View detail for AT88CK109STK8 Getting Started Guide

View detail for AT88CK109STK8 Getting Started Guide
Atmel CryptoAuthentication Starter Kit
Atmel AT88CK109STK8
Getting Started Guide
Features
Contents
 Installing Atmel CryptoAuthentication Evaluation
Studio (ACES)
 Atmel AT88CK109BK8 daughter board
 Powering the board
 6” USB cable
 Reading the device configuration information
Atmel ATSHA204 device
 Atmel AT88Microbase – AVR base module
 Atmel ATSHA204 samples
Introduction
Atmel® AT88CK109STK8 is an Atmel CryptoAuthentication starter kit, which can be used as a reference design
for an USB application requiring the Atmel CryptoAuthentication product family.
Figure 1.
Atmel AT88CK109STK8 starter kit
8739A–SMEM–3/11
1.
Install ACES (Atmel CryptoAuthentication Evaluation Studio)
Visit www.atmel.com/cryptokits to download and install the latest ACES
2.
Configuring the Atmel AT88CK109BK8 and Atmel AT88Microbase
boards

Ensure the Atmel ATSHA204 device in place in the socket with the correct Pin1 orientation

The K1 switch on the Atmel AT88CK109BK8 board should always be in the “uBase” position when
mounted to the Atmel AT88Microbase

The 8ld SOIC package supports both SWI (Single Wire Interface) and I2C communication protocol.
The following steps configure the kit for I2C communication, since the samples in this kit are shipped
with I2C enabled.
Figure 2-1.
Atmel AT88CK109BK8 CryptoAuthentication daughter board
Pin 1 Indicator

The K1 switch on the Atmel AT88CK109BK8 board should always be in the “uBase” position when
mounted to the Atmel AT88Microbase
Table 2-1. Atmel AT88Microbase with an Atmel AT90USB1287 AVR
2
Atmel AT88CK109STK8 Getting Started Guide
8739A–SMEM–3/11
Table 2-2. Configuration table
Configuration table
3.
Communication protocol
Atmel AT88CK101BK8
(K1 switch setting)
Atmel AT88Microbase
(K1 switch setting)
Comments
I2C
uBase
TWI (I2C)
Kit shipped with this setup
SWI
uBase
SPI
Powering up the board
The Atmel AT88CK109STK8 is a USB powered device.

Simply insert the board into an open USB port
Figure 3-1.
Atmel AT88CK109STK8 USB powered
Power LEDs
AT88Microbase
CLIENT
HOST
Atmel AT88CK109STK8 Getting Started Guide
8739A–SMEM–3/11
3
4.
Reading the device configuration zone

Insert the Atmel AT88CK109STK8 into a USB port

Launch ACES CE for the desktop shortcut icon or from
Start / All Programs / Atmel Crypto Solutions / ACES / ACES CE
Figure 4-1.

Figure 4-2 will appear indicating the board (CK109), device (SHA204), firmware version (0.0.6), and
the communication interface (TWI)
Figure 4-2.
4
ACES
Kit detection screen

Selecting the Show Quick Start Guide check box will launch the QSG alongside the configuration
environment.

Click the “Select Kit” button to launch ACES Configuration Environment – ATSHA204 pane
Atmel AT88CK109STK8 Getting Started Guide
8739A–SMEM–3/11
Figure 4-3.

ACES configuration environment – Atmel ATSHA204
All three System Status fields should be green and populated, which indicates the proper
communication with the development kit and the Atmel ATSHA204 device
Kit Name:
Device:
DevRev:
5.
CK101 0.0.5 SWI8
ATSHA204
00 00 00 03
Executing the Validate MAC command

Go to Tools \ Validate MAC to launch the Validate MAC window, see Figure 5-1
Atmel AT88CK109STK8 Getting Started Guide
8739A–SMEM–3/11
5
Figure 5-1.

Figure 5-2 will appear

Click the Execute Nonce button

Click the MAC button

Click the CheckMac button

The CheckMac Result: should indicate Matched
Figure 5-2.
6
Validate MAC tools menu
Validate MAC pane
Atmel AT88CK109STK8 Getting Started Guide
8739A–SMEM–3/11
Congratulations, your Atmel AT88CK109STK8 is up and running.
See ACES online Help additional information.
For additional samples, go to: http://www.atmel.com/forms/Samples.asp?family_id=699
6.
Additional kits information
Atmel CryptoAuthentication kits
Atmel kits
Atmel device
supported
Device
footprint
Communication
protocol
Socket(s)
AT88CK454BLACK
ATSHA204
SOT23-3
SWI
None/USB Dongle
AT88CK101STK3
ATSHA204
SOT23-3
SWI
1
AT88CK101STK8
ATSHA204
8LD SOIC
SWI/I C
1
AT88CK109STK3
ATSHA204
SOT23-3
SWI
2
AT88CK109STK8
7.
2
ATSHA204
8LD SOIC
2
SWI/I C
2
Firmware Upgrade
See application note, doc8746, “Upgrading Crypto Kits Firmware.”
8.
References and further information
A complete reference design including schematics, Gerber files, bill of materials (BOM), hardware user
guide and development and demonstration software is conveniently downloadable from the Atmel website
at www.atmel.com/cryptokits.
Atmel AT88CK109STK8 Getting Started Guide
8739A–SMEM–3/11
7
9.
EVALUATION BOARD/KIT IMPORTANT NOTICE
This evaluation board/kit is intended for ENGINEERING, DEVELOPMENT, DEMONSTRATION or
EVALUATION PURPOSE ONLY. It is not a finished product and may not (yet) comply with some or
any technical or legal requirements that are applicable to finished products, including, without limitations,
directives regarding electromagnetic compatibility, recycling (WEEE), FCC, CE or UL (except as may be
otherwise noted on the board/kit). Atmel® supplied this board/kit “AS IS,” without any warranties, with
all faults, at the buyer’s and further users’ sole risk. The user assumes all responsibly and liability for
proper and safe handling of goods. Further, the user indemnifies Atmel from claims arising from the
handling or use of goods. Due to open construction of the product, it is the user’s responsibility to take
any and all appropriate precautions with regard to electrostatic discharge and any other technical or legal
concerns.
EXCEPT TO THE EXTENT OF INDEMNITY SET FORTH ABOVE, NEITHER USER NOR ATMEL SHALL BE
LIABLE TO EACH OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
No license is granted under any patent right or other intellectual property right of Atmel covering or
relating to any machine, process, or combination in which such Atmel product or services might be or are
used.
Mailing Address: Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
8
Atmel AT88CK109STK8 Getting Started Guide
8739A–SMEM–3/11
Atmel Corporation
Atmel Asia Limited
Atmel Munich GmbH
Atmel Japan
2325 Orchard Parkway
Unit 01-5 & 16, 19F
Business Campus
9F, Tonetsu Shinkawa Bldg.
San Jose, CA 95131
BEA Tower, Millennium City 5
Parkring 4
1-24-8 Shinkawa
USA
418 Kwun Tong Road
D-85748 Garching b. Munich
Chuo-ku, Tokyo 104-0033
Tel: (+1)(408) 441-0311
Kwun Tong, Kowloon
GERMANY
JAPAN
Fax: (+1)(408) 487-2600
HONG KONG
Tel: (+49) 89-31970-0
Tel: (+81)(3) 3523-3551
www.atmel.com
Tel: (+852) 2245-6100
Fax: (+49) 89-3194621
Fax: (+81)(3) 3523-7581
Fax: (+852) 2722-1369
© 2011 Atmel Corporation. All rights reserved. / Rev.: 8739A–SMEM–3/11
Atmel®, logo and combinations thereof, CryptoAuthentication™ and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other
terms and product names may be trademarks of others.
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this doc ument or in
connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON T HE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS
ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF ME RCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND
PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel
makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and rese rves the right to make changes to specifications and products descriptions at any time without
notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise , Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel
products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life .
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising