REV. 5-16-07
IMPORTANT-READ THIS BEFORE RUNNING
Running nitro kit is fun and easy, but to make
this a safe and good experience you must
observe a few rules. This kit is extremely fast,
easily over 65KPH, and can seriously injure
someone if you are not careful.
5. Emer gency Engine Stopping
Remove air filter and cover carb. intake.
Squeeze fuel line and hold until engine stops.
With a rag, cover exhaust outlet.
1. W here to r un car?
Any running area you choose must be dry.
Do not run car near any water or wet dirt.
Do not run on public streets. It is very easy to
have the car run over or be damaged by hitting
the curb.
Do not operate the car in tight confined
places. The car is very fast and will easily hit
something.
6. Storing Car After Running
Remove fuel from tank and fuel lines
Turn off radio in the car
Put a few drops of after run in the engine to keep
it from rusting.
Clear oil and dirt from chassis with a
degreaser.
Do not run near people or animals. The car is
very fast and could easily hit someone if you
are not an expert driver.
7. Precautions
Due to noise, you will want to consider the
surrounding area when operating the car.
Hot Parts-The pipe, manifold, engine and head
are very hot and will cause burns.
Do not operate the car at night. You will not
be able to drive it safely.
Rotating Parts-Keep hands away from the
drive train, wheels, and engine when engine
is running.
。キ
Do not operate the car indoors. Engine
exhaust fumes are dangerous.
2. Glow Fuel
Glow fuel is poisonous!
Glow fuel is flammable!
Do not leave in fuel bottle with lid off at any
time.
Do use any fuel other than glow fuel in this
engine.
3. Fir st Time Star ting the Engine
Caution!
W hen star ting the engine make sure the
following is obser ved.
Set engine Master needle to 3 turns
(rich setting)
Do not do this alone, get an experienced
friend to help for the first time.
Fill fuel tank, try not to spill fuel. Do not spill
fuel on receiver.
Hold car off the ground, so it will not runaway
when it first starts.
Turn onthe radio and check the linkage before
starting engine.
Turn on car receiver battery switch.
Always have an air filter on the carburetor to
keep dirt out.
4. Engine Break-in
See section.
This kit is not a toy. Always run car with a
second person as a spotter and pitman.
Radio-Check battery life before running the
car. The radio does not have full control of the
car with steering and/or throttle/brake, do not
run until corrected. Failure to correct this will
result in possible injury and damage to the
car or property. We strongly recommend
using a Failsafe.
Glow fuel-Do not leave the glow fuel
unattended with the lid off. Fuel contains
Methanol and Nitro Methane and is flammable
and poisonous.
Store fuel in cool ventilated location.
Refer to the glow fuel label for additional
precautions.
Fuel tank in the car-Never store fuel in car
tank, it will ruin the engine if left in tank.
Always turn off the car BEFORE turning off
the radio.
DAMAGE DUE CAR RUN AWAY IS NOT
A WARRANTY ISSUE .
IF YOU DO NOT BREAK-IN
ENGINE CORRECTLY, AT LOW-MID
RPM, YOU WILL BREAK THE
CONNECTING ROD!
FAILURE TO READ AND
FOLLOW BREAK-IN ENGINE
INSTRUCTIONS WILL VOID
WARRANTY!
REQUIRED FOR OPERATION
THINGS NEED BESIDES THE KIT
OFNA/Picco
JL Racing .12 Red Dot
Parts # 51124
Glow Plug Long Heat with Battery & Charger
# 10215....$27.95
(please note OFNA Glow Heats available)
Glow Fuel
20%
Bottle’s with spout
# 10160 - large 500cc
# 10161 - large 500 ccAuto Stop
# 10162 - small 250cc
# 10164 - CNC spout 500CC
# 10167 - CNC spout 800CC
Mini-Start
#10252 Mini-Start Blue
#10254 Mini-Start Gray
Off-Road Starter Box, 12V motor
# 10250 - 1/8 scale Starter Box
# 10253 - 1/8 scale Starter Box w/ Panel
Optional Parts
# 92571 - Power Panel Glow Heater
# 92572 - Cable for Glow Plug
Note: Pro kit does not include engine!
More Optional Parts . . .
RADIO CONTROL UNIT
#10200 5Cell AAA 800mah
Hump Pack .. $24.95
SUITABLE SERVO SIZE
(TYPE B)
(TYPE A)
Futaba- S9650
Hitec- HS-5245MG
AIRTRONICS - 94141Z
JR- DS3400G THROTTLE ONLY
# 10214 NiHm Battery Pack
Charger.. $7.95
JR- STEERING ONLY- DS9411
15~17mm
15~16mm
# 51007 OFNA/Picoo Glow
Plug .. $4.95
28~32mm
35~36mm
28~30mm
31~33mm
TOOLS NOT INCLUDED IN KIT
INCLUDED WITH KIT
Diff. Oil
Instant Cemment
Cutter
Shock Oil
Phillips Type Screw Drivers ( L )
Curved Scissors
#500
#1000
50/35 wt
Masking Tape
1.5mm Allen Wrench
Phillips Type Screw Drivers ( S )
Precision Caliper
2mm Allen Wrench
Brush
Needle Nose Pliers
Paints
2.5mm Allen Wrench
(special tool for all turnbuckles)
Knife
Cross Wrench
4'5'5.5'7mm Allen Wrench
PLASTIC PARTS FOR USE
40833
RECEIVER BOX
40836
FRONT AND REAR LOWER ARM
40834
SERVO SAVER
40839
FRONT C HUB
40835
DIFF. CASE
40837
FRONT UPPER ARM AND ARM HOLDER
40840
FRONT AND REAR GEAR BOX
PLASTIC PARTS FOR USE
30802
THROTTLE LINKAGE PLASTIC
40842
WING STAY & BUMPER
40841
FRONT KNUCKLEARM
40843
REAR UPRIGHT
40844
CENTER DIFF. MOUNT
40848
STABILIZER BALL END
37100
SHOCK PLASTIC
40852
WING
SYMBOL USED THROUGHOUT THE INSTRUCTION MANUAL
Degrease With
Motor Spray
Parts Bag Used
Do Not
Over Tighten
Tighten
BAG
Do Not
Over Tighten
Screw
Cement
Apply Screw
Cement
Apply Oil
Oil
Ensure Free
Movement
True-To-Scale
1:1
Contact Adhesive
Contact
Adhesive
Tighten
Apply Grease
Apply
Grease
Ensure
Free
Movement
Anti-clockwise
Rotation
Clockwise
Rotation
Rotate
Direction
Rotate
Direction
1 ASSEMBLY OF THE CENTER DIFF.
Tighten
Step 1
30779
4x10mm Washer
2.6x10mm
Step 2
30773
40805
30779
.....x8
Tight the diff screws in this order.
94046
2.6x10mm
Flat Head Screw
40011
1
3
4
2
.....x4
30773
4mm
Cross Pin
Dif f . Oil
.....x2
Use 1000 weight diff. oil in the
center.
Fill the Diff. Case to approx. 80%
with the Diff.Oil.
2 ASSEMBLY OF THE FRONT GEAR CASE
Step 1
94034
4x4mm Set Screw
Step 2
w t
r e en
Sc em
C
4x4mm
.....x1
40840
40806
37430
5x11mm Ball Bearing
Apply
Grease
.....x2
37430
38254
3x10mm
37430
38254
12x15x0.25mm Shim
40840
40804
.....x2
40813
38254
94003
3x10mm Hex Screw
.....x2
94043
3x35mm Hex Screw
.....x2
3x35mm
Adjust the backlash with the shims.
94003
3x10mm
Hex Screw
Step 2
3x10mm
.....x4
40842
40872
3x10mm
1:1
Down
3 ASSEMBLY OF THE FRONT SHOCK STAY
Step 1
* Notice the direction of the
front lower arm holder in front.
4 ASSEMBLY OF THE FRONT LOWER ARMS
* A 3x8mm set screw is
used to adjust ride-height.
3x8mm
Ensure
Free
Movement
3x8mm
94035
3x8mm
Set Screw
* Notice the direction of the
front lower arm holder in rear.
.....x1
40836
40837
Up
94004
3x12mm
Hex Screw
.....x2
1:1
1:1
40825
40837
Ensure
Free
Movement
40813
3x12mm
40825
40836
1:1
5 ASSEMBLY OF THE FRONT UPPER ARMS
1:1
*Approx. 8.5mm
40838
Step 1
Step 2
40826
40837
30403
94004
3x12mm
Hex Screw
40837
Ensure
Free
Movement
Anti-clockwise mark.
.....x2
40837
1:1
40837
30403
6mm Ball
.....x2
3x12mm
40824
Ensure
Free
Movement
1:1
6 ASSEMBLY OF THE KNUCKLE ARMS
Assembly for both right and left side.
Step 1
Step 3
Step 4
40839
.....x2
40841
Do Not
Over Thigten
37360
94003
3x10mm
Hex Screw
3x10mm
40818
40818
King Pin Bushing
S r
ew
Cecm
ent
40818
.....x2
Ensure
Free
Movement
Step 2
37430
40875
r ew t
Scemen
C
37430
5x11mm Ball Bearing
.....x2
37430
3x10mm
40840
37390
2x10.8mm Pin
.....x2
37390
Do Not
Over Thigten
7 ASSEMBLY OF THE FRONT SUSPENSION ARMS
94001
3x4mm
Hex Screw
.....x2
94005
3x15mm
Hex Screw
.....x2
Assembly for both right and left side.
Ensure
Free
Movement
3x4mm
40823
3x15mm
8 ASSEMBLY OF THE FRONT STABILIZER
94035
3x8mm
Set Screw
Assembly for both right and left side.
.....x2
30403
6mm Ball
Makes two rods for left and right
hand-side.
.....x2
40848
94005
3x15mm
Hex Screw
.....x2
3x8mm
30341
40848
30403
3x15mm
Screw
Cement
9 ASSEMBLY OF THE FRONT STABILIZER
3x3mm
S
Cecrew
me
nt
94033
3x3mm
Set Screw
3x3mm
.....x4
2.5mm
94044
2.5x8mm
Hex Screw
.....x2
40840
3x3mm
40817
40840
2.5x8mm
Ensure
Free
Movement
10 ASSEMBLY OF THE SERVO SAVER
40810
Step 2
Step 1
Ensure
Free
Movement
Step 2
40811
40834
37220
King Pin Bushing
40834
.....x2
94002
3x8mm
Hex Screw
40834
.....x2
37360
37360
Servo saver spring preload setting.
*Approx. 0.5mm
37220
37220
3x8mm
3x8mm
40809
37360
Do Not
Over Tighten
11 ASSEMBLY OF THE SERVO SAVER AND THE STEERING TIE-ROD
Screw
Cement
3x8mm
3x8mm
Step 1
94002
3x8mm
Hex Screw
Screw
Cement
Step 2
40834
.....x3
3x8mm
3x8mm
35958
94040
3x8mm Washer
35958
.....x2
37650
40827
35958
5x8x2.5mm Ball Bearing
.....x4
37650
40834
35958
1:1
*Approx. 37.5mm
40812
12 ASSEMBLY OF THE SERVO SAVER ONTO THE FRONT GEAR BOX
94002
3x8mm
Hex Screw
.....x2
3x8mm
13 ASSEMBLY OF THE REAR GEAR CASE
3x10mm
w t
re en
Sc em
C
4x4mm
Step 1
Step 2
40834
37430
5x11mm Ball Bearing
40840
.....x2
40806
37430
38254
38254
12x15x0.25mm Shim
.....x2
37430
3x10mm
40804
94003
3x10mm
Hex Screw
94043
3x35mm Hex Screw
.....x4
3x35mm
40840
38254
40815
.....x2
3x35mm
14 ASSEMBLY OF THE REAR SHOCK STAY
Step 1
Step 2
40842
94003
3x10mm
Hex Screw
.....x3
3x10mm
40873
3x10mm
15 ASSEMBLY OF THE WING STAY
40842
94003
3x10mm
Hex Screw
40842
.....x2
3x10mm
94004
3x12mm
Hex Screw
40842
3x12mm
40842
.....x4
40842
3x10mm
40842
16 ASSEMBLY OF THE WING STAY
Step 1
94004
3x12mm
Hex Screw
Step 2
.....x3
3x12mm
94005
3x15mm
Hex Screw
.....x1
40834
3x15mm
3x12mm
17 ASSEMBLY OF THE REAR LOWER ARMS
94035
3x8mm
Set Screw
.....x2
3x8mm
94004
3x12mm
Hex Screw
40836
.....x2
40837
Ensure
Free
Movement
1:1
*A 3x8mm set screw is
used to adjust ride-height.
40825
40837
3x8mm
40836
40816
Ensure
Free
Movement
1:1
3x12mm
18 ASSEMBLY OF THE REAR SUSPENSION ARMS
94001
3x4mm
Hex Screw
Assembly for both right and left side.
.....x2
40843
40875
37430
40840
37430
37430
5x11mm Ball Bearing
.....x4
37390
37390
2x10.8mm Pin
.....x2
40843
3x4mm
40823
Ensure
Free
Movement
19 ASSEMBLY OF THE REAR SUSPENSION ARMS
Assembly for both right and left side.
3mm
37100
40828
30403
6mm Ball
30403
37100
.....x4
30403
94041
3mm
Nylon Nut
.....x2
94005
3x15mm
Hex Screw
.....x4
3x15mm
1:1
*Approx. 48mm
3x15mm
20 ASSEMBLY OF THE REAR STABILIZER
94035
3x8mm
Set Screw
Assembly for both right and left side.
.....x2
30403
6mm Ball
.....x2
94005
3x15mm
Hex Screw
Makes two rods for left and right
hand-side.
40848
.....x2
30341
3x8mm
40848
30403
3x15mm
Screwnt
Ceme
21 ASSEMBLY OF THE REAR STABILIZER
3x3mm
S
Cecrew
me
nt
94033
3x3mm
Set Screw
.....x4
94044
2.5x8mm
Hex Screw
.....x2
3x3mm
2.5mm
40817
40840
40840
3x3mm
2.5x8mm
Ensure
Free
Movement
222ASSEMBLY OF THE CENTER DIFF. MOUNT
3x10mm
Step 2
Step 1
94033
3x3mm
Set Screw
Step 3
40844
40830
3x3mm
40844
.....x1
30171
94003
3x10mm
Hex Screw
39243
39243
40830
.....x4
1:1
*Approx. 12mm
39243
5x8mm
Flange Ball Bearing
.....x2
40844
23 ASSEMBLY OF THE BRAKE DISK INTO CENTER DIFF.
Step 2
Step 1
94033
3x3mm
Set Screw
3x3mm
.....x1
3x12mm
* Remove the double-side
tape before assembly.
40044
30171
38271
94004
3x12mm
Hex Screw
40044
.....x4
38272
double-side
tape
40042
* Leave a 1.5mm space between
the two brake pads.
40044
40044
3x12mm
1.5mm
40042
24 ASSEMBLY OF THE FRONT GEAR CASE ONTO CHASSIS
94019
3x10mm
Flat Head Hex Screw
.....x6
40801
3x10mm
3x10mm
3x10mm
3x10mm
1.5mm
25 ASSEMBLY OF THE CENTER DIFF. ONTO CHASSIS
*Insert the drive shaft into
the cap joint before assembly
center diff. onto chassis.
94019
3x10mm
Flat Head Hex Screw
40822
.....x4
3x10mm
3x10mm
26 ASSEMBLY OF THE REAR GEAR CASE ONTO CHASSIS
*Insert the drive shaft into
the cap joint before assembly
rear gear box onto chassis.
40822
94019
3x10mm
Flat Head Hex Screw
.....x6
3x10mm
3x10mm
3x10mm
27 SUITABLE SERVO
(CHECK YOUR SERVO BEFORE USE.)
TYPE A
TYPE B
Futaba- S9650
Hitec- HS-5245MG
AIRTRON ICS - 94141Z
JR- THROTTLE ONLY- DS3400G
JR- STEERING ONLY- DS9411
15~17mm
15~16mm
28~32mm
35~36mm
28~30mm
31~33mm
28 ASSEMBLY OF THE RADIO TRAY
TYPE A
3x8mm
3x8mm
Step 2
Step 1
40833
94018
3x5mm
Flat Head Hex Screw.....x1
94002
3x8mm
Hex Screw
40874
.....x10
3x8mm
3x8mm
3x5mm
40833
3x8mm
3x8mm
TYPE B
3x8mm
3x8mm
Step 2
Step 1
40833
94018
3x5mm
Flat Head Hex Screw
.....x3
94002
3x8mm
Hex Screw
.....x8
40833
3x8mm
94003
3x10mm
Hex Screw
40833
.....x2
3x8mm
3x5mm
3x10mm
3x5mm
40833
3x8mm
29 ASSEMBLY OF THE RADIO TRAY AND RECEIVER BOX
3x8mm
Step 1
94002
3x8mm
Hex Screw
*Use the screw provided
with your switch
Step 2
.....x2
40876
10281
Switch
40833
30 ASSEMBLY OF THE RADIO TRAY AND RECEIVER BOX
30560
40855
*Put the Servo and Switch wire into receiver box and connect to receiver .
*Arrangement the servo wire as picture shown.
40833
37410
40861
*Use the AAA type
bettery
Receiver
31 ASSEMBLY OF THE RADIO TRAY ONTO CHASSIS
94019
3x10mm
Flat Head Hex Screw
.....x5
3x10mm
3x10mm
32 ASSEMBLY OF THE STEERING SERVO AND STEERING ROD
1:1
*Approx. 40mm
*Ensure that servo gears are centered before attaching
the servo horns. The best way to accomplish this is by
connecting the servos to the radio system and setting
the trim to the center.
37650
37360
38398
Use the screw
provided with
your servo.
Sanwa/Airtronics
30661
JR
Futaba
HiTech
37650
S
J
F
H
* Choose the right servo horn adapter for your servo.
33 ASSEMBLY OF THE FUEL TANK ONTO CHASSIS
²ÕX
¦ ªo½cÜ
¦ ©³½L
TM-47
37070
37070
P3 O-Ring
*Put the P3 O-Ring under the fuel
tank before assembly.
.....x2
94019
3x10mm
Flat Head Hex Screw
37070
.....x2
Do Not
Over Tighten
3x10mm
34 ASSEMBLY OF THE CLUTCH
Step 1
Step 2
* Only use the #174D pilot shaft for threaded crank
shaft engine.
10091
Pilot Shaft
w nt
e
r
(Not Included)
S c me
*Place the clutch shoes with the clutch
springs over the 3 pins of the flywheel.
*Using a phillips screw driver or needle
nose pliers and bend the small end lf
the clutch spring behind the pilot shaft
#174C than press down.
Ce
Threaded
Crank Shaft
10330
40814
* Use the 7x12x0.5mm washer
only according to use different
engine.
7x12x0.5mm
10330
*Fit the flywheel using a pair of the
plIer and cross wrench.
S
Ce c r e
m w
en
t
10102
10098
10010
40814
35 ASSEMBLY OF THE CLUTCH AND ENGINE MOUNT
Step 1
10099
.....x1
3x8mm Washer
5x8x0.3mm Washer .....x1
3x12mm
3x12mm
Step 2
34110
5x10x4mm Ball Bearing
.....x2
35313
3mm
Nylon Nut
.....x4
5x8x0.8mm Washer
.....x2
5x8x0.8mm
3x5mm Cap Screw
34110
.....x1
34110
40864
3mm
3x8mm
10399
3x12mm Cap Screw
5x8x0.8mm
.....x4
3x5mm
5x8x0.3mm
*Slide the 3mm nylon
nut into engine mount.
*Useing the washer according
to the engine you use.
40864
36 ASSEMBLY OF THE ENGINE ONTO CHASSIS
Note book Paper.
94002
3x8mm
Hex Screw
*Use note book paper to set gear backlash
between spur gear and clutch bell gear,
applying pressure while retightening the
engine.
*If the space is not correct the spur gear
will be damaged.
.....x4
3x8mm
3x8mm
37 ASSEMBLY OF THE MANIFOLD AND MUFFLER
40879
Step 1
94034
4x4mm
Set Screw
Step 2
97501
.....x2
95700
94018
3x5mm
Flat Head Hex Screw
.....x1
95901
40878
10120
4x4mm
40832
4x4mm
3x5mm
40831
38 ASSEMBLY OF THE THROTTLE LINKAGE
Step 1
Step 2
Step 3
30802
94033
3x3mm
Set Screw
2.6x18mm
2x8mm
3x3mm
.....x2
30172
30802
2mm Nut
.....x2
40060
2.5mm Nylon Nut
10300
30802
30531
30661
2mm
.....x1
Ensure
Free
Movement
37100
(1mm)
37100
(2mm)
40829
3x3mm
30802
40829
3x10mm
2X8mm
Screw
40060
10300
.....x2
Cut off the servo saver as shown.
*Take the 1mm and 2mm washer
from shock plastic tree.
2.6X18mm
Screw
.....x1
14
39 ASSEMBLY OF THE THROTTLE LINKAGES INTO LEVER
3x3mm
10300
94033
3x3mm
Set Screw
10300
.....x2
*Snap on.
* Use the screw
provided with
your servo .
Sanwa/Airtronics
*Ensure that servo gears are centered before attaching
the servo horns. The best way to accomplish this is by
connecting the servos to the radio system and setting
the trim to the center.
S
10185
JR
J
Futaba
F
HiTech
H
* Choose the right servo horn adapter for your servo.
40 ADJUSTING THE ENGINE CONTROL LINKAGES
(Neutral)
(Throttle High)
(Brake)
Approx. 0.5mm
10300
10300
Idling adjusting
Screw
Approx. 1mm gap
Carburetor is Opening fully
Turn on the Transmitter then Receiver and set the
Engine Control Servo Trim to the neutral position.
Adjust the idling adjusting screw on the Carburetor
to be open approx. 1mm gap.
Adjust both of the 10300 Engine Control and Brake
linkage Accordingly.
Adjust the Engine while it is not running.
Adjust the Servo-Horn mounting position for the
Carburetor to be full open.
Change the pivot mounting position on the servo
horn in case the Carburetor is not open fully or
if it opening excessively. Or if available on the
Transmitter, adjust the Throttle high end point.
.
41 ASSEMBLY OF THE AIR FILTER
Step 1
94002
3x8mm
Hex Screw
Step 2
3x8mm
.....x1
40857
40856
*Apply filter oil to the
foam before use.
40856
40858
Adjust 10300 so the brakes work smoothly.
If the brakes apply too much or not enough,
adjust 36140 accordingly. Or if available on
the adjustment.
Adjust 36140 to change the front or rear brake.
42 ASSEMBLY OF THE FRONT SHOCKS
CORRECT SHOCK ASSEMBLY
*Assemble 2 sets for front.
Use 50wt oil for front.
Step 1
USE THE LARGER
2 HOLE PISTON
Step 2
2mm
Fit the o-ring into groove before
assembly.
37100
37967
C-Ring
2mm
.....x2
37967
Carefully screw the
shock shaft into the
bottom of the plastic
ball and until the
distance between the
ball end and the shock
body is 18mm for the
front.
40863
37967
Washer (Black)
18mm
N.B. Do not over tighten
as the plastic will strip.
37966
40845
.....x2
40881
37100
37967
P3 O-Ring
.....x4
Step 3
Step 4
Fill the shocks with oil.
Step 5
40862
50wt
30403
6mm Ball
.....x2
40854
3x20mm
37100
94007
3x20mm
Hex Screw
37080
.....x2
1.Pull down piston and pour oil
into shock cylinder.
2.To remove air bubbles by
slowly moving piston up and
down.
3.Pull down piston, attach
pressure top and shock oil
overflow with tissue paper.
40884
37100
30403
0
10
30
20
40
43 ASSEMBLY OF THE REAR SHOCKS
*Assemble 2 sets for rear.
Use 35wt oil for rear.
CORRECT SHOCK ASSEMBLY
USE THE LARGER 2mm
2 HOLE PISTON
Step 1
Step 2
37100
Fit the o-ring into groove before
assembly.
37967
C-Ring
2mm
.....x2
37967
Carefully screw the
shock shaft into the
bottom of the plastic
ball and until the
distance between the
ball end and the shock
body is 32mm for the
front.
N.B. Do not over tighten
as the plastic will strip.
37966
40866
40863
32mm
37967
Washer (Black)
.....x2
40883
Fill the shocks
with oil.
37967
P3 O-Ring
.....x4
30403
6mm Ball
94007
3x20mm
Hex Screw
37100
Step 3
.....x2
40862
35wt
37100
Step 4
Step 5
40854
37080
3x20mm
.....x2
1.Pull down piston and pour oil
into shock cylinder.
2.To remove air bubbles by
slowly moving piston up and
down.
3.Pull down piston, attach
pressure top and shock oil
overflow with tissue paper.
40884
0
10
20
30
40
30403
44 ASSEMBLY OF THE FRONT SHOCK ABSORBER
3mm
Nylon Nut
3x8mm
94041
3mm
Nylon Nut
.....x2
94040
3x8mm Washer
.....x2
94005
3x15mm
Hex Screw
.....x2
3x15mm
Assembly for both right and left side.
45 ASSEMBLY OF THE REAR SHOCK ABSORBER
94041
3mm
Nylon Nut
.....x2
94040
3x8mm Washer
.....x2
3x8mm
94005
3x15mm
Hex Screw
3mm
Nylon Nut
.....x2
3x15mm
Assembly for both right and left side.
46 ASSEMBLY OF THE FRONT BUMPER
Step 1
94003
3x10mm
Hex Screw
Step 3
40842
40842
.....x6
3x10mm
94004
3x12mm
Hex Screw
.....x2
3x10mm
40842
Step 2
94019
3x10mm
Flat Head Hex Screw
3x12mm
.....x2
40842
3x10mm
3x10mm
47 ASSEMBLY OF THE FUEL TUBE
Connect to carbulater.
10177
Connect to fuel nipple.
Connect to pressure nipple.
Connect to fuel tank nipple.
10177
48 ASSEMBLY OF THE WING
3X10mm
40842
10803
40842
Body Reamer
(Not included)
40852
Drill two 6mm holes for mounting.
94019
3x10mm
Flat Head Hex Screw
.....x2
49 ASSEMBLY OF THE TIRES AND WHEELS
Step 1
Step 3
Step 2
Apply instant glue into the groove of the wheel.
40850
T
N
TA E
S LU
IN G
40849
40851
50 ASSEMBLY OF THE TIRE ONTO FRONT KNUCKLE AND REAR HUB
Assembly for both right and left side.
40865
40865
* For other wheels please assembly as picture shown.
*Put the 5x8x0.8mm
washer behind the
2mm pin.
40865
Tire and Wheel assembly.
5x8x0.8mm
40865
37390
40865
51 ASSEMBLY OF THE BODY AND PAINTING
Cut out the body as shown.
Use a neutral detergent to remove any dirt and oil.
40853
Before cutting and making holes on the body,
put the unpainted body on the chassis
to confirm the mounting position and
location for holes and cutouts.
Mask the windows from the inside with masking tape.
10803
Body Reamer
( Not included)
Paint the body with polycarbonate spray paints.
Making two holes on the front and
one hole on the rear for body posts.
5mm
5mm
Cut out for engine.
Hole for fuel tank.
Spray Paint
52 MOUNTING BODY
37410
53 STARTING OF THE ENGINE
How to start the engine:
12V Starter and Starter Ring
( Not Included)
1.
2.
3.
4.
Turn on transmitter and then receiver.
Fill fuel tank with fuel bottle.
Connect 1.2V glow plug starter.
Start engine with 12V starter.
( Note the direction of the starter.)
5. After the engine be started, remove the
1.2V glow plug starter.
Starter rubber ring for car.
( Insert starter rubber
ring on the 12V starter.)
Glow Plug
1.2V Glow Plug Igniter
(Not Included)
(Not Included)
1.2V
Glow Plug
Igniter
Normal Plug
* Follow the engine manufacturer instruction
manuals regarding engine set-up, carburetor
and maintenance.
Turbo Plug
There is 2 types of glow plug available
"NORMAL or Turbo" depending of the
type of the engine.
12V Starter
*To start the car, attach a glow plug igniter
to the glow plug, and use either an electric
starter or starter box applied to the flywheel
exposed through the chassis.
1.2V
V
1.2
Note the direction of
the starter.
Connect with
12V battery.
Starter Box
(Not Included)
OPERATING YOUR MODEL SAFELY
Before Running
Your radio control model can
move at high speed and
therefore can cause injury to
people or damage property.
It is your responsibility to
operate your model safely.
Engine Start-Up
While Running
Cautions for Safety
For engine use, refer to the
manual included with the engine.
Check that the model turns in
proportion to the amount you
move the steering control of the
transmitter.
Do not run your model through
water. This may cause rust or
electrical problems.
To prime the engine with fuel,
press down the primer button.
Check that the speed of the
model changes in proportion to
the amount you move the speed
control of the transmitter.
For radio equipment, refer to
the manual included with the
radio.
Check that all screws and nuts
arc tight.
If the model begins to operate
by itself, there is someone
else on your frequency.
Do not try to operate your
model under these conditions
for it may go out of control.
If model does not operate
correctly stop it and find the
cause.
Check the batteries.
Attach one clip to the glow plug's
end and the other clip to one of
the cylinder cooling fins.
After Running
By pushing with your fingers the
air cleaner, interrupt the engine
Fill in the fuel.
After each run, the model is hot.
Beware of getting burned.
Quickly. pull the starter rope
(to start the engine).
Fully extend
transmitter antenna.
Switch off receiver.
Keep hands and tools away from
moving parts.
Adjust by screwing the needle
little by little.
Switch off transmitter.
Switch on transmitter.
OFF
OFF
ON
ON
Remove the clips from the engine.
Proper maintenance extends the
life of the model.
Switch on receiver.
Use genuine parts.
Never throw burning, gleaming
or smouldering things into fuel
cans even if these happen to be
empty.
This is very dangerous to life! I!
.12 ONLY
Jammin Mini CRT.5 Set-Up Sheet
Date:________________
Driver:_________________
Track:_______________/_______
Air Temp:__________
Surface Dsc. ___________________________
Front Suspension
Shock Spring: __________________
5
4
3
Avg. Lap Time:_______"______
Steering Ackerman Location
1
2
1
2
Shock Piston:
Shock Oil wt: __________0__________
6
Shock Length:________
(Center to Center)
mm
7
8
9
Toe-IN: _________
2
10
1
Front Sway Bar Preload
Toe-Out: ________
Front Ride Height: _____________
Sway Bar: ____________________
mm
Camber: Neg: ______
Pos: ______
Caster Angle:
(F/F)
F/F
F/R
Wheel
22
21
20
23
22
21
24
23
22
2
1
REBOUND STOP
(F/R)
Notes:____________________________________________
_____________________________________________
Rear Suspension
5
4
3
1
2
Front Sway Bar Preload
Shock Spring: _______________________
Shock Piston:
mm
Shock Oil wt: ________
Shock Length:________
(Center to Center)
6
7
mm
Wing Position
8
9
Rear Ride Height: ________mm
10
1
1
2
2
Sway Bar: ____________________
1
Camber: Neg: ______
2
1
3
Pos: ______
Anti-Squat Plate
3
2
Wheelbase
Rear Toe-In Plate
R/F
R/R
1 Degree
1 Degree
2 Degree
2 Degree
3 Degree
3 Degree
230mm
Wheel
2
(Right = Left)
(Right = Left)
Differential
227mm
1
REBOUND STOP
Tires
Front Type ____________Oil___________
Front Type: Brand_________________Compound_____________
Center Type ___________Oil___________
Rear Type: Brand_________________Compound______________
Rear Type ____________Oil___________
Note:_______________________________________________________________________________
Engine
Type:__________________
Foam:_________________
Foam:_________________
CLUTCH
Head Clearance_________
Shoe Brand____________________Compound__________________________
Pipe:___________________
Spring Brand____________________T
Fuel:__________% __ Plug____________
_
Needle (Top)________(Bottom)_______
Gearing:____T____T
ension___________________________
TO T
Note:_______________________________________________________________________________
BLANK
Jammin Mini CRT.5 Set-Up Sheet
Date:________________
Driver:_________________
Track:_______________/_______
Air Temp:__________
Surface Dsc. ___________________________
Front Suspension
Shock Spring: __________________
5
4
3
Avg. Lap Time:_______"______
Steering Ackerman Location
1
2
1
2
Shock Piston:
Shock Oil wt: __________0__________
6
Shock Length:________
(Center to Center)
mm
7
8
9
Toe-IN: _________
2
10
1
Front Sway Bar Preload
Toe-Out: ________
Front Ride Height: _____________
Sway Bar: ____________________
mm
Camber: Neg: ______
Pos: ______
Caster Angle:
(F/F)
F/F
F/R
Wheel
22
21
20
23
22
21
24
23
22
2
1
REBOUND STOP
(F/R)
Notes:____________________________________________
_____________________________________________
Rear Suspension
5
4
3
1
2
Front Sway Bar Preload
Shock Spring: _______________________
Shock Piston:
mm
Shock Oil wt: ________
Shock Length:________
(Center to Center)
6
7
mm
Wing Position
8
9
Rear Ride Height: ________mm
10
1
1
2
2
Sway Bar: ____________________
1
Camber: Neg: ______
2
1
3
Pos: ______
Anti-Squat Plate
3
2
Wheelbase
Rear Toe-In Plate
R/F
R/R
1 Degree
1 Degree
2 Degree
2 Degree
3 Degree
3 Degree
230mm
Wheel
2
(Right = Left)
(Right = Left)
Differential
227mm
1
REBOUND STOP
Tires
Front Type ____________Oil___________
Front Type: Brand_________________Compound_____________
Center Type ___________Oil___________
Rear Type: Brand_________________Compound______________
Rear Type ____________Oil___________
Note:_______________________________________________________________________________
Engine
Type:__________________
Foam:_________________
Foam:_________________
CLUTCH
Head Clearance_________
Shoe Brand____________________Compound__________________________
Pipe:___________________
Spring Brand____________________T
Fuel:__________% __ Plug____________
_
Needle (Top)________(Bottom)_______
Gearing:____T____T
ension___________________________
TO T
Note:_______________________________________________________________________________
BLANK
Jammin Mini CRT.5 Set-Up Sheet
Date:________________
Driver:_________________
Track:_______________/_______
Air Temp:__________
Surface Dsc. ___________________________
Front Suspension
Shock Spring: __________________
5
4
3
Avg. Lap Time:_______"______
Steering Ackerman Location
1
2
1
2
Shock Piston:
Shock Oil wt: __________0__________
6
Shock Length:________
(Center to Center)
mm
7
8
9
Toe-IN: _________
2
10
1
Front Sway Bar Preload
Toe-Out: ________
Front Ride Height: _____________
Sway Bar: ____________________
mm
Camber: Neg: ______
Pos: ______
Caster Angle:
(F/F)
F/F
F/R
Wheel
22
21
20
23
22
21
24
23
22
2
1
REBOUND STOP
(F/R)
Notes:____________________________________________
_____________________________________________
Rear Suspension
5
4
3
1
2
Front Sway Bar Preload
Shock Spring: _______________________
Shock Piston:
mm
Shock Oil wt: ________
Shock Length:________
(Center to Center)
6
7
mm
Wing Position
8
9
Rear Ride Height: ________mm
10
1
1
2
2
Sway Bar: ____________________
1
Camber: Neg: ______
2
1
3
Pos: ______
Anti-Squat Plate
3
2
Wheelbase
Rear Toe-In Plate
R/F
R/R
1 Degree
1 Degree
2 Degree
2 Degree
3 Degree
3 Degree
(Right = Left)
(Right = Left)
230mm
Wheel
2
Differential
227mm
1
REBOUND STOP
Tires
Front Type ____________Oil___________
Front Type: Brand_________________Compound_____________
Center Type ___________Oil___________
Rear Type: Brand_________________Compound______________
Rear Type ____________Oil___________
Note:_______________________________________________________________________________
Engine
Type:__________________
Foam:_________________
Foam:_________________
CLUTCH
Head Clearance_________
Shoe Brand____________________Compound__________________________
Pipe:___________________
Spring Brand____________________T
Fuel:__________% __ Plug____________
_
Needle (Top)________(Bottom)_______
Gearing:____T____T
ension___________________________
TO T
Note:_______________________________________________________________________________
BLANK
MINI CRT.5 PRO PARTS LIST
PART #
DESCRIPTION
RETAIL
10009
CLUTCH SHOES, RED, 3 SHOES
13.95
10098
CLUTCH NUT, SG SHAFT
4.95
10102
SPRINGS, CLUTCH, BLACK 3 PCS.
4.95
10120
SPRING, MANIFOLD, R.PORT .21
4.95
10177
FUEL LINE 3FT. GRAY/BLACK
1.95
10185
SILICONE JOINT TUBE BLACK
4.95
10270
CLIPS, FUEL LINE, BLK
3.95
10281
SW ITCH COVER, SILICONE RED
3.95
10300
ALUM. STOPPER KIT, 6 PCS.
4.95
10330
COLLET, FLYW HEEL INSERT .12/.21
2.95
10399
CLUTCH BELL W /BEARINGS, 13T
19.95
30171
LEVER, BRAKE
1.95
30172
RODS, BRAKES, 2 PCS.
1.5
30341
BALL END W ITH COLLAR, 6mm
3.95
30403
6mm BALL, STEEL (NO COLLAR)
4.95
30531
SPRING, THROTTLE LINKAGE
2.95
30560
ANT TUBE AND MOUNT
2.95
30661
SERVO HORN HEAVY DUTY BLACK
4.95
30773
CROSS PIN AXLES, 4mm STEEL
3.95
30779
MISC. PARTS, OLD DIFF & (k)
9.95
30802
LINKAGE, 2 THROTTLE LINKAGE
7.95
34110
BEARING, 5x10, 2 PCS
6.95
35958
BEARING, 5X8mm 1 PC.
3.95
37070
SEALS, O-RINGS, SHOCKS, 8 PCS.
1.95
37080
SEAL, TOP CAP, SHOCKS 4 PCS.
1.95
37100
PLASTIC PARTS, SHOCK, SET
4.95
37220
KING PINS SCREW , 3mm 4 PCS
1.95
37360
4mm BALL END SCREW , 10 PCS.
4.95
37390
PINS, 2x10.8mm, 3 PCS.
1.95
37410
BODY CLIPS, 10 PCS. SMALL
3.95
37430
BEARING, 5x11mm, 8 PCS.
15.95
37450
BEARING 10x15mm, 4 PCS.
15.95
37650
4mm PLASTIC BALL END, 10 PCS
6.95
37966
O-RING, SHOCK COLLOR, 4 PCS.
1.95
37967
REPAIR SEAL KIT,THREADED SHOCK
5.95
38254
W ASHER, 12X15X.02MM, 6PCS
1.95
38271
BRAKE PLATES, 2 PCS
3.95
38272
PADS, BRAKE, 2PCS
2.95
38398
TURNBUCKLE, 3x20mm PAIR
3.95
39243
BEARING, 5x8 FLANGED 2PCS
7.95
40009
SEAL, P-6 O-RING, DIFF, 2PCS
2.95
40011
GASKET, DIFF 3PCS
3.95
40042
BRAKE DISCS, STEEL 4PCS.
10.95
40044
SPRING, BRAKE SEPARATORS, 8PCS
5.95
40060
NYLOK NUT, 2.5, PISTON NUT, 4
4.95
40129
CONNECTOR, RUBBER FOR 40127
5.95
40801
CHASSIS, CRT.5 6061 ALUM.
45.95
40802
SPUR GEAR 46T CRT.5
39.95
40803
BEVEL GEAR 39T CRT.5
17.95
40804
PINION GEAR 12T CRT.5
14.95
40805
DIFF. GEAR SET CRT.5
17.95
40806
CAP JOINT FOR PINION GEAR EA.
9.95
40807
CAP JOINT BRAKE PAIR
14.95
40808
CAP JOINT FOR DIFF. PAIR
14.95
40809
SERVO SAVER ALUM. TUBE
9.95
40810
SERVO SAVER ADJUSTING RING
5.95
40811
SERVO SAVER SPRING CRT.5
3.95
40812
SERVO SAVER POST CRT.5 PAIR
7.95
40813
ARM HOLDER, LOW ER FR. ALUM.
9.95
40814
FLYW HEEL FOR CRT.5
14.95
40815
REAR TOE-IN PLATE ALUM.
9.95
40816
ANTI-SQUAT PLATE ALUM. CRT.5
9.95
PART #
DESCRIPTION
40817
SW AY BAR 2.Omm FR/RR CRT.5
40818
KING PIN SCREW CRT.5
40822
CENTER DRIVE SHAFT 44/82.5mm
40823
ARM PIN 3x25.8mm CRT.5
40824
ARM PIN 3x32mm CRT.5
40825
ARM PIN 3x53mm CRT.5
40826
TURNBUCKLE 3.5x24mm CRT.5
40827
TURNBUCKLE 3x50mm CRT.5
40828
TURNBUCKLE 3x60mm CRT.5
40829
BRAKE ROD 2x52mm CRT.5
40830
BRAKE CAM CRT.5
40831
MUFFLER STAY CRT.5
40832
MUFFLER STAY POST ALUM. CRT.5
40833
RECEIVER BOX CRT.5
40834
SERVO SAVER,CTR. BRACE,FR.PLT.
40835
DIFF. CASE (F&R) CRT.5
40836
ARMS, LOW ER (F&R)
40837
ARMS, FR UPPER & ARM HOLDER
40838
ARM BALL END, PLASTIC 3.5mm
40839
C-HUB (L&R) CRT.5
40840
GEAR CASE, 12mm W HEEL HUB
40841
STEERING KNUCKLE CRT.5
40842
BUMPER, W ING STAY CRT.
40843
REAR UP-RIGHT CRT.5
40844
CENTER DIFF. MOUNT
40845
SHOCK SHAFT, FRONT 3x36.5mm
40847
FUEL TANK CRT.5
40848
STABILIZER BALL END CRT.5 8PCS
40849
DISH W HEELS CRT.5 (YELLOW )4PCS
40850
TIRES, CRT.5 (2.2)
40851
SPONGE, INNER TIRE CRT.5 4PCS
40852
W ING CRT.5 YELLOW
40853
BODY, CRT.5 CLEAR
40854
ALUM. 6mm SHOCK END (BRW ) 4PCS
40855
ANT. TUBE FIXING NUT (BROW N)
40856
AIR FILTER SET CRT.5
40857
AIR FILTER FOAM CRT.5 PAIR
40858
AIR FILTER CNNTR 90DEG. CRT.5
40859
CROSS W RENCH CRT.5
40860
HEX W RENCH CRT.5
40861
BATTERY CASE (AAA) CRT.5
40862
SHOCK CAP CRT.5 4PCS. (BRW )
40863
SHOCK SPRING ADJ. RING (BRW )
40864
ENGINE MOUNT ADJUSTABLE H.C.
40865
NUT, FLANGE NYLON 4mm BROW N
40866
SHOCK SHAFT, REAR 3x49mm
40872
CNC 7075 FRONT SHOCK TOW ER
40873
CNC 7075 REAR SHOCK TOW ER
40874
GRAPHITE RADIO TRAY CRT.5
40875
UNIVERSAL JOINT F/R CRT.5
40876
PROTECTIVE FOAM RX BOX CRT.5
40877
PIPE, IN-LINE CRT.5 SET
40878
PIPE, ONLY FOR IN-LINE CRT.5
40879
MANIFOLD, ONLY FOR IN-LINE
40880
SHOCK SET FRONT CRT.5 H.C.
40881
SHOCK BODY, FRONT CRT.5
40882
SHOCK SET REAR CRT.5 H.C.
40883
SHOCK BODY REAR CRT.5
40884
SHOCK SPRINGS F/R SET GRAY/SOF
95700
SPRINGS & SEALS PURPLE, INLINE
95901
SEAL, BLUE, R.PORT N.R12, 2PCS
97501
SPRINGS, PIPE JOINT, 3 PCS.
RETAIL
4.95
2.95
14.95
4.95
7.95
7.95
4.95
4.95
4.95
2.95
4.95
4.95
0
9.95
9.95
7.95
9.95
9.95
2.95
7.95
9.95
7.95
9.95
7.95
7.95
7.95
14.95
4.95
14.95
19.95
7.95
7.95
16.95
12.95
2.95
17.95
7.95
5.95
5.95
5.95
7.95
11.95
5.95
16.95
11.95
7.95
25.95
27.95
29.95
32.95
1.95
89.95
64.95
18.95
39.95
24.95
39.95
24.95
14.95
8.95
3.95
3.95
BLANK
OPTION PARTS FOR CRT.5
30774
38457
40591
40872
40873
40874
40875
40876
40877
40878
40879
40880
40881
40882
40883
40884
40885
40886
40887
40888
40889
40890
40891
40892
40893
40894
40895
40896
40897
40898
40899
40900
40905
49009
ALU M . D IFF C R O SS PIN H C 6PC S.
PAD , BR AKE, C AR BO N & ST EEL PAD
BR AKE D ISK, FIBER X 1-C R /C R T
C N C 7075 FR O N T SH O C K T O W ER
C N C 7075 R EAR SH O C K T O W ER
G R APH IT E R AD IO T R AY C R T .5
U N IVER SAL JO IN T F/R C R T .5
PR O T EC T IVE FO AM R X BO X C R T .5
PIPE, IN -LIN E C R T .5 SET
PIPE, O N LY FO R IN -LIN E C R T .5
M AN IFO LD , O N LY FO R IN -LIN E
SH O C K SET FR O N T C R T .5 H .C .
SH O C K BO D Y, FR O N T C R T .5
SH O C K SET R EAR C R T .5 H .C .
SH O C K BO D Y R EAR C R T .5
SH O C K SPR IN G S F/R SET G R AY/SO F
PIPE, JAM M IN JP.5 IN -LIN E
C H ASSIS 7075 C N C C R T .5
G R APH IT E C EN T ER D IFF. PLAT E
C N C ALU M . KN U C KLE C R T .5 PAIR
U N IVER SAL, C EN T ER C R T .5
C N C ALU M . C EN T ER D IFF. M O U N T
SH O C K SPR IN G C R T .5 BLU E/M ED .
SH O C K SPR IN G C R T .5 W H IT E/H AR D
C N C 7075 C H ASIS BR AC E F&R C R T 5
C N C ALU M . SER VO SAVER L&R C R T 5
C N C SER VO SAVER C O N N EC T IN G PL.
C N C FR O N T U PPER AR M H O LD ER
C N C ALU M . C -H U B C R T .5 L&R
C N C ALU M . R EAR U P-R IG H T L&R
SPU R G EAR 46T LIG H T W EIG H T
ALU M . W H EEL H U B C R T .5
G R APH IT E FR O N T PLAT E C R T .5
BR AKE D ISK, C N C SPEC IAL C U T
9.95
31.95
14.95
25.95
27.95
29.95
29.95
1.95
89.95
64.95
18.95
39.95
24.95
39.95
24.95
14.95
89.95
125.95
22.95
69.95
39.95
49.95
12.95
12.95
49.95
125.95
17.95
17.95
75.95
69.95
29.95
12.95
24.95
19.95
BLANK
OWNER’S REGISTRATION CARD
OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling this kit will provide many hours of enjoyment.
The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date.
In the event that the kit is incomplete or component parts are broken due to error in manufacturer, contact your
dealer from which you purchased the kit for replacement part or call OFNA at (949) 586-2910 for your nearest dealer
location. Other items such as radio and engine other covered by individual warranties.
IMPORTANT!
Please print or type, filling in the information listed below and mail immediately
MAIL TO:
OFNA RACING
7 VANDERBILT
IRVINE, CA. 92618
TEL: (949) 586-2910
Write in Your Model Name and Part Number
REGISTRATION CARD
RACER’S NAME
TEL:(
)
ADDRESS
CITY
STATE
DEALER’S NAME
ZIP
TEL: (
ADDRESS
CITY
OFNA
7 Vanderbilt
Irvine, Ca. 92618
STATE
ZIP
)
Download PDF