Toll Free: 1-888-865-6888 Tel: 510-226-8368 Fax: 510-226-8968 Email:

Toll Free: 1-888-865-6888 Tel: 510-226-8368 Fax: 510-226-8968 Email:
Toll Free: 1-888-865-6888
Tel: 510-226-8368 Fax: 510-226-8968
Email: sales@RackmountMart.com
User Manual
17” High Resolution 1920 x 1200 LCD
LCDR6U17-01
6U Rackmount Display Panel
Options :
- SDI / MC
- DC power
- Touchscreen
- MIL-type or lockable connector
Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness
of the contents. The information in this document is subject to change without notice. We are not liable for any injury or
loss that results from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for
future reference.
■
■
■
■
■
■
■
■
■
■
■
Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearby.
When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
Observe all precautions and warnings attached to the equipment.
If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being
damaged by transient over-voltage.
Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and
invalidate its warranty.
If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
■
■
■
Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or
failure to follow instructions supplied with the product.
Repair or attempted repair by anyone not authorized by us.
Any damage of the product due to shipment.
Removal or installation of the product.
Causes external to the product, such as electric power fluctuation or failure.
Use of supplies or parts not meeting our specifications.
Normal wear and tear.
Any other causes which does not relate to a product defect.
Removal, installation, and set-up service charges.
□
□
□
□
□
□
□
□
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
■ Re-position or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
www.rackmountmart.com
Contents
< Part. 1 > LCDR6U17-01
1.1
1.2
1.3
Package Content
Structure Diagram & Dimension
Installation
P.1
P.1 - 2
P.3
< Part. 2 > Specifications / OSD / Remote Controller
2.1
2.2
2.3
Product Specifications
On-screen Display Operation ( OSD )
Picture In Picture ( PIP ) / Picture By Picture ( PBP )
P.4 - 5
P.6 - 7
P.8 - 9
< Part. 3 > Options
3.1
3.2
3.3
3.5
3.6
3G / HD / SD-SDI Broadcast-grade input
MC Multi-display control solution
17” Touchscreen : Resistive, Capacitive
48V, 24V or 12VDC power
MIL-type or lockable connector
( except RP-717 )
P.10
P.11
P.12
P.13
P.14
www.rackmountmart.com
Before Installation
■ It is very important to mount the equipment in a suitable cabinet or on a stable surface.
■ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
How To Clean Your LCD Monitor
Caution :
■
To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
■
When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.
■
Use only cleansers made specifically for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the finish.
■
Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
■
Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
1
Disconnect the power cord.
2
Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
1
Disconnect the power cord.
2
Spray a small amount of non-abrasive cleanser on a microfiber cloth.
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your
microfiber cloth first, not directly on the parts you are cleaning.
3
Gently wipe the surface. Use as little pressure as possible.
4
Wait until your monitor is completely dry before plugging it in and powering it up.
www.rackmountmart.com
< Part 1 >
< 1.1 > Package Content
LCDR6U17-01 X 1
- 6ft VGA cable X 1
- Power adapter X 1
- Power cord X 1
< 1.2 > Structure Diagram
Front view
2
1
3
Power adapter
Rear view
3
1
LCD panel
2
LCD membrane
3
Audio speaker
4
Power adapter basket
DVI-D
Audio
Power cord
Power BNC S-Video
VGA
HDMI
out - in - in
Video PC
Standard : VGA + DVI-D + HDMI + BNC + S-Video + audio
Option
: SDI, USB for touchscreen & DC power
P.1
www.rackmountmart.com
< 1.2 > Dimension
Front View
Side View
UNIT : mm
Bottom View
1mm = 0.03937 inch
Model
Product Dimension
(W x D x H)
Net
Weight
LCDR6U17-01
480 x 48 x 266 mm
18.9 x 1.9 x 10.5 inch
4.5 kg
9.9 lbs
P.2
www.rackmountmart.com
< 1.3 > Installation
Step
■
■
1
Mount the display panel with M6 screw set.
M6 screw x 4 pcs required ( Left & right side ).
M6 screw sets are not provided.
Step
■
P.3
2
Fix the LCD into the rack.
www.rackmountmart.com
< Part 2 >
< 2.1 > Product Specifications
LCD
Panel
Panel Size ( diagonal )
17.1-inch Widescreen TFT color LCD
Display pixel ( dots x lines )
1920 x 1200
Brightness ( typ. )
210
Contrast Ratio ( typ. )
600:1
Color
16.7 M, 8-bit
Viewing Angle ( L/R/U/D )
65/65/55/55
Response Time ( ms )
30
Dot pitch ( mm )
0.191
Display Area ( mm )
367.20H x 229.50V
Surface treatment
Anti-glare, Hard-coating
Surface hardness
3H
Backlight Type
LED
MTBF ( hrs )
Video
Connectivity
Digital
HDMI
HDMI 1.1, CEA-861-D
DVI
DVI-D, TMDS single link
VGA
Analog 0.7Vp-p
Composite ( BNC )
NTSC & PAL
S-Video ( 4-pin )
NTSC & PAL
Plug & Play
DVI / VGA
VESA EDID structure 1.3
Synchronization
VGA
Separate, Composite & SOG
Audio Input
Connector
3.5mm stereo jack
Impedance / Power level
30kΩ / 750mV
Connector
3.5mm stereo jack
Resistance / Power level
30kΩ / 2.8V
Power
2 x 2W
Analog
Audio
Connectivity
20,000
Audio Output
Speaker Output
*When the audio output is connected, speaker output is OFF
Power
Regulatory
Power Supply
Range
Auto-sensing 100 to 240VAC,
50 / 60Hz
Power Consumption
Screen display ON
34W or less
Power saving mode
4W or less
Power button OFF
1W or less
Safety Approval
FCC & CE
P.4
www.rackmountmart.com
Environmental
Conditions
Operating
Storage
Physical
Specification
Temperature
0 to 50°C degree
Humidity
20~90%, non-condensing
Temperature
-5 to 60°C degree
Humidity
5~90%, non-condensing
Shock
10G acceleration (11ms duration)
Vibration
5~500Hz 1G RMS random
Product ( W x D x H )
480 x 48 x 266 mm
18.9 x 1.9 x 10.5 inch
Net Weight
Applicable
Format
DVI-D / VGA Input
4.5 kgs / 9.9 lbs
PC Signal
1920 x 1200 x 60Hz
1920 x 1080 x 60Hz
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 768 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
HDMI Input
PC Signal
Same as VGA
Video Signal
1080p : 60Hz
Audio Signal
P.5
720p
: 50 / 60Hz
480p
: 60Hz
576p
: 50Hz
2ch Linear PCM ( 32 / 44.1 / 48 KHz )
www.rackmountmart.com
< 2.2 > On-screen Display Operation ( OSD )
Membrane Switch
Function
Turn the monitor on or off
Display the OSD menu
Act as an Enter key to select screen setting options
Scroll through menu options and adjust
the displayed control
Exit the OSD screen
Go back to the previous on-screen sub-menu or
main menu
Remark : All LED touch buttons in WHITE light.
The LED of Power
touch button will flash continuously when there is
no signal input.
1
1
All the LED touch buttons will automatically turn off after 10 minutes of idle status
( except the Power
).
2
Light up all membrane buttons, please press any button for 1 - 2 seconds ( except
the Power
).
Picture
Picture mode :
Standard / Vivid / Soft / User mode to choose
Brightness :
Adjust background black level of the screen image
Contrast :
Adjust the difference between the image background
(black level) and the foreground (white level)
Hue:
Adjust the screen hue value
Saturation :
Adjust the saturation of the image color
Picture size :
Adjust the image size
Color temp :
Standard / Cool / Warm / User to choose
Noise reduce :
Reduce the noise of the image
Sharpness :
Adjust the image from weak to sharp
P.6
www.rackmountmart.com
< 2.2 > On-screen Display Operation ( OSD )
2
3
PC
Auto adjust :
Automatically adjust sizes, centers and fine tunes the
video signal to eliminate waviness and distortion.
Clock :
Adjust the clock value
Phase :
Adjust the phase value
H. Position :
Align the screen image left or right
V. Position :
Align the screen image up or down
Audio
Audio mode :
Movie / Voice / Normal / Music mode to choose
Volume :
Adjust the volume of sound
Bass :
Set the value of bass sound
Treble :
Set the value of treble sound
Balance :
Set the balance value of treble and bass sound
Analog TV audio : Set the value of analog TV audio sound
Mute :
4
Turn off the surrounding sound
MISC
Language :
Select the language in which the OSD menu is
displayed - English
Sleep timer :
Set the off time
PIP mode :
Adjust picture in picture setting
PIP position :
Enter into PIP position
PIP source :
Enter into the Sub source and sound source
System reset :
Return the adjustment back to factory setting
Information :
Select for Help
P.7
www.rackmountmart.com
< 2.3 > How to Use Picture In Picture ( PIP ) / Picture By Picture ( PBP )
< 2.3.1 > Picture in Picture ( PIP )
Mode
Display the Sub screen in the Main screen.
OSD Menu → MISC → PIP Mode → Large / Small / OFF
Main screen
Sub screen
Position
Adjust the position of the Sub screen ( top left, bottom left, top right, bottom right )
OSD Menu → MISC → PIP Position → top left / top right / bottom left / bottom right
top left
top right
bottom left
bottom right
Size
Adjust the size of the Sub screen ( Large / Small )
OSD Menu → MISC → PIP Mode → Large / Small
Size of Sub screen
LCD Monitor
Large Sub screen
Small Sub screen
1920 x 1200
552 x 414
480 x 360
1920 x 1080
552 x 414
480 x 360
1440 x 900
414 x 310
360 x 270
1366 x 768
392 x 294
340 x 254
1280 x 1024
368 x 276
320 x 240
P.8
www.rackmountmart.com
< 2.3.2 > Picture By Picture ( PBP )
Mode
Display the Sub screen next to the Main screen.
OSD Menu → MISC → PIP Mode → PBP
Main screen
Sub screen
Size
LCD Monitor
Main / Sub screen
1920 x 1200
955 x 716
1920 x 1080
955 x 716
1440 x 900
715 x 536
1366 x 768
678 x 508
1280 x 1024
635 x 476
< 2.3.3 > PIP / PBP Source
To select an input signal for PIP / PBP Sub screen.
OSD Menu → MISC → PIP Source → VGA / S-Video / Composite / DVI / HDMI / SDI / YPbPr / TV
The PIP / PBP is operable in the following table :
Sub
VGA
S-Video
Composite
DVI-D
HDMI
SDI
YPbPr
TV
VGA
x
o
o
o
o
o
o
o
S-Video
o
x
x
o
o
o
o
x
Composite
o
x
x
o
o
o
o
x
DVI
o
o
o
x
x
o
o
o
HDMI
o
o
o
x
x
o
o
o
SDI
o
o
o
o
o
x
x
o
YPbPr
o
o
o
o
o
x
x
o
TV
o
x
x
o
o
o
o
x
Main
P.9
www.rackmountmart.com
< Part 3 >
< 3.1 > Options : 3G / HD / SD-SDI input
Our SDI input is an ideal solution for the broadcast-grade video
and high resolution CCTV market.
Designed for use with Full HD 1080p and ultra high resolution
1920 x 1200 LCD displays, we provide a SDI input module without
using additional space or power.
SDI
Audio
DVI-D
Power BNC S-Video
VGA
out - in - in
Video PC
INPUT
Standard Compliance
Compatible Video Format
Compatible Audio Format
Max. Transmission Distance
75 ohm coaxial cable
HDMI
out
-
in
3G-SDI IN
BNC x 1 / 0.8Vp-p ( 75 ohm )
3G-SDI OUT
BNC x 1 / Active through, equalized & relocked
Video
SMPTE 425M / 274M / 296M / 125M
ITU-R BT.656
Audio
SMPTE 299M / 272M-C
3G-SDI
1080p
1080p
1080i
720p
@60 / 50Hz, 4:2:2
@30 / 25 / 24Hz, 4:4:4
@60 / 50Hz, 4:4:4
@60 / 50Hz, 4:4:4
HD-SDI
1080p
1080i
720p
@30 / 25 / 24Hz, 4:2:2
@60 / 50Hz, 4:2:2
@60 / 50Hz, 4:2:2
SD-SDI
480i
@60Hz, 4:2:2
ITU-R BT.656
576i
@50Hz, 4:2:2
3G-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
HD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
SD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized /
Asynchronized Video
3G-SDI
150m at 2.97Gb/s
HD-SDI
250m at 1.485Gb/s
SD-SDI
480m at 270Mb/s
P.10
www.rackmountmart.com
< 3.2 > Options : MC
( Multi-display Control )
More control is always good. Especially when it is necessary and
easy. Synergy Global Technology provides MC solution to control
the OSD of various Industrial LCD displays up to 64 units.
The RS-232C is used for the communication between the PC and
the first display via a 15 feet serial cable while the CAN bus is
used for the various LCD displays cascade together via CAT 5/6
cable, and daisy chain up to 1,000 meters.
Designed for use with our Industrial LCD displays, we provide
a MC input module without using additional space or power.
Audio
HDMI
Power BNC S-Video
out - in - in
Video PC
VGA
MC
DVI-D
set out
in
Link
*** Please download the protocol of MC control at :
http://www.rackmountmart.com/dataSheet/SGTI-Multi-Display_Spec_20703.pdf
*** For MC
option, the AD board will be upgraded and comes standard with HDMI, DVI-D, VGA, S-Video,
BNC and audio inputs. Casing depth will be changed.
Set switch
For the 1st and last display,
push the set switch upward
RS-232C
For other daisy chain displays,
push the set switch downward
15 feet serial cable
( over 15 feet, extender required )
LINK
OUT
IN
Cat5 / 6 cable
max. 300 meters
OUT
IN
Cat5 / 6 cable
max. 300 meters
OUT
IN
OUT
Cat5 / 6 cable
max. 300 meters
RJ-45 jack
Daisy chain up to 1,000
meters and 64 displays
P.11
up to 64 displays
www.rackmountmart.com
< 3.2 > Options : Touchscreen & driver
17" USB Touchscreen Specification
Model
TRB
Resistive
TCB
Capacitive
Technology
5-Wire Resistive
Capacitive
Touch Point
Single
Single
Stylus or Finger
Finger
≤ 50g / Stylus=R0.8
≤ 50g
10 million touches
300 million touches
15 ms
20 ms
80% ± 3%
92% ±2%
3H
9H
Haze
8% ± 3%
7%
Glass
2.2 ±0.2 mm
2.8 mm ±10%
Method
Activation Force
Durability
Response Time
Optical Transmittance
Surface Hardness
Connector
USB Type A
Compatibility
■
■
■
Windows 7 / XP / Vista, Linux
USB touchscreen package includes 1 x 6ft USB cable, quick reference guideline and CD disc
For detailed information, please refer to the attached CD disc
As the touchscreen unit is not made of toughened glass, please handle it carefully
USB Touchscreen
DVI-D
Audio
Power BNC S-Video
VGA
HDMI
out - in - in
Video PC
TRB & TCB Driver
Please follow the below steps to setup the touch screen:Step 1. Run the bundled CD disc or download the driver from the link below :
http://www.rackmountmart.com/downloads.html
Step 2. Double click the Setup.exe
Step 3. Follow the installation instruction to finish the setup
Step 4. After installation, run the TouchKit program & the “4 point calibration”
Please do the initial calibration
after the first setup
P.12
www.rackmountmart.com
< 3.3 > Options : DC Power
Model
12V
24V
48V
Input voltage:
12-Volt
24-Volt
48-Volt
Input range:
9 ~ 18V
18 ~ 36V
36 ~ 75V
- No load
50 mA
50 mA
50 mA
- Full load
4950 mA
2450 mA
1220 mA
Output voltage:
12-Volt
12-Volt
12-Volt
Output current:
4.16A
4.16A
4.16A
Efficiency
84%
85%
85%
Input rating
Input current
Output rating
P.13
www.rackmountmart.com
< 3.4 > Options : MIL-type or Lockable Connector
Input
MIL - type
Connector
Part no.
MIL Standard
DC Power ***
( Male )
MS3470W8-33P
MIL - DTL - 26482
VGA ***
( Male )
MS3470W14-15P
MIL - DTL - 26482
*** There are several additional MIL DC and VGA connector types with varying design
characteristics to meet cost considerations and to provide users with the most
design flexibility possible. For more information, please contact us.
Input
Lockable
Connector
Part no.
DC Power
( Male )
YM-Ext-461CP001
USB
LUSB - A111 - 00
Standard
D-type 3W3
-
*** MIL - type or Lockable connectors above can be integrated with our LCD displays.
Sale service just for connectors not provided.
The company reserves the right to modify product specifications without prior notice and assumes no responsibility
for any error which may appear in this publication.
All brand names, logo and registered trademarks are properties of their respective owners.
Copyright 2012 Synergy Global Technology Inc. All rights reserved.
P.14
www.rackmountmart.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising