Chapter 18 Specifications
RIGOL
Chapter 18 Specifications
All the specifications are guaranteed except the parameters marked with “Typical”
and the oscilloscope needs to operate for more than 30 minutes under the specified
operation temperature.
Sample
Sample Mode
Real-time Sample
Real Time
Sample Rate
Analog channe: 2 GSa/s (single-channel), 1 Gsa/s (dual-channel)
Digital channel: 1 GSa/s (max)
Peak Detect
Analog channe: 500 ps (single-channel), 1 ns (dual-channel)
Digital channel: 2 ns
Averaging
After both the channels finish N samples at the same time, N can
be 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048, 4096 or 8192.
High
Resolution
12 bits of resolution when ≥5 μs/div @ 1 GSa/s (or ≥10 μs/div @
500 MSa/s).
Min Detect
Pulse Width
Digital channel: 5 ns
Memory Depth
Analog channel:
single-channel: Auto, 14k pts, 140k pts, 1.4M pts, 14M pts and
56M pts (option) are available
dual-channel: Auto, 7k pts, 70k pts, 700k pts, 7M pts and 28M pts
(option) are available
Digital channel: 14M pts maximum
Input
Number of
Channels
MSO2XX2A/2XX2A-S: 2 analog channels+16 digital channels
DS2XX2A/2XX2A-S: 2 analog channels
Input Coupling
DC, AC or GND
Input
Impedance
Analog channe: (1 MΩ±1%) || (16 pF±3 pF) or 50 Ω±1.5%
Digital channel: (101 kΩ±1%)||(9 pF±1 pF)
Probe
Attenuation
Coefficient
Analog channe: 0.01X to 1000X, in 1-2-5 step
MSO2000A/DS2000A User’s Guide
18-1
RIGOL
Maximum
Input Voltage
(1MΩ)
Chapter 18 Specifications
Maximum Input Voltage of the Analog Channel
CAT I 300 Vrms, CAT II 100 Vrms,
Transient Overvoltage 1000 Vpk
with RP2200 10:1 probe: CAT II 300 Vrms
with RP3300 10:1 probe: CAT II 300 Vrms
with RP3500 10:1 probe: CAT II 300 Vrms
with RP5600 10:1 probe: CAT II 300 Vrms
Digital channel: CAT I 40Vrms, Transient Overvoltage 800 Vpk
Horizontal
Timebase
Scale
MSO/DS2302A/2302A-S: 1 ns/div to 1.000 ks/div
MSO/DS2202A/2202A-S: 2.000 ns/div to 1.000 ks/div
MSO/DS2102A/2102A-S/2072A/2072A-S:
5.000 ns/div to 1.000 ks/div
Deviation
between
Channels
1 ns (typical), 2 ns (max)
Max Record
Length
14 Mpts
Timebase
Accuracy[1]
≤ ± 25 ppm
Clock Drift
≤ ± 5 ppm/year
Max Delay
Range
Negative delay: ≥1 screen width
Positive delay: 1 s to 100,000 s
Timebase
Mode
Y-T, X-Y, Roll
Number of XYs
1
Waveform
Capture Rate2
50,000 wfms/s (dots display)
Vertical
Bandwidth
(-3dB)
18-2
MSO/DS2302A/2302A-S: DC to 300 MHz
MSO/DS2202A/2202A-S: DC to 200 MHz
MSO/DS2102A/2102A-S: DC to 100 MHz
MSO2000A/DS2000A User’s Guide
RIGOL
Chapter 18 Specifications
MSO/DS2072A/2072A-S: DC to 70 MHz
Single-shot
Bandwidth
MSO/DS2302A/2302A-S: DC
MSO/DS2202A/2202A-S: DC
MSO/DS2102A/2102A-S: DC
MSO/DS2072A/2072A-S: DC
to
to
to
to
300 MHz
200 MHz
100 MHz
70 MHz
Vertical
Resolution
Analog channe: 8 bit
Digital channel: 1 bit
Vertical Scale
When the input impedance is 50Ω: 500 μV/div to 1 V/div
When the input impedance is 1MΩ: 500 μV/div to 10 V/div
Offset Range
When the input impedance is 50Ω:
500 μV /div to 50 mV/div: ± 2 V
51 mV/div to 200 mV/div: ± 10 V
205 mV/div to 1 V/div: ± 12 V
When the input impedance is 1MΩ:
500 μV /div to 50 mV/div: ± 2 V
51 mV/div to 200 mV/div: ± 10 V
205 mV/div to 2 V/div: ± 50 V
2.05 V/div to 10 V/div: ± 100 V
Bandwidth
Limit[1]
MSO/DS2302A/2302A-S/2202A/2202A-S: 20 MHz/100 MHz
MSO/DS2102A/2102A-S/2072A/2072A-S: 20 MHz
Low Frequency
Response
(AC Coupling,
-3dB)
≤5 Hz (on BNC)
Calculated Rise
Time[1]
MSO/DS2302A/2302A-S: 1.2ns
MSO/DS2202A/2202A-S: 1.8 ns
MSO/DS2102A/2102A-S: 3.5 ns
MSO/DS2072A/2072A-S: 5 ns
DC Gain
Accuracy
±2% full scale
DC Offset
Accuracy
±0.1 div ± 2 mV ± 1% offset value
Channel to
Channel
Isolation
DC to maximum bandwidth: >40 dB
MSO2000A/DS2000A User’s Guide
18-3
RIGOL
Chapter 18 Specifications
Vertical (Digital Channel)
Threshold
Adjustable threshold of 8 channels per group
Threshold
Selection
TTL (700 mV)
5.0 V CMOS (+2.5 V), 3.3 V CMOS (+1.65 V)
2.5 V CMOS (+1.25 V), 1.8 V CMOS (+900 mV)
ECL (-650 mV)
PECL (+1.85 V)
LVDS (+600 mV)
0V
User
Threshold
Range
±20.0 V, 10 mV step
Threshold
Accuracy
±(100 mV+3% threshold setting)
Dynamic
Range
±10 V+Threshold
Minimum
Voltage Swing
500 mVpp
Input
Resistance
//101 KΩ
Probe Load
≈8 pF
Vertical
Resolution
1 bit
Trigger
Trigger Level
Range
Internal
± 5 div from center of the screen
EXT
±4V
Trigger Mode
Auto, Normal, Single
Holdoff Range
100 ns to 10 s
High
Frequency
Rejection[1]
75 kHz
Low
Frequency
Rejection[1]
75 kHz
18-4
MSO2000A/DS2000A User’s Guide
Chapter 18 Specifications
Trigger
Sensitivity
RIGOL
1 div (below 10 mV or noise rejection is enabled)
0.3 div (above 10 mV and noise rejection is disabled)
Edge Trigger
Edge Type
Rising, Falling, Rising/Falling
Pulse Trigger
Pulse
Condition
Positive Pulse Width (greater than, lower than, within specific
interval)
Negative Pulse Width (greater than, lower than, within specific
interval)
Pulse Width
Range
2 ns to 4 s
Runt Trigger
Pulse Width
Condition
None, >, <, <>
Pulse Polarity
Positive, Negative
Pulse Width
Range
2 ns to 4 s
Windows Trigger (Option)
Windows Type
Rising, Falling, Rising/Falling
Trigger
Position
Enter, Exit, Time
Windows
Time
16 ns to 4 s
Nth Edge Trigger (Option)
Edge Type
Rising, Falling
Idle Time
16 ns to 4 s
Edge Number
1 to 65535
Slope Trigger
Slope
Condition
Positive Slope (greater than, lower than, within specific interval)
Negative Slope (greater than, lower than, within specific interval)
Time Setting
10 ns to 1 s
Video Trigger (HDTV Option)
Signal
Standard
NTSC, PAL/SECAM, 480P, 576P (Standard)
720P, 1080P and 1080I (Option)
Pattern Trigger
Pattern
H, L, X, Rising, Falling
MSO2000A/DS2000A User’s Guide
18-5
RIGOL
Chapter 18 Specifications
Setting
Delay Trigger (Option)
Edge Type
Rising, Falling
Delay Type
>, <, <>, ><
Delay Time
2 ns to 4 s
TimeOut Trigger (Option)
Edge Type
Rising, Falling, Rising/Falling
Timeout time
16 ns to 4 s
Duration Trigger (Option)
Pattern
H, L, X
Trigger
Condition
>, <, <>
Duration Time
2 ns to 4 s
Setup/Hold Trigger
Edge Type
Rising, Falling
Data Type
H, L
Setup Time
2 ns to 1 s
Hold Time
2 ns to 1 s
RS232/UART Trigger
Polarity
Normal, Invert
Trigger
Condition
Start, Error, Check Error, Data
Baud Rate
2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600 bps,
115200 bps, User
Data Bits
5 bit, 6 bit, 7 bit, 8 bit
I2C Trigger
Trigger
Condition
Start, Restart, Stop, Missing ACK, Address, Data, A&D
Address Bits
7 bit, 8 bit, 10 bit
Address
Range
0 to 127, 0 to 255, 0 to 1023
Byte Length
1 to 5
SPI Trigger
Trigger
Condition
Timeout
Timeout Value
100 ns to 1 s
18-6
MSO2000A/DS2000A User’s Guide
RIGOL
Chapter 18 Specifications
Data Bits
4 bit to 32 bit
Data Line
Setting
H, L, X
CAN Trigger (Option)
Signal Type
Rx, Tx, CAN_H, CAN_L, Differential
Trigger
Condition
SOF, EOF, FrameType, FrameError
Signal Rate
10 kbps, 20 kbps, 33.3 kbps, 50 kbps, 62.5 kbps, 83.3 kbps, 100
kbps, 125 kbps, 250 kbps, 500 kbps, 800 kbps, 1 Mbps, User
Sample Points
5% to 95%
Frame Type
Data, Remote, Error, OverLoad
Error Type
Bit Fill, AnswerError, CheckError, FormatError, RandomError
USB Trigger (Option)
Signal Speed
Low Speed, Full Speed
Trigger
condition
SOP, EOP, RC, Suspend, Exit Suspend
Measure
Cursor
Manual Mode
Track Mode
Auto Mode
Auto
Measurement
Voltage Deviation between Cursors (△V)
Time Deviation between Cursors (△T)
Reciprocal of △T (Hz) (1/△T)
Voltage and Time Values of the Waveform
Point
Allow to display cursors during auto
measurement
Analog channel:
Maximum, Minimum, Peak-Peak Value, Top Value, Bottom Value,
Amplitude, Average, Mean Square Root on Whole Signal, Mean
Squrare Root on Single Period, Overshoot, Pre-shoot, Area, Period
Area, Frequency, Period, Rise Time, Fall Time, Positive Pulse
Width, Negative Pulse Width, Positive Duty Cycle, Negative Duty
Cycle, Delay 1 2 , Delay 1 2 , Delay 1 2 , Delay
1 2 , Phase 1 2 , Phase 1 2 , Phase 1 2 , Phase
1 2
Digital channel:
MSO2000A/DS2000A User’s Guide
18-7
RIGOL
Chapter 18 Specifications
Frequency, Period, Positive Pulse Width, Negative Pulse Width,
Positive Duty Cycle, Negative Duty Cycle, Delay 1 2 , Delay
1 2 , Delay 1 2 , Delay 1 2 , Phase 1 2 , Phase
1 2 , Phase 1 2 , Phase 1 2
Number of
Measurements
Display 5 measurements at the same time.
Measurement
Range
Screen or cursor
Measurement
Statistic
Current Value, Average, Max, Min, Standard Deviation, Number of
Measurements
Frequency
Counter
Hardware 6 bits frequency counter
(channels are selectable)
Math Operation
Waveform
Operation
A+B, A-B, A×B, A÷B, FFT, Editable Advanced Operation, Logic
Operation
FFT Window
Function
Rectangle, Hanning, Blackman, Hamming
FFT Display
Split, Full Screen
FFT Vertical
Scale
Vrms, dB
Logic
Operation
AND, OR, NOT, XOR
Math Function
Intg, Diff, Log, Exp, Sqrt, Sine, Cosine, Tangent
Number of
Buses for
Decoding
2
Decoding Type
Parallel (standard), RS232/UART (option), I2C (option), SPI
(option), CAN (option)
Display
Screen Type
8.0 inches (203 mm) TFT LCD display
Display
Resolution
800 Horizontal ×RGB×480 Vertical Pixel
18-8
MSO2000A/DS2000A User’s Guide
RIGOL
Chapter 18 Specifications
Display Color
160,000 Color (TFT)
Persistence
Time
Min, 50ms, 100ms, 200ms, 500ms, 1 s, 2 s, 5 s, 10 s, 20 s, Infinite
Display Type
Dots, Vectors
Real-time
Clock
Time and Date (user adjustable)
Signal Source (MSO2000A-S/DS2000A-S)
Channels
2
Sample Rate
200 MSa/s
Vertical
Resolution
14 bits
Max.
Frequency
25 MHz
Standard
Waveform
Sine, Square, Pulse, Ramp, Noise, DC
Built-in
Waveform
Sinc, Exponential Rise, Exponential Fall, ECG, Gauss, Lorentz,
Haversine
Sine
Frequency Range
100 mHz to 25 MHz
Flatness
±0.5 dB (relative to 1 kHz)
Harmonic
Distortion
-40 dBc
Stray
(Non-harmonic)
-40 dBc
Total Harmonic
Distortion
1%
S/N Ratio
40 dB
Frequency Range
Square: 100 mHz to 15 MHz
Pulse: 100 mHz to 1 MHz
Rise/Fall Time
<15 ns
Overshoot
<5%
Duty Cycle
Square: 50%
Pulse: 10% to 90% (user adjustable)
Duty Cycle
Resolution
1% or 10 ns (the larger of the two)
Square/Pulse
MSO2000A/DS2000A User’s Guide
18-9
RIGOL
Chapter 18 Specifications
Min. Pulse Width
20ns
Pulse Width
Resolution
10 ns or 5 bits (the larger of the two)
Jitter
500 ps
Frequency Range
100 mHz to 100 kHz
Linearity
1%
Symmetry
0 to 100%
Noise
Bandwidth
25 MHz (typical)
Built-in
Waveform
Frequency Range
100 mHz to 1 MHz
Arbitrary
Waveform
Frequency Range
100 mHz to 10 MHz
Waveform Length
2 to 16 k points
Internal Storage
Location
10
Accuracy
100 ppm (lower than 10 kHz)
50 ppm (higher than 10 kHz)
Resolution
100 mHz or 4 bits, the larger of the two
Output Range
20 mVpp to 5 Vpp, HighZ
10 mVpp to 2.5 Vpp, 50 Ω
Resolution
100 μV or 3 bits, the larger of the two
Accuracy
2% (1 kHz)
Range
±2.5 V, HighZ
±1.25 V, 50 Ω
Resolution
100 μV or 3 bits, the larger of the two
Accuracy
Offset setting Value±2%
Ramp
Frequency
Amplitude
DC Offset
I/O
Standard Ports
USB HOST (support USB-GPIB), USB DEVICE, LAN, Aux Output
(TrigOut/PassFail)
Printer
Compatibility
PictBridge
18-10
MSO2000A/DS2000A User’s Guide
RIGOL
Chapter 18 Specifications
General Specifications
Probe Compensation Output
Output Voltage[1]
Frequency
[1]
About 3 V, peak-peak
1 kHz
Power
Power Voltage
100 V to 240 V, 45 Hz to 440 Hz
Power
Maximum 50 W
Fuse
2 A, T Degree, 250 V
Environment
Temperature Range
Operating: 0 ℃ to +50 ℃
Non-operating: -40 ℃ to +70 ℃
Cooling Method
Humidity Range
Fan cooling
0℃ to +30℃: ≤95% Relative Humidity
+30℃ to +40℃: ≤75% Relative Humidity
+40℃ to +50℃: ≤45% Relative Humidity
Altitude
Operating: under 3,000 meters
Non-operating: under 15,000 meters
Physical Characteristics
Size[3]
Width×Height×Depth = 361.6 mm× 179.6 mm×130.8
mm
Weight[4]
Package Excluded
3.9 kg ± 0.5 kg
Package Included
4.5 kg ± 0.5 kg
Calibration Interval
The recommended calibration interval is one year.
Regulatory Information
Electromagnetic
Compatibility
2004/108/EC
Execution standard EN 61326-1:2006 EN 61326-2-1:2006
Safety
UL 61010-1:2004; CAN/CSA-C22.2 NO. 61010-1-2004;
EN 61010-1:2001; IEC 61010-1:2001
Note[1]: Typical.
Note[2]: Maximum value. 20ns, single-channel mode, dots display, auto memory depth.
Note[3]: Supporting legs and handle folded, knob height included.
Note[4]: Standard configuration.
MSO2000A/DS2000A User’s Guide
18-11
Download PDF