Body (Interior Exterior)

Body (Interior Exterior)
Body (Interior &
Exterior)
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BD - 2
EXTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BD - 7
INTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BD -20
BUMPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BD -33
SEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BD -37
BD -2
BODY (INTERIOR & EXTERIOR)
GENERAL
SPECIFICATIONS
ESTC0010
Hood
Type
Rear hinged, front opening type
Front door
Construction
Front hinged, full door construction
Regulator system
Wire drum type
Locking system
Pin-fork system
Rear door
Construction
Front hinged, full door construction
Regulator system
Single arm type
Locking system
Pin-fork system
Tailgate
Type
Glass thickness mm (in.)
Inner hinged, gas lifter type
Laminated clear, tinted
Windshield glass
5 (0.20)
Front window glass
3.2 (0.13)
Rear fixed glass
3.2 (0.13)
Rear window glass
3.2 (0.13)
Tailgate window glass
3.2 (0.13)
Seat belt
Front and outboard rear side
3 point type with E.L.R. (Emergency Locking Retractor)
Rear center
2 point type with static
GENERAL
TIGHTENING TORQUE
BD -3
ESTC0020
Nm
kg.cm
lb.ft
Strike to body
9-14
90-140
6.5-10
Door hinge to body
34-42
340-420
24.5-30
Door hinge to door
13-26
130-260
9-19
Tailgate hinge to body
7-9
70-90
5-6.5
Tailgate hinge to tailgate
7-9
70-90
5-6.5
Tailgate latch to tailgate
7-11
70-110
5-8
Gas lifter ball joint mounting bolts
22-27
220-270
16-19.5
7-9
70-90
5-6.5
Hood hinge to body
22-27
220-270
16-19.5
Hood hinge to hood
22-27
220-270
16-19.5
Hood latch to body
7-11
70-110
5-8.0
Front seat to floor bolt
35-55
350-550
25.3-40
Front seat mounting nuts
24-36
240-360
18-26
Rear seat back mounting bolts
17-26
170-260
12-19
Rear seat cushion mounting bolts
17-26
170-260
12-19
Front seat belt buckle
40-55
400-550
29-40
Front seat belt upper anchor
40-55
400-550
29-40
Front seat belt retractor to center pillar
40-55
400-550
29-40
Front seat belt height adjuster
40-55
400-550
29-40
Rear seat belt anchor attaching bolt
40-55
400-550
29-40
Rear seat belt retractor mounting bolt
40-55
400-550
29-40
Front and rear doors
Tailgate
Gas lifter mounting bolts
Hood
Seat
Seat belt
BD -4
SPECIAL TOOLS
BODY (INTERIOR & EXTERIOR)
ESTC0040
Tool (Number and name)
Illustration
Use
09793-21000
Door hinge adjusting wrench
Adjustment, removal and installation
of the door hinge
ESDA010A
09800-21000
Ornament remover
Trim removal
ESDA010B
09853-31000
Headliner clip remover
Removal of the headliner clips
ESDA010C
09861-31100
Sealant cut-out tool
Cutting the sealant of the windshield
(use with 09861-31200)
ESDA010D
09861-31200
Sealant cutting blade
Cutting the sealant of the windshield
(use with 09861-31100)
ESDA010E
09861-31300
Sealant gun
BD -6
BODY (INTERIOR & EXTERIOR)
TROUBLESHOOTING
ESTC0060
Symptom
Wind noise around door
Probable cause
Remedy
Weatherstrip not holding firmly
Adjust fit of door
Improperly installed weatherstrip
Repair or replace
Improperly closed door
Adjust
Improperly fitting door
Adjust
Improper clearance between door glass
and division channel
Adjust
Deformed door
Repair or replace
Wind noise
Loose or deformed deflector
Retighten or replace
Door glass fails to operate
up or down
Incorrect window glass installation
Adjust position
Damaged or faulty regulator arm or regulator
Correct or replace
Door does not open or
close completely
Incorrect door installation
Adjust position
Defective door checker
Correct or replace
Door hinge require grease
Apply grease
Striker and latch not properly aligned
Adjust
Incorrect installed hood
Adjust
Incorrect hood bumper height
Adjust
Defective seal
Fill with sealant
Defective flange
Correct
Hood does not open or
close completely
Water leak through
windshield and rear
window
EXTERIOR
BD -7
EXTERIOR
FENDER
COMPONENTS
ESTE0100
Fender
Wheel guard
ESTE010A
BD -8
BODY (INTERIOR & EXTERIOR)
REMOVAL
1.
ESTE0270
Remove the head lamp.
ESTE027A
2.
Remove the wheel guard and side repeater.
ESTE015B
3.
Remove the fender mounting bolts.
NOTE
Be careful not to damage paint.
ESTE015C
4.
Installation is the reverse of removal.
EXTERIOR
BD -9
HOOD
ADJUSTMENT
ESTC0200
HOOD HINGE
1.
Loosen the hood hinge mounting bolt.
2.
Adjust the longitudinal and lateral positions of the
hood by utilizing the holes in the hinge.
3.
Adjust front edge of hood in vertical direction by adjusting the overslam bumpers.
ESTC020A
HOOD LATCH
1.
Loosen the hood latch mounting bolts.
2.
Adjust the alignment of the hood latch by adjusting
the longitudinal and lateral position of the latch, and
by adjusting the height of the hood.
ESTC020B
BD -10
BODY (INTERIOR & EXTERIOR)
TAIL GATE
COMPONENTS
ESTC0250
Tailgate weatherstrip
22-27 (220-270, 16-19.5)
22-27
(220-270,
16-19.5)
Tailgate trim panel
Tailgate lifter
Overslam bumper
17-26 (170-260, 12-19)
Tailgate latch
Tailgate striker
Tailgate release cable
TORQUE : Nm (kg·cm, lb·ft)
ESTC025A
REMOVAL AND INSTALLATION
1.
ESTE0350
Remove the rear wiper arm.
ESTE200A
ESTE030A
2.
Insert a trim panel remover between the trim fasteners
and the tailgate trim panel to pry off.
EXTERIOR
3.
BD -11
From the interior, remove the rear wiper motor.
ADJUSTMENT
1.
ESTC0350
If the striker and latch do not match properly, move
the striker frontward or leftward or rightward.
ESTE035B
4.
Remove the tailgate latch and the key cylinder.
ESTC035A
2.
If the clearance around the tailgate is not even when
the tailgate is closed, move the tailgate hinge frontward or rearward or leftward or rightward.
ESTE035D
5.
Remove the tailgate struts and then loosen the bolts
holding the tailgate hinge.
ESTC035B
ESTE035C
6.
Remove the tailgate.
7.
Installation is the reverse of removal.
BD -12
BODY (INTERIOR & EXTERIOR)
FRONT DOOR
COMPONENTS
ESTC0400
Front door glass
Door window glass run
Inside belt weatherstrip
Door checker
Door inside handle
Door striker
Door inside handle rod
Door outside handle
Door striker shim
Map pocket
Door latch
Door trim
Door window regulator
Power window regulator motor
Door window regulator handle
BD -14
9.
BODY (INTERIOR & EXTERIOR)
Remove the window glass.
13. Remove the front safety lock rod and inside handle
rod.
14. Remove the door latch and lock actuator and the front
door outside handle.
ESTC045E
10. Remove the front door belt outside weatherstrip.
A-A
ESTC045H
15. Installation is the reverse of removal. When installing
the door trim seal, butyl tape sould not be placed over
the door trim fastener mounting area.
A
B
B
A
B-B
ESTC045F
11. Remove the door regulator channel mounting bolts
and then remove the door regulator assembly.
ESTC045G
12. Remove the window glass run.
ESDA065K
EXTERIOR
ADJUSTMENT
BD -15
GLASS
ESTC0500
DOOR POSITION
Check for a flush fit with the body, then check for an equal
gap between the front and rear, and top and bottom door
edges and body.
The door and body edges should also be parallel. Adjust
at the hinge with the Special Tool (09793-21000).
CAUTION
Attach protective tape to the fender edges where
the hinge is installed.
09793-21000
ESTC050A
DOOR STRIKER
Make sure the door is not loose and that it latches securely
without slamming. If necessary, adjust the door as follows:
1.
Draw a line around the striker plate for reference.
2.
Loosen the striker screws, and move the striker IN or
OUT to make the latch fit tighter or looser. Move the
striker UP or DOWN to align it with the latch opening.
Then lightly tighten the screws and recheck.
ESTC050B
NOTE
Hold the outside handle out and push the door against
the body to ensure the striker allows a flush fit.
If the glass does not fit evenly when closed, adjust the slant
of the glass in the front-to-back direction.
BD -16
BODY (INTERIOR & EXTERIOR)
REAR DOOR
COMPONENTS
ESTC0550
Door fixed glass weatherstrip
Door window glass run
Door fixed glass
Door division channel
Door glass
Door window regulator
Door window regulator handle
Door trim panel
Door pull handle
ESTC055A
EXTERIOR
REMOVAL AND INSTALLATION
1.
BD -17
4.
ESTC0600
Insert a trim remover between the trim fasteners and
the door panel to pry off.
Using a piece of cloth, remove the door window regulator handle. (Manual type only)
ESHA020D
ESDA065L
2.
5.
Remove the door trim seal and lower the window
glass.
Remove the door pull handle and inside handle.
ESTC060C
ESTC060A
3.
6.
Remove the door window regulator.
Remove the safety lock rod knob.
ESTC060D
ESTC060B
7.
Remove the door belt outside weatherstrip.
ESTC060E
BD -18
8.
BODY (INTERIOR & EXTERIOR)
Loosen the door division channel mounting bolts and
screw, and remove the rear door fixed glass.
ESTC060F
9.
Remove the door glass and door division channel.
ESTC060G
10. Remove the door glass run.
ESTC060H
11. Installation is the reverse of removal.
When installing the door trim seal, butyl tape should
not be placed over the door trim fastener mounting
area.
EXTERIOR
BD -19
BODY SIDE MOLDINGS
REMOVAL AND INSTALLATION
ESDA1100
WAISTLINE MOLDING
1.
Beginning from either end, remove the waistline molding using Special Tool (09800-21000) from the front
and rear doors.
NOTE
Take care not to scratch or bend the door moldings.
ESDA110A
ROOF MOLDING
1.
Pry up the roof molding with a flat tip screwdriver as
shown in the illustration.
ESDA110B
NOTE
When prying with a flat tip screwdriver, wrap it with
protective tape to prevent damage.
Take care not to scratch the body and roof molding
use protective tape on the body.
2.
Pull the roof molding up, then remove the roof molding.
3.
Installation is the reverse of the removal.
NOTE
If necessary, replace any damaged clips.
BD -20
BODY (INTERIOR & EXTERIOR)
INTERIOR
CONSOLE
COMPONENTS
ESTC0650
Floor console
Shift lever boot
ESTC065A
REMOVAL AND INSTALLATION
1.
ESTC0700
Loosen the tapping screws.
ESTC070A
2.
Loosen the gear shift knob and remove the floor console.
3.
Installation is the reverse of removal.
INTERIOR
BD -21
CRASH PAD
COMPONENTS
ESTC0750
Crash pad
Center facia panel
Steering column shroud
Cluster facia panel
ESTC075A
BD -22
BODY (INTERIOR & EXTERIOR)
REMOVAL AND INSTALLATION
5.
ESTC0800
1.
Disconnect the negative(-) battery terminal.
2.
Remove the airbag module or horn pad and steering
wheel.
Remove the scuff trim and lower trim.
CAUTION
For instructions on the removal of the air bag
module, refer to the RT section.
ESTC080H
6.
Remove the front pillar trim.
ESTC080A
3.
Remove the steering column shrouds and multifunction switch.
ESTC080I
7.
Remove the cluster and disconnect the speedometer
cable.
1)
Loosen the speedometer cable in the engine
room compartment
ESTC080C
4.
Remove the center facia panel and audio.
ESTC080K
ESTC080F
INTERIOR
2)
BD -23
Disconnect the speedometer cable in the crash
pad.
ESTC080J
8.
Remove the crash pad mounting bolts and disconnect
the connectors.
ESTC080L
9.
Installation is the reverse of removal.
BD -24
BODY (INTERIOR & EXTERIOR)
WINDSHIELD GLASS
COMPONENTS
ESTC0850
A
A
"Z"
B
B
1.
2.
3.
4.
Windshield glass
Windshield glass dam
Windshield glass spacer
Windshield glass moulding
3
SECT B-B
SECT A-A
2
2
4
4
1
DETAIL "Z"
ESTC085A
INTERIOR
BD -25
WORKING PROCESS
ESTC0900
Window glass installation procedure
Body side
Body side
Reusing the glass
Replacing the glass
Cleaning of adhesion surface
Cut off the residual adhesive
until the thickness is less than
2mm. Clean the adhesion surface
with isopropyl alcohol, and let dry
for 3 minutes or more.
Cleaning of adhesion surface
Completely cut off all of the
residual adhesiv. Clean the
adhesion surface with isopropyl
alcohol, and let dry for 3
minutes or more.
Cleaning of adhesion surface
Clean off any dirt adhering to the
adhesion surface with isopropyl
alcohol, and let dry for 3 minutes
or more.
Attaching of spacer
Attach the spacer set the positions
for the glass to be installed.
Gluing of window dam and widshield glass moulding
Glue the window dam and windshield glass moulding to the glass, following
the standard position all the way between the dam and moulding.
Application of primer
Apply to the adhesion surface of
the body and let dyr for 3 minutes
or more.
Application of primer
Apply sufficient primer everly to the adhesion surface so that there is no
patchiness. After application, let dry for 3 to 15 minutes.
Application of adhesive
Within 15 minutes after applying the primer, apply the adhesive evenly all
the way between the dam and moulding.
Installing the glass
After applying the adhesive, lightly press the glass evenly
so that it adheres completely.
Cleaning
After removing any adhesive that is sticking out or adhering to the body or glass with a spatula, etc. clean off with
isopropyl alcohol.
Checking for water leaks
Carry out a shower test to check that no water will leak
through.
ESTC090A
BD -26
BODY (INTERIOR & EXTERIOR)
REMOVAL
1.
2.
4.
ESTC0950
To remove the windshield, first remove the following
parts :
1)
Front pillar trims
2)
Inside rear view mirror
3)
Wiper arms
4)
Cowl top cover
5)
Windshield glass molding
Use the Special Tool (09861-31100) to cut through the
sealant.
09861-31100
ESDA230B
3.
Make mating marks on the glass and body if the glass
is to be reinstalled.
NOTE
Use chalk or equivalent to make mating marks on the
glass and body.
ESDA230C
Take out the windshield glass with Special Tool, Glass
Holder.
09861-31400
ESDA230D
INTERIOR
INSTALLATION
1.
BD -27
4.
ESTC1000
Using a cutter knife or the Special Tool, scrape the
old sealant smoothly to a thickness of about 2 mm
(0.08 in.) on the bonding surface around the entire
windshield flange.
CAUTION
Glue the rubber dam to the inside surface of the windshield glass around the entire edge as shown, to contain the sealant during installation.
PART
"A"
Remarks
UPPER
12.5mm constant
SIDE
12.5mm constant
Be careful not to remove more adhesive than necessary, and also not to damage the paintwork on
the body surface with the knife. If the paintwork is
damaged, repair the damaged area with touch-up
paint.
Glass molding
sub
Sealant
"A"
Glass
15mm
Molding
8mm
09861-31200
ESDA235A
5.
Install the windshield glass molding without any gaps.
ESDA235B
2.
Clean the body bonding surface with a sponge dampened in alcohol or wax and grease remover.
3.
Center a new windshield glass in the opening. Mark
the location by scribing lines across the glass and
body with a grease pencil at the four points as shown.
Molding
Glass
ESDA235D
ESDA235C
BD -28
6.
BODY (INTERIOR & EXTERIOR)
Apply a light coat of glass primer to the outside of the
dam.
10. Scrape or wipe excess adhesive off with a putty knife
or gauze. Fill all cavities around the windshield glass.
NOTE
1.
2.
3.
09861-31400
Never touch the primed surfaces with your hand.
If you do, the adhesive may not bond to the glass
properly, causing a leak after the windshield
glass is installed.
Do not apply body primer to the glass.
Keep water, dust, and abrasive materials away
from the primed surface.
Apply primer
ESDA230D
11. Perform a water-leak test for the windshield. Use a
cold water spray, being careful not to direct a powerful
stream of water on the new adhesive material. Allow
water to spill over the edges of the glass.
12. If there are leaks, dry the affected area, then apply
sealant.
ESDA235E
7.
Apply a light coat of body primer to the original sealant
remaining around the window opening flange. The
glass should be installed 10 minutes after you apply
the primer.
NOTE
• Let the car stand for at least four hours after
windshield installation. If the car has to be used
winthin the first 8 hours, it must be driven slowly.
• Keep the windshield dry for the first hour after
installation.
ESDA235F
8.
Pack adhesive into the cartridge avoiding air pockets,
to ensure continuous application. Put the cartridge
in a caulking gun or Sealant Gun, and run a bead of
adhesive around the edge of the glass.
NOTE
Apply the adhesive within 5 minutes after applying the
glass primer.
9.
Using suction cups or Special Tool, lower the glass
over the opening, align it with the marks made in step
3 and set it down on the sealant.
ESDA235G
13. Install the removed parts.
NOTE
Advise the customer not to do the following things for
two to three days :
• Slam the doors with all the windows rolled up.
• Twist the body excessively (such as when going
in and out of driveways at an angle or driving over
rough, uneven roads).
INTERIOR
BD -29
TAILGATE GLASS
COMPONENTS
ESTE0500
3
3
A
1
A
C
C
B
D
B
D
2
1
4
1
1
4
5
5
5
5
A-A
1.
2.
3.
4.
5.
B-B
C-C
D-D
Tailgate glass
Tailgate glass lower moulding
Fastener
Tailgate glass dam
Sealant
ESTE050A
BD -30
BODY (INTERIOR & EXTERIOR)
REMOVAL
1.
INSTALLATION
ESTC1100
To remove the tailgate glass, first remove the following
parts:
1)
Rear wiper arm
2)
Defogger wire connector
3)
Tailgate trims
1.
ESTC1150
Using a cutter knife or the Special Tool, scrape the old
sealant smoothly to a thickness of about 2 mm (0.08
in.) on the bonding surface around the entire tailgate
glass.
CAUTION
Be careful not to remove more adhesive than necessary, and also not to damage the paintwork on
the body surface with the knife. If the paintwork is
damaged, repair the damaged area with touch-up
paint.
09861-31200
ESTC110A
2.
Remove the tailgate glass the same as the windshield
glass.
ESDA235B
2.
Clean the body bonding surface with a sponge dampened in alcohol or wax and grease remover.
3.
Center a new tailgate glass in the opening. Mark the
location by scribing lines across the glass and body
with a grease pencil at the four points as shown.
ESDA235C
INTERIOR
4.
BD -31
Glue the rubber dam to the inside surface of the tailgate glass around the entire edge as shown, to contain the sealant during installation.
PART
6.
Apply a light coat of glass primer to the outside of the
dam.
NOTE
"A"
Upper
12.5mm constant
Side
12.5mm constant
1.
Glass molding
sub
2.
3.
Never touch the primed surfaces with your hand.
If you do, the adhesive may not bond to the glass
properly, causing a leak after the tailgate glass is
installed.
Do not apply body primer to the glass.
Keep water, dust, and abrasive materials away
from the primed surface.
Apply primer
12.5 mm
"A"
ESTC115B
5.
Install the tailgate glass molding without any gaps.
ESDA235E
7.
Apply a light coat of body primer to the original sealant
remaining around the window opening flange. The
glass should be installed 10 minutes after you apply
the primer.
8.
Pack adhesive into the cartridge avoiding air pockets,
to ensure continuous application. Put the cartridge
in a caulking gun or Sealant Gun, and run a bead of
adhesive around the edge of the glass.
Molding
Glass
ESDA235D
NOTE
Apply the adhesive within 5 minutes after applying the
glass primer.
9.
Use suction cups or Special Tool, lower the glass over
the opening, align it with the marks made in step 3 and
set it down on the sealant.
10. Scrape or wipe excess adhesive off with putty knife or
gauze. Fill all cavities around the tailgate glass.
09861-31400
ESDA230D
BD -32
BODY (INTERIOR & EXTERIOR)
11. Perform a water-leak test for the tailgate glass. Use a
cold water spray, being careful not to direct a powerful
stream of water on the new adhesive material. Allow
water to spill over the edges of the glass.
ESDA235G
12. If there are leaks, dry the affected area, then apply
sealant.
NOTE
• Let the car stand for at least four hours after tailgate glass installation. If the car has to be used
within the first 8 hours, it must be driven slowly.
• Keep the tailgate glass dry for the first hour after
installation.
13. Install the removed parts.
CAUTION
Advise the customer not to do the following things
for two to three days :
• Slam the doors with all the windows rolled up.
• Twist the body excessively (such as when going in and out of driveways at an angle or driving over rough, uneven roads).
BUMPER
BD -33
BUMPER
FRONT BUMPER
COMPONENTS
ESTE0550
Radiator grille
Side grille
Protector molding
Fog lamp
Front bumper cover
Front bumper rail
ESTE055A
BD -34
REMOVAL AND INSTALLATION
1.
BODY (INTERIOR & EXTERIOR)
ESTE0600
Remove the head lamp.
ESTE027A
2.
Remove the bumper cover mounting bolts.
ESTE027B
3.
Remove the bumper rail mounting bolts and disconnect the fog lamp connector, then remove the front
bumper assembly.
Mounting torque :
17-26 Nm (170-260 kgŧcm, 12-19 lbŧft)
ESTE027C
4.
Installation is the reverse of removal.
BUMPER
BD -35
REAR BUMPER
COMPONENTS
ESTE0700
Molding
Rear fog lamp
Rear bumper cover
Rear bumper rail
ESTE070A
BD -36
REMOVAL AND INSTALLATION
1.
BODY (INTERIOR & EXTERIOR)
4.
ESTE0750
Remove the rear combination lamp.
Remove the bumper rail mounting bolts.
Mounting torque :
17-26 Nm (170-260 kgŧcm, 12-19 lbŧft)
ESTE075A
2.
ESTE075D
Remove the rear mud guard.
ESTE075B
3.
Remove the rear bumper cover mounting screws and
clips.
ESTE075C
5.
Remove the rear bumper assembly.
6.
Installation is the reverse of removal.
SEAT
BD -37
SEAT
FRONT SEAT
COMPONENTS
ESTC1400
[DRIVER'S SEAT]
Seat back
Head rest
Seat back
Seat inner track
17-26 (170-260, 12-19)
Seat cushion
Seat outer track
17-26 (170-260, 12-19)
Seat outer cover
TORQUE : Nm (kg·cm, lb·ft)
ESTC140A
BD -38
BODY (INTERIOR & EXTERIOR)
[PASSENGER'S SEAT]
Seat back
Head rest
Seat back
Seat outer cover
Seat outer track
Seat cushion
Seat inner track
17-26 (170-260,12-19)
Seat under tray
17-26 (170-260,12-19)
TORQUE : Nm (kg·cm, lb·ft)
ESTC140B
SEAT
BD -39
REMOVAL AND INSTALLATION
1.
ESTC1450
Pull out the front seat mounting cover and remove the
bolts.
V5BD044A
2.
Remove the front seat assembly.
ESTC145A
3.
Install the front seat assembly after inserting the guide
pin on the body hole.
Tightening torque :
35-55 Nm (350-550 kgŧcm, 25.3-40 lbŧft)
Guide pin
ESDA305B
BD -40
BODY (INTERIOR & EXTERIOR)
REAR SEAT
COMPONENTS
ESTE0800
Rear seat back
Rear seat back striker
17~26 Nm
(170~260 kgf·cm, 12~19 lbf·ft)
Rear seat cushion
ESTE080A
SEAT
BD -41
FRONT SEAT BELT
COMPONENTS
ESTC1600
[FRONT SEAT BELT]
Anchor cover
Dust cover
Front seat belt
Buckle
[REAR SEAT BELT]
Anchor plate
Rear seat belt
ESTC160A
BD -42
REMOVAL AND INSTALLATION
1.
BODY (INTERIOR & EXTERIOR)
5.
ESTC1650
Remove the front seat belt
Remove the door scuff trim.
ESTC165E
ESTC165A
2.
Remove the lower anchor plate.
ESTC165B
3.
Remove the upper anchor plate and center pillar lower
trim.
ESTC165C
4.
Remove the webbing guide.
ESTC165D
6.
Installation is the reverse of removal.
SEAT
BD -43
REAR SEAT BELT
REMOVAL AND INSTALLATION
1.
4.
Remove the rear seat bolt.
ESTC1700
Remove the rear seat.
ESTC170D
5.
ESTC170A
2.
After removing the rear seat upper anchor plate, remove rear pillar trim.
ESTC170B
3.
Remove the rear seat lower anchor plate.
ESTC170C
Installation is the reverse of removal.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement