VX21 22 23 EU

VX21 22 23 EU
CAT.EUS70-23 A -UK
Direct Operated
2 Port Solenoid Valve
For Water, Oil, Steam, Air
New Series VX21/22 /23
Reduction of
power consumption
(DC specification)
4.5 W
4.
8 W 7 W
10.
0.5 W
11.5
1.5 W 10.5
6 W
Low power consumption type:
0. W
0.8
(Held at 24 VDC)
New VX Series now on sale!
Solenoid valves for various fluids used in a wide variety of
Improvement
Impr
vement of corrosion
corrosion
resistance
Reduction of power
consumption (DC specification)
VX21: 6 W 4.5 W
VX22: 8 W 7 W
VX23: 11.5 W 10.5 W
Special magnetic
material
mater adopted
losure:
Enclosure:
Equivalent to IP65
Low
w power
power consumption
(Held at 24 VDC)
type: 0.8 W
Flame resistance
UL94V-0 conformed
ormed
With mounting threads
on the bottom
Flame resistant mold coil material
mater
A dedicated bracket
br
is available.
Low
w noise
construction
Special construction
constr
enables to reduce
the metal noise.
noise (DC specification)
Installation example
Improvement
Impr
vement of
maintenance performance
performance
Maintenance is performed
perf med easily due to the threaded assembly.
assemb
Bracket∗
∗ For orifice sizes ø2, ø3, ø4.5, and ø6
Direct Operated 2 Port Solenoid Valve
New Series VX21/ 22 / 23
For Water, Oil, Steam, Air
Normally Closed (N.C.)
Model
VX21
VX22
VX23
Orifice size
2 mmø 3 mmø 4.5 mmø 6 mmø 8 mmø 10 mmø
Port size
—
—
—
1/8, 1/4
—
1/4, 3/8
—
—
—
—
—
1/2
—
1/4, 3/8
—
—
—
—
—
1/2
Material
Seal
Body
NBR
Brass
FKM
Stainless
EPDM
steel
PTFE
Normally Open (N.O.)
Model
VX21
VX22
VX23
VX21
VX22
VX23
Features 1
Orifice size
2 mmø
3 mmø
4.5 mmø
6 mmø
—
—
—
1/8, 1/4
1/4, 3/8
—
1/4, 3/8
—
NBR
Brass
Stainless FKM
EPDM
steel
PTFE
Base material: Brass
Port size (Common SUP type)
IN port
OUT port
3/8
Material
Seal
Body
Port size
—
Base material: Aluminum
Manifold
Model
Orifice size
2 mmø 3 mmø 4.5 mmø 6 mmø
1/8
1/4
Material
Base
Body
Aluminum Aluminum
Brass
Brass
Stainless Stainless
steel
steel
Base material: Stainless steel
Seal
NBR
FKM
EPDM
PTFE
applications— New
Pilot Operated 2 Port
VX Series variations
Pilot Operated 2 Port for
Zero Differential Pressure
Direct Operated 3 Port
VXD21/22/23
VXZ22/23
VX31/32/33
For Air, Water, Oil
For Air, Vacuum, Water, Oil
For Air, Vacuum, Water, Steam, Oil
Valve type
Port size
Orifice size
mmø
Valve type
Port size
Orifice size
mmø
Valve type
Port size
Orifice size
mmø
N.C./N.O.
1/4 to 1
32 A to 50 A
10 to 50
N.C./N.O.
1/4 to 1
10 to 25
N.C./N.O.
C.O.
1/8 to 3/8
1.5 to 4
Pilot Operated 2 Port
Water Hammer Relief,
Pilot Operated 2 Port
Pilot Operated 2 Port for
High Pressure
VXP21/22/23
VXR21/22/23
VXH22
For Steam (Air, Water, Oil)
For Water, Oil
For Air, Water, Oil
Valve type
Port size
Orifice size
mmø
Valve type
Port size
Orifice size
mmø
Valve type
Port size
Orifice size
mmø
N.C./N.O.
1/4 to 2
32 A to 50 A
10 to 50
N.C./N.O.
1/2 to 2
20 to 50
N.C.
1/4 to 1/2
10
2 Port for Dust Collector
(Solenoid type, Air Operated type)
Air Operated 2/3 Port
VXF21/22, VXFA21/22
VXA21/22, VXA31/32
For Air
For Air, Vacuum, Water, Oil
The VX series has
been renewed as
the new VX series,
with a new construction
Valve type
Port size
Orifice size
mmø
N.C.
3/4 to 11/2
20 to 40
Valve
Port
Orifice size
type
size
mmø
VXA21/22 N.C./N.O. 1/8 to 1/2 3 to 10
VXA31/32 C.O. 1/8 to 3/8 1.5 to 4
Model
Features 2
Solenoid Valves Flow Characteristics
(How to indicate flow characteristics)
1. Indication of flow characteristics
Indication of the flow characteristics in specifications for equipment such as solenoid valve, etc. is depending on “Table (1)”.
Table (1) Indication of Flow Characteristics
Corresponding
equipment
Indication by
Other
international standard indications
C, b
—
ISO 6358: 1989
JIS B 8390: 2000
—
S
JIS B 8390: 2000
Equipment: JIS B 8373, 8374, 8375, 8379, 8381
Equipment for
pneumatics
Equipment for
controlling
process fluids
Standards conforming to
Cv
ANSI/(NFPA)T3.21.3: 1990
Av
—
—
Cv
IEC60534-2-3: 1997
JIS B 2005: 1995
Equipment: JIS B 8471, 8472, 8473
2. Equipment for pneumatics
2.1 Indication according to the international standards
(1) Standards conforming to
ISO 6358: 1989
: Pneumatic fluid power—Components using compressible fluids—
Determination of flow-rate characteristics
JIS B 8390: 2000 : Pneumatic fluid power—Components using compressible fluids—
How to test flow-rate characteristics
(2) Definition of flow characteristics
Flow rate characteristics are indicated as a result of a comparison between sonic conductance C and critical pressure ratio b.
Sonic conductance C : Values which divide the passing mass flow rate of an equipment in a choked flow condition by the
product of the upstream absolute pressure and the density in the standard condition.
Critical pressure ratio b : It is the pressure ratio which will turn to the choke flow (downstream pressure/upstream pressure)
when it is smaller than this values. (critical pressure ratio)
Choked flow
: It is the flow in which the upstream pressure is higher than the downstream pressure and where
sonic speed in a certain part of an equipment is reached.
Gaseous mass flow rate is in proportion to the upstream pressure and not dependent on the
downstream pressure. (choked flow)
Subsonic flow
: Flow greater than the critical pressure ratio
Standard condition
: Air in a temperature state of 20°C, absolute pressure 0.1 MPa (= 100 kPa = 1 bar), relative humidity
65%.
It is stipulated by adding the abbreviation (ANR) after the unit depicting air volume.
(standard reference atmosphere)
Standard conforming to: ISO 8778: 1990 Pneumatic fluid power—Standard reference
atmosphere, JIS B 8393: 2000: Pneumatic fluid power—Standard reference atmosphere
(3) Formula of flow rate
It can be indicated by the practical unit as following.
When
P2 + 0.1
———— ≤ b, choked flow
P1 + 0.1
293
Q = 600 x C (P1 + 0.1) ———— ·····························································(1)
273 + t
When
P2 + 0.1
———— > b, subsonic flow
P1 + 0.1
Q = 600 x C (P1 + 0.1)
P2 + 0.1
———— – b
P1 + 0.1
1 – ——————
1–b
2
293
———— ···························· (2)
273 + t
Q : Air flow rate [dm3/min (ANR)], dm3 (Cubic decimeter) of SI unit are also allowed to
described by l (liter). 1 dm3 = 1 l .
Front matter 1
C
b
P1
P2
t
: Sonic conductance [dm3/(s·bar)]
: Critical pressure ratio [—]
: Upstream pressure [MPa]
: Downstream pressure [MPa]
: Temperature [°C]
Note) Formula of subsonic flow is the elliptic analogous curve.
Flow characteristics curve is indicated in the Graph (1) For details, please use SMC’s “Energy Saving Program”.
Example)
Obtain the air flow rate for P1 = 0.4 [MPa], P 2 = 0.3 [MPa], t = 20 [°C] when a solenoid valve is performed in
C = 2 [dm3/(s·bar)] and b = 0.3.
According to formula 1, the maximum flow rate = 600 x 2 x (0.4 + 0.1) x
293
————— = 600 [dm3/min (ANR)]
273 + 20
Flow rate ratio
0.3 + 0.1
Pressure ratio = ————— = 0.8
0.4 + 0.1
Based on the Graph (1), it is going to be 0.7 if it is read by the pressure ratio as 0.8 and the flow ratio to be b = 0.3.
Hence, flow rate = Max. flow x flow ratio = 600 x 0.7 = 420 [dm3/min (ANR)]
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0
0.5
b = 0.1
0.6
0.2
0.3
0.4
P1
Equipment
C, b
P2
Q
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
Pressure ratio (P2 + 0.1) / (P1 + 0.1)
Graph (1) Flow characteristics line
(4) Test method
Pipe the test equipment to the test circuit shown in Fig. (1). Keep the upstream pressure at a certain constant level above
0.3MPa. First measure the maximum flow rate in saturation. Then, measure the flow rate, upstream pressure and downstream
pressure each at 80%, 60%, 40% and 20% points of the flow rate. Calculate the sonic conductance C from the maximum flow
rate. Also, substitute other data for variables in the formula for subsonic flow and obtain the critical pressure rate b by averaging
the critical pressure rates at those points.
Pressure gauge or
pressure convertor
Air supply
Filter
ød3 ≥ 3d1
Shut off
valve
Differential pressure gauge or
differential pressure converter
3d3
ød2
Pressure control
equipment
ød1
Thermometer
Flow control valve
Flow meter
≥ 10d3
Pipe for measuring
temperature
10d1
3d1 10d2
3d2
Equipment
for test
Pipe for measuring
pressure in the
upstream side
Pipe for measuring
pressure in the
downstream side
Fig. (1) Test circuit based on ISO 6358, JIS B 8390
Front matter 2
Solenoid Valves Flow Characteristics
(How to indicate flow characteristics)
2.2 Effective area S
(1) Standards conforming to
JIS B 8390: 2000: Pneumatic fluid power—Components using compressible fluids—
Determination of flow rate characteristics
Equipment standards: JIS B 8373: 2 port solenoid valve for pneumatics
JIS B 8374: 3 port solenoid valve for pneumatics
JIS B 8375: 4 port, 5 port solenoid valve for pneumatics
JIS B 8379: Silencer for pneumatics
JIS B 8381: Fittings of flexible joint for pneumatics
(2) Definition of flow characteristics
Effective area S: is the cross-sectional area having an ideal throttle without friction deduced from the calculation of the pressure
changes inside an air tank or without reduced flow when discharging the compressed air in a choked flow, from
an equipment attached to the air tank. This is the same concept representing the “easy to run through” as sonic
conductance C (effective area).
(3) Formula of flow rate
When
P2 + 0.1
———— ≤ 0.5, choked flow
P1 + 0.1
293
Q = 120 x S (P1 + 0.1) ————··································································(3)
273 + t
When
P2 + 0.1 > 0.5, subsonic flow
————
P1 + 0.1
Q = 240 x S
(P2 + 0.1) (P1 – P2)
293
————··············································(4)
273 + t
Timer (Clock)
Pressure recorder
Fig. (2) Test circuit based on JIS B 8390
Front matter 3
Rectifier tube in the
downstream side
or
pressure convertor
Rectifier tube in the
upstream side
Conversion with sonic conductance C:
S = 5.0 x C ·······································································································(5)
Q :Air flow rate[dm3/min(ANR)], dm3 (cubic decimeter) of SI unit is good to be described by l (liter), too. 1 dm3 = 1 l
S : Effective area [mm2]
P1 : Upstream pressure [MPa]
P2 : Downstream pressure [MPa]
t : Temperature [°C]
Note) Formula for subsonic flow (4) is only applicable when the critical pressure ratio b is the unknown equipment. In the formula
by sonic conductance C (2), it is the same formula when b = 0.5.
(4) Test method
Pipe the test equipment to the test circuit shown in Fig. (2). Fill the air tank with compressed air and keep the pressure at a
constant level above 0.6MPa (0.5 MPa). Then discharge the air until the pressure in the tank drops to 0.25MPa (0.2 MPa).
Measure the time required to discharge the air and the residual pressure in the air tank after leaving it until the pressure
becomes stable in order to calculate the effective sectional area S by the following formula. Select the capacity of the air tank
according to the effective sectional area of the test equipment. In the case of JIS B 8373, 8374, 8375, 8379, 8381, the pressure
values are in parentheses and the coefficient of formula is 12.9.
V
Ps + 0.1
293
S = 12.1 — log10 (—————) —— ·················(6)
t
P + 0.1
T
Power
S : Effective area [mm2]
supply
Pressure switch
V : Air tank capacity [dm3]
Thermometer
t : Discharging time [s]
Control
Solenoid
Pressure control
Ps : Pressure inside air tank
circuit
valve
equipment
before discharging [MPa]
Equipment for test
P : Residual pressure inside air tank
after discharging [MPa]
T : Temperature inside air tank
Air supply Filter
Shut off
valve
before discharging [K]
Pressure gauge
2.3 Flow coefficient Cv factor
The United States Standard ANSI/(NFPA)T3.21.3:1990: Pneumatic fluid power—Flow rating test procedure
and reporting method for fixed orifice components
defines the Cv factor of flow coefficient by the following formula which is based on the test conducted by the test circuit
analogous to ISO 6358.
Q
Cv = ——————————— ·········································································(7)
∆P (P2 + Pa)
114.5 ——————
T1
∆P : Pressure drop between the static pressure tapping ports [bar]
P1 : Pressure of the upstream tapping port [bar gauge]
P2 : Pressure of the downstream tapping port [bar gauge]:P2 = P1 – ∆P
Q : Flow rate [dm3/s standard condition]
Pa : Atmospheric pressure [bar absolute]
T1 : Test conditions of the upstream absolute temperature [K]
is < P1 + Pa = 6.5 ± 0.2 bar absolute, T1 = 297 ± 5K, 0.07 bar ≤ ∆P ≤ 0.14 bar.
This is the same concept as effective area A which ISO6358 stipulates as being applicable only when the pressure drop is
smaller than the upstream pressure and the compression of air does not become a problem.
3. Equipment for process fluids
(1) Standards conforming to
IEC60534-2-3: 1997: Industrial process control valves. Part 2: Flow capacity, Section Three-Test
procedures
JIS B 2005: 1995: Test method for the flow coefficient of a valve
Equipment standards: JIS B 8471: Regulator for water
JIS B 8472: Solenoid valve for steam
JIS B 8473: Solenoid valve for fuel oil
(2) Definition of flow characteristics
Av factor: Value of the clean water flow rate represented by m3/s which runs through a valve (equipment for test) when the
pressure difference is 1 Pa. It is calculated using the following formula.
ρ
Av = Q ————·····································································································(8)
∆P
Av : Flow coefficient [m2]
Q : Flow rate [m3/s]
∆P : Pressure difference [Pa]
ρ
: Density of fluid [kg/m3]
(3) Formula of flow rate
It is described by the known unit. Also, the flow characteristics line shown in the Graph (2).
In the case of liquid:
∆P
Q = 1.9 x 106Av ————·······················································································(9)
G
Q : Flow rate [l/min]
Av : Flow coefficient [m2]
∆P : Pressure difference [MPa]
G : Relative density [water = 1]
In the case of saturated aqueous vapor:
Q = 8.3 x 106Av ∆P(P2 + 0.1) ··············································································(10)
Q : Flow rate [kg/h]
Av : Flow coefficient [m2]
∆P : Pressure difference [MPa]
P1 : Upstream pressure [MPa]: ∆P = P1 – P2
P2 : Downstream pressure [MPa]
Front matter 4
Solenoid Valves Flow Characteristics
(How to indicate flow characteristics)
3
2
Upstream pressure
2
P1 = 1MPa
P1 = 0.8MPa
1
0.9
0.8
0.7
0.6
0.5
Ex. 2
P1 = 0.6MPa
P1 = 0.5MPa
P1 = 0.4MPa
0.4
P1 = 0.3MPa
0.3
Ex. 1
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
P1 = 0.2MPa
0.2
0.2
P1 = 0.1MPa
0.1
0.001
0.002 0.003 0.004
0.01
0.02 0.03 0.04
l
3
Water flow rate Q0 [ /min] (When Av = 1 x 10–6 [m2])
Saturated aqueous vapor flow rate Q0 [kg/h] (when Av = 1 x 10–6 [m2])
Conversion of flow coefficient:
Av = 28 x 10–6 Kv = 24 x 10–6Cv ···········································································(11)
Here,
Kv factor: Value of the clean water flow rate represented by the m3/h which runs through the valve at 5 to 40°C, when the
pressure difference is 1 bar.
Cv factor (Reference values): It is the figures representing the flow rate of clean water by US gal/min which runs through the
valve at 60°F, when the pressure difference is 1 lbf/in2 (psi).
Values of pneumatic Kv are different from Cv because the testing method is different from each other.
0.1
0.1
Pressure difference ∆P [MPa]
Graph (2) Flow characteristics line
Example 1)
Obtain the pressure difference when water 15 [l/min] runs through the solenoid valve with an Av = 45 x 10–6 [m2].
Since Q0 = 15/45 = 0.33 [l/min], according to the Graph (2), if reading ∆P when Q0 is 0.33, it will be 0.031 [MPa].
Example 2)
Obtain the flow rate of saturated aqueous vapor when P1 = 0.8 [MPa], ∆P = 0.008 [MPa] with a solenoid valve with an Av =1.5 x
10–6 [m2].
According to the Graph (2), if reading Q0 when P1 is 0.8 and ∆P is 0.008, it is 0.7 [kg/h]. Hence, the flow rate Q = 0.7 x 1.5 = 1.05
[kg/h].
Front matter 5
(4) Test method
By attaching the equipment for testing with the test circuit shown in Fig. (3) and running water at 5 to 40°C, measure the flow rate
with a pressure difference of 0.075 MPa. However, the pressure difference needs to be set with a large enough difference so that
the Reynolds number does not go below a range of 4 x 104.
By substituting the measurement results for formula (8) to figure out Av.
Test range
Thermometer
Pressure tap
Throttle valve in
the upstream side
Equipment for test
Pressure tap
Flow meter
2d
≥ 20d
6d
Throttle valve in the
downstream side
≥ 10d
Fig. (3) Test circuit based on IEC60534-2-3, JIS B 2005
Front matter 6
Flow Characteristics
Note) Use this graph as a guide. In the case of obtaining an accurate flow rate, refer to
front matter pages 1 to 6.
Downstream pressure of valve (P2) MPa
For Air
Upst
1.0
ream
pres
sure
0.8
of va
lve P
1
≈ 1.0
MPa
Subsonic
cal
Criti sure
s
e
r
p
Sonic
0.9
0.6
0.8
0.7
0.4
0.6
0.5
0.4
0.2
0.3
0.2
0.1
0
VX211
VX22
VX23
VX2 32 4
VX2 32 5
VX2 3260-02
VX2 3260-03
04
50
100
150
200
250
300
100
200
300
400
500
600
200
400
600
500
800
1,000
350
ø2
ø3
1,000
ø4.5
1,200
ø6
1,250
ø8
500 700 900
ø10
500 700 900
ø10
700 1,000
Flow rate Q l/min (ANR)
How to read the graph
The sonic range pressure to generate a flow rate of 500 l/min (ANR) is
3
P1 ≈ 0.14 MPa for a ø6 orifice (VX2 —
2 4), and
P1 ≈ 0.3 MPa for a ø4.5 orifice (VX23).
For Saturated Steam
Downstream pressure of valve (P2) MPa
1.0
0.9
0.8
[663] (179)
Upst
ream
[664] (183)
pres
sure
0.7
[661] (170)
0.6
[660] (164)
0.5
[658] (158)
0.4
[656] (151)
0.3
[654] (143)
0.2
[650] (133)
0.1
[646] (120)
lve P
1
0.9
≈ 1.0
MPa
0.85
0.8
0.75
Subsonic
cal
Criti sure
s
e
r
p
0.7
0.65
0.6
0.55
Sonic
0.5
0.45
0.4
0.3
0.05
VX2112
VX22 2
VX23 2
VX2 32 4 2
VX2 32 50
VX2 32 60-02
VX2 32 60- 03
04
of va
0.95
[662] (174)
0.1
0.15
0.2
0.35
0.25
5
5
10
15
15
20
30
25
10
10
30
25
40
60
ø3
30
50
60
ø4.5
ø6
ø8
35
20
ø2
15
20
ø10
40
ø10
35
Flow rate Q kg/h
Figures inside [ ] indicate the saturated steam holding heat (kcal/kg). Figures inside ( ) indicate the saturation temperature (°C).
How to read the graph
The sonic range pressure to generate a flow rate of 15 kg/h is
P1 ≈ 0.15 MPa for ø4.5 orifice (VX23S), P1 ≈ 0.37 MPa for ø3 orifice (VX22S), and
P1 ≈ 0.82 MPa for ø2 orifice (VX211S). The holding heat differs somewhat depending on the pressure P1, but at 15 kg/h it is approximately 9700 kcal/h.
Front matter 7
Flow Characteristics
Note) Use this graph as a guide. In the case of obtaining an accurate flow rate, refer to
front matter pages 1 to 6.
For Water
30
20
Flow rate Q l/min
10
0
2 ø1
60-0
VX2
3
2
04
VX2
10
ø
3 60- 03
2
6
3 4 ø
2
VX2
5
4
3
8
50 ø
VX2
3
2
ø4.5
3 ø3
VX2
2 2
X
V
1 ø
1
VX2
2
2
1
0.1
0.001 (0.0018)
(0.0054)
0.01
(0.017)
0.05 (0.07)
Pressure differential P = (P1 – P2) MPa
How to read the graph
When a water flow of 2 l/min is generated, lP ≈ 0.017 MPa for a valve with ø3 orifice (VX212, 222, 232).
Front matter 8
Applicable Fluid Check List
Direct Operated 2 Port Solenoid Valve Series VX21/22/23
All Options (Single Unit)
Option symbol
Seal material
Nil
A
B
C
D
E
G
H
J
K
L Note 1)
M Note 1)
N
P
Q
S
V Note 1)
NBR
FKM
EPDM
PTFE
FKM
EPDM
NBR
FKM
EPDM
PTFE
FKM
FKM
FKM
EPDM
PTFE
PTFE
FKM
Body, Shading coil
material
Coil insulation type
B
Brass/Copper
H
Stainless steel/Silver
H
Steam (Max. 183°C)
Brass/Copper
Option symbol and body material
Brass
B
–
A
A
S
E
V
A
V
V
E
Stainless steel
J
J
H
H
Q
P
M
H
M
M
P
Note 1) The leakage amount (10–6 Pa·m3/s) of “V”, “M” options are values when differential
pressure is 0.1 MPa.
Note 2) If using for other fluids, contact SMC.
Front matter 9
High corrosive spec., Oil-free
Non-leak, Oil-free
—
Fluid Name and Option
Ethyl alcohol
Caustic soda (25% ≥)
Gas oil
Silicon oil
Steam system (Steam) (Max. 183°C)
Steam system (Condensation) (Max. 99°C)
Medium vacuum (up to 0.1 Pa.abs)
Perchloroethylene
Helium
Non-leak (10–6Pa·m3/s)
Heated water (Max. 99°C)
—
B
Note 1) “L”, “M”, “V” options are for non-lube treatment.
Note 2) Contact SMC regarding manifold type.
Fluid (Application)
Note
B
Non-leak, Oil-free
Glossary of Terms
Pressure Terminology
1. Maximum operating pressure differential
The maximum pressure differential (the difference between
the inlet and outlet pressure) which is allowed for operation,
with the valve closed or open. When the downstream pressure is 0 MPa, this becomes the maximum operating pressure.
2. Minimum operating pressure differential
The minimum pressure differential (differential between the
inlet pressure and the outlet pressure) required to keep the
main valve fully opened.
3. Maximum system pressure
The maximum pressure that can be applied inside the pipelines (line pressure).
(The pressure differential of the solenoid valve unit must be
less than the maximum operating pressure differential.)
4. Proof pressure
Others
1. Material
NBR: Nitrile rubber
FKM: Fluoro rubber – Trade names: Viton®, Dai-el®, etc.
EPDM: Ethylene propylene rubber
PTFE: Polytetrafluoroethylene resin – Trade names: Teflon®,
Polyflon®, etc.
2. Oil-free treatment
The degreasing and washing of wetted parts.
3. Passage symbol
In the JIS symbol (
) IN and OUT are in a blocked condition ( ), but actually in the case of reverse pressure
(OUT>IN), there is a limit to the blocking.
(
) is used to indicate that blocking of reverse pressure
is not possible.
The pressure which must be withstood without a drop in
performance after returning to the operating pressure range.
(value under the prescribed conditions)
Electrical Terminology
1. Apparent power (VA)
Volt-ampere is the product of voltage (V) and current (A). Power dissipation (W): For AC , W = V/A cosθ. For DC, W = V/A.
(Note) cosθ shows power factor. cosθ = 0.6
2. Surge voltage
A high voltage which is momentarily generated in the shut-off
unit by shutting off the power.
3. Degree of protection
A degree defined in the “JIS C 0920: Waterproof test of electric machinery/appliance and the degree of protection against
the intrusion of solid foreign objects”.
IP65: Dusttight, Low jetproof type
“Low jetproof type” means that no water intrudes inside an
equipment that could hinder from operating normally by
means of discharging water for 3 minutes in the prescribed
manner. Take appropriate protection measures, since a device is not usable in an environment where a water drop is
splashed.
Front matter 10
Direct Operated 2 Port Solenoid Valve
Series VX21/22/23
For Water, Oil, Steam, Air
Single Unit
Valve
Normally Closed (N.C.)
Normally closed (N.C.)
Normally open (N.O.)
Solenoid Coil
Coil: Class B, Class H
Rated Voltage
100 VAC, 200 VAC, 110 VAC,
220 VAC, 240 VAC, 230 VAC,
48 VAC, 24 VDC, 12 VDC
1 4, 3 8
12
1 4, 3 8
12
Normally Open (N.O.)
Material
Model VX21 VX22 VX23
—
—
2 mmø 3 mmø 4.5 mmø 6 mmø —
Port size 1 8 , 1 4 1 4 , 3 8 1 4 , 3 8
Brass, Stainless steel
NBR, FKM, EPDM, PTFE
Orifice size
Body
Seal
VX23
—
—
—
—
—
—
VX22
—
—
—
—
—
—
Orifice size
Model VX21
2 mmø 3 mmø 4.5 mmø 6 mmø —
8 mmø —
10 mmø —
Port size 1 8 , 1 4
Electrical Entry
• Grommet
• Conduit
• DIN terminal
• Conduit terminal
Manifold
Base
Common SUP type, Individual SUP
type (Base material Aluminum only)
Solenoid Coil
Coil: Class B, Class H
Rated Voltage
100 VAC, 200 VAC, 110 VAC,
220 VAC, 240 VAC, 230 VAC,
48 VAC, 24 VDC, 12 VDC
1
Electrical Entry
• Grommet
• Conduit
• DIN terminal
• Conduit terminal
Manifold
Model VX21 VX22 VX23
—
—
2 mmø 3 mmø 4.5 mmø 6 mmø —
IN port
Normally closed (N.C.)
Normally open (N.O.)
Aluminum, Brass, Stainless steel
Aluminum, Brass, Stainless steel
NBR, FKM, EPDM, PTFE
38
OUT port
Valve
Body
Base
Seal
(Common SUP type) Orifice size
Port size
Material
1 8, 1 4
Direct Operated 2 Port Solenoid Valve
Series VX21/22/23
For Water, Oil, Steam, Air
Standard Specifications
Valve
specifications
Valve construction
Withstand pressure
Body material
Seal material
Enclosure
Environment
AC
DC
Rated voltage
Coil
specifications
Direct operated poppet
5.0
Brass, Stainless steel
NBR, FKM, EPDM, PTFE
Dusttight, Low jetproof (equivalent to IP65)∗
Location without corrosive or explosive gases
100 VAC, 200 VAC, 110 VAC, 220 VAC, 230 VAC, 240 VAC, 48 VAC
24 VDC, 12 VDC
±10% of rated voltage
±20% or less of rated voltage
±2% or less of rated voltage
Class B, Class H
MPa
Allowable voltage fluctuation
AC
DC
Allowable leakage voltage
Coil insulation type
∗ Electrical entry, Grommet with surge voltage suppressor (GS) has a rating of IP40.
Solenoid Coil Specifications
Normally Open (N.O.)
DC Specification
Normally Closed (N.C.)
DC Specification
Power consumption (W) Temperature rise (C°) Note)
4.5
45
7
45
10.5
60
Model
VX21
VX22
VX23
AC Specification
Model
VX21
VX22
VX23
Frequency (Hz)
50
60
50
60
50
60
Temperature
rise (C°) Note)
45
40
55
50
65
60
How to order solenoid coil assembly
VX02 1 N
1 G
surge voltage suppressor
TL - With conduit terminal
and light
TZ - With conduit
terminal, surge
voltage suppressor
and light
VX23
Temperature
rise (C°) Note)
50
45
55
50
65
60
Note) The values are for an ambient temperature of 20°C and at the of rated voltage.
Name plate part no.
Clip
Enter by referring to “How to
Order (Single Unit)”.
Name plate
Solenoid coil
Coil insulation
type Note 1)
Nil
H∗
Class B
Class H
Clip part no. (For N.C.)
For VX21: VX021N-10
For VX22: VX022N-10
For VX23: VX023N-10
∗ DIN terminal or DC not
available.
Electrical entry
C- Conduit
voltage suppressor
T - With conduit terminal
TS - With conduit terminal and
VX22
Apparent power (VA)
Inrush
Holding
22
11
18
8
46
20
38
18
64
32
54
27
Symbol Valve
Nil
N.C.
2
N.O.
Note 1) Refer to the table (1) for the
available combinations.
G - Grommet
GS- With grommet surge
VX21
Valve/Material
VX21
VX22
VX23
100 VAC 50/60 Hz
200 VAC 50/60 Hz
110 VAC 50/60 Hz
220 VAC 50/60 Hz
24 VDC
12 VDC
240 VAC 50/60 Hz
48 VAC 50/60 Hz
230 VAC 50/60 Hz
Frequency (Hz)
50
60
50
60
50
60
AZ-T-VX Valve model
Rated voltage Note 1)
1
2
3
4
5
6
7
8
J
Model
Series
1
2
3
VX21
VX22
VX23
AC Specification
Apparent power (VA)
Inrush
Holding
19
9
16
7
43
19
35
16
62
30
52
25
Note) The values are for an ambient temperature of 20°C and at the rated voltage.
Power consumption (W) Temperature rise (C°) Note)
4.5
45
7
45
10.5
60
Model
Table (1) Rated Voltage – Electrical Option
Rated voltage
Class B
S
surge
AC/ Voltage Voltage With
voltage
DC symbol
suppressor
D - DIN
Connector
DS - DIN with surge voltage
suppressor
DL - DIN with light
DZ - DIN with surge
AC
voltage suppressor
suppressor and light
DO - For DIN (without connector)
∗ DIN type is available with class B insulation only.
∗ Refer to the table (1) for the available combinations between
each electrical option (S, L, Z) and rated voltage.
DC
1
2
3
4
7
8
J
5
6
100 V
200 V
110 V
220 V
240 V
48 V
230 V
24 V
12 V
L
With
light
Class H
Z
S
With light
and surge With surge
voltage
voltage
suppressor suppressor
—
—
—
—
—
—
—
—
L
Z
With
light
With light
and surge
voltage
suppressor
—
—
—
—
—
—
DC spec. is not
available.
2
Series VX21/22/23
For Water /Single Unit
Model/Valve Specifications
N.C.
N.O.
Passage symbol
Passage symbol
2
2
1
1
Normally Closed (N.C.)
Orifice
Port
size
size
(mmø)
Model
VX2110-01
VX2120-01
(6A)
VX2130-01
VX2110-02
VX2120-02
3 VX2220-02
VX2320-02
VX2130-02
4.5 VX2230-02
14
VX2330-02
(8A)
VX2240-02
6
VX2340-02
VX2250-02
8
VX2350-02
VX2260-02
10
VX2360-02
VX2220-03
3
VX2320-03
VX2230-03
4.5
VX2330-03
38
VX2240-03
6
(10A)
VX2340-03
VX2250-03
8
VX2350-03
VX2260-03
10
VX2360-03
12
VX2260-04
10
(15A)
VX2360-04
18
2
3
4.5
2
Normally Open (N.O.)
Max. operating
pressure
differential (MPa)
AC
2.0
0.9
0.4
2.0
0.9
1.7
2.5
0.4
0.6
0.85
0.35
0.55
0.13
0.17
0.08
0.1
1.7
2.5
0.6
0.85
0.35
0.55
0.13
0.17
0.08
0.1
0.08
0.1
DC
1.5
0.5
0.2
1.5
0.5
1.5
3.0
0.2
0.35
0.9
0.15
0.3
0.08
0.2
0.03
0.07
1.5
3.0
0.35
0.9
0.15
0.3
0.08
0.2
0.03
0.07
0.03
0.07
Note)
Flow
Max. system
characteristics
pressure Weight
(g)
Av x 10-6 m2 Cv converted (MPa)
4.1
0.17
7.9
0.33
15.0
0.61
300
4.1
0.17
7.9
0.33
15.0
0.61
26.0
1.10
38.0
1.60
3.0
1.0
46.0
1.90
7.9
0.33
15.0
0.61
26.0
1.10
38.0
1.60
53.0
2.20
53.0
2.20
3.0
1.0
470
620
300
470
620
470
620
560
700
560
700
470
620
470
620
470
620
560
700
560
700
560
700
Port
size
18
(6A)
Orifice
size
(mmø)
2
3
4.5
2
3
14
(8A)
4.5
6
3
38
(10)
4.5
6
Model
VX2112-01
VX2122-01
VX2132-01
VX2112-02
VX2122-02
VX2222-02
VX2322-02
VX2132-02
VX2232-02
VX2332-02
VX2242-02
VX2342-02
VX2222-03
VX2322-03
VX2232-03
VX2332-03
VX2242-03
VX2342-03
Max. operating
pressure
differential
(MPa)
Note)
Flow
Max. system
characteristics
pressure Weight
(g)
AC • DC Av x 10-6 m2 Cv converted (MPa)
0.9
4.1
0.17
0.45
0.33
7.9
320
0.2
15.0
0.61
0.9
0.17
4.1
0.45
500
0.8
7.9
0.33
660
1.2
320
0.2
500
0.3
15.0
0.61
3.0
660
0.6
500
0.15
26.0
1.10
660
0.35
500
0.8
7.9
0.33
660
1.2
500
0.3
15.0
0.61
660
0.6
500
0.15
1.10
26.0
660
0.35
Note) Weight of grommet type. Add 10 g for conduit type, 30 g for DIN
terminal type, and 60 g for conduit terminal type respectively.
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
Note) Weight of grommet type. Add 10 g for conduit type, 30 g for DIN
terminal type, and 60 g for conduit terminal type respectively.
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
Operating Fluid and Ambient Temperature
Power source
AC
DC
Operating fluid temperature (°C)
Solenoid valve option (symbol)
Nil, G, L
E, P
1 to 60
1 to 99
—
1 to 40
Note) With no freezing
3
Ambient
temperature
(°C)
–20 to 60
–20 to 40
Tightness of Valve (Leakage Rate)
Seal material
NBR, FKM, EPDM
Leakage rate (With water pressure)
0.1 cm3/min or less
Direct Operated 2 Port Solenoid Valve
Series VX21/22/23
For Water/Single Unit
How to Order (Single Unit)
Normally Open (N.O.)
01
01
1 G1
1 G1
For Water
VX 21 2 0
VX 21 2 2
Normally Closed (N.C.)
Model
Orifice size
Bracket
Refer to the table (1)
shown below for availability.
Nil
None
With bracket
B
Solenoid valve option
Refer to the table (2)
shown below for availability.
For Oil
Refer to the table (1)
shown below for availability.
∗ Refer to the table (4) if a
bracket is ordered
separately.
Port size
Refer to the table (1) shown below for availability.
—
Oil-free specification
Nil
Z
Select “Nil” because the solenoid valve
option “L” is the oil-free treatment.
1
2
3
4
5
G - Grommet
GS- With grommet surge
T - With conduit terminal
TS - With conduit terminal and
12 VDC
240 VAC 50/60 Hz
48 VAC 50/60 Hz
230 VAC 50/60 Hz
and light
TZ - With conduit
terminal, surge
voltage suppressor
and light
Refer to page 2 for ordering coil only.
Port no.
(Port size)
—
—
—
—
02 (1 4 ) 02 (1 4 )
03 (3 8 ) 03 (3 8 )
04 (1 2 ) 04 (1 2 )
—
—
—
Orifice symbol (diameter)
1
01 (1 8 )
02 (1 4 )
2
3
4
5
6
VX23 (2 mmø) (3 mmø) (4.5 mmø) (6 mmø) (8 mmø) (10 mmø)
—
—
—
—
—
—
—
—
—
—
—
—
—
Normally Open (N.O.)
Orifice symbol (diameter)
Solenoid valve (Port size)
Model
Port no.
(Port size)
VX21
VX22
VX23
01 ( 1 8)
02 ( 1 4)
—
—
02 ( 1 4 )
03 ( 3 8)
—
—
02 ( 1 4 )
03 ( 3 8 )
—
—
1
2
(2 mmø)
3
4
(3 mmø) (4.5 mmø) (6mmø)
—
—
—
—
Table (2) Solenoid Valve Option
Option
symbol
Nil
G
E
P
L
Seal material
NBR
EPDM
FKM
voltage suppressor
and light
DO - For DIN (without connector)
∗ DIN type is available with class B insulation only.
Table (3) Rated Voltage – Electrical Option
Solenoid valve (Port size)
VX22
suppressor
DL - DIN with light
DZ - DIN with surge
∗ Refer to the table (3) for the available combinations between each
electrical option (S, L, Z) and rated voltage.
Table (1) Port/Orifice Size
Normally Closed (N.C.)
VX21
D - DIN
Connector
DS - DIN with surge voltage
surge voltage suppressor
TL - With conduit terminal
∗ Refer to the table (3) shown below for availability.
Model
C- Conduit
voltage suppressor
Rated voltage
6
7
8
J
100 VAC 50/60 Hz
200 VAC 50/60 Hz
110 VAC 50/60 Hz
220 VAC 50/60 Hz
24 VDC
Electrical entry
Rc
NPTF
G
NPT
T
F
N
Body, Shading
coil material
Brass, Copper
Stainless steel, Silver
Brass, Copper
Stainless steel, Silver
Stainless steel, Silver
Coil
insulation type
Note
B
—
H
Heated water
(AC only)
B
High corrosive, Oil-free
Rated voltage
surge
AC/ Voltage Voltage With
voltage
DC symbol
suppressor
100 V
1
200 V
2
110 V
3
AC
220 V
4
240 V
7
48 V
8
230 V
J
24 V
5
DC
12 V
6
Rated voltage
L
Z
With
light
With light and
surge voltage
suppressor
—
—
—
—
—
—
—
—
Class H
S
L
Z
light and
surge
AC/ Voltage Voltage With
With With
surge voltage
voltage
DC symbol
light
suppressor
suppressor
100 V
1
200 V
2
110 V
3
AC
220 V
4
—
—
240 V
7
—
—
48 V
8
—
—
230 V
J
24 V
5
DC spec. is not
DC
available.
12 V
6
Table (4) Bracket Part No.
Model
1
VX21 2 0
Dimensions page 22 (Single unit)
Class B
S
3
2
Part no.
VX021N-12A
VX22 3 0
4
2
VX022N-12A
VX23 3 0
4
VX22 56 0
VX23 56 0
VX023N-12A-L
4
For Air
Nil
Suffix
For Steam
Thread type
Series VX21/22/23
For Water /Manifold
Solenoid Valve for Manifold/Valve Specifications
N.C.
N.O.
Passage symbol
2
Passage symbol
2
2
1
1
Common SUP type
Common SUP type
Normally Closed (N.C.)
Orifice
size
(mmø)
2
3
4.5
6
Model
VX2111
VX2121
VX2221
VX2321
VX2131
VX2231
VX2331
VX2241
VX2341
Normally Open (N.O.)
Max. operating
pressure
differential (MPa)
AC
2.0
0.9
1.7
2.5
0.4
0.6
0.85
0.35
0.55
DC
1.5
0.5
1.5
3.0
0.2
0.35
0.9
0.15
0.3
Flow
Max. system
characteristics
pressure
(MPa)
Av x 10-6 m2 Cv converted
0.17
2
7.9
0.33
3
3.0
15
0.61
4.5
26
1.10
6
Operating Fluid and Ambient Temperature
Power source
AC
DC
Operating fluid temperature (°C)
Solenoid valve option (symbol)
Nil, G, L
E, P
1 to 60
1 to 99
—
1 to 40
Note) With no freezing
Orifice
size
(mmø)
4.1
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
5
2
Ambient
temperature
(°C)
–20 to 60
–20 to 40
Model
Max. operating
pressure
differential (MPa)
VX2113
VX2123
VX2223
VX2323
VX2133
VX2233
VX2333
VX2243
VX2343
AC • DC
0.9
0.45
0.8
1.2
0.2
0.3
0.6
0.15
0.35
Flow
Max. system
characteristics
pressure
(MPa)
Av x 10-6 m2 Cv converted
4.1
0.17
7.9
0.33
3.0
15
0.61
26
1.10
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
Tightness of Valve (Leakage Rate)
Seal material
NBR, FKM, EPDM
Leakage rate (With water pressure)
0.1 cm3/min or less
Direct Operated 2 Port Solenoid Valve
Series VX21/22/23
For Water/Manifold
How to Order (Solenoid Valve for Manifold)
D - DIN
DS - DIN with surge
Refer to the table (1)
shown below for availability.
Solenoid valve option
T -With conduit terminal
voltage suppressor
TS -With conduit terminal and DL - DIN with light
surge voltage suppressor DZ - DIN with surge
TL - With conduit
voltage suppressor
Refer to the table (2)-1)
shown below for availability.
terminal and light
Rated voltage
1
2
3
4
5
Suffix
Z
—
Oil-free specification
Select “Nil” because the
solenoid valve option “L”
is the oil-free treatment.
6
7
8
J
100 VAC 50/60 Hz
200 VAC 50/60 Hz
110 VAC 50/60 Hz
220 VAC 50/60 Hz
24 VDC
TZ - With conduit
terminal, surge
voltage suppressor
and light
12 VDC
240 VAC 50/60 Hz
48 VAC 50/60 Hz
230 VAC 50/60 Hz
VVX21
VVX22 1
VVX23
∗ Refer to the table (3) for the available combinations
between each electrical option (S, L, Z) and rated voltage.
Table (1) Port/Orifice Size
C
07 1
Number of manifolds
Thread type
Nil
Port size
(Out port)
Rc
NPTF
G
NPT
T
F
N
Rc1/8
Rc1/4
02
2 stations
•
•
•
•
•
•
10
10 stations
Suffix
Nil
∗ All IN ports are Rc
3/8.
Z
—
Oil-free specification
Base, Seal material
Manifold base
Refer to the table (2)-(2).
•Blanking plate part no.
For VX21: VVX21-3A
For VX22: VVX22-3A
For VX23: VVX23-3A
Nil
F
E
NBR
FKM
EPDM
How to Order Manifold Assemblies (Example)
Enter the valve and blanking plate to be mounted under the
manifold base part number.
Example
VVX211C-05-1 ...... 1 set
∗ VX2111-1G1 ........ 4 sets
∗ VVX21-3A ........... 1 set
2
3
Solenoid
valve
VX21
VX22
VX23
Orifice symbol (diameter)
1
2
3
4
(2 mmø)
—
—
(3 mmø)
(4.5 mmø)
(6 mmø)
—
Table (2) Solenoid Valve Option
Solenoid valve Base, Seal material Body, Base
option symbol (1)
symbol (2)
material
Nil
G
E
P
L
C
S
CE
SE
SF
Seal
material
Coil
insulation
type
Note
NBR
B
—
EPDM
H
FKM
B
Brass
Stainless steel
Brass
Stainless steel
Stainless steel
Heated water
(AC only)
High corrosive, Oil-free
Table (3) Rated Voltage – Electrical Option
Seal material
1
connector)
∗ DIN type is available with
class B insulation only.
How to Order Manifold Bases
Station
and light
DO - For DIN (without
∗ Refer to the table (3) shown below for availability.
Refer to page 2 for ordering coil only.
1
2
For Water
Orifice size
Refer to the table (1)
shown below for availability.
Nil
voltage suppressor
“∗” is the symbol for mounting.
Add an “∗” in front of the part numbers
for solenoid valves, etc. to be mounted.
4
5
Rated voltage
Class B
S
With surge
AC/ Voltage
Voltage voltage
DC symbol
suppressor
100 V
1
200 V
2
110 V
3
AC
220 V
4
240 V
7
48 V
8
230 V
J
24 V
5
DC
12 V
6
L
Class H
Z
With
light
S
With light and With surge
surge voltage
voltage
suppressor suppressor
—
—
—
—
—
—
—
—
L
Z
With
light
With light and
surge voltage
suppressor
—
—
—
—
—
—
DC spec. is not
available.
n
Enter the product’s
part number in order,
counting the 1st station from the left in the
manifold arrangement,
when viewing the individual port in front.
For Oil
Model
Electrical entry
G - Grommet
C- Conduit
GS-With grommet surge
For Steam
Normally Open (N.O.)
1 G1
1 G1
Dimensions page 23 (manifold)
6
For Air
VX 21 2 1
VX 21 2 3
Normally Closed (N.C.)
Series VX21/22/23
For Oil /Single Unit
Model/Valve Specifications
N.C.
N.O.
Passage symbol
Passage symbol
2
2
1
1
Normally Closed (N.C.)
Orifice
Port
size
size
(mmø)
Model
VX2110-01
VX2120-01
(6A)
VX2130-01
VX2110-02
VX2120-02
3 VX2220-02
VX2320-02
VX2130-02
4.5 VX2230-02
14
VX2330-02
(8A)
VX2240-02
6
VX2340-02
VX2250-02
8
VX2350-02
VX2260-02
10
VX2360-02
VX2220-03
3
VX2320-03
VX2230-03
4.5
VX2330-03
38
VX2240-03
6
(10A)
VX2340-03
VX2250-03
8
VX2350-03
VX2260-03
10
VX2360-03
12
VX2260-04
10
(15A)
VX2360-04
18
2
3
4.5
2
Normally Open (N.O.)
Max. operating
pressure
differential (MPa)
AC
1.5
0.5
0.2
1.5
0.5
1.2
1.7
0.2
0.35
0.55
0.2
0.35
0.1
0.14
0.05
0.08
1.2
1.7
0.35
0.55
0.2
0.35
0.1
0.14
0.05
0.08
0.05
0.08
DC
1.5
0.5
0.15
1.5
0.5
1.2
2.0
0.15
0.3
0.85
0.1
0.3
0.08
0.2
0.03
0.07
1.2
2.0
0.3
0.85
0.1
0.3
0.08
0.2
0.03
0.07
0.03
0.07
Note)
Flow
Max. system
characteristics
pressure Weight
(g)
Av x 10-6 m2 Cv converted (MPa)
4.1
0.17
7.9
0.33
15
0.61
300
4.1
0.17
7.9
0.33
15
0.61
26
1.1
38
1.6
3.0
1.0
1.9
46
7.9
0.33
15
0.61
26
1.1
38
1.6
53
2.2
53
2.2
3.0
1.0
470
620
300
470
620
470
620
560
700
560
700
470
620
470
620
470
620
560
700
560
700
560
700
Port
size
18
(6A)
Orifice
size
(mmø)
2
3
4.5
2
3
14
(8A)
4.5
6
3
38
(10)
4.5
6
Model
VX2112-01
VX2122-01
VX2132-01
VX2112-02
VX2122-02
VX2222-02
VX2322-02
VX2132-02
VX2232-02
VX2332-02
VX2242-02
VX2342-02
VX2222-03
VX2322-03
VX2232-03
VX2332-03
VX2242-03
VX2342-03
Max, operating
pressure
differential
(MPa)
Note)
Flow
Max. system
characteristics
pressure Weight
(g)
AC • DC Av x 10-6 m2 Cv converted (MPa)
4.1
0.17
0.8
0.45
0.33
7.9
320
0.2
15
0.61
0.8
4.1
0.17
0.45
500
0.7
0.33
7.9
660
1.0
320
0.2
500
0.3
0.61
15
3.0
660
0.6
500
0.15
1.1
26
660
0.35
500
0.7
7.9
0.33
660
1.0
500
0.3
15
0.61
660
0.6
500
0.15
1.1
26
660
0.35
Note) Weight of grommet type. Add 10 g for conduit type, 30 g for DIN
terminal type, and 60 g for conduit terminal type respectively.
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
Note) Weight of grommet type. Add 10 g for conduit type, 30 g for DIN
terminal type, and 60 g for conduit terminal type respectively.
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
Operating Fluid and Ambient Temperature
Power source
AC
DC
Operating fluid temperature (°C)
Solenoid valve option (symbol)
A, H
D, N
Ambient
temperature
(°C)
–5 Note) to 60
–5 Note) to 40
–5 Note) to 120
—
–20 to 60
–20 to 40
Note) Kinematic viscosity: 50 mm2/s or less
7
Tightness of Valve (Leakage Rate)
Seal material
FKM
Leakage rate (With oil pressure)
0.1 cm3/min or less
Direct Operated 2 Port Solenoid Valve
Series VX21/22/23
For Oil/Single Unit
Normally Open (N.O.)
01
01
1 G1
1 G1
For Water
VX 21 2 0
VX 21 2 2
Normally Closed (N.C.)
Model
Orifice size
Bracket
Refer to the table (1)
shown below for availability.
Nil
None
With bracket
B
Solenoid valve option
Refer to the table (2)
shown below for availability.
For Oil
Refer to the table (1)
shown below for availability.
∗ Refer to the table (4) if a
bracket is ordered
separately.
Port size
Refer to the table (1) shown below for availability.
—
Oil-free specification
Nil
Z
Electrical entry
Rc
NPTF
G
NPT
T
F
N
G - Grommet
GS- With grommet surge
voltage suppressor
Rated voltage
1
2
3
4
5
6
7
8
J
100 VAC 50/60 Hz
200 VAC 50/60 Hz
110 VAC 50/60 Hz
220 VAC 50/60 Hz
24 VDC
T - With conduit terminal
TS - With conduit terminal and
12 VDC
240 VAC 50/60 Hz
48 VAC 50/60 Hz
230 VAC 50/60 Hz
and light
TZ - With conduit
terminal, surge
voltage suppressor
and light
Refer to page 2 for ordering coil only.
Port no.
(Port size)
01 (1 8 )
02 (1 4 )
—
—
—
—
02 (1 4 ) 02 (1 4 )
03 (3 8 ) 03 (3 8 )
04 (1 2 ) 04 (1 2 )
—
—
—
Orifice symbol (diameter)
1
2
3
4
5
6
VX23 (2 mmø) (3 mmø) (4.5 mmø) (6 mmø) (8 mmø) (10 mmø)
—
—
—
—
—
—
—
—
—
—
—
—
—
Normally Open (N.O.)
Orifice symbol (diameter)
Solenoid valve (Port size)
Model
Port no.
(Port size)
VX21
VX22
VX23
01 ( 1 8)
02 ( 1 4)
—
—
02 ( 1 4 )
03 ( 3 8)
—
—
02 ( 1 4 )
03 ( 3 8 )
—
—
1
(2 mmø)
2
Seal
material
A
H
D
N
FKM
Body, Shading
coil material
Brass, Copper
Stainless steel, Silver
Brass, Copper
Stainless steel, Silver
3
4
(3 mmø) (4.5 mmø) (6 mmø)
—
—
—
—
Table (2) Solenoid Valve Option
Option
symbol
voltage suppressor
and light
DO - For DIN (without connector)
∗ DIN type is available with class B insulation only.
Table (3) Rated Voltage – Electrical Option
Solenoid valve (Port size)
VX22
suppressor
DL - DIN with light
DZ - DIN with surge
∗ Refer to the table (3) for the available combinations between each
electrical option (S, L, Z) and rated voltage.
Table (1) Port/Orifice Size
Normally Closed (N.C.)
VX21
D - DIN
Connector
DS - DIN with surge voltage
surge voltage suppressor
TL - With conduit terminal
∗ Refer to the table (3) shown below for availability.
Model
C- Conduit
Coil
insulation type
B
H
The additives contained in oil are different depending on the type
and manufacturers, so the durability of the seal materials will
vary. For details, please consult with SMC.
Rated voltage
Class B
S
surge
AC/ Voltage Voltage With
voltage
DC symbol
suppressor
100 V
1
200 V
2
110 V
3
AC
220 V
4
240 V
7
48 V
8
230 V
J
24 V
5
DC
12 V
6
Rated voltage
L
Z
With
light
With light and
surge voltage
suppressor
—
—
—
—
—
—
—
—
Class H
S
L
Z
light and
surge
AC/ Voltage Voltage With
With With
surge voltage
voltage
DC symbol
light
suppressor
suppressor
100 V
1
200 V
2
110 V
3
AC
220 V
4
—
—
240 V
7
—
—
48 V
8
—
—
230 V
J
24 V
5
DC spec. is not
DC
available.
12 V
6
Table (4) Bracket Part No.
Model
1
VX21 2 0
3
2
Part no.
VX021N-12A
VX22 3 0
Dimensions page 22 (Single unit)
4
2
VX022N-12A
VX23 3 0
4
VX22 56 0
VX23 56 0
VX023N-12A-L
8
For Air
Nil
Suffix
For Steam
Thread type
Series VX21/22/23
For Oil /Manifold
Solenoid Valve for Manifold/Valve Specifications
N.C.
N.O.
Passage symbol
2
Passage symbol
2
2
1
1
Common SUP type
Common SUP type
Normally Closed (N.C.)
Orifice
size
(mmø)
2
3
4.5
6
Model
VX2111
VX2121
VX2221
VX2321
VX2131
VX2231
VX2331
VX2241
VX2341
Normally Open (N.O.)
Max. operating
pressure
differential (MPa)
AC
1.5
0.5
1.2
1.7
0.2
0.35
0.55
0.2
0.35
DC
1.5
0.5
1.2
2.0
0.15
0.3
0.85
0.1
0.3
Flow
Max. system
characteristics
pressure
(MPa)
Av x 10-6 m2 Cv converted
0.17
2
7.9
0.33
3
3.0
15
0.61
4.5
26
1.1
6
Operating Fluid and Ambient Temperature
Power source
AC
DC
Orifice
size
(mmø)
4.1
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
Operating fluid temperature (°C)
Solenoid valve option (symbol)
A, H
D, N
Ambient
temperature
(°C)
–5 Note) to 60
–5 Note) to 40
–5 Note) to 120
—
–20 to 60
–20 to 40
Note) Kinematic viscosity: 50 mm2/s or less
9
2
Model
Max. operating
pressure
differential (MPa)
VX2113
VX2123
VX2223
VX2323
VX2133
VX2233
VX2333
VX2243
VX2343
AC • DC
0.8
0.45
0.7
1.0
0.2
0.3
0.6
0.15
0.35
Flow
Max. system
characteristics
pressure
(MPa)
Av x 10-6 m2 Cv converted
4.1
0.17
7.9
0.33
3.0
15
0.61
26
1.1
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
Tightness of Valve (Leakage Rate)
Seal material
FKM
Leakage rate (With oil pressure)
0.1 cm3/min or less
Direct Operated 2 Port Solenoid Valve
Series VX21/22/23
For Oil/Manifold
How to Order (Solenoid Valve for Manifold)
D - DIN
DS - DIN with surge
Refer to the table (1)
shown below for availability.
Solenoid valve option
T -With conduit terminal
voltage suppressor
TS -With conduit terminal and DL - DIN with light
surge voltage suppressor DZ - DIN with surge
TL - With conduit
voltage suppressor
Refer to the table (2)-1)
shown below for availability.
terminal and light
Rated voltage
1
2
3
4
5
Suffix
Z
—
Oil-free specification
For Water
Orifice size
Refer to the table (1)
shown below for availability.
Nil
voltage suppressor
6
7
8
J
100 VAC 50/60 Hz
200 VAC 50/60 Hz
110 VAC 50/60 Hz
220 VAC 50/60 Hz
24 VDC
TZ - With conduit
terminal, surge
voltage suppressor
and light
12 VDC
240 VAC 50/60 Hz
48 VAC 50/60 Hz
230 VAC 50/60 Hz
and light
DO - For DIN (without
connector)
∗ Refer to the table (3) shown below for availability.
∗ DIN type is available with
class B insulation only.
Refer to page 2 for ordering coil only.
∗ Refer to the table (3) for the available combinations
between each electrical option (S, L, Z) and rated voltage.
How to Order Manifold Bases
VVX21
VVX22 1
VVX23
CF
Nil
Rc
NPTF
G
NPT
T
F
N
Rc1/8
Rc1/4
02
2 stations
•
•
•
•
•
•
10 10 stations
Thread type
∗ All IN ports are Rc
3/8.
Suffix
Nil
Z
—
Oil-free specification
Base, Seal material
Manifold base
ÁBlanking
07 1
Number of manifolds
Port size
(Out port)
1
2
Table (1) Port/Orifice Size
Solenoid
valve
Refer to the table (2)-(2).
Orifice symbol (diameter)
1
2
3
4
(2 mmø)
—
—
(3 mmø)
(4.5 mmø)
(6 mmø)
—
Table (2) Solenoid Valve Option
Solenoid valve
Base, Seal
Body, Base
option symbol (1) material symbol (2) material
A
H
D
N
CF
SF
CF
SF
Seal
material
Brass
Stainless steel
Brass
Stainless steel
Coil
insulation
type
Note
B
—
H
AC only
FKM
The additives contained in oil are different depending on the type and
manufacturers, so the durability of the seal materials will vary. For details,
please consult with SMC.
plate part no.
For VX21: VVX21-3A-F
For VX22: VVX22-3A-F
For VX23: VVX23-3A-F
Table (3) Rated Voltage – Electrical Entry – Electrical Option
Rated voltage
Seal material: FKM
How to Order Manifold Assemblies (Example)
Enter the valve and blanking plate to be mounted under the
manifold base part number.
Example
VVX211CF-05-1...... 1 set
∗ VX2111A-1G1........ 4 sets
∗ VVX21-3A-F.......... 1 set
Station
VX21
VX22
VX23
1
2
3
“∗” is the symbol for mounting.
Add an “∗” in front of the part numbers
for solenoid valves, etc. to be mounted.
4
5
n
Enter the product’s
part number in order,
counting the 1st station from the left in the
manifold arrangement,
when viewing the individual port in front.
Class B
S
With surge
AC/ Voltage
Voltage voltage
DC symbol
suppressor
100 V
1
200 V
2
110 V
3
AC
220 V
4
240 V
7
48 V
8
230 V
J
24 V
5
DC
12 V
6
L
Class H
Z
With
light
S
With light and With surge
surge voltage
voltage
suppressor suppressor
—
—
—
—
—
—
—
—
For Oil
Model
Electrical entry
G - Grommet
C- Conduit
GS-With grommet surge
For Steam
Normally Open (N.O.)
1 G1
1 G1
L
Z
With
light
With light and
surge voltage
suppressor
—
—
—
—
—
—
DC spec. is not
available.
Dimensions page 23 (manifold)
10
For Air
VX 21 2 1
VX 21 2 3
Normally Closed (N.C.)
Series VX21/22/23
For Steam /Single Unit
Model/Valve Specifications
N.C.
N.O.
Passage symbol
Passage symbol
2
2
1
1
Normally Closed (N.C.)
Orifice
Port
size
size
(mmø)
Model
VX2110-01
18
VX2120-01
(6A)
VX2130-01
VX2110-02
VX2120-02
VX2130-02
4.5 VX2230-02
14
VX2330-02
(8A)
VX2240-02
6
VX2340-02
VX2250-02
8
VX2350-02
VX2260-02
10
VX2360-02
3 VX2220-03
VX2230-03
4.5
VX2330-03
VX2240-03
38
6
VX2340-03
(10A)
VX2250-03
8
VX2350-03
VX2260-03
10
VX2360-03
12
VX2260-04
10
(15A)
VX2360-04
2
3
4.5
2
3
Normally Open (N.O.)
Max. operating
pressure
differential (MPa)
AC
1.0
1.0
0.45
1.0
1.0
0.45
0.75
1.0
0.4
0.5
0.15
0.2
0.08
0.1
1.0
0.75
1.0
0.4
0.5
0.15
0.2
0.08
0.1
0.08
0.1
Note)
Flow
Max. system
characteristics
pressure Weight
(g)
Av x 10-6 m2 Cv converted (MPa)
4.1
0.17
7.9
0.33
15
0.61
300
4.1
0.17
7.9
0.33
1.0
15
26
38
0.61
1.1
1.6
0.5
46
7.9
1.9
0.33
15
0.61
26
1.1
38
1.6
53
2.2
53
2.2
1.0
0.5
470
620
470
620
560
700
560
700
470
470
620
470
620
560
700
560
700
560
700
Port
size
18
(6A)
Orifice
size
(mmø)
2
3
4.5
2
3
14
(8A)
4.5
6
3
38
4.5
(10)
6
Model
VX2112-01
VX2122-01
VX2132-01
VX2112-02
VX2122-02
VX2222-02
VX2132-02
VX2232-02
VX2332-02
VX2242-02
VX2342-02
VX2222-03
VX2232-03
VX2332-03
VX2242-03
VX2342-03
Max, operating
pressure
differential
(MPa)
AC
1.0
0.7
0.3
1.0
0.7
1.0
0.3
0.45
0.8
0.25
0.45
1.0
0.45
0.8
0.25
0.45
Note)
Flow
Max. system
characteristics
pressure Weight
(g)
Av x 10-6 m2 Cv converted (MPa)
4.1
0.17
7.9
0.33
320
15
0.61
4.1
0.17
7.9
0.33
15
0.61
26
1.1
1.0
7.9
0.33
15
0.61
26
1.1
500
320
500
660
500
660
500
660
500
660
Note) Weight of grommet type. Add 60 g for conduit terminal type.
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
Note) Weight of grommet type. Add 60 g for conduit terminal type.
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
Operating Fluid and Ambient Temperature
Power source
AC
11
Operating fluid temperature (°C)
Solenoid valve option (symbol)
S, Q
Ambient
temperature
(°C)
183
–20 to 60
Tightness of Valve (Leakage Rate)
Seal material
PTFE
Leakage rate (With air pressure)
300 cm3/min or less
Direct Operated 2 Port Solenoid Valve
Series VX21/22/23
For Steam/Single Unit
How to Order (Single Unit)
1 G1
1 G1
Model
Orifice size
Refer to the table (1)
shown below for availability.
Bracket
Refer to the table (1)
shown below for availability.
Nil
None
With bracket
B
Solenoid valve option
Refer to the table (2)
shown below for availability.
∗ Refer to the table (4) if a
bracket is ordered
separately.
Port size
For Oil
Normally Open (N.O.)
01
01
For Water
VX 21 2 0
VX 21 2 2
Normally Closed (N.C.)
Nil
Suffix
—
Oil-free specification
Nil
Z
Electrical entry
Rc
NPTF
G
NPT
T
F
N
G - Grommet
GS- With grommet surge
C- Conduit
voltage suppressor
7
8
J
100 VAC 50/60 Hz
200 VAC 50/60 Hz
110 VAC 50/60 Hz
220 VAC 50/60 Hz
240 VAC 50/60 Hz
48 VAC 50/60 Hz
230 VAC 50/60 Hz
For Air
Rated voltage
1
2
3
4
T - With conduit terminal
TS - With conduit terminal and
surge voltage suppressor
TL - With conduit terminal
and light
∗ Refer to the table (3) shown below for availability.
TZ - With conduit
terminal, surge
voltage suppressor
and light
Refer to page 2 for ordering coil only.
∗ Refer to the table (3) for the available combinations between
each electrical option (S, L, Z) and rated voltage.
Table (1) Port/Orifice Size
Normally Closed (N.C.)
Table (3) Rated Voltage – Electrical Option
Solenoid valve (Port size)
Model
Port no.
(Port size)
Orifice symbol (diameter)
1
VX21
VX22
01 (1 8 )
02 (1 4 )
—
—
—
—
02 (1 4 ) 02 (1 4 )
03 (3 8 ) 03 (3 8 )
04 (1 2 ) 04 (1 2 )
—
—
—
2
3
4
5
6
VX23 (2 mmø) (3 mmø) (4.5 mmø) (6 mmø) (8 mmø) (10 mmø)
—
—
—
—
—
—
—
—
—
—
(VX22)
—
—
—
—
—
Normally Open (N.O.)
Orifice symbol (diameter)
Solenoid valve (Port size)
Model
Port no.
(Port size)
VX21
VX22
VX23
01 ( 1 8)
02 ( 1 4)
—
—
02 ( 1 4 )
03 ( 3 8)
—
—
02 ( 1 4 )
03 ( 3 8 )
—
—
1
2
(2 mmø)
3
4
(3 mmø) (4.5 mmø) (6 mmø)
—
—
—
—
Rated voltage
Seal material
S
Q
PTFE
Body material
Model
3
2
Brass
Stainless steel
Solenoid coil: AC, Class H only
Coil insulation
type
H
L
Z
Table (4) Bracket Part No.
1
Option
symbol
Class B
S
surge
light and
AC/ Voltage Voltage With
With With
surge voltage
voltage
DC symbol
light
suppressor
suppressor
100 V
1
200 V
2
110 V
3
AC
220 V
4
—
—
240 V
7
—
—
48 V
8
—
—
230 V
J
24 V
5
DC spec. is not
DC
available.
12 V
6
VX21 2 0
Table (2) Solenoid Valve Option
For Steam
Refer to the table (1) shown below for availability.
Thread type
Part no.
VX021N-12A
VX22 3 0
4
2
VX022N-12A
VX23 3 0
4
VX22 56 0
VX23 56 0
VX023N-12A-L
Dimensions page 22 (Single unit)
12
Series VX21/22/23
For Steam /Manifold
Solenoid Valve for Manifold/Valve Specifications
N.C.
N.O.
Passage symbol
2
Passage symbol
2
2
1
1
Common SUP type
Common SUP type
Normally Closed (N.C.)
Orifice
size
(mmø)
2
3
4.5
6
Model
VX2111
VX2121
VX2131
VX2231
VX2331
VX2241
VX2341
Normally Open (N.O.)
Max. operating
pressure
differential (MPa)
AC
1.0
1.0
0.45
0.75
1.0
0.4
0.5
Flow
Max. system
characteristics
pressure
(MPa)
Av x 10-6 m2 Cv converted
4.1
7.9
15
0.61
3
3.0
4.5
26
1.1
Operating Fluid and Ambient Temperature
Power source
AC
Orifice
size
(mmø)
2
0.17
0.33
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
13
2
Operating fluid temperature (°C)
Solenoid valve option (symbol)
S, Q
Ambient
temperature
(°C)
183
–20 to 60
6
Model
Max. operating
pressure
differential (MPa)
VX2113
VX2123
VX2223
VX2133
VX2233
VX2333
VX2243
VX2343
AC
1.0
0.7
1.0
0.3
0.45
0.8
0.25
0.45
Flow
Max. system
characteristics
pressure
(MPa)
Av x 10-6 m2 Cv converted
4.1
0.17
7.9
0.33
15
0.61
26
1.1
3.0
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
Tightness of Valve (Leakage Rate)
Seal material
PTFE
Leakage rate (With air pressure)
300 cm3/min or less
Series VX21/22/23
Direct Operated 2 Port Solenoid Valve
For Steam/Manifold
How to Order (Solenoid Valve for Manifold)
Normally Open (N.O.)
1 G1
1 G1
For Water
VX 21 2 1
VX 21 2 3
Normally Closed (N.C.)
Electrical entry
G - Grommet
C- Conduit
GS-With grommet surge
Orifice size
Refer to the table (1)
shown below for availability.
Refer to the table (1)
shown below for availability.
Solenoid valve option
voltage suppressor
For Oil
Model
Refer to the table (2)-(1)
shown below for availability.
Z
—
Oil-free specification
7
8
J
100 VAC 50/60 Hz
200 VAC 50/60 Hz
110 VAC 50/60 Hz
220 VAC 50/60 Hz
T - With conduit terminal
TS - With conduit terminal and
240 VAC 50/60 Hz
48 VAC 50/60 Hz
230 VAC 50/60 Hz
surge voltage suppressor
TL - With conduit
terminal and light
TZ - With conduit terminal,
∗ Refer to the table (3) shown below for availability.
surge voltage
suppressor and light
Refer to page 2 for ordering coil only.
For Air
Nil
1
2
3
4
For Steam
Rated voltage
Suffix
∗ Refer to the table (3) for the available combinations
between each electrical option (S, L, Z) and rated voltage.
Table (1) Port/Orifice Size
How to Order Manifold Bases
Solenoid
valve
VVX21
VVX22 1
VVX23
CP
07 1
Number of manifolds
Thread type
Port size
(Out port)
1
2
Nil
Rc
NPTF
G
NPT
T
F
N
Rc1/8
Rc1/4
02
2 stations
•
•
•
•
•
•
10 10 stations
Suffix
Nil
∗ All IN ports are Rc
3/8.
Z
—
Oil-free specification
Base, Seal material
Manifold base
Refer to the table (2)-(2).
•Blanking plate part no.
Seal material: PTFE
How to Order Manifold Assemblies (Example)
Enter the valve and blanking plate to be mounted under the
manifold base part number.
Example
VVX211CP-05-1......1 set
∗ VX2111S-1G1........ 4 sets
∗ VVX21-3A-P.......... 1 set
1
2
3
2
3
4
(2 mmø)
—
—
(3 mmø)
(N.C.)
—
(4.5 mmø)
(6 mmø)
—
Table (2) Solenoid Valve Option
Solenoid valve
Base, Seal
option symbol (1) material symbol (2)
S
Q
“∗” is the symbol for mounting.
Add an “∗” in front of the part numbers
for solenoid valves, etc. to be mounted.
4
5
CP
SP
Body, Base
material
Seal
material
Coil
insulation type
Brass
Stainless steel
PTFE
H
Table (3) Rated Voltage – Electrical Option
Rated voltage
For VX21: VVX21-3A-P
For VX22: VVX22-3A-P
For VX23: VVX23-3A-P
Station
VX21
VX22
VX23
Orifice symbol (diameter)
1
Class H
S
L
Z
light and
surge
AC/ Voltage Voltage With
With With
surge voltage
voltage
DC symbol
light
suppressor
suppressor
100 V
1
200 V
2
110 V
3
AC
220 V
4
—
—
240 V
7
—
—
48 V
8
—
—
230 V
J
24 V
5
DC spec. is not
DC
available.
12 V
6
Dimensions page 23 (manifold)
n
Enter the product’s
part number in order,
counting the 1st station from the left in the
manifold arrangement,
when viewing the individual port in front.
14
Series VX21/22/23
When the fluid is air.
For Air /Single Unit
Please select the VCA series when using air because
it is specifically designed for it. (The VCA series is
limited to air to improve its function and service life.)
(Inert gas, Non-leak, Medium vacuum)
Model/Valve Specifications
N.C.
N.O.
Passage symbol
Passage symbol
2
2
1
1
Normally Closed (N.C.)
Orifice
Port
size
size
(mmø)
Model
2
3
4.5
2
VX2110-01
18
VX2120-01
(6A)
VX2130-01
VX2110-02
VX2120-02
3 VX2220-02
VX2320-02
VX2130-02
4.5 VX2230-02
14
VX2330-02
(8A)
VX2240-02
6
VX2340-02
VX2250-02
8
VX2350-02
VX2260-02
10
VX2360-02
VX2220-03
3
VX2320-03
VX2230-03
4.5
VX2330-03
38
VX2240-03
6
(10A)
VX2340-03
VX2250-03
8
VX2350-03
VX2260-03
10
VX2360-03
12
VX2260-04
10
(15A)
VX2360-04
Normally Open (N.O.)
Max. operating
pressure
differential (MPa)
AC
2.0
1.1
0.45
2.0
1.1
2.0
3.0
0.45
0.75
1.0
0.4
0.5
0.15
0.2
0.08
0.1
2.0
3.0
0.75
1.0
0.4
0.5
0.15
0.2
0.08
0.1
0.08
0.1
Flow
Max. system
characteristics
pressure
(MPa)
DC C[dm3/(s·bar)]
b
Cv
0.59
0.48 0.18
1.5
1.2
0.45 0.33
0.6
2.4
0.44 0.61
0.2
0.59
0.48 0.18
1.5
0.6
0.45 0.33
1.2
1.5
3.0
3.0
0.2
0.46 0.61
2.3
0.35
0.9
0.15
0.3
1.1
4.1
0.35
0.08
0.3
1.6
6.4
0.2
1.0
0.03
0.3
2.0
8.8
0.07
1.5
0.45 0.33
1.2
3.0
0.35
0.46 0.61 3.0
2.3
0.9
0.15
0.3
1.1
4.1
0.35
0.08
0.3
1.6
6.4
0.2
0.03
1.0
0.3
2.2
11
0.07
0.03
0.3
2.2
11
0.07
Note)
Weight
(g)
Orifice
size
(mmø)
Port
size
18
300
470
620
300
470
620
470
620
560
700
560
700
470
620
470
620
470
620
560
700
560
700
560
700
(6A)
14
(8A)
38
(10)
Model
2
3
4.5
2
VX2112-01
VX2122-01
VX2132-01
VX2112-02
VX2122-02
3
VX2222-02
VX2322-02
VX2132-02
4.5 VX2232-02
VX2332-02
VX2242-02
6
VX2342-02
VX2222-03
3
VX2322-03
VX2232-03
4.5
VX2332-03
VX2242-03
6
VX2342-03
Max.
operating
pressure
differential
(MPa)
1.5
0.7
0.3
1.5
0.7
1.0
1.6
0.3
0.45
0.8
0.25
0.45
1.0
1.6
0.45
0.8
0.25
0.45
Flow
characteristics
b
Cv
C[dm3/(s·bar)]
0.18
0.59
0.48
0.33
1.2
0.45
2.3
0.46
0.61
0.59
0.48
0.18
1.2
0.45
0.33
2.3
0.46
0.61
4.1
0.3
1.1
1.2
0.45
0.33
2.3
0.46
0.61
4.1
0.3
1.1
Note)
Max. system
pressure Weight
(g)
(MPa)
320
3.0
500
660
320
500
660
500
660
500
660
500
660
500
660
Note) Weight of grommet type. Add 10 g for conduit type, 30 g for DIN
terminal type, 60 g for conduit terminal type respectively.
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
Note) Weight of grommet type. Add 10 g for conduit type, 30 g for DIN
terminal type, 60 g for conduit terminal type respectively.
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
Operating Fluid and Ambient Temperature
Power source
AC
DC
Operating fluid temperature (°C)
Solenoid valve option (symbol)
Nil, G
V, M
–10 Note) to 60
–10 Note) to 80
–10 Note) to 60
–10 Note) to 40
Note) Dew point temperature: –10°C or less
15
Ambient
temperature
(°C)
–20 to 60
–20 to 40
Tightness of Valve (Leakage Rate)
Leakage rate
Seal material
NBR, FKM
Air
1 cm3/min or less
Note)
Non-leak,
Medium vacuum
10–6 Pa·m3/sec or less
Note) Value on option “V”, “M” (non-leak, medium vacuum)
Direct Operated 2 Port Solenoid Valve
Series VX21/22/23
For Air/Single Unit
How to Order (Single Unit)
1 G1
1 G1
Model
Orifice size
Refer to the table (1)
shown below for availability.
Bracket
Refer to the table (1)
shown below for availability.
Nil
None
With bracket
B
Solenoid valve option
Refer to the table (2)
shown below for availability.
∗ Refer to the table (4) if a
bracket is ordered
separately.
Port size
For Oil
Normally Open (N.O.)
01
01
For Water
VX 21 2 0
VX 21 2 2
Normally Closed (N.C.)
—
Oil-free specification
Nil
Z
Select “Nil” because the solenoid valve
options “V”, “M” are the oil-free treatment.
1
2
3
4
5
6
7
8
J
100 VAC 50/60 Hz
200 VAC 50/60 Hz
110 VAC 50/60 Hz
220 VAC 50/60 Hz
24 VDC
Electrical entry
Rc
NPTF
G
NPT
T
F
N
G - Grommet
GS- With grommet surge
voltage suppressor
Rated voltage
T - With conduit terminal
TS - With conduit terminal and
12 VDC
240 VAC 50/60 Hz
48 VAC 50/60 Hz
230 VAC 50/60 Hz
and light
TZ - With conduit
terminal, surge
voltage suppressor
and light
Refer to page 2 for ordering coil only.
Port no.
(Port size)
01 (1 8 )
02 (1 4 )
—
—
—
—
02 (1 4 ) 02 (1 4 )
03 (3 8 ) 03 (3 8 )
04 (1 2 ) 04 (1 2 )
—
—
—
Orifice symbol (diameter)
1
2
3
4
5
6
VX23 (2 mmø) (3 mmø) (4.5 mmø) (6 mmø) (8 mmø) (10 mmø)
—
—
—
—
—
—
—
—
—
—
—
—
—
Normally Open (N.O.)
Orifice symbol (diameter)
Solenoid valve (Port size)
Model
Port no.
(Port size)
VX21
VX22
VX23
01 ( 1 8)
02 ( 1 4)
—
—
02 ( 1 4 )
03 ( 3 8)
—
—
02 ( 1 4 )
03 ( 3 8 )
—
—
voltage suppressor
and light
DO - For DIN (without connector)
∗ DIN type is available with class B insulation only.
Table (3) Rated Voltage – Electrical Entry –
Electrical Option
Solenoid valve (Port size)
VX22
suppressor
DL - DIN with light
DZ - DIN with surge
∗ Refer to the table (3) for the available combinations between each
electrical option (S, L, Z) and rated voltage.
Table (1) Port/Orifice Size
Normally Closed (N.C.)
VX21
D - DIN
Connector
DS - DIN with surge voltage
surge voltage suppressor
TL - With conduit terminal
∗ Refer to the table (3) shown below for availability.
Model
C- Conduit
1
(2 mmø)
2
3
4
(3 mmø) (4.5 mmø) (6 mmø)
—
—
—
—
Rated voltage
surge
AC/ Voltage Voltage With
voltage
DC symbol
suppressor
100 V
1
200 V
2
110 V
3
AC
220 V
4
240 V
7
48 V
8
230 V
J
24 V
5
DC
12 V
6
Model
1
Option
symbol
Nil
G
V
M
Seal
material
NBR
FKM
Body
Coil
Note
material
insulation type
Brass
—
Stainless steel
B
–6
Brass
Non-leak (10 Pam3/sec), Oil-free,
Medium vacuum (0.1 Pa.abs)
Stainless steel
L
Z
With
light
With light and
surge voltage
suppressor
—
—
—
—
—
—
—
—
Table (4) Bracket Part No.
VX21 2 0
Table (2) Solenoid Valve Option
Class B
S
3
2
Part no.
VX021N-12A
VX22 3 0
4
2
VX022N-12A
VX23 3 0
4
VX22 56 0
VX23 56 0
VX023N-12A-L
Please select the VCA series when using air because it is specifically designed for it.
(The VCA series is limited to air to improve its function and service life.)
Dimensions page 22 (Single unit)
16
For Air
Nil
Suffix
For Steam
Refer to the table (1) shown below for availability.
Thread type
Series VX21/22/23
For Air /Manifold
(Inert gas, Non-leak, Medium vacuum)
Solenoid Valve for Manifold/Valve Specifications
N.C.
N.O.
Passage symbol
2
Passage symbol
2
2
1
1
Common SUP type
Common SUP type
1
1
1
Orifice
size
(mmø)
1
2
2
Individual SUP type
Individual SUP type
Normally Closed (N.C.)
Model
VX2111-00
VX2121-00
VX2221-00
3
VX2321-00
VX2131-00
4.5 VX2231-00
VX2331-00
VX2241-00
6
VX2341-00
2
Normally Open (N.O.)
Max. operating
pressure
differential (MPa)
AC
2.0
1.1
2.0
3.0
0.45
0.75
1.0
0.4
0.5
DC
1.5
0.6
1.5
3.0
0.2
0.35
0.9
0.15
0.35
Flow
characteristics
C[dm3/(s·bar)]
b
Cv
Max. system
pressure
(MPa)
0.48
0.18
2
1.2
0.45
0.33
3
2.3
0.46
0.61
4.5
4.1
0.3
1.1
6
3.0
Operating Fluid and Ambient Temperature
Power source
AC
DC
Orifice
size
(mmø)
0.59
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
Operating fluid temperature (°C)
Solenoid valve option (symbol)
V
–10 Note) to 80
–10 Note) to 60
–10 Note) to 60
–10 Note) to 40
Note) Dew point temperature: –10°C or less
17
2
Ambient
temperature
(°C)
–20 to 60
–20 to 40
Model
VX2113-00
VX2123-00
VX2223-00
VX2323-00
VX2133-00
VX2233-00
VX2333-00
VX2243-00
VX2343-00
Max. operating
pressure
differential (MPa)
AC • DC
1.5
0.7
1.0
1.6
0.3
0.45
0.8
0.25
0.45
Flow
characteristics
C[dm3/(s·bar)]
b
Cv
0.59
0.48
0.18
1.2
0.45
0.33
2.3
0.46
0.61
4.1
0.3
1.1
Max. system
pressure
(MPa)
3.0
• Refer to “Glossary of Terms” on front matter 10 for details on the max.
operating pressure differential and the max. system pressure.
Tightness of Valve (Leakage Rate)
Leakage rate
Seal material
NBR, FKM
Air
1 cm3/min or less
Note)
Non-leak,
Medium vacuum
10–6 Pa·m3/sec or less
Note) Value on option “V”, “M” (non-leak, medium vacuum)
Direct Operated 2 Port Solenoid Valve
Series VX21/22/23
For Air/Manifold
How to Order (Solenoid Valve for Manifold)
Normally Open (N.O.)
Model
00 1 G 1
00 1 G 1
For Water
VX 21 2 1
VX 21 2 3
Normally Closed (N.C.)
Orifice size
Refer to the table (1)
shown below for availability.
Refer to the table (2)
shown below for availability.
Suffix
—
Oil-free specification
Z
Select “Nil” because the solenoid valve
option “V” is the oil-free treatment.
Electrical entry
Rated voltage
1
2
3
4
5
6
7
8
J
100 VAC 50/60 Hz
200 VAC 50/60 Hz
110 VAC 50/60 Hz
220 VAC 50/60 Hz
24 VDC
12 VDC
240 VAC 50/60 Hz
48 VAC 50/60 Hz
230 VAC 50/60 Hz
G - Grommet
GS- With grommet surge
C- Conduit
voltage suppressor
T - With conduit terminal
TS - With conduit terminal and
∗ Refer to the table (3) shown below for availability.
D - DIN
DS - DIN with surge voltage
surge voltage suppressor
suppressor
TL - With conduit terminal
Refer to page 2 for ordering coil only.
DL - DIN with light
DZ - DIN with surge
and light
TZ - With conduit
VVX21
VVX22 1
VVX23
07 1
Number of manifolds
1
2
02
2 stations
•
•
•
•
•
•
10
10 stations
Thread type
Port size
(Out port)
Nil
Rc
NPTF
G
NPT
T
F
N
Rc1/8
Rc1/4
voltage suppressor
and light
DO - For DIN (without connector)
∗ DIN type is available with class B insulation only.
terminal, surge
voltage
suppressor and light
How to Order Manifold Bases
For Air
Nil
∗ Refer to the table (3) for the available combinations between each
electrical option (S, L, Z) and rated voltage.
Table (1) Port/Orifice Size
Solenoid
valve
VX21
VX22
VX23
Orifice symbol (diameter)
1
2
3
4
(2 mmø)
—
—
(3 mmø)
(4.5 mmø)
(6 mmø)
—
Suffix
Nil
∗ All IN ports are Rc
3/8.
Z
—
Oil-free specification
Base
Manifold base
Nil
•Blanking plate part no.
V
Common SUP type
Individual SUP type
Table (2) Solenoid Valve Option
Option
symbol
Nil
V
For VX21: VX011-001
For VX22/23: VX011-006
Body, Base
material
Seal
material
Coil
insulation
type
Note
Aluminum
NBR
FKM
B
—
Non-leak specification
Please select the VCA series when using air because it is specifically
designed for it.
(The VCA series is limited to air to improve its function and service life.)
Seal material
Nil
NBR
FKM
F
Table (3) Rated Voltage – Electrical Option
How to Order Manifold Assemblies (Example)
Enter the valve and blanking plate to be mounted under the
manifold base part number.
Example
VVX211-05-1 ........ 1 set
∗ VX2111-00-1G1 ..... 4 sets
∗ VX011-001 ........... 1 set
Station
1
2
3
“∗” is the symbol for mounting.
Add an “∗” in front of the part numbers
for solenoid valves, etc. to be mounted.
4
5
n
Enter the product’s
part number in order,
counting the 1st station from the left in the
manifold arrangement,
when viewing the individual port in front.
Rated voltage
Class B
S
surge
AC/ Voltage Voltage With
voltage
DC symbol
suppressor
1
100 V
2
200 V
3
110 V
AC
4
220 V
7
240 V
8
48 V
J
230 V
5
24 V
DC
6
12 V
L
Z
With
light
With light and
surge voltage
suppressor
—
—
—
—
—
—
—
—
For Steam
Solenoid valve option
For Oil
Refer to the table (1)
shown below for availability.
Dimensions page 24 (manifold)
18
Low Power Consumption Type
Series VX21/22/23
For Water, Air
Solenoid Coil Electricity Specifications
Model
Rated voltage (V)
Power
Inrush
consumption
(W)
Holding
VX21
VX22
VX23
3
0.8
24 DC
4
0.8
5
0.8
Electric Circuit Diagram
Power saving circuit
With power saving circuit
24 V Applied voltage
(There is the polarity. Red (+), Black (–)
0V
Energy saving type/
100 to 200 ms
Electrical power waveform
Inrush
(Rated voltage 24 VDC)
Power saver
(Equivalent to IP40 enclosure)
Model/Valve Specifications
Holding
0W
N.C.
Normally closed (N.C.)
Max. operating
pressure
differential (MPa)
Orifice
size Model
(mmø)
Port
size
Av x 10-6 m2 Cv converted C[dm /(s·bar)]
0.17 0.59
4.1
0.33 1.2
7.9
0.61 2.4
15.0
0.17 0.59
4.1
3
DC
1.0
0.3
0.1
1.0
0.3
0.8
1.0
0.1
0.15
0.2
0.05
0.1
0.03
0.05
0.02
VX2110-01
18
VX2120-01
(6A)
VX2130-01
VX2110-02
VX2120-02
3 VX2220-02
VX2320-02
VX2130-02
4.5 VX2230-02
14
VX2330-02
(8A)
VX2240-02
6
VX2340-02
VX2250-02
8
VX2350-02
10 VX2360-02
2
3
4.5
2
Flow characteristics
7.9
0.33
15.0
0.61
1.2
2.3
b
0.48
0.45
0.44
0.48
Cv
0.18
0.33
0.61
0.18
Max. system
pressure
(MPa)
0.45 0.33
VX2220-03
3
VX2320-03
VX2230-03
4.5
VX2330-03
38
VX2240-03
(10A)
6
VX2340-03
VX2250-03
8
VX2350-03
10 VX2360-03
3.0
0.46 0.61
12
26.0
1.10
4.1
0.3
1.1
38.0
1.60
6.4
0.3
1.6
46.0
1.90
8.8
0.3
2.0
(15A)
Operating fluid temperature (°C)
Solenoid valve option (symbol)
Nil, G
1 to 40
DC
VX2360-04
10
Max. operating
pressure
differential (MPa)
Flow characteristics
DC
0.8
1.0
0.15
0.2
0.05
0.1
0.03
0.05
0.02
Av x 10-6 m2 Cv converted C[dm /(s·bar)]
0.02
3
b
Cv
7.9
0.33
1.2
0.45 0.33
15.0
0.61
2.3
0.46 0.61
26.0
1.10
4.1
0.3
1.1
38.0
1.60
6.4
0.3
1.6
53.0
2.20 11
0.3
2.2
53.0
2.20 11
0.3
2.2
Max. system
pressure
(MPa)
3.0
1.0
1.0
Tightness of Valve (Leakage Rate)
Operating Fluid and Ambient Temperature
Power source
Orifice
size Model
(mmø)
Port
size
Seal material
Ambient temperature
(°C)
NBR
Leakage rate
0.1 cm3/min or less (With water pressure)
1 cm3/min or less (Air)
–20 to 40
Note) With no condensation
How to Order (Single Unit)
Normally Closed (N.C.)
VX 21 2 0
Model
Nil
Suffix
Nil
Z
—
Oil-free specification
T
F
N
GY- Grommet
Rc
NPTF
G
NPT
5
Orifice symbol (diameter)
01 (1 8 )
02 (1 4 )
—
—
—
—
02 (1 4 ) 02 (1 4 )
03 (3 8 ) 03 (3 8 )
04 (1 2 ) 04 (1 2 )
—
—
—
19
Seal material Body material
NBR
Brass
Stainless steel
1
VX21 2 0
3
2
—
—
—
—
VX22 3 0
—
—
(VX23)
(VX23)
—
—
—
—
(VX23)
4
VX22 56 0
VX23 56 0
Table (2) Solenoid Valve Option
G
24 VDC
Model
1
2
3
4
5
6
VX23 (2 mmø) (3 mmø) (4.5 mmø) (6 mmø) (8 mmø) (10 mmø)
VX22
(With power saving
circuit)
Rated voltage
Table (3) Bracket Part No.
Solenoid valve (Port size)
VX21
Electrical entry
Thread type
Table (1) Port/Orifice Size
Normally Closed (N.C.)
Option
symbol
Nil
∗ Refer to the table (3) if bracket is
separately ordered.
Refer to the table (1) shown below for availability.
Nil
None
With bracket
B
Port size
Refer to the table (2)
shown below for availability.
—
—
—
Bracket
Refer to the table (1)
shown below for availability.
Solenoid valve option
Port no.
(Port size)
5 GY1
Orifice size
Refer to the table (1)
shown below for availability.
Model
01
Coil
insulation type
Operating fluid
B
Water, Air
4
2
Part no.
VX021N-12A
VX022N-12A
VX23 3 0
VX023N-12A-L
Direct Operated 2 Port Solenoid Valve
Series VX21/22/23
Construction: Single Unit
Normally closed (N.C.)
Body material: Brass, Stainless Steel
Normally open (N.O.)
Body material: Brass, Stainless Steel
u
u
e
t
w
w
t
i
e
y
y
r
r
q
IN
Component Parts
Component Parts
No.
Description
1
Body
2
Tube assembly
3
Armature assembly
4
Return spring
5
Solenoid coil
6
O-ring
7
Clip
q
IN
Material
Body material Brass specification
Body material stainless
steel specification
No.
Description
Material
Body material Brass specification
Body material stainless
steel specification
Brass
Stainless steel
1
Body
Stainless steel, Copper
Stainless steel, Silver
2
Tube assembly
(NBR, FKM, EPDM, PTFE) Stainless steel, PPS
3
Armature assembly
Stainless steel
4
Return spring
Stainless steel
Class B/H molded
5
Solenoid coil
Class B/H molded
(NBR, FKM, EPDM, PTFE)
6
O-ring
SK
7
Clip
8
Push rod assembly
The materials in parentheses are the seal materials.
Brass
Stainless steel
Stainless steel, Copper
Stainless steel, Silver
Stainless steel
(NBR, FKM, EPDM, PTFE)
SK
(NBR, FKM, EPDM, PTFE) Stainless steel, PPS
The materials in parentheses are the seal materials.
20
Series VX21/22/23
Construction: Manifold
Normally closed (N.C.)
Base material: Aluminum
Fluid: Air
Common SUP type
OUT
Normally open (N.O.)
Base material: Aluminum
Fluid: Air
Individual SUP type
Common SUP type
u
u
w
w
t
e
y
r
q
y
i
t
e
y
r
q
y
i
IN
IN port
u
e
t
u
e
t
w
i
w
i
y
r
q
y
r
o
OUT
q
o
IN
IN port
OUT port
Base material: Brass, Stainless Steel
Fluid: Water, Oil, Steam
Individual SUP type
OUT port
Base material: Brass, Stainless Steel
Fluid: Water, Oil, Steam
Common SUP type
Common SUP type
w
u
e
t
t
w
e
y
r
q
i
y
r
q
u
y
i
OUT
o
OUT
IN port
IN port
Component Parts
Component Parts
No.
Description
1
Body
2
Tube assembly
3
Armature assembly
Material
Base material
aluminum specification
Base material
brass specification
Base material stainless
steel specification
No.
Description
Material
Base material
aluminum specification
Base material
brass specification
Aluminum
Brass
Stainless steel
1
Body
Stainless steel, Silver
2
Tube assembly
(NBR, FKM, EPDM, PTFE) Stainless steel, PPS
3
Armature assembly
Return spring
Stainless steel
Class B/H molded
Aluminum
Brass
Stainless steel, Copper
Stainless steel, Copper
Base material stainless
steel specification
Stainless steel
Stainless steel, Silver
Stainless steel
Return spring
Stainless steel
4
5
Solenoid coil
Class B/H molded
5
Solenoid coil
6
O-ring
(NBR, FKM, EPDM, PTFE)
6
O-ring
7
Clip
SK
7
Clip
Brass
8
Push rod assembly
(NBR, FKM, EPDM, PTFE) Stainless steel, PPS
9
Base
Aluminum
4
8
Push rod assembly
Aluminum
The materials in parentheses are the seal materials.
Stainless steel
(NBR, FKM, EPDM, PTFE)
SK
Brass
The materials in parentheses are the seal materials.
21
Stainless steel
Series VX21/22/23
Direct Operated 2 Port Solenoid Valve
For Water, Oil, Steam
Dimensions: Single Unit/Body Material: Brass, Stainless Steel
Normally closed (N.C.): VX210/VX220/VX230
Normally open (N.O.): VX212/VX222/VX232
Conduit: C
M
M
25
Grommet: G
2-J, thread depth K
2-J, thread
depth K
Approx. 300
F
Approx. 280
D
Q
F
D
G1/2
25
Q
R
C
R
C
(C)
Width
across
flats H
E
E
Width across flats H
2-P
Port size
B
2-P
Port size
B
A
Conduit terminal: T
M
M
DIN terminal: D
A
Cable ø6
to ø12
2-J,
thread depth K
G1/2
2-J, thread depth K
F
Q
S
D
Q 2
F
34
G1/2
R
C
T
25
D
R
C
Width across flats H
E
Width across
flats H
E
S 2
B
2-P
Port size
A
2-ø5.3
Mounting hole
Bracket
A
Orifice ø8, ø10
U
W
Specifications with bracket
Orifice ø2, ø3, ø4.5, ø6
2-P
Port size
B
7.5
2.5
22
5.5
29
Bracket
X
28
Y
1.5
52
67
(mm)
Model
Normally closed Normally open
Orifice size
Port size
P
VX210 VX212 2¯ , ø3, ø4.5 1/8, 1/4
VX220 VX222 ø3, ø4.5, ø6 1/4, 3/8
1/4, 3/8, 1/2
ø8, ø10
—
VX220
VX230 VX232 ø3, ø4.5, ø6 1/4, 3/8
1/4, 3/8, 1/2
ø8, ø10
VX230
—
A
B
18 40
22 45
30 50
22 45
30 50
The figures in parentheses are the normally open type.
C
D
E
F
H
Electrical entry
Mounting
dimensions Grommet Conduit DIN terminal Conduit terminal
J
68 (76) 30 9 19.5 27 M4
78 (86)
10.5
M5
35
22.5 32
85 –
14
M5
85 (93)
10.5
M5
40
25 36
92 –
14
M5
K M Q
6
8
8
8
8
R
12.8 19.5 50
19
60
22.5
23
63
19
66
25
23
69
Q
R
Q
R
S
Q
R
S
T
Bracket
mounting
U W X
Y
40 42.5 58 42.5 46 95 42.5 62 85 46 36 11 15
52
52
52
96.5 56 46 13 17.5
43
61
49 98
65
55
55
55
103.5 – – – –
58
58
58
103
56 46 13 17.5
46
63
52 101
68
– – – –
61
61
61
111
22
Series VX21/22/23
For Water, Oil, Steam/Manifold
Dimensions: Manifold/Base Material: Brass, Stainless Steel
Normally closed (N.C.)
: VVX21/VVX22/VVX23
Normally open (N.O.)
Stations
1
2
3
4
U side
n
5
H
J
n-1/4, 1/8
OUT port
(Pitch)
2.5
D
F
Approx. 280
G1/2
33
Approx. 300
X±2
W
16
V
U
S
Q
C
B
A
E
N
H
L3
L2
L1
2-3/8
IN port
(N)
2
5.5
16
21
44
T
R
Y
D side
25
(mm)
n (stations)
Model
Dimension
2
3
4
5
6
7
8
L1
69
276
103.5
138
172.5
207
241.5
L2
VVX21
81
288
115.5
150
184.5
219
253.5
L3
93
300
127.5
162
196.5
231
265.5
L1
77
308
115.5
154
192.5
231
269.5
L2
89
320
127.5
166
204.5
243
281.5
VVX22
L3
101
332
139.5
178
216.5
255
293.5
L1
VVX23
83
332
124.5
166
207.5
249
290.5
L2
95
344
136.5
178
219.5
261
302.5
L3
107
356
148.5
190
231.5
273
314.5
Manifold composition 2 stns. x 1 3 stns. x 1 2 stns. x 2 2 stns. + 3 stns. 3 stns. x 2 2 stns. x 2 + 3 stns. 2 stns. + 3 stns. x 2
9
10
310.5
345
322.5
357
334.5
369
346.5
385
358.5
397
370.5
409
373.5
415
385.5
427
397.5
439
3 stns. x 3 2 stns. x 2 + 3 stns. x 2
(mm)
Model
VVX21
VVX22
VVX23
A
49
57
57
B
24.5
28.5
28.5
C
20
25.5
25.5
D
28
30
30
E
4.5
5.5
5.5
F
38
42
42
The figures in parentheses are the normally open type.
23
H
17.3
19.3
20.8
J
N
Grommet
Electrical entry
Conduit
DIN terminal
Conduit terminal
Q
R
S
T
U
V
W
X
Y
48
56
66.5
40
43
46
41.5
48
59
46
49
52
58
61
63
62
65
68
95
98
101
73
82
90.5
34.5 57 (65) 19.5
38.5 63,5 (72,5) 22.5
41.5 74 (82) 25
Direct Operated 2 Port Solenoid Valve
Series VX21/22/23
For Air/Manifold
Dimensions: Manifold/Base Material: Aluminum
Normally closed (N.C.)
: VVX21/VVX22/VVX23
Normally open (N.O.)
Stations
1
2
3
4
U side
n
5
D
E
T
R
44
Y
D side
F
H
F
n-1/8, 1/4
OUT port (Common SUP type)
IN port (Individual SUP type)
2-3/8
IN port (Common SUP type)
OUT port (Individual SUP type)
L2
(N)
K
N
L1
K
H
2 x øM
Approx. 280
G1/2
33
Approx. 300
X±2
W
V
U
S
J
Q
A
C
F
B(B)
A
D
25
(mm)
Model
VVX21
VVX22
VVX23
Dimension
L1
L2
L1
L2
2
86
100
108
126
3
122
136
154
172
4
158
172
200
218
n (stations)
5
6
7
194
230
266
208
244
280
246
292
338
264
310
356
8
302
316
384
402
9
338
352
430
448
10
374
388
476
494
(mm)
Grommet
Electrical entry
Conduit
DIN terminal
Conduit terminal
Q
R
S
T
U
V
W
X
Y
19.5
22.5
25
48
58
63
40
43
46
41,5
51
56
46
49
52
58
61
63
62
65
68
95
98
101
73
82
87
(B)
Model
VVX21
VVX22
VVX23
A
38
49
49
B
20.5
26.5
26.5
Individual
SUP
type
C
17.5
22.5
22.5
10.5
13
13
D
11
13
13
E
25
30
30
F
32
40
40
H
36
46
46
J
12
15
15
K
7
9
9
M
6.5
8.5
8.5
N
57 (65)
66 (74)
71 (79)
The figures in parentheses are the normally open type.
24
Series VX
Safety Instructions
The following safety instructions are intended to prevent a hazardous situation
and/or equipment damage. These instructions indicate the level of potential hazard
by all safety practices, including labels of "Caution", "Warning" or "Danger". To
ensure safety, please observe ISO 4414 Note 1), JIS B 8370 Note 2).
Caution: Operator error could result in injury or equipment damage.
Warning : Operator error could result in serious injury or loss of life.
Danger : In extreme conditions, there is a possible result of serious injury or loss of life.
Note 1) ISO 4414: Pneumatic fluid power – General rules relating to systems
Note 2) JIS B 8370: General Rules for Pneumatic Equipment
Warning
1. The compatibility of equipment is the responsibility of the person who
designs the system or decides its specifications.
Since the products specified here are used in various operating conditions, their compatibility with a
specific system must be based on specifications, post analysis and/or tests to meet a specific
requirement. The expected performance and safety assurance will be the responsibility of the person
who has determined the compatibility of the system. This person should continuously review the
suitability of all items specified, referring to the latest catalog information and taking into consideration
the possibility of equipment failure when configuring a system. Be particularly careful in determining
the compatibility with the fluid to be used.
2. Only trained personnel should operate machinery and equipment.
The fluid can be dangerous if handled incorrectly. Assembly, handling or maintenance of the system
should be performed by trained and experienced operators.
3. Do not service machinery/equipment or attempt to remove components until
the safety is confirmed.
1. Inspection and maintenance of machinery/equipment should only be performed once measures to
prevent falling or runaway of the driven object have been confirmed. Measures to prevent danger
from a fluid should also be confirmed.
2. When equipment is to be removed, confirm the safety processes mentioned above, release the fluid
pressure and be certain there is no danger from fluid leakage or fluid remaining in the system.
3. Carefully restart the machinery, confirming that safety measures are being implemented.
4. Contact SMC if the product is to be used in any of the following conditions:
1. Conditions and environments beyond the given specifications, or if product is used outdoors.
2. With fluids whose application causes concern due to the type of fluid or additives, etc.
3. An application which has the possibility of having a negative effect on people, property, or animals,
and therefore requires special safety analysis.
Back page 1
2 Port Solenoid Valve for Fluid Control/Precautions 1
Be sure to read before handling.
For detailed precautions on each series, refer to the main text.
Design
Selection
Warning
Warning
1. Cannot be used as an emergency shutoff valve, etc.
The valves presented in this catalog are not designed for safety
applications such as an emergency shutoff valve. If the valves
are used in this type of system, other reliable safety assurance
measures should also be adopted.
2. Extended periods of continuous energization
The solenoid coil will generate heat when continuously energized. Avoid using in a tightly shut container. Install it in a wellventilated area. Furthermore, do not touch it while it is being
energized or right after it is energized.
3. This solenoid valve cannot be used for explosion proof applications.
4. Maintenance space
The installation should allow sufficient space for maintenance
activities (removal of valve, etc.).
5. Liquid rings
In cases with a flowing liquid, provide a bypass valve in the
system to prevent the liquid from entering the liquid seal circuit.
3) Corrosive gas
Cannot be used since it will lead to cracks by stress corrosion
or result in other incidents.
4) Use an oil-free specification when any oily particle must not
enter the passage.
5) Applicable fluid on the list may not be used depending on the
operating condition. Give adequate confirmation, and then
determine a model, just because the compatibility list shows
the general case.
3. Fluid quality
The use of a fluid which contains foreign matter can cause problems such as malfunction and seal failure by promoting wear of
the valve seat and armature, and by sticking to the sliding parts
of the armature, etc. Install a suitable filter (strainer) immediately
upstream from the valve. As a general rule, use 80 to 100 mesh.
When used to supply water to boilers, substances such as
calcium and magnesium which generate hard scale and sludge
are included. Since this scale and sludge can cause the valve to
malfunction, install water softening equipment, and a filter
(strainer) directly upstream from the valve to remove these
substances.
4. Air quality
6. Actuator drive
When an actuator, such as a cylinder, is to be driven using a
valve, take appropriate measures to prevent potential danger
caused by actuator operation.
7. Pressure (including vacuum) holding
It is not usable for an application such as holding the pressure
(including vacuum) inside of a pressure vessel because air leakage is entailed in a valve.
8. When the conduit type is used as equivalent
to an IP65 enclosure, install a wiring conduit,
etc.
9. When an impact, such as water hammer, etc.,
caused by the rapid pressure fluctuation is
applied, the solenoid valve may be damaged.
Give an attention to it.
Selection
Warning
1. Confirm the specifications.
Give careful consideration to the operating conditions such as
the application, fluid and environment, and use within the operating ranges specified in this catalog.
2. Fluid
1) Type of fluid
Before using a fluid, confirm whether it is compatible with the
materials from each model by referring to the fluids listed in
this catalog. Use a fluid with a dynamic viscosity of 50 mm2/s
or less. If there is something you do not know, please contact
us.
2) Inflammable oil, Gas,
Confirm the specification for leakage in the interior and/or exterior area.
1) Use clean air.
Do not use compressed air which includes chemicals, synthetic oils containing organic solvents, salt or corrosive gases,
etc., as it can cause damage or malfunction.
2) Install air filters.
Install air filters close to valves at their upstream side. A filtration degree of 5µm or less should be selected.
3) Install an air dryer or after cooler, etc.
Compressed air that includes excessive drainage may cause
malfunction of valves and other pneumatic equipment. To
prevent this, install an air dryer or after cooler, etc.
4) If excessive carbon powder is generated, eliminate it by
installing mist separators at the upstream side of valves.
If excessive carbon powder is generated by the compressor,
it may adhere to the inside of the valves and cause a malfunction.
Refer to SMC’s Best Pneumatics catalog Vol. 14 for further details on compressed air quality.
5. Ambient environment
Use within the operable ambient temperature range. Confirm
the compatibility between the product’s composition materials
and the ambient atmosphere. Be sure that the fluid used does
not touch the external surface of the product.
6. Countermeasures against static electricity
Take measures to prevent static electricity since some fluids can
cause static electricity.
7. For the low particle generation specification,
confirm us separately.
Back page 2
2 Port Solenoid Valve for Fluid Control/Precautions 2
Be sure to read before handling.
For detailed precautions on each series, refer to the main text.
Selection
Piping
Caution
Caution
1. Leakage voltage
1. Preparation before piping
Particularly when using a resistor in parallel with a switching
element and using a C-R element (surge voltage suppressor) to
protect the switching element, take note that leakage current
will flow through the resistor, C-R element, etc., creating a possible danger that the valve may not turn off.
Power supply
Switching element
Leakage voltage
OFF
C
R
Valve
Before piping is connected, it should be thoroughly blown out
with air (flushing) or washed to remove chips, cutting oil and other debris from inside the pipe.
2. Wrapping of pipe tape
When connecting pipes, fittings, etc., be sure that chips from the
pipe threads and sealing material do not enter the valve.
Furthermore, when pipe tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads.
Leakage current
Winding
direction
AC coil: 20% or less of rated voltage
DC coil: 2% or less of rated voltage
Ex
po
se
2. Low temperature operation
1. The valve can be used in an ambient temperature of between
–10 to –20°C, however take measures to prevent freezing or
solidification of impurities, etc.
2. When using valves for water application in cold climates, take
appropriate countermeasures to prevent the water from freezing in tubing after cutting the water supply from the pump,
by draining the water, etc. When heating by steam, be careful not to expose the coil portion to steam. Installation of
dryer, heat retaining of the body is recommended to prevent
a freezing condition in which the dew point temperature is
high and the ambient temperature is low, and the high flow
runs.
Mounting
Warning
1. If air leakage increases or equipment does
not operate properly, stop operation.
After mounting is completed, confirm that it has been done correctly by performing a suitable function test.
2. Do not apply external force to the coil section.
When tightening is performed, apply a wrench or other tool to
the outside of the piping connection parts.
3. Be sure not to position the coil downwards.
When mounting a valve with its coil positioned downwards, foreign objects in the fluid will adhere to the iron core leading to a
malfunction.
4. Do not warm the coil assembly with a heat insulator, etc.
Use tape, heaters, etc., for freeze prevention on the piping and
body only. They can cause the coil to burn out.
5. Secure with brackets, except in the case of
steel piping and copper fittings.
6. Avoid sources of vibration, or adjust the arm
from the body to the minimum length so that
resonance will not occur.
7. Painting and coating
Warnings or specifications printed or labeled on the product
should not be erased, removed or covered up.
Back page 3
Pipe tape
ap
pro
x.
2t
hre
ad
s
3. Avoid connecting ground lines to piping, as
this may cause electric corrosion of the
system.
4. Always tighten threads with the proper tightening torque.
When attaching fittings to valves, tighten with the proper tightening torque shown below.
Tightening Torque for Piping
Rc 1/8
Proper tightening torque N ⋅ m
7 to 9
Rc 1/4
12 to 14
Rc 3/8
22 to 24
Rc 1/2
28 to 30
Connection threads
5. Connection of piping to products
When connecting piping to a product, refer to its instruction
manual to avoid mistakes regarding the supply port, etc.
6. Steam generated in a boiler contains a large
amount of drainage.
Be sure to operate it with a drain trap installed.
7. In applications such as vacuum and non-leak
specifications, use caution specifically
against the contamination of foreign matters
or airtightness of the fittings.
2 Port Solenoid Valve for Fluid Control/Precautions 3
Be sure to read before handling.
For detailed precautions on each series, refer to the main text.
Wiring
Grommet
Class H coil: AWG18 Insulator O.D. 2.2 mm
Class B coil: AWG20 Insulator O.D. 2.4 mm
Lead wire color
Rated voltage
DC (Class B only)
Black
Red
100 VAC
Blue
Blue
200 VAC
Red
Red
Other AC
Gray
Gray
∗ There is no polarity. (For the low power consumption type, there is polarity.)
DIN connector (Class B only)
Since internal connections are as shown below for the DIN connector,
make connections to the power supply accordingly.
1: +
2
1
(–)
+
1. As a rule, use electrical wire with a cross sectional area of 0.5 to 1.25mm2 for wiring.
Furthermore, do not allow excessive force to
be applied to the lines.
2. Use electrical circuits which do not generate
chattering in their contacts.
3. Use voltage which is within ±10% of the rated
voltage. In cases with a DC power supply
where importance is placed on responsiveness, stay within ±5% of the rated value. The
voltage drop is the value in the lead wire section connecting the coil.
4. When a surge from the solenoid affects the
electrical circuitry, install a surge absorber,
etc., in parallel with the solenoid.
Or, adopt an option that comes with the surge
voltage protection circuit. (However, a surge
voltage occurs even if the surge voltage protection circuit is used. For details, please consult with us.)
Caution
3
Caution
Electrical Connections
—
2: –
(+)
Terminal no.
1
2
DIN terminal
+ (–)
– (+)
∗ There is no polarity.
• Use compatible heavy duty cords with cable O.D. of ø6 to 12.
• Use the tightening torques below for each section.
Connector
Binding head screw with flange
Tightening torque 0.5 to 0.6 N⋅m
Note)
Washer
Compatible cable
(cable O.D. ø6 to 12 mm)
Rubber seal
Binding head screw
Tightening torque 0.5 to 0.6 N⋅m
Gasket
Note) For an outside cable diameter of ø9 to 12 mm, remove the
internal parts of the rubber seal before using.
Back page 4
2 Port Solenoid Valve for Fluid Control/Precautions 4
Be sure to read before handling.
For detailed precautions on each series, refer to the main text.
Electrical Connections
Electrical Circuits
Caution
Caution
Conduit terminal
Grommet, Conduit, Conduit terminal, DIN connector
In the case of the conduit terminal, make connections according to
the marks shown below.
• Use the tightening torques below for each section.
• Properly seal the terminal connection (G1/2) with the special wiring conduit, etc.
Terminal cover
2
-
1
+
+ mark
– mark
Round head
combination screw
M3 Tightening torque
0.5 to 0.6 N⋅m
DC circuit
AC circuit
1 (+, –)
1
SOL.
SOL.
2 (–, +)
A
2
Without electrical option
G1/2
Tightening torque
0.5 to 0.6 N⋅m
Without electrical option
Conduit terminal, DIN connector
A
DC circuit
AC circuit
1
1 (+, –)
Round head
combination screw
M3 Tightening torque
0.5 to 0.6 N⋅m
SOL.
SOL.
Conduit terminal
2
2 (–, +)
Light
Light
View A-A
(Internal connection diagram)
With light
With light
Conduit
When used as an IP65 equivalent, use seal (part no. VCW20-15-6)
to install the wiring conduit. Also, use the tightening torque below
for the conduit.
Class H coil: AWG18 Insulator O.D. 2.2 mm
ZNR
1 (+, –)
ZNR
1
SOL.
2 (–, +)
Class B coil: AWG20 Insulator O.D. 2.4 mm
SOL.
2
Light
Light
Lead wire
With light/surge voltage suppressor
With light/surge voltage suppressor
Grommet, Conduit terminal, DIN connector
Seal (VCW20-15-6)
Wiring conduit
Bore size G1/2 Tightening torque 0.5 to 0.6 N⋅m
DC circuit
AC circuit
ZNR
Lead wire color
Rated voltage
DC
Black
Red
100 VAC
Blue
Blue
200 VAC
Red
Red
Other AC
Gray
Gray
∗ There is no polarity for DC. (For the low power consumption type, there is polarity.)
Description
Part no.
Seal
VCW20-15-6
Note) Please order separately.
Back page 5
ZNR
1
1 (+, –)
SOL.
2 (–, +)
With surge voltage suppressor
SOL.
2
With surge voltage suppressor
2 Port Solenoid Valve for Fluid Control/Precautions 5
Be sure to read before handling.
For detailed precautions on each series, refer to the main text.
Operating Environment
Warning
Maintenance
Caution
1. Do not use the valves in an atmosphere having corrosive gases, chemicals, salt water,
water, steam, or where there is direct contact
with any of these.
2. Do not use in explosive atmospheres.
3. Do not use in locations subject to vibration or
impact.
4. Do not use in locations where radiated heat
will be received from nearby heat sources.
5. Employ suitable protective measures in locations where there is contact with water droplets, oil or welding spatter, etc.
1. Filters and strainers
1. Be careful regarding clogging of filters and strainers.
2. Replace filter elements after one year of use, or earlier if the
pressure drop reaches 0.1 MPa.
3. Clean strainers when the pressure drop reaches 0.1 MPa.
2. Lubrication
When using after lubricating, never forget to lubricate continuously.
3. Storage
In case of long term storage after use with heated water, thoroughly remove all moisture to prevent rust and deterioration of
rubber materials, etc.
4. Exhaust the drain from an air filter periodically.
Lubrication
Operating Precautions
Caution
1. This solenoid valve can be operated without
lubrication.
If a lubricant is used in the system, use turbine oil Class 1, ISO
VG32 (with no additive). But do not lubricate a valve with EPDM
seal.
Refer to the table of brand name of lubricants compliant with
Class 1 turbine oil (with no additive), ISO VG32.
Warning
1. Valves will reach high temperatures from
high temperature fluids. Use caution, as there
is a danger of being burned if a valve is touched directly.
Class 1 Turbine Oil (with no additive), ISO VG32
Classification of
viscosity (cst)
(40°C)
Viscosity
according to
ISO Grade
32
Turbine oil P-32
Idemitsu Kosan Co.,Ltd.
Turbine oil 32
Nippon Mitsubishi Oil Corp.
Cosmo Oil Co.,Ltd.
Cosmo turbine 32
Japan Energy Corp.
Kyodo turbine 32
Kygnus Oil Co.
Turbine oil 32
Kyushu Oil Co.
Stork turbine 32
Nippon Mitsubishi Oil Corp.
Mitsubishi turbine 32
Turbine 32
Showa Shell Sekiyu K.K.
Tonen General Sekiyu K.K.
General R turbine 32
Fucoal turbine 32
Fuji Kosan Co.,Ltd.
Please contact SMC regarding Class 2 turbine oil (with additives), ISO VG32.
Maintenance
Warning
1 Removing the product
The valve will reach a high temperature when used with high
temperature fluids. Confirm that the valve temperature has
dropped sufficiently before performing work. If touched inadvertently, there is a danger of being burned.
1. Shut off the fluid supply and release the fluid pressure in the
system.
2. Shut off the power supply.
3. Demount the product.
2. Low frequency operation
Switch valves at least once every 30 days to prevent malfunction.
Also, in order to use it under the optimum state, conduct a regular
inspection once a half year.
Back page 6
EUROPEAN SUBSIDIARIES:
Austria
SMC Pneumatik GmbH (Austria).
Girakstrasse 8, A-2100 Korneuburg
Phone: +43 2262-62280, Fax: +43 2262-62285
E-mail: [email protected]
http://www.smc.at
France
SMC Pneumatique, S.A.
1, Boulevard de Strasbourg, Parc Gustave Eiffel
Bussy Saint Georges F-77607 Marne La Vallee Cedex 3
Phone: +33 (0)1-6476 1000, Fax: +33 (0)1-6476 1010
E-mail: [email protected]
http://www.smc-france.fr
Netherlands
SMC Pneumatics BV
De Ruyterkade 120, NL-1011 AB Amsterdam
Phone: +31 (0)20-5318888, Fax: +31 (0)20-5318880
E-mail: [email protected]
http://www.smcpneumatics.nl
Spain
SMC España, S.A.
Zuazobidea 14, 01015 Vitoria
Phone: +34 945-184 100, Fax: +34 945-184 124
E-mail: [email protected]
http://www.smces.es
Belgium
SMC Pneumatics N.V./S.A.
Nijverheidsstraat 20, B-2160 Wommelgem
Phone: +32 (0)3-355-1464, Fax: +32 (0)3-355-1466
E-mail: [email protected]
http://www.smcpneumatics.be
Germany
SMC Pneumatik GmbH
Boschring 13-15, D-63329 Egelsbach
Phone: +49 (0)6103-4020, Fax: +49 (0)6103-402139
E-mail: [email protected]
http://www.smc-pneumatik.de
Norway
SMC Pneumatics Norway A/S
Vollsveien 13 C, Granfos Næringspark N-1366 Lysaker
Tel: +47 67 12 90 20, Fax: +47 67 12 90 21
E-mail: [email protected]
http://www.smc-norge.no
Sweden
SMC Pneumatics Sweden AB
Ekhagsvägen 29-31, S-141 71 Huddinge
Phone: +46 (0)8-603 12 00, Fax: +46 (0)8-603 12 90
E-mail: [email protected]
http://www.smc.nu
Bulgaria
SMC Industrial Automation Bulgaria EOOD
16 kliment Ohridski Blvd., fl.13 BG-1756 Sofia
Phone:+359 2 9744492, Fax:+359 2 9744519
E-mail: [email protected]
http://www.smc.bg
Greece
S. Parianopoulus S.A.
7, Konstantinoupoleos Street, GR-11855 Athens
Phone: +30 (0)1-3426076, Fax: +30 (0)1-3455578
E-mail: [email protected]
http://www.smceu.com
Poland
SMC Industrial Automation Polska Sp.z.o.o.
ul. Konstruktorska 11A, PL-02-673 Warszawa,
Phone: +48 22 548 5085, Fax: +48 22 548 5087
E-mail: [email protected]
http://www.smc.pl
Switzerland
SMC Pneumatik AG
Dorfstrasse 7, CH-8484 Weisslingen
Phone: +41 (0)52-396-3131, Fax: +41 (0)52-396-3191
E-mail: [email protected]
http://www.smc.ch
Croatia
SMC Industrijska automatika d.o.o.
Crnomerec 12, 10000 ZAGREB
Phone: +385 1 377 66 74, Fax: +385 1 377 66 74
E-mail: [email protected]
http://www.smceu.com
Hungary
SMC Hungary Ipari Automatizálási Kft.
Budafoki ut 107-113, H-1117 Budapest
Phone: +36 1 371 1343, Fax: +36 1 371 1344
E-mail: [email protected]
http://www.smc-automation.hu
Portugal
SMC Sucursal Portugal, S.A.
Rua de Engº Ferreira Dias 452, 4100-246 Porto
Phone: +351 22-610-89-22, Fax: +351 22-610-89-36
E-mail: [email protected]
http://www.smces.es
Turkey
Entek Pnömatik San. ve Tic Ltd. Sti.
Perpa Tic. Merkezi Kat: 11 No: 1625, TR-80270 Okmeydani Istanbul
Phone: +90 (0)212-221-1512, Fax: +90 (0)212-221-1519
E-mail: [email protected]
http://www.entek.com.tr
Czech Republic
SMC Industrial Automation CZ s.r.o.
Hudcova 78a, CZ-61200 Brno
Phone: +420 5 414 24611, Fax: +420 5 412 18034
E-mail: [email protected]
http://www.smc.cz
Ireland
SMC Pneumatics (Ireland) Ltd.
2002 Citywest Business Campus, Naas Road, Saggart, Co. Dublin
Phone: +353 (0)1-403 9000, Fax: +353 (0)1-464-0500
E-mail: [email protected]
http://www.smcpneumatics.ie
Romania
SMC Romania srl
Str Frunzei 29, Sector 2, Bucharest
Phone: +40 213205111, Fax: +40 213261489
E-mail: [email protected]
http://www.smcromania.ro
Denmark
SMC Pneumatik A/S
Knudsminde 4B, DK-8300 Odder
Phone: +45 70252900, Fax: +45 70252901
E-mail: [email protected]
http://www.smc-pneumatik.com
Italy
SMC Italia S.p.A
Via Garibaldi 62, I-20061Carugate, (Milano)
Phone: +39 (0)2-92711, Fax: +39 (0)2-9271365
E-mail: [email protected]
http://www.smcitalia.it
Russia
SMC Pneumatik LLC.
Sredny pr. 36/40, St. Petersburg 199004
Phone.:+812 118 5445, Fax:+812 118 5449
E-mail: [email protected]
http://www.smc-pneumatik.ru
Estonia
SMC Pneumatics Estonia OÜ
Laki 12-101, 106 21 Tallinn
Phone: +372 (0)6 593540, Fax: +372 (0)6 593541
E-mail: [email protected]
http://www.smcpneumatics.ee
Latvia
SMC Pneumatics Latvia SIA
Smerla 1-705, Riga LV-1006, Latvia
Phone: +371 781-77-00, Fax: +371 781-77-01
E-mail: [email protected]
http://www.smclv.lv
Slovakia
SMC Priemyselná Automatizáciá, s.r.o.
Námestie Martina Benku 10, SK-81107 Bratislava
Phone: +421 2 444 56725, Fax: +421 2 444 56028
E-mail: [email protected]
http://www.smc.sk
Finland
SMC Pneumatics Finland OY
PL72, Tiistinniityntie 4, SF-02031 ESPOO
Phone: +358 207 513513, Fax: +358 207 513595
E-mail: [email protected]://www.smc.fi
Lithuania
SMC Pneumatics Lietuva, UAB
Savanoriu pr. 180, LT-01354 Vilnius, Lithuania
Phone: +370 5 264 81 26, Fax: +370 5 264 81 26
Slovenia
SMC industrijska Avtomatika d.o.o.
Grajski trg 15, SLO-8360 Zuzemberk
Phone: +386 738 85240 Fax: +386 738 85249
E-mail: [email protected]
http://www.smc-ind-avtom.si
© DiskArt™ 1988
UK
SMC Pneumatics (UK) Ltd
Vincent Avenue, Crownhill, Milton Keynes, MK8 0AN
Phone: +44 (0)800 1382930 Fax: +44 (0)1908-555064
E-mail: [email protected]
http://www.smcpneumatics.co.uk
© DiskArt™
OTHER SUBSIDIARIES WORLDWIDE:
ARGENTINA, AUSTRALIA, BOLIVIA, BRASIL, CANADA, CHILE,
CHINA, HONG KONG, INDIA, INDONESIA, MALAYSIA, MEXICO,
NEW ZEALAND, PHILIPPINES, SINGAPORE, SOUTH KOREA,
TAIWAN, THAILAND, USA, VENEZUELA
http://www.smceu.com
http://www.smcworld.com
SMC CORPORATION
1st printing JU printing JU 10 UK Printed in Spain
1-16-4 Shimbashi, Minato-ku, Tokio 105 JAPAN; Phone:03-3502-2740 Fax:03-3508-2480
Specifications are subject to change without prior notice
and any obligation on the part of the manufacturer.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement