datasheet for AMEPR15D
Series AMEPR15D-AZ
up to 1A | AC-DC LED driver
FEATURES:





AC-DC Constant current LED Driver
Input range 90-264VAC/47-440Hz
High Efficiency up to 83%
Operating temperature -20 to 80°C
Total Harmonic Distortion 20%




Over Temperature Protection
IP20 Case
Active PFC with TRIAC dimmable
SCP, Over Load Protection
Models
Single output
Model
Max
Output
Power
(W)
Output
Voltage
Range
(V)
No Load
Output
Voltage
(V max.)
15
15.8
18
16.8
15
36-50
30-48
24-36
12-24
8-15
62
62
52
34
23
AMEPR15D-5030AZ
AMEPR15D-4835AZ
AMEPR15D-3650AZ
AMEPR15D-2470AZ
AMEPR15D-15100AZ
Output
Current
(A)
0.3
0.35
0.5
0.7
1
Input Voltage
(VAC/Hz)
Input Voltage
(VDC)
Efficiency
(%)
90-264/47-440
90-264/47-440
90-264/47-440
90-264/47-440
90-264/47-440
120-370
120-370
120-370
120-370
120-370
83
83
82
81
80
Exceeding the maximum output power will permanently damage the converter
Model Nomenclature Options:
Add Suffix “-UD”
Add Suffix “-110D”
Add Suffix “-220D”
Universal AC input 90-264VAC(no TRIAC dimming with this option),IP20
AC input 90-135VAC, IP20
AC input 180-264VAC, IP20
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at
rated output load unless otherwise specified.
Input Specifications
Parameters
Inrush current <2ms
Leakage current
AC current
Power Factor
Conditions
Typical
115VAC
230VAC
115VAC
230VAC
115VAC
230VAC
115VAC
230VAC
10
20
0.2
0.25
0.23
0.1
Maximum
Units
A
mA
A
0.9
0.9
250V/1A
External fuse
Start up time
200
ms
Output Specifications
Parameters
Conditions
Typical
Current accuracy
±5
Line regulation
LL-HL
±7
Load regulation
0-100% load
±5
20MHz Bandwidth
1
Ripple & Noise
Hold-up time
1
Minimum Load Voltage
See the models table
Tested with 0.1µF (M/C) or (C/C) and 47µF (E/C) parallel capacitors at the end.
www.aimtec.com
F 052.1e R3.A
Tel: +1 514 620 2722
1 of 4
Maximum
Units
%
%
%
V p-p
ms
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMEPR15D-AZ
up to 1A | AC-DC LED driver
Isolation Specifications
Parameters
Conditions
Tested I/O voltage
Isolation Resistance
Typical
3sec
Maximum
Units
3000
VAC
M
>1000
General Specifications
Parameters
Conditions
Switching frequency
Over load protection
Over voltage protection
Short circuit protection
Short circuit restart
Over temperature protection
Operating temperature
Maximum case temperature
Storage temperature
Temperature coefficient
Cooling
Humidity
Case material
Wires
Weight
Dimensions (L X H X W)
MTBF
Typical
Maximum
65
110% of Iout
110% of Vout
Continuous
Auto recovery
>105°C
-20 to +80
With derating over 55°C
KHz
o
100
-40 to +95
±0.02
Free air convection
95
Plastic
UL1015 20AWG * 10CM
200
133 x 33 x 30mm
>400,000 hrs (MIL-HDBK-217F at +25°C)
Units
C
C
o
C
% / oC
o
% RH
g
Environment Approval
Test
Shock
Vibration
Parameters
Wave form
Acceleration amplitude
Bump duration
Converter operation
Number of bumps
Test mode
Displacement
Acceleration
Converter operation
Conditions
Half sine wave
5gn
30 ms
Before and after test, body mounted (on chassis)
18 (3 in each direction for every axis)
Sweep sine, 10-100Hz, speed 0.05Hz/s
1 mm
3g, 3 loops 30min one cycle, 3h total, every axis tested
Before and after test, body mounted (on chassis)
Safety Specifications
Parameters
Agency approvals
Standards
www.aimtec.com
F 052.1e R3.A
cULus, CE, CB pending
EN61347, IEC62384, UL8750, UL60950-1, EN55015
Tel: +1 514 620 2722
2 of 4
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMEPR15D-AZ
up to 1A | AC-DC LED driver
Dimensions
Temperature graph
Free Air Convection
55 º C
Output Power %
100
80
Safe Operating Area
60
40
20
0
- 25
- 20
0
20
40
60
80
100
Ambient Temperature º C
www.aimtec.com
F 052.1e R3.A
Tel: +1 514 620 2722
3 of 4
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMEPR15D-AZ
up to 1A | AC-DC LED driver
Triac Dimming Feature
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified.5..Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 5. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet.
www.aimtec.com
F 052.1e R3.A
Tel: +1 514 620 2722
4 of 4
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising