Quick Start Guide - LBV1511 Series HD Security Bullet Camera

Quick Start Guide - LBV1511 Series HD Security Bullet Camera
Contents
•
•
•
•
IR Night Vision Camera*
Mounting Kit*
60ft BNC / Power Extension Cable*
Multi-Camera Power Adapter**
Resources
Need Help?
Visit us online for up-to-date software and complete
instruction manuals
* Per camera in multi-camera packs.
** A multi-camera power adapter that provides power to multiple cameras or individual power
adapters may be provided, depending on product configuration.
HD WEATHERPROOF
NIGHT VISION SECURITY CAMERA
Quick Start Guide
English Version 1.0
WARNING - A REGULATED power supply is REQUIRED for use with this
camera. Use of a non-regulated, non-conforming power supply can damage
this product and voids the warranty.
Warning/Caution
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use of the product and handle
with care.
• Do not disassemble the cameras.
• Do not point the cameras directly towards the sun or a source of
intense light.
• Use only the supplied regulated power supply. Use of a nonregulated, non-conforming power supply can damage this
product and voids the warranty.
• Periodic cleaning may be required. Use a damp cloth only. Do
not use harsh cleaners or aerosol cleaners.
Installation Tips
• Point the cameras where there is the least amount of obstructions
(i.e. tree branches).
• Install the cameras where they are difficult for vandals to reach.
• Secure cabling so that it is not exposed or easily cut.
• Cameras rated for outdoor use. Installation in a sheltered
location recommended.
Dimensions
1
Go to www.lorextechnology.com
2
Search the model number of your product
3
Click on your product in the search results
4
Click on the Downloads tab
THE FOLLOWING RESOURCES ARE ALWAYS AT
YOUR FINGERTIPS
Product Information
Specification Sheets
User Manuals
Software Upgrades
Quick Start Guides
Firmware Upgrades
70mm / 2.7”
70mm / 2.7”
154mm / 6.0”
Copyright © 2015 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right to modify product
design, specifications and prices, without notice and without incurring any obligation. E&OE
LBV1511_SERIES_TRIFOLDQSG_EN_R1
LBV1511 SERIES
Installing the Cameras
Connecting the Cameras
ATTENTION - Test each camera prior to selecting a permanent mounting
location by temporarily connecting the camera(s) and cables to the DVR.
To DVR:
To Camera:
Cable Extension Options
Extend the cable run for your camera depending on the cable type
used. Additional extension cables sold separately. See table below:
Before installing the cameras:
Option
• Decide whether to run the cables
through the wall / ceiling (drilling
required) or along the wall / ceiling.
1
Lorex model MCBL-60BNCU BNC Cable
(included with camera)
60ft / 18m
2
‘RG59’ or ‘Coax’ or ‘Coaxial BNC’
Siamese (Video and Power)
300ft / 92m
3
‘RG59’ or ‘Coax’ or ‘Coaxial BNC’
(Video Only2)
800ft / 242m
• If you run the cables along the wall
/ ceiling, you must run the cable
through the cable notch on the base.
This will keep the camera base flush
to the surface when mounted.
To install the cameras:
Female Power
Male Power
Cable Notch
1. Set the camera in the desired mounting position and
mark holes for screws through the camera base.
2. Drill the holes, then feed the cable through the
mounting surface or cable notch.
NOTE: Insert the included drywall anchors if
installing the camera in drywall.
3. Mount the camera stand to the surface using the
provided screws. Make sure all screws are fastened
tightly.
*
2. Connect the BNC connector to
the video input of your DVR.
3. Connect the power connectors
to the multi-camera power
adapter. OR Connect each
camera to an individual power
adapter.
Multi-Camera Power Adapter
A multi-camera power adapter that provides power to multiple
cameras or individual power adapters may be provided,
depending on product configuration. Connect multiple cameras to
the power splitter cable.
1. The extension cable must be a single stretch of cable between the DVR
and camera. You cannot connect multiple extension cables to each other.
2. For cable runs above 300ft / 92m (option 3), you must connect the
power adapter directly to the camera, rather than at the end of the
extension cable.
3. Indicators that your cable run may be too long:
• Video is permanently black & white (even during day time)
• Video is unclear, soft, or distorted
4. For more information on extension cables, visit
www.lorextechnology.com/support.
Troubleshooting
Problem
•Ensure the camera is connected to a compatible
Series DVR. 1080p cameras are compatible
with 1080p HD DVR recorders. 720p cameras
are compatible with 720p & 1080p HD DVR
recorders.
•Ensure your TV is on the correct input channel.
Common terms of an input channel: INPUT, AV
CHANNEL, LINE1, LINE2, AUX.
•Ensure your DVR is properly connected to your
TV / Monitor.
•Ensure connections are properly connected.
•Ensure the camera power supply is plugged in.
Picture is too bright
•Ensure your camera isn’t pointed directly at a
source of light (e.g. sun or spot light).
•Move your camera to a different location.
Picture is too dark
•Check the brightness and contrast settings of
the DVR or monitor.
Night vision is not
working
•The night vision activates when light levels
drop. The area may have too much light.
Picture is not clear
•Check the camera lens for dirt, dust,
spiderwebs. Clean the lens with a soft, clean
cloth.
•Make sure that the cable run is within the
limitations specified in the section ‘Cable
Extension Options’.
Bright spot in video
when viewing camera
at night
•Night vision reflects when pointing a camera
at a window. Move the camera to a different
location.
A
Setup Diagram
A) Turn the adjustment ring to tighten / loosen the stand
connection. Adjust the camera’s horizontal position.
C
HD DVR
B) Loosen lower screw with a philips
head screwdriver (not included) to
adjust the camera’s vertical position.
C) Loosen upper screw with
philips head screwdriver (not
included) to rotate the camera
housing.
*Disclaimer: The color of the camera housing may appear differently than the actual unit.
ATTENTION - This camera includes an Auto Mechanical IR Cut Filter. When
the camera changes between Day/Night viewing modes, an audible clicking
noise may be heard from the camera. This clicking is normal, and indicates
that the camera filter is working.
Solution
No picture / signal
4. Set the position and angle of the camera.
B
Max Cable Run
Distance
Notes:
BNC
1. Connect the BNC and
power connectors to the
camera.
Cable Type
LBV1511_SERIES_TRIFOLDQSG_EN_R1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising