B199A
ACME ENGINEERING &
MANUFACTURING CORP.
CONTROLS
LC - 7
P.O. Box 978
Muskogee, OK 74402
Phone: 918/682-7791
Fax: 800/382-2263
[email protected]
KOOLMASTER®
Model LC - 7
LIGHT CONTROL
2 ZONE
3500 WATTS PER ZONE
Acme's LC - 7 provides control of two zones of lights with state of the art technology.
APPLICATION
BENEFITS
•
•
•
•
•
CONTROLLED LIGHT ENVIRONMENTS
SPLIT SYSTEMS - ONE OR TWO ZONES
RUGGED LONG LIFE
EASY TO RUN
EASY TO INSTALL
FEATURES
•
•
•
2 ZONES
7000 WATTS TOTAL
MANUAL OR AUTOMATIC OPERATION
•
•
•
SEALED PLASTIC BOX
120 VAC 60 HZ OPERATION
0 TO 10 VOLT INPUT
DESCRIPTION
The LC – 7 is an electronic device which controls
the light intensity. The light intensity can be
controlled manually by using a dimmer control, or
automatically according to a 0 – 10 VDC signal.
Power wiring is provided to facilitate the
installation. Oversized heat sinks are used to
ensure long-term reliable operation. Waterproof
switches are provided to allow for selection of
automatic, manual, or off control. The output
may be selected for Zone 1, Zone 2, or Zone 1
and Zone 2 operation. Each output or Zone is
capable of supplying up to 3500 watts of 120
VAC light power. In manual operation, the
intensity is controlled by a turn of the knob.
The unit is supplied in a gasketed plastic
enclosure.
EVAPORATIVE
COOLING SYSTEMS
AIR INLETS
DIRECT FIRED
INFRARED
HEATERS
LIGHT TRAPS
CONTROLS
PROPELLER
WALL FANS
CURTAIN MACHINES
SUPPLY AIR FANS
SHUTTERS
ECONOMY
GALVANIZED FANS
PLASTIC/FIBERGLASS
FANS
HORIZONTAL AIR
FLOW FANS
LIMITED WARRANTY Acme Engineering
and Manufacturing Corporation extends this
limited warranty to the original buyer and warrants that products supplied by the Company
shall be free from original defects in workmanship and materials for two years from
date of shipment (except for Acme’s exclusive
duplex split pillow block bearings and shaft 5
years from shipment, belts one year from
shipment, and polyethylene tubing at 90 days
from shipping), provided same have been
properly handled, stored, installed, serviced,
maintained and operated. Refer to Form
MS149 for complete limited warranty terms
and conditions.
WARNING Acme products are designed and
manufactured to provide reliable performance but they are not guaranteed to be
100% free of defects. Even reliable products
will experience occasional failures and this
possibility should be recognized by the User.
If these products are used in a life support
ventilation system where failure could result in
loss or injury, the User should provide adequate back-up ventilation, supplementary
natural ventilation or failure alarm system, or
acknowledge willingness to accept the risk of
such loss or injury.
WARNING DO NOT use in HAZARDOUS
ENVIRONMENTS where fan’s electrical sys-
ACME ENGINEERING &
MANUFACTURING CORP.
P.O. Box 978, Muskogee, Oklahoma 74402
Telephone: 918-682-7791
Fax: 918-682-0134
www.acmeag.com e-mail: [email protected]
www.acmehort.com e-mail: [email protected]
tem could provide ignition to combustible or
flammable materials unless unit is specifically
built for hazardous environments.
CAUTION Guards must be installed when fan
is within reach of personnel or within seven (7)
feet (2.134 m) of working level or when
deemed advisable for safety.
DISCLAIMER The Company has made a diligent effort to illustrate and describe the products in this literature accurately; however, such
illustrations and descriptions are for the sole
purpose of identification, and do not express or
imply a warranty that the products are merchantable, or fit for a particular purpose, or that
the products will necessarily conform to the illustrations or descriptions or dimension.
Member Air Movement and Control Association
March 2003
Form B199A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement