Assembly GUIDE Waterfall Wine Cellar Kit 888.373.6057 Required

Assembly GUIDE Waterfall Wine Cellar Kit 888.373.6057 Required
Waterfall Wine Cellar Kit
Assembly GUIDE
Questions?
888.373.6057
or visit
Page 1
wineracksamerica.com
tools for assembly
Required
Wood Glue
Screwdriver
Suggested
Cordless Drill
Finish Nailer
+
Hammer
Nail Setter
SINGLE DEEP PACKAGE CONTENTS
MIDDLE LADDER ASSEMBLIES (*VARIOUS LENGTHS) x 9
77 1/8"
HORIZONTAL TRIM PIECE x 3
9 9/16"
SMALL BAG OF
WOOD PUTTY
SIDE VIEW
1 COLUMN CONNECTOR
LONG LADDER ASSEMBLY (END PIECE) x 1
SCALLOPED x 8
4 5/8"
STANDARD x 10
4 5/8"
77 1/8"
STANDARD 7 COLUMN CONNECTOR x 1
29 3/4"
SIDE VIEW
SCREWLESS 7 COLUMN CONNECTOR x 1
29 3/4"
SHORT LADDER ASSEMBLY (END PIECE) x 1
39 3/4"
STANDARD 10 COLUMN CONNECTOR x 3
WOOD SCREWS
42 5/16"
SCREWLESS 10 COLUMN CONNECTOR x 1
42 5/16"
SIDE VIEW
FINISH NAILS
Waterfall Wine Cellar Kit
Assembly GUIDE
Questions?
888.373.6057
or visit
Page 2
wineracksamerica.com
DOUBLE DEEP PACKAGE CONTENTS
LONG LADDER ASSEMBLY
(END PIECE) x 1
MIDDLE LADDER ASSEMBLIES
(*VARIOUS LENGTHS) x 9
STANDARD 10 COLUMN CONNECTOR x 2
42 5/16"
SCREWLESS 10 COLUMN CONNECTOR x 2
42 5/16"
SMALL BAG OF
WOOD PUTTY
SCREWLESS 7 COLUMN CONNECTOR x 2
SHORT LADDER ASSEMBLY
(END PIECE) x 1
SIDE VIEW
1 COLUMN CONNECTOR
SCALLOPED x 16
4 5/8"
STANDARD x 2
4 5/8"
HORIZONTAL TRIM PIECE x 3
SIDE VIEW
39 3/4"
77 1/8"
SIDE VIEW
77 1/8"
29 3/4"
22 1/4"
1 1/4" WOOD SCREWS
1. Find an open, flat area in which to work. Carefully
remove all components from the box and remove
banding with a utility knife. Check the parts list to
verify package contents
2. Arrange the ladders on the floor to form the
"stair step" design pictured. This will be the
back of your rack. The back of your rack will
depend on which direction you would like the
waterfall rack to descend. For example figure
1 shows the waterfall rack descending from
right to left.
Arrange the long end ladder so that the large
gap on the end of the ladder becomes the top
of the stair steps. This is the top of your rack.
* If you are assembling the Double Deep Waterfall
Rack please skip step 3 and use steps 4-6 for
assembling the front and back of your rack.
1
BEGIN WITH BACK
OF RACK
FINISH NAILS
Waterfall Wine Cellar Kit
Assembly GUIDE
Questions?
888.373.6057
or visit
wineracksamerica.com
Page 3
TOP
3. First attach the bottom 10 column connector
using the screws provided. Make sure that the
bottom of the connector is flush with the bottom
of the rack. Each vertical ladder piece should fit
snugly into the notches of the horizontal connector.
BEGIN WITH BACK
OF RACK
2
26
"
5/8
51
"
3/4
Next secure the middle 10 column and 7 column
connectors. The top edge of the middle 10 column
connector should be 26 5/8" from the bottom of
the rack, and the top edge of the middle 7 column
connector should be 51 3/4" from the bottom of
the rack. (figure 2)
4. Flip rack over and secure a standard 10 column connector to the bottom of your rack using the screws provided. Make
sure the standard connector is flush with the bottom of the rack. (figure 3)
5. Attach the middle screwless connectors so that the top edge of the middle 10 column connector is 26 5/8" from
the bottom of the rack, and the top edge of the middle 7 connector is 51 3/4" from the bottom of the rack. Make
sure the rack is flat on the floor while attaching the screwless connectors. (figure 3)
Secure the screwless connectors using wood glue and a finish nail gun to drive a finish nail through the connector
into each vertical ladder. (figure 4)
If you do not have a finish nail gun, drive one of the provided finish nails into each vertical ladder until it is flush.
Then, countersink the nail using a nail setter until the head of the nail is about 1/16" below the surface of the wood.
6. Fill the nail holes using the wood putty provided. Simply push the putty into each hole using your thumb and
wipe excess putty off the surface using a damp cloth.
FRONT OF RACK
or
finish nail
(included)
3
ATTACH SCREWLESS
CONNECTORS
4
SECURE WITH
FINISH NAILS
Waterfall Wine Cellar Kit
Assembly GUIDE
Questions?
888.373.6057
or visit
Page 4
wineracksamerica.com
7. Begin securing the 1-column connectors. The rack should still be flat on the floor and not standing upright.
* If you are assembling the Single Deep Waterfall Rack follow step 8 for the back of the rack and step 9 for
the front.
* If you are assembling the Double Deep Waterfall Rack please skip step 8 and follow step 9 for the front &
back of the rack.
8. Attach nine 1-column standard connectors to columns 1,2,3,4,5,6,8,9 & 10 using the screws provided. Make sure
that the top of the connector is flush with the top of the shorter vertical ladder assembly. The connector on column
1 should be flush with the top of the rack. (figure 5)
9. Attach one standard 1-column connector to column 1 using the screws provided. Make sure the top of the connector
is flush with the top of the rack.
Attach (8) scalloped 1-column connectors to columns 2,3,4,5,6,8,9 & 10 following the same process you used to attach
the screwless connectors in steps 5 & 6. (figure 6)
BACK OF RACK
5
ATTACH THE 1-COLUMN
CONNECTORS
FRONT OF RACK
6
ATTACH THE 1-COLUMN
SCALLOPED CONNECTORS
Waterfall Wine Cellar Kit
Assembly GUIDE
Questions?
888.373.6057
or visit
Page 5
wineracksamerica.com
10. Attach the (3) Horizontal Trim Pieces to the sides of the 1st, 7th and 10th column of the rack. (figure 7)
The Trim Pieces should fit snugly between the two vertical risers pieces on each vertical ladder, simply attach the
Trim Piece by putting a small finish nail or staple through each end of the Trim Piece securing it to both vertical risers.
(figure 8)
*If you have the Double Deep Waterfall rack you will need to use 3 finish nails or staples for each Trim Piece as the
vertical ladders on the Double Deep Waterfall Rack have three vertical risers instead of two. (figure 9)
7
ATTACH THE
TRIM PIECES
8
SECURE TRIM PIECES
USING FINISH NAILS
9
11. That’s it! Enjoy this beautiful rack with your favorite beverage. Pair with other rack styles for an ultimate cellar
storage look.
We would love to see your wine racks in use! Please feel free to
send any photos of your racks to photos@wineracksamerica.com
Once again, thank you for your business. Remember, customer
service is available to answer any questions Monday-Friday
7:00 am - 5:00 pm MST. Please feel free to contact us for any
wine storage needs.
WINERACKSAMERICA.COM
360 North 700 West Suite F • North Salt Lake, UT 84054
(toll free) 888-373-6057
(fax) 801-936-0534
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising