Quick Installation Guide 1/3” Network Camera, WDR, Day&Night, 3-9mm,

EN
Quick Installation Guide
1/3”
Network
Camera,
WDR, Day&Night, 3-9mm,
1920x1080, 3x AF Zoom, Infrared, PoE
PXB-2080Z03 D
NETWORK AF-ZOOM CAMERA
Safety Precaution
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
CAUTION: TO REDUCE THE RISK OF ELECTIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.
03
NETWORK AF ZOOM CAMERA
Safety Precaution
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the
cable is not subjected to heavy loads, kinks or damage and no moisture can get
in.
Never open the device such as boards or lens.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.
04
NETWORK AF ZOOM CAMERA
Contents
p.03~04
Safety Precaution
p.05
Contents
p.06~07
Features
p.07
Composition
p.08
Dimensions
p.08
Part Names
p.09~11
Installation Instructions
p.12~28
Operating Instructions
p.29~30
Specifications
05
NETWORK AF ZOOM CAMERA
Features
Key Features
• Full HD, 2Mega Pixel, NETWORK CAMERA, 1920x1080(30p/25p)
• ONVIF & PSIA Conformance
• Built-in f=3~9mm, F1.2~F2.1 Day&Night zoom lens
(Optical 3x Auto focus zoom / Digital 32x zoom)
• Real time True WDR (Wide Dynamic Range) / 30fps
• Improved noise figure with the enhanced 3DNR
• Dual Filter Switcher
• Color D/N, optimized color mode for night
• Focusing Status Indicator on Screen
- ★(Blue) Focusing in process
- ★(White) Focusing Completed
• Various Zooming Technologies
- Smart Motion Zoom (Automatic zoom in/out when motion is detected)
- Pointing Zoom (which enables the programmable zooming at any area)
- Preset Zoom
• Home Position setting
• Motion Detection, Privacy Mask, Defog, Sens-up, BLC/HLC, H/V/HV Flip,
Smart IR, Title Set, Motion Deblur
• ID / TITLE / ZOOM RATIO DISPLAY
• Enhanced Sensitivity by DSS technology
• H.264 / MJPEG dual streaming
• Full duplex 2 way Audio, Alarm IN/OUT
• Max 30fps live view @ 1920x1080p
• Audio & Alarm input/output
• Slot for Standard SD memory card verified up to 32GB
• Zoom & Menu Control via either Local Joystick or WEB
• OSD menu & CVBS Video output BNC for easy installation & maintenance
• Circuit protection against faulty connection in power polarity
• Isolated power supply against ground loop problem
• PoE(IEEE Std. 802.3af) & Local dual power
• Built-in 4 High power LEDs
• LED ON/OFF Control
• Dual Window, One touch 3-Axis locking bracket, Easy Installation Pad
• Built-in Cooling Fan & Heating function
• IP67 Protection
06
NETWORK AF ZOOM CAMERA
Features
General Description
This camera realizes the natural and crisp image as you see the scene in front
of you by adopting Auto Focus Full HD(1920x1080p) camera module.
Highly detailed pictures can be achieved and color reproducibility deserves
attention.
• With ICR mechanism,
- Enhances its sensitivity about 10x at night time
- Can accepts the infrared light
• With 24VAC/12VDC dual power & PoE (Power Over Ethernet) design,
- Offers the flexibility of installation
- Ensures the reliability
Composition
Plastic Anchor:
6 x 30mm (4pcs)
Mounting Screw:
4 x 30mm (4pcs)
Camera
Operating
Instruction
Assembly Screw:
4 x 14mm (4pcs)
Easy
Bracket
Video Sub-out:
Cable (1pc)
Mounting Template
Wiring Connector
(1pc)
Coupler for
RJ45 Cable (1pc)
Cable Signal
Sticker
07
Torque Wrench:
3mm (1pc)
EMI Ferrite
Core (1pc)
NETWORK AF ZOOM CAMERA
Dimensions
(unit : mm)
80
267
100
86.40
75.90
190
87.30
108
Part Names
SUNSHIELD BOLT
ETHERNET &
POWER CABLE
SUNSHIELD
OSD Setup
CONTROL COVER
DUAL WINDOW
BRACKET
FRONT CASE
REAR CASE
LOCK/UNLOCK
SCREW
08
EASY
BRACKET
NETWORK AF ZOOM CAMERA
Installation Instructions
1. Locate the mounting template at the installation position and drill the ceiling or
wall if needed. ( *The easy bracket can not be installed on the ceiling)
2. Place the easy bracket on pre-drilled position and fix it through using mounting
screws(4x30mm). Skip this step when an easy bracket is not installed.
3. Route the power cable to the connecting place.
Hook up the camera bracket with the easy bracket as illustrated below.
4. Fix the camera bracket through using assembly screws (4x14mm).
5. Set the camera’s viewing angle.
6. Put the sunshield to the camera unit and tighten the sunshield-bolts.
Assembly Screw
: 4x14mm
Torque Wrench
Mounting Screw
: 4x30mm
1
2
4
3
REAR VIEW
Cable exit
CAUTION
• Extreme care should be taken NOT to scratch the window in front of lens.
• Care should be taken the cable is NOT to be damaged, kinked or exposed
in the hazardous area.
• Do not expose the camera directly to a strong light source such as the sun
or spot light.
09
NETWORK AF ZOOM CAMERA
Installation Instructions
Pan & Tilt adjustments
• Unlock the screw on the camera bracket through using the torque wrench supplied
• Set the camera’s viewing angle then lock the screw on the bracket.
1) Pan limit:
Pan is limited to +/- 90°.
2) Tilt limit:
Tilt is limited to 0°(2°) min ~ 90° max.
for wall(ceiling) installation respectively
with reference to the wall(ceiling) when
the inclination of camera module is 0°,
that is, the image is aligned horizontally.
90°
90°
88°
90°
• on the ceiling
• on the wall
3) Inclination limit
(Horizontal image alignment):
Inclination limited to +/-90° max.
±90°
Torque
wrench
Lock/Unlock
Screw
■ Adjustment of viewing angle with a bracket
10
NETWORK AF ZOOM CAMERA
Installation Instructions
Installation and commissioning Instructions
• Make sure the power is removed before the installation.
• After all connections are finished properly, follow the order for applying power.
a) Plug the network cable into RJ-45 Ethernet Port.
If PoE is the unique power, there will be no need to connect Power terminal.
b) When DC12V or AC24V Local power is necessary, first connect the low
voltage (DC12V or AC24V), then plug the AC adapter to AC outlets to avoid
an improper reset from power jitter and a damage from the surge voltage
when no load.
► When PoE and Local dual power are connected at the same time,
Local power has priority.
Power Supply Connections
Camera can work with either 24VAC or 12VDC, dual voltage power and PoE
(IEEE Std. 802.3af). Primary and secondary grounds are completely isolated
to avoid the possible ground-loop problems.
~24V/DC12V (RED)
~24V/GND (BLACK)
ALARM-IN (GREEN)
ALARM-OUT (BLUE)
GND (GRAY)
AUDIO-IN (BROWN)
GND (GRAY)
AUDIO-OUT (ORANGE)
EMI Ferrite Core Connection
50mm
50mm
11
NETWORK AF ZOOM CAMERA
Operating Instructions
Using OSD controller
Setup menu can be accessed and controlled by OSD control joy stick on the
side of camera unit.
Five commands are available with the joy stick.
The design of OSD could be different according to the Model.
Standard
SD Card Slot
IP RESET
Cover Open
OSD Control
Joy Stick
Video Sub-out Connector
Description of the joystick operation
1) SET Key (●) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down for about 1.5sec
2) UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move
the cursor up or down.
3) LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu.
Used to adjust the desired menu selection and to move the cursor left
or right.
4) ‘☟’denotes the long press down straightly for about 2 seconds
Description of the ZOOM&FOCUS* adjustment
(*) Works only when OSD Menu is inactive and IP is not connected.
1) ▲ : Zoom In
2) ▼ : Zoom Out
3) ◄ : Focus Near
4) ► : Focus Far
12
NETWORK AF ZOOM CAMERA
Operating Instructions
Quick Network Setup
NOTICE
After camera is connected with IP, its control is available via WEB Viewer.
To access the ADMIN on IP INSTALLER
ID: root
PW: root
The network camera‘s default IP address is: 192.168.1.10.
Therefore, to access the camera for the first time, set the PC‘s address as shown.
192.168.1.XX; for example:
IP Address: 192.168.1.20
Subnet Mask: 255.255.255.0
• Enter the camera’s IP address in the URL bar of the Web browser window and
hit “Enter.”
• Enter the default user name (root) and password (root) in the prompt request
dialogue. It is also possible to reset IP parameters to the original factory default
settings by pressing the IP reset.
• If the Information message doesn‘t come out due to the problems like network
failure, you can start the manual installation.
• Click the Install ActiveX Control, and the pop-up window will be displayed.
After the installation is successfully completed, Smart Viewer window will be
displayed.
13
NETWORK AF ZOOM CAMERA
Operating Instructions
1. Assigning an IP address
To assign an IP address to the camera proceeded as follows:
Click Network Configuration on the Network Configuration menu.
• Depending on the service type, the network configuration can be in any of Static
IP, DHCP Client, or PPPoE. You need to set up the network camera according to
your network type.
• For static IP, select static IP and input values for IP address, NetMask, Gateway,
DNS1, DNS2 and click apply for saving settings. After apply, program will ask
closing web browser for updates, which will take 20~30 seconds.
14
NETWORK AF ZOOM CAMERA
Operating Instructions
• For DHCP, DHCP server must exist in the same network environment. Select
DHCP Client from Network Configuration, click Apply.
• PPPoE is used to connect IP products to PPPoE modem provided by ISP.
Since PPPoE needs verification, ID and password are necessary to access
network. Type in ID and password.
2. Administrator password
To change the password for the administrator, click Admin Password on System
Configuration menu.
• Default ID for admin account is fixed as “root” and not allowed to change.
In Old Password field, enter the current password. In both New Password and
Confirm Password fields, enter the same new password.
• The password must be between 4 and 23 alphanumeric letters. Click Apply to
put it into effect. Because you have replaced the password with a new one, the
existing network connection made with old password now is lost.
• You will have to reconnect for using the new password.
15
NETWORK AF ZOOM CAMERA
Operating Instructions
3. Accessing the camera setup menu
Camera SETUP menu can be accessed in two ways via web viewer.
Most frequent controls are available with the parameters directly in the below
table. More complicated settings such as PRIVACY, POINTING ZOOM & SMART
MOTION settings are available via ‘ADVANCED CAMERA MENU’ by activating
the camera OSD menu.
※Lens Initializing is strongly recommended at the first stage of setup menu control.
MENU V5.xx
PRIVACY
MOTION
TITLE SET
SMART IR
POINTING ZOOM
PRESET ZOOM
HOME POSITION
BLC/HLC
MOTION DEBLUR
EXIT
10
EXT
16
OFF
OFF
OFF
ON
ON
ON
SAVE&EXIT
NETWORK AF ZOOM CAMERA
Operating Instructions
Direct Control on Web-menu
SPECIAL
DEFAULT
DESCRIPTION
AUTO
FOCUS
ZOOM
PUSH
ZOOM PUSH, AUTO and MANUAL modes are available for
zoom & focus.
MANUAL – Zoom in/out can only be adjusted by ▲,▼ of OSD
control joystick or Focus Near/Far button on WEB.
AUTO – Focusing is always working.
ZOOM PUSH – Focusing is activated only when zoom in/out is
working. It can be focused any area on video using by Near/Far
button on web. It works to make the target focus on video when
the focusing is not clear.
Max.
D-ZOOM
OFF
D-ZOOM(Digital zoom) is available up to 32x.
D-ZOOM starts working when the optical zoom reaches its
maximum tele-position. Zoom ratio is displayed on the right bottom
corner of the monitor if DISPLAY ZOOM RATIO is set to ON.
EXPOSURE
MODE
AUTO
Can set EXPOSURE MODE to AUTO, IRIS Priority, SHUT.
Priority, MANUAL and Flickerless
AUTO – Optimizes the video level by controlling the iris and the
shutter speed automatically.
SHUTTER. Priority - Selects to fix SHUTTER speed in a certain
speed and the video level is controlled by an automatic iris control.
This mode is useful when the color rolling occurs under the fluorescent lighting. It is not recommendable at outdoor in the daytime.
IRIS Priority – Selects to fix IRIS in a certain aperture and the
video level is controlled by an automatic shutter control. IRIS
Level menu is activated when EXPOSURE MODE is set to IRIS
Priority. Lower IRIS LEVEL will close more Iris and increase the
field of depth in the daytime but significantly decrease the low
light performance. Too much low IRIS LEVEL will result in the
foggy video by the diffusion from the lens iris.
MANUAL – Iris and Shutter can be set to fix.
Flickerless – Reduces the flicker in video when US(60Hz) / EU
(50Hz) mode is used in 50Hz/60Hz fluorescent lighting respectively.
SHUT. Priority, MANUAL and Flickerless modes disable
SENS-UP and MOTION BLUR functions.
BRIGHTNESS
Day:10
Night: 8
COLOR GAIN
Adjusts the color level of video. (0~15) It can only be adjusted to
Day:10
Night: 10 be set to COLOR D/N mode in Day & Night function.
GAMMA
0.55
Adjusts the brightness of video. (0~20)
Adjusts the gamma of video. (0.45 ~0.75)
17
NETWORK AF ZOOM CAMERA
Operating Instructions
AGC amplifies the video gain for brighter video but noise and
white pixel accordingly.
AGC level less than 10 disables AUTO in DAY/NIGHT
AGC
10
SENS-UP
AUTO
WDR
OFF
Improves the visibility for the high bright area and the dark area
by the double captures of image with LONG and SHORT exposures.
※CVBS video signal - Connecting 2nd video to CVBS port
disables WDR function temporary. It should be considered when
installer adjusts the video with installation monitor via CVBS
video signal
WDR
Weight
MID
WDR level can be selected from LOW, MID and HIGH.
Care should be taken to select this mode because video may
lose its quality in some environments by the over compensation.
BLC
(Back Light
Compensation)
OFF
ON – Improves the visibility for the dark object by the bright back
light. Outside area of BLC window be can over saturated.
Available to set BLC POSITION at ADVANCED CAMERA MENU>
BLC/HLC>BLC POSITION
HLC – Cuts out the highlight area with black mask and excludes
it from compensation. Lower HLC LEVEL cut out video from the
lower level. HLC LEVEL is adjustable at ADVANCED CAMERA
MENU>BLC/HLC>HLC LEVEL
3D-NR
MID
3D-NR is a very sophisticated and powerful time-based noise
reduction technology by monitoring the noise for the several video
frames and defining and eliminating them consecutively at low light.
Higher setting reduces noise much more but results in losing
the sharpness and the tail effect or the motion blur for the fast
moving target at low light.
DAY&NIGHT
EXT
for
IR LED
type
COLOR – Forcibly DAY/NIGHT is disabled and outputs color video.
AUTO – Used when DAY or NIGHT is determined by light level
through the lens and DAY from/to NIGHT is switched automatically
by the scene brightness.
When EXPOSURE>AGC is less than 12, DAY/NIGHT AUTO is
disabled and forcibly switches to _(DAY) to avoid the malfunction.
EXT, B/W(NIGHT) and COLOR(DAY) is independent on AGC
The brighter video can be obtained by increasing the exposure
time in the night with SENS-UP. SENS-UP is the maximum
integrations of frame by DSS(Digital Slow Shutter) in the low light.
AUTO – SENS-UP is enabled or disabled automatically by the
scene brightness.
OFF – Disables SENS-UP
18
NETWORK AF ZOOM CAMERA
Operating Instructions
DAY&NIGHT
level. When EXTERNAL IR LED is used with NON IR LED model,
please set to IR LED MODE ON.
B/W – Forcibly removes IR cut filter and switches to B/W
regardless of light level.
EXT – DAY or NIGHT is determined by the built-in light photo
DAY
sensor. Camera with IR LED must be set to EXT.
for
Non TDN COLOR D/N – Forcibly Color mode, optimized for night condition.
It is available to recognize colors of car, people and moving objects
type
even at night. Parameters can be controllable & programmable
according to circumstance. Application for bright circumstance at
night such as downtown, civic area, street, mall and etc.
AUTO
for
Non IR
type
Conventional COLOR mode in NIGHT
COLOR D/N mode in NIGHT
Day & Night
Threshold
10
D↔N Threshold is a threshold level and Gap to switch from
DAY to NIGHT. (0~20)
Low makes camera entered NIGHT at lower light level.
High makes camera exited NIGHT at brighter light level.
Day & Night
GAP
MID
Sets the gap level switching from/to DAY(color) or NIGHT(B/W).
WHITE
BALANCE
MODE
ATW
ATW, ONE PUSH and MANUAL are available for the white balance
modes.
ATW – White balance is continuously working along with the
color temperature changes in the range of 2,000K~8,500K.
ONE PUSH – White balance works only when ONE PUSH is
selected.
MANUAL – This mode can be used only when the color
temperature does not vary. White balance is fixed to the settings
by R_GAIN and B-GAIN
ATW-ext – White balance is continuously working along with the
color temperature changes in the range of 1,800K~11,000K.
WB Manual
R-Gain/
B-Gain
10
Activates when WHITE BALANCE is set to MANUAL.
Adjustable 0~20.
SHARPNESS
10
Adjusts the sharpness of video.
19
NETWORK AF ZOOM CAMERA
Operating Instructions
MIRROR /
FLIP
No Mirror, Reverses the video left and right and/or up and down by
No Flip MIRROR/FLIP.
No Mirror, No Flip : Normal display without mirroring or flipping
No Mirror, Flip : Video is reversed upside down.
Mirror, No Flip : Video is reversed left and right.
Mirror, Flip : Video is reversed left and right and upside down.
When the video is reversed by Ver. or HV, then the joystick
directions are reversed accordingly. This feature is very useful
when a camera is installed in upside down.
DEFOG
OFF
AUTO – Enhances the foggy video automatically according to
status of scene.
MANUAL –Sets to enhance the foggy video manually regardless
of status of scene
DEFOG
Weight
MID
LEVEL – LOW, MID, HIGH
Video quality can be less in normal environments.
OFF
ON enables to display the Zoom Ratio on the bottom right
corner. OZx.x appears during the optical zoom and DZx.x will
display by multiplying the optical zoom ratio and the actual digital
zoom ratio.
DISPLAY
Zoom Ratio
DISPLAY FOCUS
INDICATOR
ON
ON enables to display the Focus Indicator on Monitor
DISPLAY ID
OFF
ON enables to display Camera ID on Monitor.
DISPLAY Tittle
OFF
ON enables to display Camera Tittle on Monitor.
IR LED
Control
AUTO
LENS
INITIALIZE
IR LED Control(AUTO/OFF) is available with IR LED model only.
If IR LED is set to OFF, IR LED will be turned OFF but DAY or
NIGHT is still determined by the built-in light photo sensor.
Lens initialization is necessary during the installation or the
regular operation to align the position data with the mechanical
positions whose lens elements may move and deviate from its
calibrated position by the shock or vibration, for example, during
the transportation.
LENS INIT checks the positions for zoom and focus at both of
the end positions and saves them for the references.
Lens initialization is automatically executed at power up.
[ CAUTION ]
It is strongly necessary to execute LENS INIT in cases below;
1) At the final step for the installation.
2) When focus becomes out of control by the shock or vibration.
20
NETWORK AF ZOOM CAMERA
Operating Instructions
Advanced Camera OSD menu
Click ‘ADVANCED CAMERA MENU’ bar at CAMERA CONTROL menu to activate
the camera OSD menu.
Click Up/Down/Left/Right bars to navigate or change the parameters.
These options have been pre-configured at the factory for optimal performance.
MENU
V5.xx
PRIVACY
MOTION
TITLE SET
SMART IR
POINTING ZOOM
PRESET ZOOM
HOME POSITION
BLC/HLC
MOTION DEBLUR
EXIT
OFF
OFF
↵
|::::::::::::::::::| 0
OFF
OFF
OFF ↵
↵
ON
SAVE&EXIT ↵
1. PRIVACY (default: OFF)
10 Privacy zones which can be enabled individually by ZONE DISP are available
to mask the video.
• ZONE NUMBER – Sets a number to select a privacy zone from 1~10.
• ZONE DISP – ON enables a relevant privacy zone.
• H-POS, V-POS, H-SIZE and V-SIZE – Adjust the size and position of zone.
• COLOR – Selects the color for masking zone from eight colors.
• TRANSPARENCY – Defines the transparency for the mask zone.
2. MOTION (default: OFF)
MOTION can detect the changes in the motion window and displays the results
in blocks and/or a text message.
• SENSITIVITY – Adjusts the detection sensitivity for motion. High value increases
the sensitivity to detect the small motion easily. Too high sensitivity will cause the
erratic detection by the tree leaves or the light level changes and too low setting
will fail in detecting the motion.
• H-POS,V-POS, H-SIZE,V-SIZE - Adjust the size and position of the detection
window.
• BLOCK DISP – ON enables to display the blocks for the detected area.
• MOTION OSD – ON enables to display a text message, MOVING !!!
21
NETWORK AF ZOOM CAMERA
Operating Instructions
• SMART MOTION ZOOM– ON enables to Automatic Zoom IN/OUT when motion
is detected and also enables MOTION OSD to ON.
Area to be zoomed in by SMART MOTION ZOOM can be set at MOTION >
SMART MOTION ZOOM. Clicking Up/ Down/ Left/ Right or Enter bars for ZOOM
TARGET varies the viewing angle to be zoomed when the motion occurs.
Set the video left and right and/or up and down by MIRROR/FLIP.
(See page 25 “SMART MOTION ZOOM” for detail)
• STAY ZOOMING – Sets the duration time for zooming by Motion.
NOTICE
: SMART MOTION ZOOM does not work at low sensitivity and B/W mode.
CAUTION
Set the direction of video by MIRROR/FLIP before SMART MOTION ZOOM setting.
Otherwise the zoom target could be different from your intention.
3. TITLE SET
Camera title(name) can be set and editable up to 15 alpha numeric and symbolic
characters from ASCII codes(ENGLISH only).
Clicking the Up/ Down/ Left/ Right bars to move the cursor for choosing characters
and click the Enter bar to select them. The selected characters are added and
displayed on the top left corner and the cursor moves right automatically for next
input.
• SP - Space is inserted when clicked
• BS - Cursor moves back when clicked
• CLR - Clears all the characters on input line when clicked it
• POS - Sets the title position by using four direction bars and enter bar.
4. SMART IR (default: 0)
SMART IR can be set to reduce the saturation by the strong IR illumination in the
night in any menu of EXT, AUTO and B/W(NIGHT). Setting SMART IR in any menu
is identically applied to other menu. Zero(0) turns off SMART IR and High setting
avoids the saturation strongly but the corners will be darker accordingly.
5. POINTING ZOOM (default: OFF)
ON enables to set off-centered location to be the center of zoom.
• H-POINTER, V-POINTER- Able to set the location of zoom center D-Zoom is
available ~32x. (See page 26 “POINTING ZOOM” for detail)
22
NETWORK AF ZOOM CAMERA
Operating Instructions
CAUTION
Set the direction of video by MIRROR/FLIP before POINTING ZOOM setting.
Otherwise location of zoom center could be different from your intention.
6. PRESET ZOOM (default: OFF)
Able to zoom in for the preset area from NVR, VMS or Web viewer.
PRESET ZOOM
ZONE NUM
ZONE VIEW
H-POS
V-POS
O-ZOOM RATIO
D-ZOOM RATIO
STAYING ZOOMING
RETURN
1
ON ↵
5
5
OZ X2.0
DZ X2.0
3sec
RET ↵
By Remote Controlloer only.
[ Web-viewer]
• ZONE NUM : Set a number to select a preset zoom from 1~ 4.
• ZONE VIEW : ON enables a relevant preset zone.
• H-POS and V-POS : Adjust the size and position of preset zone.
• O-ZOOM RATIO: Set the Optical Zoom Ratio from OX 1.1~OX3.0
• D-ZOOM RATIO: Set the Digital Zoom Ratio from DX 1.1~DX5.0
• STAYING ZOOMING : Sets the duration time for preset zoom area.
(See page 28 “Setting Tip for Zoom functions” for more information)
7. HOME POSITION (default: OFF)
: Camera can be configured to return to pre-defined Zoom position automatically
after certain period since ZOOM IN/OUT control is accomplished.
Home Position is recovered even after camera is re-initializing or Power ON/OFF.
• O-ZOOM RATIO: Sets the Optical ZOOM positon as Home Position. (x1.0~x3.0)
• DURATION: When ZOOM IN/OUT control is accomplished, camera returns to
pre-defined Zoom position after Duration time.
If SMART MOTION / PRESET ZOOM are running, duration for Home position
starts after finishing SMART MOTION / PRESET ZOOM.
23
NETWORK AF ZOOM CAMERA
Operating Instructions
HOME POSITION
O-ZOOM RATIO
DURATION
RETURN
OZ X1.5
5sec
RET
8. BLC/HLC
• BLC POSITION (default: SET)
Improves the visibility for the dark object by the bright back light.
Outside area of BLC window can over saturate.
BLC has a target window for compensation and its size and position can be
set by H-POS, V-POS, H-SIZE and V-SIZE.
• HLC LEVEL (default: 10)
Cuts out the highlight area with black mask and excludes it from compensation.
Lower HLC LEVEL cut out video from the lower level.
9. MOTION DEBLUR (default: ON)
ON enables MOTION DEBLUR to reduce the motion blur in a certain indoor
enviroment. Noise or color rolling can increase.
10. EXIT
SAVE & EXIT – Exits the menu mode after saving the parameters.
EXIT – Exits the menu mode without saving the parameters.
24
NETWORK AF ZOOM CAMERA
Operating Instructions
Detail Function Description
▐ SMART MOTION ZOOM
SMART MOTION ZOOM enlarges the certain area defined by a yellow window
to the full sized image when the motion is detected in the black window.
SMART MOTION ZOOM window can be re-sized by adjusting D-ZOOM RATIO
and moved by H-POS and V-POS
SMART MOTION ZOOM
ZONE VIEW
H-POS
10
V-POS
10
O-ZOOM RATIO
OZ X2.0
D-ZOOM RATIO
DZ X2.0
MOTION CHK CUNT
3
RETURN
RET
UNLIKE the conventional zoom which can zoom in/out the center area of image
only, by the flexible zoom location and area, SMART MOTION ZOOM differentiates
its usefulness from others.
That is, a conventional camera installed on the corner of ceiling can zoom the
center of the floor in a room and result in losing the image of door on the side
wall. However, SMART MOTION ZOOM can be set to see the door side and
zoom in that area without missing the IMPORTANT security point.
• H-POS (10) - Moves MOTION ZOOM area(Yellow window) horizontally
• V-POS (10) - Moves MOTION ZOOM area(Yellow window) vertically
• O-ZOOM RATIO (OZ X2.0) - Sets the area size to be Optical zoomed when the
motion occurs in the black window
• D-ZOOM RATIO (DZ X2.0) - Sets the area size to be Digital zoomed when the
motion occurs in the black window.
• H-POS (10) - Moves MOTION ZOOM area(Yellow window) horizontally
• V-POS (10) - Moves MOTION ZOOM area(Yellow window) vertically
• O-ZOOM RATIO (OZ X2.0) - Sets the area size to be Optical zoomed when the
motion occurs in the black window.
25
NETWORK AF ZOOM CAMERA
Operating Instructions
• D-ZOOM RATIO (DZ X2.0) - Sets the area size to be Digital zoomed when the
motion occurs in the black window
• MOTION CHK COUNT (3) - SMART MOTION ZOOM is activated after the
motions in MOTION CHK COUNT are detected in a certain period.
For example, ‘1’ immediately initiates SMART MOTION ZOOM by the motion
detected once. High count number enables SMART MOTION ZOOM with
sureness but with delay and less sensitivity.
▐ POINTING ZOOM
This camera has a very useful and powerful feature, POINTING ZOOM, which
can zoom in/out any area.
UNLIKE the conventional zoom which can zoom in/out the center area of image
only, by the flexible zoom location and area, POINTING ZOOM differentiates its
usefulness from others. That is, a conventional camera installed on the corner
of ceiling can zoom the center of the floor in a room and result in losing the image
of door on the side wall.
However, POINTING ZOOM can be set to see the door side and zoom in that
area without missing the IMPORTANT security point.
POINTING ZOOM can be activated by the joystick operations of ▲ for zoom in
and ▼ for zoom out or via web viewer.
If Zoom ratio becomes out of optical zoom ratio, it automatically turns to Digital
Zoom.
Set D-Zoom Pointer
H-POINTER
10
V-POINTER
10
RETURN
RET
• H-POINTER (10):
Sets the horizontal location of area to be zoomed by POINTING ZOOM.
• V-POINTER (10):
Sets the vertical location of area to be zoomed by POINTING ZOOM.
26
NETWORK AF ZOOM CAMERA
Operating Instructions
* EXAMPLE OF SMART MOTION & POINTING ZOOM
[ At the ATM nearby ENTERANCE ]
[ At the LOBBY ]
27
NETWORK AF ZOOM CAMERA
Operating Instructions
TIP
Setting for Zoom Function with NVR or VMS
● Enter the MENU :
Press buttons 9+5+PSET (PRESET)
● Set the Preset Zoom :
Press buttons 1(or ~4)+PSET (PRESET)
1
● Move the cursor in the MENU :
Moves UP/DOWN/LEFT/RIGHT Joy stick
● Zoom IN: Press button TELE or Spin
the joystick to clockwise.
● Zoom OUT: Press button WIDE or Spin
the joystick to counter-clockwise.
● Select or Choose value in the MENU :
Press button OPEN (IRIS OPEN)
● Exit the Preset Zoom mode :
Press buttons 3+4+PSET (PRESET)
28
3
4
NETWORK AF ZOOM CAMERA
Specifications
ITEM
PXB-2080Z03 D
Imaging Sensor Panasonic 1/3" Progressive Scan CMOS Sensor
Effective Pixels 1,944(H) x 1,092(V)
Min.Illumination 0.0008 Lux (@AGC MAX, DSS x2)
Video Resolution 1920x1080 (30p/25p)
TV System 50Hz(switchable to 60Hz)
Sync. System Internal
Format 16:9 Video format for most popular commercial HDTV monitors
Video Output Ethernet thru RJ45 male & CVBS thru BNC
Video Sub-out NTSC/PAL standard, 1Vpp @75Ω terminated
S/N Ratio More than 50dB (AGC OFF)
Lens Type f=3~9mm F1.2~F2.1 Day&Night Zoom lens (Optical 3x, Digital 32x)
Day & Night True D/N by ICR, Color, Auto, B/W, EXT, Color D/N
LEDs Built-in 4pcs x 855nm High power IR-LEDs
Auto Focus Auto / Zoom Push / Manual
Exposure Control Auto / Iris-Priority / Shutter-Priority / Manual / Flickerless
Min. Focus Distance 0.5m~
Flip OFF/ H/ V/ HV FLIP
White Balance ATW / One Push / Manual / ATWext
WDR True WDR by dual scan images in two frames at 30fps.
Special Features
Functions
SMART MOTION ZOOM, POINTING ZOOM, PRESET ZOOM,
HOME POSITION
NORMAL, WDR, D-WDR, 3DNR, BLC/HLC, Smart IR, D-Zoom,
Motion Detection, Privacy Mask, Defog, Sens-up, Title Set,
Motion Deblur, DSS, LED ON/OFF control
Language English, German, French, Japanese, Korean
Installation Temp. -20ºC ~ +50 ºC (Humidity : 30%RH ~ 80%RH)
Operating Temp. -30ºC ~ +50 ºC (Humidity : 30%RH ~ 80%RH)
External Dimension 108mm(W) x 100mm(H) x 267mm(L)_with Bracket / About 1.35kg
Mechanical Feature IP67, Aluminum Cast, Cooling Fan & Heating function, Dual window,
One touch 3-Axis locking bracket, Easy Installation Pad
29
NETWORK AF ZOOM CAMERA
Specifications
Power Source PoE(IEEE Std. 802.3af ), AC24V~15VA/DC12V=1A, 12W
Circuit protection against faulty connection in power polarity.
Isolated power supply against ground loop problem.
NETWORK SPECIFICATION
Video Encoding H.264 / MJPEG dual streaming
Protocol HTTP, TCP/UDP/IP, ARP, ICMP, RTP/RTSP, multicast, Telnet, IPv6,
PPPoE, SMTP(e-mail), DHCP, NTP, uPNP, ftp, IGMP, ONVIF, PSIA
Transmission Control VBR, CBR ( 32K ~ 12M bps )
CMS Bundled with Full featured 16 channels PC NVR.
32/64 channels available(Option)
IP Installation & Configuration: installation wizard, HTTP, telnet and console,
maintenance Upgrade firmware: HTTP, telnet+ftp
Connectivity Max. 16 simultaneous user connection
SD memory card Slot for Standard SD memory card verified up to 32GB
Audio & Alarm 2way Audio & Alarm in/out
PoE IEEE Std. 802.3af
(*) Design and specifications are subject to change for product improvements without prior notice.
30
eneo® is a registered trademark of
VIDEOR E. Hartig GmbH
Exclusive distribution through specialised
trade channels only.
VIDEOR E. Hartig GmbH
Carl-Zeiss-Straße 8
63322 Rödermark/Germany
Tel. +49 (0) 6074 / 888-0
Fax +49 (0) 6074 / 888-100
www.videor.com
www.eneo-security.com
Technical changes reserved
© Copyright by VIDEOR E. Hartig GmbH
Version 04/2015
Download PDF