Feature Sheet ODP-4ST 04-06-10

Feature Sheet ODP-4ST 04-06-10
ODP-4ST Optical Node
A Compact Optical Satellite L-Band Distribution System
Features
• • • • • A high-capacity, fiber optic receive node for distributing up to four satellite feeds through a single-mode fiber passive optical network (PON)
Provides flexible commercial installations distributed over fiber optic cable rather than coaxial cable.
Supports a variety of node network sizes.
Simplifies installation and overall equipment needs using standard commercial dish antennas and residential hardware.
Distributes up to four satellite feeds providing access to more channels available than in typical commercial installations, including complete lineups of high-definition programming and Video-On-Demand content.
Instructions
• Use the ODP-4ST with a Dish Optical Network 4 Sat Headend (part number 161299) or the Fiber Stacker, 4 Sat (part number 161563).
• Use the outputs of the ODP-4ST with a Dish Pro or a Dish Pro Plus series switch or to extend L-Band DP trunks.
Installation Considerations
• • •
•
•
Carefully review safety and installation instructions prior to using this product.
The optical network headend (part number 161299) uses a Class 3b laser. The fiber stacker (part number 161253) uses a Class 1 laser.
Standard PON splitters may be used between the optical headend device and the ODP-4ST devices.
Different optical system loss budgets need to be taken into account when using the two
optical headend options.
If full PONs are not used, equivalent optical loss must be added to prevent damage to the ODP-4ST and/or
ODPP-43.
OPTICAL DISHPRO
MODEL ODP-4ST
175487
(via fiber network)
To Distribution System
(Trunk Outputs)
POWER ANY PORT
MADE IN
CHINA
TRUNKED
OUTPUT
LNB 1
[1530u]
TRUNKED
OUTPUT
LNB 2
[1530c]
TRUNKED
OUTPUT
LNB 3
[1550c]
TRUNKED
OUTPUT
LNB 4
[1550u]
TO FIBER
NETWORK
1
2
3
4
5
Page 1 of 2
ODP-4ST Optical Node
A Compact Optical Satellite L-Band Distribution System
Headend Processor
System
HARDWARE
Optical Splitters
Optical Input Devices*
Fiber Optic Cable
OPTICAL MULTIPLEXER
Up to 64 node network (PN 161563)
Up to 512 node network (PN 161299)
ODP-4ST or ODPP43
Single-Mode Fiber
Band Translating Switch
Used with dual-tuner/single cable installs
Separator (BTSS)
Approximate
Dimensions
8.75” x 5.75” x 1.35”
(in inches H x W x D)
Input Signal
SUBSCRIBER UNIT
Optical Multiplexer
Input Connectors
Output
Output Connectors
Output Optical Power
System Power
Status and Monitoring
Input
Input Connector
Input Optical Power
Output
System Power
System Optical
Budget
Up to four 950-2150 MHz dual-polarity orbital locations
Four female F-connectors
One dual wavelength (1530/1550 nm) single-mode fiber output
One FC/UPC female single-mode fiber connector
+5 dBm total (+2 dBm each wavelength) (PN 161563)
+23 dBm total (+20 dBm each wavelength) (PN 161299)
120V AC
Part Number 161299
• LED indicators (system DC power and optical alarms)
• Optical power output monitor port
Part Number 161563
• None
One dual wavelength (1530/1550 nm) single-mode fiber
One FC/UPC female single-mode fiber connector
-13 dBm +/- 3dB
Four female F-connector ports, DP stacked 950-2150 MHz
The line is powered by a DP or DPP switch. An AC power adapter is
required for trunked application without DP or DPP switches.
12 dB nominal (PN 161563)
30 dB nominal (PN 161299)
* The 64 node or 512 node networks can consist of both ODP-4ST and ODPP-
43 devices in any combination up to the node size limit.
© 2010 EchoStar Technologies L.L.C.
Rev. 04/06/10 Contents subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising