Model 2015-61 Upconverter Instruction Manual

Model 2015-61 Upconverter Instruction Manual
Model 2015-61
Instruction Manual
Upconverter
November 2009 Rev. A
IF MONITOR
RF MONITOR
MODEL 2015
F = 5950.000 AUTO
G = +20.00
EXT
UPCONVERTER
MENU
CROSS TECHNOLOGIES INC.
EXECUTE
REMOTE POWER
MUTE
ALARM
Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., but may be
reproduced or duplicated without the prior permission of Cross Technologies, Inc. for purposes of operating
the equipment.
When ordering parts from Cross Technologies, Inc., be sure to include the equipment model number,
equipment serial number, and a description of the part.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL info@crosstechnologies.com
INSTRUCTION MANUAL
MODEL 2015-61 Upconverter
TABLE OF CONTENTS
PAGE
Warranty
1.0 General
1.1 Equipment Description
1.2 Technical Characteristics
1.3 Monitor & Control Interface
2.0 Installation
2.1 Mechanical
2.2 Rear Inputs & Outputs
2.3 Front Panel Controls & Indicators
2.4 Operation
2.5 Menu Settings
2
3
3
4
5
7
7
8
8
9
10
WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.
All Cross Technologies, Inc. products are warranted against defective materials and
workmanship for a period of one year after shipment to customer. Cross Technologies, Inc.’s
obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s option,
replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall not be
liable for any special, indirect, or consequential damages. This warranty does not cover parts
or equipment which have been subject to misuse, negligence, or accident by the customer
during use. All shipping costs for warranty repairs will be prepaid by the customer. There are
not other warranties, express or implied, except as stated herein.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL info@crosstechnologies.com
2015-61 Manual, Rev. A
Page 2
11/12/09
MODEL 2015-61 Upconverter
1.0 General
1.1 Equipment Description
The 2015-61 Upconverter converts 70 ± 18 MHz to 5.85 to 6.425 GHz in 1kHz, 10kHz, 100kHz, or 125kHz
steps (user selectable) with low group delay and flat frequency response. Push button switches select the RF
frequency, gain, and other parameters. Front panel connectors provide -20 dB monitors of the IF and RF
signals. Front panel LEDs provide indication of DC power (green), remote operation (yellow), PLL alarm (red),
or the TX carrier is muted (yellow). Variable attenuators for the IF input and RF output provide a gain range of
+10 to +30 dB as adjusted by the front panel pushbutton switches. Remote operation allows selection of
frequency and gain. Parameter selection and frequency, gain and 10MHz reference source settings appear on
the LCD display. Connectors are BNC for IF input, IF monitor, and 10MHz reference input and output, and
Type N for the RF output and SMA for the RF monitor. The 2015-61 is powered by a 100-240 ±10% VAC
power supply; and housed in a 1.75” X 19 “ X 16” rack mount chassis. The unit is powered by a 100-240
±10% VAC power supply, and housed in a 1.75" X 19" X 16" 1RU chassis.
IF MONITOR
RF MONITOR
MODEL 2015
F = 5950.000 AUTO
G = +20.00
EXT
UPCONVERTER
MENU
CROSS TECHNOLOGIES INC.
EXECUTE
REMOTE POWER
MUTE
ALARM
FRONT
AC
10 MHZ REF
OUTPUT
GND
MONITOR
AND
CONTROL
RF OUT
10 MHZ
EXT REF
INPUT
IF IN
J3
J4
5 4 3 2
1
9 8 7 6
J18
J10
J5
REAR
FIGURE 1.1 Model 2015-61 Front and Rear Panels
RF
MON
-20 dB
70
MHz
IN
VAR
ATT
VAR
ATT
-20 dB
IF
MON
F=5950.000 AUTO
G=+20.00
EXT
5.85
to
6.425
GHz
EXT OUT
10 MHz
CONTROLLER
INT
10 MHz
FIGURE 1.2 Model 2015-61 Upconverter Block Diagram
2015-61 Manual, Rev. A
Page 3
11/12/09
1.2 Technical Characteristics
TABLE 1.1 2015-61 Upconverter Specifications*
Input Characteristics (IF)
Impedance
Return Loss
Frequency
Level
50
18 dB
70 ± 18 MHZ
-40 to -20 dBm
Output Characteristics (RF)
Impedance
50
Return Loss
14 dB
Frequency
5.85 to 6.425 GHz
Level
-20 to 0 dBm
1dB compression
+9 dBm
Carrier Mute
-60 dBc
Channel Characteristics
Gain range
Spurious Response
Intermodulation
Frequency Response
AM/PM Conversion:
Gain Stability
Gain Slope
Group Delay, max
Frequency Sense
+10 to +30 dB (adjustable in 0.25 dB steps)
< -55dBC @ 0dBm output
<-38 dBc for two carriers each at 0 dBm output
±1.5 dB, 5.85-6.425 GHz ; ± 0.5 dB, 36 MHz BW
0.1 deg/dB max @ -5 dBm output
± 0.25 dB/day
0.1 dB/MHz
0.01 ns/MHz2, parabolic, 0.03 ns/MHz, linear, 1 ns ripple peak-to-peak
Non-inverting
Synthesizer Characteristics
Frequency Accuracy
±0.01 ppm internal reference; Auto locks to external reference at 0 ± 3 dBm input
Frequency Step
1kHz, 10kHz, 100kHz, 125kHz (selectable)
10 MHz In/Out Level
3 dBm ± 3 dB
Phase Noise @ Freq
dBC/Hz
100 Hz
1kHz
10kHz
100kHz
1MHz
-65
-75
-85
-95
-105
Controls, Indicators
Freq/Gain Selection
Power
Alarm
Mute
Remote
Remote
Monitors (-20±2dB)
direct readout LCD; pushbutton switches or remote selection
Green LED
Red LED
Yellow LED
Yellow LED
RS232C, 9600 baud
IF: -20dB of input, 50 BNC, female / RF: -20dB of output, 50 SMA, female
Other
RF / RF Mon Connector
IF / IF Mon Connector
10 MHz Connectors
Alarm/Remote Conn.
Size
Power
Type N (female) / SMA (female)
BNC (female) / BNC (female)
BNC (female), 75; works for 50 or 75 ohm impedance
DB9 - NO or NC contact closure on Alarm
19 inch, 1RU standard chassis 1.75”high X 16.0” deep
100-240 ±10% VAC, 47-63 Hz, 45 watts max
Options
Q
RS485 Remote Interface
*+0˚C to +50˚C; Specifications subject to change without notice
2015-61 Manual, Rev. A
Page 4
11/12/09
1.3 Monitor and Control Interface
A) Remote Serial Interface
Protocol: RS-232C, 9600 baud rate, no parity, 8 data bits, 1 start bit, and 1 stop bit.
(RS-232C, RS-422, or RS-485 - option -Q)
M&C Cable Diagram - Cross Technologies Frequency Converters
Male DB-9
2015/16/17 M&C Port
Female DB-9
PC Com Port
1
1
RX
RX
3
TX
TX
4
DTR
5
SG
6
DSR
6
RTS
7
2
7
3
4
SG
CTS
8
2
5
8
9
9
Connector - Rear panel, DB-9 female
Pinouts (RS-485/422/232C)
Pin
Description
1
Rx-
2
Rx+ (RS-232C)
3
Tx+ (RS-232C)
4
Tx-
5
Ground
6
Alarm Relay - Common
7
Alarm Relay - Normally Open
8
Not Used
9
Alarm Relay - Normally Closed
2015-61 Manual, Rev. A
Page 5
11/12/09
B) Status Requests Table 13 lists the status requests for the 2015-02 and briefly describes them.
*
PLEASE NOTE: The two character {aa}(00-31) prefix, in the table below,
should be used ONLY when RS-485, (OPTION-Q), is selected.
Table 1.3 2015-61 Status Requests
Req
quests
Command
Syntax
Description
Command Status
{aaS1}*
Returns {aaS1bbbbbbbccddddEFAM} where:
• bbbbbbb = Tx frequency
• cc = Input Level
• dddd = Tx Gain
• E = 10MHz Ref Status (0 = Internal, 1 = External)
• F = 10MHz Ref Mode (0=Internal, 1=External, 2=Auto
• A = Alarm Status (0 = NO Alarm, 1 = Alarm)
• M = Tx RF Status (1 = Normal, 0 = Muted)
2015-61 Manual, Rev. A
Page 6
11/12/09
C) Commands Table 1.2 lists the commands for the 2015-60 and briefly describes them. After a command is sent the 2015-60
sends a return “>” indicating the command has been received and executed.
General Command Format - The general command format is {aaCND...}, where:
{ = start byte
aa = Address (RS-485 only)
C = 1 character, either C (command) or S (status)
N = 1 character command or status request
D = 1 character or more of data (depends on command)
} = stop byte
*
PLEASE NOTE: The two character {aa}(00-31) prefix, in the table below,
should be used ONLY when RS-485, (OPTION-Q), is selected.
Table 1.2 2015-61 Commands
Command
ds
Command
Syntax
Description
Set Transmitter Frequency
{aaC1xxxxxxx}*
where:
• xxxxxxx = 7 characters
• Range: 5850000 to 6425000 kHz, 1kHz steps min.
Set Input Level
{aaCIxx}*
where:
• xx = 2 characters
• Range: 20 to 40 (-20 dB to -40 dB, in 1 dB steps)
Set Transmit Gain
{aaC3xxxx}*
where:
• xxxx = 4 characters
• Range: 1000 to 3000 (10.00 to 30.00 dB, 0.25 dB steps)
Enable Tx
{aaCAx}*
where x =:
• 0 to disable Tx signal
• 1 to enable Tx signal
External 10MHz Mode
{aaCEx}*
where x =:
• 0 = Internal 10MHz ref signal
• 1 = External 10MHz ref signal
• 2 = Auto 10MHz ref signal
Enable Remote
#
Just # sign
Disable Remote
{aaCR0}*
{CR and zero}
2015-61 Manual, Rev. A
Page 7
11/12/09
2.0 Installation
2.1 Mechanical - The 2015-61 consists of one RF/Controller PCB, RF components and synthesizer assembly
housed in a 1 RU (1 3/4 inch high) by 16 inch deep chassis. A switching, ± 12, +24, +5 VDC power supply
provides power for the assembly. The 2015-61 can be secured to a rack using the 4 holes on the front panel.
Figure 2.1 shows how the 2015-61 is assembled.
FIGURE 2.1 2015-61 Mechanical Assembly
2015-61 Manual, Rev. A
Page 8
11/12/09
2.2 Rear Panel Input / Output Signals - Figure 2.2 shows the input and output connectors on the rear panel.
J18 - 10 MHz REF OUTPUT
10 MHz reference output,
3 ± 3 dBm, 50/75 ohms
BNC (female) connector.
J10 - MONITOR AND CONTROL
DB9 female connector. see Table
2.1.
J3 - 10 MHz EXT REF INPUT
10 MHz external reference input,
3 ± 3 dBm, 50/75 ohms,
BNC (female) connector.
AC
GND
MONITOR
AND
CONTROL
10 MHZ REF
OUTPUT
5
4
9
3
8
2
7
RF OUT
10 MHZ
EXT REF
INPUT
IF IN
J3
J4
1
6
J5
J10
J18
AC - POWER IN
AC input for switching power supply.
100-240 ±10% VAC, 47-60 Hz.
J4 - IF IN
70 MHz IF input
-40 to -20 dBm
BNC (female) connector
J5 - RF OUT
5850-6425 MHz RF output
-20 to 0 dBm
Type N (female) connector
FIGURE 2.2 2015-61 Rear Panel Inputs and Outputs
Table 2.1 J10 Pinouts (RS-485/RS-422/RS-232C)*
Pin
Description
1
Rx-
2
Rx+ (RS-232C)
3
Tx+ (RS-232C)
4
Tx-
5
Ground
6
Alarm Relay - Common
7
Alarm Relay - Normally Open
8
Not Used
9
Alarm Relay - Normally Closed
*Interface: DB-9 Female; Protocol: RS-485, RS-422, or RS-232C (selectable), 9600 baud rate, no
parity, 8 data bits, 1 start bit, 1 stop bit
2.3 Front Panel Controls and Indicators -The following are the front panel controls and indicators.
IF MONITOR
-20dB monitor of the
IF input
IF MONITOR
RF MONITOR
-20dB monitor of the
RF output
DS6 - POWER LED
Green LED indicates
presence of DC power.
LCD DISPLAY
Display shows Frequency in MHz and
Gain in dB. Is used during Program
Mode to change settings.
S1 - MENU/EXECUTE BUTTON
Press this to get into Program mode
and to execute any changes.
RF MONITOR
F = 5950.000 AUTO
G = +20.00
EXT
MENU
EXECUTE
REMOTE
POWER
MUTE
DS5 - UP MUTE LED
Red LED indicates
upconverter mute.
DS1 - REMOTE LED
Yellow LED indicates
remote operation.
ALARM
DS2 - UP ALARM LED
Red LED indicates
upconverter alarm.
S2 - VERT. TOGGLE
S3 - HORIZ. TOGGLE
Vertical toggle switch that controls
Horizontal toggle switch that
values in the Menu items when in
controls which values are being
program mode. Does not function in the adjusted. Does not function in the
normal display mode
normal display mode
FIGURE 2.3 2015-61 Front Panel Controls and Indicators
2015-61 Manual, Rev. A
Page 9
11/12/09
2.4 Installation / Operation
2.4.1 Installing and Operating the 2015-61 Upconverter
1. Connect a -40 dBm to -20 dBm, 70MHz signal to IF IN, J4 (Figure 2.2)
2. Connect the RF OUT, J5, to the external equipment.
3. Connect 100-240 ±10% VAC, 47 - 63 Hz to AC input on the back panel.
4. Select 10 MHz Reference Mode EXT, INT, AUTO (automatically locks to external reference at 0 ± 3
dBm in) (See Section 2.5 Menu Settings).
5. Set the desired output frequency (See Section 2.5 Menu Settings).
6. Set the input level (See Section 2.5 Menu Settings).
7. Set the gain for +10 to +30 dB. Make sure the output stays within -20 to 0 dBm with the gain selected
and the input level provided. The firmware will prevent setting gain and input level outside this range.
(See Section 2.5 Menu Settings).
8. Set the 10 MHz reference operating mode as desired for AUTO, EXTernal, or INTernal (See Section
2.5 Menu Settings).
9. Be sure DS6 (green, DC Power) is on and DS2 (red, Alarm) is off (Figure 2.3).
10. AC Fuse - The fuse is a 5 mm X 20 mm, 2 amp slow blow (Type T) and is inserted in the far slot in the
drawer below the AC input as shown in Figure 2.4. There is a spare fuse in the near slot. If a fuse
continues to open, the power supply is most likely defective.
FUSE DRAWER
SPARE FUSE DRAWER
AC Fuse - 2 amp slow blow (Type T 2A GDC),
5 mm X 20 mm
INPUT
~
100-240± 10%VAC
47-63 Hz
2A MAX
FUSE
TYPE T 2A GDC
250 VOLT
FOR 100 - 240 V~
FIGURE 2.4 Fuse Location and Spare Fuse
2015-61 Manual, Rev. A
Page 10
11/12/09
2.5 Menu Settings
2.5.1 Functions - This section describes operation of the front panel controls. There are three operator
switches, the LCD display and alarm indicator LEDs. All functions for the equipment are controlled by these
components. The functions are (see Figure 2.5):
Power Up
Normal Display
Menu 1
Menu 2
Menu 3
Menu 4
Menu 5
Menu 6
Menu 7
Menu 8
Menu 9
Frequency in MHz
Input Level in dBm (-40 to -20)
Gain in dB (0 to +20)
Mute TX Signal
Set Unit to Remote Operation
Select Frequency Step Size (1kHz, 10kHz, 100kHz, or 125kHz)
Select Reference Mode EXT, INT, AUTO (locks to external reference at 0 ± 3 dBm in)
Select RS232, RS422, or RS485 Remote Operation (option Q)
Select RS485 Remote Address for Unit (option Q)
Save Menu
When go to end
Alarm indications appear on the LEDs (see figure 2.2).
All program changes must start with the operation of the Menu/Execute switch and must also end with the
operation of the Menu/Execute switch verified by the “Save Settings?” Menu. If this sequence is not followed,
none of the changes will take effect. If programming is initiated and no operator action takes place for
approximately 12 seconds (before the final press of the Menu/Execute switch) the display will revert to its
previous status and you will need to start over.
2015-61 Manual, Rev. A
Page 11
11/12/09
2.5.2. Power On Settings
NOTE: The last status of a unit is retained even when power is removed. When power is restored, the unit
will return to it's previous settings.
When power is first applied, the LCD display goes through three steps.
1.The LCD goes black to show all segments are functioning.
2.The software version will be displayed.
REV 1.00
3.The present frequency, gain, and selected 10 MHz Reference mode of the upconverter is shown.
F = 5950.000
G = +10.00
INT
The unit is now operational and ready for any changes the operator may desire.
2.5.3 Control Switches
1. Menu/Execute - Any change to the programming of the unit must be initiated by pressing the
Menu/Execute switch and completed by pressing the Menu/Execute switch.
2. Horizontal Switch - This switch is mounted so its movement is horizontal and moves the cursor left or
right.
3. Vertical Switch - This switch is mounted so its movement is vertical and has two functions:
A) During frequency, gain changes, the vertical movement will raise or lower the number in the
direction of the arrows.
B) For other functions such Mute on/off, the vertical switch will alternately turn the function
on or off regardless of the direction operated.
2015-61 Manual, Rev. A
Page 12
11/12/09
2.5.4 Frequency Changes
At any time during the modification process, if you have made a mistake and do not wish to save the changes
you have made, do not press the Menu/Execute switch; simply do nothing for approximately 12 seconds,
and the system will return to the normal operating mode or scroll to “R” and push the menu/Execute switch
and select “NO” in the “SAVE SETTINGS?” window.
To change the FREQUENCY:
1.Operate the Menu/Execute switch until you get to the menu item you want to change see Figure 2.5 for
the sequence of menu options. The following display is for changing the upconverter frequency:
F = 5950.000
R
Pressing the Up/Down switch down will toggle the display to:
F = 5850.000
R
By using the horizontal rocker switch the cursor can be moved left or right .
F = 5850.000
R
NOTE: STEP SIZE IS FACTORY SET TO 1 KHZ STEPS SO YOU CAN ADJUST 1, 10, 0R 100 KHZ
BY SCROLLING TO THAT DIGIT. THE UNIT WILL ONLY INCREMENT AS LOW AS THE STEP
IT IS SET TO INCREMENT IN.
NOTE: CHANGES DO NOT TAKE PLACE ON FREQUENCY UNTIL YOU GO TO THE SAVE
MENU AND INDICATE YOU WANT TO SAVE THE CHANGES. THE CARRIER IS MUTED
WHEN FREQUENCY IS CHANGED.
When the display indicates the value desired you can push the Menu/Execute switch to the next item:
INLVL = -20
R
OR you can scroll to “R”, push the Menu/Execute switch to get to:
SAVE SETTINGS?
Y N
Selecting Y will save the new settings. Selecting N will revert to the previous settings.
Pushing the Menu/Execute switch then takes you to the default display:
F = 5950.000
G = +10.00
INT
Figure 2.5 shows all the menu items and how to make changes.
2015-61 Manual, Rev. A
Page 13
11/12/09
2.5.5 Gain Changes
When you get to this menu note that the gain changes will be made as you make them but if you do not wish to
save the changes you have made, scroll to “R” and push the menu/Execute switch and select “NO” in the
“SAVE SETTINGS?” window or do not press the Menu/Execute switch; simply do nothing for
approximately 12 seconds, and the system will return to the normal operating mode.
To change the GAIN, first push the Menu/Execute switch to get to the gain setting:
Operate the Menu/Execute switch until you get to the menu item you want to change (see Figure 2.5 for
the sequence of menu options). The following display is for changing the upconverter input level. This
is an important setting to optimize spurious and should be made as accurately as possible:
INLVL = -20
R
NOTE: CHANGES TAKE PLACE ON LEVEL AND GAIN IMMEDIATELY BUT DO NOT GET
SAVED UNTIL YOU GO TO THE SAVE MENU AND INDICATE YOU WANT TO SAVE THE
CHANGES.
Press the Up/Down switch to change the level in 1 dB steps and then push the Menu/Execute switch to
get to the Gain setting:
G = +10.00
R
Press the Up/Down switch to change the gain in 0.25, 1 or 10 dB steps:
G = +20.00
R
By using the horizontal rocker switch the cursor can be moved left or right. Pressing the Up/Down
switch down will toggle the display digit selected until you have the desired gain.
NOTE: THE GAIN WILL BE CHANGED AS YOU ADJUST THE NUMBERS. HOWEVER, THE
VALUE WILL NOT BE STORED UNTIL YOU INDICATE YES IN THE SAVE SETTINGS
WINDOW. DO NOT SET A GAIN THAT WOULD EXCEED 0 dBm OR HAVE LESS THAN -20 dBm
OUTPUT LEVEL. THE FIRMWARE PREVENTS YOU FROM THIS.
When the display indicates the value desired you can push the Menu/Execute switch to the next item
OR you can scroll to “R”, push the Menu/Execute switch to get to:
SAVE SETTINGS?
Y N
Selecting Y will save the new settings. Selecting N will revert to the previous settings.
Pushing the Menu/Execute switch then takes you to:
F = 5850.000
G = +20.00
INT
Figure 2.5 gives the menu items and how to make changes
2015-61 Manual, Rev. A
Page 14
11/12/09
2.5.6 10 MHz Reference Mode Changes
At any time during the modification process, if you have made a mistake and do not wish to save the changes
you have made, do not press the Menu/Execute switch; simply do nothing for approximately 12 seconds,
and the system will return to the normal operating mode or scroll to “R” and push the menu/Execute switch
and select “NO” in the “SAVE SETTINGS?” window.
To change the 10 MHZ REF:
1.Operate the Menu/Execute switch until you get to the menu item you want to change see Figure 2.5 for
the sequence of menu options. The following display is for changing the 10 MHz Reference Mode:
REF MODE = INT
R
Pressing the Up/Down switch down will toggle the display to:
REF MODE = AUTO
R
By using the horizontal rocker switch the cursor can be moved left or right .
REF MODE = EXT
R
NOTE: CHANGES DO NOT TAKE PLACE ON FREQUENCY UNTIL YOU GO TO THE SAVE
MENU AND INDICATE YOU WANT TO SAVE THE CHANGES. THE CARRIER IS MUTED
WHEN REFERENCE IS CHANGED IF PLL LOCK IS IN ALARM.
When the display indicates the value desired you can push the Menu/Execute switch to the next item:
OR you can scroll to “R”, push the Menu/Execute switch to get to:
SAVE SETTINGS?
Y N
Selecting Y will save the new settings. Selecting N will revert to the previous settings.
Pushing the Menu/Execute switch then takes you to the default display:
F = 5950.000
G = +10.00
INT
If you have selected AUTO, the display will show AUTO and whether you have INT or EXT
automatically selected.
F = 5950.000
AUTO
G = +10.00
INT
Figure 2.5 shows all the menu items and how to make changes.
2015-61 Manual, Rev. A
Page 15
11/12/09
2.5.7 Alarm Indications
An alarm condition will occur if the local oscillator phase lock loop (PLL) comes out of lock. The Mute LED
will light if you select to mute the Tx Signal and the Remote LED will light when you select the Remote mode.
ON POWER UP
REV 1.00
Power Up
NORMAL DISPLAY
F = 5950.000
G = +10.00
Normal Display
AUTO
INT
PUSH BUTTON
PUSHING MENU/EXECUTE SEQUENCE
F = 5950.000
Menu 1 Set Frequency
R
SCROLL <>
SCROLL
Menu 2 Set Input Level (from
-40 to -20)
INLVL = -20
R
Menu 3 Set Gain (+10 to +30)
G = +10.00
Menu 4 Mute TX signal
MUTE
Menu 5 Set Unit to Remote
Operation
REMOTE
Menu 6 Set Frequency Step Size
(1kHz, 10kHz, 100kHz, or 125kHz)
STEP = 1 KHZ
Menu 7 Select External 10 MHz
Reference Mode
REF MODE = AUTO
R
Menu 8 Set Remote Mode
(option -Q)
RS485
R
Menu 9 Set RS-485 Address
(option -Q)
ADDRESS = 00
R
Menu 10 View PCB Temperature
(option -T)
TEMP = 35 DEG
R
Save Settings? At the end or
when “R” is selected from any of
the above menus
SAVE SETTINGS?
SCROLL <>
SCROLL
R
R
R
PUSH BUTTON
SCROLL <>
SCROLL
R
PUSH BUTTON
SCROLL <>
SCROLL
OFF
PUSH BUTTON
SCROLL <>
SCROLL
OFF
PUSH BUTTON
PUSH BUTTON
SCROLL <>
SCROLL
PUSH BUTTON
SCROLL <>
SCROLL
PUSH BUTTON
SCROLL <>
SCROLL
PUSH BUTTON
SCROLL <>
Y N
SCROLL
PUSH BUTTON
BUTTON
PUSH
SCROLL <>
PUSH BUTTON
SCROLL <>
PUSH BUTTON
FIGURE 2.5 Menu Display and Sequence
2015-61 Manual, Rev. A
Page 16
11/12/09
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL info@crosstechnologies.com
Printed in USA
2015-61 Manual, Rev. A
Page 17
11/12/09
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising