HS9A,HSV1,HS2V1,HSY Series Remote Controller Manual

HS9A,HSV1,HS2V1,HSY Series Remote Controller Manual
AIR CONDITIONER
REMOTE CONTROLLER ILLUSTRATION
CS406-R51E
202055090357
20100119
Thank you very much for purchasing our air conditioner.
Please read this owner's manual carefully before using
your air conditioner.
Handling the remote controller
CONTENTS
Location of the remote controller.
Use the remote controller within a distance of 8
meters from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.
Handling the remote controller ...................................................... 2
Remote controller Specifications...................................................
3
Function buttons .................. .........................................................
4
8m
SET
TEM
PERA
TUR
E(
AUTO
CO
OL
DRY
HEAT
C)
FAN
HIG
H
ME
D
LOW
TEM
P
MO
DE
Indicators on LCD ..........................................................................
6
ON
/OF
F
SW
ING
ECON
OM
Y
ION
RES
ET
FOL
LOW
ME
LOC
K
TIM
ER
TIM
ER
LED
DIS
PLA
Y TU
FAN
SPE
ED
ON
OFF
RBO
How to use the buttons .................................................................
7
Auto operation.................................................................................
7
Cooling/Heating/Fan operation......................................................
7
Dehumidifying operation ...............................................................
8
Swing operation..............................................................................
8
Timer operation...............................................................................
9
ECONOMY operation ....................................................................
12
CAUTIONS
The air conditioner will not operate if curtains, doors or other materials
block the signals from the remote controller to the indoor unit.
Prevent any liquid from falling into the remote controller. Do not expose
the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller, either move
these appliances or consult your local dealer.
Replacing batteries
.
1
The remote controller is powed by two dry
batteries(R03/LR03X2) housed in the rear
part and protected by a cover.
(1) Remove the cover by pressing and sliding off.
(2) Remove the old batteries and insert the new
batteries,placing the(+) and (-) ends correctly.
(3) Reattach the cover by sliding it back into
position.
NOTE: When the batteries are removed, the
remote controller erases all programming.
After inserting new batteries, the remote
controller must be reprogrammed.
2
CAUTIONS
Function buttons
TEMP UP Button
Push this button to increase the indoor tempero
o
ature setting in 1 C(2 F) increments to 30 C(88 F).
2 TEMP DOWN Button
Push this button to decrease the indoor temperature setting in 1oC(2 F) increments to 17oC(62 F).
1
Do not mix old and new batteries or batteries of a different type.
Do not leave the batteries in the remote controller if it is not going
to be used for 2 or 3 months.
Dispose of the old batteries in the special containers to be found
in the sales outlets.
SET TEMPERATURE( C)
Remote Controller Specifications
Model
R51I5/BG(C)E, R51I6/BG(C)E,
R51I7/BG(C)E, R51I8/BG(C)E, R51I9/BG(C)E;
R51I10/BG(C)E, R51I11/BG(C)E, R51I12/BG(C)E;
Rated Voltage
Lowest Voltage of
CPU Emitting Signal
2.0V
Signal Receiving
Range
8m (when using 3.0 voltage,
it Gets 11m)
Environment
2)
AUTO
ON/OFF FAN SPEED
MODE
SWING
ECONOMY
TIMER ON
4
ION
5
O
RESET LOCK
TIMER OFF
FOLLOW
LED
ME
DISPLAY TURBO
6
7
NOTE:
Temperature setting display:
Celsius scale( C): R51I5/BG(C)E, R51I6/BG(C)E, R51I7/BG(C)E, R51I8/BG(C)E,
Fahrenheit scale( F): R51I9/BG(C)E; R51I10/BG(C)E, R51I11/BG(C)E, R51I12/BG(C)E.
Performance Feature
1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling only
model without), and FAN.
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17 C~30 C(62OF~88OF).
4. Full function of LCD (Liquid Crystal Display)
5. Back light emitting.
2
8
9
10
11
12
13
14
15
COOL
DRY
HEAT
FAN
NOTE: Heat mode is for Cooling & Heating models only.
4
SWING Button
Used to stop or start louver movement and
set the desired up/down airflow direction.
5 ION Button(Optional)
When push this button, the ion generator is
energized and will help to remove pollen and
impurities from the air.
6 FOLLOW ME Button(Optional)
O
-5 C~ 60 C( -41 F~140 F )
Each time the button is pressed, the operation
mode is selected in the sequence of the following:
TEMP
1
3
3.0V(Dry batteries R03/LR03
3 MODE Button
FAN
HIGH
MED
LOW
AUTO
COOL
DRY
HEAT
Model: R51I5/BG(C)E,
R51I6/BG(C)E,
R51I7/BG(C)E,
R51I8/BG(C)E.
ION and FOLLOW button:
Optional function.
Push this button to initiate the Follow Me
function, the remote controller begins to detect
the actual temperature at its location. The
remote controller will send this signal to the
air conditioner every 3 minutes interval until
press the Follow Me button again. The air
conditioner will beep to indicate the Follow Me
feature has ended if it does not receive the
signal during any 7 minutes interval.
7 RESET Button
Once the recessed RESET button is pressed,
all of the current settings will be cancelled
and the controller will return to the initial settings.
8 ON/OFF Button
Operation starts when this button is pressed
and stops when the button is pressed again.
9 FAN SPEED Button
Used to select the fan speed in four steps:
Auto Low Med High
10 TIMER ON Button
Press this button to activate the Auto-on time
setting. Each press will increase the time setting
3
4
Indicators on LCD
Function buttons(continued)
MODE display
in 30 minutes increments, up to 10 hours, then at
1 hour increments up to 24 hours. To cancel the
Auto-on time setting, just press the button until
the time setting is 0.0.
SET TEMPERATURE( F)
FAN
HIGH
MED
LOW
AUTO
COOL
DRY
HEAT
TEMP
ON/OFF FAN SPEED
MODE
SWING
ION
ECONOMY TIMER ON
RESET LOCK
TIMER OFF
FOLLOW
LED
ME
DISPLAY TURBO
Model: R51I9/BG(C)E,
R51I10/BG(C)E,
R51I11/BG(C)E,
R51I12/BG(C)E.
ION and FOLLOW button:
Optional function.
Displays the current selected mode.
Including AUTO, COOL, DRY, HEAT
(cooling & heating models only) and
FAN.
Transmission Indicator
11 ECONOMY Button
This transmission indicator will light
when remote controller transmits
signals to the indoor unit.
Select this function during the sleeping time. It
can maintain the most comfortable temperature
and save energy. This function is available on
COOL, HEAT or AUTO mode only .
Temp./Timer display
The temperature setting (from 17oC(62 F)
to 30oC(88 F)) or timer setting (0~24h) will
be displayed. If FAN mode is
selected, there will be no display.
NOTE: While the unit is running under Energy-saving
mode, it would be cancelled if press MODE, FAN
SPEED or ON/OFF button.
ON/OFF display
12 TIMER OFF Button
Press this button to activate the Auto-off time
setting. Each press will increase the time setting
in 30 minutes increments, up to 10 hours, then at
1 hour increments up to 24 hours. To cancel the
Auto-off time setting, just press the button until
the time setting is 0.0.
13 LOCK Button
Press this recessed button to lock all current
settings, and the remote controller will not accept
any operation except that of the LOCK. Use the
LOCK mode when you want to prevent settings
from being changed accidentally. Press the LOCK
button again to cancel the LOCK function. A lock
symbol will appear on the remote controller display
when the lock function is activated.
14 Turbo Button
Used to start or stop the speed cooling/
heating.(Speed cooling/heating operates super
high fan speed in cooling/heating mode.)
Note: The unit system will automatically
revert back to the previous settings after
continue operating under speed cooling
mode for about 20 minutes.
15 LED Display Button
Press this button to clear the display on the
indoor unit, press it again to light the display .
5
This indicator will be displayed when
the unit is operating.
SET TEMPERATURE
TIMER ON OFF
MODE display(FAN mode)
FAN SPEED display
Displays the selected fan speed:
AUTO, HIGH, MED and LOW.
Nothing displays when the fan speed
is selected in AUTO speed. When
AUTO or DRY Mode is selected, there
will be no signals displayed.
FOLLOW ME display(on some models)
When pressing FOLLOW ME button
in COOL or HEAT mode, the remote
sensing function is activated and this
indicator displays.
TIMER display
This display area shows the settings
of the TIMER. That is, if only the
Auto-on time function is set, it will
display TIMER ON. If only the Auto-off
time function is set, it will display
TIMER OFF. If both functions are
set, it will display TIMER ON OFF
which indicates you have chosen both
the Auto-on time and Auto-off time.
LOCK Indicator
LOCK display is displayed when
pushing the LOCK button. Push the
LOCK button to clear display.
6
How to use the buttons
Dehumidifying operation
SET TEMPERATURE( C)
Auto operation
FAN
HIGH
MED
LOW
AUTO
COOL
DRY
HEAT
TEMP
2
ON/OFF FAN SPEED
MODE
3
1
SWING
ION
ECONOMY
RESET LOCK
TIMER ON
TIMER OFF
FOLLOW
LED
ME
DISPLAY TURBO
Ensure the unit is plugged in and power is
available. The OPERATION indicator on the
display panel of the indoor unit illuminates.
1. Press the MODE button to select Auto.
2. Press the TEMP button to set the desired
temperature. The temperature can be set
within a range of 17 C(62 F)~ 30 C in 1 C(2 F)
increments.
3. Press the ON/OFFbutton to start the air
conditioner.
NOTE
SET TEMPERATURE( C)
FAN
HIGH
MED
LOW
AUTO
COOL
DRY
HEAT
TEMP
2
ON/OFF FAN SPEED
MODE
1
SWING
ION
ECONOMY
RESET LOCK
TIMER ON
TIMER OFF
FOLLOW
LED
ME
DISPLAY TURBO
1. In the Auto mode, the air conditioner can logically
choose the mode of Cooling, Fan, Heating and
Dehumidifying by sensing the difference between the
actual ambient room temperature and the set temperature on the remote controller.
2. In the Auto mode, you can not switch the fan speed.
It has already been automatically controlled.
3. If the Auto mode is not comfortable for you , the
desired mode can be selected manually.
Cooling /Heating/Fan operation
FAN
HIGH
MED
LOW
TEMP
2
ON/OFF FAN SPEED
MODE
1
4
3
SWING
ION
ECONOMY
RESET LOCK
TIMER ON
TIMER OFF
FOLLOW
LED
ME
DISPLAY TURBO
Ensure the unit is plugged in and power is
available.
1. Press the MODE button to select COOL, HEAT,
(cooling & heating models only) or FAN mode.
2. Press the TEMP button to set the desired
temperature. The temperature can be set
within a range of 17 C(62 F)~ 30 C in 1 C(2 F)
increments.
3. Press the FAN SPEED button to select the
fan speed in four steps- Auto, Low, Med,or High.
4. Press the ON/OFF button to start the air
conditioner.
NOTE
In the FAN mode, the setting temperature is not
displayed in the remote controller and you are not
able to control the room temperature either. In this
case, only step 1, 3 and 4 may be performed.
7
In the Dehumidifying mode, you can not switch
the fan speed. It has already been automatically
controlled.
Swing operation
SET TEMPERATURE( C)
SET TEMPERATURE( C)
AUTO
COOL
DRY
HEAT
3
Ensure the unit is plugged in and power is
available. The OPERATION indicator on the
display panel of the indoor unit illuminates.
1. Press the MODE button to select DRY mode.
2. Press the TEMP button to set the desired
temperature. The temperature can be set
within a range of 17 C(62 F)~ 30 C in 1 C(2 F)
increments.
3. Press the ON/OFF button to start the air
conditioner.
NOTE
FAN
HIGH
MED
LOW
AUTO
COOL
DRY
HEAT
TEMP
ON/OFF FAN SPEED
MODE
1
SWING
ION
ECONOMY
RESET LOCK
TIMER ON
TIMER OFF
FOLLOW
LED
ME
DISPLAY TURBO
Use the SWING button to adjust the Up/Down
airflow direction.
1. When press the button once and quickly, the
air flow direction setting feature of the louver is
activated. The moving angle of the louver is
6o for each press. Keep pressing the button to
move the louver to the desired position.
2. If keep pressing the SWING button without
releasing for 2 more seconds, the auto swing
feature of the louver is activated. The horizontal
louver would swing up/down automatically.
Press it again to stop.
NOTE: When the louver swing or move to a
position which would affect the cooling
and heating effect of the air conditioner,
it would automatically change the swing/
moving direction.
8
Timer operation
press the TIMER ON button can set the auto-on
time of the unit. And press the TIMER OFF button
can set the auto-off time of the unit.
SET TEMPERATURE( C)
AUTO
COOL
DRY
HEAT
TIMER ON
FAN
HIGH
MED
LOW
TEMP
ON/OFF FAN SPEED
MODE
SWING
ECONOMY TIMER ON
1
ION
RESET LOCK
TIMER OFF
2
FOLLOW
LED
ME
DISPLAY TURBO
To set the Auto-on time.
1. Press the TIMER ON button. The remote
controller shows TIMER ON, the last Auto-on
setting time and the signal "h" will be shown on
the LCD display area. Now it is ready to reset the
Auto-on time to START the operation.
2. Push the TIMER ON button again to set desired
Auto-on time. Each time you press the button,
the time increases in 30 minutes increments, up
to 10 hours, then at 1 hour increments up to 24
hours.
3. After setting the TIMER ON ,there will be a onehalf second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "h" will disappear and the set temperature
will re-appear on the LCD display window.
To set the Auto-off time.
1. Press the TIMER OFF button. The remote
controller shows TIMER OFF, the last Auto-off
setting time and the signal "h" will be shown on
the LCD display area. Now it is ready to
reset the Auto-off time to START the operation.
2. Push the TIMER OFF button again to set desired
Auto-off time. Each time you press the button,
the time increases in 30 minutes increments, up
to 10 hours, then at 1 hour increments up to 24
hours.
3. After setting the TIMER OFF ,there will be a onehalf second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "h" will disappear and the set temperature
will re-appear on the LCD display window.
9
IMPORTANT
The effective operation time set by the remote controller for the timer
function is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0,
3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13,
14, 15,16,17, 18, 19, 20, 21, 22, 23 and 24.
Example of Timer setting
TIMER ON
(Auto-on Operation)
The TIMER ON feature is useful when you want
the unit to turn on automatically before you return
home. The air conditioner will automatically start
operating at the set time.
h
TIMER ON
Start
Off
Set
6 hours later
Example:
To start the air conditioner in 6 hours.
1. Press the TIMER ON button, the last setting of
starting operation time and the signal "h" will
show on the display area.
2. Press the TIMER ON button to display "6:0h" on
the TIMER ON display of the remote controller.
3. Wait for about 3 seconds and the digital display
area will show the temperature again. Now this
function is activated.
10
TIMER OFF
TIMER OFF
Example:
To stop the air conditioner in 10 hours.
1. Press the TIMER OFF button, the last setting of
stopping operation time and the signal "h" will
show on the display area.
2. Press the TIMER OFF button to display "10h" on
the TIMER OFF display of the remote controller.
3. Wait for about 3 seconds and the digital display
area will show the temperature again. Now this
function is activated.
Stop
On
Set
10 hours later
COMBINED TIMER
(Setting both ON and OFF timers simultaneously)
h
TIMER ON OFF
Start
Stop
On
Set
h
(Auto-off Operation)
The TIMER OFF feature is useful when you want
the unit to turn off automatically after you go to bed.
The air conditioner will stop automatically at the set
time.
h
2 hours later
after setting
10 hours later
after setting
TIMER OFF
TIMER ON
(On
Stop
Start operation)
This feature is useful when you want to stop the air
conditioner after you go to bed, and start it again in
the morning when you wake up or when you return
home.
Example:
To stop the air conditioner 2 hours after setting
and start it again 10 hours after setting.
1. Press the TIMER OFF button.
2. Press the TIMER OFF button again to
display 2.0h on the TIMER OFF display.
3. Press the TIMER ON button.
4. Press the TIMER ON button again to
display 10h on the TIMER ON display .
5. Wait for the remote control to display
the setting temperature.
11
TIMER ON OFF
Start
Stop
Off
Set
2 hours later
after setting
5 hours later
after setting
TIMER ON
TIMER OFF
(Off
Start
Stop operation)
This feature is useful when you want to start
the air conditioner before you wake up and
stop it after you leave the house.
Example:
To start the air conditioner 2 hours after
setting, and stop it 5 hours after setting.
1. Press the TIMER ON button.
2. Press the TIMER ON button again to
display 2.0h on the TIMER ON display.
3. Press the TIMER OFF button.
4. Press the TIMER OFF button again to
display 5.0h on the TIMER OFF display .
5. Wait for the remote control to display
the setting temperature.
! CAUTION
The timer setting(TIMER ON or TIMER OFF) that in
sequence occurs directly after the set time will be
activated first.
SET TEMPERATURE( C)
ECONOMY(SLEEP) operation
FAN
HIGH
MED
LOW
AUTO
COOL
DRY
HEAT
TEMP
ON/OFF FAN SPEED
MODE
SWING
ION
ECONOMY
RESET LOCK
TIMER ON
TIMER OFF
FOLLOW
LED
ME
DISPLAY TURBO
1
When you press the ECONOMY button, the
economic running function will be activated,
the set temperature will increase(cooling) or
decrease(heating) by 1oC(2oF) over the next
30 minutes and by another 1oC(2oF) after an
additional 30 minutes.This new temperature
will be maintained for 7 hours before it returns
to the originally selected temperature.(NOTE:
On some models, the set temperature will
increase (cooling) or decrease(heating) by
1oC(2oF) per hour for 2 hours. This new
temperature will be maintained for 5 hours ,
then the unit is off.)
NOTE: The ECONOMY/SLEEP function is only
available under Cooling, Heating and
AUTO operation.
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising