MODEL: VA Plug-in Signal Conditioners M-UNIT OUTPUT 50 mA OUTPUT TRANSMITTER

MODEL: VA Plug-in Signal Conditioners M-UNIT OUTPUT 50 mA OUTPUT TRANSMITTER
MODEL: VA
Plug-in Signal Conditioners M-UNIT
OUTPUT
Current
10 – 50 mA DC (Load resistance 300 Ω max.)
50 mA OUTPUT TRANSMITTER
(non-isolated)
Functions & Features
• Converting a DC input into a 10 – 50 mA DC signal
• High-density mounting
[2] POWER INPUT
Typical Applications
• Interfacing between 10 – 50 mA and 4 – 20 mA systems
50
(1.97)
80
(3.15)
127
(5)
mm (inch)
AC Power
B: 100 V AC
C: 110 V AC
F: 120 V AC
G: 200 V AC
H: 220 V AC
J: 240 V AC
GENERAL SPECIFICATIONS
Construction: Plug-in
Connection: M3.5 screw terminals
Housing material: Flame-resistant resin (black)
Isolation: Input or output to power
Overrange output: Approx. -10 to +120 % at 100 Ω load
Zero adjustment: -5 to +5 % (front)
Span adjustment: 95 to 105 % (front)
MODEL: VA-[1]-[2]
INPUT SPECIFICATIONS
ORDERING INFORMATION
• Code number: VA-[1]-[2]
Specify a code from below for each [1], [2].
(e.g. VA-6-B)
•Special input range (For codes Z & 0)
[1] INPUT
Current
A: 4 – 20 mA DC (Input resistance 250 Ω)
A1: 4 – 20 mA DC (Input resistance 50 Ω)
B: 2 – 10 mA DC (Input resistance 500 Ω)
C: 1 – 5 mA DC (Input resistance 1000 Ω)
D: 0 – 20 mA DC (Input resistance 50 Ω)
E: 0 – 16 mA DC (Input resistance 62.5 Ω)
F: 0 – 10 mA DC (Input resistance 100 Ω)
G: 0 – 1 mA DC (Input resistance 1000 Ω)
H: 10 – 50 mA DC (Input resistance 100 Ω)
Z: Specify current (See INPUT SPECIFICATIONS)
Voltage
1: 0 – 10 mV DC (Input resistance 10 kΩ min.)
2: 0 – 100 mV DC (Input resistance 100 kΩ min.)
3: 0 – 1 V DC (Input resistance 1 MΩ min.)
4: 0 – 10 V DC (Input resistance 1 MΩ min.)
5: 0 – 5 V DC (Input resistance 1 MΩ min.)
6: 1 – 5 V DC (Input resistance 1 MΩ min.)
4W: -10 – +10 V DC (Input resistance 1 MΩ min.)
0: Specify voltage (See INPUT SPECIFICATIONS)
http://www.m-system.co.jp/
• DC Current:
Shunt resistor attached to the input terminals (0.5 W)
Specify input resistance value for code Z.
• DC Voltage: -300 – +300 V DC
Minimum span: 10 mV
Offset: Max. 1.5 times span
Input resistance
Span 10 – 100 mV : ≥ 10 kΩ
Span 0.1 – 1 V : ≥ 100 kΩ
Span ≥ 1 V : ≥ 1 MΩ
INSTALLATION
Power input
•AC: Operational voltage range: rating ±10 %,
50/60 ±2 Hz, approx. 3 VA
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 400 g (0.88 lbs)
PERFORMANCE in percentage of span
Accuracy: ±0.1 %
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)
Response time: ≤ 0.5 sec. (0 – 90 %)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1000 V AC @ 1 minute
VA SPECIFICATIONS
ES-1316 Rev.4 Page 1/2
MODEL: VA
(input or output to power)
2000 V AC @ 1 minute (input or output or power to ground)
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
CLAMP
(top & bottom)
20
(.79)
7.8 (.31)
5
4
3
7
8
1
2
2–4.5 (.18) dia.
MTG HOLE
15 (.59) deep
8–M3.5
SCREW
50 (1.97)
6
80 (3.15)
80 (3.15)
35.4 (1.39)
DIN RAIL
35mm wide
107 (4.21)
40 (1.57)
127 (5)
[3.3 (.13)]
50 (1.97)
• When mounting, no extra space is needed between units.
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Z
+
R
INPUT
–
3
Low Drift
Amplifier
S
Output
Driver
1 +
OUTPUT
4
2 –
5
7 U
6
8 V
POWER
Base Socket
Input shunt resistor attached for current input.
Specifications are subject to change without notice.
http://www.m-system.co.jp/
VA SPECIFICATIONS
ES-1316 Rev.4 Page 2/2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement