Q-Logic 5000/9000 Switch User manual

SANbox 5000/9000 Series

Stackable Chassis Switch

Stacking Cable Instructions

These instructions describe the interconnection of SANbox ® 5000 Series switches and SANbox 9000

Series switches using XPAK-XPAK and XPAK-X2 stacking cables. SANbox 5000 Series switches have

10-Gbps 1 XPAK ports. SANbox 9000 Series 10-Gbps I/O blades have X2 ports. Connection combinations are as follows:

Switch to Switch

SANbox 5000 to SANbox 5000

SANbox 5000 to SANbox 9000

SANbox 9000 to SANbox 9000

Cable Type

XPAK-XPAK

XPAK-X2

X2-X2

Cable Lengths

3 inch, 9 inch, 2 meter

18 inch, 2 meter

18 inch

Remove XPAK and X2 Port Covers

Both SANbox 5000 and SANbox 9000 Series switches come with port covers on the XPAK and X2 ports respectively. Before installing the XPAK cables, remove the port covers. To remove the port covers for either switch model, insert a small flathead screwdriver in the cover slot and gently pry the cover from the port.

SANbox 5000 Series SANbox 9000 Series

1 SANbox 5800 series XPAK ports can be licensed for 20-Gbps. SANbox 5800 Series XPAK ports that have been upgraded to

20-Gbps are fully compatible with XPAK and X2 ports running at 10-Gbps, and will auto-negotiate to match the speed of the slower device.

50326-06 A 1

*50326-06 A*

SANbox 5000/9000 Series Stackable Chassis Switch Stacking Cable Instructions

D

Connect SANbox 5000 Series Switches

Using an XPAK-XPAK connector, install the cable connectors with the circuit board toward the mid line of the respective switch faceplates. The cable connector will fit only one way. When installing the

3-inch XPAK cable, insert the cable connectors into the XPAK ports at the same time as shown.

Circuit Board

Connect SANbox 5000 and 9000 Series Switches

To connect a SANbox 5000 Series switch and a SANbox 9000 Series switch, use an XPAK-X2 cable.

Install the XPAK connector in the SANbox 5000 series switch port with the circuit board toward the mid line of the switch. Install the X2 connector in the SANbox 9000 switch port with the circuit board on the left. SANbox 5800 Series XPAK ports that are licensed for 20-Gbps will auto-negotiate to interoperate with the 10-Gbps SANbox 9000 Series X2 ports.

To connect two SANbox 9000 switches, use an X2-X2 cable. Install the cable connectors in the respective switch ports with the circuit boards on the left. The cable connector will fit only one way.

D

Corporate Headquarters QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656 949.389.6000 www.qlogic.com

Europe Headquarters QLogic (UK) LTD. Quatro House Lyon Way, Frimley Camberley Surrey, GU16 7ER UK +44 (0) 1276 804 670

© 2008 QLogic Corporation. Specifications are subject to change without notice. All rights reserved worldwide. QLogic, QLogic logo and SANbox are trademarks or registered trademarks of

QLogic Corporation. All other brand and product names are trademarks or registered trademarks of their respective owners. Information supplied by QLogic Corporation is believed to be accurate and reliable. QLogic Corporation assumes no responsibility for any errors in this brochure. QLogic Corporation reserves the right, without notice, to make changes in product design or specifications.