CyberPower UM CP1350PFCLCD
1
Power Switch
2
Power On Indicator
3
LCD module display
Used as the master on/off switch for equipment connected to the battery power supplied outlets.
This LED is illuminated when the utility power is normal and the UPS outlets are providing power, free of surges and spikes.
CP1350PFCLCD
CP1500PFCLCD
User’s Manual
High resolution and intelligent LCD display shows all the UPS information using icons and messages.
4
Display switch
The switch can be used to select the LCD display contents including Input Voltage, Output Voltage, and Estimated Run Time. The toggle
frequency is set to one time per 0.5 second. Press the switch to roll down the function menu. Pressing the switch for 2 seconds will turn the
K01-0000162-01
LCD display on or off while in AC/Utility power mode.
5
IMPORTANT SAFETY WARNINGS
Silence Alarm switch
The toggle frequency is set to one time per 0.5 second. Press the switch to roll up the function menu. Holding the switch for more than 2
seconds while running on battery will silence the buzzer.
(SAVE THESE INSTRUCTIONS)
This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit.
6
Control switch
7
USB Power Ports
8
Battery and Surge Protected Outlets
Press the Control switch for 3 seconds in AC/Utility Power Mode to perform a Self Test of the battery.
Read this manual thoroughly before attempting to unpack, install, or operate your UPS.
CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive
contaminants.
The USB Power ports provide 5V 1A power output.
(Please see specifications for acceptable temperature and humidity range).
CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery. Turn off and unplug the unit before
The unit has five battery powered/surge suppression outlets for connected equipment to ensure temporary uninterrupted operation of your
servicing the batteries. There are no user serviceable parts inside except for the battery.
equipment during a power failure. (DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum, sump pump or other
CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.
CAUTION! The UPS must be connected to an AC power outlet with fuse or circuit breaker protection.
grounded.
large electrical devices into the “Battery and Surge Protected Outlets”. The power demands of these devices may overload and
Do not plug into an outlet that is not
damage the unit.)
If you need to de-energize this equipment, turn off and unplug the unit.
CAUTION! To avoid electric shock, turn off the unit and unplug it from the AC power source before servicing the battery or installing a computer
9
Full-Time Surge Protection Outlets
The unit has five surge suppression outlets.
component.
CAUTION! Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment,
10
Circuit Breaker
Located on the back of the UPS, the circuit breaker serves to provide overload and fault protection.
ANSI/NFPA 75.
CAUTION! To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum branch circuit over current protection in
11
Serial/USB Ports to PC
The USB port allows connection and communication between the USB port on the computer and the UPS unit.
accordance with the National Electric Code, ANSI/NFPA 70.
DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support or medical
applications.
For more information please review
the “Definitions for Illuminated LCD Indicators” section below.
12
13
patient care.
DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an aquarium.
Communication Protection Ports
Communication protection ports will protect any standard modem, fax, telephone line, network or Ethernet connection (RJ11/RJ45).
DO NOT use in any circumstance that would affect the operation and safety of life support equipment, medical applications, or
Wiring Fault Indicator (red)
This LED indicator will illuminate to warn the user that a wiring problem exists, such as bad ground, missing ground or reversed wiring.
Condensation
If
this is illuminated, disconnect all electrical equipment from the outlet and have an electrician verify the outlet is properly wired. The unit will
from the aquarium can cause the unit to short out.
not provide surge protection without being plugged into a grounded and properly wired wall outlet.
14
INSTALLING YOUR UPS SYSTEM
Coax/Cable/DSS Surge Protection
The Coax/Cable/DSS protection ports will protect any cable modem, CATV converter, or DSS receiver.
15
Outlets Designed for AC Adapters
The unit has two outlets spaced to allow AC power adapter blocks to be plugged into the UPS without blocking adjacent outlets.
INTRODUCTION
Thank you for selecting a CyberPower Systems UPS product. This UPS is designed to provide unsurpassed power protection, operation and
performance during the lifetime of the product.
REPLACING THE BATTERY
Replacement of batteries located in an OPERATOR ACCESS AREA.
1.
UNPACKING
When replacing batteries, replace with the same number of the following battery: CyberPower / RB1270X2A for the CP1350PFCLCD;
CyberPower / RB1280X2A for the CP1500PFCLCD.
Inspect the UPS upon receipt. The box should contain the following:
2.
(a) UPS unit (b) User’s manual (c) Telephone cable (d) PowerPanel® Personal Edition software CD (e) Coaxial cable
as chains, wrist watches, and rings. High energy conducted through these materials could cause severe burns.
(f) USB A+B type cable (g) Warranty registration card (h) Function Setup Guide
SUPPORTS Active PFC POWER SUPPLIES
This CyberPower UPS system supports High Efficiency power supplies with Active Power Factor Correction (Active PFC). Active PFC is used to
®
improve the efficiency of power delivery. The current US Energy Star Program Requirements for Computers (version 5.0) mandates Active PFC
CAUTION! Risk of Energy Hazard, 24 V, maximum 9 Ampere-hour battery. Before replacing batteries, remove conductive jewelry such
3.
CAUTION! Do not dispose of batteries in a fire. The batteries may explode.
4.
CAUTION! Do not open or mutilate batteries. Released material is harmful to the skin and eyes. It may be toxic.
CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING
TO LOCAL REGULATIONS.
for all power supplies over 100 watts. Additionally, programs such as 80 Plus® are often used to identify high efficiency power supplies with Active
BATTERY REPLACEMENT PROCEDURE:
PFC.
1.
Turn off and unplug all connected equipment.
OVERVIEW
2.
Turn the UPS off and unplug it from the AC power source.
The CP1350PFCLCD/CP1500PFCLCD provides complete power protection from utility power that is not
3.
Turn the UPS on its side.
always consistent. The CP1350PFCLCD/CP1500PFCLCD features 1030 Joules of surge protection. Both
4.
Remove the front panel retaining screws located on the bottom of the UPS.
units provide long lasting battery backup during power outages with maintenance free batteries. The
5.
Slide the battery compartment cover (front panel) completely off of the unit.
CP1350PFCLCD/CP1500PFCLCD ensures consistent power to your computer system and includes software
6.
Remove the batteries from the compartment.
that will automatically save your open files and shutdown your computer system during a utility power loss.
7.
Disconnect the battery wires from the batteries.
8.
CP1350PFCLCD: Install the replacement batteries by connecting the red wire (+) and black wire (-) to the same color connectors from the
AUTOMATIC VOLTAGE REGULATOR
battery pack.
The CP1350PFCLCD/CP1500PFCLCD stabilizes inconsistent utility power voltage to nominal levels that are safe for equipment. Inconsistent
CP1500PFCLCD: Install the replacement batteries by connecting the wire bundle (composed of one red wire and one black wire) to the
connector from the battery pack.
incoming utility power may be damaging to important data files and hardware, but with Automatic Voltage Regulation (AVR), damaging voltage
levels are corrected to safe levels.
AVR automatically increases low utility power and decreases high utility power to a consistent and safe
110/120 volts. If incoming utility voltage drops below 90 volts, or exceeds 140 volts the units automatically switch to battery back-up power.
HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT
9.
Put the batteries back into the compartment.
10.
Slide back the battery compartment cover and tighten the retaining screws.
11.
Recharge the UPS for 8-16 hours to fully charge the battery.
CP1350PFCLCD
1. Ensure that the equipment plugged into the outlet does not exceed the UPS unit’s rated capacity (1350VA/810W for CP1350PFCLCD,
1500VA/900W for CP1500PFCLCD).
If the rated capacities of the unit are exceeded, an overload condition may occur and cause the UPS
unit to shut down or the circuit breaker to trip.
2. There are many factors that can affect the amount of power that your computer system will require.
It is suggested that the load placed on
the battery outlets not exceed 80% of the unit’s capacity.
CP1500PFCLCD
HARDWARE INSTALLATION GUIDE
1. Your new UPS may be used immediately upon receipt. However, after receiving a new UPS, to ensure the
battery’s maximum charge capacity, it is recommended that you charge the battery for at least 8 hours.
Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the
battery will automatically charge whether the UPS is turned on or off.
2. Note: This UPS is designed with a safety feature to keep the system from being turned on during shipment.
The first time you turn the UPS on, you will need to have it connected to AC power or it will not power up.
REMINDER:
Batteries are considered HAZARDOUS WASTE and must be disposed of properly.
Most retailers that sell lead-acid batteries
collect used batteries for recycling, as required by local regulations.
3. With the UPS unit turned off and unplugged, connect your computer, monitor, and any other peripherals requiring battery backup into the
battery power supplied outlets. DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum, sump pump or other large
electrical devices into the “Battery and Surge Protected Outlets”. The power demands of these devices may overload and damage
DEFINITIONS FOR ILLUMINATED LCD INDICATORS
1. ONLINE: The UPS is supplying utility power to connected equipment.
the unit.
4. To protect a fax, phone or modem, connect a telephone cable or network cable from the wall jack outlet to the IN
2. BATTERY: During a severe brownout or blackout, this icon appears and an alarm
jack of the UPS. Connect a telephone cable or network cable from the OUT jack of the UPS to a fax machine,
sounds (two short beeps followed by a pause) to indicate the UPS is operating from
telephone, modem, or network devices.
its internal batteries. During a prolonged brownout or blackout, the alarm will beep
5. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet).
Make sure the wall branch outlet is
rapidly every 1/2 second (and the BATT.CAPACITY meter shows one 20% capacity
protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. air
segment shaded. The capacity depends on how much load added and the runtime
conditioner, copier, etc…). The warranty prohibits the use of extension cords, outlet strips, and surge strips.
left.) to indicate the UPS’s batteries are nearly out of power. You should save files
6. Press the power switch to turn the unit on.
The Power On indicator light will illuminate and the unit will “beep”.
and turn off your equipment immediately or allow the software to shut the system down.
If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and unplug at
3. Energy-Saving: The UPS in energy-saving bypass mode. See “CyberPower
least one piece of equipment from the battery power supplied outlets.
GreenPower UPSTM Technology” section for more information.
Make sure the circuit breaker is depressed and then turn the UPS on.
7. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.
4. LOAD capacity / Sensitivity setup: This meter displays the approximate output
8. To store the UPS for an extended period, cover it and store with the battery fully charged. While in storage, recharge the battery every three
load level (in 20% increments) of the UPS battery outlets. It can also be sensitivity
setup meter if you are in programming mode. It is to control the sensitivity of the UPS to switch to Battery Mode by selecting UPS shutdown
months to ensure battery life.
9. Insure the wall outlet and UPS are located near the equipment being attached for proper accessibility.
voltage range. When the sensitivity is increased, the UPS will switch to Battery Mode with less input power variation.
5. BATTERY capacity: This meter displays the approximate charge level (in 20% increments) of the UPS’s internal battery. During a
BASIC OPERATION
blackout or severe brownout, the UPS switches to battery power, the BATTERY icon appears, and the charge level decreases.
6. FAULT: This icon appears if there is a problem with the UPS. Press the POWER button to turn off the UPS.
F01: Battery Mode or AC/Utility Power Mode Overload fault (Turn on the UPS again.)
DESCRIPTION
F02: Battery Output Short fault (Turn on the UPS again.)
F03: Charger Fault (Contact CyberPower Systems for support.)
F04: Internal Fault (Contact CyberPower Systems for support.)
7. OVER LOAD: This icon appears and an alarm sounds to indicate the battery-supplied outlets are overloaded. To clear the overload,
unplug some of your equipment from the battery-supplied outlets until the icon turns off and the alarm stops.
8. SCHEDULE: Users can setup the schedule to turn on and shut down the computer and UPS through PowerPanel® Personal Edition
software. The LCD display will show how much time is left before the UPS will turn back on or shut down.
9. ESTIMATED RUNTIME: This displays the run time estimate of the UPS with current battery capacity and load.
10. OUTPUT meter: This meter measure, in real time, the AC voltage that the UPS system is providing to the computer, such as normal AC
line mode, AVR mode, and battery backup mode. (Note: The OUTPUT meter shows the status of the battery backup outlets in terms of load,
Limited Warranty and Connected Equipment Guarantee
frequency, and voltage.)
11. INPUT meter: This meter measures the AC voltage that the UPS system is receiving from the utility wall outlet. The UPS is designed,
through the use of automatic voltage regulation, to continuously correct output voltage to connected equipment to a safe 110/120 voltage
Read the following terms and conditions carefully before using the CyberPower CP1350PFCLCD/CP1500PFCLCD (the “Product”).
output range. In the event of a complete power loss, severe brownout, or over-voltage, the UPS relies on its internal battery to supply
By using the Product you consent to be bound by and become a party to the terms and conditions of this Limited Warranty and
consistent 110/120 output voltage. The INPUT voltage meter can be used as a diagnostic tool to identify poor-quality input power.
Connected Equipment Guarantee (together referred to as this “Warranty”). If you do not agree to the terms and conditions of this
12. EVENT: This meter records the number of power outages.
Warranty, you should return the Product for a full refund prior to using it.
13. MUTE: This icon appears whenever the UPS is in silent mode. The alarm does not beep during silent mode until the battery reaches low
capacity.
Who is Providing this Warranty?
14. AVR (Automatic Voltage Regulation): This icon appears whenever your UPS is automatically correcting low AC line voltage without
CyberPower Systems (USA), Inc. (“CyberPower”) provides this Limited Warranty.
using battery power. This is a normal, automatic operation of your UPS, and no action is required on your part.
What Does This Warranty Cover?
This warranty covers defects in materials and workmanship in the Product under normal use and conditions.
For more information about functions setup, please refer to the Function Setup Guide.
It also covers
equipment that was connected to the Product and damaged because of the failure of the Product.
TROUBLESHOOTING
Problem
What is the Period of Coverage?
Possible Cause
Circuit breaker button is
projecting from the back of the
unit.
Solution
Circuit breaker has tripped due to an
overload.
Turn the UPS off and unplug at least one piece of
equipment. Wait 10 seconds, reset the circuit breaker by
depressing the button, and then turn the UPS on.
Battery not fully charged.
Recharge the battery by leaving the UPS plugged in.
Battery is worn out.
Contact CyberPower Systems about replacement batteries
at tech@cyberpowersystems.com
This warranty covers the Product for three years and connected equipment for as long as you own the Product.
Who Is Covered?
This warranty only covers the original purchaser. Coverage ends if you sell or otherwise transfer the Product.
How Do You Get Warranty Service?
The UPS does not perform
expected runtime.
The UPS will not turn on.
®
PowerPanel Personal Edition is
inactive (all icons are gray).
The USB power ports are not
providing power to the connected
devices.
1.
Before contacting CyberPower, identify Your Product model number, the Purchase Date, and each item of Connected
Equipment (E.G. Computer tower, Computer Monitor, Ink Jet Printer, Cable Modem, etc).
2.
Visit our web site at http://www.cpsww.com/support or Call us at (877) 297-6937.
3.
If your product requires warranty service you must provide a copy of your dated purchase receipt or invoice.
The on/off switch is designed to
prevent damage from rapidly turning
it off and on.
Turn the UPS off. Wait 10 seconds and then turn the UPS
on.
The unit is not connected to an AC
outlet.
The unit must be connected to a 110/120V 60Hz outlet.
The battery is worn out.
Contact CyberPower Systems about replacement batteries
at tech@cyberpowersystems.com
Mechanical problem.
Contact CyberPower Systems at
tech@cyberpowersystems.com
The USB / serial cable is not
connected.
Connect the USB / serial cable to the UPS unit and an open
USB / serial port on the back of the computer. You must
use the cable that came with the unit.
The USB / serial cable is connected
to the wrong port.
Check the back of the computer for an additional USB /
serial port. Move the cable to this port.
The unit is not providing battery
power.
Shutdown your computer and turn the UPS off. Wait 10
seconds and turn the UPS back on. This should reset the
unit.
How Long Do I Have To Make A Claim?
The serial cable is not the cable that
came with the unit.
Please use the serial cable that came with the unit for the
software.
What Will We Do To Correct Problems?
The USB power port has Over
Current Protection design. When the
total current of connected devices is
over 1A, the USB power ports will
stop providing power to the
connected devices.
Turn the UPS off and unplug at least one piece of device
connected to the USB power port and then turn the UPS on.
How Do You Open A Connected Equipment Claim?
1.
Call us at (877) 297-6937 or write to us at Cyber Power Systems (USA), Inc., 4241 12th Ave. E., STE 400, Shakopee, MN
55379, or send us an e-mail message at claims@cpsww.com for instructions, within 10 days of the occurrence.
2.
When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have
information on all applicable insurance or other resources of recovery/payment that are available to the Initial Customer and
Request a Claim Number.
3.
You must provide a dated purchase receipt (or other proof of the original purchase) and provide a description of the damage to
your connected equipment.
4.
Pack and ship the product to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost estimate for the
damage to the Connected Equipment, and all claim forms that CyberPower provides to you. Show the Claim Number on the
shipping label or include it with the product. You must prepay all shipping costs, you are responsible for packaging and
shipment, and you must pay the cost of the repair estimate.
All claims must be made within ten days of the occurrence.
CyberPower will inspect and examine the Product.
If the Product is defective in material or workmanship, CyberPower will repair or replace it at CyberPower's expense, or, if
CyberPower is unable to or decides not to repair or replace the Product (if defective) within a reasonable time, CyberPower will refund
to you the full purchase price you paid for the Product (purchase receipt showing price paid is required).
If it appears that our Product failed to protect any equipment plugged into it, we will also send you forms for making your claim for the
connected equipment. We will repair or replace the equipment that was damaged because of the failure of our Product or pay you
Additional troubleshooting information can be found under “Support” at www.CPSww.com
the fair market value (NOT REPLACEMENT COST) of the equipment at of the time of the damage. We will use Orion Blue Book, or
another a third-party valuation guide, or eBay, craigslist, or other source to establish that amount. Our maximum liability is limited to
$425,000 for the CP1350PFCLCD and $500,000 for the CP1500PFCLCD.
TECHNICAL SPECIFICATIONS
Who Pays For Shipping?
Model
CP1350PFCLCD
CP1500PFCLCD
Capacity
1350VA / 810W
1500VA / 900W
We pay when we send items to you; you pay when you send items to us.
What isn’t covered by the warranty?
1.
Nominal Input Voltage
120V
Input Frequency
57 Hz to 63 Hz
On-Battery Output Voltage
120Vac ± 5%
This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of the Product or any
data that is lost as a result of the failure or the restoration of data or records, or the reinstallation of software.
2.
This Warranty does not cover or apply to: misuse, modification, operation or storage outside environmental limits of the Product
or the equipment connected to it, nor for damage while in transit or in storage, nor if there has been improper operation or
maintenance, or use with items not designed or intended for use with the Product, such as laser printers, appliances, aquariums,
medical or life support devices, etc.
Transfer Time
4ms Typical
Max. Load for UPS Outlets (5 Outlets)
What are the Limitations?
1350VA / 810W
1500VA / 900W
The sole and exclusive remedies of the Initial Customer are those provided by this Warranty.
1.
Max. Load for Full-Time Surge Protection outlets
(10 Outlets)
This Warranty does not apply unless the Product and the equipment that was connected to it were connected to properly wired
and grounded outlets (including compliance with electrical and safety codes of the most current electrical code), without the use
12 Amp
of any adapters or other connectors.
2.
On-Battery Output Wave Form
Adaptive Sinewave
Operating Temperature
+ 32°F to 104° F / 0° C to 40° C
The Product must have been plugged directly into the power source and the equipment connected to the Product must be
directly connected to the Product and not “daisy-chained” together in serial fashion with any extension cords, another Product
or device similar to the Product, surge suppressor, or power tap. Any such installation voids the Limited Warranty.
3.
Operating Relative Humidity
0 to 90% non-condensing
Size (L x W x H)
14.2" x 3.9" x 10.4" (361 x 99 x 264 mm)
The Product and equipment connected to it must have been used properly in a suitable and proper environment and in
conformance with any license, instruction manual, or warnings provided with the Product and the equipment connected to it.
4.
The Product must have been used at all times within the limitations on the Product’s VA capacity.
The Product was designed to eliminate disrupting and damaging effects of momentary (less than 1ms) voltage spikes or impulses
Net Weight
20.3lbs / 9.2kg
24.7lbs / 11.2kg
Battery Type
CyberPower / RB1270X2A
CyberPower / RB1280X2A
Typical Battery Recharge Time
8 hours from total discharge
from lightning or other power transients. If it can be shown that a voltage spike lasting longer than 1ms has occurred, the occurrence
will be deemed outside the rated capabilities of the Product and the Limited Warranty is void. CyberPower Does Not Cover or
Undertake Any Liability in Any Event for Any of the Following:
1.
2.
Typical Battery Life
3 to 6 years, depending on number of discharge/recharge cycles
Recommended Battery
Sealed Maintenance Free Lead Acid Battery
Safety Approvals
UL1778, CSA C22.2 No 107.3, FCC/DoC Class B
Loss of or damage to data, records, or software or the restoration of data or records, or the reinstallation of software.
Damage from causes other than AC Power Line Transients, spikes, or surges on properly installed, grounded and
code-compliant 120 volt power lines in the United States and Canada; transients, surges or spikes on standard telephone land
lines, PBX telephone equipment lines or Base 10T Ethernet lines, when properly installed and connected. (This exclusion
EMI
Filter
transients in such transmission.)
3.
4.
SYSTEM FUNCTIONAL BLOCK DIAGRAM
Input
applies, for example, to fluctuations in data transmission or reception, by CATV or RF transmission or fluctuations, or by
Damage from any circumstance described as excluded above with respect to the Product.
Damages from fire, flood, wind, rain, rising water, leakage or breakage of plumbing, abuse, misuse or alteration of either the
product or the Connected Equipment.
Surge
Suppressor
AVR
Output
5.
CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee.
CyberPower excludes any liability for direct, indirect, special, incidental or consequential damages, whether for damage to or
loss of property [EXCEPT FOR (AND ONLY FOR) the specific limited agreement of CyberPower to provide certain warranty
Charger
AC/DC
benefits regarding "Connected Equipment" under this Warranty], loss of profits, business interruption, or loss of information or
Inverter
data. NOTE: Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages, so the
Normal Mode
above limitation may not apply to you.
Battery Mode
6.
Battery
The Product is not for use in high-risk activities or with aquariums. The Product is not designed or intended for use in hazardous
environments requiring fail-safe performance, or for use in any circumstance in which the failure of the Product could lead
directly to death, personal injury, or severe physical or property damage, or that would affect operation or safety of any medical
CYBERPOWER GREENPOWER UPS™ TECHNOLOGY
or life support device (collectively, "High Risk Activities"). CyberPower expressly disclaims any express or implied warranty of
fitness for High Risk Activities or with aquariums. CyberPower does not authorize use of any Product in any High Risk Activities
Advanced Energy-Saving Patented Bypass Technology
or with Aquariums. ANY SUCH USE IS IMPROPER AND IS A MISUSE OF THE PRODUCT.
CyberPower’s patented GreenPower UPS™ with Bypass Technology reduces UPS energy costs by up to
75% compared to conventional UPS models. Even when utility power is normal, conventional UPS models
Where Can I Get More Information?
constantly pass power through a transformer. By contrast, under normal conditions the advanced circuitry
The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded.
of a GreenPower UPS™ bypasses the transformer. As a result, the power efficiency is significantly
CyberPower is the warrantor under this Limited Warranty.
increased while decreasing waste heat, using less energy, and reducing energy costs.
For further information please feel free to contact CyberPower at CyberPower Systems (USA), Inc. 4241 12th Ave E., STE 400,
When an abnormal power condition occurs, the GreenPower UPS™ automatically runs power through its
Shakopee, MN 55379; call us at (877) 297-6937; or send us an e-mail message at claims@cyberpowersystems.com.
transformer to regulate voltage and provide “safe” power. Since utility power is normal over 88% of the time, the GreenPower UPS™
operates primarily in its efficient bypass mode.
CyberPower Systems encourages environmentally sound methods for disposal and recycling of its UPS products.
Please dispose and/or recycle your UPS and batteries in accordance to the local regulations of your state.
The GreenPower UPS™ is also manufactured in accordance with the Restriction on Hazardous Substances (RoHS) directive making
it one of the most environmentally-friendly on the market today.
All rights reserved. Reproduction without permission is prohibited.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising