Delta AP300 Instruction manual

Add to my manuals
16 Pages

advertisement

Delta AP300 Instruction manual | Manualzz

Portable Single-Stage

Dust Collector

(Model AP300)

PART NO. 905588 - 05-13-02

Copyright © 2002 Delta Machinery

To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com.

For Parts, Service, Warranty or other Assistance,

ESPAÑOL: PÁGINA 17 please call

1-800-223-7278 (

In Canada call

1-800-463-3582).

GENERAL SAFETY RULES

Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust masks and hearing protection can reduce your potential for injury. But even the best guard won’t make up for poor judgment, carelessness or inattention. Always use common sense and exercise caution in the workshop.

If a procedure feels dangerous, don’t try it. Figure out an alternative procedure that feels safer. REMEMBER: Your personal safety is your responsibility.

This machine was designed for certain applications only. Delta Machinery strongly recommends that this machine not be modified and/or used for any application other than that for which it was designed. If you have any questions relative to a particular application, DO NOT use the machine until you have first contacted Delta to determine if it can or should be performed on the product.

Technical Service Manager

Delta Machinery

4825 Highway 45 North

Jackson, TN 38305

(IN CANADA: 505 SOUTHGATE DRIVE, GUELPH, ONTARIO N1H 6M7)

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY

1. FOR YOUR OWN SAFETY, READ INSTRUCTION

MANUAL BEFORE OPERATING THE TOOL. Learn the tool’s application and limitations as well as the specific hazards peculiar to it.

2. KEEP GUARDS IN PLACE and in working order.

3. ALWAYS WEAR EYE PROTECTION. Wear safety glasses. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses. Also use face or dust mask if cutting operation is dusty. These safety glasses must conform to ANSI Z87.1 requirements. NOTE:

Approved glasses have Z87 printed or stamped on them.

4. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it “on”.

5. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

6. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose them to rain. Keep work area well-lighted.

7. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area.

8. MAKE WORKSHOP CHILDPROOF – with padlocks, master switches, or by removing starter keys.

9. DON’T FORCE TOOL. It will do the job better and be safer at the rate for which it was designed.

10. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.

11. WEAR PROPER APPAREL. No loose clothing, gloves, neckties, rings, bracelets, or other jewelry to get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.

12. SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and frees both hands to operate tool.

13. DON’T OVERREACH. Keep proper footing and balance at all times.

14. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

15. DISCONNECT TOOLS before servicing and when changing accessories such as blades, bits, cutters, etc.

16. USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by Delta may cause hazards or risk of injury to persons.

17. REDUCE THE RISK OF UNINTENTIONAL STARTING.

Make sure switch is in “OFF” position before plugging in power cord. In the event of a power failure, move switch to the “OFF” position.

18. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted.

19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function – check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don’t leave tool until it comes to a complete stop.

22.

STAY ALERT, WATCH WHAT YOU ARE DOING, AND

USE COMMON SENSE WHEN OPERATING A POWER

TOOL. DO NOT USE TOOL WHILE TIRED OR UNDER

THE INFLUENCE OF DRUGS, ALCOHOL, OR

MEDICATION. A moment of inattention while operating power tools may result in serious personal injury.

23. MAKE SURE TOOL IS DISCONNECTED FROM

P O W E R S U P P LY w h i l e m o t o r i s b e i n g m o u n t e d , connected or reconnected.

24. THE DUST GENERATED by certain woods and wood products can be injurious to your health. Always operate machinery in well ventilated areas and provide for proper dust removal. Use wood dust collection systems whenever possible.

2

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

ADDITIONAL SAFETY RULES FOR

DUST COLLECTORS

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1.

DO NOT OPERATE THIS MACHINE until it is

assembled and installed according to the instructions.

2.

OBTAIN ADVICE FROM YOUR SUPERVISOR,

instructor, or another qualified person if you are not familiar with the operation of this machine.

3.

FOLLOW ALL WIRING CODES and recommended electrical connections.

4.

DO NOT leave the dust collector plugged into the electrical outlet. Unplug dust collector from the outlet when not in use and before servicing, changing bags, unclogging and cleaning.

5.

ALWAYS turn all controls “OFF” before unplugging the dust collector.

6.

TO REDUCE THE RISK OF ELECTRICAL SHOCK, do not use on wet surfaces. Do not expose to rain. Store indoors.

7.

DO NOT use the dust collector to pick up flammable or combustible liquids, such as gasoline.

NEVER use the dust collector near any flammable or combustible liquids.

8.

USE the dust collector to pick up wood materials only. DO NOT use the dust collector to pick up metal shavings, metal dust, or metal parts.

9.

NEVER use the dust collector to dissipate fumes or smoke. NEVER pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.

10. DO NOT pull the dust collector by the power cord.

NEVER allow the power cord to come in contact with sharp edges, hot surfaces, oil or grease. Do not place anything over the top of the power cord.

11. DO NOT unplug the dust collector by pulling on the power cord. ALWAYS grasp the plug, not the cord.

12. DO NOT handle the plug or dust collector with wet hands.

13. REPLACE a damaged cord immediately. DO NOT use a damaged cord or plug. If the dust collector is not operating properly, or has been damaged, left outdoors or has been in contact with water, take it to an

Authorized Service Center for service.

14. DO NOT use the dust collector as a toy. DO NOT use near or around children.

15. DO NOT insert fingers or foreign objects into the dust intake port or discharge port. Keep hair, loose clothing, fingers, and all body parts away from openings and moving parts of the dust collector.

16. DO NOT use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.

17. NEVER use the dust collector without the dust collection bag in place and properly secured.

18. ALWAYS use intake cover to cover dust port when the dust collector is not in use or mounted to a supporting surface for storage.

19. PERIODICALLY INSPECT dust bag for any cuts, rips or tears. NEVER operate the dust collector with a damaged bag or vacuum hose.

20. USE EXTRA CARE when cleaning on stairs.

21. TURN THE MACHINE “OFF” AND DISCONNECT

THE MACHINE from the power source before installing or removing accessories, before adjusting or changing set-ups, or when making repairs.

22. TURN THE MACHINE “OFF”, disconnect the machine from the power source, and clean the table/work area before leaving the machine. LOCK THE

SWITCH IN THE “OFF” POSITION to prevent unauthorized use.

23. ADDITIONAL INFORMATION regarding the safe and proper operation of this tool is available from the

Power Tool Institute, 1300 Summer Avenue, Cleveland,

OH 44115-2851. Information is also available from the

National Safety Council, 1121 Spring Lake Drive, Itasca,

IL 60143-3201. Please refer to the American National

Standards Institute ANSI 01.1 Safety Requirements for

Woodworking Machines and the U.S. Department of

Labor OSHA 1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

3

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the motor to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage will damage the motor.

WARNING: DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

MOTOR SPECIFICATIONS

Your machine is wired for 120 volt, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

WARNING: THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM

ELECTRIC SHOCK.

1. All grounded, cord-connected machines:

2. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with an electric cord having an equipmentgrounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipmentgrounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the machine will have a grounding plug that looks like the plug illustrated in Fig. A. A temporary adapter, which looks like the adapter illustrated in Fig. B, may be used to connect this plug to a matching 2-conductor receptacle as shown in Fig. B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician.

The green-colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. Whenever the adapter is used, it must be held in place with a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.

Check with a qualified electrician or service personnel if t h e g r o u n d i n g i n s t r u c t i o n s a r e n o t c o m p l e t e l y understood, or if in doubt as to whether the machine is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in

Fig. A.

Repair or replace damaged or worn cord immediately.

240 VOLT,

SINGLE PHASE OPERATION

The motor supplied with your dust collector is a dual voltage 120/240 volt motor. The dust collector motor is shipped ready-to-run for 120 volt operation; however, it may be converted for 240 volt operation.

The conversion of your dust collector for 240 volt operation must be done by qualified electrical personnel. Should you desire to have your dust collector converted for 240 volts, take your dust collector to your local Authorized Delta

Service Center. Call 1-800-223-7278 for the location of the

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDED OUTLET BOX

GROUNDING

MEANS

ADAPTER

GROUNDING BLADE

IS LONGEST OF THE 3 BLADES

Fig. A

4

Fig. B

nearest Authorized Service Center. The Service Center will be able to convert your dust collector for 240 volts by (a) re-wiring the motor for 240 volts; (b) installing a 240 volt attachment plug to the power supply cord; and (c) replacing the single pole on/off switch shipped with your dust collector with a double pole switch.

The dust collector with a 240 volt plug should only be connected to an outlet having the same configuration as the plug illustrated in Fig. C. No adapter is available or should be used with the 240 volt plug.

WARNING: IN ALL CASES, MAKE CERTAIN THE

RECEPTACLE IN QUESTION IS PROPERLY

G R O U N D E D . I F Y O U A R E N O T S U R E H AV E A

Q U A L I F I E D E L E C T R I C I A N C H E C K T H E

RECEPTACLE.

GROUNDED OUTLET BOX

CURRENT CARRYING PRONGS

240 VOLT

GROUND PRONG

Fig. C

EXTENSION CORDS

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D, shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere

Rating Volts

Total Length of Cord in Feet

Gauge of

Extension Cord

0-6

0-6

0-6

0-6

6-10

6-10

6-10

6-10

10-12

10-12

10-12

10-12

12-16

12-16

12-16

115

115

115

115

115

115

115

115

115

115

115

115

115

115

115 up to 25

25-50

50-100

100-150 up to 25

25-50

50-100

100-150

18 AWG

16 AWG

16 AWG

14 AWG

18 AWG

16 AWG

14 AWG

12 AWG up to 25

25-50

50-100

100-150

16 AWG

16 AWG

14 AWG

12 AWG up to 25

25-50

14 AWG

12 AWG

GREATER THAN 50 FEET NOT RECOMMENDED

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere

Rating Volts

Total Length of Cord in Feet

Gauge of

Extension Cord

0-6

0-6

0-6

0-6

6-10

6-10

6-10

6-10

10-12

10-12

10-12

10-12

12-16

12-16

12-16

230

230

230

230

230

230

230

230

230

230

230

230

230

230

230 up to 50

50-100

100-200

200-300 up to 50

50-100

100-200

200-300

18 AWG

16 AWG

16 AWG

14 AWG

18 AWG

16 AWG

14 AWG

12 AWG up to 50

50-100

100-200

200-300

16 AWG

16 AWG

14 AWG

12 AWG up to 50

50-100

14 AWG

12 AWG

GREATER THAN 100 FEET NOT RECOMMENDED

Fig. D Fig. D

OPERATING INSTRUCTIONS

FOREWORD

The Delta ShopMaster Model AP300 is a portable single stage dust collector.

UNPACKING AND CLEANING

Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax.

NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT

PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE

ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR

ACCESSORIES AND MAY BE INTENDED TO ILLUSTRATE TECHNIQUE ONLY.

5

DUST COLLECTOR PARTS

6

2

3

1

4

5

1.

Dust collector

2.

Hose

3.

Dust bag

4.

Exhaust flange

5.

Exhaust flange gasket

6.

Intake funnel

7.

Intake support angle brace

8.

Upper support bracket

9.

Lower tube support

9

7

8

12

14

15

16

11

17

13

18

10

Fig. 2

10. Wheel casters (4)

11. Lower tube support clamps (2)

12. Adjustable locking lever

13. Hose clamps (2)

14. 5/16-18x5/8" Button head carriage bolt (2)

15. 5/16" lockwasher (3)

16. 5/16-18 Hex nut (6)

17. 5/16-18x5/8" Hex head screw (4)

18. Intake cap

6

ASSEMBLY

WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE TOOL TO THE POWER SOURCE UNTIL THE

MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION

MANUAL.

WHEEL CASTERS

1.

Remove the 3/8-16 hex nut and 3/8" lockwasher from each of the four wheel casters.

2.

Place the dust collector on its side.

3.

Insert bolt on wheel caster through the four holes (A)

Fig. 3 in the base of the dust collector.

4.

Place a 3/8" lockwasher (A) Fig. 4 onto each bolt.

5.

Thread a 3/8-16 hex nut (B) Fig. 4 onto each of the four bolt heads and tighten securely.

A

Fig. 3

B

A

Fig. 4

EXHAUST FLANGE

1.

Align the holes in the exhaust flange (A) Fig. 5 with the holes in the exhaust flange gasket (B).

2.

Insert a 5/16-18x5/8" hex head bolt thru the exhaust flange, exhaust flange gasket and the base unit as shown in Fig. 6.

3.

Thread a 5/16-18 hex nut (B) onto the 5/16-18x5/8" hex head bolt (A) Fig. 6 and tighten securely.

4.

Repeat this process for the three remaining bolts.

B

A

Fig. 5

B

A

Fig. 6

7

DUST PORT TUBE AND

CONNECTOR TO DUST

COLLECTOR BODY

1.

Place tube clamp (A) Fig. 7 on the lower support tube holder (B).

2.

Insert the lower tube support (A) into the tube support holder (B) as shown in Fig. 8.

Fig. 7

A

B

3.

Place a tube clamp (A) onto the lower tube support as shown in Fig. 9.

Fig. 8

A

Fig. 9

A

B

8

4.

Align the two holes in the intake support angle brace

(A) Fig. 10 with the two holes in the intake funnel (B).

5.

Fasten the intake support angle brace to the intake funnel by inserting the two 5/16-18x5/8" button head carriage bolts (C) thru the intake funnel (B) and the intake support angle brace (A) as shown in Fig. 11.

6.

Place a 5/16" lockwasher (A) Fig. 12,onto the bolt

(B), and thread a 5/16-18" hex nut (C) onto the bolt (B) and tighten securely.

7.

Attach the upper support bracket (B) Fig. 13 to the intake support angle brace (C) with the adjustable locking lever (D). NOTE: PLACE A 5/16”

LOCKWASHER (E) FIG. 13, ONTO LOCKING LEVER

SCREW BEFORE ATTACHING TO THE INTAKE

SUPPORT ANGLE BRACE.

A

Fig. 10

B

A

B

Fig. 11

C

D

Fig. 12

C

A

B

E

C

B

Fig. 13

9

8.

Place intake funnel assembly (A), onto lower support tube (B) Fig. 14, and secure with tube clamp (C).

C

B

A

Fig. 14

VACUUM HOSE TO

DUST COLLECTOR

1.

Place the intake cap holder (D) on the dust collector as shown in Fig. 15. NOTE: DO NOT COVER THE

INTAKE PORT WITH THE INTAKE CAP WHEN

ATTACHING THE HOSE TO THE INTAKE PORT.

2.

Place hose clamp (A) Fig. 15, onto one end of vacuum hose (B) and slide hose around intake port (C) as shown in Fig. 16. Tighten hose clamp (A).

B

C

Fig. 15

A

D

C

A

Fig. 16

10

3.

Place the remaining hose clamp (A) Fig. 17, around the other end of hose (B), slide hose (B) onto intake funnel (C), and tighten hose clamp (A). NOTE: If desired, intake funnel (C) can be rotated to the vertical position, as shown in Fig. 18.

A

Fig. 17

C

B

C

Fig. 18

DUST BAG TO DUST

COLLECTOR

Loosely thread end of dust bag strap (A) through clamp

(B) as shown in Fig. 19. Place open end of dust bag (C)

Fig. 19, over outlet flange (D) Fig. 20 and firmly pull strap

(A) to fasten dust collection bag to outlet flange.

A

A

B

Fig. 19

C

D

Fig. 20

11

OPERATING CONTROLS & ADJUSTMENTS

WARNING: FOR OPERATOR SAFETY, MAKE CERTAIN

THE DUST INTAKE PORT IS COVERED WITH THE HOSE

BEFORE OPERATING THE MACHINE. THE ROTATING FAN

INSIDE THE BLOWER HOUSING IS ACCESSIBLE

THROUGH THE DUST INTAKE PORT AND IS HAZARDOUS.

MAKE SURE INTAKE CAP COVERS THE INTAKE PORT

WHEN HOSE IS REMOVED. ALWAYS WEAR PROPER

APPAREL. DO NOT WEAR JEWELRY, AND KEEP FINGERS

AND ALL FOREIGN OBJECTS OUT OF THE DUST INTAKE

PORT. ALWAYS FOLLOW THE SAFETY RULES OF THIS

MANUAL.

STARTING AND STOPPING

DUST COLLECTOR

The ON/OFF switch (A) Fig. 24, is located on the side of the motor. To turn the machine “ON” move the switch up to the “ON” position. To turn the machine “OFF” move the switch down to the “OFF” position..

A

Fig. 24

LOCKING SWITCH IN

THE “OFF” POSITION

IMPORTANT: When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use. This can be done by grasping the switch toggle (B) Fig. 25, and pulling it out of the switch as shown. With the switch toggle (B) removed, the switch will not operate. However, should the switch toggle be removed while the machine is running, it can be turned “OFF” once, but cannot be restarted without inserting the switch toggle (B).

B

Fig. 25

12

OPERATIONS

This versatile dust collector is light, compact and can easily be transported for use in and out of the workshop.

This dust collector can be used with many different types of woodworking machinery as shown in Figs. 26,

27, and 28. .

Fig. 26 illustrates the dust collector used with a router.

Note that the intake port is adjusted so that dust created by the router will be collected.

Fig. 27 illustrates the dust collector used with a table saw. Note that the intake port is removed from the lower tube support. The intake funnel can be clamped to a tool as shown.

Fig. 26

Fig. 28 illustrates the dust collector used with a drum sander that is equipped with a dust removal port. The 4" hose can be connected directly to the dust removal port.

Fig. 27

13

Fig. 28

TRANSPORTATION AND

STORAGE

1.

The dust collector features a convenient carrying handle with rubber grip (A) Fig. 29, which allows the unit to be carried easily from one job area to another.

IMPORTANT: THE DUST COLLECTOR WEIGHS

APPROXIMATELY 46 LBS. CARE SHOULD BE TAKEN

WHEN LIFTING AND TRANSPORTING THE MACHINE.

2.

In addition to the carrying handle, the machine features a storage mounting bracket (B) Fig. 30, with a hole for mounting the dust collector to a wall or wooden support when not in use.

Fig. 29

A

B

Fig. 30

MAINTENANCE

WARNING: Before any maintenance or service is performed, be sure the dust collector is disconnected from the power source to prevent accidental starting. All maintenance other than the items recommended in this manual should be performed by an authorized Delta Service Center.

1.

WARNING: Always disconnect the machine from the power source before performing any maintenance procedures.

2.

The condition of the dust bag should be checked periodically for damage and emptied on a regular basis. Do not transport the machine with a full dust bag.

3.

Clean and apply a dry silicone lubricant monthly to the impeller to remove any dirt or build-up of pitch, gum and wood shavings.

4.

WARNING: Always make sure that the intake cap (A) Fig. 31, covers the intake port when the hose is not connected to the machine.

A

Fig. 31

14

NOTES

15

ACCESSORIES

A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our Web Site

www.deltamachinery.com

for a catalog or for the name of your nearest supplier.

WARNING: Since accessories other than those offered by Delta have not been tested with this product, use of such accessories could be hazardous. For safest operation, only

Delta recommended accessories should be used with this product.

PARTS, SERVICE OR WARRANTY ASSISTANCE

All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network of Porter-Cable

Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).

Two Year Limited Warranty

Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. Delta may require that electric motors be returned prepaid to a motor manufacturer’s authorized station for inspection and repair or replacement.

Delta will not be responsible for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for incidental or consequential damages resulting from defective products. This warranty is Delta’s sole warranty and sets forth the customer’s exclusive remedy, with respect to defective products; all other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are expressly disclaimed by Delta.

Printed in U.S.A.

16

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Questions and Answers

What kind of electrical circuit should be used for the machine?
A separate #12 wire circuit protected by a 20 Amp time lag fuse.
What type of extension cord should be used?
3-wire extension cord with 3-prong grounding type plugs.
What should be done before connecting the motor to the power line?
Ensure the switch is in the "OFF" position and the electric current matches the specifications on the machine.
What are the motor specifications for the Delta AP300?
It is wired for 120 volt, 60 HZ alternating current.
Can I use the Delta AP300 in damp locations?
No, the machine should not be exposed to rain or operated in damp locations.
What should I do if the dust collector is not operating properly?
Take it to an Authorized Service Center for service.

Related manuals

Download PDF

advertisement