User Name
and Password that you have specified in Program / Change LDAP Server of
Administrator Tools settings applies. For details, see "LDAP Server Settings".
A Press [System Settings].
B Press [Administrator Tools].
C Press [TNext].
Downloaded from ManualsPrinter.com Manuals
259
Registering Addresses and Users for Facsimile/Scanner Functions
D Press [Address Book Management].
E Check that [Program / Change] is selected.
You can search by the registered name, user code, fax number, folder name,
e-mail address, or IP-Fax destination.
F Press the name you want to register or enter the registered number using
the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.
G Press [Auth. Info], and then press [TNext].
H Press [Specify Other Auth. Info] on the right side of "LDAP Authentication".
I Press [Change] under "Login User Name".
7
J Enter the login user name, and then press [OK].
K Press [Change] under "Login Password".
L Enter the password, and then press [OK].
M Enter the password again to confirm, and then press [OK].
N Press [OK].
❒
❒
❒
❒
Note
To register the name, see Registering Names”.
You can enter up to 128 characters for the user name.
You can enter up to 128 characters for the password.
To change the LDAP Authentication settings, repeat stepB to N.
Reference
p.192 “Registering Names”
"Entering Text", About This Machine
260
Downloaded from ManualsPrinter.com Manuals
8. Other User Tools
Initial settings allow you switch the language as well as checking the number of
printed papers by displaying the counter. For the details on how to access respective settings, see "Accessing User Tools".
Changing the Display Language
You can change the language used on the display. English is set as default.
A Press [Français].
The language is changed to French.
B Press [Sortie].
The menu appears in French.
Reference
p.3 “Accessing User Tools”
Downloaded from ManualsPrinter.com Manuals
261
Other User Tools
Inquiry
The inquiry function lets you check the telephone numbers to contact for repairs,
or ordering consumables such as toner. Be sure to contact your service engineer
to verify the following:
❖ Consumables
• Telephone No. to order
• Toner
• Staple
• TX Stamp Name
❖ Machine Maintenance/Repair
• Telephone No.
• Serial No. of Machine
❖ Sales Representative
• Telephone No.
A Press [Inquiry].
8
Inquiry information appears.
B Press [Print Inquiry List].
C Press the {Start} key.
Inquiry information prints out.
D Press [Exit] twice.
Reference
p.3 “Accessing User Tools”
262
Downloaded from ManualsPrinter.com Manuals
Counter
Counter
Displaying the Total Counter
You can display the total counter value used for all functions.
A Press [Counter].
B To print a counter list, press [Print Counter List].
C Press the {Start} key.
A counter list prints out.
Reference
p.3 “Accessing User Tools”
Downloaded from ManualsPrinter.com Manuals
8
263
Other User Tools
8
264
Downloaded from ManualsPrinter.com Manuals
9. Appendix
Copyrights
expat
• The software including controller, etc. (hereinafter "software") installed on
this product uses the expat under the conditions mentioned below.
• The product manufacturer provides warranty and support to the software of
the product including the expat, and the product manufacturer makes the initial developer and copyright holder of the expat, free from these obligations.
• Information relating to the expat is available at:
http://expat.sourceforge.net/
Copyright (c) 1998, 1999, 2000 Thai Open Source Software Centre, Ltd. and Clark
Cooper.
Copyright © 2001, 2002 Expat maintainers.
Permission is hereby granted, free of charge, to any person obtaining a copy of
this software and associated documentation files (the "Software"), to deal in the
Software without restriction, including without limitation the rights to use,
copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all
copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION
WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Downloaded from ManualsPrinter.com Manuals
265
Appendix
NetBSD
9
1. Copyright Notice of NetBSD
For all users to use this product:
This product contains NetBSD operating system:
For the most part, the software constituting the NetBSD operating system is not
in the public domain; its authors retain their copyright.
The following text shows the copyright notice used for many of the NetBSD
source code. For exact copyright notice applicable for each of the files/binaries,
the source code tree must be consulted.
A full source code can be found at http://www.netbsd.org/.
Copyright © 1999, 2000 The NetBSD Foundation, Inc.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
A Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
B Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
C All advertising materials mentioning features or use of this software must
display the following acknowledgment:
This product includes software developed by The NetBSD Foundation, Inc.
and its contributors.
D Neither the name of The NetBSD Foundation nor the names of its contributors may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND
CONTRIBUTORS ''AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
266
Downloaded from ManualsPrinter.com Manuals
Copyrights
2.Authors Name List
All product names mentioned herein are trademarks of their respective owners.
The following notices are required to satisfy the license terms of the software
that we have mentioned in this document:
• This product includes software developed by the University of California,
Berkeley and its contributors.
• This product includes software developed by Jonathan R. Stone for the NetBSD Project.
• This product includes software developed by the NetBSD Foundation, Inc.
and its contributors.
• This product includes software developed by Manuel Bouyer.
• This product includes software developed by Charles Hannum.
• This product includes software developed by Charles M. Hannum.
• This product includes software developed by Christopher G. Demetriou.
• This product includes software developed by TooLs GmbH.
• This product includes software developed by Terrence R. Lambert.
• This product includes software developed by Adam Glass and Charles Hannum.
• This product includes software developed by Theo de Raadt.
• This product includes software developed by Jonathan Stone and Jason R.
Thorpe for the NetBSD Project.
• This product includes software developed by the University of California,
Lawrence Berkeley Laboratory and its contributors.
• This product includes software developed by Christos Zoulas.
• This product includes software developed by Christopher G. Demetriou for
the NetBSD Project.
• This product includes software developed by Paul Kranenburg.
• This product includes software developed by Adam Glass.
• This product includes software developed by Jonathan Stone.
• This product includes software developed by Jonathan Stone for the NetBSD
Project.
• This product includes software developed by Winning Strategies, Inc.
• This product includes software developed by Frank van der Linden for the
NetBSD Project.
• This product includes software developed for the NetBSD Project by Frank
van der Linden
• This product includes software developed for the NetBSD Project by Jason R.
Thorpe.
• The software was developed by the University of California, Berkeley.
• This product includes software developed by Chris Provenzano, the University of California, Berkeley, and contributors.
Downloaded from ManualsPrinter.com Manuals
9
267
Appendix
Sablotron
Sablotron (Version 0.82) Copyright © 2000 Ginger Alliance Ltd. All Rights Reserved
a) The application software installed on this product includes the Sablotron software Version 0.82 (hereinafter, "Sablotron 0.82"), with modifications made by
the product manufacturer. The original code of the Sablotron 0.82 is provided by
Ginger Alliance Ltd., the initial developer, and the modified code of the Sablotron 0.82 has been derived from such original code provided by Ginger Alliance
Ltd.
b) The product manufacturer provides warranty and support to the application
software of this product including the Sablotron 0.82 as modified, and the product manufacturer makes Ginger Alliance Ltd., the initial developer of the Sablotron 0.82, free from these obligations.
c) The Sablotron 0.82 and the modifications thereof are made available under the
terms of Mozilla Public License Version 1.1 (hereinafter, "MPL 1.1"), and the application software of this product constitutes the "Larger Work" as defined in
MPL 1.1. The application software of this product except for the Sablotron 0.82
as modified is licensed by the product manufacturer under separate agreement(s).
d) The source code of the modified code of the Sablotron 0.82 is available at: http://support-download.com/services/device/sablot/notice082.html
e) The source code of the Sablotron software is available at: http://www.gingerall.com
f) MPL 1.1 is available at: http://www.mozilla.org/MPL/MPL-1.1.html
9
JPEG LIBRARY
• The software installed on this product is based in part on the work of the Independent JPEG Group.
268
Downloaded from ManualsPrinter.com Manuals
Copyrights
SASL
CMU libsasl
Tim Martin
Rob Earhart
Rob Siemborski
Copyright (c) 2001 Carnegie Mellon University. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
A Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
B Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
C The name "Carnegie Mellon University" must not be used to endorse or promote products derived from this software without prior written permission.
For permission or any other legal details, please contact:
Office of Technology Transfer
Carnegie Mellon University
5000 Forbes Avenue
Pittsburgh, PA 15213-3890
(412) 268-4387, fax: (412) 268-7395
tech-transfer@andrew.cmu.edu
D Redistributions of any form whatsoever must retain the following acknowledgment:
"This product includes software developed by Computing Services at Carnegie Mellon University (http://www.cmu.edu/computing/)."
CARNEGIE MELLON UNIVERSITY DISCLAIMS ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL CARNEGIE
MELLON UNIVERSITY BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING
FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF
CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT
OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS
SOFTWARE.
Downloaded from ManualsPrinter.com Manuals
9
269
Appendix
MD4
Copyright (C) 1990-2, RSA Data Security, Inc. All rights reserved.
License to copy and use this software is granted provided that it is identified as
the "RSA Data Security, Inc. MD4 Message-Digest Algorithm" in all material
mentioning or referencing this software or this function.
License is also granted to make and use derivative works provided that such
works are identified as "derived from the RSA Data Security, Inc. MD4 MessageDigest Algorithm" in all material mentioning or referencing the derived work.
RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or the suitability of this software for any particular
purpose. It is provided "as is" without express or implied warranty of any kind.
These notices must be retained in any copies of any part of this documentation
and/or software.
MD5
Copyright (C) 1991-2, RSA Data Security, Inc. Created 1991. All rights reserved.
9
License to copy and use this software is granted provided that it is identified as
the "RSA Data Security, Inc. MD5 Message-Digest Algorithm" in all material
mentioning or referencing this software or this function.
License is also granted to make and use derivative works provided that such
works are identified as "derived from the RSA Data Security, Inc. MD5 MessageDigest Algorithm" in all material mentioning or referencing the derived work.
RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or the suitability of this software for any particular
purpose. It is provided "as is" without express or implied warranty of any kind.
These notices must be retained in any copies of any part of this documentation
and/or software.
270
Downloaded from ManualsPrinter.com Manuals
Copyrights
Samba(Ver 3.0.4)
For SMB transmission, this machine uses Samba ver 3.0.4 (hereinafter referred to
as Samba 3.0.4).
Copyright © Andrew Tridgell 1994-1998
This program is free software; you can redistribute it and/or modify it under the
terms of the GNU General Public License as published by the Free Software
Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT
ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
License along with this program; if not, write to the Free Software Foundation,
Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
Note
❒ The source code for SMB transmission by this machine can be downloaded
from the following website:
http://support-download.com/services/scbs
RSA BSAFE®
9
• This product includes RSA BSAFE© cryptographic or security protocol software from RSA Security Inc.
• RSA and BSAFE are registered trademarks of RSA Security Inc. in the United
States and/or other countries.
• RSA Security Inc. All rights reserved.
Downloaded from ManualsPrinter.com Manuals
271
Appendix
Open SSL
Copyright (c) 1998-2004 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit.
(http://www.openssl.org/)"
4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact openssl-core@openssl.org.
9
5. Products derived from this software may not be called "OpenSSL" nor may
"OpenSSL" appear in their names without prior written permission of the
OpenSSL Project.
6. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes software developed by the OpenSSL Project for
use in the OpenSSL Toolkit (http://www.openssl.org/)"
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS'' AND
ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE from
POSSIBILITY
OF SUCH
DAMAGE.
272
Downloaded
ManualsPrinter.com
Manuals
Copyrights
This product includes cryptographic software written by Eric Young
(eay@cryptsoft.com). This product includes software written by Tim Hudson
(tjh@cryptsoft.com).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved.
This package is an SSL implementation written by Eric Young (eay@cryptsoft.com).
The implementation was written so as to conform with Netscapes SSL.
This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found
in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL
code. The SSL documentation included with this distribution is covered by the
same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.com).
Note that any information and cryptographic algorithms used in this software
are publicly available on the Internet and at any major bookstore, scientific library, and patent office worldwide. More information can be found e.g. at "http://www.cs.hut.fi/crypto".
The legal status of this program is some combination of all these permissions
and restrictions. Use only at your own responsibility. You will be responsible for
any legal consequences yourself; I am not making any claims whether possessing or using this is legal or not in your country, and I am not taking any responsibility on your behalf.
9
NO WARRANTY
BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO
WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM
"AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE
PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE,
YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR
CORRECTION.
Downloaded from ManualsPrinter.com Manuals
273
Appendix
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO
IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY
WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT
NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE
OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN
IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
2)
The 32-bit CRC compensation attack detector in deattack.c was contributed by
CORE SDI S.A. under a BSD-style license.
9
Cryptographic attack detector for ssh - source code
Copyright (c) 1998 CORE SDI S.A., Buenos Aires, Argentina.
All rights reserved. Redistribution and use in source and binary forms, with or
without modification, are permitted provided that this copyright notice is retained.
THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
WARRANTIES ARE DISCLAIMED. IN NO EVENT SHALL CORE SDI S.A. BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OR MISUSE OF THIS SOFTWARE.
Ariel Futoransky <futo@core-sdi.com>
<http://www.core-sdi.com>
3)
One component of the ssh source code is under a 3-clause BSD license, held by
the University of California, since we pulled these parts from original Berkeley
code.
Copyright (c) 1983, 1990, 1992, 1993, 1995
The Regents of the University of California. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
274
Downloaded from ManualsPrinter.com Manuals
Copyrights
2. Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
3. Neither the name of the University nor the names of its contributors may be
used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS
``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
4)
Remaining components of the software are provided under a standard 2-term
BSD licence with the following names as copyright holders:
Markus Friedl
Theo de Raadt
Niels Provos
Dug Song
Kevin Steves
Daniel Kouril
Wesley Griffin
Per Allansson
Jason Downs
Solar Designer
Todd C. Miller
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
Downloaded from ManualsPrinter.com Manuals
9
275
Appendix
THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
5)
Portable OpenSSH contains the following additional licenses:
c) Compatibility code (openbsd-compat)
Apart from the previously mentioned licenses, various pieces of code in the
openbsd-compat/ subdirectory are licensed as follows:
Some code is licensed under a 3-term BSD license, to the following copyright
holders:
9
Todd C. Miller
Theo de Raadt
Damien Miller
Eric P. Allman
The Regents of the University of California
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
3. Neither the name of the University nor the names of its contributors may be
used to endorse or promote products derived from this software without specific prior written permission.
276
Downloaded from ManualsPrinter.com Manuals
Copyrights
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS
``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Open LDAP
The OpenLDAP Public License Version 2.8, 17 August 2003
Redistribution and use of this software and associated documentation ("Software"), with or without modification, are permitted provided that the following
conditions are met:
1. Redistributions in source form must retain copyright statements and notices,
2. Redistributions in binary form must reproduce applicable copyright statements and notices, this list of conditions, and the following disclaimer in the
documentation and/or other materials provided with the distribution, and
9
3. Redistributions must contain a verbatim copy of this document.
The OpenLDAP Foundation may revise this license from time to time. Each revision is distinguished by a version number. You may use this Software under
terms of this license revision or under the terms of any subsequent revision of
the license.
Downloaded from ManualsPrinter.com Manuals
277
Appendix
THIS SOFTWARE IS PROVIDED BY THE OPENLDAP FOUNDATION AND
ITS CONTRIBUTORS ``AS IS'' AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OPENLDAP
FOUNDATION, ITS CONTRIBUTORS, OR THE AUTHOR(S) OR OWNER(S)
OF THE SOFTWARE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
The names of the authors and copyright holders must not be used in advertising
or otherwise to promote the sale, use or other dealing in this Software without
specific, written prior permission. Title to copyright in this Software shall at all
times remain with copyright holders.
OpenLDAP is a registered trademark of the OpenLDAP Foundation.
Copyright 1999-2003 The OpenLDAP Foundation, Redwood City, California,
USA. All Rights Reserved. Permission to copy and distribute verbatim copies of
this document is granted.
9
278
Downloaded from ManualsPrinter.com Manuals
INDEX
C
1 Sided → 2 Sided Auto Margin: TtoB, 82
1 Sided → 2 Sided Auto Margin: TtoT, 82
2 Sided Print (Available only with the
optional duplex unit and HDD), 99
A
Accessing User Tools (System Settings), 3
Address Book: Change Order, 62
Address Book: Edit Title, 62
Address Book: Program / Change /
Delete Group, 62
Address Book: Program / Change /
Delete Transfer Request, 62
Address Book: Select Title, 62
Address Book Management, 62
Adjust Scan Density, 95
Adjust Sound Volume, 95
Administrator Authentication
Management, 62
Administrator's E-mail Address, 55
Administrator Tools / Facsimile Features, 107
Administrator Tools / System Settings, 62
AOF (Always On), 62
Append CR to LF, 175
Authorized Reception, 138
Authorized RX, 147
Authorized RX (Authorized Reception), 99
Auto Continue, 171
Auto Delete File in Document Server, 62
Auto Delete Stored Print Jobs, 171
Auto Delete Temporary Print Jobs, 171
Auto Image Density, 95
Auto Image Density Priority, 75
Auto Logout Timer, 47
Auto Off Timer, 47
Auto Paper Select Priority, 75
Auto Sort, 91
Auto Specify Sender Name, 55
Auto Tray Switching, 75
B
Background Numbering, 87
Back Margin: Left / Right, 82
Back Margin: Top / Bottom, 82
Bidirectional Communication, 52
Blank Page Print, 171
Box Settings, 150
Bypass Tray Setting Priority, 171
Downloaded from ManualsPrinter.com Manuals
Capture Server IP Address, 55
Centre Mark, 99
Change Initial Mode, 75, 95, 179
Change PDF Password, 178
Changing the Display Language, 261
Channel, 53
Checkered Mark, 99
Communication Mode, 53
Compression (Black & White), 183
Compression (Gray Scale / Full Colour), 183
Config. Page, 167
Copier/Document Server Auto Reset
Timer, 47
Copier / Document Server Features /
Edit, 82
Copier / Document Server Features /
General Features, 75
Copier / Document Server Features /
Input/Output, 91
Copier / Document Server Features /
Reproduction Ratio, 80
Copier / Document Server Features /
Stamp, 87
Copies, 171
Copy Count Display, 41
Copy Function Key: F1-F5, 75
Copy on Designating Page in Combine, 82
Copy on Designating Paper, 82
Copy Order in Combine, 82
Copy Orientation in Duplex Mode, 75
Copy Quality, 75
Counter, 263
Courier Font, 175
Cover Sheet Tray, 44
D
Data Format, 177
Date Stamp, 89
DDNS Configuration, 49
Default Printer Language, 171
Default Scan Settings, 179
Default User Name / Password (Send), 55
Delete All Files in Document Server, 62
Delete All Logs, 62
Delete All Stored Print Jobs, 170
Delete All Temporary Print Jobs, 170
Delete Scanner Journal, 183
Deleting a Special Sender, 149
Delivery Option, 55
279
Density (Background Numbering), 87
Destination List Display Priority 1, 182
Destination List Display Priority 2, 182
Destination List Settings / Scanner
Features, 182
Display / Clear / Print Counter per User
Code, 62
Display Panel, 2
Display / Print Counter, 62
Divide & Send E-mail, 183
DNS Configuration, 49
Document Server, 93
Document Server Storage Key: F1-F5, 75
Domain Name, 49
Double Copies Separation Line, 82
Duplex, 171
Duplex Back Page Stamping Position
(Page Numbering), 90
Duplex Mode Priority, 75
File Transfer / System Settings, 55
File Type Priority, 183
Firmware Version, 62
Font (Date Stamp), 89
Font Number, 175
Font (Page Numbering), 90
Font Pitch, 175
Font Source, 175
Format (Date Stamp), 89
Form Lines, 175
Forwarding, 99, 139
Forwarding Mark, 128
Front Cover Copy in Combine, 82
Front Margin: Left / Right, 82
Front Margin: Top / Bottom, 82
Function Priority, 41
Function Reset Timer, 41
G
Gateway Address, 49
General Features / Copier / Document
Server Features, 75
General Settings/Adjustment / Facsimile
Features, 95
General Settings / System Settings, 41
E
Edge Smoothing, 171
Edge to Edge Print, 171
Edit / Copier / Document Server
Features, 82
Effective Protocol, 49
E-mail Communication Port, 55
E-mail Information Language, 183
E-mail Reception Interval, 55
E-mail Settings / Facsimile Features, 101
E-mail Storage in Server, 55
Enable H.323, 103, 107
Enable SIP, 103, 107
Enlarge 1-5, 80
Erase Border Width, 82
Erase Centre Width, 82
Erase Original Shadow in Combine, 82
Error Log, 167
Ethernet Speed, 49
Extend A4 Width, 175
Extended Security, 62
F
Facsimile Auto Reset Timer, 47
Facsimile Features / Administrator
Tools, 107
Facsimile Features / E-mail Settings, 101
Facsimile Features / General Settings/
Adjustment, 95
Facsimile Features / IP-Fax Settings, 103
Facsimile Features / Reception Settings, 99
Fax E-mail Account, 55
Fax RX File Transmission, 55
280
Downloaded from ManualsPrinter.com Manuals
H
H.323 Settings, 103, 107
Hex Dump, 167
Host Interface / Printer Features, 174
Host Name, 49
I
IEEE 802.11b, 53
Image Density, 75
Image Repeat Separation Line, 82
Initial Print Job List, 171
Input/Output / Copier / Document
Server Features, 91
Input Prime, 52
Inquiry, 262
Interface Settings / System Settings, 49
Internet Fax Settings, 101, 107
I/O Buffer, 174
I/O Timeout, 174
IP Address, 49
IP-Fax Settings / Facsimile Features, 103
J
Job End Call, 75
Job Separation, 171
K
Key Counter Management, 62
L
LAN Type, 49
Letterhead Setting, 91, 171
Line Priority Setting, 95
List / Test Print Lock, 170
List / Test Print / Printer Features, 167
M
Machine Name, 49
Maintenance / Printer Features, 170
Max. Copy Quantity, 75
Max. E-mail Size, 101, 183
Max. Reception E-mail Size, 55
Memory Full Auto Scan Restart, 91
Memory / Immed. Transmission Switch, 95
Memory Lock, 140
Memory Overflow, 171
Memory Usage, 171
Menu List, 167
Mixed Original Sizes Priority, 179
Multiple Lists, 167
N
NCP Delivery Protocol, 49
Network, 49
Network Security Level, 62
Number of Scanner Recalls, 55
NW Frame Type, 49
O
On Hook Mode Release Time, 95
Orientation, 175
Orientation: Booklet, Magazine, 82
Original Orientation in Duplex Mode, 75
Original Orientation Priority, 179
Original Setting, 179
Original Type Display, 75
Original Type Priority, 75, 95
Output: Copier, 41
Output: Document Server, 41
Output: Facsimile, 41
Output: Printer, 41
Output tray settings, 43
Downloaded from ManualsPrinter.com Manuals
P
Page Numbering, 90
Page Numbering in Combine (Page
Numbering), 90
Page Numbering Initial Letter, 90
Page Size, 171
Panel Off Timer, 47
Panel Tone, 41
Paper Display, 75
Paper Tray, 99, 140
Paper Tray Priority: Copier, 44
Paper Tray Priority: Facsimile, 44
Paper Tray Priority: Printer, 44
Paper type
LCT, 45
Paper Type: Bypass Tray, 44
Paper Type: Tray 1-4, 44
Parallel Communication Speed, 52
Parallel Interface, 52
Parallel Timing, 52
Parameter Setting, 107
Parameter Setting: Print List, 107
PCL Config./Font Page, 167
PCL Menu / Printer Features, 175
PDF Config./Font Page, 167
PDF Group Password, 178
PDF Menu / Printer Features, 178
Permit SNMPv3 Communication, 49
Permit SSL/TLS Communication, 49
Ping Command, 49
Point Size, 175
POP3 / IMAP4 Settings, 55
POP before SMTP, 55
Preset Stamp, 87
Print Address Book: Destination List, 62
Print & Delete Scanner Journal, 183
Printer Auto Reset Timer, 47
Printer Bypass Paper Size, 44
Printer Features / Host Interface, 174
Printer Features / List / Test Print, 167
Printer Features / Maintenance, 170
Printer Features / PCL Menu, 175
Printer Features / PDF Menu, 178
Printer Features / PS Menu, 177
Printer Features / System, 171
Printer Language, 171
Print Error Report, 171
Printing the Special Sender List, 149
Print List, 54
Print Priority, 41
Print Reception Time, 99
281
Print Scanner Journal, 183
Priority Setting: Enlarge, 80
Priority Setting: Reduce, 80
Program / Change Administrator, 62
Program / Change / Delete E-mail
Message, 55
Program / Change /
Delete Gateway, 103, 107
Program / Change /
Delete LDAP Server, 62
Program / Change / Delete Subject, 55
Program Closed Network Code, 107
Program / Delete Stamp
(User Stamp), 88
Program Economy Time, 95
Program Fax Information, 95, 107
Program Memory Lock ID, 107
Programming Authorized RX and Special
RX Function, 147
Programming Bypass Tray Paper Size, 147
Programming/Changing Special
Senders, 141
Programming Initial Set Up of a Special
Sender, 146
PS Config./Font Page, 167
PS Menu / Printer Features, 177
Q
Quick Operation Key, 95
R
Ratio for Create Margin, 80
Reception File Print Quantity, 139
Reception Protocol, 55
Reception Settings / Facsimile Features, 99
Reduce 1-6, 80
Reduce Recovery Time, 62
Registering Fax Information, 115
R/E Priority, 80
Reproduction Ratio / Copier / Document
Server Features, 80
Resolution, 175, 177, 178
Return to Defaults, 53
Rotate Sort: Auto Paper Continue, 91
RX File Print Qty (Reception File Print
Quantity), 99
RX Reverse Printing (Reception Reverse
Printing), 99
282
Downloaded from ManualsPrinter.com Manuals
S
SADF Auto Reset, 91
Scan End Reset, 95
Scanner Auto Reset Timer, 47
Scanner Features / Destination List
Settings, 182
Scanner Features / Send Settings, 183
Scanner Recall Interval Time, 55
Scan Settings / General Settings, 179
Scan Settings / Scanner Features, 179
Select Dial / Push Phone, 107
Selection Signal Status, 52
select punch type, 91
Select Stack Function, 91
select stapling position, 91
Select Title, 95, 182
Send Settings / Scanner Features, 183
Separation Line in Combine, 82
Set Date, 47
Set Time, 47
Setup IEEE 802.11b, 10
Setup Wireless LAN, 10
Shortcut R / E, 80
Signal Control, 52
SIP Settings, 103, 107
Size (Background Numbering), 87
Size (Date Stamp), 89
Size (Page Numbering), 90
Size Setting, 41
Slip Sheet Tray, 44
SMB Computer Name, 49
SMB Work Group, 49
SMTP Authentication, 55
SMTP RX File Delivery Settings, 101
SMTP Server, 55
Specify Tray for Lines, 99
SSID Setting, 53
Stamp / Copier / Document Server
Features, 87
Stamp Format 1-4 (User Stamp), 88
Stamp Format (Page Numbering), 90
Stamp Format (Preset Stamp), 87
Stamp Language (Preset Stamp), 87
Stamp on Designating Slip Sheet (Page
Numbering), 90
Stamp Position 1-4 (User Stamp), 88
Stamp Position (Date Stamp), 89
Stamp Position (Page Numbering), 90
Stamp Position (Preset Stamp), 87
Stamp Priority (Preset Stamp), 87
Stamp Setting (Date Stamp), 89
Stored File E-mail Method, 183
Store File Priority, 183
Sub Paper Size, 171
Superimpose (Date Stamp), 89
Superimpose (Page Numbering), 90
Switch Reception Mode, 99
Switch to Batch, 91, 179
Symbol Set, 175
System Auto Reset Timer, 47
System / Printer Features, 171
System Settings / Administrator Tools, 62
System Settings / File Transfer, 55
System Settings / General Features, 41
System Settings / Timer Settings, 47
System Settings / Tray Paper Settings, 44
T
U
Unauthorized Copy Control, 62
Update Delivery Server Destination List, 182
Use LDAP Server, 62
User Authentication management, 62
User Stamp, 88
W
Wait Time for Next Orig.:
Exposure Glass, 179
Wait Time for Next Original(s):
SADF, 179
Warm Up Notice, 41
WEP (Encryption) Setting, 53
WINS Configuration, 49
Wireless LAN Signal, 53
Text Size Priority, 95
Timer Settings / System Settings, 47
Tone: Original Remains, 75
Toner Saving, 171
Transfer Log Setting, 62
Transmission Speed, 53
Tray Paper Settings / System Settings, 44
Tray Paper Size: Tray 1-4, 44
Tray Switching, 171
TWAIN Standby Time, 183
TX Stamp Priority, 95
Downloaded from ManualsPrinter.com Manuals
283
284
Downloaded from ManualsPrinter.com Manuals
GB
GB
B297-6900
Declaration of Conformity
“The Product complies with the requirements of the EMC Directive 89/336/EEC and its amending directives and the Low Voltage Directive 73/23/EEC and its amending directives.”
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
a means POWER ON.
c means STAND BY.
Trademarks
Microsoft®, Windows® and Windows NT® are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
Acrobat® is a registered trademark of Adobe Systems Incorporated.
NetWare is a registered trademark of Novell, Inc.
Other product names used herein are for identification purposes only and might be trademarks of their
respective companies. We disclaim any and all rights to those marks.
The proper names of the Windows operating systems are as follows:
The product name of Windows® 95 is Microsoft® Windows® 95
The product name of Windows® 98 is Microsoft® Windows® 98
The product name of Windows® Me is Microsoft® Windows® Millennium Edition (Windows Me)
The product names of Windows® 2000 are as follows:
Microsoft® Windows® 2000 Advanced Server
Microsoft® Windows® 2000 Server
Microsoft® Windows® 2000 Professional
The product names of Windows® XP are as follows:
Microsoft® Windows® XP Professional
Microsoft® Windows® XP Home Edition
The product names of Windows Server™ 2003 are as follows:
Microsoft® Windows Server™ 2003 Standard Edition
Microsoft® Windows Server™ 2003 Enterprise Edition
Microsoft® Windows Server™ 2003 Web Edition
The product names of Windows® NT are as follows:
Microsoft® Windows NT® Server 4.0
Microsoft® Windows NT® Workstation 4.0
Copyright © 2006
Downloaded from ManualsPrinter.com Manuals
Operating Instructions General Settings Guide
GB GB
B297-6900
Downloaded from ManualsPrinter.com Manuals
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising