Man ICR540IN
ICR540IN: Day & Night
Dome Camera
Operation Manual
ICR540IN: Day&Night Dome Camera
Copyright 2007 ICRealtime, Inc. Made in Korea
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
◆ Do NOT use power sources other than those specified.
◆ Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
1
ICR540IN D&N Dome Camera
Features
Warning
Horizontal Resolution of 540 TV
Lines
High Sensitivity
Clear image quality has been achieved by
employing a SONY CCD with 410,000
(effective) pixels, which provides a
horizontal resolution of 540 TV lines.
The built-in high sensitivity SONY COLOR
CCD enables a clear image even in
0.3Lux(0.1Lux B/W) or as low as 0.002Lux
with SENS-UP.
DAY & NIGHT
DNR (Digital Noise Reduction)
This camera has a function that automatically selects the mode that is
appropriate for daytime or night-time
conditions. The COLOR mode operates in
daytime conditions to provide optimum
colors, and BW mode operates in nighttime conditions to enhance the definition
of the image.
The amount of low illuminance noise
has been significantly reduced, and the
signal-to-noise ratio (S/N ratio) as well as
horizontal resolution have been improved,
resulting in clear and sharp images
displayed even in low light.
Electronic IRIS
Controlled by OSD Menu
The electronic IRIS function enables
continuous automatic control of the
shutter between 1/60~1/120,000 seconds.
The camera functions are controlled by
selecting text displayed on the monitor
screen.
PRIVACY Function
Additional Functions
The PRIVACY function conceals the
areas not required to appear on
the image.
SENS-UP, MOTION DETECTION,
MIRROR, SHARPNESS and SYNC
(INT/LL) functions are also available.
The camera requires periodic inspection.
Contact an authorised technician to carry out the inspection.
Stop using your camera when you find it malfunctioning.
If the camera emits smoke or is unusually hot for a long period,
a fire may be caused.
Do not Install the camera on a surface that can not support it.
If the camera is installed on an inappropriate surface, it may fall
and cause injury.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not dis-assemble the camera.
It may result in an electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in a fire or other hazards.
3 Axis built-in 120mm Dome Housing
ICR540IN D&N Dome Camera
2
3
Digital Day&Night Dome Camera
Contents
Features
2
Camera Operation
14
Menu
14
Settings
15
• LENS (selection)
16
• SHUTTER (condition and speed control)
18
• WHITE BALANCE control
19
• BLC (Back Light Compensation)
20
OSD
10
10
• AGC (Auto Gain Control)
21
VBS-EXTRA
11
• DNR (Digital Noise Reduction)
22
3 Axis Bracket
11
• SENS-UP
23
SMPS
11
• SPECIAL
24
Dimensions
11
• EXIT
29
Installation
12
Troubleshooting
30
Cable Connections
13
Specification
32
Warnings and Precautions
3
Components
8
Names and Functions of Parts
9
Lens
ICR540IN D&N Dome Camera
4
5
Digital Day&Night Dome Camera
Precautions
Do not install the camera in
extreme temperature conditions.
Do not install or use the camera in an
environment where the humidity is high.
Do not drop the camera or protect
it from physical shocks.
Only use the camera under conditions
where temperatures are between
-10°C and +50°C. Be especially
careful to provide ventilation when
operating under high temperatures.
It can cause the image quality to be
poor.
It can cause malfunctions to occur.
Do not install the camera under
unstable lighting conditions.
Do not touch the front lens of the
camera.
ICR540IN D&N Dome Camera
This is one of the most important parts of
the camera. Be careful not to leave
fingerprints on the lens cover.
6
It can damage the CCD.
Do not expose the camera to rain
or spill beverage on it.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that
corrode the electronic components.
Severe lighting change or flicker can
cause the camera to work improperly.
Never keep the camera pointed
directly at strong light.
Do not expose the camera to
radioactivity.
If exposed to radioactivity the CCD
will fail.
• If the camera is exposed to spotlight or object reflecting strong light,
smear or blooming may occur.
• Please check that the power satisfies the normal specification before
connecting the camera.
7
Digital Day&Night Dome Camera
Components
Names and Functions of Parts
1. COLOR DOME CAMERA
2. SCREWS
3. WIRE FOR VBS-EXTRA
4. INSTRUCTION GUIDE
ICR540IN D&N Dome Camera
8
9
Digital Day&Night Dome Camera
Names and Functions of Parts ■
■ Names and Functions of Parts
① LENS : Vari-Focal DC Auto Iris Lens
③ VBS-EXTRA FOR CONNECTING TO LCD
(2.5mm~6.0mm / F1.2, 3.8mm~9.5mm / F1.2
2.9mm~10.0mm / F1.2, 4.0mm~9.0mm / F1.5)
Please use the supplied wire when connecting to LCD
VBS-EXTRA
④ 3 AXIS BRACKET
Please loosen screws and fix tilted and panned position.
(unit : mm)
⑤ SMPS PCB FOR DUAL POWER
② OSD PCB
Dimensions ■
● SET button : Used for the menu display. This button can be used to
confirm settings after changing the value of the selected function or
current conditions.
(unit : mm)
● UP & DOWN buttons : Used for selecting items by moving the cursor
up or down on the menu screen.
● LEFT & RIGHT buttons : Used when changing item values, by moving
the cursor to the left or right on the menu screen.
ICR540IN D&N Dome Camera
10
11
Digital Day&Night Dome Camera
Installation
1. Dome Base Mounting
- Open the dome cover by loosening 3 screws using special wrench
provided.
- Mount the base of camera to a sturdy surface using 4 screws (1.5
inch) and 4 premade holes on the base of the dome.
2. Power Connect & Monitor Impedance
- DC12V/300mA regulated power supply (DC12V only)
AC24V Class 2 power supply (AC24V/DC12V)
- To avoid fire or shock hazard, must use a UL listed power supply.
- Set the monitor impedance switch to 75Ω. Check the impedance
switch when the screen turns blurred.
3. Camera Module Adjustment
- Loosen screws for 3-axis camera bracket and adjust the direction
and angle of camera.
- Make sure to retighten the screws for camera bracket.
- Set any function you wish to activate by using the OSD buttons.
4. Dome Cover Mounting
- Replace the dome cover to the base and tighten 3 screws.
Cable Connections
DC only
⊖
⊕
AC24V/DC12V
AC IN
DC IN
ICR540IN D&N Dome Camera
12
13
AC IN
DC IN
Digital Day&Night Dome Camera
Camera Operation
Menu
Settings
Settings can be made using the 5 buttons located in the camera.
SETUP menu
LENS (selection)
•MANUAL •DC
SHUTTER
(condition and speed control)
•ESC
•MANUAL
•FLK
WHITE BALANCE control
•ATW
•AWC
•MANUAL
BACKLIGHT
(Backlight Compensation)
•OFF
•HIGH
•LOW
•MIDDLE
AGC (Auto Gain Control)
•OFF
•HIGH
•LOW
•MIDDLE
DNR
(Digital Noise Reduction)
•OFF
•HIGH
•LOW
SENS-UP (Low illuminance)
•OFF
•AUTO
SPECIAL
•CAMERA ID
•SYNC
•PRIVACY
•SHARPNESS
•RETURN
EXIT
•MIDDLE
•COLOR
•MOTION DETECTION
•MIRROR
•RESET
1. Press the SET button
•Settings can now be made. The SETUP menu is displayed on the monitor.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
DNR
SENS-UP
SPECIAL
EXIT
MANUAL
ESC
ATW
OFF
LOW
LOW
OFF
2. Select a menu item from the list available by using the UP and DOWN buttons.
•The cursor can be moved up or down by using the UP and DOWN buttons.
Position the cursor to point to the function requiring adjsutment.
ICR540IN D&N Dome Camera
14
15
Digital Day&Night Dome Camera
Camera Operation
MANUAL : Manual Lens selection
SETUP
Select any function you
wish to operate by
using the UP and
DOWN buttons.
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
DNR
SENS-UP
SPECIAL
EXIT
MANUAL
ESC
ATW
OFF
LOW
LOW
OFF
Modes can be changed
using the LEFT and
RIGHT buttons.
3. When the LEFT or RIGHT button is pressed, available values and modes are
displayed in order. Keep pressing the button until you get to the mode you wish to
select.
DC : Auto Iris Lens selection
Note
• The brightness of the screen can be adjusted in DC mode. The brightness
can be adjusted within the range of 1 ~ 70. The optimum level of brightness
for the user can be achieved by adjustment.
• If you select the MANUAL mode, it can be adjusted in ESC mode.
4. Select 'EXIT' and then press the SET button to exit the set up Menu.
Note
• If appears at the mode you wish to operate, it means that there is a
sub-menu which can be selected by pressing the SET button.
• If
appears at the mode item, it means that there is no mode
available to be selected.
LENS (selection)
This function is used to adjust the brightness of the screen.
3. Press the SET button if you wish to return to the previous menu
1. When the SETUP menu is displayed on the screen, position the cursor to point
to 'LENS' by using the UP and DOWN buttons.
2. Select the type of the lens setting to use by pressing the LEFT or RIGHT button.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
ICR540IN D&N Dome Camera
16
DC
--ATW
OFF
17
Digital Day&Night Dome Camera
Camera Operation
BLC (Back Light Compensation)
AGC (Auto Gain Control)
When there is a strong backlight behind the object, clear images of the
background as well as the object can still be obtained by using the
BACKLIGHT function.
1. Position the cursor to point to 'BACKLIGHT' on the SETUP menu by using
the UP and DOWN buttons.
2. Select the value required by pressing the LEFT or RIGHT button.
1. Position the cursor to point to 'AGC' on the SETUP menu by using the
UP and DOWN buttons.
2. Select the value required by pressing the LEFT or RIGHT button. As the
level of gain increases the screen gets brighter but the level of noise will
also increase.
HIGH
: The gain varies between the range of 6dB ~ 42dB.
MIDDLE : The gain varies between the range of 6dB ~ 30dB.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
DNR
MANUAL
ESC
ATW
OFF
LOW
LOW
HIGH
: The gain increases from 0dB up to 42dB.
MIDDLE : The gain increases from 0dB up to 30dB.
LOW
: The gain increases from 0dB up to 18dB.
OFF
: BACKLIGHT function does not operate.
ICR540IN D&N Dome Camera
20
LOW
: The gain varies between the range of 6dB ~ 18dB.
OFF
: The gain is fixed at 6dB.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
DNR
SENS-UP
SPECIAL
EXIT
MANUAL
ESC
ATW
OFF
LOW
LOW
OFF
21
Digital Day&Night Dome Camera
Camera Operation
DNR (Digital Noise Reduction)
The level of background noise in low light decreases automatically as the
level of gain changes.
1. Position the arrow to point to 'SENS UP' on the SETUP menu by using the
UP and DOWN buttons.
1. Position the cursor to point to 'DNR' on the SETUP menu by using the
UP and DOWN buttons.
2. Select the value required by pressing the LEFT or RIGHT button.
2. Select the value required by pressing the LEFT or RIGHT button.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
DNR
SENS-UP
SPECIAL
OFF
LOW
MANUAL
ESC
ATW
OFF
LOW
LOW
OFF
AUTO
: Low light level automatic mode.
OFF
: The function does not operate.
Note
• When SHUTTER is in the manual or flk mode, SENS UP does not operate.
• When AGC is turned off, SENS UP does not operate.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
DNR
SENS-UP
SPECIAL
EXIT
: There is no reduction in noise level.
: There is a small reduction in noise level with almost no
ghost image.
MIDDLE : The most effective mode. There is a sufficient reduction in
noise levels without causing significant ghosting.
HIGH
: The level of noise is reduced greatly, however there is an
increase in ghosting.
MANUAL
ESC
ATW
OFF
LOW
LOW
OFF
3. Press the SET button when all the settings are complete.
Note
Note
• When AGC is turned off, DNR does not operate.
SENS UP (Low Illuminance)
• The maximum storage magnification in low light level movement situations
can be adjusted by pressing the SET button in 'AUTO' mode.(X2~X128)
• As the magnification increases the screen gets brighter; however the after
image also increases.
• If storage magnification is increased while SENS UP is operational, it may
cause noise and spots may appear; this is normal.
SENS UP helps maintain a bright, clear screen image by automatically
detecting changes in the level of light in low light level conditions.
ICR540IN D&N Dome Camera
22
23
Digital Day&Night Dome Camera
Camera Operation
SPECIAL
1. Position the cursor to point to 'SPECIAL' on the SETUP menu by using the
UP and DOWN buttons.
3) Press the SET button.
2. Select the mode required by pressing the UP or DOWN button.
SPECIAL
CAMERA ID
COLOR
SYNC
MOTION DET
PRIVACY
MIRROR
SHARPNESS
RESET
RETURN
OFF
ON
INT
OFF
OFF
OFF
ON
4) Up to 15 characters can be used for the camera ID.
Move the cursor to the letter required by using the UP and DOWN button.
CAMERA ID : If an ID is input, this camera ID appears on the monitor
and recorded footage.
1) Position the cursor to point to ‘CAMERA ID’ by using the
UP or DOWN button.
2) Select 'ON' by pressing the LEFT or RIGHT button.
Select an ID from A,B~Y,Z, a,b~y,z, 0,1~8,9 by using the UP, DOWN,
LEFT and RIGHT buttons.
Lock in the characters by using the SET button.
• Once locked in the cursor moves to the next space in the ID.
Repeat the above steps until the ID is complete.
Note
• If 'OFF' is selected, the ID does not
appear on the monitor even if it has
been input.
ICR540IN D&N Dome Camera
24
SPECIAL
CAMERA ID
COLOR
SYNC
MOTION DET
PRIVACY
MIRROR
SHARPNESS
RESET
RETURN
OFF
ON
INT
OFF
OFF
OFF
ON
Note
• If the wrong name has been input.....
Press the SET button after moving the cursor to CLR and all the letters will be
erased. If you want to correct a letter move the cursor to the arrow at the bottom
left of the screen and press 'SET'.
Position the cursor above the letter you wish to correct and then move the cursor
onto the letter you wish to choose and press the SET button.
25
Digital Day&Night Dome Camera
Camera Operation
5) When the camera ID is complete, select a position for the name to be
displayed.
Move the cursor onto 'POS' and then press the SET button.
Note
• When the AGC is turned off, COLOR does not operate.
• When an infrared light is used, there may be a problem with focusing.
SYNC : Two sychronisation modes are available, INTERNAL and
EXTERNAL LINE-LOCK. In LINE-LOCK mode, it synchronises the
video signal between cameras without a synchronous generator.
The line-lock synchronisation is only used in areas of 60Hz
(NTSC Models) / 50Hz (PAL Models).
The ID will appear in the top left
corner.
- INT : Internal synchronisation
- LL : External line-lock synchronisation
• If ‘LL’ is selected, it can be adjusted to the desired phase.
Press the SET button.
• Adjust to the desired phase from 0 to 359.
Select the position where the ID is
to be displayed by using the 4 directional
buttons, and then press the SET button.
Note
6) Select 'END' and press the SET button to complete ID input.
COLOR
• When the mains frequency is 50Hz, the line-lock mode (NTSC Models) cannot be used.
• When the mains frequency is 60Hz, the line-lock mode (PAL Models) cannot be used.
- AUTO : This camera has an IR Cut Filter and automatically changes
to the appropriate mode dependant on lighting levels.
COLOR mode is selected during daylight and B/W mode at
night time.
- ON : The color mode is selected by default, and the modes do not
change automatically.
ICR540IN D&N Dome Camera
26
27
Digital Day&Night Dome Camera
Camera Operation
MOTION DETECTION:
This product has a feature that allows you to observe movements of objects
in 4 different areas on the screen, and the words 'MOTION DETECTED'
appear on the screen when movement is detected; hence a single individual
can conduct supervision efficiently. The camera detects an object's
movement by sensing disparity of outline, and level of brightness and color.
• Please press the SET button.
- OFF : MOTION DETECTION mode is cancelled.
- ON : Any motion in the selected areas is observed.
• Please select the area you wish to observe from the 4 areas in AREA
SEL mode.
• Please select ON mode for the chosen area.
• Please adjust the size of the area to be observed by using the UP,
DOWN, LEFT or RIGHT button.
• Please select the area you do not wish to appear from the 4 areas in
AREA SEL mode.
• Please select ON mode for the chosen area.
• Please adjust the size of the area to be concealed by using the UP, DOWN,
LEFT or RIGHT button.
MIRROR
- ON : Sets a horizontal image inversion.
- OFF : Cancels the inversion.
SHARPNESS : The outline of the video image becomes cleaner and
more distinctive as the level of SHARPNESS increases. If the level goes
up excessively, however, it may affect the video image and generate noise.
• Please press the SETUP button.
• Please press the SET button to save the changes and complete the setting.
PRIVACY : This mode conceals the areas you do not wish to appear on the screen.
- OFF : Cancels the PRIVACY mode. - ON : Operates the PRIVACY mode.
• Please press the SET button.
• The available range of level is 0 ~ 31.
RESET : Returns to the level which was set by the manufacturer for shipment.
RETURN : Saves the SPECIAL menu and returns to the SETUP menu.
EXIT
Saves all the setting menus and then exits.
ICR540IN D&N Dome Camera
28
29
Digital Day&Night Dome Camera
Troubleshooting
If there are problems with the camera operation, check the tables below. If
the problem persists, please contact the agent who supplied the product.
Problems
Nothing appears on the
screen.
The video image is not
clear.
The screen is dark.
There is a problem with
the camera operation.
The camera surface is
too hot and black stripes
appear on the screen.
Troubleshooting
Problems
Troubleshooting
The MOTION
DETECTION function is
not working.
• Check if 'MOTION DETECTION' mode is
turned on.
Colors are not quite
right.
• Check the 'WHITE BAL' setting.
(Please refer to page 19)
The screen is
flickering.
• Check if the camera is facing directly into
sunlight or fluorescent light.
L/L mode isn't able to
be selected.
• Have you connected your camera to DC power
source? Connect it to AC power source.
L/L mode is not
available.
• Check the frequency of power supply
(60Hz for NTSC, 50Hz for PAL).
COLOR mode is not
working.
• Check if the AGC menu is set to the OFF
position.
SENS-UP function is not
working.
• Check if the AGC menu is set to the OFF
position.
• Check the setting of the MD AREA.
• Check the power connection.
• Check the video signal line connection.
• Make sure that the lens is clean.
Clean the lens with a clean lint free cloth or
brush.
• Adjust the contrast control on the monitor.
• Make sure that the screen is not exposed
directly to a bright light.
Re-position the camera if necessary.
• Adjust the contrast control of the monitor.
• If there is an intermediate device, set the75ohm
Hi-z correctly, and also check the connections.
• If necessary, adjust the brightness level.
• Check if an appropriate power source to
the camera complies with the manufacturer's
standard requirement, or if the voltage is
fluctuating. Check for ground loops.
ICR540IN D&N Dome Camera
30
• Check if the SHUTTER menu is set to
MANUAL mode.
31
Digital Day&Night Dome Camera
Specifications
ITEM
Power Source
C
C
D
s
y
n
c
NTSC
AC24V / DC12V
DC12V
AC24V / DC12V
215mA(AC24V)/250mA(DC12V)
160mA
215mA(AC24V)/250mA(DC12V)
Total Pixels
811(H) x 508(V)
795(H) x 596(V)
Effective Pixels
768(H) x 494(V)
752(H) x 582(V)
Size
Scanning System
Synchronization
Frequency
Horizontal:15.734 KHz Vertical :59.94 Hz
0~359°(Adjustable)
INT/LL Selectable
INT
0~359°(Adjustable)
Horizontal: 15.625 KHz Vertical : 50.00 Hz
1.0Vp-p/75(Video 0.714Vp-p Sync 0.286Vp-p)
1.0Vp-p/75 (Video 0.7 Vp-p Sync 0.3 Vp-p)
50dB (AGC Off)
0.3Lux/F1.2(Color), 0.1Lux/F1.2(B/W), 0.002Lux(Sens-up)
Gain Control
OFF / LOW / MIDDLE / HIGH
White Balance
ATW / AWC / MANUAL(1,800°K~10,500°K)
Electronic Shutter Speed
INT
540 TV Lines
S/N (Y signal)
Min. Illumination
160mA
2:1 Interlace
INT/LL Selectable
Video Output
DC12V
1/ 3 inch interline transfer CCD
Resolution
E
L
E
C
T
R
I
C
A
L
PAL
AUTO / MANUAL(1/60~1/120,000)
Sens-Up
AUTO / MANUAL(1/50~1/120,000)
OFF / AUTO
O.S.D
Built-in
Motion Detection
ON / OFF (4 Programmable Zone)
DNR
OFF / LOW / MIDDLE / HIGH(Noise Reduction)
Mirror
Built-in (Horizontal Image Inversion)
Privacy Function
ON / OFF (4 Programmable Zone)
Operating Temperature/Humidity
-10°C ~ +50°C / 30 ~ 90% RH
Weight
ICR540IN D&N Dome Camera
630g
32
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising