PD-2 2-Channel Voice Dialer

PD-2 2-Channel Voice Dialer
PD-2
1. PRODUCT DESCRIPTION
2-CHANNEL
PROFESSIONAL
VOICE
DIALER
Installation
Instructions
(760) 438-7000 • FAX (760) 438-7043
USA & Canada (800) 421-1587 & (800) 392-0123
Toll Free FAX (800) 468-1340
www.linearcorp.com
4. PLUG TELEPHONE INTO DIALER (OPTIONAL)
2. DIALER FEATURES & SYSTEM OVERVIEW
The 2-channel Model PD-2 Professional Voice Dialer is designed to connect to security or
personal emergency systems. Two voice messages (each up to 10 seconds long) can be
recorded into the dialer’s digital memory. Each dialer channel can dial up to four telephone
numbers to play its message. The PD-2 can also be used to dial pager numbers and send
numeric messages. Nine to 16 VDC power for the dialer is supplied from the triggering device.
When triggered (by grounding one of the two inputs), the dialer begins its communication
sequence. After a 15 second delay, the dialer will attempt to call the first telephone number
programmed for the channel triggered. The dialer will go “off-hook” and try to detect a dial tone.
After the dial tone is detected, the unit will start dialing. If no dial tone is detected for five seconds,
the dialer goes “on-hook”, waits for three seconds; goes “off-hook”, then tries to detect a dial
tone again. If no dial tone is detected on the second try, the call to the first telephone number
is aborted and the dialer will attempt to call the next telephone number.
In the case of a false alarm, the 15 second start-up delay gives the user time to cancel the
message before it’s sent by pressing the dialer’s STOP button. The start-up delay can be set
for 0, 15, 30, 60 or 120 seconds. The 120 second delay option allows the dialer to be used for
redundant voice reporting on the same system and telephone line with a faster triggering digital
communicator.
Five seconds after dialing, the unit begins playing the voice message for the channel triggered.
The message repeats for 60 seconds. During the message, the dialed party can stop the
communication sequence and prevent the dialer from calling the next telephone number by
pressing any key on their telephone keypad. If a pager number is programmed, no voice
message is played for that telephone number.
With the listen-in option enabled, the dialed party can listen to the protected premises using
the dialer’s built-in microphone. When the dialed party presses any telephone key during the
message, the message will stop and the microphone will be switched on for 60 seconds.
Pressing any key extends the time another 60 seconds, pressing 99 hangs up.
Other programmable options allow tone or pulse dialing, and disabling the dialed party
communication stop feature.
5. CONNECT & WIRE DIALER INPUT
ON THE FACEPLATE CARD
SUPPLIED, FILL IN THE NAMES
AND TELEPHONE NUMBERS OF
THE PEOPLE THAT THE DIALER
WILL CALL
DIALER PLUGS
INTO A TELEPHONE
WALL JACK
TELEPHONE
CORD PLUGS
INTO VOICE
DIALER'S PHONE
JACK
TELEPHONE
WITH A TELEPHONE
CONNECTED YOU CAN
LISTEN TO THE DIALER AS IT
MAKES ITS CALLS AND
PLAYS ITS MESSAGE
DURING SYSTEM TESTING
PLUG THE DIALER INPUT
WIRE INTO THE DIALER'S
CONSOLE JACK
WIRES CAN BE
ROUTED INSIDE THE
WIRING TROUGHS
IF REQUIRED
MICROPHONE
DIALER INPUT WIRE
FOR POWER AND TRIGGER
CONNECTS TO THE
DIALER'S CONSOLE JACK
PLACE THE CARD ON THE
DIALER, THEN SECURE IT
WITH THE CLEAR PLASTIC
RETAINER
THE DIALER CAN BE
WALL MOUNTED OR USED
ON A TABLE TOP (APPLY
FOUR PLASTIC "FEET"
FOR TABLE TOP USE)
PD-2
DIALER
DIALER
"IN-USE"
INDICATOR
ALARM
CONTROL
PANEL
6. PROGRAM VOICE MESSAGES
RED
CONNECT THE
TELEPHONE
TO THE DIALER'S
PHONE JACK
YELLOW
CHANNEL #1 TRIGGER
SHORT-TO-COMMON TO ACTIVATE
GREEN
CHANNEL #2 TRIGGER
SHORT-TO-COMMON TO ACTIVATE
BLACK
COMMON POWER NEGATIVE
DIALER INPUT WIRE
8. PLUG PHONE LINE INTO DIALER
PLUG ONE END OF THE
TELEPHONE LINE INTO
THE TELEPHONE
WALL JACK
POWER INPUT + 9 TO +16 VDC
20 mA IDLE, 100 mA OPERATING
9. TEST DIALER
RED LIGHT TURNS ON
PRESS
RED LIGHT BLINKS ONCE
RED LIGHT ON DURING
MESSAGE RECORDING
(MESSAGE CAN BE UP
TO 10 SECONDS LONG)
AT END OF
MESSAGE
PRESS
RED LIGHT TURNS OFF
10. PROGRAMMABLE OPTIONS
1
TRIGGER THE DIALER
2
AFTER 15 SECONDS, THE DIALER'S RED LIGHT WILL
TURN ON AND THE CALL SEQUENCE FOR THE
TRIGGERED CHANNEL WILL BEGIN
3
PICK UP THE TELEPHONE HANDSET TO MONITOR THE
PROGRESS OF THE CALL(S)
4
PRESS ANY KEY ON THE TELEPHONE (OR PRESS AND
HOLD THE DIALER'S STOP KEY) TO DISCONNECT THE
DIALER AND STOP ITS CALL SEQUENCE
DIALING TYPE
AUDIO LISTEN-IN
TONE DIALING (DEFAULT)
DISABLE AUDIO LISTEN-IN (DEFAULT)
PULSE DIALING
ENABLE AUDIO LISTEN-IN
DIALING DELAY
CALL ACKNOWLEDGE
0
SECONDS
TO
TRIGGERING
DEVICE
15
SECONDS
(DEFAULT)
30
SECONDS
PRESS ANY KEY
TO STOP THE DIALER
SELECT CHANNEL #1 OR #2
RECORD
JOE'S ALARM
YOUR
IS SOUNDING
ALARM
MESSAGE
DIALING TONES
AND RECORDED
MESSAGE
PLUG THE OTHER END
OF THE TELEPHONE
LINE INTO THE DIALER'S
LINE JACK
OR
RED DIALER
"IN-USE" INDICATOR
HANG UP OR LISTEN-IN WHEN ANY
TELEPHONE KEY IS PRESSED (DEFAULT)
60
SECONDS
120
SECONDS
7. PROGRAM PHONE OR PAGER NUMBERS
START HERE
PRESS
PRESS
UP TO FOUR TELEPHONE
NUMBERS CAN BE PROGRAMMED
FOR EACH DIALER CHANNEL
TELEPHONE LINE
PLUGS INTO
DIALER'S
LINE JACK
START HERE
CONNECTING A TELEPHONE
TO THE DIALER IS OPTIONAL
3. FILL IN FACEPLATE CARD
PRESS THE PROGRAM BUTTON, THE RED LIGHT
WILL TURN ON (THE RED LIGHT WILL BLINK ONCE
AS EACH KEY IS PRESSED)
PRESS 1~4 FOR CHANNEL #1, 5~8 FOR CHANNEL #2,
TO SELECT THE TELEPHONE NUMBER TO PROGRAM
ENTER EACH TELEPHONE DIGIT, PRESSING THE DIAL
BUTTON BEFORE EACH DIGIT. UP TO 30 DIGITS MAXIMUM.
DIALING DELAYS: PRESSING DIAL TWICE ADDS A 2-SECOND
DIALING DELAY, EACH TIME DIAL IS PRESSED IN SUCCESSION
2 MORE SECONDS ARE ADDED TO THE DELAY. EACH DIALING
DELAY USES UP A DIGIT.
FOR PAGERS: ENTER THE PAGER TELEPHONE NUMBER
FIRST. USE DIALING DELAYS TO ALLOW TIME FOR THE
PAGING SYSTEM TO ANSWER BEFORE THE NUMERIC
MESSAGE IS SENT BY THE DIALER. PRESS DIAL TWICE
AS THE LAST DIGIT OF THE NUMERIC MESSAGE TO
PREVENT PLAYING THE VOICE MESSAGE.
PRESS THE STOP BUTTON WHEN FINISHED
RED LIGHT GOES OFF
TO ERASE A NUMBER: PRESS PROG, 1~8, DIAL, STOP
WARNING: IT IS ILLEGAL TO PROGRAM THIS DIALER
TO DIAL POLICE OR FIRE EMERGENCY NUMBERS DIRECTLY
LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12) months.
The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale
customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not
warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature
of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear corporation
for consequential damages arising out of or in connection with use or performance of this product
or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal,
installation, or reinstallation. All implied warranties, including implied warranties for merchantability and
implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This
Linear Corporation Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#).
Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
FCC NOTICE
This equipment generates and uses radio frequency energy and if not installed and used properly,
that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio and
television reception. It has been type tested and found to comply with the limits for a Class B computing
device in accordance with Part 15 of FCC Rules, which are designed to provide reasonable protection
against such interference in a residential installation. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
✶ Relocate the dialer away from the TV/radio receiver.
✶ Plug the dialer into a different wall outlet so that the dialer is on a different branch circuit.
✶ Re-orient the TV/radio antenna.
✶ If necessary, the user should consult the dealer or an experienced radio/television technician for
additional suggestions.
✶ Changes or modifications to the device may void FCC compliance.
CALL ALL NUMBERS REGARDLESS
IF ANY TELEPHONE KEY IS PRESSED
Copyright © 2000 Linear Corporation
214619 A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising