AOT20C60P/AOB20C60P 600V,20A N-Channel MOSFET General Description Product Summary

AOT20C60P/AOB20C60P 600V,20A N-Channel MOSFET General Description Product Summary
AOT20C60P/AOB20C60P
600V,20A N-Channel MOSFET
General Description
Product Summary
• Trench Power AlphaMOS-II technology
• Low RDS(ON)
• Low Ciss and Crss
• High Current Capability
VDS @ Tj,max
700V
IDM
80A
RDS(ON),max
< 0.26Ω
Qg,typ
52nC
Eoss @ 400V
8.2µJ
Applications
100% UIS Tested
100% Rg Tested
• General Lighting for LED and CCFL
• AC/DC Power supplies for Industrial, Consumer, and
Telecom
TO-263
D2PAK
D
TO-220
G
D
D
S
AOT20C60P
S
G
G
S
AOB20B60P
Orderable Part Number
Package Type
Form
Minimum Order Quantity
AOT20C60PL
AOB20C60PL
TO-220 Green
TO-263 Green
Tube
Tape & Reel
1000
800
Absolute Maximum Ratings TA=25°C unless otherwise noted
Parameter
Drain-Source Voltage
Symbol
VDS
Gate-Source Voltage
Continuous Drain
Current
VGS
TC=25°C
TC=100°C
Pulsed Drain Current C
Avalanche Current C
ID
IDM
L=1mH
Maximum
600
Units
V
±30
V
20
16
A
80
IAR
20
A
Repetitive avalanche energy C
EAR
200
mJ
Single pulsed avalanche energy G
MOSFET dv/dt ruggedness
Peak diode recovery dv/dt
TC=25°C
Power Dissipation B Derate above 25°C
Junction and Storage Temperature Range
Maximum lead temperature for soldering
purpose, 1/8" from case for 5 seconds
EAS
1599
100
20
463
3.7
-55 to 150
mJ
W
W/°C
°C
300
°C
Maximum
Units
Thermal Characteristics
Parameter
Maximum Junction-to-Ambient A,D
Maximum Case-to-sink A
Maximum Junction-to-Case
Rev.2.0: January 2015
dv/dt
PD
TJ, TSTG
TL
Symbol
RθJA
RθCS
RθJC
www.aosmd.com
V/ns
65
°C/W
0.5
0.27
°C/W
°C/W
Page 1 of 6
Electrical Characteristics (TJ=25°C unless otherwise noted)
Symbol
Parameter
Conditions
Min
ID=250µA, VGS=0V, TJ=25°C
600
Typ
Max
Units
STATIC PARAMETERS
BVDSS
Drain-Source Breakdown Voltage
BVDSS
/∆TJ
Breakdown Voltage Temperature
Coefficient
IDSS
Zero Gate Voltage Drain Current
ID=250µA, VGS=0V, TJ=150°C
700
ID=250µA, VGS=0V
0.54
VDS=600V, VGS=0V
1
10
Gate-Body leakage current
VDS=0V, VGS=±30V
VDS=5V, ID=250µA
RDS(ON)
VGS=10V, ID=10A
gFS
Forward Transconductance
VDS=40V, ID=10A
20
VSD
Diode Forward Voltage
IS=1A,VGS=0V
0.7
IS
ISM
±100
nA
5
V
0.225
0.26
Ω
1
V
Maximum Body-Diode Continuous Current
20
A
Maximum Body-Diode Pulsed Current C
80
A
Coss
Output Capacitance
Co(er)
Effective output capacitance, energy
related H
Crss
Effective output capacitance, time
related I
Reverse Transfer Capacitance
Rg
Gate resistance
VGS=0V, VDS=100V, f=1MHz
Gate Source Charge
S
3607
pF
140
pF
95
pF
182
pF
3.3
pF
2
Ω
VGS=0V, VDS=0 to 480V, f=1MHz
VGS=0V, VDS=100V, f=1MHz
f=1MHz
SWITCHING PARAMETERS
Qg
Total Gate Charge
Qgs
3
µA
3.8
DYNAMIC PARAMETERS
Input Capacitance
Ciss
Co(tr)
V/ oC
VDS=480V, TJ=125°C
Gate Threshold Voltage
Static Drain-Source On-Resistance
IGSS
VGS(th)
V
52
VGS=10V, VDS=480V, ID=20A
80
nC
20
nC
Qgd
Gate Drain Charge
14
nC
tD(on)
Turn-On DelayTime
77
ns
tr
Turn-On Rise Time
tD(off)
Turn-Off DelayTime
tf
trr
Body Diode Reverse Recovery Time
Qrr
Body Diode Reverse Recovery Charge IF=20A,dI/dt=100A/µs,VDS=100V
VGS=10V, VDS=300V, ID=20A,
RG=25Ω
67
ns
120
ns
43
ns
IF=20A,dI/dt=100A/µs,VDS=100V
599
ns
µC
Turn-Off Fall Time
11
A. The value of R θJA is measured with the device in a still air environment with T A =25°C.
B. The power dissipation PD is based on TJ(MAX)=150°C, using junction-to-case thermal resistance, and is more useful in setting the upper
dissipation limit for cases where additional heatsinking is used.
C. Repetitive rating, pulse width limited by junction temperature TJ(MAX)=150°C, Ratings are based on low frequency and duty cycles to keep
initial TJ =25°C.
D. The R θJA is the sum of the thermal impedance from junction to case R θJC and case to ambient.
E. The static characteristics in Figures 1 to 6 are obtained using <300µs pulses, duty cycle 0.5% max.
F. These curves are based on the junction-to-case thermal impedance which is measured with the device mounted to a large heatsink, assuming
a maximum junction temperature of TJ(MAX)=150°C. The SOA curve provides a single pulse rating.
G. L=60mH, IAS=7.3A, VDD=150V, RG=25Ω, Starting TJ=25°C.
H. Co(er) is a fixed capacitance that gives the same stored energy as Coss while VDS is rising from 0 to 80% V(BR)DSS.
I. Co(tr) is a fixed capacitance that gives the same charging time as Coss while VDS is rising from 0 to 80% V(BR)DSS.
THIS PRODUCT HAS BEEN DESIGNED AND QUALIFIED FOR THE CONSUMER MARKET. APPLICATIONS OR USES AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS ARE NOT AUTHORIZED. AOS DOES NOT ASSUME ANY LIABILITY ARISING
OUT OF SUCH APPLICATIONS OR USES OF ITS PRODUCTS. AOS RESERVES THE RIGHT TO IMPROVE PRODUCT DESIGN,
FUNCTIONS AND RELIABILITY WITHOUT NOTICE.
Rev.2.0: January 2015
www.aosmd.com
Page 2 of 6
TYPICAL ELECTRICAL AND THERMAL CHARACTERISTICS
100
50
VDS=40V
10V
40
7V
10
6.5V
-55°C
ID(A)
ID (A)
30
125°C
6V
20
1
10
25°C
VGS=5.5V
0
0.1
0
5
10
15
20
25
30
2
4
VDS (Volts)
Figure 1: On-Region Characteristics
Normalized On-Resistance
0.4
RDS(ON) (Ω)
8
10
3
0.5
VGS=10V
0.3
0.2
0.1
2.5
2
0
10
20
30
40
1
0.5
0
-100
50
ID (A)
Figure 3: On-Resistance vs. Drain Current and Gate
Voltage
1.2
1E+01
1.1
1E+00
IS (A)
1E+02
0
50
100
150
200
125°C
1E-01
0.9
1E-02
0.8
1E-03
0.7
-100
-50
Temperature (°C)
Figure 4: On-Resistance vs. Junction Temperature
1.3
1
VGS=10V
ID=10A
1.5
0
BVDSS (Normalized)
6
VGS(Volts)
Figure 2: Transfer Characteristics
25°C
1E-04
-50
0
50
100
150
200
TJ (°C)
Figure 5: Break Down vs. Junction Temperature
Rev.2.0: January 2015
www.aosmd.com
0.0
0.2
0.4
0.6
0.8
1.0
VSD (Volts)
Figure 6: Body-Diode Characteristics
Page 3 of 6
TYPICAL ELECTRICAL AND THERMAL CHARACTERISTICS
15
10000
Ciss
VDS=480V
ID=20A
1000
Capacitance (pF)
VGS (Volts)
12
9
6
Coss
100
10
3
0
Crss
1
0
15
30
45
60
75
90
0.1
10
100
1000
VDS (Volts)
Figure 8: Capacitance Characteristics
20
25
16
20
Current rating ID(A)
Eoss(uJ)
Qg (nC)
Figure 7: Gate-Charge Characteristics
1
12
Eoss
8
15
10
4
5
0
0
0
100
200
300
400
500
600
VDS (Volts)
Figure 9: Coss stored Energy
0
25
50
75
100
125
150
TCASE (°C)
Figure 10: Current De-rating (Note F)
100
10
ID (Amps)
10µs
RDS(ON)
limited
100µs
DC
1
1ms
10ms
0.1
TJ(Max)=150°C
TC=25°C
0.01
1
10
100
1000
VDS(Volts)
Figure 11: Maximum Forward Biased Safe Operating
Area for TO-220/TO-263 Green (Note F)
Rev.2.0: January 2015
www.aosmd.com
Page 4 of 6
TYPICAL ELECTRICAL AND THERMAL CHARACTERISTICS
ZθJC Normalized Transient
Thermal Resistance
10
1
D=Ton/T
TJ,PK=TC+PDM.ZθJC.RθJC
RθJC=0.27°C/W
In descending order
D=0.5, 0.3, 0.1, 0.05, 0.02, 0.01, single pulse
0.1
PDM
0.01
Single Pulse
Ton
T
0.001
1E-06
1E-05
0.0001
0.001
0.01
0.1
1
10
100
Pulse Width (s)
Figure 12: Normalized Maximum Transient Thermal Impedance for TO-220/TO-263 Green (Note F)
Rev.2.0: January 2015
www.aosmd.com
Page 5 of 6
Gate Charge Test Circuit & Waveform
Vgs
Qg
10V
+
+ Vds
VDC
-
Qgs
Qgd
VDC
-
DUT
Vgs
Ig
Charge
Resistive Switching Test Circuit & Waveforms
RL
Vds
Vds
Vgs
90%
+ Vdd
DUT
VDC
-
Rg
10%
Vgs
Vgs
td(on)
tr
td(off)
ton
tf
toff
Unclamped Inductive Switching (UIS) Test Circuit & Waveforms
L
2
EAR= 1/2 LIAR
Vds
BVDSS
Vds
Id
+ Vdd
Vgs
Vgs
I AR
VDC
-
Rg
Id
DUT
Vgs
Vgs
Diode Recovery Test Circuit & Waveforms
Q rr = - Idt
Vds +
DUT
Vds -
Isd
Vgs
Ig
Rev.2.0: January 2015
Vgs
L
Isd
+ Vdd
t rr
dI/dt
I RM
Vdd
VDC
-
IF
Vds
www.aosmd.com
Page 6 of 6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising