2 - Industrial Relays
Plug-in / PCB Relays - Overview
Rated
current
No. of
Contacts
Features
Sockets
30 Series
2A
2 CO
Subminiature DIL relays
- 2 Pole changeover contacts
- Low level switching capability
- Subminiature: - industry standard DIL package
- Sensitive DC coil: 200 mW
- Wash tight: RT III
32 Series
6A
1 CO
1 NO
Subminiature PCB relays
- 1 Pole changeover contacts or 1 Pole normally open contact
- Subminiature, low profile package
- Sensitive DC coil: 200 mW
- Wash tight: RT III
6A
1 CO
1 NO
Ultra-slim Electromechanical PCB relays
- Sensitive DC coil: 170 mW
- 5 mm wide
- 6kV (1.2/50 µs) isolation, coil - contacts
1 output
(SSR)
Ultra-slim Solid State PCB relays
- Sensitive DC input circuits
- 5 mm wide
- Silent, high speed switching with long electrical life
10 A
1 CO
1 NO
Printed circuit relay
- 1 Pole changeover contacts or 1 Pole normally open contact
- Miniature “Sugar Cube” package
- DC coil: 360 mW
- Wash tight: RT III
12 A
16 A
1 CO
1 NO
Miniature PCB relay
- DC coils
- 8mm, 6kV (1.2/50 µs) isolation, coil - contacts
- Flux proof: RT II standard
- 3.5 or 5 mm pin pitch
10 A
16 A
8A
1
1
2
2
CO
NO
CO
NO
Miniature PCB/plug-in relay
- DC coils & AC coils
- 8mm, 6kV (1.2/50 µs) isolation, coil - contacts
- 3.5 or 5 mm pin pitch
12 A
16 A
1 CO
93 Series
8A
2 CO
Low profile electromechanical PCB relay
- Low profile, 15.7 mm height
- DC coils: 400mW
- 8mm, 6kV (1.2/50 µs) isolation, coil - contacts
- Flux proof: RT II standard, (RT III option)
3A
5A
1 output
(SSR)
Low profile Solid State PCB relay
- Low profile, 15.7 mm height
- Sensitive DC input circuits
- Silent, high speed switching with long electrical life
95 Series
1 CO
1 NO
Low profile PCB relay
- Low profile, 15.4 mm height
- Sensitive DC coils: 250mW or 400mW
- Very high coil contact isolation 10mm, 6kV (1.2/50 µs)
- Flux proof: RT II standard, (RT III option)
- 3.2 or 5mm pin pitch
95 Series
Miniature PCB relay
- High physical separation between adjacent contacts
- DC coils
- 8mm, 6kV (1.2/50 µs) isolation, coil - contacts
- Flux proof: RT II
- 5mm pin pitch
95 Series
34 Series
0.1 A
2 A
36 Series
40 Series
41 Series
43 Series
44 Series
45 Series
10 A
16 A
6A
10 A
16 A
2 CO
1 NO
1 NC
93 Series
95 Series
Miniature PCB relay
- Relay for +125°C ambient use
- Contact gap ≥ 3mm according to EN 60730-1
- 8mm, 6kV (1.2/50 µs) isolation, coil - contacts
- Sensitive DC coil: 360mW
- PCB mounting + Faston 250
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
Plug-in / PCB Relays - Overview
Rated
current
8A
No. of
Contacts
2 CO
46 Series
16 A
50 Series
1 CO
8A
2 CO
10 A
2 CO
3 CO
55 Series
7A
56 Series
60 Series
62 Series
12 A
6A
10 A
16 A
20 A
Miniature industrial relays
- Socket mount or direct connection via Faston connectors
- AC & DC coils
- Available with lockable test button, mechanical flag & LED indicator
- 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts
Sockets
97 Series
Safety relay (EN 50205)
- 2 Pole changeover contacts
- PCB Relay with forcibly guided contacts according to EN 50205 type B
- High physical separation between adjacent contacts
- 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts
- Flux proof: RT II
General purpose relays
- AC & DC coils
- PCB or Plug-in mounting
- Available with lockable test button, mechanical flag & LED indicator
94 Series
4 CO
CO
NO
CO
NO
Miniature power relays
- PCB or Plug-in mounting
- Flange mount option (Faston 187 termination)
- AC & DC coils
- Available with lockable test button, mechanical flag & LED indicator
96 Series
2 CO
3 CO
General purpose relays
- 8 & 11 pin plug-in
- Flange mount
- AC & DC coils, “current sensing relays” or “intensity relays”
- Available with lockable test button, mechanical flag & LED indicator
- Version with bifurcated contacts for low level switching
90 Series
2
2
3
3
Power relays
- PCB mount or Plug-in mount (Faston 187) or
Flange mount (Faston 250)
- AC & DC coils
- NO contacts options, > 3mm contact gap
- LED, mechanical indicator & test button options
92 Series
2
2
4
4
CO
NO
CO
NO
1 NO +
1 NC
65 Series
66 Series
Features
30 A
1 NO
30 A
2 CO
2 NO
Power relays
- AC & DC coils
- PCB mount or Flange mount (Faston 250)
- NO version, > 3mm contact gap
Power relays
- PCB mount or Flange mount (Faston 250)
- AC & DC coils
- 8mm, 6kV (1.2/50 µs) isolation, coil - contacts
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
46
SERIES
46 Series - Miniature industrial relays 8 - 16 A
Features
46.61
46.52
Socket mount or direct connection via Faston
connectors
• AC coils & DC coils
• Available with: lockable test button,
mechanical indicator & LED indicator
• 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts
• Cadmium Free contacts
• European Patent
Plug-in / PCB Relays
1 & 2 Pole relay range
46.52 - 2 Pole 8 A
46.61 - 1 Pole 16 A
•
•
•
2 Pole CO, 8 A
Plug-in/Solder terminals
•
•
1 Pole CO, 16 A
Plug-in/Faston 187
46.52
12.4
20
32.8
29
4.75
0.5
6.5
46.61
4.75
FOR UL RATINGS SEE:
“General technical information” page V
Contact specification
Contact configuration
Rated current/Maximum peak current
A
Rated voltage/Maximum switching voltage V AC
2 CO (DPDT)
1 CO (SPDT)
8/15
16/25 *
250/440
250/440
Rated load AC1
VA
2,000
4,000
Rated load AC15 (230 V AC)
VA
350
750
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
Standard contact material
0.37
0.55
6/0.5/0.15
12/0.5/0.15
300 (5/5)
300 (5/5)
AgNi
AgNi
* With the AgSnO2 material
the maximum peak current is
80 A - 5 ms on normally
open contact.
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
12 - 24 - 48 - 110 - 120 - 230 - 240
V DC
Rated power
VA/W
12 - 24 - 48 - 110 - 125
1.2/0.5
1.2/0.5
AC
(0.8...1.1)UN
(0.8...1.1)UN
DC
(0.73...1.1)UN
(0.73...1.1)UN
Holding voltage
AC/DC
0.8UN /0.4UN
0.8UN /0.4UN
Must drop-out voltage
AC/DC
0.2UN /0.1UN
0.2UN /0.1UN
10 · 106
10 · 106
Operating range
Technical data
Mechanical life AC/DC
Electrical life at rated load AC1
X-2013, www.findernet.com
Operate/release time
cycles
cycles
ms
Insulation between coil and contacts (1.2/50 µs)kV
Dielectric strength between open contacts V AC
Ambient temperature range
Environmental protection
°C
3
100 · 10
100 · 103
10/3
15/5
6 (8 mm)
6 (8 mm)
1,000
1,000
–40 ... +70
–40 ... +70
RT II
RT II
Approvals (according to type)
1
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
46
SERIES
46 Series - Miniature industrial relays 8 - 16 A
Ordering information
Plug-in / PCB Relays
Example: 46 series Miniature industrial relay, 1 CO (SPDT), 24 V DC coil, lockable test button and mechanical indicator.
4 6. 6
A
B
C
D
1 . 9 . 0 2 4 . 0
0
4
0
A: Contact material
0 = AgNi
4 = AgSnO2 (46.61 only)
5 = AgNi + Au
Series
Type
5 = Spade/blade solder terminal
(2.5x0.5)mm
6 = Spade/blade terminal
Faston 187 (4.8x0.5)mm
D: Special versions
0 = Standard
C: Options
2 =Mechanical indicator
4 =Lockable test button +
mechanical indicator
54 =Lockable test button + LED (AC) +
mechanical indicator
74 =Lockable test button + double LED
(DC non-polarized) + mechanical indicator
B: Contact circuit
0 = CO (nPDT)
No. of poles
1 = 1 pole, 16 A
2 = 2 poles, 8 A
Coil version
9 = DC
8 = AC (50/60 Hz)
Coil voltage
See coil specifications
Selecting features and options: only combinations in the same row are possible.
Preferred selections for best availability are shown in bold.
Type
46.52
46.61
Coil version
AC - DC
AC
DC
AC - DC
AC
DC
A
0-5
0-5
0-5
0-4-5
0-4-5
0-4-5
B
0
0
0
0
0
0
C
2-4
54
74
2-4
54
74
D
0
/
/
0
/
/
Special versions for Rail Applications on request
Descriptions: Options
C: Option 74
LED (DC, non-polarized)
3
EUR
N
T E
T
The dual-purpose Finder test button can be used in two ways:
Case 1) The plastic pip (located directly below the test button) remains intact. In this case, when
the test button is pushed, the contacts operate. When the test button is released the contacts return
to their former state.
Case 2) The plastic pip is broken-off (using an appropriate cutting tool). In this case, (in addition
to the above function), when the test button is pushed and rotated, the contacts are latched in
the operating state, and remain so until the test button is rotated back to its former position.
In both cases ensure that the test button actuation is swift and decisive.
X-2013, www.findernet.com
1
P A
PEAN
EUR
Lockable test button and mechanical flag indicator (0040, 0054, 0074)
O
PEAN
2
O
C: Option 54
LED (AC)
2
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
46
SERIES
46 Series - Miniature industrial relays 8 - 16 A
Technical data
1 pole
2 pole
Nominal voltage of supply system
V AC
230/400
Rated insulation voltage
V AC
250
400
250
400
3
2
3
2
Pollution degree
230/400
Insulation between coil and contact set
Type of insulation
Reinforced (8 mm)
Overvoltage category
Rated impulse voltage
kV (1.2/50 µs)
Dielectric strength
V AC
Reinforced (8 mm)
III
III
6
6
4,000
4,000
Plug-in / PCB Relays
Insulation according to EN 61810-1
Insulation between adjacent contacts
Type of insulation
—
Basic
Overvoltage category
—
III
kV (1.2/50 µs)
—
4
V AC
—
2,000
Micro-disconnection
Micro-disconnection
1,000/1.5
1,000/1.5
Burst (5...50)ns, 5 kHz, on A1 - A2
EN 61000-4-4
level 4 (4 kV)
Surge (1.2/50 µs) on A1 - A2 (differential mode)
EN 61000-4-5
level 3 (2 kV)
Rated impulse voltage
Dielectric strength
Insulation between open contacts
Type of disconnection
Dielectric strength
V AC/kV (1.2/50 µs)
Conducted disturbance immunity
Other data
46.61
Bounce time: NO/NC
ms
46.52
2/6
1/4
Vibration resistance (10…150)Hz: NO/NC
g
20/12
20/15
Shock resistance
g
20
20
Power lost to the environment
without contact current
W
0.6
0.6
with rated current
W
1.6
2
mm
≥ 5
Recommended distance between relays mounted on PCB
Contact specification
Resistive load - cosϕ = 1
Inductive load - cosϕ = 0.4
F 46 - Electrical life (AC) v contact current
Type 46.61
Cycles
Cycles
F 46 - Electrical life (AC) v contact current
Type 46.52
Resistive load - cosϕ = 1
Inductive load - cosϕ = 0.4
DC breaking current (A)
X-2013, www.findernet.com
H 46 - Maximum DC1 breaking capacity
• When switching a resistive load (DC1) having voltage and current
values under the curve, an electrical life of ≥ 100·103 can be expected.
• In the case of DC13 loads, the connection of a diode in parallel with
the load will permit a similar electrical life as for a DC1 load.
Note: the release time for the load will be increased.
46.61 current limit
46.52 current limit
DC voltage (V)
3
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
46
SERIES
46 Series - Miniature industrial relays 8 - 16 A
Coil specifications
AC coil data
Plug-in / PCB Relays
DC coil data
Nominal
voltage
UN
V
12
24
48
110
125
Coil
code
9.012
9.024
9.048
9.110
9.125
Operating range
Umin
V
8.8
17.5
35
80
91.2
Resistance Rated coil
consumption
R
I at UN
Ω
mA
300
40
1,200
20
4,800
10
23,500
4.7
32,000
3.9
Umax
V
13.2
26.4
52.8
121
138
Nominal
voltage
UN
V
12
24
48
110
120
230
240
Coil
code
8.012
8.024
8.048
8.110
8.120
8.230
8.240
Operating range
Umin
V
9.6
19.2
38.4
88
96
184
192
Umax
V
13.2
26.4
52.8
121
132
253
264
Resistance Rated coil
consumption
R
I at UN
Ω
mA
80
90
320
45
1,350
21
6,900
9.4
9,000
8.4
28,000
5
31,500
4.1
R 46 - DC coil operating range v ambient temperature
R 46 - AC coil operating range v ambient temperature
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
Accessories
Flange mount adaptor for relays types 46.52 and 46.61
046.05
36.6
3.6
2
46
38
046.05
14.4
046.05 with relay
18.1
046.05
046.05 with relay
35 mm rail adaptor for relays types 46.52 and 46.61
046.07
42.4
39.8
14.4
046.07
046.07 with relay
Sheet of marker tags for relays types 46.52 and 46.61 (72 tags), 6x12mm
060.72
060.72
X-2013, www.findernet.com
35.4
46.9
046.07 with relay
34.8
046.07
4
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
46
SERIES
97 Series - Sockets and accessories for 46 series relays
97.01
Approvals
(according to type):
097.01
97.01 (blue)
46.61
97.01.0 (black) 97.02 (blue)
46.52
97.02.0 (black)
097.01
095.18 (blue)
097.71
095.00.4
095.18.0 (black)
99.02
86.30
Plug-in / PCB Relays
Screw terminal socket panel or 35 mm rail (EN 60715) mount
For relay type
Accessories
Plastic retain and release clip
(supplied with socket - packaging code SPA)
Metal retaining clip
Identification tag
8-way jumper link
Modules (see table below)
Timer modules (see table below)
Technical data
Rated current
Dielectric strength
Protection category
Ambient temperature
°C
Screw torque
Nm
Wire strip length
mm
Max. wire size for 97.01 and 97.02 sockets
mm2
AWG
16 A - 250 V AC
8 A - 250 V AC
6 kV (1.2/50 µs) between coil and contacts
IP 20
–40…+70 (see diagram L97)
0.8
8
solid wire
stranded wire
1x6 / 2x2.5
1x4 / 2x2.5
1x10 / 2x14
1x12 / 2x14
Rated current (A)
L 97 - Rated current vs ambient temperature
(for 46.61 relay / 97.01 socket combination)
P A
PEAN
N
T E
O
O
T
EUR
EUR
97.01
97.01
97.02
97.02
8-way jumper link for 97.01 and 97.02 sockets
095.18 (blue)
Rated values
10 A - 250 V
095.18.0 (black)
PEAN
095.18
86 series timer module
86.30
99.02
X-2013, www.findernet.com
Approvals
(according to type):
DC Modules with
non-standard polarity
(+A2) on request.
(12…24)V AC/DC; Bi-function: AI, DI; (0.05s…100h)
86.30.0.024.0000
(110...125)V AC; Bi-function: AI, DI; (0.05s…100h)
86.30.8.120.0000
(230...240)V AC; Bi-function: AI, DI; (0.05s…100h)
86.30.8.240.0000
Approvals
(according to type):
99.02 coil indication and EMC suppression modules for 97.01 and 97.02
Diode (+A1, standard polarity)
(6...220)V DC
LED
(6...24)V DC/AC
LED
(28...60)V DC/AC
LED
(110...240)V DC/AC
LED + Diode (+A1, standard polarity)
(6...24)V DC
LED + Diode (+A1, standard polarity)
(28...60)V DC
LED + Diode (+A1, standard polarity)
(110...220)V DC
LED + Varistor
(6...24)V DC/AC
LED + Varistor
(28...60)V DC/AC
LED + Varistor
(110...240)V DC/AC
RC circuit
(6...24)V DC/AC
RC circuit
(28...60)V DC/AC
RC circuit
(110...240)V DC/AC
Residual current by-pass
(110...240)V AC
sockets
99.02.3.000.00
99.02.0.024.59
99.02.0.060.59
99.02.0.230.59
99.02.9.024.99
99.02.9.060.99
99.02.9.220.99
99.02.0.024.98
99.02.0.060.98
99.02.0.230.98
99.02.0.024.09
99.02.0.060.09
99.02.0.230.09
99.02.8.230.07
5
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
46
SERIES
Plug-in / PCB Relays
97 Series - Sockets and accessories for 46 series relays
97.51
Approvals
(according to type):
097.01
Screwless terminal socket panel or 35 mm rail (EN 60715) mount 97.51 (blue)
For relay type
46.61
Accessories
Plastic retain and release clip
(supplied with socket - packaging code SPA)
Metal retaining clip
Modules (see table below)
Timer modules (see table below)
Technical data
Rated current
Dielectric strength
Protection category
Ambient temperature
Wire strip length
Max. wire size for 97.51 and 97.52 sockets
97.52.0 (black)
097.01
097.71
99.02
86.30
°C
mm
mm2
AWG
97.51
97.51.0 (black) 97.52 (blue)
46.52
97.51
10 A - 250 V AC
8 A - 250 V AC
6 kV (1.2/50 µs) between coil and contacts
IP 20
–25…+70
8
solid wire
stranded wire
2x(0.2...1.5)
2x(0.2...1.5)
2x(24...18)
2x(24...18)
97.52
97.52
86 series timer module
99.02
Approvals
(according to type):
DC Modules with
non-standard polarity
(+A2) on request.
86.30.0.024.0000
86.30.8.120.0000
(230...240)V AC; Bi-function: AI, DI; (0.05s…100h)
86.30.8.240.0000
Approvals (according to type):
99.02 coil indication and EMC suppression modules for 97.51 and 97.52
Diode (+A1, standard polarity)
(6...220)V DC
LED
(6...24)V DC/AC
LED
(28...60)V DC/AC
LED
(110...240)V DC/AC
LED + Diode (+A1, standard polarity)
(6...24)V DC
LED + Diode (+A1, standard polarity)
(28...60)V DC
LED + Diode (+A1, standard polarity)
(110...220)V DC
LED + Varistor
(6...24)V DC/AC
LED + Varistor
(28...60)V DC/AC
LED + Varistor
(110...240)V DC/AC
RC circuit
(6...24)V DC/AC
RC circuit
(28...60)V DC/AC
RC circuit
(110...240)V DC/AC
Residual current by-pass
(110...240)V AC
sockets
99.02.3.000.00
99.02.0.024.59
99.02.0.060.59
99.02.0.230.59
99.02.9.024.99
99.02.9.060.99
99.02.9.220.99
99.02.0.024.98
99.02.0.060.98
99.02.0.230.98
99.02.0.024.09
99.02.0.060.09
99.02.0.230.09
99.02.8.230.07
X-2013, www.findernet.com
86.30
(12…24)V AC/DC; Bi-function: AI, DI; (0.05s…100h)
(110...125)V AC; Bi-function: AI, DI; (0.05s…100h)
6
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
46
SERIES
97 Series - Sockets and accessories for 46 series relays
97.11
Approvals
(according to type):
97.11 (blue)
46.61
97.12 (blue)
46.52
12 A - 250 V (see diagram L97) 8 A - 250 V
6 kV (1.2/50 µs) between coil and contacts
IP 20
°C –40…+70
Rated current (A)
L 97 - Rated current vs ambient temperature
(for 46.61 relay / 97.11 socket combination)
Plug-in / PCB Relays
PCB socket
For relay type
Technical data
Rated values
Dielectric strength
Protection category
Ambient temperature
97.12
Approvals
(according to type):
97.11
97.12
Copper side view
Copper side view
Packaging codes
How to code and identify retaining clip and packaging options for sockets.
Example:
X-2013, www.findernet.com
9 7 . 0
1
S P
A
A
Standard packaging
SM Metal retaining clip
SP Plastic retaining clip
9 7 . 0
1
Without retaining clip
7
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
50
SERIES
50 Series - Forcibly guided contacts relay 8 A
50.12...1000
50.12...5000
PCB Relay with forcibly guided contacts
according to EN 50205 type B
2 CO contacts *
High physical separation between adjacent
contacts
• Cadmium Free contact materials
• 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts
• Flux proof: RT II
•
For medium duty switching,
suggested for DC loads
• 2 Pole 8 A
• 5 mm pinning
• PCB mounting
•
For safety applications
Gold plate contacts for
low level switching capability
• 5 mm pinning
• PCB mounting
•
Plug-in / PCB Relays
Features
•
*According to EN 50205 only 1 NO and 1 NC
(11-14 and 21-22 or 11-12 and 21-24) shall be
used as forcibly guided contacts.
FOR UL RATINGS SEE:
“General technical information” page V
Copper side view
Copper side view
2 CO (DPDT)
2 CO (DPDT)
Contact specification
Contact configuration
Rated current/Maximum peak current
A
Rated voltage/Maximum switching voltage V AC
8/15
8/15
250/400
250/400
Rated load AC1
VA
2,000
2,000
Rated load AC15 (230 V AC)
VA
500
500
Single phase motor rating (230 V AC)
kW
0.37
0.37
A
8/0.65/0.2
8/0.65/0.2
mW (V/mA)
500 (10/10)
50 (5/5)
AgNi
AgNi + Au
—
—
Breaking capacity DC1: 30/110/220 V
Minimum switching load
Standard contact material
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
V DC 5 - 6 - 12 - 24 - 48 - 60 - 110 - 125 5 - 6 - 12 - 24 - 48 - 60 - 110 - 125
Rated power AC/DC
Operating range
VA (50 Hz)/W
AC (50 Hz)
—/0.7
—/0.7
—
—
(0.75…1.2)UN
(0.75…1.2)UN
Holding voltage
AC/DC
—/0.4 UN
—/0.4 UN
Must drop-out voltage
AC/DC
—/0.1 UN
—/0.1 UN
Mechanical life AC/DC
cycles
—/10 · 106
—/10 · 106
Electrical life at rated load AC1
cycles
100 · 103
100 · 103
10/4
10/4
6 (8 mm)
6 (8 mm)
1,500
1,500
–40…+70
–40…+70
RT II
RT II
DC
Technical data
X-2013, www.findernet.com
Operate/release time
ms
Insulation between coil and contacts (1.2/50 µs) kV
Dielectric strength between open contacts
Ambient temperature range
Environmental protection
V AC
°C
Approvals (according to type)
1
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
50
SERIES
50 Series - Forcibly guided contacts relay 8 A
Ordering information
Plug-in / PCB Relays
Example: 50 series forcibly guided contacts, 2 CO (DPDT) 8 A contacts, 24 V DC coil.
A
5 0 . 1
2 . 9 . 0 2 4 . 5
Series
Type
1 = PCB - 5 mm pinning
A: Contact material
1 = Standard AgNi
5 = AgNi + Au
No. of poles
2 = 2 pole 8 A
B: Contact circuit
0 = CO (DPDT)
B
C
D
0
0
0
D: Special versions
0 = Flux proof (RT II)
C: Options
0 = None
Coil version
9 = DC
Coil voltage
See coil specifications
Selecting features and options: only combinations in the same row are possible.
Preferred selections for best availability are shown in bold.
Type
Coil version
A
B
C
D
50.12
DC
1-5
0
0
0
Technical data
Insulation according to EN 61810-1
Nominal voltage of supply system
V AC
230/400
Rated insulation voltage
V AC
250
400
3
2
Pollution degree
Insulation between coil and contact set
Type of insulation
Reinforced (8 mm)
Overvoltage category
III
Rated impulse voltage
kV (1.2/50 µs)
Dielectric strength
V AC
6
4,000
Insulation between adjacent contacts
Type of insulation
Basic
Overvoltage category
III
Rated impulse voltage
kV (1.2/50 µs)
Dielectric strength
V AC
4
3,000
Insulation between open contacts
Type of disconnection
Micro-disconnection
Dielectric strength
V AC/kV (1.2/50 µs)
1,500/2.5
Conducted disturbance immunity
Burst (5...50)ns, 5 kHz, on A1 - A2
EN 61000-4-4
level 4 (4 kV)
Surge (1.2/50 µs) on A1 - A2 (differential mode)
EN 61000-4-5
level 3 (2 kV)
Other data
Bounce time: NO/NC
ms
2/10
Vibration resistance (10…200)Hz: NO/NC
g
20/6
Shock resistance NO/NC
g
20/5
Power lost to the environment
without contact current
with rated current
0.7
W
1.2
mm
≥ 5
X-2013, www.findernet.com
Recommended distance between relays mounted on PCB
W
2
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
50
SERIES
50 Series - Forcibly guided contacts relay 8 A
Contact specification
DC breaking current (A)
Cycles
Resistive load - cosϕ = 1
Inductive load - cosϕ = 0.4
Plug-in / PCB Relays
H 50 - Maximum DC1 breaking capacity
F 50 - Electrical life (AC) v contact current
DC voltage (V)
• When switching a resistive load (DC1) having voltage and current
values under the curve, an electrical life of ≥ 100·103 can be expected.
• In the case of DC13 loads, the connection of a diode in parallel with
the load will permit a similar electrical life as for a DC1 load.
Note: the release time for the load will be increased.
Alternative selection of NO and NC
contacts to provide Forcibly guided
(mechanically linked) contacts, in
accordance with EN 50205 (type B).
Coil specifications
R 50 - DC coil operating range v ambient temperature
Standard coil
DC coil data
Nominal
voltage
UN
V
5
6
12
24
48
60
110
125
Coil
code
9.005
9.006
9.012
9.024
9.048
9.060
9.110
9.125
Operating range
Umin
V
3.8
4.5
9
18
36
45
82.5
93.7
Umax
V
6
7.2
14.4
28.8
57.6
72
131
150
Resistance Rated coil
consumption
R
I at UN
Ω
mA
35
143
50
120
205
58.5
820
29.3
3,280
14.4
5,140
11.7
17,250
6.4
22,300
5.6
X-2013, www.findernet.com
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
3
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
55
SERIES
55 Series - General purpose relays 7 - 10 A
Features
55.12
55.13
55.14
Plug-in / PCB Relays
Printed circuit mount, general purpose
2, 3 & 4 Pole relays
55.12 - 2 Pole 10 A
55.13 - 3 Pole 10 A
55.14 - 4 Pole 7 A
AC coils & DC coils
Cadmium Free contacts (preferred version)
• Contact material options
• RT III (wash tight) option available
•
•
•
•
55.12
55.13
2 pole, 10 A
PCB mount
•
•
3 pole, 10 A
PCB mount
•
•
4 pole, 7 A
PCB mount
55.14
FOR UL RATINGS SEE:
“General technical information” page V
Copper side view
Copper side view
Copper side view
2 CO (DPDT)
3 CO (3PDT)
4 CO (4PDT)
Contact specification
Contact configuration
Rated current/Maximum peak current
A
Rated voltage/Maximum switching voltage V AC
10/20
10/20
7/15
250/400
250/400
250/250
Rated load AC1
VA
2,500
2,500
1,750
Rated load AC15 (230 V AC)
VA
500
500
350
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1: 30/110/220V
Minimum switching load
A
mW (V/mA)
Standard contact material
0.37
0.37
0.125
10/0.25/0.12
10/0.25/0.12
7/0.25/0.12
300 (5/5)
300 (5/5)
300 (5/5)
AgNi
AgNi
AgNi
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240
V DC
Rated power AC/DC
VA (50 Hz)/W
Operating range
AC
6 - 12 - 24 - 48 - 60 - 110 -125 - 220
1.5/1
1.5/1
1.5/1
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
Holding voltage
AC/DC
0.8 UN/0.5 UN
0.8 UN/0.5 UN
0.8 UN/0.5 UN
Must drop-out voltage
AC/DC
0.2 UN/0.1 UN
0.2 UN/0.1 UN
0.2 UN/0.1 UN
20 · 106/50 · 106
20 · 106/50 · 106
20 · 106/50 · 106
DC
Technical data
Mechanical life AC/DC
Electrical life at rated load AC1
X-2013, www.findernet.com
Operate/release time
cycles
cycles
ms
Insulation between coil and contacts (1.2/50 µs) kV
Dielectric strength between open contacts V AC
Ambient temperature range
Environmental protection
°C
3
200 · 10
3
200 · 10
150 · 103
10/5
10/5
11/3
4
4
4
1,000
1,000
1,000
–40…+85
–40…+85
–40…+85
RT I
RT I
RT I
Approvals (according to type)
1
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
55
SERIES
55 Series - General purpose relays 7 - 10 A
Plug-in / PCB Relays
Features
55.32
55.33
55.34
Plug-in mount, general purpose
2, 3 & 4 Pole relays
55.32 - 2 Pole 10 A
55.33 - 3 Pole 10 A
55.34 - 4 Pole 7 A
Lockable test button and mechanical flag
indicator as standard on 2 & 4 pole types
• AC coils & DC coils
• UL Listing (certain relay/socket combinations)
• Cadmium Free contacts (preferred version)
• Contact material options
• 94 series sockets
• Coil EMC suppression
• Timer accessories 86 series
• European Patent
•
55.32
55.33
•
•
2 pole, 10 A
Plug-in 94 series sockets
•
•
3 pole, 10 A
Plug-in 94 series sockets
•
•
4 pole, 7 A
Plug-in 94 series sockets
55.34
FOR UL RATINGS SEE:
“General technical information” page V
Contact specification
2 CO (DPDT)
Contact configuration
Rated current/Maximum peak current
A
Rated voltage/Maximum switching voltage V AC
3 CO (3PDT)
4 CO (4PDT)
10/20
10/20
7/15
250/400
250/400
250/250
Rated load AC1
VA
2,500
2,500
1,750
Rated load AC15 (230 V AC)
VA
500
500
350
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
Standard contact material
0.37
0.37
0.125
10/0.25/0.12
10/0.25/0.12
7/0.25/0.12
300 (5/5)
300 (5/5)
300 (5/5)
AgNi
AgNi
AgNi
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240
V DC
Rated power AC/DC
VA (50 Hz)/W
Operating range
AC
6 - 12 - 24 - 48 - 60 - 110 - 125 - 220
1.5/1
1.5/1
1.5/1
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
Holding voltage
AC/DC
0.8 UN/0.5 UN
0.8 UN/0.5 UN
0.8 UN/0.5 UN
Must drop-out voltage
AC/DC
0.2 UN/0.1 UN
0.2 UN/0.1 UN
0.2 UN/0.1 UN
20 · 106/50 · 106
20 · 106/50 · 106
20 · 106/50 · 106
DC
Mechanical life AC/DC
Electrical life at rated load AC1
Operate/release time
cycles
cycles
ms
Insulation between coil and contacts (1.2/50 µs) kV
Dielectric strength between open contacts V AC
Ambient temperature range
Environmental protection
Approvals (according to type)
°C
3
3
200 · 10
200 · 10
150 · 103
10/5
10/5
11/3
4
4
4
1,000
1,000
1,000
–40…+85
–40…+85
–40…+85
RT I
RT I
RT I
X-2013, www.findernet.com
Technical data
2
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
55
SERIES
55 Series - General purpose relays 7 - 10 A
Ordering information
5 5 . 3
A
B
C
D
4 . 9 . 0 1 2 . 0
0
4
0
Series
Type
1 = PCB
3 = Plug-in
No. of poles
2 = 2 pole, 10 A
3 = 3 pole, 10 A
4 = 4 pole, 7 A
A: Contact material
0 = Standard AgNi
2 = AgCdO
5 = AgNi + Au
D: Special versions
0 = Standard
1 = Wash tight (RT III)
for 55.12, 55.13 and 55.14 only
B: Contact circuit
0 = CO (nPDT)
C: Options
0 = None
1 = Lockable test button
2 = Mechanical indicator
3 = LED (AC)
4 = Lockable test button+mechanical indicator
5 = Lockable test button + LED (AC)
54 = Lockable test button + LED (AC)
+ mechanical indicator
6* = Double LED (DC non-polarized)
7* = Lockable test button + double LED
(DC non-polarized)
74* = Lockable test button + double LED
(DC non-polarized)
+ mechanical indicator
8* = LED + diode
(DC, polarity positive to pin A1/13)
9* = Lockable test button + LED + diode (DC,
polarity positive to pin A1/13)
94* = Lockable test button + LED + diode (DC,
polarity positive to pin A1/13)
+ mechanical indicator
* Option not available for the 220 V DC version.
Coil version
8 = AC (50/60 Hz)
9 = DC
Coil voltage
See coil specifications
Selecting features and options: only combinations in the same row are possible.
Preferred selections for best availability are shown in bold.
Type
Coil version
55.32/34 AC-DC
AC
AC
DC
DC
55.33
AC-DC
AC
DC
55.12/13/14 AC-DC
A
0-2-5
0-2-5
0-2-5
0-2-5
0-2-5
0-2-5
0-2-5
0-2-5
0-2-5
B
0
0
0
0
0
0
0
0
0
Plug-in / PCB Relays
Example: 55 series plug-in relay, 4 CO (4PDT), 12 V DC coil, lockable test button and mechanical indicator.
C
0
2-3-4-5
54
2-4 -6 -7-8-9
74 - 94
0
1-3-5
1-6-7-8-9
0
D
0
0
/
0
/
0
0
0
0-1
Descriptions: options and special versions
2
EUR
Lockable test button and mechanical flag indicator
(0010, 0040, 0050, 0054, 0070, 0074, 0090, 0094)
O
P A
PEAN
N
T E
T
EUR
3
1
X-2013, www.findernet.com
C: Option 8, 9, 94
LED + diode (DC, polarity
positive to pin A1/13)
PEAN
C: Option 6, 7, 74
Double LED
(DC non-polarized)
O
C: Option 3, 5, 54
LED (AC)
The dual-purpose Finder test button can be used in two ways:
Case 1) The plastic pip (located directly above the test button) remains intact. In this case, when the
test button is pushed, the contacts operate. When the test button is released the contacts return to their
former state.
Case 2) The plastic pip is broken-off (using an appropriate cutting tool). In this case, (in addition to
the above function), when the test button is pushed and rotated, the contacts are latched in the
operating state, and remain so until the test button is rotated back to its former position.
In both cases ensure that the test button actuation is swift and decisive.
3
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
55
SERIES
55 Series - General purpose relays 7 - 10 A
Technical data
Plug-in / PCB Relays
Insulation according to EN 61810-1
2 pole - 3 pole
Nominal voltage of supply system
V AC 230/400
Rated insulation voltage
V AC 400
Pollution degree
4 pole
230
250
2
2
Insulation between coil and contact set
Type of Insulation
Basic
Basic
Overvoltage category
III
III
Rated impulse voltage
kV (1.2/50 µs) 4
4
Dielectric strength
V AC 2,000
2,000
Insulation between adjacent contacts
Type of insulation
Basic
Basic
Overvoltage category
III
II
Rated impulse voltage
kV (1.2/50 µs) 4
Dielectric strength
2.5
V AC 2,000
2,000
Insulation between open contacts
Type of disconnection
Micro-disconnection
Dielectric strength
Micro-disconnection
V AC/kV (1.2/50 µs) 1,000/1.5
1,000/1.5
Conducted disturbance immunity
Burst (5...50)ns, 5 kHz, on A1 - A2
EN 61000-4-4
level 4 (4 kV)
Surge (1.2/50 µs) on A1 - A2 (differential mode)
EN 61000-4-5
level 4 (4 kV)
Other data
Bounce time: NO/NC
ms 1/3
Vibration resistance (5…55)Hz: NO/NC
g 15/15
Shock resistance
g 16
Power lost to the environment
without contact current
with rated current
Recommended distance between relays mounted on PCB
W 1
W 3 (2 pole)
4 (3 pole)
3 (4 pole)
mm ≥ 5
Contact specification
Cycles
Resistive load - cosϕ = 1
Inductive load - cosϕ = 0.4
Cycles
F 55 - Electrical life (AC) v contact current
4 pole relay
F 55 - Electrical life (AC) v contact current
2 and 3 pole relays
Resistive load - cosϕ = 1
Inductive load - cosϕ = 0.4
2 & 3 pole current limit
4 pole current limit
contacts in series
DC voltage (V)
• When switching a resistive load (DC1) having voltage and current
values under the curve, an electrical life of ≥ 100·103 can be expected.
• In the case of DC13 loads, the connection of a diode in parallel with
the load will permit a similar electrical life as for a DC1 load.
Note: the release time for the load will be increased.
X-2013, www.findernet.com
DC breaking current (A)
H 55 - Maximum DC1 breaking capacity
4
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
55
SERIES
55 Series - General purpose relays 7 - 10 A
Coil specifications
Nominal
voltage
UN
V
6
12
24
48
60
110
125
220
AC coil data
Coil
code
Operating range
9.006
9.012
9.024
9.048
9.060
9.110
9.125
9.220
Umin
V
4.8
9.6
19.2
38.4
48
88
100
176
Umax
V
6.6
13.2
26.4
52.8
66
121
138
242
Resistance Rated coil
consumption
R
I at UN
Ω
mA
40
150
140
86
600
40
2,400
20
4,000
15
12,500
8.8
17,300
7.2
54,000
4
Nominal
voltage
UN
V
6
12
24
48
60
110
120
230
240
Coil
code
8.006
8.012
8.024
8.048
8.060
8.110
8.120
8.230
8.240
Operating range
Umin
V
4.8
9.6
19.2
38.4
48
88
96
184
192
Umax
V
6.6
13.2
26.4
52.8
66
121
132
253
264
Resistance Rated coil
consumption
R
I at UN (50Hz)
Ω
mA
12
200
50
97
190
53
770
25
1,200
21
4,000
12.5
4,700
12
17,000
6
19,100
5.3
R 55 - DC coil operating range v ambient temperature
R 55 - AC coil operating range v ambient temperature
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
Plug-in / PCB Relays
DC coil data
Accessories
Top flange mount adaptor for 55.32, 55.33, 55.34
056.25
056.25 with relay
056.25
056.27
Rear flange mount
adaptor for 55.32, 55.33, 55.34
056.26
056.25
056.25 with relay
056.27 with 056.26
relay
056.26 with relay
056.26
X-2013, www.findernet.com
Top 35 mm rail (EN 60715) adaptor for 55.32, 55.33, 55.34
056.27
056.26 with relay
056.27
056.27 with relay
056.27
056.27 with relay
5
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
55
SERIES
Plug-in / PCB Relays
94 Series - Socket overview for 55 series relays
Module Socket
99.02 94.02
94.03
94.04
Relay
55.32
55.33
55.32
55.34
Module Socket
99.02 94.54
Relay Description
55.32 Screwless terminal socket
55.34 - For fast cable connections
- Top terminals - Contacts
- Bottom terminals - Coil
Module Socket
99.01 94.72
94.73
94.74
Relay Description
Mounting
55.32 Screw terminal (Plate clamp) socket Panel or 35 mm rail
55.33
(EN 60715) mount
55.32
55.34
Accessories
- Coil indication and EMC
suppression modules
- Metal retaining clip
Module Socket
99.01 94.82
Relay Description
Mounting
55.32 Screw terminal (Plate clamp) socket Panel or 35 mm rail
- 23 mm wide for space saving
(EN 60715) mount
Accessories
- Coil indication and EMC
suppression modules
- Metal retaining clip
94.04
Description
Screw terminal (Box clamp) socket
- Top terminals - Contacts
- Bottom terminals - Coil
Mounting
Panel or 35 mm rail
(EN 60715) mount
Accessories
- Coil indication and EMC
suppression modules
- Jumper link
- Timer modules
- Plastic retaining and release
clip
Mounting
Panel or 35 mm rail
(EN 60715) mount
Accessories
- Coil indication and EMC
suppression modules
- Jumper link
- Timer modules
- Plastic retaining and release
clip
See page 7
See page 8
94.54
94.74
See page 9
94.82
See page 9
94.84.3
Module Socket Relay Description
99.80 94.84.2 55.32 Screw terminal (Box clamp) socket
55.34
94.82.3 55.32
94.84.3 55.32
55.34
Mounting
Panel or 35 mm rail
(EN 60715) mount
Accessories
- Coil indication and EMC
suppression modules
- Jumper link
- Plastic retainig and release
clip
Module Socket Relay
99.80 94.92.3 55.32
94.94.3 55.32
55.34
Mounting
Panel or 35 mm rail
(EN 60715) mount
Accessories
- Coil indication and EMC
suppression modules
- Jumper link
- Plastic retaining and release
clip
See page 10
Description
Screw terminal (Box clamp) socket
- Top terminals - Contacts
- Bottom terminals - Coil
94.94.3
94.14
See page 12
94.22
See page 12
94.34
See page 13
Module
—
—
—
Socket
94.12
94.13
94.14
Relay Description
55.32 PCB sockets
55.33
55.32
55.34
Mounting
PCB mounting
Accessories
- Metal retaining clip
Module
—
—
—
Socket
94.22
94.23
94.24
Relay Description
55.32 Panel mount
55.33 with solder connections
55.32
55.34
Mounting
Panel mount on 1 mm
thick panel
Accessories
- Metal retaining clip
Module
—
—
—
Socket
94.32
94.33
94.34
Relay Description
55.32 Panel mount
55.33 with solder connections
55.32
55.34
Mounting
M3 screw fixing
Accessories
- Metal retaining clip
X-2013, www.findernet.com
See page 11
6
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
55
SERIES
Screw terminal (Box clamp) socket panel or 35 mm
(EN 60715) rail mount
For relay type
Accessories
Metal retaining clip
94.04
Plastic retaining and release clip
Approvals
(supplied
with socket - packaging code SPA)
(according to type):
6-way jumper link
Identification tag
Modules (see table below)
Timer modules (see table below)
Certain relay/socket Sheet of marker tags for retaining and release clip 094.91.3
combinations
plastic, 72 tags, 6x12 mm
Technical data
Rated values
Dielectric strength
Protection category
Ambient temperature
°C
094.91.3
Screw torque
Nm
Wire strip length
mm
Max. wire size for 94.02/03/04 sockets
mm2
AWG
94.02
Blue
55.32
94.02.0 94.03
Black
Blue
55.33
94.03.0 94.04
94.04.0
Black
Blue
Black
55.32, 55.34
094.71
094.91.3 094.91.30 094.91.3 094.91.30 094.91.3 094.91.30
094.06
094.06.0 094.06 094.06.0 094.06
094.00.4
99.02
86.30
060.72
10 A - 250 V
2 kV AC
IP 20
–40…+70
0.5
8
solid wire
1x6 / 2x2.5
1x10 / 2x14
094.06.0
Plug-in / PCB Relays
94 Series - Sockets and accessories for 55 series relays
stranded wire
1x4 / 2x2.5
1x12 / 2x14
Top
terminals
060.72
P A
PEAN
N
T E
O
O
T
EUR
EUR
94.04
Bottom
terminals
6-way jumper link for 94.02, 94.03 and 94.04 sockets
094.06 (blue)
Rated values
10 A - 250 V
86 series timer modules
(12…24)V AC/DC; Bi-function: AI, DI; (0.05s…100h)
86.30.0.024.0000
094.06.0 (black)
PEAN
094.06
86.30
99.02
X-2013, www.findernet.com
Approvals
(according to type):
DC Modules with
non-standard polarity
(+A2) on request.
(110...125)V AC; Bi-function: AI, DI; (0.05s…100h)
(230...240)V AC; Bi-function: AI, DI; (0.05s…100h)
Approvals
(according to type):
86.30.8.120.0000
86.30.8.240.0000
99.02 coil indication and EMC suppression modules for 94.02, 94.03 and
Diode (+A1, standard polarity)
(6...220)V DC
LED
(6...24)V DC/AC
LED
(28...60)V DC/AC
LED
(110...240)V DC/AC
LED + Diode (+A1, standard polarity)
(6...24)V DC
LED + Diode (+A1, standard polarity)
(28...60)V DC
LED + Diode (+A1, standard polarity)
(110...220)V DC
LED + Varistor
(6...24)V DC/AC
LED + Varistor
(28...60)V DC/AC
LED + Varistor
(110...240)V DC/AC
RC circuit
(6...24)V DC/AC
RC circuit
(28...60)V DC/AC
RC circuit
(110...240)V DC/AC
Residual current by-pass
(110...240)V AC
94.04 sockets
99.02.3.000.00
99.02.0.024.59
99.02.0.060.59
99.02.0.230.59
99.02.9.024.99
99.02.9.060.99
99.02.9.220.99
99.02.0.024.98
99.02.0.060.98
99.02.0.230.98
99.02.0.024.09
99.02.0.060.09
99.02.0.230.09
99.02.8.230.07
7
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
55
SERIES
Plug-in / PCB Relays
94 Series - Sockets and accessories for 55 series relays
Screwless terminal socket 35 mm rail (EN 60715) mount
For relay type
Accessories
Metal retaining clip
Plastic retaining and release clip
6-way jumper link
Modules (see table below)
Sheet of marker tags, 72 tags, 6x12 mm
Technical data
Rated values
Dielectric strength
Protection category
Ambient temperature
°C
Wire strip length
mm
Max. wire size for 94.54 socket
mm2
AWG
94.54
Approvals
(according to type):
094.91.3
94.54 (blue)
55.32, 55.34
094.71
094.91.3
094.56
99.02, 86.30
060.72
10 A - 250 V
2 kV AC
IP 20
–25…+70
10
solid wire
2x(0.2…1.5)
2x(24…14)
stranded wire
2x(0.2…1.5)
2x(24…14)
Top
terminals
060.72
Sockets +
jumper link
P A
PEAN
N
T E
O
O
T
EUR
EUR
Bottom
terminals
6-way jumper link
094.56 (blue)
Rated values
10 A - 250 V
PEAN
094.56
86 series timer modules
99.02
Approvals
(according to type):
DC Modules with
non-standard polarity
(+A2) on request.
86.30.0.024.0000
(110...125)V AC; Bi-function: AI, DI; (0.05s…100h)
86.30.8.120.0000
(230...240)V AC; Bi-function: AI, DI; (0.05s…100h)
86.30.8.240.0000
Approvals
(according to type):
99.02 coil indication and EMC suppression modules for 94.54 sockets
Diode (+A1, standard polarity)
(6...220)V DC
LED
(6...24)V DC/AC
LED
(28...60)V DC/AC
LED
(110...240)V DC/AC
LED + Diode (+A1, standard polarity)
(6...24)V DC
LED + Diode (+A1, standard polarity)
(28...60)V DC
LED + Diode (+A1, standard polarity)
(110...220)V DC
LED + Varistor
(6...24)V DC/AC
LED + Varistor
(28...60)V DC/AC
LED + Varistor
(110...240)V DC/AC
RC circuit
(6...24)V DC/AC
RC circuit
(28...60)V DC/AC
RC circuit
(110...240)V DC/AC
Residual current by-pass
(110...240)V AC
99.02.3.000.00
99.02.0.024.59
99.02.0.060.59
99.02.0.230.59
99.02.9.024.99
99.02.9.060.99
99.02.9.220.99
99.02.0.024.98
99.02.0.060.98
99.02.0.230.98
99.02.0.024.09
99.02.0.060.09
99.02.0.230.09
99.02.8.230.07
X-2013, www.findernet.com
86.30
(12…24)V AC/DC; Bi-function: AI, DI; (0.05s…100h)
8
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
55
SERIES
94.74
Approvals
(according to type):
94.82
Approvals
(according to type):
Screw terminal (Plate clamp) socket panel or 35 mm
(EN 60715) rail mount
For relay type
Accessories
Metal retaining clip (supplied with socket - packaging code SMA)
Modules (see table below)
Screw terminal (Plate clamp) socket: panel or 35 mm rail mount
For relay type
Accessories
Metal retaining clip (supplied with socket - packaging code SMA)
Modules (see table below)
Technical data
Rated values
Dielectric strength
Protection category
Ambient temperature
°C
Screw torque
Nm
Wire strip length
mm
Max. wire size for 94.72/73/74 and 94.82 sockets
mm2
AWG
94.72
94.72
Blue
55.32
94.72.0 94.73
Black
Blue
55.33
94.82 (blue)
55.32
94.73.0 94.74
94.74.0
Black
Blue
Black
55.32, 55.34
094.71
99.01
94.82.0 (black)
55.32
094.71
99.01
10 A - 250 V
2 kV AC
IP 20
–40…+70
0.5
8 (94.72/73/74)
solid wire
1x2.5 / 2x1.5
1x14 / 2x16
Plug-in / PCB Relays
94 Series - Sockets and accessories for 55 series relays
9 (94.82)
stranded wire
1x2.5 / 2x1.5
1x14 / 2x16
94.73
94.74
Top
terminals
Bottom
terminals
94.82
99.01
X-2013, www.findernet.com
Approvals
(according to type):
* Modules in Black
housing are
available on request.
Green LED is standard.
Red LED available on
request.
99.01 coil indication and EMC suppression modules for 94.72, 94.73, 94.74 and 94.82 sockets
Blue*
Diode (+A1, standard polarity)
(6...220)V DC 99.01.3.000.00
Diode (+A2, non standard polarity)
(6...220)V DC 99.01.2.000.00
LED
(6...24)V DC/AC 99.01.0.024.59
LED
(28...60)V DC/AC 99.01.0.060.59
LED
(110...240)V DC/AC 99.01.0.230.59
LED + Diode (+A1, standard polarity)
(6...24)V DC 99.01.9.024.99
LED + Diode (+A1, standard polarity)
(28...60)V DC 99.01.9.060.99
LED + Diode (+A1, standard polarity)
(110...220)V DC 99.01.9.220.99
LED + Diode (+A2, non standard polarity)
(6...24)V DC 99.01.9.024.79
LED + Diode (+A2, non standard polarity)
(28...60)V DC 99.01.9.060.79
LED + Diode (+A2, non standard polarity)
(110...220)V DC 99.01.9.220.79
LED + Varistor
(6...24)V DC/AC 99.01.0.024.98
LED + Varistor
(28...60)V DC/AC 99.01.0.060.98
LED + Varistor
(110...240)V DC/AC 99.01.0.230.98
RC circuit
(6...24)V DC/AC 99.01.0.024.09
RC circuit
(28...60)V DC/AC 99.01.0.060.09
RC circuit
(110...240)V DC/AC 99.01.0.230.09
Residual current by-pass
(110...240)V AC 99.01.8.230.07
9
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
55
SERIES
Plug-in / PCB Relays
94 Series - Sockets and accessories for 55 series relays
94.84.3
Approvals
(according to type):
94.84.2
Approvals
(according to type):
094.91.3
Screw terminal (Box clamp) socket panel or 35 mm
(EN 60715) rail mount
For relay type
Accessories
Metal retaining clip (supplied with socket - packaging code SMA)
Plastic retaining and release clip
6-way jumper link
Identification tag
Modules (see table next page)
Sheet of marker tags for retaining and release clip 094.91.3
plastic, 72 tags, 6x12 mm
Screw terminal (Box clamp) socket panel or 35 mm
(EN 60715) rail mount
For relay type
Accessories
Metal retaining clip (supplied with socket - packaging code SMA)
Plastic retaining and release clip
6-way jumper link
Identification tag
Modules (see table next page)
Sheet of marker tags for retaining and release clip 094.91.3
plastic, 72 tags, 6x12 mm
Technical data
Rated values
Dielectric strength
Protection category
Ambient temperature
°C
Screw torque
Nm
Wire strip length
mm
Max. wire size for 94.82.3, 94.84.3 and
94.84.2 sockets
mm2
AWG
94.82.3
Blue
55.32
094.91.3
094.06
94.84.2
Blue
55.32, 55.34
094.91.3
094.06
10 A - 250 V
2 kV AC
IP 20
–40…+70
0.5
7
solid wire
1x6 / 2x2.5
1x10 / 2x14
94.82.30
Black
94.84.3
94.84.30
Blue
Black
55.32, 55.34
094.71
094.91.30
094.91.3
094.06.0
094.06
094.80.3
99.80
060.72
094.91.30
094.06.0
94.84.20
Black
094.71
094.91.30
094.06.0
094.80.3
99.80
060.72
stranded wire
1x4 / 2x2.5
1x12 / 2x14
060.72
Top terminals
Bottom terminals
94.84.3
94.84.2
Bottom terminals
94.84.2
X-2013, www.findernet.com
Top terminals
10
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
55
SERIES
94 Series - Sockets and accessories for 55 series relays
94.94.3
Approvals
(according to type):
094.91.3
060.72
94.92.3 (blue) 94.92.30 (black) 94.94.3 (blue) 94.94.30 (black)
55.32
55.32, 55.34
094.91.3
094.06
094.71
094.91.30
094.91.3
094.06.0
094.06
094.80.3
99.80
060.72
10 A - 250 V
2 kV AC
IP 20
–25…+70
0.5
8
solid wire
1x6 / 2x2.5
1x10 / 2x14
094.91.30
094.06.0
Plug-in / PCB Relays
Screw terminal (Box clamp) socket panel or 35 mm rail mount
For relay type
Accessories
Metal retaining clip
Plastic retaining and release clip
6-way jumper link
Identification tag
Modules (see table below page)
Sheet of marker tags for retaining and release clip 094.91.3
plastic, 72 tags, 6x12 mm
Technical data
Rated values
Dielectric strength
Protection category
Ambient temperature
°C
Screw torque
Nm
Wire strip length
mm
Max. wire size for 94.92.3 and 94.94.3 sockets
mm2
AWG
stranded wire
1x4 / 2x2.5
1x12 / 2x14
Top terminals
P A
PEAN
N
T E
O
O
T
EUR
EUR
Bottom terminals
94.94.3
6-way jumper link for 94.84.2, 94.82.3, 94.84.3, 94.92.3 and 94.94.3 sockets 094.06 (blue)
Rated values
094.06.0 (black)
10 A - 250 V
PEAN
094.06
99.80
X-2013, www.findernet.com
Approvals
(according to type):
* Modules in Black
housing are
available on request.
Green LED is standard.
Red LED available
on request.
99.80 coil indication and EMC suppression modules for 94.84.2, 94.82.3, 94.84.3, 94.92.3 and 94.94.3 sockets
Blue*
Diode (+A1, standard polarity)
(6...220)V DC
99.80.3.000.00
LED
(6...24)V DC/AC
99.80.0.024.59
LED
(28...60)V DC/AC
99.80.0.060.59
LED
(110...240)V DC/AC
99.80.0.230.59
LED + Diode (+A1, standard polarity)
(6...24)V DC
99.80.9.024.99
LED + Diode (+A1, standard polarity)
(28...60)V DC
99.80.9.060.99
LED + Diode (+A1, standard polarity)
(110...220)V DC
99.80.9.220.99
LED + Varistor
(6...24)V DC/AC
99.80.0.024.98
LED + Varistor
(28...60)V DC/AC
99.80.0.060.98
LED + Varistor
(110...240)V DC/AC
99.80.0.230.98
RC circuit
(6...24)V DC/AC
99.80.0.024.09
RC circuit
(28...60)V DC/AC
99.80.0.060.09
RC circuit
(110...240)V DC/AC
99.80.0.230.09
Residual current by-pass
(110...240)V AC
99.80.8.230.07
11
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
55
SERIES
94 Series - Sockets and accessories for 55 series relays
Plug-in / PCB Relays
PCB socket
94.14
Approvals
(according to type):
94.12
Blue
55.32
94.12.0 94.13
Black
Blue
55.33
For relay type
Accessories
Metal retaining clip (supplied with socket - packaging code SMA)
Technical data
Rated values
10 A - 250 V
Dielectric strength
2 kV AC
Ambient temperature
°C –40…+70
94.13.0 94.14
94.14.0
Black
Blue
Black
55.32, 55.34
094.51
Copper side view
94.12
Panel mount solder socket 1 mm thick panel
94.22
94.22
Blue
55.32
94.14
94.22.0 94.23
Black
Blue
55.33
For relay type
Accessories
Metal retaining clip (supplied with socket - packaging code SMA)
Technical data
Rated values
10 A - 250 V
Dielectric strength
2 kV AC
Ambient temperature
°C –40…+70
94.23.0 94.24
94.24.0
Black
Blue
Black
55.32, 55.34
094.51
X-2013, www.findernet.com
Approvals
(according to type):
94.13
12
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
55
SERIES
Panel mount socket M3 screw fixing - solder connections
94.34
Approvals
(according to type):
For relay type
Accessories
Metal retaining clip (supplied with socket - packaging code SMA)
Technical data
Rated values
Dielectric strength
Ambient temperature
°C
94.32
Blue
55.32
94.32.0 94.33
Black
Blue
55.33
94.33.0 94.34
94.34.0
Black
Blue
Black
55.32, 55.34
094.51
10 A - 250 V
2 kV AC
–40…+70
Plug-in / PCB Relays
94 Series - Sockets and accessories for 55 series relays
Packaging codes
How to code and identify retaining clip and packaging options for sockets.
Example:
9 4 . 0
4
S P
A
A
Standard packaging
SM Metal retaining clip
SP Plastic retaining clip
4
Without retaining clip
X-2013, www.findernet.com
9 4 . 0
13
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
56
SERIES
56 Series - Miniature power relays 12 A
Features
56.32/56.34
56.32-0300/56.34-0300
Plug-in - 12 A Power relay, 2 & 4 pole
Flange mount option (Faston 187, 4.8x0.5 mm termination)
• AC coils & DC coils
• Lockable test button and mechanical flag indicator
• Cadmium Free contacts (standard version)
• Contact material options
• 96 series sockets
• Coil EMC suppression
• Accessories
• European Patent
•
•
•
56.32
2 or 4 pole normally open contact
(≥1.5 mm gap)
• Plug-in/Faston 187
•
2 or 4 pole changeover contact
Plug-in/Faston 187
56.32-0300
56.34-0300
56.34
* For 4 CO (4PDT) or 4 NO only.
FOR UL RATINGS SEE:
“General technical information” page V
56.32
56.34
56.32-0300
56.34-0300
Contact specification
2 CO (DPDT)
Contact configuration
Rated current/Maximum peak current
A
Rated voltage/Maximum switching voltage V AC
4 CO (4PDT)
2NO (DPST-NO) - ≥1.5mm gap 4NO (4PST-NO) - ≥1.5mm gap
12/20
12/20
250/400
250/400
Rated load AC1
VA
3,000
3,000
Rated load AC15 (230 V AC)
VA
700
700
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
0.55
0.55
12/0.5/0.25
12/1/0.5
500 (10/5)
500 (10/5)
AgNi
AgNi
Standard contact material
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
V DC
Rated power AC/DC
VA (50 Hz)/W
Operating range
6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400*
6 - 12 - 24 - 48 - 60 - 110 - 125 - 220
1.5/1
AC
DC
2/1.3
—
1.5/—
(0.8…1.1)UN
2/—
(0.85…1.1)UN
(0.8…1.1)UN
(0.85…1.1)UN
—
Holding voltage
AC/DC
0.8 UN/0.6 UN
0.85 UN/—
Must drop-out voltage
AC/DC
0.2 UN/0.1 UN
0.2 UN/—
VIII-2013, www.findernet.com
Technical data
Mechanical life AC/DC
cycles
20 · 106/50 · 106
20 · 106/—
Electrical life at rated load AC1
cycles
100 · 103
100 · 103
Operate/release time
ms
Insulation between coil and contacts (1.2/50 µs) kV
Dielectric strength between open contacts
Ambient temperature range
Environmental protection
V AC
°C
8/3
10/4
4
5
8/4
4
5
1,000
2,000
–40…+70
–40…+70
RT I
RT I
Approvals (according to type)
1
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
56
SERIES
56 Series - Miniature power relays 12 A
Features
56.42/56.44
56.42-0300/56.44-0300
Printed circuit mount
12 A Power relay
2 & 4 pole
AC coils & DC coils
• Cadmium Free contacts (standard version)
• Contact material option
• RT III (wash tight) option available
•
•
•
•
56.42
2 or 4 pole normally open contact
(≥ 1.5 mm gap)
• PCB mount
•
2 or 4 pole changeover contact
PCB mount
56.42-0300
56.44
56.44-0300
56.42
Copper side view
* For 4 CO (4PDT) or 4 NO only.
FOR UL RATINGS SEE:
“General technical information” page V
56.44
Copper side view
56.42-0300
Copper side view
56.44-0300
Copper side view
Contact specification
2 CO (DPDT)
Contact configuration
Rated current/Maximum peak current
4 CO (4PDT)
12/20
12/20
250/400
250/400
A
Rated voltage/Maximum switching voltage V AC
2NO (DPST-NO) - ≥1.5mm gap 4NO (4PST-NO) - ≥1.5mm gap
Rated load AC1
VA
3,000
3,000
Rated load AC15 (230 V AC)
VA
700
700
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
0.55
0.55
12/0.5/0.25
12/1/0.5
500 (10/5)
500 (10/5)
AgNi
AgNi
Standard contact material
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
V DC
Rated power AC/DC
VA (50 Hz)/W
Operating range
6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400*
6 - 12 - 24 - 48 - 60 - 110 - 125 - 220
1.5/1
AC
DC
2/1.3
—
1.5/—
(0.8…1.1)UN
2/—
(0.85…1.1)UN
(0.8…1.1)UN
(0.85…1.1)UN
—
Holding voltage
AC/DC
0.8 UN/0.6 UN
0.85 UN/—
Must drop-out voltage
AC/DC
0.2 UN/0.1 UN
0.2 UN/—
Mechanical life AC/DC
cycles
20 · 106/50 · 106
20 · 106/—
Electrical life at rated load AC1
cycles
100 · 103
100 · 103
Operate/release time
ms
Insulation between coil and contacts (1.2/50 µs) kV
Dielectric strength between open contacts
Ambient temperature range
Environmental protection
Approvals (according to type)
V AC
°C
8/3
10/4
4
5
8/4
4
5
1,000
2,000
–40…+70
–40…+70
RT I
RT I
VIII-2013, www.findernet.com
Technical data
2
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
56
SERIES
56 Series - Miniature power relays 12 A
Ordering information
Example: 56 series plug-in relay, 2 CO (DPDT), 12 V DC coil, lockable test button and mechanical indicator.
5 6 . 3
A
B
C
D
2 . 9 . 0 1 2 . 0
0
4
0
A: Contact material
0 = Standard AgNi
2 = AgCdO
4 = AgSnO2
Series
Type
3 = Plug-in
4 = PCB
B: Contact circuit
0 = CO (nPDT)
3 = NO (nPST), ≥ 1.5 mm
contact gap
No. of poles
2 = 2 pole, 12 A
4 = 4 pole, 12 A
Coil version
8 = AC (50/60 Hz)
9 = DC
Coil voltage
See coil specifications
Selecting features and options: only combinations in the same row are possible.
Preferred selections for best availability are shown in bold.
Type
B
C
D
56.32 AC
Coil version A
0-2-4
0
0-2-3-4-5
0
AC
0-2-4
0
54
AC
0-2-4
3
0-3-5
0
DC
0-2-4
0
0-2-4-6-7-8-9
0
DC
0-2-4
0
74 - 94
56.34 AC
0-2-4
0
0-2-3-4-5
0-6-8
AC
0-2-4
0
54
/
AC
0-2-4
0-3
0-3-5
0
DC
0-2-4
0
0-2-4-6-7
0-6-8
/
/
DC
0-2-4
0
74
/
56.42 DC
0-2-4
0
0
0-1
AC
0-2-4
0-3
0
0-1
0-2-4
0
0
0-1
0-2-4
0-3
0
0-1
56.44 AC-DC
AC
D: Special versions
0 = Standard
1 = Wash tight (RT III) for 56.42 and
56.44 only
6 = Rear flange mount (4 pole only)
8 = Rear 35 mm rail mount (4 pole only)
For other mounting options see page 6
C: Options
0 = None
2 = Mechanical indicator
3* = LED (AC)
4 = Lockable test button+mechanical indicator
5* = Lockable test button + LED (AC)
54* = Lockable test button + LED (AC) +
mechanical indicator
6* = Double LED (DC non-polarized)
7* = Lockable test button + double LED
(DC non-polarized)
74* = Lockable test button + double LED
(DC non-polarized) + mechanical indicator
8* = LED + diode (DC, polarity positive
to pin 7) for 56.32 only
9* = Lockable test button + LED + diode
(DC, polarity positive to pin 7) for
56.32 only
94* = Lockable test button + LED + diode
(DC, polarity positive to pin 7) +
mechanical indicator for 56.32 only
* Options not available for 220 V DC and
400 V AC versions.
Special versions for Rail Applications on request
C: Option 6, 7, 74
Double LED
(DC non-polarized)
O
P A
PEAN
N
T E
PEAN
3
VIII-2013, www.findernet.com
1
T
EUR
C: Option 8, 9, 94
LED + diode (DC, polarity
positive to pin 7) (56.32 only)
O
C: Option 3, 5, 54
LED (AC)
EUR
Descriptions: options and special versions
Lockable test button and mechanical flag indicator (0040, 0050, 0054, 0070, 0074, 0090, 0094)
The dual-purpose Finder test button can be used in two ways:
Case 1) The plastic pip (located directly above the test button) remains intact. In this case, when the
test button is pushed, the contacts operate. When the test button is released the contacts return to their
former state.
Case 2) The plastic pip is broken-off (using an appropriate cutting tool). In this case, (in addition to
the above function), when the test button is pushed and rotated, the contacts are latched in the
operating state, and remain so until the test button is rotated back to its former position.
2
In both cases ensure that the test button actuation is swift and decisive.
3
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
56
SERIES
56 Series - Miniature power relays 12 A
Technical data
*Only in applications where over voltage category II is permitted. In applications of over voltage category III: Micro-disconnection.
Insulation according to EN 61810-1
Nominal voltage of supply system
V AC
Rated insulation voltage
V AC
Pollution degree
Insulation between coil and contact set
Type of insulation
Overvoltage category
Rated impulse voltage
kV (1.2/50 µs)
Dielectric strength
V AC
Insulation between adjacent contacts
Type of insulation
Overvoltage category
Rated impulse voltage
kV (1.2/50 µs)
Dielectric strength
V AC
Insulation between open contacts
Type of disconnection
Overvoltage category
Rated impulse voltage
kV (1.2/50 µs)
Dielectric strength
V AC/(1.2/50 µs)
Conducted disturbance immunity
Burst (5...50) ns, 5 kHz, on A1 - A2
Surge (1.2/50 µs) on A1 - A2 (differential mode)
Other data
Bounce time: NO/NC
ms
Vibration resistance (10…150 Hz ): NO/NC
g
Shock resistance NO/NC
g
Power lost to the environment
without contact current
W
with rated current
W
Recommended distance between relays mounted on PCB
mm
2 CO - 4 CO
230/400
250
3
400
2
2 NO - 4 NO
230/400
250
3
400
2
Basic
III
4
2,500
Basic
III
4
2,500
Basic
III
4
2,500
Basic
III
4
2,500
Micro-disconnection
—
—
1,000/1.5
Full-disconnection*
II
2.5
2,000/3
EN 61000-4-4
EN 61000-4-5
level 4 (4 kV)
level 4 (4 kV)
1/4 (changeover)
17/14
20/14
1 (56.32, 56.42)
3.8 (56.32, 56.42)
≥ 5
3/— (normally open)
1.3 (56.34, 56.44)
6.9 (56.34, 56.44)
Contact specification
Resistive load - cosϕ = 1
Inductive load - cosϕ = 0.4
contacts in series
DC voltage (V)
H 56 - Maximum DC1 breaking capacity
Normally open version
contacts in series
DC voltage (V)
• When switching a resistive load (DC1) having voltage and current values under the curve, an electrical life of ≥ 100·103 can be expected.
• In the case of DC13 loads, the connection of a diode in parallel with the load will permit a similar electrical life as for a DC1 load.
Note: the release time of the load will be increased.
VIII-2013, www.findernet.com
DC breaking current (A)
H 56 - Maximum DC1 breaking capacity
Changeover version
DC breajking current (A)
Cycles
F 56 - Electrical life (AC) v contact current
2 - 4 pole relays
4
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
56
SERIES
56 Series - Miniature power relays 12 A
Coil specifications
DC coil data, 2 pole relay
Nominal
Coil
voltage
code
AC coil data, 2 pole relay
Operating range
Resistance Rated coil
Nominal
Coil
consumption
voltage
code
Operating range
Resistance
UN
Umin
Umax
R
I at UN
UN
Umin*
Umax
R
V
V
V
Ω
mA
V
V
V
Ω
4.8
6.6
40
150
6
8.006
6
9.006
12
9.012
9.6
13.2
140
86
12
24
9.024
19.2
26.4
600
40
24
48
9.048
38.4
52.8
2,400
20
60
9.060
48
66
4,000
15
110
9.110
88
121
12,500
125
9.125
100
138
220
9.220
176
242
Rated coil
consumption
4.8
6.6
8.012
9.6
8.024
19.2
48
8.048
60
8.8
17,300
54,000
I at UN (50Hz)
mA
12
200
13.2
50
97
26.4
190
53
38.4
52.8
770
25
8.060
48
66
1,200
21
110
8.110
88
121
3,940
12.5
7.2
120
8.120
96
132
4,700
12
4
230
8.230
184
253
17,000
6
240
8.240
192
264
19,100
5.3
* Umin = 0.85 UN for normally open version.
DC coil data, 4 pole relay
Nominal
Coil
voltage
code
AC coil data, 4 pole relay or 4 NO
Operating range
Resistance
Rated coil
Nominal
Coil
consumption
voltage
code
Operating range
Resistance
UN
Umin
Umax
R
I at UN
UN
Umin*
Umax
R
V
V
V
Ω
mA
V
V
V
Ω
6
9.006
5.1
6.6
12
9.012
10.2
13.2
24
9.024
20.4
26.4
48
9.048
40.8
60
9.060
51
110
9.110
93.5
125
9.125
220
9.220
185
6
8.006
123
97
12
490
49
24
52.8
1,800
27
66
3,000
20
121
10,400
107
138
187
242
32.5
Rated coil
consumption
I at UN (50Hz)
mA
4.8
6.6
5.7
300
8.012
9.6
13.2
22
150
8.024
19.2
26.4
81
90
48
8.048
38.4
52.8
380
37
60
8.060
48
66
600
30
10.5
110
8.110
88
121
1,900
16.5
14,200
8.8
120
8.120
96
132
2,560
13.4
44,000
5
230
8.230
184
253
7,700
9
240
8.240
192
264
10,000
7.5
400
8.400
320
440
26,000
4.9
* Umin = 0.85 UN for normally open version.
R 56 - DC coil operating range v ambient temperature
2 pole relay
R 56 - AC coil operating range v ambient temperature
2 pole relay
normally open version
changeover version
R 56 - DC coil operating range v ambient temperature
4 pole relay
R 56 - AC coil operating range v ambient temperature
4 pole relay or 4 NO
VIII-2013, www.findernet.com
normally open version
changeover version
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
5
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
56
SERIES
56 Series - Miniature power relays 12 A
Accessories
Top flange mount adaptor for 56.32
056.25 with relay
056.25 with relay
056.25
056.27
Rear flange mount
adaptor for 56.32
056.26
056.27 with 056.26
relay
056.26 with relay
056.26
056.26 with relay
Top 35 mm rail (EN 60715) adaptor for 56.32
056.27
056.27 with relay
056.27
Top flange mount adaptor for 56.34
056.45
056.45
056.45 with relay
Top 35 mm rail (EN 60715) adaptor for 56.34
056.47
056.47
056.47 with relay
056.47 with relay
Sheet of marker tags for relay type 56.34, plastic, 72 tags, 6x12 mm
060.72
056.27 with relay
056.45 with relay
056.45
056.47
056.27
060.72
VIII-2013, www.findernet.com
056.25
056.25
6
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
56
SERIES
96 Series - Sockets and accessories for 56 series relays
Screw terminal (Box clamp) socket panel or 35 mm
(EN 60715) rail mount
For relay type
Accessories
Metal retaining clip (supplied with socket - packaging code SMA)
Plastic retaining and release clip
(supplied with socket - packaging code SPA)
6-way jumper link
Identification tag
Modules (see table below)
Timer modules (see table below)
Sheet of marker tags for retaining and release clip 094.91.3
plastic, 72 tags, 6x12 mm
Technical data
Rated values
Dielectric strength
Protection category
Ambient temperature
°C
Screw torque
Nm
Wire strip length
mm
Max. wire size for 94.02/04 sockets
mm2
AWG
96.02
Approvals
(according to type):
96.04
Approvals
(according to type):
96.02
Blue
56.32
094.71
094.91.3
094.06
095.00.4
96.02.0
Black
96.04
Blue
56.34
094.91.30
094.06.0
86.30
060.72
96.04.0
Black
096.71
—
—
—
—
090.00.2
99.02
86.00, 86.30
—
12 A - 250 V
2 kV AC
IP 20
–40…+70 (see diagram L96)
0.8
8
solid wire
stranded wire
1x6 / 2x2.5
1x4 / 2x2.5
1x10 / 2x14
1x12 / 2x14
094.91.3
Rated current (A)
L 96 - Rated current vs ambient temperature
N
T E
O
P A
96.02
96.04
96.04
PEAN
T
EUR
EUR
96.02
O
6-way jumper link for 96.02 socket
094.06 (blue)
Rated values
10 A - 250 V
86 series timer modules
Multi-voltage: (12…240)V AC/DC;
Multi-functions: AI, DI, SW, BE, CE, DE, EE, FE; (0.05 s…100 h)
(12…24)V AC/DC; Bi-function: AI, DI; (0.05 s…100 h)
(110...125)V AC; Bi-function: AI, DI; (0.05s…100h)
86.00.0.240.0000
86.30.0.024.0000
86.30.8.120.0000
(230...240)V AC; Bi-function: AI, DI; (0.05 s…100 h)
86.30.8.240.0000
094.06.0 (black)
PEAN
094.06
86.00
Approvals (according to type):
VIII-2013, www.findernet.com
86.30
99.02
Approvals
(according to type):
DC Modules with
non-standard polarity
(+A2) on request.
99.02 coil indication and EMC suppression modules for 96.02 and 96.04
Diode (+A1, standard polarity)
(6...220)V DC
LED
(6...24)V DC/AC
LED
(28...60)V DC/AC
LED
(110...240)V DC/AC
LED + Diode (+A1, standard polarity)
(6...24)V DC
LED + Diode (+A1, standard polarity)
(28...60)V DC
LED + Diode (+A1, standard polarity)
(110...220)V DC
LED + Varistor
(6...24)V DC/AC
LED + Varistor
(28...60)V DC/AC
LED + Varistor
(110...240)V DC/AC
RC circuit
(6...24)V DC/AC
RC circuit
(28...60)V DC/AC
RC circuit
(110...240)V DC/AC
Residual current by-pass
(110...240)V AC
sockets
99.02.3.000.00
99.02.0.024.59
99.02.0.060.59
99.02.0.230.59
99.02.9.024.99
99.02.9.060.99
99.02.9.220.99
99.02.0.024.98
99.02.0.060.98
99.02.0.230.98
99.02.0.024.09
99.02.0.060.09
99.02.0.230.09
99.02.8.230.07
7
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
56
SERIES
96 Series - Sockets and accessories for 56 series relays
Screw terminal (Plate clamp) socket
panel or 35 mm rail (EN 60715) mount
For relay type
96.72
Approvals
(according to type):
96.72
Blue
56.32
96.72.0
Black
Accessories
Metal retaining clip (supplied with socket - packaging code SMA) 094.71
Modules (see table below)
Technical data
Rated values
Dielectric strength
Protection category
Ambient temperature
Screw torque
Wire strip length
Max. wire size for 96.72 and 96.74 sockets
96.74
Blue
56.34
96.74.0
Black
096.71
99.01
12 A - 250 V
2 kV AC
IP 20
°C –40…+70
Nm 0.8
mm 10
solid wire
mm2 1x4 / 2x4
AWG 1x12 / 2x12
stranded wire
1x4 / 2x2.5
1x12 / 2x14
96.74
Approvals
(according to type):
96.72
96.74
99.01 coil indication and EMC suppression modules for types 96.72 and 96.74 sockets
Blue*
Diode (+A1, standard polarity)
Diode (+A2, non-standard polarity)
(6...220)V DC
99.01.3.000.00
(6...220)V DC
99.01.2.000.00
99.01
LED
(6...24)V DC/AC
99.01.0.024.59
Approvals
(according to type):
LED
(28...60)V DC/AC
99.01.0.060.59
LED
(110...240)V DC/AC
99.01.0.230.59
LED + Diode (+A1, standard polarity)
(6...24)V DC
99.01.9.024.99
LED + Diode (+A1, standard polarity)
(28...60)V DC
99.01.9.060.99
LED + Diode (+A1, standard polarity)
(110...220)V DC
99.01.9.220.99
LED + Diode (+A2, non-standard polarity)
(6...24)V DC
99.01.9.024.79
LED + Diode (+A2, non-standard polarity)
(28...60)V DC
99.01.9.060.79
LED + Diode (+A2, non-standard polarity)
(110...220)V DC
99.01.9.220.79
LED + Varistor
(6...24)V DC/AC
99.01.0.024.98
99.01.0.060.98
* Modules in Black
housing are
available on request.
LED + Varistor
(28...60)V DC/AC
LED + Varistor
(110...240)V DC/AC
99.01.0.230.98
RC circuit
(6...24)V DC/AC
99.01.0.024.09
Green LED is standard.
Red LED available on
request.
RC circuit
(28...60)V DC/AC
99.01.0.060.09
RC circuit
(110...240)V DC/AC
99.01.0.230.09
(110...240)V AC
99.01.8.230.07
VIII-2013, www.findernet.com
Residual current by-pass
8
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
56
SERIES
96 Series - Sockets and accessories for 56 series relays
96.12
Approvals
(according to type):
PCB socket
For relay type
Accessories
96.12 (blue)
56.32
Metal retaining clip (supplied with socket - packaging code SMA)
Technical data
Rated values
15 A - 250 V
Dielectric strength
Protection category
Ambient temperature
96.12.0 (black) 96.14 (blue)
56.34
96.14.0 (black)
094.51
2 kV AC
IP 20
°C –40…+70
Copper side view
96.12
Copper side view
96.14
Packaging code
How to code and identify retaining clip and packaging options for sockets.
Example:
9 6 . 7
4
S M
A
VIII-2013, www.findernet.com
A
Standard packaging
SM Metal retaining clip
SP Plastic retaining clip
9 6 . 7
4
Without retaining clip
9
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
60
SERIES
60 Series - General purpose relays 6 - 10 A
Features
60.12
60.13
2 & 3 pole changeover contacts
Cadmium Free contacts (preferred version)
• AC coils & DC coils
• UL Listing (certain relay/socket combinations)
• Contact material options
• Lockable test button with mechanical flag
indicator (preferred version)
• 90 series sockets
• Coil EMC suppression
• Timer accessories 86 series
• European Patent
Plug-in / PCB Relays
Plug-in mount
10 A General purpose relay
•
•
•
•
2 pole, 10 A power contacts
8 pin plug-in
•
•
3 pole, 10 A power contacts
11 pin plug-in
FOR UL RATINGS SEE:
“General technical information” page V
Contact specification
2 CO (DPDT)
Contact configuration
Rated current/Maximum peak current
A
Rated voltage/Maximum switching voltage V AC
3 CO (3PDT)
10/20
10/20
250/400
250/400
Rated load AC1
VA
2,500
2,500
Rated load AC15 (230 V AC)
VA
500
500
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
Standard contact material
0.37
0.37
10/0.4/0.15
10/0.4/0.15
500 (10/5)
500 (10/5)
AgNi
AgNi
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400
V DC
Rated power AC/DC
Operating range
VA (50 Hz)/W
AC
6 - 12 - 24 - 48 - 60 - 110 -125 - 220
2.2/1.3
2.2/1.3
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
Holding voltage
AC/DC
0.8 UN/0.5 UN
0.8 UN/0.5 UN
Must drop-out voltage
AC/DC
0.2 UN/0.1 UN
0.2 UN/0.1 UN
20 · 106/50 · 106
20 · 106/50 · 106
DC
Technical data
Mechanical life AC/DC
Electrical life at rated load AC1
X-2013, www.findernet.com
Operate/release time
cycles
cycles
ms
Insulation between coil and contacts (1.2/50 µs) kV
Dielectric strength between open contacts V AC
Ambient temperature range
Environmental protection
°C
3
200 · 10
200 · 103
11/4
11/4
4
3.6
1,000
1,000
–40…+70
–40…+70
RT I
RT I
Approvals (according to type)
1
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
60
SERIES
60 Series - General purpose relays 6 - 10 A
Plug-in / PCB Relays
Features
60.12 - 5200
60.13 - 5200
Plug-in mount - 6 A
Bifurcated contacts for low level switching
2 & 3 pole changeover contacts
Cadmium Free contacts
(Gold plated Silver Nickel)
• AC coils & DC coils
• Lockable test button with mechanical flag
indicator (preferred version)
• 90 series sockets
• Coil EMC suppression
• Timer accessories 86 series
• European Patent
•
•
•
•
2 pole, 6 A bifurcated contacts
8 pin plug-in
•
•
3 pole, 6 A bifurcated contacts
11 pin plug-in
FOR UL RATINGS SEE:
“General technical information” page V
Contact specification
2 CO (DPDT)
Contact configuration
Rated current/Maximum peak current
A
Rated voltage/Maximum switching voltage V AC
3 CO (3PDT)
6/10
6/10
250/400
250/400
Rated load AC1
VA
1,500
1,500
Rated load AC15 (230 V AC)
VA
250
250
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
Standard contact material
0.185
0.185
6/0.3/0.12
6/0.3/0.12
50 (5/5)
50 (5/5)
AgNi + Au bifurcated contacts
AgNi + Au bifurcated contacts
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400
V DC
Rated power AC/DC
VA (50 Hz)/W
Operating range
AC
6 - 12 - 24 - 48 - 60 - 110 -125 - 220
2.2/1.3
2.2/1.3
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
Holding voltage
AC/DC
0.8 UN/0.5 UN
0.8 UN/0.5 UN
Must drop-out voltage
AC/DC
0.2 UN/0.1 UN
0.2 UN/0.1 UN
DC
Mechanical life AC/DC
cycles
20 · 106/50 · 106
20 · 106/50 · 106
Electrical life at rated load AC1
cycles
250 · 103
250 · 103
11/4
11/4
4
3.6
Operate/release time
ms
Insulation between coil and contacts (1.2/50 µs) kV
Dielectric strength between open contacts
Ambient temperature range
Environmental protection
Approvals (according to type)
V AC
°C
1,000
1,000
–40…+70
–40…+70
RT I
RT I
X-2013, www.findernet.com
Technical data
2
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
60
SERIES
60 Series - General purpose relays 6 - 10 A
Features
60.62
60.63
Plug-in / PCB Relays
Flange mount - General purpose relay 10 A
Faston 187, 4.8x0.8 mm
2 & 3 pole changeover contacts
• AC coils & DC coils
• Cadmium Free contacts (preferred version)
• Contacts material options
•
•
•
•
2 pole, 10 A power contacts
Flange mount/Faston 187
•
•
3 pole, 10 A power contacts
Flange mount/Faston 187
FOR UL RATINGS SEE:
“General technical information” page V
Contact specification
2 CO (DPDT)
Contact configuration
Rated current/Maximum peak current
A
Rated voltage/Maximum switching voltage V AC
3 CO (3PDT)
10/20
10/20
250/400
250/400
Rated load AC1
VA
2,500
2,500
Rated load AC15 (230 V AC)
VA
500
500
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
Standard contact material
0.37
0.37
10/0.4/0.15
10/0.4/0.15
500 (10/5)
500 (10/5)
AgNi
AgNi
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400
V DC
Rated power AC/DC
VA (50 Hz)/W
Operating range
AC
6 - 12 - 24 - 48 - 60 - 110 -125 - 220
2.2/1.3
2.2/1.3
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
Holding voltage
AC/DC
0.8 UN/0.5 UN
0.8 UN/0.5 UN
Must drop-out voltage
AC/DC
0.2 UN/0.1 UN
0.2 UN/0.1 UN
20 · 106/50 · 106
20 · 106/50 · 106
DC
Technical data
Mechanical life AC/DC
Electrical life at rated load AC1
X-2013, www.findernet.com
Operate/release time
cycles
cycles
ms
Insulation between coil and contacts (1.2/50 µs) kV
Dielectric strength between open contacts
Ambient temperature range
Environmental protection
V AC
°C
3
200 · 10
200 · 103
11/4
11/4
4
3.6
1,000
1,000
–40…+70
–40…+70
RT I
RT I
Approvals (according to type)
3
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
60
SERIES
60 Series - General purpose relays 6 - 10 A
Ordering information
Plug-in / PCB Relays
Example: 60 series plug-in relay, 3 CO (3PDT), 12 V DC coil, test button and mechanical indicator.
6 0 . 1
A
B
C
D
3 . 9 . 0 1 2 . 0
0
4
0
A: Contact material
0 = Standard
2 = AgCdO
5 = AgNi + Au
Series
Type
1 = 8/11 pin plug-in
6 = Faston 187 (4.8x0.8 mm)
with flange mount
B: Contact circuit
0 = CO (nPDT)
2 = Bifurcated contacts
60.12/13 - 6 A only
No. of poles
2 = 2 pole
3 = 3 pole
Coil version
4 = Current sensing (60.12/13 only)
8 = AC (50/60 Hz)
9 = DC
Coil voltage
See coil specifications
Selecting features and options: only combinations in the same row are possible.
Preferred selections for best availability are shown in bold.
Type
Coil version
60.12/13 AC
AC
AC
AC
DC
DC
DC
DC
current sensing
60.62/63 AC-DC
A
0-2
0-2
5
5
0-2
0-2
5
5
0
0-2-5
B
0
0
000
0
000
0
2
2
2
2
C
0-2-3-4-5
54
0-2-3-4-5
54
0-2-4-6-7
74
0-2-4-6-7
74
4
0
D: Special versions
0 = Standard
C: Options
0 = None
2 = Mechanical indicator
3 = LED (AC)
4 = Lockable test button +
mechanical indicator
5* = Lockable test button + LED (AC)
54* = Lockable test button + LED (AC) +
mechanical indicator
6* = LED + diode (DC, polarity positive
to pin 2)
7* = Lockable test button + LED + diode
(DC, polarity positive to pin 2)
74* = Lockable test button + LED + diode
(DC, polarity positive to pin 2) +
mechanical indicator
* Options not available for 220 V DC and
400 V AC versions.
D
0
/
0
/
0
/
0
/
0
0
Descriptions: Options and Special versions
2
N
T E
T
The dual-purpose Finder test button can be used in two ways:
Case 1) The plastic pip (located directly above the test button) remains intact. In this case, when the
test button is pushed, the contacts operate. When the test button is released the contacts return to their
former state.
Case 2) The plastic pip is broken-off (using an appropriate cutting tool). In this case, (in addition to
the above function), when the test button is pushed and rotated, the contacts are latched in the
operating state, and remain so until the test button is rotated back to its former position.
In both cases ensure that the test button actuation is swift and decisive.
X-2013, www.findernet.com
3
P A
PEAN
PEAN
Lockable test button and mechanical flag indicator (0040, 0050, 0054, 0070, 0074)
1
O
EUR
EUR
C: Option 6, 7, 74
LED + diode (DC, polarity
positive to pin 2)
O
C: Option 3, 5, 54
LED (AC)
4
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
60
SERIES
60 Series - General purpose relays 6 - 10 A
Technical data
2 pole
Rated insulation voltage
Pollution degree
Insulation between coil and contact set
Type of insulation
Overvoltage category
Rated impulse voltage
V AC
230/400
V AC
250
3
250
3
400
2
Basic
III
3.6
V AC
2,000
2,000
Basic
Basic
kV (1.2/50 µs)
V AC
III
4
2,000
III
3.6
2,000
Micro-disconnection
1,000/1.5
Micro-disconnection
1,000/1.5
EN 61000-4-4
EN 61000-4-5
level 4 (4 kV)
level 4 (4 kV)
1/4
22/22
20
1.3
2.7 (60.12, 60.62)
1.3
3.4 (60.13, 60.63)
kV (1.2/50 µs)
Insulation between open contacts
Type of disconnection
Dielectric strength
400
2
Basic
III
4
Dielectric strength
Insulation between adjacent contacts
Type of insulation
Overvoltage category
Rated impulse voltage
Dielectric strength
3 pole
230/400
V AC/kV (1.2/50 µs)
Conducted disturbance immunity
Burst (5...50)ns, 5 kHz, on A1 - A2
Surge (1.2/50 µs) on A1 - A2 (differential mode)
Other data
Bounce time: NO/NC
Vibration resistance (5…55)Hz: NO/NC
Shock resistance
Power lost to the environment
without contact current
with rated current
ms
g
g
W
W
Plug-in / PCB Relays
Insulation according to EN 61810-1
Nominal voltage of supply system
Contact specification
H 60 - Maximum DC1 breaking capacity
Resistive load - cosϕ = 1
Inductive load - cosϕ = 0.4
contacts in series
DC breaking current (A)
Cycles
F 60 - Electrical life (AC) v contact current
DC voltage (V)
• When switching a resistive load (DC1) having voltage and current
values under the curve, an electrical life of ≥ 100·103 can be expected.
• In the case of DC13 loads, the connection of a diode in parallel with
the load will permit a similar electrical life as for a DC1 load.
Note: the release time for the load will be increased.
AC coil data
Coil specifications
X-2013, www.findernet.com
DC coil data
Nominal
voltage
UN
V
6
12
24
48
60
110
125
220
Coil
code
9.006
9.012
9.024
9.048
9.060
9.110
9.125
9.220
Operating range
Umin
V
4.8
9.6
19.2
38.4
48
88
100
176
Umax
V
6.6
13.2
26.4
52.8
66
121
138
242
Resistance Rated coil
consumption
R
I at UN
Ω
mA
28
214
110
109
445
53.9
1,770
27.1
2,760
21.7
9,420
11.7
12,000
10.4
37,300
5.8
Nominal
voltage
UN
V
6
12
24
48
60
110
120
230
240
400
Coil
code
8.006
8.012
8.024
8.048
8.060
8.110
8.120
8.230
8.240
8.400
Operating range
Umin
V
4.8
9.6
19.2
38.4
48
88
96
184
192
320
Umax
V
6.6
13.2
26.4
52.8
66
121
132
253
264
440
Resistance Rated coil
consumption
R
I at UN (50Hz)
Ω
mA
4.6
367
19
183
74
90
290
47
450
37
1,600
20
1,940
18.6
7,250
10.5
8,500
9.2
19,800
6
5
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
60
SERIES
60 Series - General purpose relays 6 - 10 A
Coil specifications
R 60 - AC coil operating range v ambient temperature
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
Plug-in / PCB Relays
R 60 - DC coil operating range v ambient temperature
Current sensing version
Current sensing DC coil data
Coil code
4202
4182
4162
4142
4122
4102
4092
4062
4032
4012
L
N
Typical application with current sensing relays.
An open circuit filiment of lamp L1 is detected by the current sensing
relay coil (K1) which causes the back-up safety lamp L2 to be energised,
and indication of failure at the control panel via lamp S1.
Example: navigation light.
L1 = Light
L2 = Safety light
S1 = Control light
K1 = Relay
Imin (A)
1.7
1.5
1.4
1.2
1.0
0.85
0.8
0.5
0.25
0.085
IN (A)
2.0
1.8
1.6
1.4
1.2
1.0
0.9
0.6
0.3
0.1
Imax (A)
2.4
2.2
1.9
1.7
1.4
1.2
1.1
0.7
0.4
0.15
R (Ω)
0.15
0.19
0.24
0.31
0.42
0.61
0.75
1.70
6.70
61
IN (A)
2.5
1.8
1.6
1.2
1.0
0.5
0.4
0.3
0.2
0.1
Imax (A)
3.0
2.2
1.9
1.4
1.2
0.6
0.5
0.4
0.25
0.15
R (Ω)
0.05
0.10
0.12
0.22
0.32
1.28
2.00
3.57
8.0
32.1
Current sensing AC coil data
Coil code
4251
4181
4161
4121
4101
4051
4041
4031
4021
4011
Imin (A)
2.1
1.5
1.4
1.0
0.85
0.42
0.34
0.25
0.17
0.085
Other types of current sensing relays are available on request.
Sheet of marker tags for relay types 60.12 and 60.13, plastic, 72 tags, 6x12 mm
060.72
060.72
X-2013, www.findernet.com
Accessories
6
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
60
SERIES
Module Socket
99.02 90.02
90.03
Relay Description
60.12 Screw terminal (Box clamp) socket
60.13 Double A1 terminal
Mounting
Panel or 35 mm rail
(EN 60715) mount
Accessories
- Coil indication and EMC
suppression modules
- Jumper link
- Timer modules
- Metal retaining clip
Module Socket
99.01 90.20
90.21
Relay Description
60.12 Screw terminal (Box clamp) socket
60.13
Mounting
Panel or 35 mm rail
(EN 60715) mount
Accessories
- Coil indication and EMC
suppression modules
- Metal retaining clip
Module Socket Relay Description
— 90.82.3 60.12 Screw terminal (Box clamp) socket
— 90.83.3 60.13
Mounting
Panel or 35 mm rail
(EN 60715) mount
Accessories
- Metal retaining clip
Module Socket
—
90.22
—
90.23
Relay Description
60.12 Screw terminal (Box clamp) socket
60.13
Mounting
Panel or 35 mm rail
(EN 60715) mount
Accessories
- Metal retaining clip
Module Socket
—
90.26
—
90.27
Relay Description
60.12 Screw terminal (Plate clamp) socket
60.13
Mounting
Panel or 35 mm rail
(EN 60715) mount
Accessories
- Metal retaining clip
Module Socket
—
90.12
—
90.13
Relay Description
60.12 Flange mount solder socket
60.13
Mounting
M3 screw fixing
Accessories
—
Module
—
—
—
—
Relay Description
60.12 PCB socket
60.12
60.13
60.13
Mounting
PCB
Accessories
—
90.03
See page 8
Plug-in / PCB Relays
90 Series - Socket overview for 60 series relays
90.21
See page 9
90.83.3
See page 10
90.23
See page 10
90.26
See page 11
90.12
See page 1
90.15
X-2013, www.findernet.com
See page 12
Socket
90.14
90.14.1
90.15
90.15.1
7
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
60
SERIES
Screw terminal (Box clamp) socket
panel or 35 mm rail (EN 60715) mount
For relay type
Accessories
Metal retaining clip
90.03
6-way jumper link
Identification tag
Approvals
(according to type):
Modules (see table below)
Timer modules (see table below)
Technical data
Rated values
Dielectric strength
Protection category
Certain relay/socket
Ambient temperature
combinations
Screw torque
Wire strip length
Max. wire size for 90.02 and 90.03 sockets
90.02
Blue
60.12
N
T E
O
EUR
90.03.0
Black
°C
Nm
mm
10 A - 250 V
2 kV AC
IP 20
–40...+70
0.6
10
solid wire
1x6 / 2x2.5
1x10 / 2x14
stranded wire
1x4 / 2x2.5
1x12 / 2x14
PEAN
T
EUR
P A
90.03
Blue
60.13
090.33
090.06
090.00.2
99.02
86.00, 86.30
mm2
AWG
O
90.02.0
Black
PEAN
090.06
86.00
86.30
99.02
Approvals
(according to type):
DC Modules with
non-standard polarity
(+A2) on request.
6-way jumper link for 90.02 and 90.03 sockets
Rated values
090.06 (blue)
10 A - 250 V
090.06.0 (black)
Approvals
(according to type):
86 series timer modules
Multi-voltage: (12…240)V AC/DC;
Multi-functions: AI, DI, SW, BE, CE, DE, EE, FE; (0.05 s…100 h)
(12…24)V AC/DC; Bi-function: AI, DI; (0.05 s…100 h)
(110...125)V AC; Bi-function: AI, DI; (0.05s…100h)
86.00.0.240.0000
86.30.0.024.0000
86.30.8.120.0000
(230...240)V AC; Bi-function: AI, DI; (0.05 s…100 h)
86.30.8.240.0000
Approvals (according to type):
99.02 coil indication and EMC suppression modules for 90.02 and 90.03 sockets
Diode (+A1, standard polarity)
(6...220)V DC 99.02.3.000.00
LED
(6...24)V DC/AC 99.02.0.024.59
LED
(28...60)V DC/AC 99.02.0.060.59
LED
(110...240)V DC/AC 99.02.0.230.59
LED + Diode (+A1, standard polarity)
(6...24)V DC 99.02.9.024.99
LED + Diode (+A1, standard polarity)
(28...60)V DC 99.02.9.060.99
LED + Diode (+A1, standard polarity)
(110...220)V DC 99.02.9.220.99
LED + Varistor
(6...24)V DC/AC 99.02.0.024.98
LED + Varistor
(28...60)V DC/AC 99.02.0.060.98
LED + Varistor
(110...240)V DC/AC 99.02.0.230.98
RC circuit
(6...24)V DC/AC 99.02.0.024.09
RC circuit
(28...60)V DC/AC 99.02.0.060.09
RC circuit
(110...240)V DC/AC 99.02.0.230.09
Residual current by-pass
(110...240)V AC 99.02.8.230.07
X-2013, www.findernet.com
Plug-in / PCB Relays
90 Series - Sockets and accessories for 60 series relays
8
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
60
SERIES
90 Series - Sockets and accessories for 60 series relays
Approvals
(according to type):
90.20
99.01
Approvals
(according to type):
* Modules in Black
housing are
available on request.
90.20.0
Black
90.21
Blue
60.13
90.21.0
Black
090.33
99.01
10 A - 250 V
2 kV AC
IP 20
–40…+70
0.5
10
solid wire
1x6 / 2x2.5
1x10 / 2x14
stranded wire
1x6 / 2x2.5
1x10 / 2x14
90.21
99.01 coil indication and EMC suppression modules for 90.20 and 90.21 sockets
See technical data page 215/216
Diode (+A1, standard polarity)
(6...220)V DC
Diode (+A2, non-standard polarity)
(6...220)V DC
LED
(6...24)V DC/AC
LED
(28...60)V DC/AC
LED
(110...240)V DC/AC
LED + Diode (+A1, standard polarity)
(6...24)V DC
LED + Diode (+A1, standard polarity)
(28...60)V DC
LED + Diode (+A1, standard polarity)
(110...220)V DC
LED + Diode (+A2, non-standard polarity)
(6...24)V DC
LED + Diode (+A2, non-standard polarity)
(28...60)V DC
LED + Diode (+A2, non-standard polarity)
(110...220)V DC
LED + Varistor
(6...24)V DC/AC
LED + Varistor
(28...60)V DC/AC
LED + Varistor
(110...240)V DC/AC
RC circuit
(6...24)V DC/AC
RC circuit
(28...60)V DC/AC
RC circuit
(110...240)V DC/AC
Residual current by-pass
(110...240)V AC
Blue*
99.01.3.000.00
99.01.2.000.00
99.01.0.024.59
99.01.0.060.59
99.01.0.230.59
99.01.9.024.99
99.01.9.060.99
99.01.9.220.99
99.01.9.024.79
99.01.9.060.79
99.01.9.220.79
99.01.0.024.98
99.01.0.060.98
99.01.0.230.98
99.01.0.024.09
99.01.0.060.09
99.01.0.230.09
99.01.8.230.07
X-2013, www.findernet.com
Green LED is standard.
Red LED available on
request.
90.20
Blue
60.12
Plug-in / PCB Relays
90.21
Screw terminal (Box clamp) socket
panel or 35 mm rail (EN 60715) mount
For relay type
Accessories
Metal retaining clip (supplied with socket - packaging code SMA)
Modules (see table below)
Technical data
Rated values
Dielectric strength
Protection category
Ambient temperature
°C
Screw torque
Nm
Wire strip length
mm
Max. wire size for 90.20 and 90.21 sockets
mm2
AWG
9
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
60
SERIES
90.83.3
Approvals
(according to type):
Screw terminal (Box clamp) socket
panel or 35 mm rail (EN 60715) mount
For relay type
Accessories
Metal retaining clip
Technical data
Rated values
Dielectric strength
Protection category
Ambient temperature
Screw torque
Max. wire size for 90.82.3 and 90.83.3 sockets
90.82.3
Blue
60.12
90.23
10 A - 250 V
2 kV AC
IP 20
°C –40…+70
Nm 0.8
solid wire
mm2 1x6 / 2x4
AWG 1x10 / 2x14
Screw (Box clamp) terminal socket
panel or 35 mm rail (EN 60715) mount
For relay type
Accessories
Metal retaining clip (supplied with socket - packaging code SMA)
Technical data
Rated values
Dielectric strength
Protection category
Ambient temperature
°C
Screw torque
Nm
Wire strip length
mm
Max wire size for 90.22 and 90.23 sockets
mm2
AWG
90.22
90.83.3
Blue
60.13
90.83.30
Black
090.33
90.82.3
Approvals
(according to type):
90.82.30
Black
stranded wire
1x6 / 2x4
1x10 / 2x14
90.83.3
90.22
Blue
60.12
90.23
Blue
60.13
090.33
10 A - 250 V
2 kV AC
IP 20
–40…+70
0.5
7
solid wire
1x6 / 2x2.5
1x10 / 2x14
stranded wire
1x6 / 2x2.5
1x10 / 2x14
90.23
X-2013, www.findernet.com
Plug-in / PCB Relays
90 Series - Sockets and accessories for 60 series relays
10
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
60
SERIES
90 Series - Sockets and accessories for 60 series relays
Approvals
(according to type):
90.12
90.27
Blue
60.13
090.33
10 A - 250 V
2 kV AC
IP 20
–40…+70
0.8
10
solid wire
1x4 / 2x2.5
1x12 / 2x14
90.27.0
Black
stranded wire
1x4 / 2x2.5
1x12 / 2x14
90.12 (black)
60.12
°C
90.13 (black)
60.13
10 A - 250 V
2 kV AC
–40…+70
X-2013, www.findernet.com
Approvals
(according to type):
90.26.0
Black
90.27
90.26
Flange mount solder socket mount with M3 screw
For relay type
Technical data
Rated values
Dielectric strength
Ambient temperature
90.26
Blue
60.12
Plug-in / PCB Relays
90.26
Screw terminal (Plate clamp) socket
panel or 35 mm rail (EN 60715) mount
For relay type
Accessories
Metal retaining clip (supplied with socket - packaging code SMA)
Technical data
Rated values
Dielectric strength
Protection category
Ambient temperature
°C
Screw torque
Nm
Wire strip length
mm
Max. wire size for 90.26 and 90.27 sockets
mm2
AWG
11
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
60
SERIES
90 Series - Sockets and accessories for 60 series relays
Plug-in / PCB Relays
PCB socket
90.15
Approvals
(according to type):
Blue
Blue
For relay type
Technical data
Rated values
Dielectric strength
Ambient temperature
°C
90.14
90.14 (Ø 20.5 mm)
90.14.1 (Ø 17.5 mm)
60.12
90.15 (Ø 22 mm)
90.15.1 (Ø 19 mm)
60.13
10 A - 250 V
2 kV AC
–40…+70
90.15
Packaging code
How to code and identify retaining clip and packaging options for sockets.
Example:
9 0 . 2
1
S M
A
A
Standard packaging
SM Metal retaining clip
1
Without retaining clip
X-2013, www.findernet.com
9 0 . 2
12
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
62 Series - Power relays 16 A
Features
62.22 / 62.23
62.22-0300 / 62.23-0300
Printed circuit mount
16 A Power relay
2 & 3 Pole changeover contacts or NO
(≥ 3 mm contact gap)
• AC coils & DC coils
• Reinforced insulation between coil and
contacts according to EN 60335-1, with
6 mm clearance & 8 mm creepage distance
• SELV coil-contact separator option
• Cadmium Free contact material options
•
•2
& 3 pole changeover contact
mount
• PCB
62.22
62.23
62.22-0300 62.23-0300
62.2x
•2
& 3 pole normally open contact
(≥ 3 mm contact gap)
• PCB mount
62.2x-0300
* Distance between contacts ≥ 3 mm
(EN 60730-1).
** With the AgSnO2 material the maximum
peak current is 120 A - 5 ms (NO contact).
FOR UL RATINGS SEE:
“General technical information” page V
62.22
Copper side view
62.23
Copper side view
2 CO (DPDT)
3 CO (3PDT)
62.22 - 0300
Copper side view
62.23 - 0300
Copper side view
Contact specification
Contact configuration
2 NO (DPST-NO), ≥ 3 mm* 3 NO (3PST-NO), ≥ 3 mm*
A
16/30**
16/30**
Rated voltage/Maximum switching voltage V AC
250/400
250/400
Rated current/Maximum peak current
Rated load AC1
VA
4,000
4,000
Rated load AC15 (230 V AC)
VA
750
750
Motor rating (230/400 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
Standard contact material
0.8/—
0.8/1.5
0.8/—
0.8/1.5
16/0.6/0.4
16/1.1/0.7
1,000 (10/10)
1,000 (10/10)
AgCdO
AgCdO
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
Rated power AC/DC
VA (50 Hz)/W
6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400
V DC
Operating range
AC
6 - 12 - 24 - 48 - 60 - 110 - 125 - 220
2.2/1.3
3/3
(0.8…1.1)UN
(0.85…1.1)UN
(0.8…1.1)UN
(0.85…1.1)UN
Holding voltage
AC/DC
0.8 UN/0.6 UN
0.8 UN/0.6 UN
Must drop-out voltage
AC/DC
0.2 UN/0.1 UN
0.2 UN/0.1 UN
10 · 106/30 · 106
10 · 106/30 · 106
DC
Technical data
Mechanical life AC/DC
Electrical life at rated load AC1
Operate/release time
cycles
cycles
ms
Insulation between coil and contacts (1.2/50 µs) kV
Dielectric strength between open contacts
Ambient temperature range
Environmental protection
V AC
°C
3
100 · 10
100 · 103
11/4
15/3
6
6
1,500
2,500
–40…+70
–40…+50
RT I
RT I
Approvals (according to type)
1
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
62 Series - Power relays 16 A
Features
62.32 / 62.33
62.32-0300 / 62.33-0300
Plug-in mount/Faston 187
16 A Power relay
• Plug-in
(92 series sockets) or Faston 187
(4.8x0.5 mm) with optional mounting adaptors
• 2 & 3 Pole changeover contacts or NO
(≥ 3 mm contact gap)
• AC coils & DC coils
• UL Listing (certain relay/socket combinations)
• LED, mechanical indicator & test button options
• Reinforced insulation between coil and
contacts according to EN 60335-1, with
6 mm clearance & 8 mm creepage distance
• SELV coil-contact separator option
• Cadmium Free contact material options
• Sockets and accessories
• European
•2
•2
& 3 pole normally open contact
(≥ 3 mm contact gap)
• Plug-in / Faston 187
& 3 pole changeover contact
/ Faston 187
• Plug-in
Patent
62.32
62.33
62.32-0300 62.33-0300
62.3x
62.3x-0300
* Distance between contacts ≥ 3 mm (EN 60730-1).
** With the AgSnO2 material the maximum
peak current is 120 A - 5 ms (NO contact).
FOR UL RATINGS SEE:
“General technical information” page V
62.32
62.33
62.32-0300
62.33-0300
Contact specification
Contact configuration
2 CO (DPDT)
3 CO (3PDT)
2 NO (DPST-NO), ≥ 3 mm* 3 NO (3PST-NO), ≥ 3 mm*
A
16/30**
16/30**
Rated voltage/Maximum switching voltage V AC
250/400
250/400
Rated current/Maximum peak current
Rated load AC1
VA
4,000
4,000
Rated load AC15 (230 V AC)
VA
750
750
Motor rating (230/400 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
Standard contact material
0.8/—
0.8/1.5
0.8/—
0.8/1.5
16/0.6/0.4
16/1.1/0.7
1,000 (10/10)
1,000 (10/10)
AgCdO
AgCdO
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
Rated power AC/DC
VA (50 Hz)/W
6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400
V DC
Operating range
6 - 12 - 24 - 48 - 60 - 110 - 125 - 220
2.2/1.3
3/3
AC
(0.8…1.1)UN
(0.85…1.1)UN
DC
(0.8…1.1)UN
(0.85…1.1)UN
Holding voltage
AC/DC
0.8 UN/0.6 UN
0.8 UN/0.6 UN
Must drop-out voltage
AC/DC
0.2 UN/0.1 UN
0.2 UN/0.1 UN
10 · 106/30 · 106
10 · 106/30 · 106
Technical data
Mechanical life AC/DC
Electrical life at rated load AC1
Operate/release time
cycles
cycles
ms
Insulation between coil and contacts (1.2/50 µs) kV
Dielectric strength between open contacts
Ambient temperature range
Environmental protection
V AC
°C
3
100 · 10
100 · 103
11/4
15/3
6
6
1,500
2,500
–40…+70
–40…+50
RT I
RT I
Approvals (according to type)
2
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
62 Series - Power relays 16 A
Features
62.82 / 62.83
62.82-0300 / 62.83-0300
Flange mount/Faston 250
16 A Power relay
Faston 250 (6.3x0.8 mm) termination Flange
or optional mounting adaptors
• 2 & 3 Pole changeover contacts or NO
(≥ 3 mm contact gap)
• AC coils & DC coils
• LED, mechanical indicator & test button options
• Reinforced insulation between coil and
contacts according to EN 60335-1, with
6 mm clearance & 8 mm creepage distance
• SELV coil-contact separator option
• Cadmium Free contact material options
•
•
•2
•2
& 3 pole normally open contact
(≥ 3 mm contact gap)
• Flange mount / Faston 250
& 3 pole changeover contact
mount / Faston 250
• Flange
European Patent
62.82
62.82-0300
62.83
62.83-0300
62.8x
62.8x-0300
* Distance between contacts ≥ 3 mm
(EN 60730-1).
** With the AgSnO2 material the maximum
peak current is 120 A - 5 ms (NO contact).
FOR UL RATINGS SEE:
“General technical information” page V
62.82
62.83
62.82-0300
62.83-0300
Contact specification
2 CO (DPDT)
Contact configuration
3 CO (3PDT)
2 NO (DPST-NO), ≥ 3 mm* 3 NO (3PST-NO), ≥ 3 mm*
A
16/30**
16/30**
Rated voltage/Maximum switching voltage V AC
250/400
250/400
Rated current/Maximum peak current
Rated load AC1
VA
4,000
4,000
Rated load AC15 (230 V AC)
VA
750
750
Motor rating (230/400 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
Standard contact material
0.8/—
0.8/1.5
0.8/—
0.8/1.5
16/0.6/0.4
16/1.1/0.7
1,000 (10/10)
1,000 (10/10)
AgCdO
AgCdO
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
Rated power AC/DC
VA (50 Hz)/W
6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400
V DC
Operating range
6 - 12 - 24 - 48 - 60 - 110 - 125 - 220
2.2/1.3
3/3
AC
(0.8…1.1)UN
(0.85…1.1)UN
DC
(0.8…1.1)UN
(0.85…1.1)UN
Holding voltage
AC/DC
0.8 UN/0.6 UN
0.8 UN/0.6 UN
Must drop-out voltage
AC/DC
0.2 UN/0.1 UN
0.2 UN/0.1 UN
10 · 106/30 · 106
10 · 106/30 · 106
Technical data
Mechanical life AC/DC
Electrical life at rated load AC1
Operate/release time
cycles
cycles
ms
Insulation between coil and contacts (1.2/50 µs) kV
Dielectric strength between open contacts
Ambient temperature range
Environmental protection
V AC
°C
3
100 · 10
100 · 103
11/4
15/3
6
6
1,500
2,500
–40…+70
–40…+50
RT I
RT I
Approvals (according to type)
3
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
62 Series - Power relays 16 A
Ordering information
Example: 62 series power relay + Faston 250 (6.3x0.8 mm), rear flange mount, 2 NO (DPST-NO), 12 V DC coil.
6 2 . 8
A
B
C
D
2 . 9 . 0 1 2 . 0
3
0
0
A: Contact material
0 = Standard AgCdO
4 = AgSnO2
Series
Type
2 = PCB
3 = Plug-in
8 = Faston 250 (6.3x0.8 mm)
with rear flange mount
B: Contact circuit
0 = CO (nPDT)
3 = NO (nPST),
≥ 3 mm contact gap
5 = CO (nPDT) + additional
physical separator between
coil and contacts (for SELV
applications)
6 = NO (nPST), ≥ 3 mm contact
gap + additional physical
separator between coil and
contacts (for SELV
applications)
No. of poles
2 = 2 pole
3 = 3 pole
Coil version
8 = AC (50/60 Hz)
9 = DC
Coil voltage
See coil specifications
Selecting features and options: only combinations in the same row are possible.
Preferred selections for best availability are shown in bold.
Type
Coil version
62.22/23 AC-DC
62.32/33 AC-DC
AC-DC
AC
AC
AC
DC
DC
DC
62.82/83 AC-DC
AC-DC
AC
AC
DC
DC
A
0-4
0-4
0-4
0-4
0-4
0-4
0-4
0-4
0-4
0-4
0-4
0-4
0-4
0-4
0-4
B
0-3-5-6
0-3-5-6
0-5
0
0-3
0
0
0-3
0
0-3-5-6
0-5
0
0-3
0
0-3
C
0
0
2-4
2-3-4-5
3
54
4-6-7
6
74
0
2-4
2-3-4-5
3
4-6-7
6
D
0
0-6
0-6
0-6
0-6
/
0-6
0-6
/
0-9
0
0
0
0
0
D: Special versions
0 = Standard
6 = Rear flange mount
9 = Type 62.82/83 without rear flange
mount
C: Options
0 = None
2 = Mechanical indicator
3 = LED (AC)
4 = Lockable test button +
mechanical indicator
5* = Lockable test button + LED (AC)
54* = Lockable test button + LED (AC) +
mechanical indicator
6* = LED + diode
(DC, polarity positive to pin A/A1)
7* = Lockable test button + LED + diode
(DC, polarity positive to pin A/A1)
74* = Lockable test button + LED + diode
(DC, polarity positive to pin A/A1) +
mechanical indicator
* Options not available for 220 V DC and
400 V AC versions.
Descriptions: Options and Special versions
3
1
O
P A
PEAN
N
T E
T
EUR
Lockable test button and mechanical flag indicator (0040, 0050, 0054, 0070, 0074)
EUR
B: Contact circuit 5, 6
Additional physical separator
between coil and contacts (for
SELV applications)
PEAN
C: Option 6, 7, 74
LED + diode (DC, polarity
positive to pin A/A1)
O
C: Option 3, 5, 54
LED (AC)
The dual-purpose Finder test button can be used in two ways:
Case 1) The plastic pip (located directly above the test button) remains intact. In this case, when the
test button is pushed, the contacts operate. When the test button is released the contacts return to their
former state.
Case 2) The plastic pip is broken-off (using an appropriate cutting tool). In this case, (in addition to
the above function), when the test button is pushed and rotated, the contacts are latched in the
operating state, and remain so until the test button is rotated back to its former position.
In both cases ensure that the test button actuation is swift and decisive.
2
4
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
62 Series - Power relays 16 A
Technical data
Insulation according to EN 61810-1
2 CO - 3 CO
Nominal voltage of supply system
V AC
Rated insulation voltage
V AC
Pollution degree
230/400
2 NO - 3 NO
230/400
400
400
3
3
Reinforced
Reinforced
III
III
6
6
4,000
4,000
Insulation between coil and contact set
Type of insulation
Overvoltage category
Rated impulse voltage
kV (1.2/50 µs)
Dielectric strength
V AC
Insulation between adjacent contacts
Type of insulation
Basic
Basic
Overvoltage category
III
III
4
4
2,500
2,500
Rated impulse voltage
kV (1.2/50 µs)
Dielectric strength
V AC
Insulation between open contacts
Type of disconnection
Micro-disconnection
Full-disconnection
Overvoltage category
—
III
—
4
1,500/2
2,500/4
Burst (5...50)ns, 5 kHz, on A1 - A2
EN 61000-4-4
level 4 (4 kV)
Surge (1.2/50 µs) on A1 - A2 (differential mode)
EN 61000-4-5
level 4 (4 kV)
1/5 (changeover)
3/— (normally open)
Rated impulse voltage
kV (1.2/50 µs)
Dielectric strength
V AC/kV (1.2/50 µs)
Conducted disturbance immunity
Other data
Bounce time: NO/NC
ms
Vibration resistance (10…150)Hz: NO/NC
g
20/8
Shock resistance
g
15
2 pole (CO)
Power lost to the environment
3 pole (CO)
2 pole (NO)
3 pole (NO)
without contact current
W
1.3
1.3
3
3
with rated current
W
3.3
4.3
5
6
mm
≥ 5
Recommended distance between relays mounted on PCB
5
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
62 Series - Power relays 16 A
Contact specification
Resistive load - cosϕ = 1
Inductive load - cosϕ = 0.4
DC breaking current (A)
H 62 - Maximum DC1 breaking capacity
Changeover contacts
contacts in series
Voltage DC (V)
H 62 - Maximum DC1 breaking capacity
Normally open contacts
DC breeaking current (A)
Cycles
F 62 - Electrical life (AC) v contact current
contacts in series
Voltage DC (V)
• When switching a resistive load (DC1) having voltage and current values under the curve, an electrical life of ≥ 100·103 can be expected.
• In the case of DC13 loads, the connection of a diode in parallel with the load will permit a similar electrical life as for a DC1 load.
Note: the release time of the load will be increased.
6
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
62 Series - Power relays 16 A
Coil specifications
DC version data
Nominal
voltage
UN
V
6
12
24
48
60
110
125
220
Coil
code
9.006
9.012
9.024
9.048
9.060
9.110
9.125
9.220
AC version data
Operating range
Umin
V
4.8
9.6
19.2
38.4
48
88
100
176
Umax
V
6.6
13.2
26.4
52.8
66
121
138
242
Resistance Rated coil
consumption
R
I at UN
Ω
mA
28
214
110
109
445
54
1,770
27
2,760
21.7
9,420
11.7
12,000
10.4
37,300
5.8
DC (NO/nPST-NO) version data - ≥ 3 mm
Nominal
voltage
UN
V
6
12
24
48
60
110
125
220
Coil
code
9.006
9.012
9.024
9.048
9.060
9.110
9.125
9.220
Operating range
Umin
V
5.1
10.2
20.4
40.8
51
93.5
106
187
Umax
V
6.6
13.2
26.4
52.8
66
121
138
242
Nominal
voltage
UN
V
6
12
24
48
60
110
120
230
240
400
Coil
code
8.006
8.012
8.024
8.048
8.060
8.110
8.120
8.230
8.240
8.400
Operating range
Umin
V
4.8
9.6
19.2
38.4
48
88
96
184
192
320
Umax
V
6.6
13.2
26.4
52.8
66
121
132
253
264
440
Resistance Rated coil
consumption
R
I at UN (50Hz)
Ω
mA
4.6
367
19
183
74
90
290
47
450
37
1,600
20
1,940
18.6
7,250
10.5
8,500
9.2
19,800
6
AC (NO/nPST-NO) version data - ≥ 3 mm
Resistance Rated coil
consumption
R
I at UN
Ω
mA
12
500
48
250
192
125
770
63
1,200
50
4,200
26
5,200
24
17,600
12.5
Nominal
voltage
UN
V
6
12
24
48
60
110
120
230
240
400
Coil
code
8.006
8.012
8.024
8.048
8.060
8.110
8.120
8.230
8.240
8.400
Operating range
Umin
V
5.1
10.2
20.4
40.8
51
93.5
106
196
204
340
Umax
V
6.6
13.2
26.4
52.8
66
121
137
253
264
440
Resistance Rated coil
consumption
R
I at UN (50Hz)
Ω
mA
4
540
14
275
62
130
220
70
348
55
1,200
30
1,350
24
5,000
14
6,300
12.5
14,700
7.8
R 62 - DC coil operating range v ambient temperature
Changeover contacts
R 62 - AC coil operating range v ambient temperature
Changeover contacts
R 62 - DC coil operating range v ambient temperature
Normally open contacts
R 62 - AC coil operating range v ambient temperature
Normally open contacts
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
7
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
62 Series - Power relays 16 A
Accessories
Mounting adaptor for types 62.3x and 62.8x.xxxx.xxx9 (M4)
062.10
062.10
062.10 with relay
062.10 with relay
062.10
Flange mounting adaptor for types 62.3x and 62.8x.xxxx.xxx9
062.60
062.60
062.60 with relay
062.60 with relay
062.60
Top flange mount for types 62.3x and 62.8x.xxxx.xxx9
062.05
062.05
062.05 with relay
062.05
Top 35 mm rail (EN 60715) mount for types 62.3x and 62.8x.xxxx.xxx9
062.05 with relay
062.07
062.07
062.07 with relay
062.07
062.07 with relay
8
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
62 Series - Power relays 16 A
Accessories
Rear 35 mm rail (EN 60715) mount for types 62.3x and 62.8x.xxxx.xxx9
062.08
062.08
062.08 with relay
062.08
Sheet of marker tags for 62 series relays, plastic, 72 tags, 6x12 mm
062.08 with relay
060.72
060.72
9
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
92 Series - Sockets and accessories for 62 series relays
92.03
Approvals
(according to type):
Screw terminal (Box clamp) socket
panel or 35 mm rail (EN 60715) mount
For relay type
Accessories
Metal retaining clip (supplied with socket - packaging code SMA)
Identification tag
Modules (see table below)
Timer modules (see table below)
Technical data
Rated values
Dielectric strength
Protection category
Ambient temperature
°C
Screw torque
Nm
Wire strip length
mm
Max. wire size for 92.03 socket
mm2
AWG
92.03
Blue
62.32, 62.33
92.03.0
Black
092.71
092.00.2
99.02
86.00, 86.30
16 A - 250 V
6 kV (1.2/50 µs) between coil and contacts
IP 20
–40…+70 (see diagram L92)
0.8
10
solid wire
stranded wire
1x10 / 2x4
1x6 / 2x4
1x8 / 2x12
1x10 / 2x12
Rated current (A)
L 92 - Rated current vs ambient temperature
86 series timer modules
Multi-voltage: (12…240)V AC/DC;
Multi-functions: AI, DI, SW, BE, CE, DE, EE, FE; (0.05s…100h)
(12…24)V AC/DC; Bi-function: AI, DI; (0.05s…100h)
86.00
86.00.0.240.0000
86.30.0.024.0000
(110...125)V AC; Bi-function: AI, DI; (0.05s…100h)
86.30.8.120.0000
(230...240)V AC; Bi-function: AI, DI; (0.05s…100h)
86.30.8.240.0000
Approvals
(according to type):
86.30
99.02
Approvals
(according to type):
DC Modules with
non-standard polarity
(+A2) on request.
99.02 coil indication and EMC suppression modules for 92.03 socket
Diode (+A1, standard polarity)
(6...220)V DC
LED
(6...24)V DC/AC
LED
(28...60)V DC/AC
LED
(110...240)V DC/AC
LED + Diode (+A1, standard polarity)
(6...24)V DC
LED + Diode (+A1, standard polarity)
(28...60)V DC
LED + Diode (+A1, standard polarity)
(110...220)V DC
LED + Varistor
(6...24)V DC/AC
LED + Varistor
(28...60)V DC/AC
LED + Varistor
(110...240)V DC/AC
RC circuit
(6...24)V DC/AC
RC circuit
(28...60)V DC/AC
RC circuit
(110...240)V DC/AC
Residual current by-pass
(110...240)V AC
99.02.3.000.00
99.02.0.024.59
99.02.0.060.59
99.02.0.230.59
99.02.9.024.99
99.02.9.060.99
99.02.9.220.99
99.02.0.024.98
99.02.0.060.98
99.02.0.230.98
99.02.0.024.09
99.02.0.060.09
99.02.0.230.09
99.02.8.230.07
10
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
92 Series - Sockets and accessories for 62 series relays
92.13
Approvals
(according to type):
PCB socket
For relay type
Accessories
Metal retaining clip (supplied with socket - packaging code SMA)
Technical data
Rated values
Dielectric strength
Ambient temperature
°C
92.13 (blue)
62.32, 62.33
92.13.0 (black)
092.54
10 A - 250 V
2.5 kV AC
–40…+70
62.3x plug on 92.13 is 63.3 mm high
92.33
Approvals
(according to type):
Panel mount solder socket mounted with M3 screw
For relay type
Accessories
Metal retaining clip (supplied with socket - packaging code SMA)
Technical data
Rated values
Dielectric strength
Ambient temperature
°C
92.33 (blue)
62.32, 62.33
092.54
10 A - 250 V
2.5 kV AC
–40…+70
Packaging code
How to code and identify retaining clip and packaging options for sockets.
Example:
9 2 . 0
3
S M
A
A
Standard packaging
SM Metal retaining clip
9 2 . 0
3
Without retaining clip
11
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
65 Series - Power relays 20 - 30 A
Features
65.31
65.61
20 A Power relays
1 NO + 1 NC (SPST-NO + SPST-NC)
65.31 Flange mount
Faston 250 connections
65.61 PCB mount
•
•
AC coils & DC coils
Cadmium Free option available
•
•
20 A rated contacts
Flange mount/Faston 250
(6.3x0.8 mm) connection
•
•
20 A rated contacts
PCB mount bifurcated terminals
65.61
* With the AgSnO2 material the maximum
peak current is 120 A - 5 ms on NO contact.
FOR UL RATINGS SEE:
“General technical information” page V
Copper side view
Contact specification
1NO+1NC (SPST-NO+SPST-NC) 1NO+1NC (SPST-NO+SPST-NC)
Contact configuration
Rated current/Maximum peak current
A
Rated voltage/Maximum switching voltage V AC
20/40*
20/40*
250/400
250/400
Rated load AC1
VA
5,000
5,000
Rated load AC15 (230 V AC)
VA
1,000
1,000
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
Standard contact material
1.1
1.1
20/0.8/0.5
20/0.8/0.5
1,000 (10/10)
1,000 (10/10)
AgCdO
AgCdO
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
V DC
Rated power AC/DC
VA (50 Hz)/W
Operating range
AC
6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400
6 - 12 - 24 - 48 - 60 - 110 - 125 - 220
2.2/1.3
2.2/1.3
(0.8…1.1)UN
(0.8…1.1)UN
DC
(0.85…1.1)UN
(0.85…1.1)UN
Holding voltage
AC/DC
0.8 UN/0.6 UN
0.8 UN/0.6 UN
Must drop-out voltage
AC/DC
0.2 UN/0.1 UN
0.2 UN/0.1 UN
10 · 106/30 · 106
10 · 106/30 · 106
Technical data
Mechanical life AC/DC
Electrical life at rated load AC1
Operate/release time
cycles
cycles
80 · 10
80 · 103
ms
10/12
10/12
4
4
Insulation between coil and contacts (1.2/50 µs) kV
Dielectric strength between open contacts
Ambient temperature range
Environmental protection
V AC
°C
3
1,500
1,500
–40…+75
–40…+75
RT I
RT I
Approvals (according to type)
1
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
65 Series - Power relays 20 - 30 A
Features
65.31-0300
65.61-0300
30 A Power relays
1 NO (SPST-NO)
65.31-0300
65.61-0300
Flange mount
Faston 250 connections
PCB mount
≥ 3 mm contact gap
AC coils & DC coils
• Cadmium Free option available
•
•
•
•
30 A rated contacts
Flange mount/Faston 250
(6.3x0.8 mm) connection
•
•
30 A rated contacts
PCB mount bifurcated terminals
65.61-0300
*
Distance between contacts ≥ 3 mm
(EN 60335-1).
** With the AgSnO2 material the maximum
peak current is 120 A - 5 ms on NO
contact.
FOR UL RATINGS SEE:
“General technical information” page V
Copper side view
Contact specification
1 NO (SPST-NO), ≥ 3 mm*
Contact configuration
1 NO (SPST-NO), ≥ 3 mm*
A
30/50**
30/50**
Rated voltage/Maximum switching voltage V AC
250/400
250/400
Rated current/Maximum peak current
Rated load AC1
VA
7,500
7,500
Rated load AC15 (230 V AC)
VA
1,250
1,250
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
Standard contact material
1.5
1.5
30/1.1/0.7
30/1.1/0.7
1,000 (10/10)
1,000 (10/10)
AgCdO
AgCdO
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
V DC
Rated power AC/DC
VA (50 Hz)/W
Operating range
AC
6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400
6 - 12 - 24 - 48 - 60 - 110 -125 - 220
2.2/1.3
2.2/1.3
(0.8…1.1)UN
(0.8…1.1)UN
DC
(0.85…1.1)UN
(0.85…1.1)UN
Holding voltage
AC/DC
0.8 UN/0.6 UN
0.8 UN/0.6 UN
Must drop-out voltage
AC/DC
0.2 UN/0.1 UN
0.2 UN/0.1 UN
10 · 106/30 · 106
10 · 106/30 · 106
Technical data
Mechanical life AC/DC
Electrical life at rated load AC1
Operate/release time
cycles
cycles
ms
Insulation between coil and contacts (1.2/50 µs) kV
Dielectric strength between open contacts
Ambient temperature range
Environmental protection
V AC
°C
3
50 · 10
50 · 103
15/4
15/4
4
4
2,500
2,500
–40…+75
–40…+75
RT I
RT I
Approvals (according to type)
2
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
65 Series - Power relays 20 - 30 A
Ordering information
Example: 65 series power relay, PCB with bifurcated terminals, 1 NO + 1 NC (SPST-NO + SPST-NC) contact, 12 V DC coil.
6 5 . 6
A
B
C
D
1 . 9 . 0 1 2 . 0
0
0
0
A: Contact material
0 = Standard AgCdO
4 = AgSnO2
Series
Type
3 = Faston 250 (6.3x0.8 mm)
with rear flange mount
6 = PCB with bifurcated terminals
D: Special versions
0 = Standard
9 = Type 65.31 without rear flange
mount
B: Contact circuit
0 = 1 NO + 1 NC
(SPST-NO + SPST-NC)
3 = NO (≥ 3 mm contact gap)
No. of poles
1 = 1 NO + 1 NC (SPST-NO + SPST-NC)
C: Options
0 = None
Coil version
8 = AC (50/60 Hz)
9 = DC
Coil voltage
See coil specifications
Selecting features and options: only combinations in the same row are possible.
Preferred selections for best availability are shown in bold.
Type
65.31
65.61
Coil version A
AC-DC
0-4
AC-DC
0-4
B
0-3
0-3
C
0
0
D
0 -9
0
Technical data
Insulation according to EN 61810-1
1 NO + 1 NC
1 NO
Nominal voltage supply system
V AC
230/400
Rated insulation voltage
V AC
250
400
250
400
3
2
3
2
Pollution degree
230/400
Insulation between coil and contact set
Type of insulation
Overvoltage category
Rated impulse voltage
kV (1.2/50 µs)
Dielectric strength
V AC
Basic
Basic
III
III
4
4
2,500
2,500
Insulation between open contacts
Type of disconnection
Micro-disconnection
Full-disconnection
Overvoltage category
—
III
—
4
1,500/2
2,500/4
Burst (5...50)ns, 5 kHz, on A1 - A2
EN 61000-4-4
level 4 (4 kV)
Surge (1.2/50 µs) on A1 - A2 (differential mode)
EN 61000-4-5
level 4 (4 kV)
Rated impulse voltage
kV (1.2/50 µs)
Dielectric strength
V AC/kV (1.2/50 µs)
Conducted disturbance immunity
Other data
Bounce time: NO/NC
ms
Vibration resistance (10…150)Hz: NO/NC
Shock resistance
Power lost to the environment
5/6 (1 normally open + 1 normally closed) 7/— (normally open)
g
20/13
g
20
without contact current
W
1.3
with rated current
W
2.1 (65.31, 65.61)
Recommended distance between relays mounted on PCB
mm
3.1 (65.31/.61.0300)
≥5
3
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
65 Series - Power relays 20 - 30 A
Contact specification
F 65 - Electrical life (AC) v contact current
Cycles
Resistive load - cosϕ = 1
Inductive load - cosϕ = 0.4
limit for 1NO+1NC types
DC breaking current (A)
H 65 - Maximum DC1 breaking capacity
1 normally open type
1 normally open + 1 normally closed type
DC voltage (V)
• When switching a resistive load (DC1) having voltage and current
values under the curve, an electrical life of ≥ 80·103 can be expected.
• In the case of DC13 loads, the connection of a diode in parallel with
the load will permit a similar electrical life as for a DC1 load.
Note: the release time for the load will be increased.
Coil specifications
DC coil data
Nominal
voltage
UN
V
6
12
24
48
60
110
125
220
AC coil data
Coil
code
9.006
9.012
9.024
9.048
9.060
9.110
9.125
9.220
Operating range
Umin
V
5.1
10.2
20.4
40.8
51
93.5
106
187
Umax
V
6.6
13.2
26.4
52.8
66
121
138
242
Resistance Rated coil
consumption
R
I at UN
Ω
mA
28
214
110
109
445
54
1,770
27.1
2,760
21.7
9,420
11.7
12,000
10.4
37,300
5.8
Nominal
voltage
UN
V
6
12
24
48
60
110
120
230
240
400
Coil
code
8.006
8.012
8.024
8.048
8.060
8.110
8.120
8.230
8.240
8.400
Operating range
Umin
V
4.8
9.6
19.2
38.4
48
88
96
184
192
320
Umax
V
6.6
13.2
26.4
52.8
66
121
132
253
264
440
Resistance Rated coil
consumption
R
I at UN (50Hz)
Ω
mA
4.6 367
19
183
74
90
290
47
450
37
1,600
20
1,940
18.6
7,250
10.5
8,500
9.2
19,800
6
R 65 - DC coil operating range v ambient temperature
R 65 - AC coil operating range v ambient temperature
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
4
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
65 Series - Power relays 20 - 30 A
Accessories
Top flange mount for types 65.31.xxxx.xxx9
065.05
065.05
065.05 with relay
065.05
Top 35 mm rail (EN 60715) mount for types 65.31.xxxx.xxx9
065.05 with relay
065.07
065.07
065.07 with relay
065.07
Rear 35 mm rail (EN 60715) mount for types 65.31.xxxx.xxx9
065.07 with relay
065.08
065.08
065.08
065.08 with relay
065.08 with relay
5
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
66 Series - Power relays 30 A
Features
66.22
66.82
2 Pole Changeover (DPDT)
30 A Power relay
66.22
66.82
PCB connections & mount
Faston 250 connections
- Flange mount
Reinforced insulation between coil and
contacts according to EN 60335-1;
8 mm creepage and clearance distances
• AC coils & DC coils
• Cadmium Free option available
•
•
•
30 A rated contacts
PCB mount bifurcated terminals
30 A rated contacts
Flange mount
• Faston 250 connections
•
•
For outline drawing see page 6
FOR UL RATINGS SEE:
“General technical information” page V
Copper side view
Contact specification
Contact configuration
Rated current/Maximum peak current
A
Rated voltage/Maximum switching voltage V AC
2 CO (DPDT)
2 CO (DPDT)
30/50 (NO) - 10/20 (NC)
30/50 (NO) - 10/20 (NC)
250/440
250/440
Rated load AC1
VA
7,500 (NO) - 2,500 (NC)
7,500 (NO) - 2,500 (NC)
Rated load AC15 (230 V AC)
VA
1,200 (NO)
1,200 (NO)
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
Standard contact material
1.5 (NO)
1.5 (NO)
25/0.7/0.3 (NO)
25/0.7/0.3 (NO)
1,000 (10/10)
1,000 (10/10)
AgCdO
AgCdO
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
Rated power AC/DC
VA (50 Hz)/W
6 - 12 - 24 - 110/115 - 120/125 - 230 - 240
V DC
Operating range
AC
6 - 12 - 24 - 110 - 125
3.6/1.7
3.6/1.7
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
Holding voltage
AC/DC
0.8 UN/0.5 UN
0.8 UN/0.5 UN
Must drop-out voltage
AC/DC
0.2 UN/0.1 UN
0.2 UN/0.1 UN
10 · 106
10 · 106
DC
Technical data
Mechanical life AC/DC
Electrical life at rated load AC1
VII-2012, www.findernet.com
Operate/release time
cycles
cycles
ms
Insulation between coil and contacts (1.2/50 μs) kV
Dielectric strength between open contacts
Ambient temperature range
Environmental protection
V AC
°C
3
100 · 10
100 · 103
8/15
8/15
6 (8 mm)
6 (8 mm)
1,500
1,500
–40…+70
–40…+70
RT II
RT II
Approvals (according to type)
1
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
66 Series - Power relays 30 A
Features
66.22-x300
66.82-x300
2 Pole NO (DPST-NO)
30 A Power relay
66.22-x300
66.82-x300
PCB mount
Faston 250 connections
- Flange mount
Reinforced insulation between coil and
contacts according to EN 60335-1;
8 mm creepage and clearance distances
• AC coils & DC coils
• Cadmium Free option available
•
•
•
30 A rated contacts
PCB mount bifurcated terminals
30 A rated contacts
Flange mount
• Faston 250 connections
•
•
For outline drawing see page 6
FOR UL RATINGS SEE:
“General technical information” page V
Copper side view
Contact specification
2 NO (DPST-NO)
Contact configuration
Rated current/Maximum peak current
A
Rated voltage/Maximum switching voltage V AC
2 NO (DPST-NO)
30/50
30/50
250/440
250/440
Rated load AC1
VA
7,500
7,500
Rated load AC15 (230 V AC)
VA
1,200
1,200
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
Standard contact material
1.5
1.5
25/0.7/0.3
25/0.7/0.3
1,000 (10/10)
1,000 (10/10)
AgCdO
AgCdO
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
Rated power AC/DC
VA (50 Hz)/W
6 - 12 - 24 - 110/115 - 120/125 - 230 - 240
V DC
Operating range
AC
6 - 12 - 24 - 110 -125
3.6/1.7
3.6/1.7
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
(0.8…1.1)UN
Holding voltage
AC/DC
0.8 UN/0.5 UN
0.8 UN/0.5 UN
Must drop-out voltage
AC/DC
0.2 UN/0.1 UN
0.2 UN/0.1 UN
10 · 106
10 · 106
DC
Technical data
Electrical life at rated load AC1
cycles
cycles
3
100 · 10
100 · 103
Operate/release time
ms
8/10
8/10
Insulation between coil and contacts (1.2/50 μs)
kV
6 (8 mm)
6 (8 mm)
Dielectric strength between open contacts
Ambient temperature range
Environmental protection
Approvals (according to type)
V AC
°C
1,500
1,500
–40…+70
–40…+70
RT II
RT II
VII-2012, www.findernet.com
Mechanical life AC/DC
2
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
66 Series - Power relays 30 A
Features
66.22-x600
66.22-x600S
66.82-x600
2 Pole NO (DPST-NO), ≥1.5mm contact gap
30 A Power relay
66.22-x600 PCB mount
66.22-x600S PCB mount - 5 mm gap
between PCB and relay base
66.82-x600 Faston 250 connections
- Flange mount
≥1.5 mm contact gap (according to VDE 0126-1-1
for solar inverter applications)
• Reinforced insulation between coil and
contacts according to EN 60335-1;
8 mm creepage and clearance distances
• Wash tight version (RT III) available
• DC coils
• Cadmium Free option available
•
•
PCB mount bifurcated terminals
PCB mount bifurcated terminals
• 5 mm gap between PCB and
relay base
•
•
•
Flange mount
Faston 250 connections
For outline drawing see page 6
FOR UL RATINGS SEE:
“General technical information” page V
Copper side view
Copper side view
2 NO (DPST-NO)
2 NO (DPST-NO)
Contact specification
Contact configuration
Rated current/Maximum peak current
A
Rated voltage/Maximum switching voltage V AC
2 NO (DPST-NO)
30/50
30/50
30/50
250/440
250/440
250/440
Rated load AC1
VA
7,500
7,500
7,500
Rated load AC15 (230 V AC)
VA
1,200
1,200
1,200
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A
mW (V/mA)
Standard contact material
1.5
1.5
1.5
30/1.2/0.5
30/1.2/0.5
30/1.2/0.5
1,000 (10/10)
1,000 (10/10)
1,000 (10/10)
AgCdO
AgCdO
AgCdO
Coil specification
Nominal voltage (UN)
V AC (50/60 Hz)
Rated power AC/DC
VA (50 Hz)/W
—
V DC
Operating range
6 - 12 - 24 - 110 -125
—/1.7
—/1.7
—/1.7
AC
—
—
—
DC
(0.8…1.1)UN
(0.7…1.1)UN
(0.8…1.1)UN
Holding voltage
AC/DC
—/0.5 UN
—/0.5 UN
—/0.5 UN
Must drop-out voltage
AC/DC
—/0.1 UN
—/0.1 UN
—/0.1 UN
10 · 106
10 · 106
10 · 106
Technical data
Mechanical life
VII-2012, www.findernet.com
Electrical life at rated load AC1
cycles
cycles
3
100 · 10
3
100 · 10
100 · 103
Operate/release time
ms
15/4
15/4
15/4
Insulation between coil and contacts (1.2/50 μs)
kV
6 (8 mm)
6 (8 mm)
6 (8 mm)
Dielectric strength between open contacts
Ambient temperature range
Environmental protection
V AC
°C
2,500
2,500
2,500
–40…+70
–40…+70
–40…+70
RT II
RT II
RT II
Approvals (according to type)
3
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
66 Series - Power relays 30 A
Ordering information
Example: 66 series relay, Faston 250 (6.3x0.8 mm) with top flange mount, 2 CO (DPDT) 30 A contacts, 24 V DC coil.
6 6 . 8
A
B
C
D
2 . 9 . 0 2 4 . 0
0
0
0
Series
A: Contact material
0 = Standard AgCdO
1 = AgNi
Type
2 = PCB
8 = Faston 250 (6.3x0.8 mm)
with top flange mount
B: Contact circuit
0 = CO (nPDT)
3 = NO (nPST)
6 = NO (nPST), ≥1.5 mm
contact gap
No. of poles
2 = 2 pole, 30 A
Coil version
8 = AC (50/60 Hz)
9 = DC
S = PCB version with 5 mm gap
between PCB and relay base
(only 66.22)
D: Special versions
0 = Standard
1 = Wash tight (RT III)
C: Options
0 = None
Coil voltage
See coil specifications
Selecting features and options: only combinations in the same row are possible.
Preferred selections for best availability are shown in bold.
Type
66.22
Coil version
AC-DC
DC
66.22....S DC
66.82
AC-DC
DC
A
0-1
0-1
0-1
0-1
0-1
B
0-3
6
6
0-3
6
C
0
0
0
0
0
D
0-1
0-1
0-1
0-1
0-1
Technical data
Insulation according to EN 61810-1
Nominal voltage of supply system
V AC
230/400
Rated insulation voltage
V AC
400
Pollution degree
3
Insulation between coil and contact set
Type of insulation
Reinforced (8 mm)
Overvoltage category
III
Rated impulse voltage
kV (1.2/50 μs)
Dielectric strength
V AC
6
4,000
Insulation between adjacent contacts
Type of insulation
Basic
Overvoltage category
III
Rated impulse voltage
kV (1.2/50 μs)
Dielectric strength
V AC
Insulation between open contacts
4
2,500
2 CO
2 NO, ≥1.5mm (x600 version)
Type of disconnection
Micro-disconnection
Full-disconnection *
Overvoltage category
—
II
—
2.5
1,500/2
2,500/3
Burst (5...50)ns, 5 kHz, on A1 - A2
EN 61000-4-4
level 4 (4 kV)
Surge (1.2/50 μs) on A1 - A2 (differential mode)
EN 61000-4-5
level 4 (4 kV)
Rated impulse voltage
kV (1.2/50 μs)
Dielectric strength
V AC/kV (1.2/50 μs)
Conducted disturbance immunity
Other data
ms
7/10
Vibration resistance (10...150)Hz: NO/NC
g
20/19
Shock resistance
g
20
Power lost to the environment
without contact current
W
2.3
with rated current
W
5
Recommended distance between relays mounted on PCB
mm
≥ 10
* Only in applications where over voltage category II is permitted. In applications of over voltage category III: Micro-disconnection.
VII-2012, www.findernet.com
Bounce time: NO/NC
4
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
66 Series - Power relay 30 A
Contact specification
F 66 - Electrical life (AC) v contact current
440 V (normally open contact)
Cycles
Resistive load - 250 V AC cosϕ = 1
Inductive load - 250 V AC cosϕ = 0.4
H 66 - Maximum DC breaking capacity
Resistive load - 440 V AC cosϕ = 1
Inductive load - 440 V AC cosϕ = 0.4
Cycles
F 66 - Electrical life (AC) v contact current
250 V (normally open contact)
DC breaking current (A)
DC breaking current (A)
H 66 - Maximum DC breaking capacity, x600 versions
(>1.5mm contact gap)
DC voltage (V)
DC voltage (V)
• When switching a resistive load (DC1) having voltage and current values under the curve, an electrical life of ≥ 100·103 can be expected.
• In the case of DC13 loads, the connection of a diode in parallel with the load will permit a similar electrical life as for a DC1 load.
Note: the release time for the load will be increased.
Coil specifications
DC coil data
Nominal
voltage
UN
V
6
12
24
110
125
AC coil data
Coil
code
9.006
9.012
9.024
9.110
9.125
Operating range
Umin
V
4.8
9.6
19.2
88
100
Umax
V
6.6
13.2
26.4
121
138
Resistance Rated coil
consumption
R
I at UN
Ω
mA
21
283
85
141
340
70.5
7,000
15.7
9,200
13.6
VII-2012, www.findernet.com
R 66 - DC coil operating range v ambient temperature
Nominal
voltage
UN
V
6
12
24
110/115
120/125
230
240
Coil
code
8.006
8.012
8.024
8.110
8.120
8.230
8.240
Operating range
Umin
V
4.8
9.6
19.2
88
96
184
192
Umax
V
6.6
13.2
26.4
126
137
253
264
Resistance Rated coil
consumption
R
I at UN (50Hz)
Ω
mA
3
600
11
300
50
150
930
32.6
1,050
30
4,000
15.7
5,500
15
R 66 - AC coil operating range v ambient temperature
1 - Max. permitted coil voltage.
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
2 - Min. pick-up voltage with coil at ambient temperature.
3 - Min. pick-up voltage with coil at ambient temperature (66.22-x600S).
5
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
66 Series - Power relay 30 A
Outline drawings
Type 66.22
Type 66.82
Type 66.22-0300
Type 66.82-0300
Type 66.22-0600
Type 66.82-0600
Type 66.22-0600S
Accessories
Top 35 mm rail (EN 60715) mount for types 66.82.xxxx.0x00
066.07
066.07 with relay
066.07
066.07 with relay
VII-2012, www.findernet.com
066.07
6
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
67
SERIES
67 Series - Solar relay 50 A
Features
67.22-4300
67.23-4300
2 and 3 pole versions
(NO, double break contacts)
• Contact gap ≥ 3 mm (according to
VDE 0126-1-1, EN 62109-1, EN 62109-2)
• DC coils, with only 170 mW holding power
• Reinforced insulation between coil and contacts
• 1.5 mm gap between PCB and relay base
• Suitable for use at ambient temperatures up to
85 °C (with energy-saving coil energization)
or 70 °C (with standard coil energization)
Plug-in / PCB Relays
Printed circuit mount - 3 mm contact gap
50 A Power relay for photovoltaic inverters
•
For outline drawing see page 6
•2
NO
•3
• Contact
gap ≥ 3 mm
• PCB mount
NO
• Contact
• PCB
gap ≥ 3 mm
mount
Copper side view
Copper side view
2 NO (DPST-NO)
3 NO (3PST-NO)
≥3
≥3
Contact specification
Contact configuration
Contact gap
mm
Rated current/Maximum peak current (for 5 ms) A
50/150
50/150
Rated voltage/Maximum switching voltage V AC
400/690
400/690
Rated load AC1/AC7a (per pole)
VA
20,000
20,000
Rated load AC15 (per pole @ 230 V AC)
VA
2,300
2,300
Single-phase motor rating (230 V AC)
kW
2
2
Three-phase motor rating (480 V AC)
kW
—
7
50/4/1
50/4/1
1,000 (10/10)
1,000 (10/10)
AgSnO2
AgSnO2
Breaking capacity DC1: 24/110/220 V
Minimum switching load
A
mW (V/mA)
Standard contact material
Coil specification
Nominal voltage (UN)
Rated power
Operating range (–40…+70°C)
V DC
5 - 6 - 8 - 12 - 24 - 48 - 60 - 110
W
1.7
1.7
DC
(0.90 …1.1) UN
(0.90 …1.1) UN
(0.95…2.5) UN
(0.95…2.5) UN
DC
(0.32...0.65) UN
(0.32...0.65) UN
W
0.17
0.17
DC
0.05 UN
0.05 UN
Energy-saving mode (–40...+85)°C
Operating range for 1s
Holding voltage range
Minimum holding power
Must drop-out voltage
X-2013, www.findernet.com
Technical data
Mechanical life
cycles
1 · 106
1 · 106
Electrical life at rated load AC7a
cycles
30 · 103
30 · 103
35/4
35/4
–40...+70 (–40...+85)
–40...+70 (–40...+85)
RTII
RTII
Operate/release time
ms
Ambient temperature range (energy-saving mode) °C
Environmental protection
Approvals (according to type)
1
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
67
SERIES
67 Series - Solar relay 50 A
Plug-in / PCB Relays
Features
67.22-4500
67.23-4500
Printed circuit mount - 5.2 mm contact gap
50 A Power relay for photovoltaic inverters
2 and 3 pole versions
(NO double break contacts)
• Contact gap ≥ 5.2 mm (according to
VDE 0126-1-1, EN 62109-1, EN 62109-2)
• Suitable for inverters with DC input up to
1,500 V and AC output up to 690 V,
installations up to 4,000 m above sea level
• DC coils, with only 170 mW holding power
• Reinforced insulation between coil and contacts
• 1.5 mm gap between PCB and relay base
• Suitable for use at ambient temperatures up to
85 °C (with energy-saving coil energization)
or 60 °C (with standard coil energization)
•
For outline drawing see page 6
•2
NO
•3
• Contact
gap ≥ 5.2 mm
• PCB mount
NO
• Contact
• PCB
gap ≥ 5.2 mm
mount
Copper side view
Copper side view
2 NO (DPST-NO)
3 NO (3PST-NO)
≥ 5.2
≥ 5.2
Contact specification
Contact configuration
Contact gap
mm
Rated current/Maximum peak current (for 5 ms) A
50/150
50/150
Rated voltage/Maximum switching voltage V AC
400/690
400/690
Rated load AC1/AC7a (per pole)
VA
20,000
20,000
Rated load AC15 (per pole @ 230 V AC)
VA
2,300
2,300
Single-phase motor rating (230 V AC)
kW
2
2
Three-phase motor rating (480 V AC)
kW
—
7
Breaking capacity DC1: 24/110/220
Minimum switching load
A
mW (V/mA)
Standard contact material
50/7/2
50/7/2
1,000 (10/10)
1,000 (10/10)
AgSnO2
AgSnO2
Coil specification
Nominal voltage (UN)
Rated power
Operating range (–40…+60°C)
V DC
5 - 6 - 8 - 12 - 24 - 48 - 60 - 110
W
2.7
2.7
DC
(0.90 …1.1) UN
(0.90 …1.1) UN
(0.95…2.5) UN
(0.95…2.5) UN
DC
(0.25...0.5) UN
(0.25...0.5) UN
W
0.17
0.17
DC
0.05 UN
0.05 UN
Energy-saving mode (–40...+85)°C
Operating range for 1s
Holding voltage range
Minimum holding power
Must drop-out voltage
Mechanical life
cycles
1 · 106
1 · 106
Electrical life at rated load AC7a
cycles
30 · 103
30 · 103
Operate/release time
ms
Ambient temperature range (energy-saving mode) °C
Environmental protection
Approvals (according to type)
30/4
30/4
–40...+60 (–40...+85)
–40...+60 (–40...+85)
RTII
RTII
X-2013, www.findernet.com
Technical data
2
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
67
SERIES
67 Series - Solar relay 50 A
Ordering information
6 7 . 2
A
B
C
D
3 . 9 . 0 1 2 . 4
3
0
0
Series
Type
2= Single PCB terminals, 1.5 mm gap
between PCB and relay base
No. of poles
2 = 2 pole
3 = 3 pole
A: Contact material
4 = Standard AgSnO2
D: Special versions
0 = Standard
B: Contact circuit
3 = NO, ≥ 3 mm contact gap
5 = NO, ≥ 5.2 mm contact gap
C: Options
0 = None
Plug-in / PCB Relays
Example: 67 series solar relay, single PCB terminals, 2 pole NO, ≥ 3 mm contact gap .
Coil version
9 = DC
Coil voltage
See coil specifications
Technical data
Insulation according to EN 61810-1
Nominal voltage of supply system
V AC
400/690 3-phase
400 1-phase
230/400
Rated insulation voltage
V AC
630
400
400
Pollution degree
3
Insulation between coil and contact set
Type of Insulation
Reinforced
Overvoltage category
III
Rated impulse voltage
kV (1.2/50 μs)
Dielectric strength
V AC
6
4,000
Insulation between adjacent contacts
Type of Insulation
Basic
Overvoltage category
III
Rated impulse voltage
kV (1.2/50) μs
Dielectric strength
V AC
6
2,500
Insulation between open contacts
Type of disconnection
Micro-disconnection *
Full-disconnection
Overvoltage category
—
III
—
4
Rated impulse voltage
kV (1.2/50) μs
Dielectric strength
V AC
2,500 (67.xx-4300) / 3,000 (67.xx-4500)
Other data
Power lost to the environment
without contact current
W
1.7 (67.xx-4300) / 2.7 (67.xx-4500)
with rated current
W
8.5 (67.xx-4300) / 9.5 (67.xx-4500)
Recommended distance between relays mounted on PCB
mm
≥ 20
X-2013, www.findernet.com
* with overvoltage category II: Full-disconnection
3
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
67
SERIES
67 Series - Solar relay 50 A
Contact specification
Cycles
Plug-in / PCB Relays
F 67 - Electrical life vs contact current (AC1/AC7a load)
H 67 - Maximum DC breaking capacity (67.xx-4500)
DC breaking current (A)
DC breaking current (A)
H 67 - Maximum DC breaking capacity (67.xx-4300)
DC voltage (V)
When switching a resistive (DC1) or inductive (DC13) load
having voltage and current values under the corresponding curve,
an electrical life of > 30 000 cycles can be expected.
X-2013, www.findernet.com
When switching a resistive (DC1) or inductive (DC13) load
having voltage and current values under the corresponding curve,
an electrical life of > 30 000 cycles can be expected.
DC voltage (V)
4
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
67
SERIES
67 Series - Solar relay 50 A
Coil specifications
DC coil data, 67.xx-4300
UN
V
5
6
8
12
24
48
60
110
Coil
code
Operating range
(@ 70 °C max)
Holding
voltage
9.005
9.006
9.008
9.012
9.024
9.048
9.060
9.110
Umin
V
4.5
5.4
7.2
10.8
21.6
43.2
54
99
Uh
V
1.6
1.9
2.6
3.8
7.7
15.4
19.2
35.2
Umax
V
5.5
6.6
8.8
13.2
26.4
52.8
66
121
Resistance Rated coil
consumption
I at UN
R
IN
Ω
mA
14.7
340
21.5
279
37.6
213
85
141
340
71
1,355
35
2,120
28
7,120
15
Plug-in / PCB Relays
Nominal
voltage
DC coil data, 67.xx-4500
Nominal
voltage
X-2013, www.findernet.com
UN
V
5
6
8
12
24
48
60
110
Coil
code
Operating range
(@ 60 °C max)
Holding
voltage
9.005
9.006
9.008
9.012
9.024
9.048
9.060
9.110
Umin
V
4.5
5.4
7.2
10.8
21.6
43.2
54
99
Uh
V
1.25
1.5
2
3
6
12
15
27.5
Umax
V
5.5
6.6
8.8
13.2
26.4
52.8
66
121
Resistance Rated coil
consumption
I at UN
R
IN
Ω
mA
9.3
538
13.5
444
23.7
338
53.5
224
213
113
855
56
1,335
45
4,500
24
R 67 - Operating range v ambient temperature, 67.xx-4300
with standard (continuous) coil energization (–40...+70)°C
R 67 - Operating range v ambient temperature, 67.xx-4500
with standard (continuous) coil energization (–40...+60)°C
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
Energy saving mode
In some applications, such as photovoltaic inverters, it may be necessary
to minimize the overall relay power dissipation and to permit use at higher
ambient temperature levels (up to 85 °C). This can be achieved by initially
applying a coil voltage within the Energy saving mode Operating range
(see diagram to the right) and then rapidly (< 1 s) reducing the coil
voltage to a level within the Holding voltage range. The lower the Holding
voltage, the lower is the continuous power dissipation of the coil (0.17 W
minimum).
Coil voltages as high as 2.5UN may be used, when necessary, to reduce
the contact operate time.
R 67 - Operating range v ambient temperature, 67.xx-4300/4500
in energy saving mode (–40...+85)°C
Operating range for < 1 s
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
5
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
67
SERIES
67 Series - Solar relay 50 A
Outline drawings
Type 67.23
X-2013, www.findernet.com
Plug-in / PCB Relays
Type 67.22
6
Courtesy of Steven Engineering, Inc. - 230 Ryan Way, South San Francisco, CA 94080-5370 - Main Office: (650) 588-9200 - Outside Local Area: (800) 258-9200 - www.stevenengineering.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement