LNE LED Driver LNE-120W Series / LNE- V120W

TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
LNE
Highlights & Features
–
–
–
–
–
–
North American and International AC voltage options
Up to 93.5% efficiency
6kV common mode & 4kV differential mode surge immunity
Active PFC. Meets IEC/EN 61000-3-2, Class C
Adjustable voltage & current; dimming option available
IP65 or IP67 assembly for indoor and outdoor applications
Safety Standards
CB Certified for worldwide use
Model Number:
LNE-☐V120W☐☐☐
Unit Weight:
0.98 kg (2.16 lb)
Dimensions (L x W x D): 220 x 68 x 38.8 mm
(8.66 x 2.68 x 1.53 inch)
General Description
Delta LNE series of LED drivers comes with different combinations of features to suit different application requirements and energy
optimization needs. Options include externally adjustable output voltage and current levels, and adjustment of LED brightness via 3way built-in dimming function. All models in the LNE series come with a full corrosion resistant aluminum casing, major international
safety certifications and are compliant with EN55015 immunity/Emissions/Harmonic requirements. The products are designed and
rigorously tested to work in various indoor and outdoor LED lighting conditions. High surge immunity (common mode: 6kV, differential
mode: 4kV), MTBF > 700,000hrs and compliance to IP65/IP67, all make the Delta LNE series an essential part of an energy efficient
LED lighting power solution for both indoor and outdoor applications.
Model Information
LNE LED Driver
Model Number
Input Voltage Range
Rated Output Voltage
Rated Output Current
LNE-12V120W☐☐☐
90-305Vac (LNE-☐V120W☐A☐)
12Vdc
10.00A
LNE-24V120W☐☐☐
90-264Vac (LNE-☐V120W☐C☐)
24Vdc
5.00A
LNE-36V120W☐☐☐
36Vdc
3.40A
LNE-48V120W☐☐☐
48Vdc
2.50A
Model Numbering
LN
E–
LED
Driver
Product Series
E – High
efficiency and
PFC
1
□V
Output Voltage
12V
24V
36V
48V
120W
□
Output Power Package Type
(120W series A – IP65 with potentiometers
model)
to adjust output voltage &
constant current level
D – IP67 with dimming cable
to adjust constant current
level
□
Safety Approval
A – UL approval
C – ENEC, CE, KC,
PSE and CCC approval
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
□
Variable
A – Delta
standard
TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
Specifications
Model Number
LNE-12V120W☐
LNE-24V120W☐
LNE-36V120W☐
LNE-48V120W☐
Input Ratings / Characteristics
Nominal Input Voltage
100-277Vac (LNE-☐V120W☐A☐)
Input Voltage Range*
90-305Vac (LNE-☐V120W☐A☐)
Nominal Input Frequency
90-264Vac (LNE-☐V120W☐C☐)
50-60Hz
Input Frequency Range
47-63Hz
Input Current
1.50A max. @ 115Vac, 0.70A max. @ 230Vac,
0.65A max. @ 277Vac
100-240Vac (LNE-☐V120W☐C☐)
Efficiency at 100% Load
115Vac
90.0% typ.
91.5% typ.
91.5% typ.
230Vac
92.0% typ.
93.0% typ.
93.0% typ.
93.5% typ.
277Vac
92.0% typ.
93.0% typ.
93.0% typ.
93.5% typ.
Max Inrush Current (Cold Start)
65A typ. @ 230Vac
Power Factor at 100% Load
0.98 typ. @ 115Vac
0.95 typ. @ 230Vac
0.93 typ. @ 277Vac
Total Harmonic Distortion
< 20% @ 115Vac/60 Hz & 230Vac/50 Hz (≥ 50% load)
< 20% @ 277Vac/50 Hz (≥ 75% load)
Leakage Current
< 0.75mA @ 305Vac (LNE-☐V120W☐A☐)
< 0.75mA @ 264Vac (LNE-☐V120W☐C☐)
* Output power is de-rated at low input voltage. Please refer to Fig. 2 on page 10.
2
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
92.0% typ.
TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
Power Factor Vs Output Load
LNE-12V120W☐
LNE-24V120W☐
LNE-36V120W☐
LNE-48V120W☐
3
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
Efficiency Vs Output Load at Nominal Output Voltage
LNE-12V120W☐
LNE-24V120W☐
LNE-36V120W☐
LNE-48V120W☐
4
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
Model Number
LNE-12V120W☐
LNE-24V120W☐
LNE-36V120W☐
LNE-48V120W☐
Nominal Output Voltage
12Vdc
24Vdc
36Vdc
48Vdc
LED System Voltage Range in CC Mode
6-12Vdc
12-24Vdc
18-36Vdc
24-48Vdc
Output Voltage Adjustment Range**
10.8-13.5V
22.0-27.0V
33.0-40.0V
43.0-53.0V
Nominal Output Current
10.0A
5.0A
3.4A
2.5A
Output Current Adjustment Range**
5.0-10.0A
2.5-5.0A
1.7-3.4A
1.25-2.5A
Output Power
120W
120W
122.4W
120W
Line Regulation
@ 90-305Vac (LNE-☐V120W☐A☐)
± 0.5%
± 2.0%
± 1.0%
± 0.5%
± 0.5%
PARD*** (20MHz)
< 150mVpp
< 150mVpp
< 200mVpp
< 200mVpp
Rise Time
< 50ms @ 115Vac & 230Vac & 277Vac
Start-up Time
Hold-up Time
1200ms typ. @ 115Vac (100% load)
500ms typ. @ 230Vac & 277Vac (100% load)
16ms typ. @ 115Vac & 230Vac & 277Vac (100% load)
Dynamic Response
(Overshoot & Undershoot O/P Voltage)
± 5% @ 0-90% load , @ 115Vac & 230Vac & 277Vac
(Slew Rate: 0.1A/µS)
Output Ratings / Characteristics*
@ 90-264Vac (LNE-☐V120W☐C☐)
Load Regulation (0-95% load)
@ 90-305Vac (LNE-☐V120W☐A☐)
@ 90-264Vac (LNE-☐V120W☐C☐)
* For power de-rating from 60°C to 70°C, see power de-rating at Fig.1 on page 10.
** For LNE-☐V120WA☐☐ package type only.
*** PARD is measured with an AC coupling mode, and in parallel with 0.1µF ceramic capacitor & 47µF electrolytic capacitor.
5
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
Model Number
LNE-12V120W☐
LNE-24V120W☐
LNE-36V120W☐
LNE-48V120W☐
Mechanical
Casing
Aluminium
Dimensions (L x W x D)
220 x 68 x 38.8 mm (8.66 x 2.68 x 1.53 inch)
Unit Weight
0.98 kg (2.16 lb)
Cooling System
Convection
Wire
Input
Output
Dimming
Noise (1 Meter from power supply)
2
VDE
H05RN-F3G1.0mm
UL
SJTW 18AWGX3C
VDE
UL
VDE
H07RN-F2x1.5mm
SJTW 14AWGX2C
H05RN-F2x1.0mm2
Line: Brown, Neutral: Blue,
PE: Green/Yellow
Line: Brown, Neutral: Blue,
PE: Green/Yellow
Positive: Red, Negative: Black
Positive: Red, Negative: Black
Positive: White, Negative: Blue
UL
SJTW 18AWGX2C
Positive: White, Negative: Blue
2
Sound Pressure Level (SPL) < 25dbA
Environment
Surrounding Air Temperature
Operating
-40°C to +70°C
Storage
-40°C to +85°C
Power De-rating
> 60°C de-rate power by 4% / °C
< 100Vac de-rate power by 2% / Vac
Operating Humidity
5 to 95% RH (Non-Condensing)
Operating Altitude
0 to 3,000 Meters (9,840 ft.)
Shock Test (Non-Operating)
IEC 60068-2-27, Half Sine Wave: 50G for a duration of 11ms,
3 shocks for each 3 directions
Vibration (Non-Operating)
IEC 60068-2-6, Random: 5Hz to 500Hz (2.09G);
20 min per axis for all X, Y, Z direction
Pollution Degree
2
Location Ratings
(Included in safety approvals)
Dry rating (LNE-☐V120W A☐☐)
Dry, damp ratings (LNE-☐V120W D☐☐)
Protections
Overvoltage
13.8-16.8V,
Latch Mode
27.6-33.6V,
Latch Mode
Overload / Overcurrent
95-108%of rated load current, constant current limit
Auto-Recovery when the fault is removed
Over Temperature
Hiccup Mode, Auto-Recovery when the fault is removed
Short Circuit
Constant current limit , Auto-Recovery when the fault is removed
Degree of Protection
IP65 (LNE-☐V120W A☐☐)
Protection Against Shock
IP67 (LNE-☐V120W D☐☐)
Class I with PE* connection
*PE: Primary Earth
6
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
41.4-50.4V,
Latch Mode
55.2-67.2V,
Latch Mode
TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
Model Number
LNE-12V120W☐
LNE-24V120W☐
LNE-36V120W☐
LNE-48V120W☐
Reliability Data
MTBF
> 700,000 hrs. per Telcordia SR-332
at Input: 115Vac, Output: 100% load, Ta: 25°C
Expected Cap Life Time
10 years (115Vac & 230Vac, 50% load @ 40°C)
Safety Standards / Directives
Electrical Safety
LNE-☐V120W☐C☐:
CB scheme to IEC 61347-1, IEC 61347-2-13
ENEC to EN 61347-1, EN 61347-2-13, EN 62384
CCC to GB19510.1, GB19510.14
KC to KC61347-1, KC61347-2-13, KC62384
PSE to J61347-1, J61347-2-13
LNE-☐V120W☐A☐:
cRUus to UL 8750 and CAN/CSA C22.2 No. 60950-1
In conformance with EMC Directive 2004/108/EC and Low Voltage
Directive 2006/95/EC (LNE-☐V120W☐C☐)
CE
Material and Parts
Galvanic Isolation
RoHS Directive 2011/65/EU Compliant
Input to Output
3.85kVac
Input to Ground
2.0kVac
Output to Ground
1.5kVac
EMC
EMC / Emissions
CISPR 15, EN 55015, GB17743
Compliance to CISPR 22, EN 55022, FCC Title 47: Class B
Immunity to
EN 61547, Compliance to EN 55024
Level 4 Criteria B2)
Level 3 Criteria A1)
Air Discharge: 15kV
Air Discharge: 8KV
Contact Discharge: 8kV
Contact Discharge: 6KV
Level 3 Criteria A1)
80MHz-1GHz, 10V/M with 1kHz tone / 80% modulation
Electrostatic Discharge
IEC 61000-4-2
Radiated Field
IEC 61000-4-3
Electrical Fast Transient / Burst
IEC 61000-4-4
Level 3 Criteria A1)
2kV
Surge
IEC 61000-4-5
Level 5 Criteria B
3)
Common Mode : 6kV
4)
Differential Mode : 4kV
Conducted
IEC 61000-4-6
Level 3 Criteria A
150kHz-80MHz, 10Vrms
Power Frequency Magnetic Fields
IEC 61000-4-8
Level 3 Criteria A
10A/Meter
Voltage Dips
IEC 61000-4-11
2)
1)
1)
100% dip, 0.5 cycle, Criteria A1)
70% dip, 10 cycle, Criteria B2) @ 100Vac & Criteria A1) @ 230Vac
Harmonic Current Emission
IEC/EN 61000-3-2, Class C; GB17625.1
(THD conditions: 115Vac & 230Vac @ ≥ 50% load,
277Vac @ ≥ 75% load)
Voltage Fluctuation and Flicker
IEC/EN 61000-3-3
1) Criteria A: Normal performance within the specification limits
2) Criteria B: Temporary degradation or loss of function which is self-recoverable
7
3) Asymmetrical: Common mode (Line to earth)
4) Symmetrical: Differential mode (Line to line)
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
Block Diagram
LNE-☐V120WA☐☐
LNE-☐V120WD☐☐
8
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
Dimensions
L x W x D: 220 x 68 x 38.8 mm [8.66 x 2.68 x 1.53 inch]
LNE-☐V120WA☐☐
LNE-☐V120WD☐☐
Item
9
Device Description
1
Input cable
2
Output cable
3
Constant voltage adjustment potentiometer
4
Constant current adjustment potentiometer
5
Dimming Cable
tc
T case (tc): Temperature hot spot location on case. The
temperature at this location will not exceed 80°C when used in
accordance to conditions in this data sheet.
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
Engineering Data
Output Load De-rating VS Surrounding Air Temperature
Note
1.
2.
3.
Fig. 1
Power supply components may degrade, or
be damaged, when the power supply is
continuously used outside the shaded region,
refer to the graph shown in Fig. 1.
If the output capacity is not reduced when the
surrounding air temperature >60°C, the
device will run into Over Temperature
Protection. When activated, the output
voltage will go into bouncing mode and will
recover
when
the
surrounding
air
temperature is lowered or the load is reduced
as far as necessary to keep the device in
working condition.
Depending
on
the
surrounding
air
temperature and output load delivered by the
power supply, the device can be very hot!
De-rating for All Mounting Orientation (All Models)
> 60°C de-rate power by 4% / °C
Output Load De-rating VS Input Voltage

Fig. 2
10
No output power de-rating for the input
voltage from:100Vac to 305Vac (LNE-☐V120W☐A☐),
100Vac to 264Vac (LNE-☐V120W☐C☐)
De-rating for Low Input Voltage (All Models)
< 100Vac de-rate power by 2% / Vac
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
Assembly & Installation
Mounting holes for LED driver assembly onto the mounting surface.
Ⓐ, Ⓑ
Mounting holes for the LED driver (device). There are 3 mounting holes at either end of the device (locations Ⓐ and Ⓑ in
Fig. 3). The device shall be mounted using a minimum of 2 out of the 3 mounting holes on both sides. Mounting shall be done
using M4 screws with minimum length of 5mm. If customer’s end system or panel where the device is mounted does not
have screw threads, please use suitable metal screw and nut to secure the device.
Ⓒ
Surface Ⓒ belongs to customer’s end product or panel where the device is mounted. The device should be mounted on a
sturdy heat conducting surface with minimum of 4 mounting holes, as detailed above.
Fig. 3
Mounting Hole Locations
Safety Instructions
–
–
–
–
–
–
–
–
–
–
11
ALWAYS switch mains of input power OFF before connecting and disconnecting the input voltage to the device. If mains are not
turned OFF, there is risk of explosion / severe damage.
To guarantee sufficient convection cooling, keep a distance of 50mm above and lateral distance to nearby objects.
The device is not recommended to be placed on low thermal conductive surfaces. For example, plastics.
DO NOT insert any objects into the device.
Note that the enclosure of the device can become very hot depending on the surrounding air temperature and output load
connected to the device. Risk of burns!
If the device is continuously operating outside the shaded region shown in Fig. 1. The device may be damaged or degraded.
When the PE (Green/Yellow) wire of the device is not connected, the device must be installed on a metal plate that has a PE
connection.
The current rating for the all wires, connected to the input and output wires of the device, must be rated higher than or equal to the
input and output current of the power supply. Please refer to the product specifications.
For device with dimming function, always ensure the dimming control is working properly.
Please ensure the correct tools are used for all adjustments and installations of the device. If in doubt, please consult your local
Delta support or contact us via info@DeltaPSU.com.
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
Functions
Start-up Time
The time required for the output voltage to reach 90% of its final steady state set value, after the input voltage is applied.
Rise Time
The time required for the output voltage to change from 10% to 90% of its final steady state set value.
Hold-up Time
Time between the collapse of the AC input voltage, and the output falling to 95% of its steady state set value.
■ Graph illustrating the Start-up Time, Rise Time, and Hold-up Time
Inrush Current
Dynamic Response (For CV Operation Only)
Inrush current is the peak, instantaneous, input current measured
and, occurs when the input voltage is first applied. For AC input
voltages, the maximum peak value of inrush current will occur
during the first half cycle of the applied AC voltage. This peak
value decreases exponentially during subsequent cycles of AC
voltage.
The power supply output voltage will remain within ±5% of its
steady state value, when subjected to a dynamic load from 0 to
100% of its rated current.
 90% Duty / 1 KHz
 90% Duty / 120 Hz
12
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
Operating Methods of LED Modules-CV and CC Operation
A typical LED power supply is able to either work in "constant
voltage mode (CV) or constant current mode (CC)" to drive the
LEDs. DELTA’s LNE drivers integrate CV+CC characteristics;
so operation in CV mode (with external LED driver), in region Ⓐ
or CC mode (direct drive, at area Ⓑ).
In the constant current region, the highest voltage at the output
of the driver depends on the configuration of the end systems.
Should there be any compatibility issues or other questions with
these adjustment methods, please contact with Delta.
Dimming Operations
This operation is available for LNE-☐V120WD☐☐ only.
The Dimming connection diagram for turning the lighting fixture ON/OFF can be configured as below.
LNE-☐V120WD☐☐
Please refer an example of reference configuration as follows.
1.
2.
13
Built-in 3 in 1 dimming function, IP67 rated. Output constant current level can be adjusted through output cable by connecting
a resistance or 1~10Vdc or 10V PWM signal between DIM+ and DIM-.
The LED lighting fixture can be turned ON/OFF by the switch.
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
3.
4.
Please DO NOT connect "DIM-" to "V-".
Reference resistance value for output current adjustment (Typical).
5.
1 ~ 10V dimming function for output current adjustment (Typical).
6.
10V PWM signal for output current adjustment is also possible. For additional information, please contact your Delta sales
representative.
7.
Please note that LNE-☐V120WD☐☐ can't turn the lighting fixture completely off (totally dark) by using any of these dimming
adjustment methods. To completely turn off the lighting fixture, the input AC voltage must be removed. See illustration on
previous page.
External Input Protection Device
The unit is protected at the L pin, with an internal fuse that cannot be replaced. The power supply has been tested and approved on
20A branch circuits without additional protection device. An external protection device is only required if the supplying branch has an
ampacity greater than above. Thus, if an external protective device is necessary, a 20 Ampere C-characteristic circuit breaker can be
utilized.
14
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
TECHNICAL DATASHEET
LED Driver
LNE-120W Series / LNE-□V120W □□□
Overload & Overcurrent Protections (Auto-Recovery)
Overvoltage Protection (Latch Mode)
The power supply’s Overload (OLP) and Overcurrent (OCP)
Protections will be activated when output current is between 95%
and 108% of IO (Max load). Upon such an occurrence, the VO
(output voltage) will start to droop. Once the power supply has
reached its maximum power limit, the protection will be activated;
and, the power supply will operate in “CC mode”. The power
supply will recover once the fault condition once the cause of
OLP or OCP is removed, and IO is back within the specified range.
The power supply’s overvoltage circuit will be activated when its
internal feedback circuit fails. The output voltage shall not exceed
its specifications defined on Page 6 under “Protections”. Power
supply will latch off, and require removal/re-application of input
AC voltage in order to restart.
The power supply should be latch.
Over Temperature Protection (Auto-Recovery)
Short Circuit Protection (Auto-Recovery)
The power supply’s output OLP/OCP function also provides
protection against short circuits. When a short circuit is applied,
the power supply will operate in “CC mode”, as shown in the
illustration in the OLP/OCP section on this page. The power
supply will return to normal operation after the short circuit is
removed.
As mentioned above, the power supply also has Over
Temperature Protection (OTP). In the event of a higher operating
temperature at 100% load, the power supply will run into OTP
when the operating temperature is beyond what is recommended
in the de-rating graph. When activated, the output voltage will go
into bouncing mode until the temperature drops to its normal
operating temperature as recommended in the de-rating graph.
Others
Delta RoHS Compliant
Restriction of the usage of hazardous substances
The European directive 2011/65/EU limits the maximum impurity level of homogeneous materials such as lead,
mercury, cadmium, chrome, polybrominated flame retardants PBB and PBDE for the use in electrical and
electronic equipment. RoHS is the abbreviation for “Restriction of the use of certain hazardous substances in
electrical and electronic equipment”.
This product conforms to this standard.
PFC – Norm EN 61000-3-2
Line Current Harmonic content
Typically, the input current waveform is not sinusoidal due to the periodical peak charging of the input capacitor.
In industrial environment, complying with EN 61000-3-2 is only necessary under special conditions. Complying
to this standard can have some technical drawbacks, such as lower efficiency as well as some commercial
aspects such as higher purchasing costs. Frequently, the user does not profit from fulfilling this standard,
therefore, it is important to know whether it is mandatory to meet this standard for a specific application.
15
All parameters are specified at 25°C ambient for all products unless otherwise indicated.
www.DeltaPSU.com (April 2016, Rev. 02)
Download PDF