DATA SHEET
CROSS TECHNOLOGIES, INC.
Rev_B
06/09/14
2099-17 10MHz Source/Inserter
The 2099-17 10 MHz Source / Inserter is a 10 MHz, ±0.01 ppm oven controlled crystal oscillator (OCXO) with circuitry to insert the 10
MHz signal and DC voltage on L-band lines for an LNB and SSPB. Multi-function push button switches select internal or external 10
MHz and insertion of 10 MHz on the L-band lines. LEDs indicate alarm (red), remote operation (yellow), DC power (green), OCXO
oven warm-up (yellow), and presence of external 10MHz reference (red). Remote control allows remote configuration of front panel
commands and monitoring LNB and SSPB current. Parameter selection and LNB and SSPB current appear on the LCD display.
Connectors are BNC female for RF and 10 MHz external input and output signals. LNB or SSPB +24 VDC can be inserted on the RF
lines by installing the fuses. AC power is 100-240 ±10% VAC, 47-63 Hz. The 2099-17 is housed in a 1 RU chassis, 16” deep.
MODEL 2099
RX 0.32 A
TX 1.86 A
SOURCE/INSERTER
REF ON
REF OFF
MENU
CROSS TECHNOLOGIES INC.
EXECUTE
ALARM
REMOTE POWER
OVEN
EXT REF
Front Panel
EQUIPMENT SPECIFICATIONS*
---------RX and TX L-band Insertion--------RF Input/Output Characteristics
Frequency
950 - 2150 MHz
Impedance
50Ω
Return Loss
>12 dB, 0.95-1.5 GHz
>10 dB, 1.5-2.15 GHz
Insertion Loss
< 1 dB, 0.95-1.5 GHz
< 2 dB, 1.5-2.15 GHz
Frequency Response
±1.0 dB, 950 - 2150 MHz;
± 0.5 dB, 36 MHz BW
LNB, SSPB DC Power Characteristics
Voltage/Current
LNB +24 VDC, 0.5 A, max.
SSPB +24 VDC, 2.5 A, max.
Call for other voltages
Load Regulation
±5 %
---------10 MHz Reference--------Output Characteristics (on L-band RF)
Level
+2 dBm ± 2 dB
Harmonics
<-30 dBC, <-40 dBC typ
Level to non-insert end
<-20 dBm, <-30 dBm typ
Input/Output Characteristics (on BNC connectors)
Impedance, Return Loss 50Ω/75Ω, 18 dB
Level
+3 dBm ± 3 dB
Harmonics (Output)
< -30 dBC, < -40 dBC typ.
Oscillator
Stability
± 0.01 ppm max over temp
Aging, per day
± 0.001 ppm
Aging, per year
± 0.1 ppm
Warm up, 4 minutes
± 0.1 ppm
Warm up, 1 hour
± 0.01 ppm
Tuning Adjust
± 0.5 ppm
Phase Noise @ Freq
dBC/Hz
10Hz
-110
100Hz
-140
1kHz
-149
10 kHz
-149
---------Chassis / Other-------Controls, Indicators
INT/EXT 10 MHz Select Direct readout LCD; manual or remote selection
10 MHz Insert Select
Direct readout LCD; manual or remote selection
LNB, SSPB Current
Direct readout, remote monitor
Power, Alarm, Remote
Green LED; Red LED; Yellow LED;
Oven Warm-up, Ext Ref Yellow LED; Red LED
Remote
RS232C, 9600 baud (RS485, option Q)
Other
RF Connectors
BNC, 50Ω (female)
10 MHz Connectors
BNC, 75 / 50 (female)
Alarm/Remote Connector DB9 (female) - NO or NC closure on Alarm
Size
19 inch, 1RU chassis 1.75”H X 16.0”D
Power
100-240 ± 10% VAC, 47-63 Hz, 90 watts max
Available Options
Q - RS485/RS422 Remote Interface
Connectors/Impedance
B – 75Ω BNC (RF)
F – 75Ω Type F (RF)
L-BAND
TX
IN
L-BAND
TX
OUT
SSPB
+24VDC
INT 10MHz
OCXO
RX 0.32A
REF ON
TX 1.86A
REF OFF
CONTROLLER
LNB
+24VDC
fuse
L-BAND
RX
OUT
L-BAND
RX
IN
Block Diagram
*10˚C to 40˚C; Specifications subject to change without notice.
Cross Technologies, Inc.
•
6170 Shiloh Road • Alpharetta, GA 30005
EXT 10MHz
AUTO
fuse
www.crosstechnologies.com
• 770.886.8005 • FAX 770.886.7964
Download PDF