PG-D50X3D/D45X3D Operation-Manual Setup

PG-D50X3D/D45X3D Operation-Manual Setup
DATA PROJECTOR
MODEL
PG-D50X3D
PG-D45X3D
SETUP MANUAL
Connecting Pin Assignments .............................. 2
RS-232C Specifications and Commands ........... 4
Setting up the Projector Network Environment ... 9
1. Connecting the Projector to a Computer ...........10
2. Setting an IP Address for the Computer ............11
3. Setting up a Network Connection for the
Projector .......................................................13
Controlling the Projector via LAN ..................... 15
Controlling the Projector Using Internet Explorer
(Version 5.0 or later)......................................15
Confirming the Projector Status (Status) ................16
Controlling the Projector (Control) ..........................16
Setting and Adjusting the Projector
(Settings & Adjustments) ..............................17
Setting the Security (Network – Security) ...............17
Making General Settings for the Network
(Network – General) .....................................18
Setting for Sending E-mail when an Error Occurs
(Mail – Originator Settings) ..........................18
Setting Error Items and Destination Addresses
to which E-mail is to be Sent when an
Error Occurs (Mail – Recipient Settings) ......19
Setting Error Items and the URL that are to be
Displayed when an Error Occurs
(Service & Support – Access URL) ...............19
Setting up the Projector Using RS-232C or
Telnet .......................................................... 20
When Connecting Using RS-232C .........................20
When Connecting Using Telnet ..............................21
SETUP MENU (Main Menu) ....................................22
ADVANCED SETUP MENU ....................................22
View Setting Detail List ([V]View All Setting) ...........23
Set Items ................................................................23
Save Settings and Quit ([S]Save & Quit) .................24
Quit without Saving Settings ([Q]Quit Unchanged)...24
IP Address Setting ([1]IP Address) .........................25
Subnet Mask Setting ([2]Subnet Mask) ..................25
Default Gateway Setting ([3]Default Gateway) .......25
User Name Setting ([4]User Name) ........................25
Password Setting ([5]Password) .............................26
RS-232C Baud Rate Setting
([6]RS-232C Baud Rate) ...............................26
Projector Name Setting ([7]Projector Name) ..........26
DHCP Client Setting ([8]DHCP Client) ....................26
Disconnecting All Connections
([D]Disconnect All) ........................................27
Entering ADVANCED SETUP MENU
([A]Advanced Setup).....................................27
Setting Auto Logout Time
(ADVANCED[1]Auto Logout Time) ................27
Data Port Setting (ADVANCED[2]Data Port) ...........27
Carrying out Network Ping Test
(ADVANCED[5]Network Ping Test) ...............28
Setting of Accept IP Address (ADVANCED
[6]Accept IP Addr(1) – [8]Accept IP Addr(3)) ..28
Accepting All IP Addresses
(ADVANCED[9]Accept All IP Addr) ...............28
Setting of Search Port
(ADVANCED[0]Search Port)..........................29
Return to Default Settings
(ADVANCED[!]Restore Default Setting) ........29
Return to Main Menu
(ADVANCED[Q]Return to Main Menu) ..........29
Resetting the Lamp Timer of the Projector
via LAN ....................................................... 30
Troubleshooting .................................................. 32
Connecting Pin Assignments
COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals: mini
D-sub 15 pin female connector
11
15
COMPUTER Input/Output
Pin No.
Signal
1. Video input (red)
2. Video input (green/sync on green)
3. Video input (blue)
4. Not connected
5. Not connected
6. Earth (red)
7. Earth (green/sync on green)
8. Earth (blue)
9. Not connected
10. GND
11. Not connected
12. Bi-directional data
13. Horizontal sync signal: TTL level
14. Vertical sync signal: TTL level
15. Data clock
5
10
1
6
COMPUTER Input/Output
Pin No.
Signal
1. PR (CR)
2. Y
3. PB (CB)
4. Not connected
5. Not connected
6. Earth (PR)
7. Earth (Y)
8. Earth (PB)
9. Not connected
10. Not connected
11. Not connected
12. Not connected
13. Not connected
14. Not connected
15. Not connected
DVI-I Terminal: 29 pin connector
23
24
18
17
87
21
• DVI Digital Input
Pin No.
Signal
1. T.M.D.S data 2–
2. T.M.D.S data 2+
3. T.M.D.S data 2 shield
4. Not connected
5. Not connected
6. DDC clock
7. DDC data
8. Not connected
9. T.M.D.S data 1–
10. T.M.D.S data 1+
11. T.M.D.S data 1 shield
12. Not connected
13. Not connected
14. +5V power
15. Ground
C3
C5
C4
C2
C1
9
16
• DVI Analog RGB Input
Pin No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Signal
Not connected
Not connected
Not connected
Not connected
Not connected
DDC clock
DDC data
Vertical sync
Not connected
Not connected
Not connected
Not connected
Not connected
+5V power
Ground
Signal
Hot plug detection
T.M.D.S data 0–
T.M.D.S data 0+
T.M.D.S data 0 shield
Not connected
Not connected
T.M.D.S clock shield
T.M.D.S clock+
T.M.D.S clock–
Not connected
Not connected
Not connected
Not connected
Ground
• DVI Analog Component Input
Pin No.
Signal
Pin No.
16.
17.
18.
19.
20.
21.
22.
23.
24.
C1.
C2.
Hot plug detection
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Analog input Red
Analog input Green
(Sync On Green)
Analog input Blue
Horizontal sync
(Composite Sync)
Ground
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
C3.
C4.
C5.
-2
Pin No.
16.
17.
18.
19.
20.
21.
22.
23.
24.
C1.
C2.
C3.
C4.
C5.
Signal
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Ground
Pin No.
Signal
16.
17.
18.
19.
20.
21.
22.
23.
24.
C1.
C2.
C3.
C4.
C5.
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Analog input Pr/Cr
Analog input Y
Analog input Pb/Cb
Not connected
Ground
Connecting Pin Assignments
RS-232C Terminal: D-sub 9 pin male connector
1
5
6
Pin No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
9
Signal
Name
I/O
RD
SD
Receive Data
Send Data
Input
Output
SG
Signal Ground
RS
CS
Request to Send
Clear to Send
Reference
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
RS-232C Cable recommended connection: D-sub 9 pin female connector
5
9
1
6
Pin No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Signal
CD
RD
SD
ER
SG
DR
RS
CS
CI
Pin No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Signal
CD
RD
SD
ER
SG
DR
RS
CS
CI
Note
• Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
Projector
Pin No.
4
5
6
USB Terminal: Type B USB connector
4 3
Pin No.
1.
2.
3.
4.
Signal
VCC
USB–
USB+
SG
Computer
Pin No.
4
5
6
LAN Terminal: LAN (RJ-45)
Name
USB power
USB data–
USB data+
Signal Ground
Pin No.
1.
2.
3.
4.
Signal
TX+
TX–
RX+
Pin No.
5.
6.
7.
8.
Signal
RX–
8 ... 1
1 2
-3
RS-232C Specifications and Commands
Computer control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross
type, commercially available) to the projector. (See page 24 of the projector's operation manual for
connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Parity bit: None
Baud rate*: 9,600 bps / 38,400 bps / 115,200 bps
Stop bit: 1 bit
Data length: 8 bits
Flow control: None
*Set the projector's baud rate to the same rate as used by the computer.
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code.
After the projector processes the command from the computer, it sends a response code to the
computer.
Command format
C1
C2
C3
C4
Command 4-digit
P1
P2
P3
P4
Return code (0DH)
Parameter 4-digit
Response code format
Problem response (communication error or incorrect command)
Normal response
O
K
Return code (0DH)
E
R
R
Return code (0DH)
Info
• When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds
after the power has been turned on, and then transmit the commands.
• After sending an input selection or picture adjustment command and then receiving an “OK” response
code, the projector may take some time to process the command. If a second command is sent while the
projector is still processing the first command, you may receive an “ERR” response code. If this happens,
try resending the second command.
• When more than one code is being sent, send each command only after the response code for the
previous command from the projector is verified.
• “POWR????”, “TABN _ _ _ 1”, “TLPS _ _ _ 1”, “TPOW _ _ _ 1”, “TLPN _ _ _ 1”, “TLTT _ _ _ 1”,
“TLTM _ _ _ 1”, “TLTL _ _ _ 1”, “TNAM _ _ _ 1”, “MNRD _ _ _ 1”, “PJN0 _ _ _ 1”
− When the projector receives the special commands shown above:
* The on-screen display will not disappear.
* The “Auto Power Off” timer will not be reset.
− The special commands are available for applications that require continuous polling.
Note
• If an underbar (_) appears in the parameter column, enter a space.
• If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under
Control Contents.
PJLinkTM Compliant:
This product conforms with the PJLink standard Class 1 and all Class 1 commands are implemented.
This product confirms with the PJLink standard specification version 1.00.
For additional information, visit “http://pjlink.jbmia.or.jp/english/”.
-4
RS-232C Specifications and Commands
Commands
Example: When turning on the projector, make the following setting.
Compuer
P
O
W
R
_
_
_
Projector
→
←
1
O
K
RETURN
CONTROL CONTENTS
Power
COMMAND
P O W R _
P O W R _
On
Off
Status
Volume
Keystone
AV Mute
1 OK or ERR
OK
0 OK
OK or ERR
Status
T L P S _
_
_
1 0: Off, 1: On, 2: Retry
3: Waiting, 4: Lamp Error
0: Off, 4: Lamp Error
_
_
1 1: On, 2: Cooling
0: Standby
Quantity
T P O W _
T L P N _
_
_
1 1
Usage Time(Hour)
T L T T
_
_
_
1 0 – 9999(Integer)
Usage Time(Minute)
T L T M _
T L T L _
_
_
1 0, 15, 30, 45
0: Normal
1: Temp High
2: Fan Error
4: Cover Open
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
64: Temp Abnormally High
_
_
1 0% – 100%(Integer)
T N A M _
M N R D _
_
_
1 PGD50X3D/PGD45X3D
_
_
1 PG-D50X3D/PG-D45X3D
Projector Name Setting 1
(First 4 characters) *1
P J N 1
*
*
*
* OK or ERR
Projector Name Setting 2
(Middle 4 characters) *1
P J N 2
*
*
*
* OK or ERR
Projector Name Setting 3
(Last 4 characters) *1
P J N 3
*
*
*
* OK or ERR
Projector Name Check
P J N 0
_
_
_
1 Projector Name
Computer
I
_
_
1 OK or ERR
ERR
DVI
I
R G B _
R G B _
_
_
2 OK or ERR
ERR
B D S _
B D S _
B D S _
_
_
1 OK or ERR
ERR
_
_
2 OK or ERR
ERR
_
_
3 OK or ERR
ERR
_
_
1 OK or ERR
ERR
_
_
2 OK or ERR
ERR
Model Name Check
DVI-D-Computer select *2
I
DVI-D-Video select *2
I
DVI-Analog select *2
I
Video
I
V E D _
V E D _
Input RGB Check
I
R G B ? ? ? ? 1: Computer, 2: DVI or ERR
ERR
Input Video Check
I
V E D ? ? ? ? 1: S-Video, 2: Video or ERR
ERR
Input Mode Check
I M O D ? ? ? ? 1: RGB, 2: Video
ERR
Input Check
I
ERR
S-Video
I
Volume up/down(-10 – +10)
C H K ? ? ? ? 1: Computer
2: DVI
3: S-Video
4: Video
_
_
V O L A
* * OK or ERR
V O U D _ * * * OK or ERR
-80 – +80
K E Y S
Volume(0 – 60)
*
I M B K _
I M B K _
F R E Z _
F R E Z _
On
Off
Freeze
_
_
Power Status
Model Name Check
Input Change
_
_
0
Life(Percentage)
Name
Standby mode
(or 30-second startup time)
Power ON
P O W R ? ? ? ? 1
T A B N _ _ _ 1 0: Normal
1: Temp High
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
Projector Condition
Lamp
PARAMETER
On
Off
Auto Sync
Start
Resize
Computer
Normal
Stretch
Dot By Dot
Full
Border
Area Zoom
V-Stretch
DVI
Normal
Stretch
Dot By Dot
Full
Border
Area Zoom
V-Stretch
S-Video
Normal
Stretch
Border
Area Zoom
V-Stretch
A D J S _
R A S R _
R A S R _
* OK or ERR
ERR
ERR
*
_
*
_
ERR
1 OK or ERR
ERR
_
_
0 OK or ERR
ERR
_
_
1 OK or ERR
ERR
_
_
0 OK or ERR
ERR
_
_
1 OK or ERR
ERR
_
_
1 OK or ERR
ERR
_
_
2 OK or ERR
ERR
R A S R _
R A S R _
_
_
3 OK or ERR
ERR
_
_
5 OK or ERR
ERR
R A S R _
R A S R _
_
_
6 OK or ERR
ERR
_
1 0 OK or ERR
ERR
R A S R _
R B S R _
R B S R _
_
ERR
_
1 1 OK or ERR
_ 1 OK or ERR
_ 2 OK or ERR
R B S R _
R B S R _
_
_
3 OK or ERR
ERR
_
_
5 OK or ERR
ERR
R B S R _
R B S R _
R B S R _
R A S V _
R A S V _
R A S V _
R A S V _
R A S V _
_
ERR
ERR
_
_
6 OK or ERR
ERR
_
1 0 OK or ERR
ERR
_
1 1 OK or ERR
_ 1 OK or ERR
_ 2 OK or ERR
ERR
_
_
ERR
ERR
_
_
3 OK or ERR
ERR
_
1 0 OK or ERR
ERR
_
1 1 OK or ERR
ERR
-5
RS-232C Specifications and Commands
RETURN
CONTROL CONTENTS
Resize
Video
COMMAND
Normal
Stretch
Border
Area Zoom
V-Stretch
ALL Reset
Computer INPUT
Picture Mode
Standard
Presentation
Movie
Game
sRGB
1 OK or ERR
ERR
_
_
2 OK or ERR
ERR
_
_
3 OK or ERR
ERR
1 0 OK or ERR
ERR
R B S V _
A L R E _
_
1 1 OK or ERR
_ 1 OK or ERR
ERR
_
_
1 0 OK or ERR
ERR
ERR
_
1 1 OK or ERR
ERR
_
1 2 OK or ERR
ERR
_
1 3 OK or ERR
ERR
R A P S _
R A P I _
_
1 4 OK or ERR
ERR
*
*
* OK or ERR
ERR
R A B R _
R A R D _
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
ERR
-30 – +30
-30 – +30
Red
-30 – +30
Blue
-30 – +30
Color
-30 – +30
R A B E _
R A C O _
Tint
-30 – +30
R A T
_
*
*
* OK or ERR
Sharp
-30 – +30
* OK or ERR
ERR
-1 – +1
*
_
*
CLR Temp
R A S H _
R A C T _
* OK or ERR
ERR
R A W E _
I P _
_
*
_
* OK or ERR
ERR
_
_
0 OK or ERR
ERR
I
BrilliantColor™
0 – +2
Progressive
2D Progressive
R A
3D Progressive
Level 2
P _
P _
R A N R _
R A N R _
R A N R _
Auto
R A R E _
I A S I _
_
_
0 OK or ERR
ERR
RGB
I
A S
_
_
_
1 OK or ERR
ERR
Off
Level 1
Picture Reset
Signal Type
Audio Input
Picture Mode
R A
I
_
_
1 OK or ERR
ERR
R A
I
_
_
2 OK or ERR
ERR
I
_
_
0 OK or ERR
ERR
_
_
1 OK or ERR
ERR
_
_
2 OK or ERR
ERR
_
_
1 OK or ERR
ERR
Component
I
A S
I
_
_
_
2 OK or ERR
ERR
Audio 1
R A A
I
_
_
_
1 OK or ERR
ERR
Audio 2
R A A I _
R B P S _
R B P S _
_
_
2 OK or ERR
ERR
_
1 0 OK or ERR
ERR
Standard
Presentation
Movie
Game
sRGB
Contrast
-30 – +30
Bright
-30 – +30
Red
-30 – +30
R B P S _
R B P S _
_
1 1 OK or ERR
ERR
_
1 2 OK or ERR
ERR
_
1 3 OK or ERR
ERR
R B P S _
R B P I _
_
1 4 OK or ERR
ERR
*
*
* OK or ERR
ERR
R B B R _
R B R D _
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
*
* OK or ERR
ERR
_
*
_
* OK or ERR
ERR
R B W E _
I P _
_
*
_
* OK or ERR
ERR
_
_
0 OK or ERR
ERR
Blue
-30 – +30
Color
-30 – +30
Tint
-30 – +30
Sharp
-30 – +30
R B B E _
R B C O _
R B T I _
R B S H _
CLR Temp
-1 – +1
R B C T
BrilliantColor™
0 – +2
Progressive
2D Progressive
R B
3D Progressive
Level 2
P _
P _
R B N R _
R B N R _
R B N R _
Auto
R B R E _
I B S I _
_
_
0 OK or ERR
ERR
RGB
I
B S
_
_
_
1 OK or ERR
ERR
Film Mode
DNR
Off
Level 1
Picture Reset
Signal Type
R B
I
_
_
1 OK or ERR
ERR
R B
I
_
_
2 OK or ERR
ERR
I
_
_
0 OK or ERR
ERR
_
_
1 OK or ERR
ERR
_
_
2 OK or ERR
ERR
_
_
1 OK or ERR
ERR
Component
I
B S
I
_
_
_
2 OK or ERR
ERR
Audio Input
Audio 1
R B A
I
_
_
_
1 OK or ERR
ERR
Audio 2
_
2 OK or ERR
ERR
Auto
R B A I _
H M B D _
H M B D _
_
Dynamic
Range
_
_
0 OK or ERR
ERR
_
_
1 OK or ERR
ERR
_
2 OK or ERR
ERR
Standard
H M B D _
V A P S _
_
Picture Mode
_
1 0 OK or ERR
ERR
V A P S _
V A P S _
_
1 1 OK or ERR
ERR
_
1 2 OK or ERR
ERR
Standard
Enhanced
Presentation
Movie
V A P S _
I _
_
1 3 OK or ERR
ERR
-30 – +30
V A P
*
*
* OK or ERR
ERR
Bright
-30 – +30
*
* OK or ERR
ERR
-30 – +30
V A B R _
V A R D _
*
Red
*
*
* OK or ERR
ERR
Blue
-30 – +30
V A B E _
*
*
* OK or ERR
ERR
Game
Contrast
-6
_
R A P S _
R A P S _
_
Bright
DNR
S-Video INPUT
Standby mode
(or 30-second startup time)
R B S V _
R B S V _
R B S V _
R B S V _
R A P S _
R A P S _
_
Power ON
Contrast
Film Mode
DVI INPUT
PARAMETER
RS-232C Specifications and Commands
RETURN
CONTROL CONTENTS
S-Video INPUT
COMMAND
Color
-30 – +30
Tint
-30 – +30
Sharp
-30 – +30
CLR Temp
-1 – +1
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
*
_
*
* OK or ERR
ERR
* OK or ERR
ERR
_
*
_
* OK or ERR
ERR
_
_
0 OK or ERR
ERR
0 – +2
2D Progressive
V A
3D Progressive
Level 2
P _
P _
V A N R _
V A N R _
V A N R _
_
_
2 OK or ERR
ERR
_
_
1 OK or ERR
ERR
_
_
1 OK or ERR
ERR
_
2 OK or ERR
ERR
Off
Level 1
Audio Input
Picture Mode
V A
I
_
_
1 OK or ERR
ERR
V A
I
_
_
2 OK or ERR
ERR
_
_
0 OK or ERR
ERR
_
_
1 OK or ERR
ERR
Audio 1
V A R E _
V A A I _
Audio 2
V A A
_
_
Standard
V B P S _
V B P S _
_
1 0 OK or ERR
ERR
_
1 1 OK or ERR
ERR
Picture Reset
Presentation
Movie
Game
Contrast
-30 – +30
Bright
-30 – +30
Red
-30 – +30
Blue
-30 – +30
Color
I
V B P S _
V B P S _
V B P I _
_
1 2 OK or ERR
ERR
_
1 3 OK or ERR
ERR
*
*
* OK or ERR
ERR
V B B R _
V B R D _
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
-30 – +30
V B B E _
V B C O _
*
*
* OK or ERR
ERR
Tint
-30 – +30
V B T
_
*
*
* OK or ERR
ERR
Sharp
-30 – +30
* OK or ERR
ERR
-1 – +1
*
_
*
CLR Temp
V B S H _
V B C T _
* OK or ERR
ERR
V B W E _
I P _
_
*
_
* OK or ERR
ERR
_
_
0 OK or ERR
ERR
P _
P _
_
_
1 OK or ERR
ERR
_
_
2 OK or ERR
ERR
BrilliantColor™
0 – +2
Progressive
2D Progressive
DNR
V B
I
V B
I
Off
Level 2
V B N R _
V B N R _
V B N R _
ERR
ERR
_
2 OK or ERR
ERR
_
_
1 OK or ERR
ERR
_
_
1 OK or ERR
ERR
V B A
_
_
_
2 OK or ERR
ERR
_
1 1 OK or ERR
ERR
_
0 0 OK or ERR
ERR
Red
C M C S _
C M C S _
C M H R _
Green
Cyan
Blue
Magenta
Reset
Red
Yellow
Green
Cyan
Blue
Magenta
Reset
Red
Yellow
Green
Cyan
Blue
Magenta
I
*
*
* OK or ERR
ERR
C M H Y _
C M H G _
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
C M H C _
C M H B _
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
C M H M _
C M R E _
*
_
*
_
* OK or ERR
ERR
2 OK or ERR
ERR
C M S R _
C M S Y _
C M S G _
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
C M S C _
C M S B _
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
C M S M _
C M R E _
*
_
*
_
* OK or ERR
ERR
3 OK or ERR
ERR
C M V R _
C M V Y _
C M V G _
C M V C _
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
C M V B _
C M V M _
*
*
* OK or ERR
ERR
*
_
*
_
* OK or ERR
ERR
4 OK or ERR
ERR
_
_
1 OK or ERR
ERR
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
*
*
* OK or ERR
ERR
C.M.S. All Reset
C M R E _
C M R E _
Clock
-150 – +150
I
Phase
-30 – +30
I
*
N P H _
H-position
-150 – +150
I
A H P
V-position
-60 – +60
Reset
Fine Sync Adjustment Reset
0 OK or ERR
1 OK or ERR
_
Audio 1
Yellow
Value
_
_
Audio 2
On
Saturation
_
_
V B R E _
V B A I _
Off
Hue
V B
3D Progressive
Picture Reset
Audio Input
I
Film Mode
Level 1
C.M.S.
V A W E _
I P _
Standby mode
(or 30-second startup time)
BrilliantColor™
DNR
C.M.S. Setting
V A C O _
V A T I _
V A S H _
V A C T _
Power ON
Progressive
Film Mode
Video INPUT
PARAMETER
N C L
*
I A V P _
I A R E _
L N D S _
O V S N _
*
_
*
_
* OK or ERR
ERR
1 OK or ERR
ERR
*
_
*
_
* OK or ERR
ERR
1 OK or ERR
ERR
Image Shift
-96 – +96
Overscan
On
_
0 OK or ERR
ERR
On
O V S N _
I M D I _
_
OSD Display
_
_
1 OK or ERR
ERR
Off
I M D
_
_
_
0 OK or ERR
ERR
Off
I
-7
RS-232C Specifications and Commands
RETURN
CONTROL CONTENTS
Video System
COMMAND
M E S Y _
M E S Y _
M E S Y _
M E S Y _
Auto
PAL
SECAM
NTSC4.43
M E S Y _
M E S Y _
M E S Y _
NTSC3.58
PAL-M
PAL-N
M E S Y _
I M B G _
PAL-60
Background
PARAMETER
Logo
I M B G _
I M B G _
Blue
None
_
Power ON
Standby mode
(or 30-second startup time)
_
1 OK or ERR
ERR
2 OK or ERR
ERR
_
_
_
_
3 OK or ERR
ERR
_
_
4 OK or ERR
ERR
_
_
5 OK or ERR
ERR
_
_
6 OK or ERR
ERR
_
_
7 OK or ERR
ERR
_
_
8 OK or ERR
ERR
_
_
1 OK or ERR
ERR
_
_
3 OK or ERR
ERR
_
_
4 OK or ERR
ERR
_
_
1 OK or ERR
ERR
_
_
0 OK or ERR
ERR
_
1 OK or ERR
ERR
Off
T H M D _
T H M D _
Auto Sync
On
A A D J
_
_
Off
_
0 OK or ERR
ERR
On
A A D J _
A P O W _
A P O W _
_
Auto Power Off
_
_
1 OK or ERR
ERR
Auto Restart
On
STANDBY Mode
PRJ Mode
Reverse
Eco+Quiet
On
Off
_
_
0 OK or ERR
ERR
_
_
_
1 OK or ERR
ERR
M O U T
_
_
_
0 OK or ERR
ERR
_
_
1 OK or ERR
ERR
Off
I M R E _
I M R E _
_
_
0 OK or ERR
ERR
On
I M I
_
_
1 OK or ERR
ERR
English
Deutsch
Español
Nederlands
Français
On
_
_
2 OK or ERR
ERR
_
_
3 OK or ERR
ERR
_
_
4 OK or ERR
ERR
_
_
5 OK or ERR
ERR
6 OK or ERR
ERR
7 OK or ERR
ERR
_
8 OK or ERR
ERR
M E L A _
M E L A _
_
_
9 OK or ERR
ERR
_
1 0 OK or ERR
ERR
M E L A _
M E L A _
_
1 1 OK or ERR
ERR
_
1 2 OK or ERR
ERR
M E L A _
M E L A _
_
1 3 OK or ERR
ERR
_
1 4 OK or ERR
ERR
M E L A _
M E L A _
_
1 5 OK or ERR
ERR
_
1 6 OK or ERR
ERR
M E L A _
S S N D _
_
ERR
_
FAO
S S N D _
A O U T _
1 7 OK or ERR
_ 1 OK or ERR
_ 0 OK or ERR
_
_
1 OK or ERR
ERR
VAO
A O U T
_
_
_
2 OK or ERR
ERR
On
A S P K _
A S P K _
T F R Q _
_
_
1 OK or ERR
ERR
_
_
0 OK or ERR
ERR
On
Off
Horizontal
Vertical
Normal
High
Balance
-30 − +30
Treble
-30 − +30
Bass
-30 − +30
_
ERR
ERR
_
_
1 kHz(***.* or ERR)
ERR
T F R Q _
H L M D _
_
_
2 Hz(***.* or ERR)
ERR
_
_
0 OK or ERR
ERR
H L M D _
A A B L _
_
_
1 OK or ERR
ERR
*
*
* OK or ERR
ERR
A A T E _
A A B A _
*
*
* OK or ERR
ERR
*
_
*
_
* OK or ERR
ERR
1 OK or ERR
ERR
A A R E _
Audio Adjustment Reset
Off
3 D E N _
_
_
0 OK or ERR
ERR
On
3 D E N _
_
_
1 OK or ERR
ERR
3 D
I
V _
_
_
1 OK or ERR
ERR
V
I
S U _
_
_
0 OK or ERR
ERR
7.5 IRE
V
I
S U _
_
_
1 OK or ERR
ERR
Off
C L C A _
_
_
0 OK or ERR
ERR
CC1
C L C A _
_
_
1 OK or ERR
ERR
CC2
C L C A _
_
_
2 OK or ERR
ERR
DLP® LinkTM Invert
Lamp Timer Reset *3
ERR
ERR
_
Off
Closed Caption
(For Americas only)
0 OK or ERR
1 OK or ERR
_
Magyar
Video Setup
M E L A _
M E L A _
_
_
_
Türkçe
DLP ® LinkTM
M E L A _
M E L A _
_
_
_
polski
Fan Mode
I M I
M E L A _
M E L A _
_
Português
RGB Frequency Check
N _
N _
M E L A _
M E L A _
Italiano
Svenska
Internal Speaker
ERR
ERR
M O U T
Off
Audio Out
0 OK or ERR
1 OK or ERR
Off
Invert
System Sound
_
_
Standard
Eco
Language
_
_
A R E S _
A R E S _
0 IRE
L P R E 0 0 0 1 ERR
OK or ERR
*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.
*2 This command should be sent only after the “IRGB _ _ _ 2” command is sent and an “OK” response code is
received.
*3 The Lamp Timer Reset command is available only in standby mode.
-8
Setting up the Projector Network Environment
This section describes the basic procedure for using the projector via the network.
If the network is already constructed, the projector's network settings may need to be
changed. Please consult your network administrator for assistance with these settings.
You can make network settings both on the projector and on the computer. The following
procedure is for making settings on the computer.
Network settings on the computer
1. Connecting the projector to a computer
Connect a LAN cable (Category 5, cross-over type) between the computer and projector.
LAN cable
(commercially available)
Page 10
2. Setting an IP address for the computer
Adjust the IP settings of the computer to enable one-to-one communications with the projector.
Temporarily change
the computer's IP
address.
Pages 11, 12
3. Setting up a network connection for the projector
Adjust the projector network settings to conform to your network.
Use Internet Explorer
(version 5.0 or later)
to make various
projector settings.
Pages 13, 14
• Microsoft®, Windows® and Windows Vista®are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
• PJLink is a registered trademark or an application trademark in Japan, the United States, Canada, E.U.,
China and/or other countries/regions.
• All other company or product names are trademarks or registered trademarks of their respective
companies.
-9
Setting up the Projector Network Environment
1. Connecting the Projector
to a Computer
Establishing a one-to-one connection from
the projector to a computer. Using a
commercially available LAN cable (UTP
cable, Category 5, cross-over type) you can
configure the projector via the computer.
1
Disconnect the computer's LAN
cable from the existing network.
A LAN cable being
connected to the network
2
Connect a commercially available
LAN cable (UTP cable, Category 5,
cross-over type) to the projector's
LAN terminal and connect the
other end of the cable to the
computer's LAN terminal.
LAN cable
(cross-over type, commercially available)
3
Plug the power cord into the AC
socket of the projector.
4
Turn on the computer.
ON
Info
Confirm that the LINK LED on the rear of the
projector illuminates. If the LINK LED does not
illuminate, check the following:
• The LAN cable is properly connected.
• The power switches of both the projector and
the computer are on.
This completes the connection. Now proceed to “2. Setting an IP Address for the Computer”.
-10
Setting up the Projector Network Environment
2. Setting an IP Address for
the Computer
The following describes how to make
settings in Windows Vista®.
1
Log on the network using the
administrator's account for the
computer.
2
Click “start”, and click “Control
Panel”.
2
1
3
Click “View network status and
tasks” of “Network and Internet”,
and click “View status” in the new
window.
• This manual uses examples to explain the
operations in Category View. If you are using
Classic View, double-click “Network and
Sharing Center”.
1
XXXXXXXXX
2
4
Click “Properties”.
• When the user account control display is
displayed, click “Continue”.
1
-11
Setting up the Projector Network Environment
5
Click “Internet Protocol Version 4
(TCP/IPv4)”, and click the
“Properties” button.
1
2
6
Confirm or change an IP address
for the setup computer.
1 Confirm and note the current IP
address, Subnet mask and Default
gateway.
Make sure to note the current IP address,
Subnet mask and Default gateway as you
will be required to reset them later.
2 Set temporarily as follows:
IP address: 192.168.150.3
Subnet mask: 255.255.255.0
Default gateway: (Do not input any
values.)
Note
• The factory default settings for the projector are
as follows:
DHCP Client: OFF
IP address: 192.168.150.2
Subnet mask: 255.255.255.0
Default gateway: 0.0.0.0
7
After setting, click the “OK”
button, and then restart the
computer.
After confirming or setting, proceed to “3. Setting up Network Connection for the Projector”.
-12
Setting up the Projector Network Environment
3. Setting up a Network Connection for the Projector
Settings for such items as the projector's
IP address and subnet mask are
compatible with the existing network.
Set each item on the projector as follows.
(See page 50 of the projector's operation
manual for setting.)
DHCP Client: Off
IP Address: 192.168.150.002
Subnet Mask: 255.255.255.000
1
Start Internet Explorer (version 5.0
or later) on the computer, and
enter “http://192.168.150.2/” in
“Address”, and then press the
“Enter” key.
2
If a user name and a password
have not yet been set, just click
the “OK” button.
• If a user name and a password have been
set, input the user name and the password,
and click the “OK” button.
• If the user name or password is entered
incorrectly three times, an error message will
be displayed.
• When you are using Internet Explorer 7, other
setup screen may be displayed. In this case,
make the proper adjustments for the setup
screen.
3
When the screen as shown on the
right appears, click “TCP/IP”.
-13
Setting up the Projector Network Environment
4
The TCP/IP setting screen
appears, ready for network
settings for the projector.
Items
Setting example / Remarks
New
You can set the password to protect
Password the TCP/IP setting.
DHCP
Client
Select “ON” or “OFF” to determine
whether to use DHCP Client.
IP
Address
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting: 192.168.150.2
Enter an IP address appropriate for
the network.
Subnet
Mask
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting:
255.255.255.0
Set the subnet mask to the same as
that of the computer and equipment
on the network.
Default
Gateway
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting: 0.0.0.0
* When not in use, set to “0.0.0.0”.
DNS
Server
Factory default setting: 0.0.0.0
* When not in use, set to “0.0.0.0”.
Note
• Confirm the existing network's segment (IP
address group) to avoid setting an IP address
that duplicates the IP addresses of other
network equipment or computers. If
“192.168.150.2” is not used in the network
having an IP address of “192.168.150.XXX”, you
don't have to change the projector IP address.
• For details about each setting, consult your
network administrator.
•
•
•
•
5
Click the “Apply” button.
6
The set values appear. Confirm
that the values are set properly,
and then click the “Confirm”
button.
Close the browser.
This completes the network settings.
After setting items, wait for about 15 seconds and then re-access.
Change the IP address of the setting computer back to its original address, which you have noted down in
Step 6-1 on page 12, and then connect the computer and the projector to the network.
-14
Controlling the Projector via LAN
After connecting the projector to your network, enter the projector IP address in
“Address” on Internet Explorer (version 5.0 or later) using a computer on the network to
start a setup screen that will enable control of the projector via the network.
Controlling the Projector
Using Internet Explorer
(Version 5.0 or later)
Complete connections to external
equipment before starting the operation.
(See pages 21-25 of the projector's
operation manual.)
Complete the AC cord connection. (See
page 25 of the projector's operation
manual.)
Note
• When connecting the projector to the LAN, use
a commercially available LAN cable (UTP cable,
Category 5, cross-over type). When
connecting the projector to a hub, use a
straight-through cable.
1
Start Internet Explorer (version 5.0
or later) on the computer.
2
Enter “http://” followed by the
projector IP address set by the
procedure on page 14 followed by
“/” in “Address”, and then press
the “Enter” key.
• When “DHCP Client” is set to “OFF” on the
projector, IP address is 192.168.150.2. If you
did not change the IP address in “3. Setting
up a Network Connection for the
Projector” (pages 13-14), enter
“http://192.168.150.2/”.
3
A screen for controlling the
projector appears, ready for
performing various status
conditions, control, and settings.
-15
Controlling the Projector via LAN
Confirming the Projector
Status (Status)
Controlling the Projector
(Control)
On this screen, you can perform projector
control. You can control the following
items:
On this screen, you can confirm the
projector status. You can confirm the
following items:
• MAC Address
• Power
• Condition
• Lamp Timer
• Lamp Life
• Input
• Signal Info
• Serial Number
Note
• If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be
displayed. Wait for a moment and then operate
again.
• For details about each item, refer to the
projector's operation manual.
-16
• Power
• Input Select
• Volume
• AV Mute
Note
• If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be
displayed. Wait for a moment and then operate
again.
• You cannot operate this page while the
projector is warming up.
• While the projector is in standby mode, you can
only control “Power ON”.
• For details about each item, refer to the
projector's operation manual.
Controlling the Projector via LAN
Setting and Adjusting the
Projector (Settings & Adjustments)
Setting the Security
(Network – Security)
Example: “Picture” screen display for COMPUTER
On these screens, you can make projector
settings or adjustments. You can set or
adjust the following items:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Picture Mode
CLR Temp
BrilliantColorTM
Progressive
DNR
Eco + Quiet Mode
Resolution Setting
Signal Type
Video System
Dynamic Range
Resize
Overscan
OSD Display
Background
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Projection Mode
DLP® LinkTM
DLP® LinkTM Invert
Video Setup
OSD Language
Auto Sync
Auto Power Off
Auto Restart
System Sound
Audio Out
Internal Speaker
Audio Input
RS-232C Speed
Fan Mode
All Reset
On this screen, you can make settings
relating to security.
Items
Description
User Name
Setting of user name for security
protection.
Password
Setting of password for security
protection.
Accept IP
Address
It is possible to set up to three IP
addresses allowing connection to the
projector.
All IP
Addresses
No limits are set to IP addresses
connecting to the projector.
From only
specific IP
addresses
For security improvement, only an IP
address set by “Address 1-3” can be
connected to the projector.
Note
• User Name and Password can be up to 8
characters.
• You can input the characters below:
a-z, A-Z, 0-9, -, _
Note
• If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be
displayed. Wait for a moment and then operate
again.
• You cannot operate this page while the
projector is warming up.
• For details about each item, refer to the
projector's operation manual.
-17
Controlling the Projector via LAN
Making General Settings for
the Network (Network - General)
Setting for Sending E-mail
when an Error Occurs
(Mail – Originator Settings)
On this screen, you can make general
settings relating to the network.
Items
Description
Projector
Name
Setting the projector name.
Auto Logout
Time
Setting the time interval in which the
projector will be automatically
disconnected from the network in units
of a minute (from 1 to 65535 minutes).
If the set value is made 0, the Auto
Logout function is disabled.
Data Port
Setting the TCP port number used
when exchanging data with the
projector (from 1025 to 65535).
Search Port
Setting the port number used when
searching for the projector (from 1025
to 65535).
After clicking the “Apply” button, the set
values appear. Confirm that the values are
set properly, and then click the “Confirm”
button.
Note
• After setting items, wait for about 15 seconds
and then re-access.
• Projector Name can be up to 12 characters.
• You can input the characters below:
A-Z, 0-9, -, _, (,), space
(When “a-z” are input, they are converted to
“A-Z” automatically.)
-18
On this screen, you can make settings for
sending e-mail to report when the
projector has generated an error.
Items
Setting example / Remarks
SMTP Server
Setting an SMTP server address for email transmission.
e.g.1: 192.168.150.253
e.g.2: smtp123.sharp.co.jp
* When using a domain name, make
settings for the DNS server.
Originator Email Address
Setting the projector's e-mail address.
The e-mail address set here becomes
Originator E-mail Address.
Originator
Name
Setting the sender's name. The name
set here appears in the “Originator
Name” column of the body of the
message.
Note
• SMTP Server, Originator E-mail Address and
Originator Name can be up to 64 characters.
• You can input the characters below:
SMTP Server and Originator E-mail Address:
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |, },
~, _, ', ., @, `
(You can input “@” only one time for “Originator
E-mail Address”.)
Originator Name : a-z, A-Z, 0-9, -, _, (,), space
• If the settings of “3. Setting up a Network
Connection for the Projector” on pages 13
and 14 are incorrectly set, e-mail will not be
sent.
Controlling the Projector via LAN
Setting Error Items and
Destination Addresses to
which E-mail is to be Sent
when an Error Occurs
Setting Error Items and the
URL that are to be
Displayed when an Error
Occurs (Service & Support –
(Mail – Recipient Settings)
Access URL)
On this screen, you can input e-mail
destinations to which error notification
(error items) e-mails are sent.
On this screen, you can make settings of
the URL and error items that are to be
displayed when the projector has
generated an error.
Items
E-mail
Address
Description
Set addresses to which error
notification e-mail is sent. You can set
up to five addresses.
Error e-mail is sent on the error items
Error Mail
(Lamp, Temp, checked in their check boxes.
Fan,Cover)
Test
Send test e-mail. This allows you to
confirm that the settings for e-mail
transmission are properly set.
Note
• E-mail Address can be up to 64 characters.
• You can input the characters below:
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |, },
~, _, ', ., @, `
(You can input “@” only one time.)
• For details about error items, refer to the
projector's operation manual.
Items
Description
Access URL
Set the URL that is to be displayed
when an error occurs. You can set up
to five addresses.
Condition
(Always,
Lamp, Temp,
Fan,Cover)
The URL is displayed when an error
checked in their check boxes occurs.
Test
The set URL site is test-displayed. This
allows you to confirm that the URL site
is properly displayed.
Example of the display when an error
occurs
-19
Setting up the Projector Using RS-232C or Telnet
Connect the projector to a computer using RS-232C or Telnet, and open the SETUP
MENU on the computer to carry out various settings for the projector.
When Connecting Using
RS-232C
1
Launch general purpose terminal
emulator.
2
Input settings for the RS-232C
port of the terminal emulator as
follows.
Baud Rate
Data Length
Parity Bit
Stop Bit
Flow Control
: 9600 bps*
: 8 bit
: None
: 1 bit
: None
* This is the factory default setting. If the value
of Baud Rate for the projector has been
changed, set Baud Rate here according to
the changed value on the projector.
3
Input “PJS11234” and press the
“Enter” key.
4
“OK” is displayed. Input
“PJS25678” and press the “Enter”
key within 10 seconds.
5
“User Name:” is displayed. Input
the user name and press the
“Enter” key.
• If a user name has not yet been set, just
press the “Enter” key.
6
“Password:” is displayed. Input
the password and press the
“Enter” key.
• If a password has not yet been set, just press
the “Enter” key.
-20
7
Input “setup” and press the
“Enter” key.
• SETUP MENU will be displayed.
▼SETUP MENU
-----------------------------SETUP MENU---------------------------[1]IP Address
[2]Subnet Mask
[3]Default Gateway
[4]User Name
[5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup
[D]Disconnect All
[V]View All Setting
[S]Save & Quit
[Q]Quit Unchanged
setup>
Note
• User name and password are not set in the
factory default settings.
• If the user name or password is entered
incorrectly three times, SETUP MENU will be
quit.
Setting up the Projector Using RS-232C or Telnet
▼SETUP MENU
When Connecting Using
Telnet
1
Click “Start” from the Windows®
desktop and select “Run”.
2
Enter “telnet 192.168.150.2” in the
text box that opens up. (If the IP
address of the projector is
192.168.150.2.)
3
Click the “OK” button.
4
“User Name:” is displayed. Input
the user name and press the
“Enter” key.
-----------------------------SETUP MENU---------------------------[1]IP Address
[2]Subnet Mask
[3]Default Gateway
[4]User Name
[5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup
[D]Disconnect All
[V]View All Setting
[S]Save & Quit
[Q]Quit Unchanged
setup>
Note
• If the IP address has been changed, be sure to
enter the new IP address in step 2.
• User name and password are not set in the
factory default settings.
• If the user name or password is entered
incorrectly three times in steps 4 or 5, SETUP
MENU will be quit.
• If a user name has not yet been set, just
press the “Enter” key.
5
“Password:” is displayed. Input
the password and press the
“Enter” key.
• If a password has not yet been set, just press
the “Enter” key.
6
Input “setup” and press the
“Enter” key.
• SETUP MENU will be displayed.
-21
Setting up the Projector Using RS-232C or Telnet
SETUP MENU
(Main Menu)
▼SETUP MENU
-----------------------------SETUP MENU---------------------------[1]IP Address
[2]Subnet Mask
[3]Default Gateway
[4]User Name
[5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup
[D]Disconnect All
[V]View All Setting
[S]Save & Quit
[Q]Quit Unchanged
setup>
[1] IP Address
IP address settings. (Page 25)
[2] Subnet Mask
Subnet mask settings. (Page 25)
[3] Default Gateway
Default gateway settings. (Page 25)
[4] User Name (Factory default setting: Not
Required)
Setting of user name for security protection.
(Page 25)
[5] Password (Factory default setting: Not
Required)
Setting of password for security protection.
(Page 26)
[6] RS-232C Baud Rate (Factory default setting:
9600 bps)
Baud rate settings for the RS-232C terminals.
(Page 26)
[7] Projector Name
It is possible to assign a projector name. (Page 26)
[8] DHCP Client
DHCP Client settings. (Page 26)
[A] Advanced Setup
Enters ADVANCED SETUP MENU. (Page 27)
[D] Disconnect All
Disconnect all connections. (Page 27)
[V] View All Setting
Displays all setting values. (Page 23)
Can also be used with ADVANCED SETUP
MENU.
[S] Save & Quit
Save set values and quit menu. (Page 24)
[Q] Quit Unchanged
Quit menu without saving setting values. (Page 24)
Note
• When “DHCP Client” is set to “OFF” on the
projector:
IP address: 192.168.150.2
Subnet mask: 255.255.255.0
Default gateway: 0.0.0.0
-22
ADVANCED SETUP MENU
▼ADVANCED SETUP MENU
********************** ADVANCED SETUP MENU ***************************
[1]Auto Logout Time [2]Data Port
[5]Network Ping Test
[6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3)
[9]Accept All IP Addr [0]Search Port
[!]Restore Default Setting
[Q]Return to Main Menu
advanced>
[1] Auto Logout Time (Factory default setting:
5 minutes)
Setting of time until automatic disconnection of
network connection. (Page 27)
[2] Data Port (Factory default setting: 10002)
Setting the TCP port number used when
exchanging data. (Page 27)
[5] Network Ping Test
It is possible to confirm that a network
connection between the projector and a
computer etc. is working normally. (Page 28)
[6] Accept IP Addr(1)
[7] Accept IP Addr(2)
[8] Accept IP Addr(3)
[9] Accept All IP Addr (Factory default setting:
Accept All)
For improved security, it is possible to set up
to three IP addresses allowing connection to
the projector.
Set IP addresses can be cancelled using [9]
Accept All IP Addr. (Page 28)
[0] Search Port (Factory default setting: 5006)
Setting the port number used when searching
for the projector. (Page 29)
[!] Restore Default Setting
Restores all setting values that can be set
using the menu to the default state. (Page 29)
[Q] Return to Main Menu
Return to the main SETUP MENU. (Page 29)
Setting up the Projector Using RS-232C or Telnet
Enter number or symbol of item to be selected on the SETUP MENU. When setting, input
the details to be set. Setting is carried out one item at a time, and saved at the end.
Set Items
View Setting Detail List
([V]View All Setting)
Example: When setting IP Address (change
from 192.168.150.2 to 192.168.150.3)
▼SETUP MENU
▼SETUP MENU
-----------------------------SETUP MENU---------------------------[1]IP Address
[2]Subnet Mask
[3]Default Gateway
[4]User Name
[5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup
[D]Disconnect All
[V]View All Setting
[S]Save & Quit
[Q]Quit Unchanged
setup>v
Model Name
: XX-XXXX
Projector Name
: XX-XXXX
MAC Address
: XX:XX:XX:XX:XX:XX
DHCP Client
: Disable
IP Address
: 192.168.150.2
Subnet Mask
: 255.255.255.0
Default Gateway
: Not Used
RS-232 Baud Rate : 9600 bps
Password
: Not Required
**********(Advanced Status)**********
Data Port
: 10002
Accept IP Address : Accept All
Auto Logout Time : 5 minutes
Search Port
: 5006
1 Enter “v” and press the “Enter” key.
Display all setting values(*).
1
*
-----------------------------SETUP MENU---------------------------[1]IP Address
[2]Subnet Mask
[3]Default Gateway
[4]User Name
[5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup
[D]Disconnect All
[V]View All Setting
[S]Save & Quit
[Q]Quit Unchanged
setup>1
IP Address
: 192.168.150.2
Please Enter
: 192.168.150.3
—> 192.168.150.3
(change)
-----------------------------SETUP MENU---------------------------[1]IP Address
[2]Subnet Mask
[3]Default Gateway
[4]User Name
[5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup
[D]Disconnect All
[V]View All Setting
[S]Save & Quit
[Q]Quit Unchanged
setup>v
Model Name
: XX-XXXX
Projector Name
: XX-XXXX
MAC Address
: XX:XX:XX:XX:XX:XX
DHCP Client
: Disable
IP Address
: 192.168.150.3
Subnet Mask
: 255.255.255.0
Default Gateway
: Not Used
RS-232C Baud Rate : 9600 bps
Password
: Not Required
**********(Advanced Status)**********
Data Port
: 10002
Accept IP Address : Accept All
Auto Logout Time : 5 minutes
Search Port
: 5006
1
*1
2
*2
3
*3
1 Enter “1” (number of item to be set), and
press the “Enter” key.
Display current IP address (*1).
2 Enter IP address to be set and press the
“Enter” key.
Display IP address after change (*2).
3 Enter “v” and press the “Enter” key to verify
setting detail list.
IP address is being changed (*3).
Note
• Verification of setting detail list can be omitted.
• Setting details are not effective until they have
been saved. (Page 24)
• If an invalid number is entered, an error
message (“Parameter Error!”) will be displayed.
-23
Setting up the Projector Using RS-232C or Telnet
Save Settings and Quit
([S]Save & Quit)
Quit without Saving Settings ([Q]Quit Unchanged)
Save set values and quit menu.
Quit menu without saving setting values.
▼SETUP MENU
▼SETUP MENU
----------------------------SETUP MENU--------------------------[1]IP Address
[2]Subnet Mask
[3]Default Gateway
[4]User Name
[5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup
[D]Disconnect All
[V]View All Setting
[S]Save & Quit
[Q]Quit Unchanged
----------------------------SETUP MENU--------------------------[1]IP Address
[2]Subnet Mask [3]Default Gateway
[4]User Name
[5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup
[D]Disconnect All
[V]View All Setting
[S]Save & Quit
[Q]Quit Unchanged
setup>s
All Connection will be disconnect.
Continue(y/n)? y
Apply New setting...Done.
1 Enter “s” and press the “Enter” key.
2 Enter “y” and press the “Enter” key.
-24
1
2
setup>q
Quit Without Saving(y/n)? y
Setting Unchanged.
1 Enter “q” and press the “Enter” key.
2 Enter “y” and press the “Enter” key.
1
2
Setting up the Projector Using RS-232C or Telnet
The setting procedure for each item will be explained. For the basic procedure, please
refer to “Set Items” on page 23.
IP Address Setting
Default Gateway Setting
([1]IP Address)
([3]Default Gateway)
Setting of IP address.
Setting default gateway.
setup>1
IP Address
Please Enter
—>
(change)
:192.168.150.2
:192.168.150.3
192.168.150.3
1
2
*
1 Enter “1” and press the “Enter” key.
2 Enter numerical value to be set and press
the “Enter” key.
Display IP address after change (*).
2
*
Note
([2]Subnet Mask)
Setting subnet mask.
:255.255.255.0
:255.0.0.0
255.0.0.0
1
1 Enter “3” and press the “Enter” key.
2 Enter numerical value to be set and press
the “Enter” key.
Display gateway address after change (*).
Subnet Mask Setting
setup>2
Subnet Mask
Please Enter
(change)
—>
setup>3
note: “0.0.0.0” means “Using no default gateway.”
Gateway Address :0.0.0.0
Please Enter
:192.168.150.1
(change)
—> 192.168.150.1
1
• If the values for IP Address, Subnet Mask or
Gateway of the projector have been changed
via Telnet, the computer cannot be connected
to the projector depending on the computer's
network settings.
2
1 Enter “2” and press the “Enter” key.
2 Enter numerical value to be set and press
the “Enter” key.
Display subnet mask after change (*).
*
User Name Setting
([4]User Name)
Carrying out security protection using user
name.
setup>4
User Name
:
Please Enter
: XX-XXXX
(change)
—>
XX-XXXX
1
2
*
1 Enter “4” and press the “Enter” key.
2 Enter user name and press the “Enter” key.
Display set user name (*).
Note
• User name can be up to 8 characters.
• You can input the characters below:
a-z, A-Z, 0-9, -, _
• In the default state, user name is not set.
-25
Setting up the Projector Using RS-232C or Telnet
Password Setting
Projector Name Setting
([5]Password)
([7]Projector Name)
Carrying out security protection using
password.
It is possible to assign a projector name.
setup>5
Password
:
Please Enter
: sharppj
(change)
—> sharppj
1
2
*
1 Enter “5” and press the “Enter” key.
2 Enter password and press the “Enter” key.
Display set password (*).
setup>7
Projector Name
Please Enter
(change)
—>
1
: XX-XXXX
: MY XX-XXXX
MY XX-XXXX
2
*
1 Enter “7” and press the “Enter” key.
2 Enter projector name.
Display set projector name (*).
Note
Note
• Projector name can be up to 12 characters.
• You can input the characters below:
A-Z, 0-9, -, _, (,), space
(When “a-z” are input, they are converted to
“A-Z” automatically.)
• It is the same as the name which can be
confirmed or set, using RS-232C commands
“PJN0”, “PJN1”, “PJN2” and “PJN3”.
• Password can be up to 8 characters.
• You can input the characters below:
a-z, A-Z, 0-9, -, _
• In the default state, the password is not set.
RS-232C Baud Rate Setting
([6]RS-232C Baud Rate)
DHCP Client Setting
Setting of baud rate for RS-232C terminals.
1
setup>6
0 ... 9600 bps
1 ... 38400 bps
2 ... 115200 bps
Baud Rate Select[0-2] :2
RS-232C Baud Rate : 115200 bps
1 Enter “6” and press the “Enter” key.
2 Select and enter the number 0, 1 or 2 and
press the “Enter” key.
Display set baud rate (*).
Note
• Set the projector's baud rate to the same rate
as that used by the computer.
([8]DHCP Client)
Setting DHCP Client to “Enable” or “Disable”.
2
*
Example: When setting DHCP Client to
“Enable”
setup>8
note: It sets DHCP Client.
0 ... Disable
1 ... Enable
DHCP Select[0-1] : 1
DHCP Client : Enable
Success get data from DHCP server.
[MAC Address
] : [XX:XX:XX:XX:XX:XX]
[IP Address
] : [192.168.150.2]
[Subnet Mask
] : [255.255.255.0]
[Default Gateway ] : [0.0.0.0]
[DHCP IP Address] : [192.168.150.1]
1 Enter “8” and press the “Enter” key.
2 Enter “1” and press the “Enter” key.
Display the obtained values (*).
-26
1
2
*
Setting up the Projector Using RS-232C or Telnet
Disconnecting All Connections ([D]Disconnect All)
Setting Auto Logout Time
It is possible to disconnect all the TCP/IP
connections currently recognized by the
projector. Even if the COM Redirect port is
fixed in the Busy status due to a problem, it is
possible to force the Ready status back by
carrying out this disconnection.
If there is no input after a fixed time, the
projector automatically disconnects network
connection using the Auto Logout function. It
is possible to set the time until the projector
is automatically disconnected in units of a
minute (from 1 to 65535 minutes).
setup>d
Disconnect All Connections(y/n)?y
Now Disconnecting...
(ADVANCED[1]Auto Logout Time)
1
2
1 Enter “d” and press the “Enter” key.
2 Enter “y” and press the “Enter” key.
advanced>1
Valid range
: 0 to 65535 (minute)
note: if you enter “0”, auto logout function will be disable.
Auto Logout Time : 5
Please Enter
:15
(change)
—> 15
1
2
*
1 Enter “1” and press the “Enter” key.
2 Enter numerical value and press the
“Enter” key.
Display set numerical value (*).
Note
• If Disconnect All is performed, the connection
to the projector via network will be forcibly
disconnected.
Note
• If the set value is made 0, the Auto Logout
function is disabled.
• If an invalid number is entered, an error
message (“Parameter Error!”) will be displayed
and the screen returns to the ADVANCED
SETUP MENU.
Entering ADVANCED
SETUP MENU
([A]Advanced Setup)
Enters ADVANCED SETUP MENU.
setup>a
********************** ADVANCED SETUP MENU *************************
[1]Auto Logout Time [2]Data Port
[5]Network Ping Test
[6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3)
[9]Accept All IP Addr [0]Search Port
[!]Restore Default Setting
[Q]Return to Main Menu
advanced>
1 Enter “a” and press the “Enter” key.
1
Data Port Setting
(ADVANCED[2]Data Port)
Setting of TCP port number. It is possible to
set in the range of 1025 to 65535.
advanced>2
Valid range
:1025 to 65535
Data Port
:10002
Please Enter
:10005
(change)
—> 10005
1
2
*
1 Enter “2” and press the “Enter” key.
2 Enter numerical value and press the
“Enter” key.
Display set numerical value (*).
Note
• Set according to need. Normally, use with the
factory default setting.
-27
Setting up the Projector Using RS-232C or Telnet
Carrying out Network Ping
Test
Setting of Accept IP Address (ADVANCED[6]Accept IP
(ADVANCED[5]Network Ping Test)
Addr(1) - [8]Accept IP Addr(3))
It is possible to confirm that a network
connection between the projector and a
computer etc. is working normally.
It is possible to improve security of the
projector by allowing connection from only a
prescribed IP address. It is possible to set up
to three IP addresses allowing connection to
the projector.
advanced>5
Ping Test IP addr :192.168.150.1
Please Enter
:192.168.150.152
(change)
—> 192.168.150.152
32 bytes from 192.168.150.152: icmp_seq = 1, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 2, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 3, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 4, time = 0 ms
1
2
*1
*2
1 Enter “5” and press the “Enter” key.
2 Enter IP address of device to be tested and
press the “Enter” key.
Display entered IP address (*1).
Display test result (*2).
Note
• If the “Enter” key is pressed without entering an
IP address, the Ping Test IP address used
previously is entered.
• If there is a fault with the connection, “Error: No
answer” is displayed after a 5 second retry. In
this case, please confirm the settings for the
projector and the computer, and contact your
network administrator.
advanced>6
Accept IP Addr(1) : 0.0.0.0
Please Enter
: 192.168.150.152
(change)
—> 192.168.150.152
1
2
*
1 Enter “6”, “7” or “8” and press the “Enter”
key.
2 Enter numerical value and press the
“Enter” key.
Display set numerical value (*).
Note
• To invalidate the Accept IP Address being
currently set, enter “0.0.0.0”.
• If there is one or more Accept IP Addr being
set, no connections are allowed from IP
addresses that are not yet set. They can be
cancelled using [9]Accept All IP Addr.
Accepting All IP Addresses
(ADVANCED[9]Accept All IP Addr)
Removes IP addresses set with “Accept IP
Addr”.
advanced>9
Accept All IP Addresses(y/n)? y
1 Enter “9” and press the “Enter” key.
2 Enter “y” and press the “Enter” key.
Note
• At the point in time where “y” was entered, the
numerical values for Accept IP Addr(1)-(3) are
reset to “0.0.0.0”.
• If “n” is entered, setting is not altered.
-28
1
2
Setting up the Projector Using RS-232C or Telnet
Setting of Search Port
Return to Main Menu
(ADVANCED[0]Search Port)
(ADVANCED[Q]Return to Main
Menu)
Sets the port number used when searching
for the projector from the network.
advanced>0
Please Enter Port Number for Search from Computer.
Valid range
: 1025 to 65535
Search Port
: 5006
Please Enter
: 5004
(change)
—> 5004
Returns to the main SETUP MENU.
1
2
*
1 Enter “0” and press the “Enter” key.
2 Enter numerical value and press the
“Enter” key.
Display set numerical value (*).
advanced>q
----------------------------SETUP MENU--------------------------[1]IP Address
[2]Subnet Mask
[3]Default Gateway
[4]User Name
[5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup
[D]Disconnect All
[V]View All Setting
[S]Save & Quit
[Q]Quit Unchanged
1
setup>
1 Enter “q” and press the “Enter” key.
Returns to the SETUP MENU.
Note
• Set according to need. Normally, use with the
factory default setting.
Return to Default Settings
(ADVANCED[!]Restore Default
Setting)
Returns all menu setting values to the default
state.
advanced>!
Restore All Setting to Default(y/n)? y
— User Setting Initialized —
1
2
1 Enter “!” and press the “Enter” key.
2 Enter “y” and press the “Enter” key.
Note
• If the values for IP Address, Subnet Mask or
Gateway of the projector have been returned to
the default settings via Telnet, the computer
cannot be connected to the projector
depending on the computer's network settings.
-29
Resetting the Lamp Timer of the Projector via LAN
When the projector is connected to a network, you can use the communications program
to send a command to reset the lamp timer. The example below uses Windows® XP as the
operating system. When you use Windows Vista®, use other communications program
referring to the following steps, because Windows Vista® does not come with
HyperTerminal.
1
Click “Start” – “All Programs” –
“Accessories” – “Communications” – “HyperTerminal”.
• If you do not have HyperTerminal installed,
see the operation manual of your computer.
• Depending on the settings of your computer,
you may be required to enter your area code
and other details. Enter the information as
required.
2
Enter a name in the “Name” field,
and click “OK”.
3
If you are required to enter the
area code, enter it in the “Area
code” field. From the “Connect
using” drop-down menu, select
“TCP/IP (Winsock)”, and click
“OK”.
Select
“TCP/IP (Winsock)”
4
-30
Enter the IP address of the
projector in the “Host address”
field (see “TCP/IP” on the
“Network” menu of the projector),
and enter the data port of the
projector in the “Port number”
field (“10002” is the factory default
setting), and click “OK”.
Resetting the Lamp Timer of the Projector via LAN
5
Click “Properties” on the “File”
menu.
6
Click the “Settings” tab, and then
click “ASCII Setup”.
7
Select the check boxes next to
“Send line ends with line feeds”,
“Echo typed characters locally”,
and “Append line feeds to
incoming line ends”, and click
“OK”.
• The LAMPRESET Properties window
appears, click “OK”.
8
If a user name and/or password is
set for the projector, enter the
user name and password.
9
Send the lamp reset command
“LPRE0001”.
• This command can only be sent when the
projector is in standby mode.
• When “OK” is received, this indicates that the
lamp was successfully reset.
10 Close HyperTerminal.
-31
Troubleshooting
Communication cannot be established with the projector
When connecting the projector using serial-connection
\ Check that the RS-232C terminal of the projector and a computer or the commercially
available controller are connected correctly.
\ Check that the RS-232C cable is a cross-over cable.
\ Check that the RS-232C port setting for the projector corresponds to the setting for the
computer or the commercially available controller.
When connecting the projector to a computer using network (LAN)connection
\ Check that the cable's connector is firmly inserted in the LAN terminal of the projector.
\ Check that the cable is firmly inserted into a LAN port for a computer or a network device
such as a hub.
\ Check that the LAN cable is a Category 5 cable.
\ Check that the LAN cable is a cross-over cable when connecting the projector to a computer
directly.
\ Check that the LAN cable is a straight-through cable when connecting the projector with a
network device such as a hub.
\ Check that the power supply is turned on for the network device such as a hub between the
projector and a computer.
Check the network settings for the computer and the projector
\ Check the following network settings for the projector.
• IP Address
Check that the IP address for the projector is not duplicated on the network.
• Subnet Mask
When the gateway setting for the projector is “0.0.0.0” (Not Used), or the gateway setting
for the projector and the default gateway setting for the computer are the same:
• The subnet masks for the projector and the computer should be the same.
• The IP address parts shown by the subnet mask for the projector and the computer
should be the same.
(Example)
When the IP address is “192.168.150.2” and the subnet mask is “255.255.255.0” for the
projector, the IP address for the computer should be “192.168.150.X” (X=3-254) and the
subnet mask should be “255.255.255.0”.
• Gateway
When the gateway setting for the projector is “0.0.0.0” (Not Used), or the gateway setting
for the projector and the default gateway setting for the computer are the same:
• The subnets for the projector and the computer should be the same.
• The IP address parts shown by the subnet mask for the projector and the computer
should be the same.
(Example)
When the IP address is “192.168.150.2” and the subnet mask is “255.255.255.0” for the
projector, the IP address for the computer should be “192.168.150.X” (X=3-254) and the
subnet mask should be “255.255.255.0”.
Note
• When “DHCP Client” is set to “OFF” on the projector:
IP address: 192.168.150.2
Subnet mask: 255.255.255.0
Gateway address: 0.0.0.0 (Not Used)
• For network settings for the projector, refer to page 13.
-32
Troubleshooting
\ Take the following steps for checking the network settings for the computer.
1. Open a command prompt.
• In the case of Windows® 2000: click “start” ➔ “Programs” ➔ “Accessories”
➔ “Command Prompt” in order.
• In the case of Windows® XP, Windows Vista®: click “start” ➔ “All Programs”
➔ “Accessories” ➔ “Command Prompt” in order.
2. After launching the command prompt, enter the command “ipconfig”, and press the “Enter”
key.
Note
• Communication may not be established even after carrying out the network settings
for the computer. In such cases, restart your computer.
C:\>ipconfig
Note
• Usage examples of ipconfig
C:\>ipconfig /?
displays how to use “ipconfig.exe”.
C:\>ipconfig
displays the set IP address, subnet mask and default gateway.
C:\>ipconfig /all displays all the setting information related to TCP/IP.
3. To return to the Windows® screen, enter “exit” and press the “Enter” key.
-33
Troubleshooting
\ Check if the “TCP/IP” protocol is operating correctly using the “PING” command. Also, check
if an IP address is set.
1. Open a command prompt.
• In the case of Windows® 2000: click “start” ➔ “Programs” ➔ “Accessories” ➔
“Command Prompt” in order.
• In the case of Windows® XP, Windows Vista®: click “start” ➔ “All Programs” ➔
“Accessories” ➔ “Command Prompt” in order.
2. After launching the command prompt enter a command “PING”.
Entry example C:\>ping XXX.XXX.XXX.XXX
“XXX.XXX.XXX.XXX” should be entered with an IP address to be connected to, such as the
projector.
3. When connecting normally, the display will be as follows.
(The screen may be slightly different depending on the OS type.)
<Example> when the IP address connected to is “192.168.150.1”
4. When a command cannot be sent, “Request time out” will be displayed.
Check the network setting again.
If communication can still not be established properly, contact your network administrator.
5. To return to the Windows® screen, enter “exit” and then press the “Enter” key.
\ When the projector cannot be connected, even though the “PING” command is checked:
1. When “Accept IP Address” is set on the projector, set the IP address of the PC to be
connected.
2. When a security software is installed on the PC, or when a fire wall has been set up for the
network system, connection may not be possible. Consult the system administrator when,
for example, you want to change the settings to enable use of the TCP port set as the data
port.
3. When neither of the above two items applies, change the settings for the data port.
A connection cannot be made because you have forgotten your user name
or your password.
\ Initialize the settings. (See page 51 of the projector's operation manual.)
\ After the initialization, carry out setting again.
-34
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising